* [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra
@ 2023-01-19 13:44 Neil Armstrong
2023-01-19 13:44 ` [PATCH 1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1 Neil Armstrong
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-19 13:44 UTC (permalink / raw)
To: u-boot, u-boot-amlogic, Neil Armstrong
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
- Power Halt
Cc: u-boot@lists.denx.de
Cc: u-boot-amlogic@groups.io
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Neil Armstrong (2):
ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1
ARM: meson: add support for Odroid Go Ultra
arch/arm/dts/Makefile | 1 +
arch/arm/dts/meson-g12-common.dtsi | 167 +++--
arch/arm/dts/meson-g12a.dtsi | 5 +
.../arm/dts/meson-g12b-odroid-go-ultra-u-boot.dtsi | 16 +
arch/arm/dts/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
arch/arm/dts/meson-g12b.dtsi | 5 +
arch/arm/dts/meson-sm1.dtsi | 52 +-
configs/odroid-go-ultra_defconfig | 70 ++
doc/board/amlogic/index.rst | 4 +-
doc/board/amlogic/odroid-go-ultra.rst | 34 +
10 files changed, 999 insertions(+), 77 deletions(-)
---
base-commit: 62e2ad1ceafbfdf2c44d3dc1b6efc81e768a96b9
change-id: 20230119-u-boot-odroid-go-ultra-9d3c7ae3c910
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1
2023-01-19 13:44 [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra Neil Armstrong
@ 2023-01-19 13:44 ` Neil Armstrong
2023-01-19 13:44 ` [PATCH 2/2] ARM: meson: add support for Odroid Go Ultra Neil Armstrong
2023-01-24 8:25 ` [PATCH 0/2] ARM: arch-meson: " Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-19 13:44 UTC (permalink / raw)
To: u-boot, u-boot-amlogic, Neil Armstrong
This syncs the Amlogic G12A, G12B & SM1 base DT + the
Odroid Go Ultra DT from Linux v6.2-rc1 from commmit [1].
[1] 1b929c02afd3 ("Linux 6.2-rc1")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/meson-g12-common.dtsi | 167 ++++---
arch/arm/dts/meson-g12a.dtsi | 5 +
arch/arm/dts/meson-g12b-odroid-go-ultra.dts | 722 ++++++++++++++++++++++++++++
arch/arm/dts/meson-g12b.dtsi | 5 +
arch/arm/dts/meson-sm1.dtsi | 52 +-
6 files changed, 876 insertions(+), 76 deletions(-)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 43951a7731..fc43e953e6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -198,6 +198,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
meson-g12b-gtking.dtb \
meson-g12b-gtking-pro.dtb \
meson-g12b-gsking-x.dtb \
+ meson-g12b-odroid-go-ultra.dtb \
meson-g12b-odroid-n2.dtb \
meson-g12b-odroid-n2-plus.dtb \
meson-sm1-bananapi-m5.dtb \
diff --git a/arch/arm/dts/meson-g12-common.dtsi b/arch/arm/dts/meson-g12-common.dtsi
index 00c6f53290..9dbd50820b 100644
--- a/arch/arm/dts/meson-g12-common.dtsi
+++ b/arch/arm/dts/meson-g12-common.dtsi
@@ -58,7 +58,7 @@
secure-monitor = <&sm>;
};
- gpu_opp_table: gpu-opp-table {
+ gpu_opp_table: opp-table-gpu {
compatible = "operating-points-v2";
opp-124999998 {
@@ -107,6 +107,12 @@
no-map;
};
+ /* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+ secmon_reserved_bl32: secmon@5300000 {
+ reg = <0x0 0x05300000 0x0 0x2000000>;
+ no-map;
+ };
+
linux,cma {
compatible = "shared-dma-pool";
reusable;
@@ -159,61 +165,6 @@
status = "disabled";
};
- thermal-zones {
- cpu_thermal: cpu-thermal {
- polling-delay = <1000>;
- polling-delay-passive = <100>;
- thermal-sensors = <&cpu_temp>;
-
- trips {
- cpu_passive: cpu-passive {
- temperature = <85000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "passive";
- };
-
- cpu_hot: cpu-hot {
- temperature = <95000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "hot";
- };
-
- cpu_critical: cpu-critical {
- temperature = <110000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "critical";
- };
- };
- };
-
- ddr_thermal: ddr-thermal {
