* [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-06 13:16 ` Icenowy Zheng
0 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-06 13:16 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Icenowy Zheng
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v4:
- Use SPDX license identifier.
Changes in v3:
- Add comments about Vbus problem in &usbphy node.
Changes in v2:
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
--
2.15.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-06 13:16 ` Icenowy Zheng
0 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-06 13:16 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
---
Changes in v4:
- Use SPDX license identifier.
Changes in v3:
- Add comments about Vbus problem in &usbphy node.
Changes in v2:
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
--
2.15.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-06 13:16 ` Icenowy Zheng
0 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-06 13:16 UTC (permalink / raw)
To: linux-arm-kernel
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v4:
- Use SPDX license identifier.
Changes in v3:
- Add comments about Vbus problem in &usbphy node.
Changes in v2:
- Use high active SD card detect on the production batch.
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
2 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..d5a17e6e8b0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..e2ee65a5bf92
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
--
2.15.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
2018-02-06 13:16 ` Icenowy Zheng
@ 2018-02-08 9:00 ` Maxime Ripard
-1 siblings, 0 replies; 14+ messages in thread
From: Maxime Ripard @ 2018-02-08 9:00 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 2494 bytes --]
On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> factor and GPIO holes similar to Raspberry Pi Zero.
>
> It features:
> - Allwinner H2+ SoC
> - Single-chip (16-bit) 512MiB DDR3 DRAM
> - Ampak AP6212 Wi-Fi/Bluetooth module
> - MicroSD slot
> - Two MicroUSB Type-B ports (one can only be used to power the board and
> the other features OTG functionality)
> - Two keys, a reset and a GPIO-connected key.
> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> - CSI connector to connect the camera sensor provided by Sinovoip.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v4:
> - Use SPDX license identifier.
>
> Changes in v3:
> - Add comments about Vbus problem in &usbphy node.
>
> Changes in v2:
> - Use high active SD card detect on the production batch.
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
> 2 files changed, 127 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38543dc..d5a17e6e8b0f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-a83t-cubietruck-plus.dtb \
> sun8i-a83t-tbs-a711.dtb \
> sun8i-h2-plus-orangepi-r1.dtb \
> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> sun8i-h2-plus-orangepi-zero.dtb \
> sun8i-h3-bananapi-m2-plus.dtb \
> sun8i-h3-beelink-x2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> new file mode 100644
> index 000000000000..e2ee65a5bf92
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -0,0 +1,126 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Sorry to be a bit picky about this, but this should be your very first
line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for example.
Thanks!
Maxime
--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:00 ` Maxime Ripard
0 siblings, 0 replies; 14+ messages in thread
From: Maxime Ripard @ 2018-02-08 9:00 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> factor and GPIO holes similar to Raspberry Pi Zero.
>
> It features:
> - Allwinner H2+ SoC
> - Single-chip (16-bit) 512MiB DDR3 DRAM
> - Ampak AP6212 Wi-Fi/Bluetooth module
> - MicroSD slot
> - Two MicroUSB Type-B ports (one can only be used to power the board and
> the other features OTG functionality)
> - Two keys, a reset and a GPIO-connected key.
> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> - CSI connector to connect the camera sensor provided by Sinovoip.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v4:
> - Use SPDX license identifier.
>
> Changes in v3:
> - Add comments about Vbus problem in &usbphy node.
>
> Changes in v2:
> - Use high active SD card detect on the production batch.
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126 +++++++++++++++++++++
> 2 files changed, 127 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38543dc..d5a17e6e8b0f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-a83t-cubietruck-plus.dtb \
> sun8i-a83t-tbs-a711.dtb \
> sun8i-h2-plus-orangepi-r1.dtb \
> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> sun8i-h2-plus-orangepi-zero.dtb \
> sun8i-h3-bananapi-m2-plus.dtb \
> sun8i-h3-beelink-x2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> new file mode 100644
> index 000000000000..e2ee65a5bf92
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -0,0 +1,126 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
> + *
> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Sorry to be a bit picky about this, but this should be your very first
line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for example.
