* [PATCH V7] PCI: rcar: Add L1 link state fix into data abort hook
@ 2021-08-15 18:16 marek.vasut
2021-08-16 13:57 ` Lorenzo Pieralisi
0 siblings, 1 reply; 2+ messages in thread
From: marek.vasut @ 2021-08-15 18:16 UTC (permalink / raw)
To: linux-pci
Cc: Marek Vasut, Bjorn Helgaas, Geert Uytterhoeven,
Lorenzo Pieralisi, Wolfram Sang, Yoshihiro Shimoda,
linux-renesas-soc
From: Marek Vasut <marek.vasut+renesas@gmail.com>
When the link is in L1, hardware should return it to L0
automatically whenever a transaction targets a component on the
other end of the link (PCIe r5.0, sec 5.2).
The R-Car PCIe controller doesn't handle this transition correctly.
If the link is not in L0, an MMIO transaction targeting a downstream
device fails, and the controller reports an ARM imprecise external
abort.
Work around this by hooking the abort handler so the driver can
detect this situation and help the hardware complete the link state
transition.
When the R-Car controller receives a PM_ENTER_L1 DLLP from the
downstream component, it sets PMEL1RX bit in PMSR register, but then
the controller enters some sort of in-between state. A subsequent
MMIO transaction will fail, resulting in the external abort. The
abort handler detects this condition and completes the link state
transition by setting the L1IATN bit in PMCTLR and waiting for the
link state transition to complete.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
---
V2: - Update commit message, add link to TFA repository commit
- Handle the LPAE case as in ARM fault.c and fsr-{2,3}level.c
- Cache clock and check whether they are enabled before register
access
V3: - Fix commit message according to spellchecker
- Use of_find_matching_node() to apply hook only on Gen1 and Gen2 RCar
(in case the kernel is multiplatform)
V4: - Mark rcar_pcie_abort_handler_of_match with __initconst
V5: - Add mutex around rcar_pcie_aarch32_abort_handler()
- Update commit message again to point out issues with L1/D3Hot states
V6: - Return 1 only if condition cannot be fixed
V7: - Replace commit message by one provided by upstream, verbatim
- Use readl_poll_timeout_atomic() to poll for L1FAEG bit with timeout
---
drivers/pci/controller/pcie-rcar-host.c | 86 +++++++++++++++++++++++++
drivers/pci/controller/pcie-rcar.h | 7 ++
2 files changed, 93 insertions(+)
diff --git a/drivers/pci/controller/pcie-rcar-host.c b/drivers/pci/controller/pcie-rcar-host.c
index 00a8267eda14..8f3131844e77 100644
--- a/drivers/pci/controller/pcie-rcar-host.c
+++ b/drivers/pci/controller/pcie-rcar-host.c
@@ -13,12 +13,14 @@
#include <linux/bitops.h>
#include <linux/clk.h>
+#include <linux/clk-provider.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/iopoll.h>
#include <linux/msi.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
@@ -41,6 +43,21 @@ struct rcar_msi {
int irq2;
};
+#ifdef CONFIG_ARM
+/*
+ * Here we keep a static copy of the remapped PCIe controller address.
+ * This is only used on aarch32 systems, all of which have one single
+ * PCIe controller, to provide quick access to the PCIe controller in
+ * the L1 link state fixup function, called from the ARM fault handler.
+ */
+static void __iomem *pcie_base;
+/*
+ * Static copy of bus clock pointer, so we can check whether the clock
+ * is enabled or not.
+ */
+static struct clk *pcie_bus_clk;
+#endif
+
/* Structure representing the PCIe interface */
struct rcar_pcie_host {
struct rcar_pcie pcie;
@@ -774,6 +791,12 @@ static int rcar_pcie_get_resources(struct rcar_pcie_host *host)
}
host->msi.irq2 = i;
+#ifdef CONFIG_ARM
+ /* Cache static copy for L1 link state fixup hook on aarch32 */
+ pcie_base = pcie->base;
+ pcie_bus_clk = host->bus_clk;
+#endif
+
return 0;
err_irq2:
@@ -1029,4 +1052,67 @@ static struct platform_driver rcar_pcie_driver = {
},
.probe = rcar_pcie_probe,
};
+
+#ifdef CONFIG_ARM
+static DEFINE_SPINLOCK(pmsr_lock);
+static int rcar_pcie_aarch32_abort_handler(unsigned long addr,
+ unsigned int fsr, struct pt_regs *regs)
+{
+ unsigned long flags;
+ u32 pmsr, val;
+ int ret = 0;
+
+ spin_lock_irqsave(&pmsr_lock, flags);
+
+ if (!pcie_base || !__clk_is_enabled(pcie_bus_clk)) {
+ ret = 1;
+ goto unlock_exit;
+ }
+
+ pmsr = readl(pcie_base + PMSR);
+
+ /*
+ * Test if the PCIe controller received PM_ENTER_L1 DLLP and
+ * the PCIe controller is not in L1 link state. If true, apply
+ * fix, which will put the controller into L1 link state, from
+ * which it can return to L0s/L0 on its own.