- polling-delay = <1000>;
- polling-delay-passive = <100>;
- thermal-sensors = <&ddr_temp>;
-
- trips {
- ddr_passive: ddr-passive {
- temperature = <85000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "passive";
- };
-
- ddr_critical: ddr-critical {
- temperature = <110000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "critical";
- };
- };
-
- cooling-maps {
- map {
- trip = <&ddr_passive>;
- cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
- };
- };
-
ethmac: ethernet@ff3f0000 {
compatible = "amlogic,meson-g12a-dwmac",
"snps,dwmac-3.70a",
@@ -894,6 +845,22 @@
};
};
+ pwm_f_z_pins: pwm-f-z {
+ mux {
+ groups = "pwm_f_z";
+ function = "pwm_f";
+ bias-disable;
+ };
+ };
+
+ pwm_f_a_pins: pwm-f-a {
+ mux {
+ groups = "pwm_f_a";
+ function = "pwm_f";
+ bias-disable;
+ };
+ };
+
pwm_f_x_pins: pwm-f-x {
mux {
groups = "pwm_f_x";
@@ -1738,6 +1705,12 @@
};
};
+ pmu: pmu@ff638000 {
+ reg = <0x0 0xff638000 0x0 0x100>,
+ <0x0 0xff638c00 0x0 0x100>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>;
+ };
+
aobus: bus@ff800000 {
compatible = "simple-bus";
reg = <0x0 0xff800000 0x0 0x100000>;
@@ -1936,6 +1909,33 @@
};
};
+ uart_ao_b_2_3_pins: uart-ao-b-2-3 {
+ mux {
+ groups = "uart_ao_b_tx_2",
+ "uart_ao_b_rx_3";
+ function = "uart_ao_b";
+ bias-disable;
+ };
+ };
+
+ uart_ao_b_8_9_pins: uart-ao-b-8-9 {
+ mux {
+ groups = "uart_ao_b_tx_8",
+ "uart_ao_b_rx_9";
+ function = "uart_ao_b";
+ bias-disable;
+ };
+ };
+
+ uart_ao_b_cts_rts_pins: uart-ao-b-cts-rts {
+ mux {
+ groups = "uart_ao_b_cts",
+ "uart_ao_b_rts";
+ function = "uart_ao_b";
+ bias-disable;
+ };
+ };
+
pwm_a_e_pins: pwm-a-e {
mux {
groups = "pwm_a_e";
@@ -2415,6 +2415,61 @@
};
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&cpu_temp>;
+
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ ddr_thermal: ddr-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&ddr_temp>;
+
+ trips {
+ ddr_passive: ddr-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ddr_critical: ddr-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_passive>;
+ cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
diff --git a/arch/arm/dts/meson-g12a.dtsi b/arch/arm/dts/meson-g12a.dtsi
index fb0ab27d1f..7677764eee 100644
--- a/arch/arm/dts/meson-g12a.dtsi
+++ b/arch/arm/dts/meson-g12a.dtsi
@@ -50,6 +50,7 @@
l2: l2-cache0 {
compatible = "cache";
+ cache-level = <2>;
};
};
@@ -133,3 +134,7 @@
};
};
};
+
+&pmu {
+ compatible = "amlogic,g12a-ddr-pmu";
+};
diff --git a/arch/arm/dts/meson-g12b-odroid-go-ultra.dts b/arch/arm/dts/meson-g12b-odroid-go-ultra.dts
new file mode 100644
index 0000000000..1e40709610
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-go-ultra.dts
@@ -0,0 +1,722 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-go-ultra", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-GO-Ultra";
+
+ aliases {
+ serial0 = &uart_AO;
+ rtc0 = &vrtc;
+ };
+
+ adc-joystick-left {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 2>, <&saradc 3>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_Y>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_X>;
+ abs-range = <700 2900>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ adc-joystick-right {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 0>, <&saradc 1>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_RY>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_RX>;
+ abs-range = <800 3000>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ codec_clk: codec-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ clock-output-names = "codec_clk";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <10>;
+ pinctrl-0 = <&keypad_gpio_pins>;
+ pinctrl-names = "default";
+
+ volume-up-button {