Thanks!
Maxime
--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180208/08e284ad/attachment.sig>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
2018-02-08 9:00 ` Maxime Ripard
(?)
@ 2018-02-08 9:15 ` Icenowy Zheng
-1 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-08 9:15 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel, linux-sunxi
在 2018-02-08 17:00,Maxime Ripard 写道:
> On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> factor and GPIO holes similar to Raspberry Pi Zero.
>>
>> It features:
>> - Allwinner H2+ SoC
>> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> - Ampak AP6212 Wi-Fi/Bluetooth module
>> - MicroSD slot
>> - Two MicroUSB Type-B ports (one can only be used to power the board
>> and
>> the other features OTG functionality)
>> - Two keys, a reset and a GPIO-connected key.
>> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> - CSI connector to connect the camera sensor provided by Sinovoip.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> Changes in v4:
>> - Use SPDX license identifier.
>>
>> Changes in v3:
>> - Add comments about Vbus problem in &usbphy node.
>>
>> Changes in v2:
>> - Use high active SD card detect on the production batch.
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> +++++++++++++++++++++
>> 2 files changed, 127 insertions(+)
>> create mode 100644
>> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..d5a17e6e8b0f 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-a83t-cubietruck-plus.dtb \
>> sun8i-a83t-tbs-a711.dtb \
>> sun8i-h2-plus-orangepi-r1.dtb \
>> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> sun8i-h2-plus-orangepi-zero.dtb \
>> sun8i-h3-bananapi-m2-plus.dtb \
>> sun8i-h3-beelink-x2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> new file mode 100644
>> index 000000000000..e2ee65a5bf92
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> @@ -0,0 +1,126 @@
>> +/*
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>
> Sorry to be a bit picky about this, but this should be your very first
> line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Thanks!
> Maxime
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:15 ` Icenowy Zheng
0 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-08 9:15 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
在 2018-02-08 17:00,Maxime Ripard 写道:
> On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> factor and GPIO holes similar to Raspberry Pi Zero.
>>
>> It features:
>> - Allwinner H2+ SoC
>> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> - Ampak AP6212 Wi-Fi/Bluetooth module
>> - MicroSD slot
>> - Two MicroUSB Type-B ports (one can only be used to power the board
>> and
>> the other features OTG functionality)
>> - Two keys, a reset and a GPIO-connected key.
>> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> - CSI connector to connect the camera sensor provided by Sinovoip.
>>
>> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> ---
>> Changes in v4:
>> - Use SPDX license identifier.
>>
>> Changes in v3:
>> - Add comments about Vbus problem in &usbphy node.
>>
>> Changes in v2:
>> - Use high active SD card detect on the production batch.
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> +++++++++++++++++++++
>> 2 files changed, 127 insertions(+)
>> create mode 100644
>> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..d5a17e6e8b0f 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-a83t-cubietruck-plus.dtb \
>> sun8i-a83t-tbs-a711.dtb \
>> sun8i-h2-plus-orangepi-r1.dtb \
>> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> sun8i-h2-plus-orangepi-zero.dtb \
>> sun8i-h3-bananapi-m2-plus.dtb \
>> sun8i-h3-beelink-x2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> new file mode 100644
>> index 000000000000..e2ee65a5bf92
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> @@ -0,0 +1,126 @@
>> +/*
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> + *
>> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> + * Copyright (C) 2016 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>
> Sorry to be a bit picky about this, but this should be your very first
> line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Thanks!
> Maxime
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:15 ` Icenowy Zheng
0 siblings, 0 replies; 14+ messages in thread
From: Icenowy Zheng @ 2018-02-08 9:15 UTC (permalink / raw)
To: linux-arm-kernel
? 2018-02-08 17:00?Maxime Ripard ???
> On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> factor and GPIO holes similar to Raspberry Pi Zero.
