[PATCH 0/3] Use interconnect API in MDSS on SDM845

[PATCH 0/3] Use interconnect API in MDSS on SDM845

[Sravanthi Kollukuduru]

The interconnect API provides an interface for consumer drivers to express
their bandwidth needs in the SoC. This data is aggregated and the on-chip
interconnect hardware is configured to the appropriate power/performance
profile.

MDSS is one of the interconnect consumers which uses the interconnect APIs
to get the path between endpoints and set its bandwidth requirements
for the given interconnected path.

Subsequently, there is a clean up patch to remove all the references
of the DPU custom bus scaling.

There is corresponding DT patch with the source and destination ports
defined for display driver which will be sent separately.

Sravanthi Kollukuduru (3):
  drm/msm/dpu: clean up references of DPU custom bus scaling
  drm/msm/dpu: Integrate interconnect API in MDSS
  dt-bindings: msm/disp: Introduce interconnect bindings for MDSS on
    SDM845

 .../devicetree/bindings/display/msm/dpu.txt        |   8 ++
 drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c      | 157 +++++++++------------
 drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h      |   4 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c           |   1 -
 drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c           |  56 +++++++-
 drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c   |  47 ++----
 drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h   |  68 ---------
 drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h          |  21 +--
 8 files changed, 143 insertions(+), 219 deletions(-)

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

[PATCH 1/3] drm/msm/dpu: clean up references of DPU custom bus scaling

[Sravanthi Kollukuduru]

Since the upstream interconnect bus framework has landed
upstream, the existing references of custom bus scaling
needs to be cleaned up.

Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c    | 157 ++++++++++-------------
 drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h    |   4 +-
 drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c         |   1 -
 drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c |  47 ++-----
 drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h |  68 ----------
 drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h        |  21 +--
 6 files changed, 83 insertions(+), 215 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
index 41c5191f9056..4ee6f0dd14f7 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
@@ -90,7 +90,6 @@ static void _dpu_core_perf_calc_crtc(struct dpu_kms *kms,
 		struct dpu_core_perf_params *perf)
 {
 	struct dpu_crtc_state *dpu_cstate;
-	int i;
 
 	if (!kms || !kms->catalog || !crtc || !state || !perf) {
 		DPU_ERROR("invalid parameters\n");
@@ -101,35 +100,24 @@ static void _dpu_core_perf_calc_crtc(struct dpu_kms *kms,
 	memset(perf, 0, sizeof(struct dpu_core_perf_params));
 
 	if (!dpu_cstate->bw_control) {
-		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-			perf->bw_ctl[i] = kms->catalog->perf.max_bw_high *
+		perf->bw_ctl = kms->catalog->perf.max_bw_high *
 					1000ULL;
-			perf->max_per_pipe_ib[i] = perf->bw_ctl[i];
-		}
+		perf->max_per_pipe_ib = perf->bw_ctl;
 		perf->core_clk_rate = kms->perf.max_core_clk_rate;
 	} else if (kms->perf.perf_tune.mode == DPU_PERF_MODE_MINIMUM) {
-		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-			perf->bw_ctl[i] = 0;
-			perf->max_per_pipe_ib[i] = 0;
-		}
+		perf->bw_ctl = 0;
+		perf->max_per_pipe_ib = 0;
 		perf->core_clk_rate = 0;
 	} else if (kms->perf.perf_tune.mode == DPU_PERF_MODE_FIXED) {
-		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-			perf->bw_ctl[i] = kms->perf.fix_core_ab_vote;
-			perf->max_per_pipe_ib[i] = kms->perf.fix_core_ib_vote;
-		}
+		perf->bw_ctl = kms->perf.fix_core_ab_vote;
+		perf->max_per_pipe_ib = kms->perf.fix_core_ib_vote;
 		perf->core_clk_rate = kms->perf.fix_core_clk_rate;
 	}
 
 	DPU_DEBUG(
-		"crtc=%d clk_rate=%llu core_ib=%llu core_ab=%llu llcc_ib=%llu llcc_ab=%llu mem_ib=%llu mem_ab=%llu\n",
+		"crtc=%d clk_rate=%llu core_ib=%llu core_ab=%llu\n",
 			crtc->base.id, perf->core_clk_rate,
-			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_MNOC],
-			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MNOC],
-			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_LLCC],
-			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_LLCC],
-			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_EBI],
-			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_EBI]);
+			perf->max_per_pipe_ib, perf->bw_ctl);
 }
 
 int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
@@ -142,7 +130,6 @@ int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
 	struct dpu_crtc_state *dpu_cstate;
 	struct drm_crtc *tmp_crtc;
 	struct dpu_kms *kms;
-	int i;
 
 	if (!crtc || !state) {
 		DPU_ERROR("invalid crtc\n");
@@ -164,31 +151,28 @@ int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
 	/* obtain new values */
 	_dpu_core_perf_calc_crtc(kms, crtc, state, &dpu_cstate->new_perf);
 
-	for (i = DPU_POWER_HANDLE_DBUS_ID_MNOC;
-			i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-		bw_sum_of_intfs = dpu_cstate->new_perf.bw_ctl[i];
-		curr_client_type = dpu_crtc_get_client_type(crtc);
+	bw_sum_of_intfs = dpu_cstate->new_perf.bw_ctl;
+	curr_client_type = dpu_crtc_get_client_type(crtc);
 
-		drm_for_each_crtc(tmp_crtc, crtc->dev) {
-			if (_dpu_core_perf_crtc_is_power_on(tmp_crtc) &&
-			    (dpu_crtc_get_client_type(tmp_crtc) ==
-					    curr_client_type) &&
-			    (tmp_crtc != crtc)) {
-				struct dpu_crtc_state *tmp_cstate =
-					to_dpu_crtc_state(tmp_crtc->state);
-
-				DPU_DEBUG("crtc:%d bw:%llu ctrl:%d\n",
-					tmp_crtc->base.id,
-					tmp_cstate->new_perf.bw_ctl[i],
-					tmp_cstate->bw_control);
-				/*
-				 * For bw check only use the bw if the
-				 * atomic property has been already set
-				 */
-				if (tmp_cstate->bw_control)
-					bw_sum_of_intfs +=
-						tmp_cstate->new_perf.bw_ctl[i];
-			}
+	drm_for_each_crtc(tmp_crtc, crtc->dev) {
+		if (_dpu_core_perf_crtc_is_power_on(tmp_crtc) &&
+		    (dpu_crtc_get_client_type(tmp_crtc) ==
+				    curr_client_type) &&
+		    (tmp_crtc != crtc)) {
+			struct dpu_crtc_state *tmp_cstate =
+				to_dpu_crtc_state(tmp_crtc->state);
+
+			DPU_DEBUG("crtc:%d bw:%llu ctrl:%d\n",
+				tmp_crtc->base.id,
+				tmp_cstate->new_perf.bw_ctl,
+				tmp_cstate->bw_control);
+			/*
+			 * For bw check only use the bw if the
+			 * atomic property has been already set
+			 */
+			if (tmp_cstate->bw_control)
+				bw_sum_of_intfs +=
+					tmp_cstate->new_perf.bw_ctl;
 		}
 
