All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v5 0/2] Add APNE PCMCIA 100 Mbit support
@ 2021-06-19  0:34 Michael Schmitz
  2021-06-19  0:34 ` [PATCH v5 1/2] m68k: io_mm.h - add APNE 100 MBit support Michael Schmitz
  2021-06-19  0:34 ` [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver Michael Schmitz
  0 siblings, 2 replies; 9+ messages in thread
From: Michael Schmitz @ 2021-06-19  0:34 UTC (permalink / raw)
  To: linux-m68k, geert; +Cc: alex

Add another ISA type for these cards, and try to autoprobe for that type
early in the device probe. As a fallback, it is possible to switch to
the new type through a module parameter. 

Support for the 16 bit 10/100 Mbit cards is now included by default.

Compile tested only - I hope Alex can test the autoprobe bit now that
we know mode selection by module parameter works.

Cheers,

   Michael


^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH v5 1/2] m68k: io_mm.h - add APNE 100 MBit support
  2021-06-19  0:34 [PATCH v5 0/2] Add APNE PCMCIA 100 Mbit support Michael Schmitz
@ 2021-06-19  0:34 ` Michael Schmitz
  2021-06-19  0:34 ` [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver Michael Schmitz
  1 sibling, 0 replies; 9+ messages in thread
From: Michael Schmitz @ 2021-06-19  0:34 UTC (permalink / raw)
  To: linux-m68k, geert; +Cc: alex, Michael Schmitz

Add code to support 10 Mbit and 100 Mbit mode for APNE driver.

A new ISA type ISA_TYPE_AG16 dynamically switches the Amiga
ISA inb accessor to word access as required by the 100 Mbit cards.

Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
100 MBit card support" submitted to netdev 2018/09/16 by Alex
Kazik <alex@kazik.de>.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

--
Changes from v4:

Geert Uytterhoeven:
- drop CONFIG_APNE100MBIT ifdefs

Changes from v3:

Finn Thain:
- revert isa_inb() define reordering
- omit redundant #ifdef around ISA_TYPE_AG16 case labels

Changes from v1:

Andreas Schwab:
- remove redundant fallthrough annotations

Changes from RFC:

Geert Uytterhoeven:
- rename ISA_TYPE_AG100 to ISA_TYPE_AG16 (16 bit cards)
- move ISA_TYPE_AG16 case inside #ifdef CONFIG_AMIGA_PCMCIA
- change #if defined(CONFIG_APNE_100MBIT) to #ifdef
- fix parentheses in isa_inb() define
- omit comment about compiler optimization

- add ISA_TYPE_AG16 case to isa_delay()
---
 arch/m68k/include/asm/io_mm.h | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/arch/m68k/include/asm/io_mm.h b/arch/m68k/include/asm/io_mm.h
index 9c521b0..68922ef 100644
--- a/arch/m68k/include/asm/io_mm.h
+++ b/arch/m68k/include/asm/io_mm.h
@@ -65,12 +65,10 @@
 #define AG_ISA_IO_B(ioaddr) ( GAYLE_IO+(ioaddr)+(((ioaddr)&1)*GAYLE_ODD) )
 #define AG_ISA_IO_W(ioaddr) ( GAYLE_IO+(ioaddr) )
 
-#ifndef MULTI_ISA
-#define MULTI_ISA 0
-#else
+#ifdef MULTI_ISA
 #undef MULTI_ISA
-#define MULTI_ISA 1
 #endif
+#define MULTI_ISA 1	/* Need MULTI_ISA for 16 bit PCMCIA card support ! */
 #endif /* AMIGA_PCMCIA */
 
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -101,6 +99,8 @@
 #define ISA_TYPE_Q40  (1)
 #define ISA_TYPE_AG   (2)
 #define ISA_TYPE_ENEC (3)
+#define ISA_TYPE_AG16 (4)	/* for 100 MBit APNE card */
+
 