>>
>> It features:
>> - Allwinner H2+ SoC
>> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> - Ampak AP6212 Wi-Fi/Bluetooth module
>> - MicroSD slot
>> - Two MicroUSB Type-B ports (one can only be used to power the board
>> and
>> the other features OTG functionality)
>> - Two keys, a reset and a GPIO-connected key.
>> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> - CSI connector to connect the camera sensor provided by Sinovoip.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> Changes in v4:
>> - Use SPDX license identifier.
>>
>> Changes in v3:
>> - Add comments about Vbus problem in &usbphy node.
>>
>> Changes in v2:
>> - Use high active SD card detect on the production batch.
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> +++++++++++++++++++++
>> 2 files changed, 127 insertions(+)
>> create mode 100644
>> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..d5a17e6e8b0f 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-a83t-cubietruck-plus.dtb \
>> sun8i-a83t-tbs-a711.dtb \
>> sun8i-h2-plus-orangepi-r1.dtb \
>> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> sun8i-h2-plus-orangepi-zero.dtb \
>> sun8i-h3-bananapi-m2-plus.dtb \
>> sun8i-h3-beelink-x2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> new file mode 100644
>> index 000000000000..e2ee65a5bf92
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> @@ -0,0 +1,126 @@
>> +/*
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>
> Sorry to be a bit picky about this, but this should be your very first
> line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Thanks!
> Maxime
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:28 ` Jernej Škrabec
0 siblings, 0 replies; 14+ messages in thread
From: Jernej Škrabec @ 2018-02-08 9:28 UTC (permalink / raw)
To: linux-sunxi, icenowy
Cc: Maxime Ripard, Chen-Yu Tsai, devicetree, linux-arm-kernel, linux-kernel
Dne četrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
> 在 2018-02-08 17:00,Maxime Ripard 写道:
>
> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> >> factor and GPIO holes similar to Raspberry Pi Zero.
> >>
> >> It features:
> >> - Allwinner H2+ SoC
> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
> >> - Ampak AP6212 Wi-Fi/Bluetooth module
> >> - MicroSD slot
> >> - Two MicroUSB Type-B ports (one can only be used to power the board
> >> and
> >>
> >> the other features OTG functionality)
> >>
> >> - Two keys, a reset and a GPIO-connected key.
> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> >> - CSI connector to connect the camera sensor provided by Sinovoip.
> >>
> >> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> >> ---
> >> Changes in v4:
> >> - Use SPDX license identifier.
> >>
> >> Changes in v3:
> >> - Add comments about Vbus problem in &usbphy node.
> >>
> >> Changes in v2:
> >> - Use high active SD card detect on the production batch.
> >>
> >> arch/arm/boot/dts/Makefile | 1 +
> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
> >>
> >> +++++++++++++++++++++
> >>
> >> 2 files changed, 127 insertions(+)
> >> create mode 100644
> >>
> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >>
> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >> index ade7a38543dc..d5a17e6e8b0f 100644
> >> --- a/arch/arm/boot/dts/Makefile
> >> +++ b/arch/arm/boot/dts/Makefile
> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> >>
> >> sun8i-a83t-cubietruck-plus.dtb \
> >> sun8i-a83t-tbs-a711.dtb \
> >> sun8i-h2-plus-orangepi-r1.dtb \
> >>
> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> >>
> >> sun8i-h2-plus-orangepi-zero.dtb \
> >> sun8i-h3-bananapi-m2-plus.dtb \
> >> sun8i-h3-beelink-x2.dtb \
> >>
> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> new file mode 100644
> >> index 000000000000..e2ee65a5bf92
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> @@ -0,0 +1,126 @@
> >> +/*
> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> >> + *
> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
> >> + *
> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >
> > Sorry to be a bit picky about this, but this should be your very first
> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> > example.
>
> I think it's also OK here, see
> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Lincesing rules [1] says it should be in first possible line which can contain
comment.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
Documentation/process/license-rules.rst#n57
>
> > Thanks!