 		/* convert bandwidth to kb */
@@ -219,9 +203,9 @@ int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
 }
 
 static int _dpu_core_perf_crtc_update_bus(struct dpu_kms *kms,
-		struct drm_crtc *crtc, u32 bus_id)
+		struct drm_crtc *crtc)
 {
-	struct dpu_core_perf_params perf = { { 0 } };
+	struct dpu_core_perf_params perf = { 0 };
 	enum dpu_crtc_client_type curr_client_type
 					= dpu_crtc_get_client_type(crtc);
 	struct drm_crtc *tmp_crtc;
@@ -234,13 +218,12 @@ static int _dpu_core_perf_crtc_update_bus(struct dpu_kms *kms,
 				dpu_crtc_get_client_type(tmp_crtc)) {
 			dpu_cstate = to_dpu_crtc_state(tmp_crtc->state);
 
-			perf.max_per_pipe_ib[bus_id] =
-				max(perf.max_per_pipe_ib[bus_id],
-				dpu_cstate->new_perf.max_per_pipe_ib[bus_id]);
+			perf.max_per_pipe_ib =
+				max(perf.max_per_pipe_ib,
+				dpu_cstate->new_perf.max_per_pipe_ib);
 
-			DPU_DEBUG("crtc=%d bus_id=%d bw=%llu\n",
-				tmp_crtc->base.id, bus_id,
-				dpu_cstate->new_perf.bw_ctl[bus_id]);
+			DPU_DEBUG("crtc=%d bw=%llu\n",
+				tmp_crtc->base.id, dpu_cstate->new_perf.bw_ctl);
 		}
 	}
 	return ret;
@@ -260,7 +243,6 @@ void dpu_core_perf_crtc_release_bw(struct drm_crtc *crtc)
 	struct dpu_crtc *dpu_crtc;
 	struct dpu_crtc_state *dpu_cstate;
 	struct dpu_kms *kms;
-	int i;
 
 	if (!crtc) {
 		DPU_ERROR("invalid crtc\n");
@@ -296,10 +278,8 @@ void dpu_core_perf_crtc_release_bw(struct drm_crtc *crtc)
 	if (kms->perf.enable_bw_release) {
 		trace_dpu_cmd_release_bw(crtc->base.id);
 		DPU_DEBUG("Release BW crtc=%d\n", crtc->base.id);
-		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-			dpu_crtc->cur_perf.bw_ctl[i] = 0;
-			_dpu_core_perf_crtc_update_bus(kms, crtc, i);
-		}
+		dpu_crtc->cur_perf.bw_ctl = 0;
+		_dpu_core_perf_crtc_update_bus(kms, crtc);
 	}
 }
 
@@ -342,11 +322,10 @@ int dpu_core_perf_crtc_update(struct drm_crtc *crtc,
 		int params_changed, bool stop_req)
 {
 	struct dpu_core_perf_params *new, *old;
-	int update_bus = 0, update_clk = 0;
+	bool update_bus = false, update_clk = false;
 	u64 clk_rate = 0;
 	struct dpu_crtc *dpu_crtc;
 	struct dpu_crtc_state *dpu_cstate;
-	int i;
 	struct msm_drm_private *priv;
 	struct dpu_kms *kms;
 	int ret;
@@ -373,7 +352,6 @@ int dpu_core_perf_crtc_update(struct drm_crtc *crtc,
 	new = &dpu_cstate->new_perf;
 
 	if (_dpu_core_perf_crtc_is_power_on(crtc) && !stop_req) {
-		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
 			/*
 			 * cases for bus bandwidth update.
 			 * 1. new bandwidth vote - "ab or ib vote" is higher
@@ -381,23 +359,22 @@ int dpu_core_perf_crtc_update(struct drm_crtc *crtc,
 			 * 2. new bandwidth vote - "ab or ib vote" is lower
 			 *    than current vote at end of commit or stop.
 			 */
-			if ((params_changed && ((new->bw_ctl[i] >
-						old->bw_ctl[i]) ||
-				  (new->max_per_pipe_ib[i] >
-						old->max_per_pipe_ib[i]))) ||
-			    (!params_changed && ((new->bw_ctl[i] <
-						old->bw_ctl[i]) ||
-				  (new->max_per_pipe_ib[i] <
-						old->max_per_pipe_ib[i])))) {
+			if ((params_changed && ((new->bw_ctl >
+						old->bw_ctl) ||
+				  (new->max_per_pipe_ib >
+						old->max_per_pipe_ib))) ||
+			    (!params_changed && ((new->bw_ctl <
+						old->bw_ctl) ||
+				  (new->max_per_pipe_ib <
+						old->max_per_pipe_ib)))) {
 				DPU_DEBUG(
 					"crtc=%d p=%d new_bw=%llu,old_bw=%llu\n",
 					crtc->base.id, params_changed,
-					new->bw_ctl[i], old->bw_ctl[i]);
-				old->bw_ctl[i] = new->bw_ctl[i];
-				old->max_per_pipe_ib[i] =
-						new->max_per_pipe_ib[i];
-				update_bus |= BIT(i);
-			}
+					new->bw_ctl, old->bw_ctl);
+				old->bw_ctl = new->bw_ctl;
+				old->max_per_pipe_ib =
+						new->max_per_pipe_ib;
+				update_bus = true;
 		}
 
 		if ((params_changed &&
@@ -405,30 +382,26 @@ int dpu_core_perf_crtc_update(struct drm_crtc *crtc,
 				(!params_changed &&
 				(new->core_clk_rate < old->core_clk_rate))) {
 			old->core_clk_rate = new->core_clk_rate;
-			update_clk = 1;
+			update_clk = true;
 		}
 	} else {
 		DPU_DEBUG("crtc=%d disable\n", crtc->base.id);
 		memset(old, 0, sizeof(*old));
 		memset(new, 0, sizeof(*new));
-		update_bus = ~0;
-		update_clk = 1;
+		update_bus = true;
+		update_clk = true;
 	}
+
 	trace_dpu_perf_crtc_update(crtc->base.id,
-				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MNOC],
-				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_LLCC],
-				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_EBI],
-				new->core_clk_rate, stop_req,
-				update_bus, update_clk);
-
-	for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
-		if (update_bus & BIT(i)) {
-			ret = _dpu_core_perf_crtc_update_bus(kms, crtc, i);
-			if (ret) {
-				DPU_ERROR("crtc-%d: failed to update bw vote for bus-%d\n",
-					  crtc->base.id, i);
-				return ret;
-			}
+				new->bw_ctl, new->core_clk_rate,
+				stop_req, update_bus, update_clk);
+
+	if (update_bus) {
+		ret = _dpu_core_perf_crtc_update_bus(kms, crtc);
+		if (ret) {
+			DPU_ERROR("crtc-%d: failed to update bus bw vote\n",
+				  crtc->base.id);
+			return ret;
 		}
 	}
 
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
index fbcbe0c7527a..0fb276929dc5 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
@@ -30,8 +30,8 @@
  * @core_clk_rate: core clock rate request
  */
 struct dpu_core_perf_params {
-	u64 max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_MAX];
-	u64 bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MAX];
+	u64 max_per_pipe_ib;
+	u64 bw_ctl;
 	u64 core_clk_rate;
 };
 