 #if defined(CONFIG_Q40) && !defined(MULTI_ISA)
 #define ISA_TYPE ISA_TYPE_Q40
@@ -136,6 +136,7 @@ static inline u8 __iomem *isa_itb(unsigned long addr)
     case ISA_TYPE_Q40: return (u8 __iomem *)Q40_ISA_IO_B(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u8 __iomem *)AG_ISA_IO_B(addr);
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -155,6 +156,7 @@ static inline u16 __iomem *isa_itw(unsigned long addr)
     case ISA_TYPE_Q40: return (u16 __iomem *)Q40_ISA_IO_W(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u16 __iomem *)AG_ISA_IO_W(addr);
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -171,6 +173,7 @@ static inline u32 __iomem *isa_itl(unsigned long addr)
   switch(ISA_TYPE)
     {
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u32 __iomem *)AG_ISA_IO_W(addr);
 #endif
     }
@@ -184,6 +187,7 @@ static inline u8 __iomem *isa_mtb(unsigned long addr)
     case ISA_TYPE_Q40: return (u8 __iomem *)Q40_ISA_MEM_B(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u8 __iomem *)addr;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -203,6 +207,7 @@ static inline u16 __iomem *isa_mtw(unsigned long addr)
     case ISA_TYPE_Q40: return (u16 __iomem *)Q40_ISA_MEM_W(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u16 __iomem *)addr;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -216,7 +221,7 @@ static inline u16 __iomem *isa_mtw(unsigned long addr)
 }
 
 
-#define isa_inb(port)      in_8(isa_itb(port))
+#define isa_inb(port)      ((ISA_TYPE == ISA_TYPE_AG16) ? ((port) & 1 ? isa_inw((port) - 1) & 0xff : isa_inw(port) >> 8) : in_8(isa_itb(port)))
 #define isa_inw(port)      (ISA_SEX ? in_be16(isa_itw(port)) : in_le16(isa_itw(port)))
 #define isa_inl(port)      (ISA_SEX ? in_be32(isa_itl(port)) : in_le32(isa_itl(port)))
 #define isa_outb(val,port) out_8(isa_itb(port),(val))
@@ -270,6 +275,7 @@ static inline void isa_delay(void)
     case ISA_TYPE_Q40: isa_outb(0,0x80); break;
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16: break;
     case ISA_TYPE_AG: break;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
-- 
2.7.4


^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19  0:34 [PATCH v5 0/2] Add APNE PCMCIA 100 Mbit support Michael Schmitz
  2021-06-19  0:34 ` [PATCH v5 1/2] m68k: io_mm.h - add APNE 100 MBit support Michael Schmitz
@ 2021-06-19  0:34 ` Michael Schmitz
  2021-06-19  0:56   ` Finn Thain
  2021-06-19  9:08   ` Geert Uytterhoeven
  1 sibling, 2 replies; 9+ messages in thread
From: Michael Schmitz @ 2021-06-19  0:34 UTC (permalink / raw)
  To: linux-m68k, geert; +Cc: alex, Michael Schmitz, netdev

Add Kconfig option, module parameter and PCMCIA reset code
required to support 100 Mbit PCMCIA ethernet cards on Amiga.

10 Mbit and 100 Mbit mode are supported by the same module.
A module parameter switches Amiga ISA IO accessors to word
access by changing isa_type at runtime. Additional code to
reset the PCMCIA hardware is also added to the driver probe.

Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
100 MBit card support" submitted to netdev 2018/09/16 by Alex
Kazik <alex@kazik.de>.

CC: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
Tested-by: Alex Kazik <alex@kazik.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

--
Changes from v4:

Geert Uytterhoeven:
- remove APNE100MBIT config option, always include 16 bit support
- change module parameter permissions
- try autoprobing for 16 bit mode early on in device probe

Changes from v3:

- change module parameter name to match Kconfig help

Finn Thain:
- fix coding style in new card reset code block
- allow reset of isa_type by module parameter

Changes from v1:

- fix module parameter name in Kconfig help text

Alex Kazik:
- change module parameter type to bool, fix module parameter
  permission

Changes from RFC:

Geert Uytterhoeven:
- change APNE_100MBIT to depend on APNE
- change '---help---' to 'help' (former no longer supported)
- fix whitespace errors
- fix module_param_named() arg count
- protect all added code by #ifdef CONFIG_APNE_100MBIT
---
 drivers/net/ethernet/8390/Kconfig |  4 ++++
 drivers/net/ethernet/8390/apne.c  | 33 +++++++++++++++++++++++++++++++++
 2 files changed, 37 insertions(+)

diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index 9f4b302..cf0d8b3 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -143,6 +143,10 @@ config APNE
 	  To compile this driver as a module, choose M here: the module
 	  will be called apne.
 