> > Maxime
>
> --
> You received this message because you are subscribed to the Google Groups
> "linux-sunxi" group. To unsubscribe from this group and stop receiving
> emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:28 ` Jernej Škrabec
0 siblings, 0 replies; 14+ messages in thread
From: Jernej Škrabec @ 2018-02-08 9:28 UTC (permalink / raw)
To: linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, icenowy-h8G6r0blFSE
Cc: Maxime Ripard, Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Dne četrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
> 在 2018-02-08 17:00,Maxime Ripard 写道:
>
> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> >> factor and GPIO holes similar to Raspberry Pi Zero.
> >>
> >> It features:
> >> - Allwinner H2+ SoC
> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
> >> - Ampak AP6212 Wi-Fi/Bluetooth module
> >> - MicroSD slot
> >> - Two MicroUSB Type-B ports (one can only be used to power the board
> >> and
> >>
> >> the other features OTG functionality)
> >>
> >> - Two keys, a reset and a GPIO-connected key.
> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> >> - CSI connector to connect the camera sensor provided by Sinovoip.
> >>
> >> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> >> ---
> >> Changes in v4:
> >> - Use SPDX license identifier.
> >>
> >> Changes in v3:
> >> - Add comments about Vbus problem in &usbphy node.
> >>
> >> Changes in v2:
> >> - Use high active SD card detect on the production batch.
> >>
> >> arch/arm/boot/dts/Makefile | 1 +
> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
> >>
> >> +++++++++++++++++++++
> >>
> >> 2 files changed, 127 insertions(+)
> >> create mode 100644
> >>
> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >>
> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >> index ade7a38543dc..d5a17e6e8b0f 100644
> >> --- a/arch/arm/boot/dts/Makefile
> >> +++ b/arch/arm/boot/dts/Makefile
> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> >>
> >> sun8i-a83t-cubietruck-plus.dtb \
> >> sun8i-a83t-tbs-a711.dtb \
> >> sun8i-h2-plus-orangepi-r1.dtb \
> >>
> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> >>
> >> sun8i-h2-plus-orangepi-zero.dtb \
> >> sun8i-h3-bananapi-m2-plus.dtb \
> >> sun8i-h3-beelink-x2.dtb \
> >>
> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> new file mode 100644
> >> index 000000000000..e2ee65a5bf92
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> @@ -0,0 +1,126 @@
> >> +/*
> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> >> + *
> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> >> + *
> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >
> > Sorry to be a bit picky about this, but this should be your very first
> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> > example.
>
> I think it's also OK here, see
> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Lincesing rules [1] says it should be in first possible line which can contain
comment.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
Documentation/process/license-rules.rst#n57
>
> > Thanks!
> > Maxime
>
> --
> You received this message because you are subscribed to the Google Groups
> "linux-sunxi" group. To unsubscribe from this group and stop receiving
> emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org.
> For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 14+ messages in thread
* [linux-sunxi] Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:28 ` Jernej Škrabec
0 siblings, 0 replies; 14+ messages in thread
From: Jernej Škrabec @ 2018-02-08 9:28 UTC (permalink / raw)
To: linux-arm-kernel
Dne ?etrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
> ? 2018-02-08 17:00?Maxime Ripard ???
>
> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> >> factor and GPIO holes similar to Raspberry Pi Zero.
> >>
> >> It features:
> >> - Allwinner H2+ SoC
> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
> >> - Ampak AP6212 Wi-Fi/Bluetooth module
> >> - MicroSD slot
> >> - Two MicroUSB Type-B ports (one can only be used to power the board
> >> and
> >>
> >> the other features OTG functionality)
> >>
> >> - Two keys, a reset and a GPIO-connected key.
> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> >> - CSI connector to connect the camera sensor provided by Sinovoip.
> >>
> >> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> >> ---
> >> Changes in v4:
> >> - Use SPDX license identifier.
> >>
> >> Changes in v3:
> >> - Add comments about Vbus problem in &usbphy node.
> >>
> >> Changes in v2:
> >> - Use high active SD card detect on the production batch.