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
index d4530d60767b..4ecb6f96e6ba 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
@@ -1450,7 +1450,6 @@ static int dpu_crtc_debugfs_state_show(struct seq_file *s, void *v)
 {
 	struct drm_crtc *crtc = (struct drm_crtc *) s->private;
 	struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc);
-	int i;
 
 	seq_printf(s, "client type: %d\n", dpu_crtc_get_client_type(crtc));
 	seq_printf(s, "intf_mode: %d\n", dpu_crtc_get_intf_mode(crtc));
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
index fc14116789f2..d58d01544731 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
@@ -24,20 +24,6 @@
 #include "dpu_power_handle.h"
 #include "dpu_trace.h"
 
-static const char *data_bus_name[DPU_POWER_HANDLE_DBUS_ID_MAX] = {
-	[DPU_POWER_HANDLE_DBUS_ID_MNOC] = "qcom,dpu-data-bus",
-	[DPU_POWER_HANDLE_DBUS_ID_LLCC] = "qcom,dpu-llcc-bus",
-	[DPU_POWER_HANDLE_DBUS_ID_EBI] = "qcom,dpu-ebi-bus",
-};
-
-const char *dpu_power_handle_get_dbus_name(u32 bus_id)
-{
-	if (bus_id < DPU_POWER_HANDLE_DBUS_ID_MAX)
-		return data_bus_name[bus_id];
-
-	return NULL;
-}
-
 static void dpu_power_event_trigger_locked(struct dpu_power_handle *phandle,
 		u32 event_type)
 {
@@ -66,7 +52,6 @@ struct dpu_power_client *dpu_power_client_create(
 
 	mutex_lock(&phandle->phandle_lock);
 	strlcpy(client->name, client_name, MAX_CLIENT_NAME_LEN);
-	client->usecase_ndx = VOTE_INDEX_DISABLE;
 	client->id = id;
 	client->active = true;
 	pr_debug("client %s created:%pK id :%d\n", client_name,
@@ -143,8 +128,6 @@ int dpu_power_resource_enable(struct dpu_power_handle *phandle,
 	struct dpu_power_client *pclient, bool enable)
 {
 	bool changed = false;
-	u32 max_usecase_ndx = VOTE_INDEX_DISABLE, prev_usecase_ndx;
-	struct dpu_power_client *client;
 	u32 event_type;
 
 	if (!phandle || !pclient) {
@@ -153,31 +136,19 @@ int dpu_power_resource_enable(struct dpu_power_handle *phandle,
 	}
 
 	mutex_lock(&phandle->phandle_lock);
-	if (enable)
+	if (enable) {
 		pclient->refcount++;
-	else if (pclient->refcount)
+		if (pclient->refcount == 1)
+			changed = true;
+	} else if (pclient->refcount) {
 		pclient->refcount--;
-
-	if (pclient->refcount)
-		pclient->usecase_ndx = VOTE_INDEX_LOW;
-	else
-		pclient->usecase_ndx = VOTE_INDEX_DISABLE;
-
-	list_for_each_entry(client, &phandle->power_client_clist, list) {
-		if (client->usecase_ndx < VOTE_INDEX_MAX &&
-		    client->usecase_ndx > max_usecase_ndx)
-			max_usecase_ndx = client->usecase_ndx;
-	}
-
-	if (phandle->current_usecase_ndx != max_usecase_ndx) {
-		changed = true;
-		prev_usecase_ndx = phandle->current_usecase_ndx;
-		phandle->current_usecase_ndx = max_usecase_ndx;
+		if (!pclient->refcount)
+			changed = true;
 	}
 
-	pr_debug("%pS: changed=%d current idx=%d request client %s id:%u enable:%d refcount:%d\n",
-		__builtin_return_address(0), changed, max_usecase_ndx,
-		pclient->name, pclient->id, enable, pclient->refcount);
+	pr_debug("%pS:changed=%d client %s id:%u enable:%d refcount:%d\n",
+		__builtin_return_address(0), changed, pclient->name,
+		pclient->id, enable, pclient->refcount);
 
 	if (!changed)
 		goto end;
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
index a65b7a297f21..b1a5ae4d6f4e 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
@@ -16,76 +16,28 @@
 
 #define MAX_CLIENT_NAME_LEN 128
 
-#define DPU_POWER_HANDLE_ENABLE_BUS_AB_QUOTA	0
-#define DPU_POWER_HANDLE_DISABLE_BUS_AB_QUOTA	0
-#define DPU_POWER_HANDLE_ENABLE_BUS_IB_QUOTA	1600000000
-#define DPU_POWER_HANDLE_DISABLE_BUS_IB_QUOTA	0
-
 #include "dpu_io_util.h"
 
 /* events will be triggered on power handler enable/disable */
 #define DPU_POWER_EVENT_DISABLE	BIT(0)
 #define DPU_POWER_EVENT_ENABLE	BIT(1)
 
-/**
- * mdss_bus_vote_type: register bus vote type
- * VOTE_INDEX_DISABLE: removes the client vote
- * VOTE_INDEX_LOW: keeps the lowest vote for register bus
- * VOTE_INDEX_MAX: invalid
- */
-enum mdss_bus_vote_type {
-	VOTE_INDEX_DISABLE,
-	VOTE_INDEX_LOW,
-	VOTE_INDEX_MAX,
-};
-
-/**
- * enum dpu_power_handle_data_bus_client - type of axi bus clients
- * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_RT: core real-time bus client
- * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_NRT: core non-real-time bus client
- * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX: maximum number of bus client type
- */
-enum dpu_power_handle_data_bus_client {
-	DPU_POWER_HANDLE_DATA_BUS_CLIENT_RT,
-	DPU_POWER_HANDLE_DATA_BUS_CLIENT_NRT,
-	DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX
-};
-
-/**
- * enum DPU_POWER_HANDLE_DBUS_ID - data bus identifier
- * @DPU_POWER_HANDLE_DBUS_ID_MNOC: DPU/MNOC data bus
- * @DPU_POWER_HANDLE_DBUS_ID_LLCC: MNOC/LLCC data bus
- * @DPU_POWER_HANDLE_DBUS_ID_EBI: LLCC/EBI data bus
- */
-enum DPU_POWER_HANDLE_DBUS_ID {
-	DPU_POWER_HANDLE_DBUS_ID_MNOC,
-	DPU_POWER_HANDLE_DBUS_ID_LLCC,
-	DPU_POWER_HANDLE_DBUS_ID_EBI,
-	DPU_POWER_HANDLE_DBUS_ID_MAX,
-};
-
 /**
  * struct dpu_power_client: stores the power client for dpu driver
  * @name:	name of the client
- * @usecase_ndx: current regs bus vote type
  * @refcount:	current refcount if multiple modules are using same
  *              same client for enable/disable. Power module will
  *              aggregate the refcount and vote accordingly for this
  *              client.
  * @id:		assigned during create. helps for debugging.
  * @list:	list to attach power handle master list
- * @ab:         arbitrated bandwidth for each bus client
- * @ib:         instantaneous bandwidth for each bus client
  * @active:	inidcates the state of dpu power handle
  */
 struct dpu_power_client {
 	char name[MAX_CLIENT_NAME_LEN];
-	short usecase_ndx;
 	short refcount;
 	u32 id;
 	struct list_head list;
-	u64 ab[DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX];
-	u64 ib[DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX];
 	bool active;
 };
 