+	  The driver also supports 10/100Mbit cards (e.g. Netgear FA411,
+	  CNet Singlepoint). To activate 100 Mbit support at runtime or
+	  from the kernel command line, use the apne.100mbit module parameter.
+
 config PCMCIA_PCNET
 	tristate "NE2000 compatible PCMCIA support"
 	depends on PCMCIA
diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
index fe6c834..8223e15 100644
--- a/drivers/net/ethernet/8390/apne.c
+++ b/drivers/net/ethernet/8390/apne.c
@@ -120,6 +120,10 @@ static u32 apne_msg_enable;
 module_param_named(msg_enable, apne_msg_enable, uint, 0444);
 MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
 
+static bool apne_100_mbit;
+module_param_named(100_mbit, apne_100_mbit, bool, 0644);
+MODULE_PARM_DESC(100_mbit, "Enable 100 Mbit support");
+
 struct net_device * __init apne_probe(int unit)
 {
 	struct net_device *dev;
@@ -139,6 +143,11 @@ struct net_device * __init apne_probe(int unit)
 	if ( !(AMIGAHW_PRESENT(PCMCIA)) )
 		return ERR_PTR(-ENODEV);
 
+	if (apne_100_mbit)
+		isa_type = ISA_TYPE_AG16;
+	else
+		isa_type = ISA_TYPE_AG;
+
 	pr_info("Looking for PCMCIA ethernet card : ");
 
 	/* check if a card is inserted */
@@ -147,6 +156,20 @@ struct net_device * __init apne_probe(int unit)
 		return ERR_PTR(-ENODEV);
 	}
 
+	/* Reset card. Who knows what dain-bramaged state it was left in. */
+	{	unsigned long reset_start_time = jiffies;
+
+		outb(inb(IOBASE + NE_RESET), IOBASE + NE_RESET);
+
+		while ((inb(IOBASE + NE_EN0_ISR) & ENISR_RESET) == 0)
+			if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
+				pr_info("Card not found (no reset ack).\n");
+				isa_type=ISA_TYPE_AG16;
+			}
+
+		outb(0xff, IOBASE + NE_EN0_ISR);		/* Ack all intr. */
+	}
+
 	dev = alloc_ei_netdev();
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
@@ -590,6 +613,16 @@ static int init_pcmcia(void)
 #endif
 	u_long offset;
 
+	/* reset card (idea taken from CardReset by Artur Pogoda) */
+	if (isa_type == ISA_TYPE_AG16) {
+		u_char  tmp = gayle.intreq;
+
+		gayle.intreq = 0xff;
+		mdelay(1);
+		gayle.intreq = tmp;
+		mdelay(300);
+	}
+
 	pcmcia_reset();
 	pcmcia_program_voltage(PCMCIA_0V);
 	pcmcia_access_speed(PCMCIA_SPEED_250NS);
-- 
2.7.4


^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19  0:34 ` [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver Michael Schmitz
@ 2021-06-19  0:56   ` Finn Thain
  2021-06-19  3:13     ` Michael Schmitz
  2021-06-19  9:08   ` Geert Uytterhoeven
  1 sibling, 1 reply; 9+ messages in thread
From: Finn Thain @ 2021-06-19  0:56 UTC (permalink / raw)
  To: Michael Schmitz; +Cc: linux-m68k, geert, alex, netdev

On Sat, 19 Jun 2021, Michael Schmitz wrote:

