All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 0/2] ARM: meson: Add support for Odroid-N2L
@ 2023-01-26  9:48 Neil Armstrong
  2023-01-26  9:48 ` [PATCH 1/2] ARM: dts: Import Odroid-N2L support Neil Armstrong
                   ` (2 more replies)
  0 siblings, 3 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-26  9:48 UTC (permalink / raw)
  To: u-boot, u-boot-amlogic, Neil Armstrong

ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.

- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
  are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
  is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added

Is uses Odroid-N2L support posted at [1] and merged for Linux v6.3-rc1.

It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.

[1] https://lore.kernel.org/all/20230122-topic-odroid-n2l-upstream-initial-v2-0-8d3fea6d403d@linaro.org/

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Neil Armstrong (2):
      ARM: dts: Import Odroid-N2L support
      ARM: meson: Add support for Odroid-N2L

 arch/arm/dts/Makefile                          |   1 +
 arch/arm/dts/meson-g12b-odroid-n2.dtsi         | 410 +----------------------
 arch/arm/dts/meson-g12b-odroid-n2l-u-boot.dtsi |   7 +
 arch/arm/dts/meson-g12b-odroid-n2l.dts         | 125 +++++++
 arch/arm/dts/meson-g12b-odroid.dtsi            | 445 +++++++++++++++++++++++++
 configs/odroid-n2l_defconfig                   |  70 ++++
 doc/board/amlogic/index.rst                    |   2 +
 doc/board/amlogic/odroid-n2l.rst               |  31 ++
 8 files changed, 693 insertions(+), 398 deletions(-)
---
base-commit: 640192d04f9c4003959c967d11b2f98c3756c451
change-id: 20230126-u-boot-odroid-n2l-dc8b370b43c6

Best regards,
-- 
Neil Armstrong <neil.armstrong@linaro.org>


^ permalink raw reply	[flat|nested] 4+ messages in thread

* [PATCH 1/2] ARM: dts: Import Odroid-N2L support
  2023-01-26  9:48 [PATCH 0/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
@ 2023-01-26  9:48 ` Neil Armstrong
  2023-01-26  9:48 ` [PATCH 2/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
  2023-01-30 13:24 ` [PATCH 0/2] " Neil Armstrong
  2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-26  9:48 UTC (permalink / raw)
  To: u-boot, u-boot-amlogic, Neil Armstrong

Import Odroid-N2L support posted at [1] and merged for Linux v6.3-rc1.

[1] https://lore.kernel.org/all/20230122-topic-odroid-n2l-upstream-initial-v2-0-8d3fea6d403d@linaro.org/

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm/dts/Makefile                  |   1 +
 arch/arm/dts/meson-g12b-odroid-n2.dtsi | 410 +-----------------------------
 arch/arm/dts/meson-g12b-odroid-n2l.dts | 125 +++++++++
 arch/arm/dts/meson-g12b-odroid.dtsi    | 445 +++++++++++++++++++++++++++++++++
 4 files changed, 583 insertions(+), 398 deletions(-)

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index e8650dc8d5..160451c2a2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -200,6 +200,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12b-gsking-x.dtb \
 	meson-g12b-odroid-go-ultra.dtb \
 	meson-g12b-odroid-n2.dtb \
+	meson-g12b-odroid-n2l.dtb \
 	meson-g12b-odroid-n2-plus.dtb \
 	meson-sm1-bananapi-m5.dtb \
 	meson-sm1-khadas-vim3l.dtb \
diff --git a/arch/arm/dts/meson-g12b-odroid-n2.dtsi b/arch/arm/dts/meson-g12b-odroid-n2.dtsi
index 344573e157..24d0442dff 100644
--- a/arch/arm/dts/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm/dts/meson-g12b-odroid-n2.dtsi
@@ -4,20 +4,14 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
-#include <dt-bindings/sound/meson-g12a-toacodec.h>
-#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+#include "meson-g12b-odroid.dtsi"
 
 / {
 	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
 		rtc0 = &rtc;
-		rtc1 = &vrtc;
 	};
 
-	dioo2133: audio-amplifier-0 {
+	dio2133: audio-amplifier-0 {
 		compatible = "simple-audio-amplifier";
 		enable-gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
 		VCC-supply = <&vcc_5v>;
@@ -25,139 +19,6 @@
 		status = "okay";
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-blue {
-			label = "n2:blue";
-			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	tf_io: gpio-regulator-tf_io {
-		compatible = "regulator-gpio";
-
-		regulator-name = "TF_IO";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
-		gpios-states = <0>;
-
-		states = <3300000 0>,
-			 <1800000 1>;
-	};
-
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	main_12v: regulator-main_12v {
-		compatible = "regulator-fixed";
-		regulator-name = "12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		vin-supply = <&main_12v>;
-	};
-
-	vcc_1v8: regulator-vcc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-		/* FIXME: actually controlled by VDDCPU_B_EN */
-	};
-
-	vddcpu_a: regulator-vddcpu-a {
-		/*
-		 * MP8756GD Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_A";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_ab 0 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vddcpu_b: regulator-vddcpu-b {
-		/*
-		 * Silergy SY8120B1ABC Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_B";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	hub_5v: regulator-hub_5v {
 		compatible = "regulator-fixed";
 		regulator-name = "HUB_5V";
@@ -170,54 +31,13 @@
 		enable-active-high;
 	};
 