@@ -112,14 +64,12 @@ struct dpu_power_event {
  * @client_clist: master list to store all clients
  * @phandle_lock: lock to synchronize the enable/disable
  * @dev: pointer to device structure
- * @usecase_ndx: current usecase index
  * @event_list: current power handle event list
  */
 struct dpu_power_handle {
 	struct list_head power_client_clist;
 	struct mutex phandle_lock;
 	struct device *dev;
-	u32 current_usecase_ndx;
 	struct list_head event_list;
 };
 
@@ -172,17 +122,6 @@ void dpu_power_client_destroy(struct dpu_power_handle *phandle,
 int dpu_power_resource_enable(struct dpu_power_handle *pdata,
 	struct dpu_power_client *pclient, bool enable);
 
-/**
- * dpu_power_data_bus_bandwidth_ctrl() - control data bus bandwidth enable
- * @phandle:  power handle containing the resources
- * @client: client information to bandwidth control
- * @enable: true to enable bandwidth for data base
- *
- * Return: none
- */
-void dpu_power_data_bus_bandwidth_ctrl(struct dpu_power_handle *phandle,
-		struct dpu_power_client *pclient, int enable);
-
 /**
  * dpu_power_handle_register_event - register a callback function for an event.
  *	Clients can register for multiple events with a single register.
@@ -207,11 +146,4 @@ struct dpu_power_event *dpu_power_handle_register_event(
 void dpu_power_handle_unregister_event(struct dpu_power_handle *phandle,
 		struct dpu_power_event *event);
 
-/**
- * dpu_power_handle_get_dbus_name - get name of given data bus identifier
- * @bus_id:	data bus identifier
- * Return:	Pointer to name string if success; NULL otherwise
- */
-const char *dpu_power_handle_get_dbus_name(u32 bus_id);
-
 #endif /* _DPU_POWER_HANDLE_H_ */
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
index 636b31b0d311..72a32e9b5ca5 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
@@ -167,16 +167,13 @@ TRACE_EVENT(dpu_trace_counter,
 )
 
 TRACE_EVENT(dpu_perf_crtc_update,
-	TP_PROTO(u32 crtc, u64 bw_ctl_mnoc, u64 bw_ctl_llcc,
-			u64 bw_ctl_ebi, u32 core_clk_rate,
-			bool stop_req, u32 update_bus, u32 update_clk),
-	TP_ARGS(crtc, bw_ctl_mnoc, bw_ctl_llcc, bw_ctl_ebi, core_clk_rate,
+	TP_PROTO(u32 crtc, u64 bw_ctl, u32 core_clk_rate,
+			bool stop_req, bool update_bus, bool update_clk),
+	TP_ARGS(crtc, bw_ctl, core_clk_rate,
 		stop_req, update_bus, update_clk),
 	TP_STRUCT__entry(
 			__field(u32, crtc)
-			__field(u64, bw_ctl_mnoc)
-			__field(u64, bw_ctl_llcc)
-			__field(u64, bw_ctl_ebi)
+			__field(u64, bw_ctl)
 			__field(u32, core_clk_rate)
 			__field(bool, stop_req)
 			__field(u32, update_bus)
@@ -184,20 +181,16 @@ TRACE_EVENT(dpu_perf_crtc_update,
 	),
 	TP_fast_assign(
 			__entry->crtc = crtc;
-			__entry->bw_ctl_mnoc = bw_ctl_mnoc;
-			__entry->bw_ctl_llcc = bw_ctl_llcc;
-			__entry->bw_ctl_ebi = bw_ctl_ebi;
+			__entry->bw_ctl = bw_ctl;
 			__entry->core_clk_rate = core_clk_rate;
 			__entry->stop_req = stop_req;
 			__entry->update_bus = update_bus;
 			__entry->update_clk = update_clk;
 	),
 	 TP_printk(
-		"crtc=%d bw_mnoc=%llu bw_llcc=%llu bw_ebi=%llu clk_rate=%u stop_req=%d u_bus=%d u_clk=%d",
+		"crtc=%d bw_ctl=%llu clk_rate=%u stop_req=%d u_bus=%d u_clk=%d",
 			__entry->crtc,
-			__entry->bw_ctl_mnoc,
-			__entry->bw_ctl_llcc,
-			__entry->bw_ctl_ebi,
+			__entry->bw_ctl,
 			__entry->core_clk_rate,
 			__entry->stop_req,
 			__entry->update_bus,
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

[PATCH 2/3] drm/msm/dpu: Integrate interconnect API in MDSS

[Sravanthi Kollukuduru]

The interconnect framework is designed to provide a
standard kernel interface to control the settings of
the interconnects on a SoC.

The interconnect API uses a consumer/provider-based model,
where the providers are the interconnect buses and the
consumers could be various drivers.

MDSS is one of the interconnect consumers which uses the
interconnect APIs to get the path between endpoints and
set its bandwidth/latency/QoS requirements for the given
interconnected path.

Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c | 56 +++++++++++++++++++++++++++++---
 1 file changed, 52 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
index 2235ef8129f4..8391e5c1e559 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
@@ -4,10 +4,12 @@
  */
 
 #include "dpu_kms.h"
+#include <linux/interconnect.h>
 
 #define to_dpu_mdss(x) container_of(x, struct dpu_mdss, base)
 
 #define HW_INTR_STATUS			0x0010
+#define MAX_AXI_PORT_COUNT 3
 
 struct dpu_mdss {
 	struct msm_mdss base;
@@ -16,8 +18,36 @@ struct dpu_mdss {
 	u32 hwversion;
 	struct dss_module_power mp;
 	struct dpu_irq_controller irq_controller;
+	struct icc_path *path[MAX_AXI_PORT_COUNT];
+	u32 num_paths;
 };
 
+static int dpu_mdss_parse_data_bus_icc_path(
+		struct drm_device *dev, struct dpu_mdss *dpu_mdss)
+{
+	struct icc_path *path0 = of_icc_get(dev->dev, "port0");
+	struct icc_path *path1 = of_icc_get(dev->dev, "port1");
+	int total_num_paths  = 0;
+
+	if (IS_ERR(path0))
+		return PTR_ERR(path0);
+
+	dpu_mdss->path[0] = path0;
+	total_num_paths = 1;
+
+	if (!IS_ERR(path1)) {
+		dpu_mdss->path[1] = path1;
+		total_num_paths++;
+	}
+
+	if (total_num_paths  > MAX_AXI_PORT_COUNT)
+		return -EINVAL;
+
+	dpu_mdss->num_paths = total_num_paths;
+
+	return 0;
+}
+
 static irqreturn_t dpu_mdss_irq(int irq, void *arg)
 {
 	struct dpu_mdss *dpu_mdss = arg;
@@ -127,7 +157,12 @@ static int dpu_mdss_enable(struct msm_mdss *mdss)
 {
 	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
 	struct dss_module_power *mp = &dpu_mdss->mp;
-	int ret;
+	int ret, i;
+	u64 ab = (dpu_mdss->num_paths) ? 6800000000/dpu_mdss->num_paths : 0;
+	u64 ib = 6800000000;
+
+	for (i = 0; i < dpu_mdss->num_paths; i++)
+		icc_set(dpu_mdss->path[i], ab, ib);
 
 	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, true);
 	if (ret)
@@ -140,12 +175,15 @@ static int dpu_mdss_disable(struct msm_mdss *mdss)
 {
 	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
 	struct dss_module_power *mp = &dpu_mdss->mp;
-	int ret;
+	int ret, i;
 