> Add Kconfig option, module parameter and PCMCIA reset code
> required to support 100 Mbit PCMCIA ethernet cards on Amiga.
> 
> 10 Mbit and 100 Mbit mode are supported by the same module.
> A module parameter switches Amiga ISA IO accessors to word
> access by changing isa_type at runtime. Additional code to
> reset the PCMCIA hardware is also added to the driver probe.
> 
> Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
> 100 MBit card support" submitted to netdev 2018/09/16 by Alex
> Kazik <alex@kazik.de>.
> 
> CC: netdev@vger.kernel.org
> Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
> Tested-by: Alex Kazik <alex@kazik.de>
> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
> 
> --
> Changes from v4:
> 
> Geert Uytterhoeven:
> - remove APNE100MBIT config option, always include 16 bit support
> - change module parameter permissions
> - try autoprobing for 16 bit mode early on in device probe
> 
> Changes from v3:
> 
> - change module parameter name to match Kconfig help
> 
> Finn Thain:
> - fix coding style in new card reset code block
> - allow reset of isa_type by module parameter
> 
> Changes from v1:
> 
> - fix module parameter name in Kconfig help text
> 
> Alex Kazik:
> - change module parameter type to bool, fix module parameter
>   permission
> 
> Changes from RFC:
> 
> Geert Uytterhoeven:
> - change APNE_100MBIT to depend on APNE
> - change '---help---' to 'help' (former no longer supported)
> - fix whitespace errors
> - fix module_param_named() arg count
> - protect all added code by #ifdef CONFIG_APNE_100MBIT
> ---
>  drivers/net/ethernet/8390/Kconfig |  4 ++++
>  drivers/net/ethernet/8390/apne.c  | 33 +++++++++++++++++++++++++++++++++
>  2 files changed, 37 insertions(+)
> 
> diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
> index 9f4b302..cf0d8b3 100644
> --- a/drivers/net/ethernet/8390/Kconfig
> +++ b/drivers/net/ethernet/8390/Kconfig
> @@ -143,6 +143,10 @@ config APNE
>  	  To compile this driver as a module, choose M here: the module
>  	  will be called apne.
>  
> +	  The driver also supports 10/100Mbit cards (e.g. Netgear FA411,
> +	  CNet Singlepoint). To activate 100 Mbit support at runtime or
> +	  from the kernel command line, use the apne.100mbit module parameter.
> +
>  config PCMCIA_PCNET
>  	tristate "NE2000 compatible PCMCIA support"
>  	depends on PCMCIA
> diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
> index fe6c834..8223e15 100644
> --- a/drivers/net/ethernet/8390/apne.c
> +++ b/drivers/net/ethernet/8390/apne.c
> @@ -120,6 +120,10 @@ static u32 apne_msg_enable;
>  module_param_named(msg_enable, apne_msg_enable, uint, 0444);
>  MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
>  
> +static bool apne_100_mbit;
> +module_param_named(100_mbit, apne_100_mbit, bool, 0644);
> +MODULE_PARM_DESC(100_mbit, "Enable 100 Mbit support");
> +
>  struct net_device * __init apne_probe(int unit)
>  {
>  	struct net_device *dev;
> @@ -139,6 +143,11 @@ struct net_device * __init apne_probe(int unit)
>  	if ( !(AMIGAHW_PRESENT(PCMCIA)) )
>  		return ERR_PTR(-ENODEV);
>  
> +	if (apne_100_mbit)
> +		isa_type = ISA_TYPE_AG16;
> +	else
> +		isa_type = ISA_TYPE_AG;
> +
>  	pr_info("Looking for PCMCIA ethernet card : ");
>  
>  	/* check if a card is inserted */
> @@ -147,6 +156,20 @@ struct net_device * __init apne_probe(int unit)
>  		return ERR_PTR(-ENODEV);
>  	}
>  
> +	/* Reset card. Who knows what dain-bramaged state it was left in. */
> +	{	unsigned long reset_start_time = jiffies;

There's a missing line break here.

> +
> +		outb(inb(IOBASE + NE_RESET), IOBASE + NE_RESET);
> +
> +		while ((inb(IOBASE + NE_EN0_ISR) & ENISR_RESET) == 0)
> +			if (time_after(jiffies, reset_start_time + 2*HZ/100)) {

You could use msecs_to_jiffies(20) here.

> +				pr_info("Card not found (no reset ack).\n");
> +				isa_type=ISA_TYPE_AG16;

Whitespace is needed around the '='.

> +			}

Missing a break statement?

> +
> +		outb(0xff, IOBASE + NE_EN0_ISR);		/* Ack all intr. */
> +	}
> +
>  	dev = alloc_ei_netdev();
>  	if (!dev)
>  		return ERR_PTR(-ENOMEM);
> @@ -590,6 +613,16 @@ static int init_pcmcia(void)
>  #endif
>  	u_long offset;
>  
> +	/* reset card (idea taken from CardReset by Artur Pogoda) */
> +	if (isa_type == ISA_TYPE_AG16) {
> +		u_char  tmp = gayle.intreq;
> +

Extra whitespace.

> +		gayle.intreq = 0xff;
> +		mdelay(1);
> +		gayle.intreq = tmp;
> +		mdelay(300);
> +	}
> +
>  	pcmcia_reset();
>  	pcmcia_program_voltage(PCMCIA_0V);
>  	pcmcia_access_speed(PCMCIA_SPEED_250NS);
> 

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19  0:56   ` Finn Thain
@ 2021-06-19  3:13     ` Michael Schmitz
  0 siblings, 0 replies; 9+ messages in thread
From: Michael Schmitz @ 2021-06-19  3:13 UTC (permalink / raw)
  To: Finn Thain; +Cc: linux-m68k, geert, alex, netdev

Hi Finn,

thanks for reviewing again!