-	usb_pwr_en: regulator-usb_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* Connected to the microUSB port power enable */
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&main_12v>;
-		regulator-always-on;
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "ODROID-N2";
 		audio-widgets = "Line", "Lineout";
 		audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>,
 				 <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>,
-				 <&dioo2133>;
+				 <&dio2133>;
 		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
 				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
 				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
@@ -344,68 +164,13 @@
 	status = "okay";
 };
 
-&arb {
-	status = "okay";
-};
-
-&cec_AO {
-	pinctrl-0 = <&cec_ao_a_h_pins>;
-	pinctrl-names = "default";
-	status = "disabled";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
-	pinctrl-0 = <&cec_ao_b_h_pins>;
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
 	pinctrl-names = "default";
 	status = "okay";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&clkc_audio {
-	status = "okay";
-};
-
-&cpu0 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu100 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu101 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu102 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu103 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
 };
 
 &ext_mdio {
@@ -424,27 +189,6 @@
 	};
 };
 
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&external_phy>;
-	amlogic,tx-delay-ns = <2>;
-};
-
-&frddr_a {
-	status = "okay";
-};
-
-&frddr_b {
-	status = "okay";
-};
-
-&frddr_c {
-	status = "okay";
-};
-
 &gpio {
 	gpio-line-names =
 		/* GPIOZ */
@@ -505,26 +249,6 @@
 	};
 };
 
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-	linux,rc-map-name = "rc-odroid";
-};
-
 &i2c3 {
 	status = "okay";
 	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
@@ -537,62 +261,11 @@
 	};
 };
 
-&pwm_ab {
-	pinctrl-0 = <&pwm_a_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
+&ir {
 	status = "okay";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-0 = <&remote_input_ao_pins>;
 	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-	vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&tf_io>;
-
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&flash_1v8>;
+	linux,rc-map-name = "rc-odroid";
 };
 
 /*
@@ -607,7 +280,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	mx25u64: spi-flash@0 {
+	mx25u64: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mxicy,mx25u6435f", "jedec,spi-nor";
@@ -616,73 +289,14 @@
 	};
 };
 
-&tdmif_b {
-	status = "okay";
-};
-
-&tdmif_c {
-	status = "okay";
-};
-
-&tdmin_a {
-	status = "okay";
-};
-
-&tdmin_b {
-	status = "okay";
-};
-
-&tdmin_c {
-	status = "okay";
-};
-
-&tdmin_lb {
-	status = "okay";
-};
-
-&tdmout_b {
-	status = "okay";
-};
-
-&tdmout_c {
-	status = "okay";
-};
-
 &toacodec {
 	status = "okay";
 };
 
-&tohdmitx {
-	status = "okay";
-};
-
-&toddr_a {
-	status = "okay";
-};
-
-&toddr_b {
-	status = "okay";
-};
-
-&toddr_c {
-	status = "okay";
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
 &usb {
-	status = "okay";
 	vbus-supply = <&usb_pwr_en>;
 };
 