 	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, false);
 	if (ret)
 		DPU_ERROR("clock disable failed, ret:%d\n", ret);
 
+	for (i = 0; i < dpu_mdss->num_paths; i++)
+		icc_set(dpu_mdss->path[i], 0, 0);
+
 	return ret;
 }
 
@@ -155,6 +193,7 @@ static void dpu_mdss_destroy(struct drm_device *dev)
 	struct msm_drm_private *priv = dev->dev_private;
 	struct dpu_mdss *dpu_mdss = to_dpu_mdss(priv->mdss);
 	struct dss_module_power *mp = &dpu_mdss->mp;
+	int i;
 
 	_dpu_mdss_irq_domain_fini(dpu_mdss);
 
@@ -163,6 +202,9 @@ static void dpu_mdss_destroy(struct drm_device *dev)
 	msm_dss_put_clk(mp->clk_config, mp->num_clk);
 	devm_kfree(&pdev->dev, mp->clk_config);
 
+	for (i = 0; i < dpu_mdss->num_paths; i++)
+		icc_put(dpu_mdss->path[i]);
+
 	if (dpu_mdss->mmio)
 		devm_iounmap(&pdev->dev, dpu_mdss->mmio);
 	dpu_mdss->mmio = NULL;
@@ -203,6 +245,12 @@ int dpu_mdss_init(struct drm_device *dev)
 	}
 	dpu_mdss->mmio_len = resource_size(res);
 
+	ret = dpu_mdss_parse_data_bus_icc_path(dev, dpu_mdss);
+	if (ret) {
+		DPU_ERROR("failed to parse icc path, ret=%d\n", ret);
+		return ret;
+	}
+
 	mp = &dpu_mdss->mp;
 	ret = msm_dss_parse_clock(pdev, mp);
 	if (ret) {
@@ -224,14 +272,14 @@ int dpu_mdss_init(struct drm_device *dev)
 		goto irq_error;
 	}
 
+	priv->mdss = &dpu_mdss->base;
+
 	pm_runtime_enable(dev->dev);
 
 	pm_runtime_get_sync(dev->dev);
 	dpu_mdss->hwversion = readl_relaxed(dpu_mdss->mmio);
 	pm_runtime_put_sync(dev->dev);
 
-	priv->mdss = &dpu_mdss->base;
-
 	return ret;
 
 irq_error:
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

[PATCH 3/3] dt-bindings: msm/disp: Introduce interconnect bindings for MDSS on SDM845

[Sravanthi Kollukuduru]

Add interconnect properties such as interconnect provider specifier
, the edge source and destination ports which are required by the
interconnect API to configure interconnect path for MDSS.

Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
---
 Documentation/devicetree/bindings/display/msm/dpu.txt | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
index ad2e8830324e..abd4d99b5030 100644
--- a/Documentation/devicetree/bindings/display/msm/dpu.txt
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -28,6 +28,11 @@ Required properties:
 - #address-cells: number of address cells for the MDSS children. Should be 1.
 - #size-cells: Should be 1.
 - ranges: parent bus address space is the same as the child bus address space.
+- interconnects : pairs of phandles and interconnect provider specifier to
+  denote the edge source and destination ports of the interconnect path.
+- interconnect-names : list of interconnect path name strings sorted in the
+  same order as the interconnects property. Consumers drivers will use
+  interconnect-names to match interconnect paths with interconnect specifiers.
 
 Optional properties:
 - assigned-clocks: list of clock specifiers for clocks needing rate assignment
@@ -86,6 +91,9 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 
+		interconnects = <&qnoc 38 &qnoc 512>;
+		interconnect-names = "port0";
+
 		iommus = <&apps_iommu 0>;
 
 		#address-cells = <2>;
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

Re: [PATCH 2/3] drm/msm/dpu: Integrate interconnect API in MDSS

[Jordan Crouse]

On Mon, Oct 08, 2018 at 02:57:29PM +0530, Sravanthi Kollukuduru wrote:
> The interconnect framework is designed to provide a
> standard kernel interface to control the settings of
> the interconnects on a SoC.
> 
> The interconnect API uses a consumer/provider-based model,
> where the providers are the interconnect buses and the
> consumers could be various drivers.
> 
> MDSS is one of the interconnect consumers which uses the
> interconnect APIs to get the path between endpoints and
> set its bandwidth/latency/QoS requirements for the given
> interconnected path.
> 
> Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c | 56 +++++++++++++++++++++++++++++---
>  1 file changed, 52 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
> index 2235ef8129f4..8391e5c1e559 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
> @@ -4,10 +4,12 @@
>   */
>  
>  #include "dpu_kms.h"
> +#include <linux/interconnect.h>
>  
>  #define to_dpu_mdss(x) container_of(x, struct dpu_mdss, base)
>  
>  #define HW_INTR_STATUS			0x0010
> +#define MAX_AXI_PORT_COUNT 3
>  
>  struct dpu_mdss {
>  	struct msm_mdss base;
> @@ -16,8 +18,36 @@ struct dpu_mdss {
>  	u32 hwversion;
>  	struct dss_module_power mp;
>  	struct dpu_irq_controller irq_controller;
> +	struct icc_path *path[MAX_AXI_PORT_COUNT];
> +	u32 num_paths;
>  };
>  
> +static int dpu_mdss_parse_data_bus_icc_path(
> +		struct drm_device *dev, struct dpu_mdss *dpu_mdss)
> +{
> +	struct icc_path *path0 = of_icc_get(dev->dev, "port0");
> +	struct icc_path *path1 = of_icc_get(dev->dev, "port1");
> +	int total_num_paths  = 0;
> +
> +	if (IS_ERR(path0))
> +		return PTR_ERR(path0);
> +
> +	dpu_mdss->path[0] = path0;
> +	total_num_paths = 1;
> +
> +	if (!IS_ERR(path1)) {
> +		dpu_mdss->path[1] = path1;
> +		total_num_paths++;
> +	}
> +
> +	if (total_num_paths  > MAX_AXI_PORT_COUNT)
> +		return -EINVAL;

Since you are using fixed names you know that by design this isn't possible.