Am 19.06.2021 um 12:56 schrieb Finn Thain:
>>
>> +	/* Reset card. Who knows what dain-bramaged state it was left in. */
>> +	{	unsigned long reset_start_time = jiffies;
>
> There's a missing line break here.

Straight copy from apne_probe1() below, but you're right about style of 
course.

>
>> +
>> +		outb(inb(IOBASE + NE_RESET), IOBASE + NE_RESET);
>> +
>> +		while ((inb(IOBASE + NE_EN0_ISR) & ENISR_RESET) == 0)
>> +			if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
>
> You could use msecs_to_jiffies(20) here.
>
>> +				pr_info("Card not found (no reset ack).\n");
>> +				isa_type=ISA_TYPE_AG16;
>
> Whitespace is needed around the '='.
>
>> +			}
>
> Missing a break statement?

Ouch.

>
>> +
>> +		outb(0xff, IOBASE + NE_EN0_ISR);		/* Ack all intr. */
>> +	}
>> +
>>  	dev = alloc_ei_netdev();
>>  	if (!dev)
>>  		return ERR_PTR(-ENOMEM);
>> @@ -590,6 +613,16 @@ static int init_pcmcia(void)
>>  #endif
>>  	u_long offset;
>>
>> +	/* reset card (idea taken from CardReset by Artur Pogoda) */
>> +	if (isa_type == ISA_TYPE_AG16) {
>> +		u_char  tmp = gayle.intreq;
>> +
>
> Extra whitespace.
>
>> +		gayle.intreq = 0xff;
>> +		mdelay(1);
>> +		gayle.intreq = tmp;
>> +		mdelay(300);
>> +	}
>> +
>>  	pcmcia_reset();
>>  	pcmcia_program_voltage(PCMCIA_0V);
>>  	pcmcia_access_speed(PCMCIA_SPEED_250NS);
>>

Thanks, will fix in v6 (and correct the commit message). Might split off 
the autoprobe bit so that can be easily dropped if need be.

Cheers,

	Michael

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19  0:34 ` [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver Michael Schmitz
  2021-06-19  0:56   ` Finn Thain
@ 2021-06-19  9:08   ` Geert Uytterhoeven
  2021-06-19 19:31     ` Michael Schmitz
  1 sibling, 1 reply; 9+ messages in thread
From: Geert Uytterhoeven @ 2021-06-19  9:08 UTC (permalink / raw)
  To: Michael Schmitz; +Cc: Linux/m68k, ALeX Kazik, netdev

Hi Michael,

On Sat, Jun 19, 2021 at 2:35 AM Michael Schmitz <schmitzmic@gmail.com> wrote:
> Add Kconfig option, module parameter and PCMCIA reset code
> required to support 100 Mbit PCMCIA ethernet cards on Amiga.
>
> 10 Mbit and 100 Mbit mode are supported by the same module.
> A module parameter switches Amiga ISA IO accessors to word
> access by changing isa_type at runtime. Additional code to
> reset the PCMCIA hardware is also added to the driver probe.
>
> Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
> 100 MBit card support" submitted to netdev 2018/09/16 by Alex
> Kazik <alex@kazik.de>.
>
> CC: netdev@vger.kernel.org
> Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
> Tested-by: Alex Kazik <alex@kazik.de>
> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

Thanks for your patch!

Note that this patch has a hard dependency on "[PATCH v5 1/2] m68k:
io_mm.h - add APNE 100 MBit support" in the series, so it must not
be applied to the netdev tree yet.

> --- a/drivers/net/ethernet/8390/Kconfig
> +++ b/drivers/net/ethernet/8390/Kconfig
> @@ -143,6 +143,10 @@ config APNE
>           To compile this driver as a module, choose M here: the module
>           will be called apne.
>
> +         The driver also supports 10/100Mbit cards (e.g. Netgear FA411,
> +         CNet Singlepoint). To activate 100 Mbit support at runtime or
> +         from the kernel command line, use the apne.100mbit module parameter.

According to the recent discussion about that, "at runtime" is not
really possible?  So that limits it to kernel command line (for the
builtin case)
or module parameter (for the modular case).