> >>
> >> arch/arm/boot/dts/Makefile | 1 +
> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
> >>
> >> +++++++++++++++++++++
> >>
> >> 2 files changed, 127 insertions(+)
> >> create mode 100644
> >>
> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >>
> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> >> index ade7a38543dc..d5a17e6e8b0f 100644
> >> --- a/arch/arm/boot/dts/Makefile
> >> +++ b/arch/arm/boot/dts/Makefile
> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> >>
> >> sun8i-a83t-cubietruck-plus.dtb \
> >> sun8i-a83t-tbs-a711.dtb \
> >> sun8i-h2-plus-orangepi-r1.dtb \
> >>
> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> >>
> >> sun8i-h2-plus-orangepi-zero.dtb \
> >> sun8i-h3-bananapi-m2-plus.dtb \
> >> sun8i-h3-beelink-x2.dtb \
> >>
> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> new file mode 100644
> >> index 000000000000..e2ee65a5bf92
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >> @@ -0,0 +1,126 @@
> >> +/*
> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> >> + *
> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
> >> + *
> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >
> > Sorry to be a bit picky about this, but this should be your very first
> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> > example.
>
> I think it's also OK here, see
> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
Lincesing rules [1] says it should be in first possible line which can contain
comment.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
Documentation/process/license-rules.rst#n57
>
> > Thanks!
> > Maxime
>
> --
> You received this message because you are subscribed to the Google Groups
> "linux-sunxi" group. To unsubscribe from this group and stop receiving
> emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
2018-02-08 9:28 ` Jernej Škrabec
(?)
@ 2018-02-08 9:41 ` Chen-Yu Tsai
-1 siblings, 0 replies; 14+ messages in thread
From: Chen-Yu Tsai @ 2018-02-08 9:41 UTC (permalink / raw)
To: Jernej Škrabec
Cc: linux-sunxi, Icenowy Zheng, Maxime Ripard, devicetree,
linux-arm-kernel, linux-kernel
On Thu, Feb 8, 2018 at 5:28 PM, Jernej Škrabec <jernej.skrabec@siol.net> wrote:
> Dne četrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
>> 在 2018-02-08 17:00,Maxime Ripard 写道:
>>
>> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> >> factor and GPIO holes similar to Raspberry Pi Zero.
>> >>
>> >> It features:
>> >> - Allwinner H2+ SoC
>> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> >> - Ampak AP6212 Wi-Fi/Bluetooth module
>> >> - MicroSD slot
>> >> - Two MicroUSB Type-B ports (one can only be used to power the board
>> >> and
>> >>
>> >> the other features OTG functionality)
>> >>
>> >> - Two keys, a reset and a GPIO-connected key.
>> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> >> - CSI connector to connect the camera sensor provided by Sinovoip.
>> >>
>> >> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> >> ---
>> >> Changes in v4:
>> >> - Use SPDX license identifier.
>> >>
>> >> Changes in v3:
>> >> - Add comments about Vbus problem in &usbphy node.
>> >>
>> >> Changes in v2:
>> >> - Use high active SD card detect on the production batch.
>> >>
>> >> arch/arm/boot/dts/Makefile | 1 +
>> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> >>
>> >> +++++++++++++++++++++
>> >>
>> >> 2 files changed, 127 insertions(+)
>> >> create mode 100644
>> >>
>> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >>
>> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> >> index ade7a38543dc..d5a17e6e8b0f 100644
>> >> --- a/arch/arm/boot/dts/Makefile
>> >> +++ b/arch/arm/boot/dts/Makefile
>> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> >>
>> >> sun8i-a83t-cubietruck-plus.dtb \
>> >> sun8i-a83t-tbs-a711.dtb \
>> >> sun8i-h2-plus-orangepi-r1.dtb \
>> >>
>> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> >>
>> >> sun8i-h2-plus-orangepi-zero.dtb \
>> >> sun8i-h3-bananapi-m2-plus.dtb \
>> >> sun8i-h3-beelink-x2.dtb \
>> >>
>> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> new file mode 100644
>> >> index 000000000000..e2ee65a5bf92
>> >> --- /dev/null
>> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> @@ -0,0 +1,126 @@
>> >> +/*
>> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> >> + *
>> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
>> >> + *
>> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> >
>> > Sorry to be a bit picky about this, but this should be your very first
>> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
>> > example.