> +	dpu_mdss->num_paths = total_num_paths;
> +
> +	return 0;
> +}
> +
>  static irqreturn_t dpu_mdss_irq(int irq, void *arg)
>  {
>  	struct dpu_mdss *dpu_mdss = arg;
> @@ -127,7 +157,12 @@ static int dpu_mdss_enable(struct msm_mdss *mdss)
>  {
>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
>  	struct dss_module_power *mp = &dpu_mdss->mp;
> -	int ret;
> +	int ret, i;
> +	u64 ab = (dpu_mdss->num_paths) ? 6800000000/dpu_mdss->num_paths : 0;
> +	u64 ib = 6800000000;
> +
> +	for (i = 0; i < dpu_mdss->num_paths; i++)
> +		icc_set(dpu_mdss->path[i], ab, ib);
>  
>  	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, true);
>  	if (ret)
> @@ -140,12 +175,15 @@ static int dpu_mdss_disable(struct msm_mdss *mdss)
>  {
>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
>  	struct dss_module_power *mp = &dpu_mdss->mp;
> -	int ret;
> +	int ret, i;
>  
>  	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, false);
>  	if (ret)
>  		DPU_ERROR("clock disable failed, ret:%d\n", ret);
>  
> +	for (i = 0; i < dpu_mdss->num_paths; i++)
> +		icc_set(dpu_mdss->path[i], 0, 0);
> +
>  	return ret;
>  }
>  
> @@ -155,6 +193,7 @@ static void dpu_mdss_destroy(struct drm_device *dev)
>  	struct msm_drm_private *priv = dev->dev_private;
>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(priv->mdss);
>  	struct dss_module_power *mp = &dpu_mdss->mp;
> +	int i;
>  
>  	_dpu_mdss_irq_domain_fini(dpu_mdss);
>  
> @@ -163,6 +202,9 @@ static void dpu_mdss_destroy(struct drm_device *dev)
>  	msm_dss_put_clk(mp->clk_config, mp->num_clk);
>  	devm_kfree(&pdev->dev, mp->clk_config);
>  
> +	for (i = 0; i < dpu_mdss->num_paths; i++)
> +		icc_put(dpu_mdss->path[i]);
> +
>  	if (dpu_mdss->mmio)
>  		devm_iounmap(&pdev->dev, dpu_mdss->mmio);
>  	dpu_mdss->mmio = NULL;
> @@ -203,6 +245,12 @@ int dpu_mdss_init(struct drm_device *dev)
>  	}
>  	dpu_mdss->mmio_len = resource_size(res);
>  
> +	ret = dpu_mdss_parse_data_bus_icc_path(dev, dpu_mdss);
> +	if (ret) {
> +		DPU_ERROR("failed to parse icc path, ret=%d\n", ret);

Depending on the ordering between DPU and interconnect, this might return
-EPROBE_DEFER for a few times before working. You should skip printing
an error message on -EPROBE_DEFER so it doesn't spam the log.

> +		return ret;
> +	}
> +
>  	mp = &dpu_mdss->mp;
>  	ret = msm_dss_parse_clock(pdev, mp);
>  	if (ret) {
> @@ -224,14 +272,14 @@ int dpu_mdss_init(struct drm_device *dev)
>  		goto irq_error;
>  	}
>  
> +	priv->mdss = &dpu_mdss->base;
> +

This seems like it might have snuck in from a different patch?

>  	pm_runtime_enable(dev->dev);
>  
>  	pm_runtime_get_sync(dev->dev);
>  	dpu_mdss->hwversion = readl_relaxed(dpu_mdss->mmio);
>  	pm_runtime_put_sync(dev->dev);
>  
> -	priv->mdss = &dpu_mdss->base;
> -
>  	return ret;
>  
>  irq_error:

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

Re: [PATCH 2/3] drm/msm/dpu: Integrate interconnect API in MDSS

[skolluku-sgV2jX0FEOL9JmXXK+q4OQ]

On 2018-10-08 20:09, Jordan Crouse wrote:
> On Mon, Oct 08, 2018 at 02:57:29PM +0530, Sravanthi Kollukuduru wrote:
>> The interconnect framework is designed to provide a
>> standard kernel interface to control the settings of
>> the interconnects on a SoC.
>> 
>> The interconnect API uses a consumer/provider-based model,
>> where the providers are the interconnect buses and the
>> consumers could be various drivers.
>> 
>> MDSS is one of the interconnect consumers which uses the
>> interconnect APIs to get the path between endpoints and
>> set its bandwidth/latency/QoS requirements for the given
>> interconnected path.
>> 
>> Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
>> ---
>>  drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c | 56 
>> +++++++++++++++++++++++++++++---
>>  1 file changed, 52 insertions(+), 4 deletions(-)
>> 
>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c 
>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
>> index 2235ef8129f4..8391e5c1e559 100644
>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_mdss.c
>> @@ -4,10 +4,12 @@
>>   */
>> 
>>  #include "dpu_kms.h"
>> +#include <linux/interconnect.h>
>> 
>>  #define to_dpu_mdss(x) container_of(x, struct dpu_mdss, base)
>> 
>>  #define HW_INTR_STATUS			0x0010
>> +#define MAX_AXI_PORT_COUNT 3
>> 
>>  struct dpu_mdss {
>>  	struct msm_mdss base;
>> @@ -16,8 +18,36 @@ struct dpu_mdss {
>>  	u32 hwversion;
>>  	struct dss_module_power mp;
>>  	struct dpu_irq_controller irq_controller;
>> +	struct icc_path *path[MAX_AXI_PORT_COUNT];
>> +	u32 num_paths;
>>  };
>> 
>> +static int dpu_mdss_parse_data_bus_icc_path(
>> +		struct drm_device *dev, struct dpu_mdss *dpu_mdss)
>> +{
>> +	struct icc_path *path0 = of_icc_get(dev->dev, "port0");
>> +	struct icc_path *path1 = of_icc_get(dev->dev, "port1");
>> +	int total_num_paths  = 0;
>> +
>> +	if (IS_ERR(path0))
>> +		return PTR_ERR(path0);
>> +
>> +	dpu_mdss->path[0] = path0;
>> +	total_num_paths = 1;
>> +
>> +	if (!IS_ERR(path1)) {
>> +		dpu_mdss->path[1] = path1;
>> +		total_num_paths++;
>> +	}
>> +
>> +	if (total_num_paths  > MAX_AXI_PORT_COUNT)
>> +		return -EINVAL;
> 
> Since you are using fixed names you know that by design this isn't 
> possible.
> 
Ok, will remove the check and the macro.