+ label = "VOLUME-UP";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpio GPIOX_8 GPIO_ACTIVE_LOW>;
+ };
+ volume-down-button {
+ label = "VOLUME-DOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpio GPIOX_9 GPIO_ACTIVE_LOW>;
+ };
+ dpad-up-button {
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ gpios = <&gpio GPIOX_0 GPIO_ACTIVE_LOW>;
+ };
+ dpad-down-button {
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ gpios = <&gpio GPIOX_1 GPIO_ACTIVE_LOW>;
+ };
+ dpad-left-button {
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ gpios = <&gpio GPIOX_2 GPIO_ACTIVE_LOW>;
+ };
+ dpad-right-button {
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ gpios = <&gpio GPIOX_3 GPIO_ACTIVE_LOW>;
+ };
+ a-button {
+ label = "A";
+ linux,code = <BTN_EAST>;
+ gpios = <&gpio GPIOX_4 GPIO_ACTIVE_LOW>;
+ };
+ b-button {
+ label = "B";
+ linux,code = <BTN_SOUTH>;
+ gpios = <&gpio GPIOX_5 GPIO_ACTIVE_LOW>;
+ };
+ y-button {
+ label = "Y";
+ linux,code = <BTN_WEST>;
+ gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ };
+ x-button {
+ label = "X";
+ linux,code = <BTN_NORTH>;
+ gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ };
+ f1-button {
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&gpio GPIOX_17 GPIO_ACTIVE_LOW>;
+ };
+ f2-button {
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+ };
+ f3-button {
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>;
+ };
+ f4-button {
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ gpios = <&gpio GPIOX_12 GPIO_ACTIVE_LOW>;
+ };
+ f5-button {
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ gpios = <&gpio GPIOX_13 GPIO_ACTIVE_LOW>;
+ };
+ f6-button {
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
+ };
+ top-left-button {
+ label = "TOP Left";
+ linux,code = <BTN_TL>;
+ gpios = <&gpio GPIOX_14 GPIO_ACTIVE_LOW>;
+ };
+ top-left2-button {
+ label = "TOP Left 2";
+ linux,code = <BTN_TL2>;
+ gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+ };
+ top-right-button {
+ label = "TOP Right";
+ linux,code = <BTN_TR>;
+ gpios = <&gpio GPIOX_15 GPIO_ACTIVE_LOW>;
+ };
+ top-right2-button {
+ label = "TOP Right 2";
+ linux,code = <BTN_TR2>;
+ gpios = <&gpio GPIOX_18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vdd_sys: regulator-vdd-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SYS";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "Odroid GO Ultra";
+ audio-widgets = "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_b>, <&speaker_amp>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&rk817>;
+ };
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&hp_5v>;
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+/* RK817 only supports 12.5mV steps, round up the values */
+&cpu_opp_table_0 {
+ opp-1000000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <762500>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <837500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1896000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1992000000 {
+ opp-microvolt = <1012500>;
+ };
+};
+
+/* RK818 only supports 12.5mV steps, round up the values */
+&cpub_opp_table_1 {
+ opp-1000000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <825000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <900000>;
+ };
+ opp-1800000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1908000000 {
+ opp-microvolt = <1025000>;
+ };
+};
+
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>;
+ pinctrl-names = "default";
+
+ rk818: pmic@1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_7 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vcc_2v3>;
+ vcc8-supply = <&vcc_2v3>;
+ vcc9-supply = <&vddao_3v3>;
+ boost-supply = <&vdd_sys>;
+ switch-supply = <&vdd_sys>;
+
+ regulators {
