From: Yang Xu <xuyang2018.jy@fujitsu.com>
To: <ltp@lists.linux.it>
Subject: [LTP] [PATCH v5 2/4] zram/zram_lib.sh: adapt the situation that zram device is being used
Date: Mon, 20 Dec 2021 14:52:20 +0800 [thread overview]
Message-ID: <1639983142-2247-2-git-send-email-xuyang2018.jy@fujitsu.com> (raw)
In-Reply-To: <1639983142-2247-1-git-send-email-xuyang2018.jy@fujitsu.com>
If zram-generator package is installed and works, then we can not remove zram module
because zram swap is being used. This case needs a clean zram environment, change this
test by using hot_add/hot_remove interface[1]. So even zram device is being used, we
still can add zram device and remove them in cleanup.
The two interface was introduced since kernel commit 6566d1a32("zram: add dynamic
device add/remove functionality")[2] in 2015.6. If kernel supports these two interface,
we use hot_add/hot_remove to slove this problem, if not, just check whether zram is
being used or built in, then skip it on old kernel.
Also, zram01,02 case are adjuested to adapt the situation that CONFIG_ZRAM=y and can
run zram01,02 simultaneously on new kernel.
[1]https://www.kernel.org/doc/html/latest/admin-guide/blockdev/zram.html#add-remove-zram-devices
[2]https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6566d1a32bf7
Fixes: #888
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
---
.../kernel/device-drivers/zram/zram01.sh | 6 +-
.../kernel/device-drivers/zram/zram02.sh | 4 +-
.../kernel/device-drivers/zram/zram_lib.sh | 78 +++++++++++++------
3 files changed, 60 insertions(+), 28 deletions(-)
diff --git a/testcases/kernel/device-drivers/zram/zram01.sh b/testcases/kernel/device-drivers/zram/zram01.sh
index ad9a9a2be..5e13f387c 100755
--- a/testcases/kernel/device-drivers/zram/zram01.sh
+++ b/testcases/kernel/device-drivers/zram/zram01.sh
@@ -69,7 +69,7 @@ setup()
zram_makefs()
{
- local i=0
+ local i=$dev_start
local fs
for fs in $zram_filesystems; do
@@ -90,7 +90,7 @@ zram_mount()
{
local i=0
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
tst_res TINFO "mount /dev/zram$i"
mkdir zram$i
ROD mount /dev/zram$i zram$i
@@ -102,7 +102,7 @@ zram_mount()
zram_fill_fs()
{
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
tst_res TINFO "filling zram$i (it can take long time)"
local b=0
while true; do
diff --git a/testcases/kernel/device-drivers/zram/zram02.sh b/testcases/kernel/device-drivers/zram/zram02.sh
index f0421ce7f..c980fce76 100755
--- a/testcases/kernel/device-drivers/zram/zram02.sh
+++ b/testcases/kernel/device-drivers/zram/zram02.sh
@@ -29,7 +29,7 @@ zram_makeswap()
tst_require_cmds mkswap swapon swapoff
local i=0
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
ROD mkswap /dev/zram$i
ROD swapon /dev/zram$i
tst_res TINFO "done with /dev/zram$i"
@@ -44,7 +44,7 @@ zram_swapoff()
tst_require_cmds swapoff
local i
- for i in $(seq 0 $dev_makeswap); do
+ for i in $(seq $dev_start $dev_end); do
ROD swapoff /dev/zram$i
done
dev_makeswap=-1
diff --git a/testcases/kernel/device-drivers/zram/zram_lib.sh b/testcases/kernel/device-drivers/zram/zram_lib.sh
index fe9c915c3..84a9a4378 100755
--- a/testcases/kernel/device-drivers/zram/zram_lib.sh
+++ b/testcases/kernel/device-drivers/zram/zram_lib.sh
@@ -5,6 +5,10 @@
dev_makeswap=-1
dev_mounted=-1
+dev_start=0
+dev_end=-1
+module_load=-1
+sys_control=-1
TST_NEEDS_TMPDIR=1
TST_NEEDS_ROOT=1
@@ -17,19 +21,27 @@ zram_cleanup()
{
local i
- for i in $(seq 0 $dev_makeswap); do
+ for i in $(seq $dev_start $dev_makeswap); do
swapoff /dev/zram$i
done
- for i in $(seq 0 $dev_mounted); do
+ for i in $(seq $dev_start $dev_mounted); do
umount /dev/zram$i
done
- for i in $(seq 0 $(($dev_num - 1))); do
+ for i in $(seq $dev_start $dev_end); do
echo 1 > /sys/block/zram${i}/reset
done
- rmmod zram > /dev/null 2>&1
+ if [ $sys_control -eq 1 ]; then
+ for i in $(seq $dev_start $dev_end); do
+ echo $i > /sys/class/zram-control/hot_remove
+ done
+ fi
+
+ if [ $module_load -eq 1 ]; then
+ rmmod zram > /dev/null 2>&1
+ fi
}
zram_load()
@@ -51,16 +63,38 @@ zram_load()
tst_res TINFO "create '$dev_num' zram device(s)"
- modprobe zram num_devices=$dev_num || \
- tst_brk TBROK "failed to insert zram module"
+# On kernel that supports /sys/class/zram-control interface but doesn't load zram,
+# we dont' need to use hot_add/hot_remove interface. If system has loaded zram
+# or buitin, we need to use hot_add/hot_remove interface.