>> +	dpu_mdss->num_paths = total_num_paths;
>> +
>> +	return 0;
>> +}
>> +
>>  static irqreturn_t dpu_mdss_irq(int irq, void *arg)
>>  {
>>  	struct dpu_mdss *dpu_mdss = arg;
>> @@ -127,7 +157,12 @@ static int dpu_mdss_enable(struct msm_mdss *mdss)
>>  {
>>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
>>  	struct dss_module_power *mp = &dpu_mdss->mp;
>> -	int ret;
>> +	int ret, i;
>> +	u64 ab = (dpu_mdss->num_paths) ? 6800000000/dpu_mdss->num_paths : 0;
>> +	u64 ib = 6800000000;
>> +
>> +	for (i = 0; i < dpu_mdss->num_paths; i++)
>> +		icc_set(dpu_mdss->path[i], ab, ib);
>> 
>>  	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, true);
>>  	if (ret)
>> @@ -140,12 +175,15 @@ static int dpu_mdss_disable(struct msm_mdss 
>> *mdss)
>>  {
>>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(mdss);
>>  	struct dss_module_power *mp = &dpu_mdss->mp;
>> -	int ret;
>> +	int ret, i;
>> 
>>  	ret = msm_dss_enable_clk(mp->clk_config, mp->num_clk, false);
>>  	if (ret)
>>  		DPU_ERROR("clock disable failed, ret:%d\n", ret);
>> 
>> +	for (i = 0; i < dpu_mdss->num_paths; i++)
>> +		icc_set(dpu_mdss->path[i], 0, 0);
>> +
>>  	return ret;
>>  }
>> 
>> @@ -155,6 +193,7 @@ static void dpu_mdss_destroy(struct drm_device 
>> *dev)
>>  	struct msm_drm_private *priv = dev->dev_private;
>>  	struct dpu_mdss *dpu_mdss = to_dpu_mdss(priv->mdss);
>>  	struct dss_module_power *mp = &dpu_mdss->mp;
>> +	int i;
>> 
>>  	_dpu_mdss_irq_domain_fini(dpu_mdss);
>> 
>> @@ -163,6 +202,9 @@ static void dpu_mdss_destroy(struct drm_device 
>> *dev)
>>  	msm_dss_put_clk(mp->clk_config, mp->num_clk);
>>  	devm_kfree(&pdev->dev, mp->clk_config);
>> 
>> +	for (i = 0; i < dpu_mdss->num_paths; i++)
>> +		icc_put(dpu_mdss->path[i]);
>> +
>>  	if (dpu_mdss->mmio)
>>  		devm_iounmap(&pdev->dev, dpu_mdss->mmio);
>>  	dpu_mdss->mmio = NULL;
>> @@ -203,6 +245,12 @@ int dpu_mdss_init(struct drm_device *dev)
>>  	}
>>  	dpu_mdss->mmio_len = resource_size(res);
>> 
>> +	ret = dpu_mdss_parse_data_bus_icc_path(dev, dpu_mdss);
>> +	if (ret) {
>> +		DPU_ERROR("failed to parse icc path, ret=%d\n", ret);
> 
> Depending on the ordering between DPU and interconnect, this might 
> return
> -EPROBE_DEFER for a few times before working. You should skip printing
> an error message on -EPROBE_DEFER so it doesn't spam the log.
> 
Ok, will remove it.
>> +		return ret;
>> +	}
>> +
>>  	mp = &dpu_mdss->mp;
>>  	ret = msm_dss_parse_clock(pdev, mp);
>>  	if (ret) {
>> @@ -224,14 +272,14 @@ int dpu_mdss_init(struct drm_device *dev)
>>  		goto irq_error;
>>  	}
>> 
>> +	priv->mdss = &dpu_mdss->base;
>> +
> 
> This seems like it might have snuck in from a different patch?
No, this was included as part of this patch to ensure the mdss structure 
is
intialized before the first pm runtime resume call. If not, the 
dpu_mdss_enable
will not be called which has the logic to vote for bw and subsequently, 
enable
the clocks.
> 
>>  	pm_runtime_enable(dev->dev);
>> 
>>  	pm_runtime_get_sync(dev->dev);
>>  	dpu_mdss->hwversion = readl_relaxed(dpu_mdss->mmio);
>>  	pm_runtime_put_sync(dev->dev);
>> 
>> -	priv->mdss = &dpu_mdss->base;
>> -
>>  	return ret;
>> 
>>  irq_error:
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

Re: [PATCH 1/3] drm/msm/dpu: clean up references of DPU custom bus scaling

[skolluku-sgV2jX0FEOL9JmXXK+q4OQ]