+ vddcpu_a: DCDC_REG1 {
+ regulator-name = "vddcpu_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <775000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <775000>;
+ };
+ };
+
+ vdd_ee: DCDC_REG2 {
+ regulator-name = "vdd_ee";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <875000>;
+ };
+ };
+
+ vddq_1v1: DCDC_REG3 {
+ regulator-name = "vddq_1v1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vddao_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddao_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ hp_5v: DCDC_BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "hp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vddio_ao1v8: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddio_ao1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddq_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddq_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddio_c: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddio_c";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: SWITCH_REG {
+ regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio_intc>;
+
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_5 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc5-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_sys>;
+ vcc8-supply = <&vdd_sys>;
+ vcc9-supply = <&rk817_boost>;
+
+ #sound-dai-cells = <0>;
+ clocks = <&codec_clk>;
+ clock-names = "mclk";
+
+ #clock-cells = <1>;
+
+ regulators {
+ vddcpu_b: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <737500>;
+ regulator-max-microvolt = <1012500>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vddcpu_b";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_2v3: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_2v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "rk817_boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ usb_host: OTG_SWITCH {
+ regulator-name = "usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&periphs_pinctrl {
+ keypad_gpio_pins: keypad-gpio {
+ mux {
+ groups = "GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3",
+ "GPIOX_4", "GPIOX_5", "GPIOX_6", "GPIOX_7",
+ "GPIOX_8", "GPIOX_9", "GPIOX_10", "GPIOX_11",
+ "GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15",
+ "GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_c>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+
+&tdmif_b {
+ pinctrl-0 = <&tdm_b_dout0_pins>, <&tdm_b_fs_pins>, <&tdm_b_sclk_pins>, <&tdm_b_din1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD1>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD1>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb2_phy0 {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ status = "okay";
+ phy-supply = <&usb_host>;
+};
diff --git a/arch/arm/dts/meson-g12b.dtsi b/arch/arm/dts/meson-g12b.dtsi
index ee8fcae9f9..75ff00fb2e 100644
--- a/arch/arm/dts/meson-g12b.dtsi
+++ b/arch/arm/dts/meson-g12b.dtsi
@@ -105,6 +105,7 @@
l2: l2-cache0 {
compatible = "cache";
+ cache-level = <2>;
};
};
};
@@ -139,3 +140,7 @@
&mali {
dma-coherent;
};
+
+&pmu {
+ compatible = "amlogic,g12b-ddr-pmu";
+};
diff --git a/arch/arm/dts/meson-sm1.dtsi b/arch/arm/dts/meson-sm1.dtsi
index 3d8b1f4f20..56ca0ba224 100644
--- a/arch/arm/dts/meson-sm1.dtsi
+++ b/arch/arm/dts/meson-sm1.dtsi
@@ -88,6 +88,7 @@
l2: l2-cache0 {
compatible = "cache";
+ cache-level = <2>;
};
};
@@ -95,26 +96,6 @@
compatible = "operating-points-v2";
opp-shared;
- opp-100000000 {
- opp-hz = /bits/ 64 <100000000>;
- opp-microvolt = <730000>;
- };
-
- opp-250000000 {
- opp-hz = /bits/ 64 <250000000>;
- opp-microvolt = <730000>;
- };
-
- opp-500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <730000>;
- };
-
- opp-667000000 {
- opp-hz = /bits/ 64 <666666666>;