>>
>> I think it's also OK here, see
>> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Lincesing rules [1] says it should be in first possible line which can contain
> comment.
>
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
> Documentation/process/license-rules.rst#n57
I confess I only read the license line rule some time after I posted that
patch.
ChenYu
>>
>> > Thanks!
>> > Maxime
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "linux-sunxi" group. To unsubscribe from this group and stop receiving
>> emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.
>
>
>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [linux-sunxi] Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:41 ` Chen-Yu Tsai
0 siblings, 0 replies; 14+ messages in thread
From: Chen-Yu Tsai @ 2018-02-08 9:41 UTC (permalink / raw)
To: Jernej Škrabec
Cc: linux-sunxi, Icenowy Zheng, Maxime Ripard, devicetree,
linux-arm-kernel, linux-kernel
On Thu, Feb 8, 2018 at 5:28 PM, Jernej Škrabec <jernej.skrabec-gGgVlfcn5nU@public.gmane.org> wrote:
> Dne četrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
>> 在 2018-02-08 17:00,Maxime Ripard 写道:
>>
>> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> >> factor and GPIO holes similar to Raspberry Pi Zero.
>> >>
>> >> It features:
>> >> - Allwinner H2+ SoC
>> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> >> - Ampak AP6212 Wi-Fi/Bluetooth module
>> >> - MicroSD slot
>> >> - Two MicroUSB Type-B ports (one can only be used to power the board
>> >> and
>> >>
>> >> the other features OTG functionality)
>> >>
>> >> - Two keys, a reset and a GPIO-connected key.
>> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> >> - CSI connector to connect the camera sensor provided by Sinovoip.
>> >>
>> >> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> >> ---
>> >> Changes in v4:
>> >> - Use SPDX license identifier.
>> >>
>> >> Changes in v3:
>> >> - Add comments about Vbus problem in &usbphy node.
>> >>
>> >> Changes in v2:
>> >> - Use high active SD card detect on the production batch.
>> >>
>> >> arch/arm/boot/dts/Makefile | 1 +
>> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> >>
>> >> +++++++++++++++++++++
>> >>
>> >> 2 files changed, 127 insertions(+)
>> >> create mode 100644
>> >>
>> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >>
>> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> >> index ade7a38543dc..d5a17e6e8b0f 100644
>> >> --- a/arch/arm/boot/dts/Makefile
>> >> +++ b/arch/arm/boot/dts/Makefile
>> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> >>
>> >> sun8i-a83t-cubietruck-plus.dtb \
>> >> sun8i-a83t-tbs-a711.dtb \
>> >> sun8i-h2-plus-orangepi-r1.dtb \
>> >>
>> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> >>
>> >> sun8i-h2-plus-orangepi-zero.dtb \
>> >> sun8i-h3-bananapi-m2-plus.dtb \
>> >> sun8i-h3-beelink-x2.dtb \
>> >>
>> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> new file mode 100644
>> >> index 000000000000..e2ee65a5bf92
>> >> --- /dev/null
>> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> @@ -0,0 +1,126 @@
>> >> +/*
>> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> >> + *
>> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> >> + *
>> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> >
>> > Sorry to be a bit picky about this, but this should be your very first
>> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
>> > example.
>>
>> I think it's also OK here, see
>> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Lincesing rules [1] says it should be in first possible line which can contain
> comment.
>
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
> Documentation/process/license-rules.rst#n57
I confess I only read the license line rule some time after I posted that
patch.
ChenYu
>>
>> > Thanks!
>> > Maxime
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "linux-sunxi" group. To unsubscribe from this group and stop receiving
>> emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
>> For more options, visit https://groups.google.com/d/optout.