-&usb2_phy0 {
-	phy-supply = <&vcc_5v>;
-};
-
 &usb2_phy1 {
 	/* Enable the hub which is connected to this port */
 	phy-supply = <&hub_5v>;
diff --git a/arch/arm/dts/meson-g12b-odroid-n2l.dts b/arch/arm/dts/meson-g12b-odroid-n2l.dts
new file mode 100644
index 0000000000..70919f40d5
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-n2l.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Dongjin Kim <tobetter@gmail.com>
+ */
+
+/dts-v1/;
+
+/* The Amlogic S922X Rev. C supports the same OPPs as the A311D variant */
+#include "meson-g12b-a311d.dtsi"
+#include "meson-g12b-odroid.dtsi"
+
+/ {
+	compatible = "hardkernel,odroid-n2l", "amlogic,s922x", "amlogic,g12b";
+	model = "Hardkernel ODROID-N2L";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "ODROID-N2L";
+		audio-aux-devs = <&tdmout_b>, <&tdmin_a>, <&tdmin_b>,
+				 <&tdmin_c>, <&tdmin_lb>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT",
+				"TDMIN_A IN 4", "TDM_B Loopback",
+				"TDMIN_B IN 4", "TDM_B Loopback",
+				"TDMIN_C IN 4", "TDM_B Loopback",
+				"TDMIN_LB IN 1", "TDM_B Loopback",
+				"TODDR_A IN 0", "TDMIN_A OUT",
+				"TODDR_B IN 0", "TDMIN_A OUT",
+				"TODDR_C IN 0", "TDMIN_A OUT",
+				"TODDR_A IN 1", "TDMIN_B OUT",
+				"TODDR_B IN 1", "TDMIN_B OUT",
+				"TODDR_C IN 1", "TDMIN_B OUT",
+				"TODDR_A IN 2", "TDMIN_C OUT",
+				"TODDR_B IN 2", "TDMIN_C OUT",
+				"TODDR_C IN 2", "TDMIN_C OUT",
+				"TODDR_A IN 6", "TDMIN_LB OUT",
+				"TODDR_B IN 6", "TDMIN_LB OUT",
+				"TODDR_C IN 6", "TDMIN_LB OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		dai-link-3 {
+			sound-dai = <&toddr_a>;
+		};
+
+		dai-link-4 {
+			sound-dai = <&toddr_b>;
+		};
+
+		dai-link-5 {
+			sound-dai = <&toddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-6 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-7 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&eth_phy {
+	status = "disabled";
+};
+
+&vddcpu_a {
+	regulator-min-microvolt = <680000>;
+	regulator-max-microvolt = <1040000>;
+
+	pwms = <&pwm_ab 0 1500 0>;
+};
+
+&vddcpu_b {
+	regulator-min-microvolt = <680000>;
+	regulator-max-microvolt = <1040000>;
+
+	pwms = <&pwm_AO_cd 1 1500 0>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+	phy-supply = <&usb_pwr_en>;
+};
diff --git a/arch/arm/dts/meson-g12b-odroid.dtsi b/arch/arm/dts/meson-g12b-odroid.dtsi
new file mode 100644
index 0000000000..9e12a34b28
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid.dtsi
@@ -0,0 +1,445 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		rtc1 = &vrtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
+		/* Using Dummy Speed */
+		gpio-fan,speed-map = <0 0>, <1 1>;
+		#cooling-cells = <2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			label = "n2:blue";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+			 <1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&main_12v>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vddcpu_a: regulator-vddcpu-a {
+		/*
+		 * MP8756GD Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_A";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		pwm-supply = <&main_12v>;
+
+		pwms = <&pwm_ab 0 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddcpu_b: regulator-vddcpu-b {
+		/*
+		 * Silergy SY8120B1ABC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_B";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		pwm-supply = <&main_12v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu100 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu101 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu102 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu103 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu_thermal {
+	trips {
+		cpu_active: cpu-active {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpu_active>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&ddr_thermal {
+	trips {
+		ddr_active: ddr-active {
+			temperature = <60000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&ddr_active>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&pwm_ab {
+	pinctrl-0 = <&pwm_a_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+	status = "okay";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmif_c {
+	status = "okay";
+};
+
+&tdmin_a {
+	status = "okay";
+};
+
+&tdmin_b {
+	status = "okay";
+};
+
+&tdmin_c {
+	status = "okay";
+};
+
+&tdmin_lb {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tdmout_c {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&toddr_a {
+	status = "okay";
+};
+
+&toddr_b {
+	status = "okay";
+};
+
+&toddr_c {
+	status = "okay";
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};

-- 
2.34.1


^ permalink raw reply related	[flat|nested] 4+ messages in thread

* [PATCH 2/2] ARM: meson: Add support for Odroid-N2L
  2023-01-26  9:48 [PATCH 0/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
  2023-01-26  9:48 ` [PATCH 1/2] ARM: dts: Import Odroid-N2L support Neil Armstrong
@ 2023-01-26  9:48 ` Neil Armstrong
  2023-01-30 13:24 ` [PATCH 0/2] " Neil Armstrong
  2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-26  9:48 UTC (permalink / raw)
  To: u-boot, u-boot-amlogic, Neil Armstrong

ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.

- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
  are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
  is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added

It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm/dts/meson-g12b-odroid-n2l-u-boot.dtsi |  7 +++
 configs/odroid-n2l_defconfig                   | 70 ++++++++++++++++++++++++++
 doc/board/amlogic/index.rst                    |  2 +
 doc/board/amlogic/odroid-n2l.rst               | 31 ++++++++++++
 4 files changed, 110 insertions(+)