- opp-microvolt = <750000>;
- };
-
opp-1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <770000>;
@@ -356,6 +337,33 @@
status = "disabled";
};
+ spdifin: audio-controller@400 {
+ compatible = "amlogic,g12a-spdifin",
+ "amlogic,axg-spdifin";
+ reg = <0x0 0x400 0x0 0x30>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFIN";
+ interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+ <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+ clock-names = "pclk", "refclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFIN>;
+ status = "disabled";
+ };
+
+ spdifout_a: audio-controller@480 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x480 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT_A";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+ clock-names = "pclk", "mclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFOUT>;
+ status = "disabled";
+ };
+
tdmout_a: audio-controller@500 {
compatible = "amlogic,sm1-tdmout";
reg = <0x0 0x500 0x0 0x40>;
@@ -513,6 +521,10 @@
power-domains = <&pwrc PWRC_SM1_PCIE_ID>;
};
+&pmu {
+ compatible = "amlogic,sm1-ddr-pmu";
+};
+
&pwrc {
compatible = "amlogic,meson-sm1-pwrc";
};
--
2.34.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 2/2] ARM: meson: add support for Odroid Go Ultra
2023-01-19 13:44 [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra Neil Armstrong
2023-01-19 13:44 ` [PATCH 1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1 Neil Armstrong
@ 2023-01-19 13:44 ` Neil Armstrong
2023-01-24 8:25 ` [PATCH 0/2] ARM: arch-meson: " Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-19 13:44 UTC (permalink / raw)
To: u-boot, u-boot-amlogic, Neil Armstrong
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
.../arm/dts/meson-g12b-odroid-go-ultra-u-boot.dtsi | 16 +++++
configs/odroid-go-ultra_defconfig | 70 ++++++++++++++++++++++
doc/board/amlogic/index.rst | 4 +-
doc/board/amlogic/odroid-go-ultra.rst | 34 +++++++++++
4 files changed, 123 insertions(+), 1 deletion(-)
diff --git a/arch/arm/dts/meson-g12b-odroid-go-ultra-u-boot.dtsi b/arch/arm/dts/meson-g12b-odroid-go-ultra-u-boot.dtsi
new file mode 100644
index 0000000000..00852f5e54
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-go-ultra-u-boot.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
+
+/* RK817/818 BOOST regulator aren't supported yet, so remove phandles from PHY nodes */
+
+&usb2_phy1 {
+ /delete-property/ phy-supply;
+};
+
+&usb3_pcie_phy {
+ /delete-property/ phy-supply;
+};
diff --git a/configs/odroid-go-ultra_defconfig b/configs/odroid-go-ultra_defconfig
new file mode 100644
index 0000000000..a4d349fba4
--- /dev/null
+++ b/configs/odroid-go-ultra_defconfig
@@ -0,0 +1,70 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="w400"
+CONFIG_ARCH_MESON=y
+CONFIG_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-odroid-go-ultra"
+CONFIG_MESON_G12A=y
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-go-ultra"
+CONFIG_SYS_LOAD_ADDR=0x1000000
+CONFIG_DEBUG_UART=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000
+CONFIG_REMAKE_ELF=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+CONFIG_SYS_MAXARGS=32
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ADC=y
+CONFIG_SARADC_MESON=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_ADC=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MESON=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_RESET=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_SYSINFO=y
+CONFIG_SYSINFO_SMBIOS=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
index 4d407f9362..11443d9f2c 100644
--- a/doc/board/amlogic/index.rst
+++ b/doc/board/amlogic/index.rst
@@ -19,7 +19,8 @@ This matrix concerns the actual source code version.