> +
>  config PCMCIA_PCNET
>         tristate "NE2000 compatible PCMCIA support"
>         depends on PCMCIA
> diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
> index fe6c834..8223e15 100644
> --- a/drivers/net/ethernet/8390/apne.c
> +++ b/drivers/net/ethernet/8390/apne.c
> @@ -120,6 +120,10 @@ static u32 apne_msg_enable;
>  module_param_named(msg_enable, apne_msg_enable, uint, 0444);
>  MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
>
> +static bool apne_100_mbit;
> +module_param_named(100_mbit, apne_100_mbit, bool, 0644);
> +MODULE_PARM_DESC(100_mbit, "Enable 100 Mbit support");

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19  9:08   ` Geert Uytterhoeven
@ 2021-06-19 19:31     ` Michael Schmitz
  2021-06-20 11:47       ` Geert Uytterhoeven
  0 siblings, 1 reply; 9+ messages in thread
From: Michael Schmitz @ 2021-06-19 19:31 UTC (permalink / raw)
  To: Geert Uytterhoeven; +Cc: Linux/m68k, ALeX Kazik, netdev

Hi Geert,

thanks for your review!

Am 19.06.2021 um 21:08 schrieb Geert Uytterhoeven:
> Hi Michael,
>
> On Sat, Jun 19, 2021 at 2:35 AM Michael Schmitz <schmitzmic@gmail.com> wrote:
>> Add Kconfig option, module parameter and PCMCIA reset code
>> required to support 100 Mbit PCMCIA ethernet cards on Amiga.
>>
>> 10 Mbit and 100 Mbit mode are supported by the same module.
>> A module parameter switches Amiga ISA IO accessors to word
>> access by changing isa_type at runtime. Additional code to
>> reset the PCMCIA hardware is also added to the driver probe.
>>
>> Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
>> 100 MBit card support" submitted to netdev 2018/09/16 by Alex
>> Kazik <alex@kazik.de>.
>>
>> CC: netdev@vger.kernel.org
>> Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
>> Tested-by: Alex Kazik <alex@kazik.de>
>> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
>
> Thanks for your patch!
>
> Note that this patch has a hard dependency on "[PATCH v5 1/2] m68k:
> io_mm.h - add APNE 100 MBit support" in the series, so it must not
> be applied to the netdev tree yet.

Hmm - so we ought to protect the new code by

#ifdef ARCH_HAVE_16BIT_PCMCIA

and set that in the m68k machine Kconfig in the first patch?

(It's almost, but not quite like a config option :-)

>
>> --- a/drivers/net/ethernet/8390/Kconfig
>> +++ b/drivers/net/ethernet/8390/Kconfig
>> @@ -143,6 +143,10 @@ config APNE
>>           To compile this driver as a module, choose M here: the module
>>           will be called apne.
>>
>> +         The driver also supports 10/100Mbit cards (e.g. Netgear FA411,
>> +         CNet Singlepoint). To activate 100 Mbit support at runtime or
>> +         from the kernel command line, use the apne.100mbit module parameter.
>
> According to the recent discussion about that, "at runtime" is not
> really possible?  So that limits it to kernel command line (for the
> builtin case)
> or module parameter (for the modular case).

True - I'll reword that.

Cheers,

	Michael

>
>> +
>>  config PCMCIA_PCNET
>>         tristate "NE2000 compatible PCMCIA support"
>>         depends on PCMCIA
>> diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
>> index fe6c834..8223e15 100644
>> --- a/drivers/net/ethernet/8390/apne.c
>> +++ b/drivers/net/ethernet/8390/apne.c
>> @@ -120,6 +120,10 @@ static u32 apne_msg_enable;
>>  module_param_named(msg_enable, apne_msg_enable, uint, 0444);
>>  MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
>>
>> +static bool apne_100_mbit;
>> +module_param_named(100_mbit, apne_100_mbit, bool, 0644);
>> +MODULE_PARM_DESC(100_mbit, "Enable 100 Mbit support");
>
> Gr{oetje,eeting}s,
>
>                         Geert
>

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-19 19:31     ` Michael Schmitz
@ 2021-06-20 11:47       ` Geert Uytterhoeven
  2021-06-20 19:36         ` Michael Schmitz
  0 siblings, 1 reply; 9+ messages in thread
From: Geert Uytterhoeven @ 2021-06-20 11:47 UTC (permalink / raw)
  To: Michael Schmitz; +Cc: Linux/m68k, ALeX Kazik, netdev