+# On old kernel that doesn't support /sys/class/zram-control interface, we just
+# check whether zram module is being used or it is built in kernel(we can't create
+# number of devices required). If so, skip it.
+ if [ ! -d "/sys/class/zram-control" ]; then
+ modprobe zram num_devices=$dev_num
+ if [ ! -d "/sys/class/zram-control" ]; then
+ if grep -q '^zram' /proc/modules; then
+ rmmod zram > /dev/null 2>&1 || \
+ tst_brk TCONF "zram module is being used"
+ else
+ tst_brk TCONF "test needs CONFIG_ZRAM=m"
+ fi
+ modprobe zram num_devices=$dev_num
+ fi
+ module_load=1
+ dev_end=$(($dev_num - 1))
+ tst_res TPASS "all zram devices (/dev/zram0~$dev_end) successfully created"
+ return
+ fi
- dev_num_created=$(ls /dev/zram* | wc -w)
+ dev_start=$(ls /dev/zram* | wc -w)
+ dev_end=$(($dev_start + $dev_num - 1))
+ sys_control=1
- if [ "$dev_num_created" -ne "$dev_num" ]; then
- tst_brk TFAIL "unexpected num of devices: $dev_num_created"
- fi
+ for i in $(seq $dev_start $dev_end); do
+ cat /sys/class/zram-control/hot_add > /dev/null
+ done
- tst_res TPASS "all zram devices successfully created"
+ tst_res TPASS "all zram devices (/dev/zram$dev_start~$dev_end) successfully created"
}
zram_max_streams()
@@ -73,7 +107,7 @@ zram_max_streams()
tst_res TINFO "set max_comp_streams to zram device(s)"
- local i=0
+ local i=$dev_start
for max_s in $zram_max_streams; do
local sys_path="/sys/block/zram${i}/max_comp_streams"
@@ -85,7 +119,7 @@ zram_max_streams()
tst_brk TFAIL "can't set max_streams '$max_s', get $max_stream"
i=$(($i + 1))
- tst_res TINFO "$sys_path = '$max_streams' ($i/$dev_num)"
+ tst_res TINFO "$sys_path = '$max_streams'"
done
tst_res TPASS "test succeeded"
@@ -100,20 +134,18 @@ zram_compress_alg()
return
fi
- local i=0
+ local i=$dev_start
tst_res TINFO "test that we can set compression algorithm"
- local algs="$(sed 's/[][]//g' /sys/block/zram0/comp_algorithm)"
+ local algs="$(sed 's/[][]//g' /sys/block/zram${i}/comp_algorithm)"
tst_res TINFO "supported algs: $algs"
- local dev_max=$(($dev_num - 1))
-
- for i in $(seq 0 $dev_max); do
+ for i in $(seq $dev_start $dev_end); do
for alg in $algs; do
local sys_path="/sys/block/zram${i}/comp_algorithm"
echo "$alg" > $sys_path || \
tst_brk TFAIL "can't set '$alg' to $sys_path"
- tst_res TINFO "$sys_path = '$alg' ($i/$dev_max)"
+ tst_res TINFO "$sys_path = '$alg'"
done
done
@@ -122,7 +154,7 @@ zram_compress_alg()
zram_set_disksizes()
{
- local i=0
+ local i=$dev_start
local ds
tst_res TINFO "set disk size to zram device(s)"
@@ -132,7 +164,7 @@ zram_set_disksizes()
tst_brk TFAIL "can't set '$ds' to $sys_path"
i=$(($i + 1))
- tst_res TINFO "$sys_path = '$ds' ($i/$dev_num)"
+ tst_res TINFO "$sys_path = '$ds'"
done
tst_res TPASS "test succeeded"
@@ -147,7 +179,7 @@ zram_set_memlimit()
return
fi
- local i=0
+ local i=$dev_start
local ds
tst_res TINFO "set memory limit to zram device(s)"
@@ -158,7 +190,7 @@ zram_set_memlimit()
tst_brk TFAIL "can't set '$ds' to $sys_path"
i=$(($i + 1))
- tst_res TINFO "$sys_path = '$ds' ($i/$dev_num)"
+ tst_res TINFO "$sys_path = '$ds'"
done
tst_res TPASS "test succeeded"
--
2.23.0
--
Mailing list info: https://lists.linux.it/listinfo/ltp
next prev parent reply other threads:[~2021-12-20 6:53 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-20 6:52 [LTP] [PATCH v5 1/4] swapping01: skip test if zram-swap is being used Yang Xu
2021-12-20 6:52 ` Yang Xu [this message]
2021-12-20 10:45 ` [LTP] [PATCH v5 2/4] zram/zram_lib.sh: adapt the situation that zram device " Petr Vorel
2021-12-21 1:33 ` xuyang2018.jy
2021-12-20 6:52 ` [LTP] [PATCH v5 3/4] zram/zram03: Convert into new api Yang Xu
2021-12-20 6:52 ` [LTP] [PATCH v5 4/4] zram/zram01.sh: replacing data stored in this disk with allocated for this disk Yang Xu
2021-12-20 10:49 ` Petr Vorel
2021-12-21 2:18 ` xuyang2018.jy
2021-12-21 8:41 ` Petr Vorel
2021-12-22 9:33 ` xuyang2018.jy
2021-12-22 14:12 ` Petr Vorel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1639983142-2247-2-git-send-email-xuyang2018.jy@fujitsu.com \
--to=xuyang2018.jy@fujitsu.com \
--cc=ltp@lists.linux.it \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.