| | Nanopi-K2 | Khadas-VIM | Libretech-PC | JetHub J100 | SEI510 | Khadas-VIM3 | Khadas-VIM3L |
| | P200 | LibreTech-CC v1 | WeTek Core2 | | Radxa Zero | GT-King/Pro | Odroid-C4 |
| | P201 | LibreTech-AC v2 | | | | GSKing-X | Odroid-HC4 |
-| | | JetHub J80 | | | | | BananaPi-M5 |
+| | | JetHub J80 | | | | Odroid-Go- | BananaPi-M5 |
+| | | | | | | Ultra | |
+-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
+-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
@@ -105,6 +106,7 @@ Board Documentation
odroid-c2
odroid-c4
odroid-n2
+ odroid-go-ultra
p200
p201
p212
diff --git a/doc/board/amlogic/odroid-go-ultra.rst b/doc/board/amlogic/odroid-go-ultra.rst
new file mode 100644
index 0000000000..8df9e0cb79
--- /dev/null
+++ b/doc/board/amlogic/odroid-go-ultra.rst
@@ -0,0 +1,34 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for ODROID-GO-ULTRA
+==========================
+
+The Odroid Go Ultra is a portable gaming device with the following
+characteristics:
+
+ - Amlogic S922X SoC
+ - RK817 & RK818 PMICs
+ - 2GiB LPDDR4
+ - On board 16GiB eMMC
+ - Micro SD Card slot
+ - 5inch 854×480 MIPI-DSI TFT LCD
+ - Earphone stereo jack, 0.5Watt 8Ω Mono speaker
+ - Li-Polymer 3.7V/4000mAh Battery
+ - USB-A 2.0 Host Connector
+ - x16 GPIO Input Buttons
+ - 2x ADC Analog Joysticks
+ - USB-C Port for USB2 Device and Charging
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+ $ export CROSS_COMPILE=aarch64-none-elf-
+ $ make odroid-go-ultra_defconfig
+ $ make
+
+Image creation
+--------------
+
+Pleaser refer to :doc:`pre-generated-fip` with codename `odroid-go-ultra`
--
2.34.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra
2023-01-19 13:44 [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra Neil Armstrong
2023-01-19 13:44 ` [PATCH 1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1 Neil Armstrong
2023-01-19 13:44 ` [PATCH 2/2] ARM: meson: add support for Odroid Go Ultra Neil Armstrong
@ 2023-01-24 8:25 ` Neil Armstrong
2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-24 8:25 UTC (permalink / raw)
To: u-boot, u-boot-amlogic, Neil Armstrong
Hi,
On Thu, 19 Jan 2023 14:44:17 +0100, Neil Armstrong wrote:
> This adds initial support for the Hardkernel Odroid Go Ultra.
>
> The Odroid Go Ultra is a portable gaming device with the following
> characteristics:
> - Amlogic S922X SoC
> - RK817 & RK818 PMICs
> - 2GiB LPDDR4
> - On board 16GiB eMMC
> - Micro SD Card slot
> - 5inch 854×480 MIPI-DSI TFT LCD
> - Earphone stereo jack, 0.5Watt 8Ω Mono speaker
> - Li-Polymer 3.7V/4000mAh Battery
> - USB-A 2.0 Host Connector
> - x16 GPIO Input Buttons
> - 2x ADC Analog Joysticks
> - USB-C Port for USB2 Device and Charging
>
> [...]
Thanks, Applied to https://source.denx.de/u-boot/custodians/u-boot-amlogic (u-boot-amlogic-test)
[1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1
https://source.denx.de/u-boot/custodians/u-boot-amlogic/-/commit/2acbc33b3d19128cb673a980116e9e33fbc5161f
[2/2] ARM: meson: add support for Odroid Go Ultra
https://source.denx.de/u-boot/custodians/u-boot-amlogic/-/commit/640192d04f9c4003959c967d11b2f98c3756c451
--
Neil
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2023-01-24 8:25 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-19 13:44 [PATCH 0/2] ARM: arch-meson: add support for Odroid Go Ultra Neil Armstrong
2023-01-19 13:44 ` [PATCH 1/2] ARM: dts: sync Amlogic ARM64 DT from v6.2-rc1 Neil Armstrong
2023-01-19 13:44 ` [PATCH 2/2] ARM: meson: add support for Odroid Go Ultra Neil Armstrong
2023-01-24 8:25 ` [PATCH 0/2] ARM: arch-meson: " Neil Armstrong
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.