+ */
+ if ((pmsr & PMEL1RX) && ((pmsr & PMSTATE) != PMSTATE_L1)) {
+ writel(L1IATN, pcie_base + PMCTLR);
+ ret = readl_poll_timeout_atomic(pcie_base + PMSR, val,
+ val & L1FAEG, 10, 1000);
+ WARN(ret, "Timeout waiting for L1 link state, ret=%d\n", ret);
+ writel(L1FAEG | PMEL1RX, pcie_base + PMSR);
+ }
+
+unlock_exit:
+ spin_unlock_irqrestore(&pmsr_lock, flags);
+ return ret;
+}
+
+static const struct of_device_id rcar_pcie_abort_handler_of_match[] __initconst = {
+ { .compatible = "renesas,pcie-r8a7779" },
+ { .compatible = "renesas,pcie-r8a7790" },
+ { .compatible = "renesas,pcie-r8a7791" },
+ { .compatible = "renesas,pcie-rcar-gen2" },
+ {},
+};
+
+static int __init rcar_pcie_init(void)
+{
+ if (of_find_matching_node(NULL, rcar_pcie_abort_handler_of_match)) {
+#ifdef CONFIG_ARM_LPAE
+ hook_fault_code(17, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+ "asynchronous external abort");
+#else
+ hook_fault_code(22, rcar_pcie_aarch32_abort_handler, SIGBUS, 0,
+ "imprecise external abort");
+#endif
+ }
+
+ return platform_driver_register(&rcar_pcie_driver);
+}
+device_initcall(rcar_pcie_init);
+#else
builtin_platform_driver(rcar_pcie_driver);
+#endif
diff --git a/drivers/pci/controller/pcie-rcar.h b/drivers/pci/controller/pcie-rcar.h
index d4c698b5f821..9bb125db85c6 100644
--- a/drivers/pci/controller/pcie-rcar.h
+++ b/drivers/pci/controller/pcie-rcar.h
@@ -85,6 +85,13 @@
#define LTSMDIS BIT(31)
#define MACCTLR_INIT_VAL (LTSMDIS | MACCTLR_NFTS_MASK)
#define PMSR 0x01105c
+#define L1FAEG BIT(31)
+#define PMEL1RX BIT(23)
+#define PMSTATE GENMASK(18, 16)
+#define PMSTATE_L1 (3 << 16)
+#define PMCTLR 0x011060
+#define L1IATN BIT(31)
+
#define MACS2R 0x011078
#define MACCGSPSETR 0x011084
#define SPCNGRSN BIT(31)
--
2.30.2
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH V7] PCI: rcar: Add L1 link state fix into data abort hook
2021-08-15 18:16 [PATCH V7] PCI: rcar: Add L1 link state fix into data abort hook marek.vasut
@ 2021-08-16 13:57 ` Lorenzo Pieralisi
0 siblings, 0 replies; 2+ messages in thread
From: Lorenzo Pieralisi @ 2021-08-16 13:57 UTC (permalink / raw)
To: linux-pci, marek.vasut
Cc: Lorenzo Pieralisi, linux-renesas-soc, Bjorn Helgaas,
Geert Uytterhoeven, Wolfram Sang, Yoshihiro Shimoda, Marek Vasut
On Sun, 15 Aug 2021 20:16:50 +0200, marek.vasut@gmail.com wrote:
> When the link is in L1, hardware should return it to L0
> automatically whenever a transaction targets a component on the
> other end of the link (PCIe r5.0, sec 5.2).
>
> The R-Car PCIe controller doesn't handle this transition correctly.
> If the link is not in L0, an MMIO transaction targeting a downstream
> device fails, and the controller reports an ARM imprecise external
> abort.
>
> [...]
Applied to pci/rcar, thanks!
[1/1] PCI: rcar: Add L1 link state fix into data abort hook
https://git.kernel.org/lpieralisi/pci/c/a115b1bd3a
Thanks,
Lorenzo
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2021-08-16 14:00 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-08-15 18:16 [PATCH V7] PCI: rcar: Add L1 link state fix into data abort hook marek.vasut
2021-08-16 13:57 ` Lorenzo Pieralisi
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.