Hi Michael,

On Sat, Jun 19, 2021 at 9:31 PM Michael Schmitz <schmitzmic@gmail.com> wrote:
> Am 19.06.2021 um 21:08 schrieb Geert Uytterhoeven:
> > On Sat, Jun 19, 2021 at 2:35 AM Michael Schmitz <schmitzmic@gmail.com> wrote:
> >> Add Kconfig option, module parameter and PCMCIA reset code
> >> required to support 100 Mbit PCMCIA ethernet cards on Amiga.
> >>
> >> 10 Mbit and 100 Mbit mode are supported by the same module.
> >> A module parameter switches Amiga ISA IO accessors to word
> >> access by changing isa_type at runtime. Additional code to
> >> reset the PCMCIA hardware is also added to the driver probe.
> >>
> >> Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
> >> 100 MBit card support" submitted to netdev 2018/09/16 by Alex
> >> Kazik <alex@kazik.de>.
> >>
> >> CC: netdev@vger.kernel.org
> >> Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
> >> Tested-by: Alex Kazik <alex@kazik.de>
> >> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
> >
> > Thanks for your patch!
> >
> > Note that this patch has a hard dependency on "[PATCH v5 1/2] m68k:
> > io_mm.h - add APNE 100 MBit support" in the series, so it must not
> > be applied to the netdev tree yet.
>
> Hmm - so we ought to protect the new code by
>
> #ifdef ARCH_HAVE_16BIT_PCMCIA
>
> and set that in the m68k machine Kconfig in the first patch?
>
> (It's almost, but not quite like a config option :-)

No, we just manage dependencies, so either:
  1. Patch 2 cannot go in until patch 1 is upstream,
  2. One subsystem maintainer gives an Acked-by for one patch,so
    the other subsystem maintainer can apply both patches.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver
  2021-06-20 11:47       ` Geert Uytterhoeven
@ 2021-06-20 19:36         ` Michael Schmitz
  0 siblings, 0 replies; 9+ messages in thread
From: Michael Schmitz @ 2021-06-20 19:36 UTC (permalink / raw)
  To: Geert Uytterhoeven; +Cc: Linux/m68k, ALeX Kazik, netdev

Hi Geert,

On 20/06/21 11:47 pm, Geert Uytterhoeven wrote:
>
>>> Thanks for your patch!
>>>
>>> Note that this patch has a hard dependency on "[PATCH v5 1/2] m68k:
>>> io_mm.h - add APNE 100 MBit support" in the series, so it must not
>>> be applied to the netdev tree yet.
>> Hmm - so we ought to protect the new code by
>>
>> #ifdef ARCH_HAVE_16BIT_PCMCIA
>>
>> and set that in the m68k machine Kconfig in the first patch?
>>
>> (It's almost, but not quite like a config option :-)
> No, we just manage dependencies, so either:
>    1. Patch 2 cannot go in until patch 1 is upstream,
>    2. One subsystem maintainer gives an Acked-by for one patch,so
>      the other subsystem maintainer can apply both patches.

I haven't had any review from netdev yet - option 1 looks more feasible 
(if you want to carry a patch that's useless without its follow-up). And 
with the autoprobe failing (if I understood Alex right), I'll have to 
think of something else or drop that patch again.

Is there anything (aside from linking to the e-mail thread) that I can 
do to help netdev maintainers locate the first patch? The commit ID 
won't remain the same once accepted upstream, am I right?

Cheers,

     Michael

>
> Gr{oetje,eeting}s,
>
>                          Geert
>

^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, other threads:[~2021-06-20 19:36 UTC | newest]

Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-19  0:34 [PATCH v5 0/2] Add APNE PCMCIA 100 Mbit support Michael Schmitz
2021-06-19  0:34 ` [PATCH v5 1/2] m68k: io_mm.h - add APNE 100 MBit support Michael Schmitz
2021-06-19  0:34 ` [PATCH net-next v5 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver Michael Schmitz
2021-06-19  0:56   ` Finn Thain
2021-06-19  3:13     ` Michael Schmitz
2021-06-19  9:08   ` Geert Uytterhoeven
2021-06-19 19:31     ` Michael Schmitz
2021-06-20 11:47       ` Geert Uytterhoeven
2021-06-20 19:36         ` Michael Schmitz

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.