diff --git a/arch/arm/dts/meson-g12b-odroid-n2l-u-boot.dtsi b/arch/arm/dts/meson-g12b-odroid-n2l-u-boot.dtsi
new file mode 100644
index 0000000000..236f2468dc
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-n2l-u-boot.dtsi
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
diff --git a/configs/odroid-n2l_defconfig b/configs/odroid-n2l_defconfig
new file mode 100644
index 0000000000..7f9e64d942
--- /dev/null
+++ b/configs/odroid-n2l_defconfig
@@ -0,0 +1,70 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="w400"
+CONFIG_ARCH_MESON=y
+CONFIG_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-odroid-n2l"
+CONFIG_MESON_G12A=y
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-n2l"
+CONFIG_SYS_LOAD_ADDR=0x1000000
+CONFIG_DEBUG_UART=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20000000
+CONFIG_REMAKE_ELF=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+CONFIG_SYS_MAXARGS=32
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ADC=y
+CONFIG_SARADC_MESON=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_VIDEO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP16 is not set
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_BMP_16BPP=y
+CONFIG_BMP_24BPP=y
+CONFIG_BMP_32BPP=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
index 11443d9f2c..f945f672dd 100644
--- a/doc/board/amlogic/index.rst
+++ b/doc/board/amlogic/index.rst
@@ -21,6 +21,7 @@ This matrix concerns the actual source code version.
 |                               | P201      | LibreTech-AC v2 |              |             |            | GSKing-X    | Odroid-HC4   |
 |                               |           | JetHub J80      |              |             |            | Odroid-Go-  | BananaPi-M5  |
 |                               |           |                 |              |             |            | Ultra       |              |
+|                               |           |                 |              |             |            | Odroid-N2L  |              |
 +-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
 | UART                          | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
 +-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
@@ -106,6 +107,7 @@ Board Documentation
    odroid-c2
    odroid-c4
    odroid-n2
+   odroid-n2l
    odroid-go-ultra
    p200
    p201
diff --git a/doc/board/amlogic/odroid-n2l.rst b/doc/board/amlogic/odroid-n2l.rst
new file mode 100644
index 0000000000..afd4409d1b
--- /dev/null
+++ b/doc/board/amlogic/odroid-n2l.rst
@@ -0,0 +1,31 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for ODROID-N2L
+=====================
+
+ODROID-N2L is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
+ - 4GB DDR4 SDRAM
+ - HDMI 2.1 4K/60Hz display
+ - 40-pin GPIO header
+ - 1 x USB 3.0 Host, 1 x USB USB 2.0 Host
+ - eMMC, microSD
+ - MIPI DSI Port
+
+Schematics are available on the manufacturer website.
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+    $ export CROSS_COMPILE=aarch64-none-elf-
+    $ make odroid-n2l_defconfig
+    $ make
+
+Image creation
+--------------
+
+For simplified usage, pleaser refer to :doc:`pre-generated-fip` with codename `odroid-n2l`

-- 
2.34.1


^ permalink raw reply related	[flat|nested] 4+ messages in thread

* Re: [PATCH 0/2] ARM: meson: Add support for Odroid-N2L
  2023-01-26  9:48 [PATCH 0/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
  2023-01-26  9:48 ` [PATCH 1/2] ARM: dts: Import Odroid-N2L support Neil Armstrong
  2023-01-26  9:48 ` [PATCH 2/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
@ 2023-01-30 13:24 ` Neil Armstrong
  2 siblings, 0 replies; 4+ messages in thread
From: Neil Armstrong @ 2023-01-30 13:24 UTC (permalink / raw)
  To: u-boot, u-boot-amlogic, Neil Armstrong

Hi,

On Thu, 26 Jan 2023 10:48:19 +0100, Neil Armstrong wrote:
> ODROID-N2L is a variant SBC in small form factor and some peripherals
> are removed from ODROID-N2PLUS based on S922X SoC.
> 
> - On-board ethernet is removed
> - On-board RTC is removed
> - USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
>   are available
> - Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
>   is recommended or a tall passive sink is optional
> - 3.5mm earjack is removed
> - IR remote receiver is removed
> - MIPI DSI port is added
> 
> [...]

Thanks, Applied to https://source.denx.de/u-boot/custodians/u-boot-amlogic (u-boot-amlogic-test)

[1/2] ARM: dts: Import Odroid-N2L support
      https://source.denx.de/u-boot/custodians/u-boot-amlogic/-/commit/5017e305ee1c12b757b68f1ed3cfa05d191da3e8
[2/2] ARM: meson: Add support for Odroid-N2L
      https://source.denx.de/u-boot/custodians/u-boot-amlogic/-/commit/8f5e9de121003bfd9a64a5b3a503c0fbd02af823

-- 
Neil


^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2023-01-30 13:24 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-26  9:48 [PATCH 0/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
2023-01-26  9:48 ` [PATCH 1/2] ARM: dts: Import Odroid-N2L support Neil Armstrong
2023-01-26  9:48 ` [PATCH 2/2] ARM: meson: Add support for Odroid-N2L Neil Armstrong
2023-01-30 13:24 ` [PATCH 0/2] " Neil Armstrong

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.