>
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [linux-sunxi] Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
@ 2018-02-08 9:41 ` Chen-Yu Tsai
0 siblings, 0 replies; 14+ messages in thread
From: Chen-Yu Tsai @ 2018-02-08 9:41 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Feb 8, 2018 at 5:28 PM, Jernej ?krabec <jernej.skrabec@siol.net> wrote:
> Dne ?etrtek, 08. februar 2018 ob 10:15:35 CET je Icenowy Zheng napisal(a):
>> ? 2018-02-08 17:00?Maxime Ripard ???
>>
>> > On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> >> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> >> factor and GPIO holes similar to Raspberry Pi Zero.
>> >>
>> >> It features:
>> >> - Allwinner H2+ SoC
>> >> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> >> - Ampak AP6212 Wi-Fi/Bluetooth module
>> >> - MicroSD slot
>> >> - Two MicroUSB Type-B ports (one can only be used to power the board
>> >> and
>> >>
>> >> the other features OTG functionality)
>> >>
>> >> - Two keys, a reset and a GPIO-connected key.
>> >> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> >> - CSI connector to connect the camera sensor provided by Sinovoip.
>> >>
>> >> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> >> ---
>> >> Changes in v4:
>> >> - Use SPDX license identifier.
>> >>
>> >> Changes in v3:
>> >> - Add comments about Vbus problem in &usbphy node.
>> >>
>> >> Changes in v2:
>> >> - Use high active SD card detect on the production batch.
>> >>
>> >> arch/arm/boot/dts/Makefile | 1 +
>> >> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> >>
>> >> +++++++++++++++++++++
>> >>
>> >> 2 files changed, 127 insertions(+)
>> >> create mode 100644
>> >>
>> >> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >>
>> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> >> index ade7a38543dc..d5a17e6e8b0f 100644
>> >> --- a/arch/arm/boot/dts/Makefile
>> >> +++ b/arch/arm/boot/dts/Makefile
>> >> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> >>
>> >> sun8i-a83t-cubietruck-plus.dtb \
>> >> sun8i-a83t-tbs-a711.dtb \
>> >> sun8i-h2-plus-orangepi-r1.dtb \
>> >>
>> >> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> >>
>> >> sun8i-h2-plus-orangepi-zero.dtb \
>> >> sun8i-h3-bananapi-m2-plus.dtb \
>> >> sun8i-h3-beelink-x2.dtb \
>> >>
>> >> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> new file mode 100644
>> >> index 000000000000..e2ee65a5bf92
>> >> --- /dev/null
>> >> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> >> @@ -0,0 +1,126 @@
>> >> +/*
>> >> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> >> + *
>> >> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> >> + * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
>> >> + *
>> >> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> >
>> > Sorry to be a bit picky about this, but this should be your very first
>> > line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
>> > example.
>>
>> I think it's also OK here, see
>> arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Lincesing rules [1] says it should be in first possible line which can contain
> comment.
>
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/
> Documentation/process/license-rules.rst#n57
I confess I only read the license line rule some time after I posted that
patch.
ChenYu
>>
>> > Thanks!
>> > Maxime
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "linux-sunxi" group. To unsubscribe from this group and stop receiving
>> emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.
>
>
>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2018-02-08 9:41 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-02-06 13:16 [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board Icenowy Zheng
2018-02-06 13:16 ` Icenowy Zheng
2018-02-06 13:16 ` Icenowy Zheng
2018-02-08 9:00 ` Maxime Ripard
2018-02-08 9:00 ` Maxime Ripard
2018-02-08 9:15 ` Icenowy Zheng
2018-02-08 9:15 ` Icenowy Zheng
2018-02-08 9:15 ` Icenowy Zheng
2018-02-08 9:28 ` [linux-sunxi] " Jernej Škrabec
2018-02-08 9:28 ` Jernej Škrabec
2018-02-08 9:28 ` Jernej Škrabec
2018-02-08 9:41 ` [linux-sunxi] " Chen-Yu Tsai
2018-02-08 9:41 ` Chen-Yu Tsai
2018-02-08 9:41 ` Chen-Yu Tsai
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.