On 2018-10-08 14:57, Sravanthi Kollukuduru wrote:
> Since the upstream interconnect bus framework has landed
> upstream, the existing references of custom bus scaling
> needs to be cleaned up.
> 
> Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
> ---
>  drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c    | 157 
> ++++++++++-------------
>  drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h    |   4 +-
>  drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c         |   1 -
>  drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c |  47 ++-----
>  drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h |  68 ----------
>  drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h        |  21 +--
>  6 files changed, 83 insertions(+), 215 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
> index 41c5191f9056..4ee6f0dd14f7 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c
> @@ -90,7 +90,6 @@ static void _dpu_core_perf_calc_crtc(struct dpu_kms 
> *kms,
>  		struct dpu_core_perf_params *perf)
>  {
>  	struct dpu_crtc_state *dpu_cstate;
> -	int i;
> 
>  	if (!kms || !kms->catalog || !crtc || !state || !perf) {
>  		DPU_ERROR("invalid parameters\n");
> @@ -101,35 +100,24 @@ static void _dpu_core_perf_calc_crtc(struct 
> dpu_kms *kms,
>  	memset(perf, 0, sizeof(struct dpu_core_perf_params));
> 
>  	if (!dpu_cstate->bw_control) {
> -		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -			perf->bw_ctl[i] = kms->catalog->perf.max_bw_high *
> +		perf->bw_ctl = kms->catalog->perf.max_bw_high *
>  					1000ULL;
> -			perf->max_per_pipe_ib[i] = perf->bw_ctl[i];
> -		}
> +		perf->max_per_pipe_ib = perf->bw_ctl;
>  		perf->core_clk_rate = kms->perf.max_core_clk_rate;
>  	} else if (kms->perf.perf_tune.mode == DPU_PERF_MODE_MINIMUM) {
> -		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -			perf->bw_ctl[i] = 0;
> -			perf->max_per_pipe_ib[i] = 0;
> -		}
> +		perf->bw_ctl = 0;
> +		perf->max_per_pipe_ib = 0;
>  		perf->core_clk_rate = 0;
>  	} else if (kms->perf.perf_tune.mode == DPU_PERF_MODE_FIXED) {
> -		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -			perf->bw_ctl[i] = kms->perf.fix_core_ab_vote;
> -			perf->max_per_pipe_ib[i] = kms->perf.fix_core_ib_vote;
> -		}
> +		perf->bw_ctl = kms->perf.fix_core_ab_vote;
> +		perf->max_per_pipe_ib = kms->perf.fix_core_ib_vote;
>  		perf->core_clk_rate = kms->perf.fix_core_clk_rate;
>  	}
> 
>  	DPU_DEBUG(
> -		"crtc=%d clk_rate=%llu core_ib=%llu core_ab=%llu llcc_ib=%llu
> llcc_ab=%llu mem_ib=%llu mem_ab=%llu\n",
> +		"crtc=%d clk_rate=%llu core_ib=%llu core_ab=%llu\n",
>  			crtc->base.id, perf->core_clk_rate,
> -			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_MNOC],
> -			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MNOC],
> -			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_LLCC],
> -			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_LLCC],
> -			perf->max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_EBI],
> -			perf->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_EBI]);
> +			perf->max_per_pipe_ib, perf->bw_ctl);
>  }
> 
>  int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
> @@ -142,7 +130,6 @@ int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
>  	struct dpu_crtc_state *dpu_cstate;
>  	struct drm_crtc *tmp_crtc;
>  	struct dpu_kms *kms;
> -	int i;
> 
>  	if (!crtc || !state) {
>  		DPU_ERROR("invalid crtc\n");
> @@ -164,31 +151,28 @@ int dpu_core_perf_crtc_check(struct drm_crtc 
> *crtc,
>  	/* obtain new values */
>  	_dpu_core_perf_calc_crtc(kms, crtc, state, &dpu_cstate->new_perf);
> 
> -	for (i = DPU_POWER_HANDLE_DBUS_ID_MNOC;
> -			i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -		bw_sum_of_intfs = dpu_cstate->new_perf.bw_ctl[i];
> -		curr_client_type = dpu_crtc_get_client_type(crtc);
> +	bw_sum_of_intfs = dpu_cstate->new_perf.bw_ctl;
> +	curr_client_type = dpu_crtc_get_client_type(crtc);
> 
> -		drm_for_each_crtc(tmp_crtc, crtc->dev) {
> -			if (_dpu_core_perf_crtc_is_power_on(tmp_crtc) &&
> -			    (dpu_crtc_get_client_type(tmp_crtc) ==
> -					    curr_client_type) &&
> -			    (tmp_crtc != crtc)) {
> -				struct dpu_crtc_state *tmp_cstate =
> -					to_dpu_crtc_state(tmp_crtc->state);
> -
> -				DPU_DEBUG("crtc:%d bw:%llu ctrl:%d\n",
> -					tmp_crtc->base.id,
> -					tmp_cstate->new_perf.bw_ctl[i],
> -					tmp_cstate->bw_control);
> -				/*
> -				 * For bw check only use the bw if the
> -				 * atomic property has been already set
> -				 */
> -				if (tmp_cstate->bw_control)
> -					bw_sum_of_intfs +=
> -						tmp_cstate->new_perf.bw_ctl[i];
> -			}
> +	drm_for_each_crtc(tmp_crtc, crtc->dev) {
> +		if (_dpu_core_perf_crtc_is_power_on(tmp_crtc) &&
> +		    (dpu_crtc_get_client_type(tmp_crtc) ==
> +				    curr_client_type) &&
> +		    (tmp_crtc != crtc)) {
> +			struct dpu_crtc_state *tmp_cstate =
> +				to_dpu_crtc_state(tmp_crtc->state);
> +
> +			DPU_DEBUG("crtc:%d bw:%llu ctrl:%d\n",
> +				tmp_crtc->base.id,
> +				tmp_cstate->new_perf.bw_ctl,
> +				tmp_cstate->bw_control);
> +			/*
> +			 * For bw check only use the bw if the
> +			 * atomic property has been already set
> +			 */
> +			if (tmp_cstate->bw_control)
> +				bw_sum_of_intfs +=
> +					tmp_cstate->new_perf.bw_ctl;
>  		}
> 
>  		/* convert bandwidth to kb */
> @@ -219,9 +203,9 @@ int dpu_core_perf_crtc_check(struct drm_crtc *crtc,
>  }
> 
>  static int _dpu_core_perf_crtc_update_bus(struct dpu_kms *kms,
> -		struct drm_crtc *crtc, u32 bus_id)
> +		struct drm_crtc *crtc)
>  {
> -	struct dpu_core_perf_params perf = { { 0 } };
> +	struct dpu_core_perf_params perf = { 0 };
>  	enum dpu_crtc_client_type curr_client_type
>  					= dpu_crtc_get_client_type(crtc);
>  	struct drm_crtc *tmp_crtc;
> @@ -234,13 +218,12 @@ static int _dpu_core_perf_crtc_update_bus(struct
> dpu_kms *kms,
>  				dpu_crtc_get_client_type(tmp_crtc)) {
>  			dpu_cstate = to_dpu_crtc_state(tmp_crtc->state);
> 
> -			perf.max_per_pipe_ib[bus_id] =
> -				max(perf.max_per_pipe_ib[bus_id],
> -				dpu_cstate->new_perf.max_per_pipe_ib[bus_id]);
> +			perf.max_per_pipe_ib =
> +				max(perf.max_per_pipe_ib,
> +				dpu_cstate->new_perf.max_per_pipe_ib);
> 
> -			DPU_DEBUG("crtc=%d bus_id=%d bw=%llu\n",
> -				tmp_crtc->base.id, bus_id,
> -				dpu_cstate->new_perf.bw_ctl[bus_id]);
> +			DPU_DEBUG("crtc=%d bw=%llu\n",
> +				tmp_crtc->base.id, dpu_cstate->new_perf.bw_ctl);
>  		}
>  	}
>  	return ret;
> @@ -260,7 +243,6 @@ void dpu_core_perf_crtc_release_bw(struct drm_crtc 
> *crtc)
>  	struct dpu_crtc *dpu_crtc;
>  	struct dpu_crtc_state *dpu_cstate;
>  	struct dpu_kms *kms;
> -	int i;
> 
>  	if (!crtc) {
>  		DPU_ERROR("invalid crtc\n");
> @@ -296,10 +278,8 @@ void dpu_core_perf_crtc_release_bw(struct drm_crtc 
> *crtc)
>  	if (kms->perf.enable_bw_release) {
>  		trace_dpu_cmd_release_bw(crtc->base.id);
>  		DPU_DEBUG("Release BW crtc=%d\n", crtc->base.id);
> -		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -			dpu_crtc->cur_perf.bw_ctl[i] = 0;
> -			_dpu_core_perf_crtc_update_bus(kms, crtc, i);
> -		}
> +		dpu_crtc->cur_perf.bw_ctl = 0;
> +		_dpu_core_perf_crtc_update_bus(kms, crtc);
>  	}
>  }
> 
> @@ -342,11 +322,10 @@ int dpu_core_perf_crtc_update(struct drm_crtc 
> *crtc,
>  		int params_changed, bool stop_req)
>  {
>  	struct dpu_core_perf_params *new, *old;
> -	int update_bus = 0, update_clk = 0;
> +	bool update_bus = false, update_clk = false;
>  	u64 clk_rate = 0;
>  	struct dpu_crtc *dpu_crtc;
>  	struct dpu_crtc_state *dpu_cstate;
> -	int i;
>  	struct msm_drm_private *priv;
>  	struct dpu_kms *kms;
>  	int ret;
> @@ -373,7 +352,6 @@ int dpu_core_perf_crtc_update(struct drm_crtc 
> *crtc,
>  	new = &dpu_cstate->new_perf;
> 
>  	if (_dpu_core_perf_crtc_is_power_on(crtc) && !stop_req) {
> -		for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
>  			/*
>  			 * cases for bus bandwidth update.
>  			 * 1. new bandwidth vote - "ab or ib vote" is higher
> @@ -381,23 +359,22 @@ int dpu_core_perf_crtc_update(struct drm_crtc 
> *crtc,
>  			 * 2. new bandwidth vote - "ab or ib vote" is lower
>  			 *    than current vote at end of commit or stop.
>  			 */
> -			if ((params_changed && ((new->bw_ctl[i] >
> -						old->bw_ctl[i]) ||
> -				  (new->max_per_pipe_ib[i] >
> -						old->max_per_pipe_ib[i]))) ||
> -			    (!params_changed && ((new->bw_ctl[i] <
> -						old->bw_ctl[i]) ||
> -				  (new->max_per_pipe_ib[i] <
> -						old->max_per_pipe_ib[i])))) {
> +			if ((params_changed && ((new->bw_ctl >
> +						old->bw_ctl) ||
> +				  (new->max_per_pipe_ib >
> +						old->max_per_pipe_ib))) ||
> +			    (!params_changed && ((new->bw_ctl <
> +						old->bw_ctl) ||
> +				  (new->max_per_pipe_ib <
> +						old->max_per_pipe_ib)))) {
>  				DPU_DEBUG(
>  					"crtc=%d p=%d new_bw=%llu,old_bw=%llu\n",
>  					crtc->base.id, params_changed,
> -					new->bw_ctl[i], old->bw_ctl[i]);
> -				old->bw_ctl[i] = new->bw_ctl[i];
> -				old->max_per_pipe_ib[i] =
> -						new->max_per_pipe_ib[i];
> -				update_bus |= BIT(i);
> -			}
> +					new->bw_ctl, old->bw_ctl);
> +				old->bw_ctl = new->bw_ctl;
> +				old->max_per_pipe_ib =
> +						new->max_per_pipe_ib;
> +				update_bus = true;
>  		}
> 
>  		if ((params_changed &&
> @@ -405,30 +382,26 @@ int dpu_core_perf_crtc_update(struct drm_crtc 
> *crtc,
>  				(!params_changed &&
>  				(new->core_clk_rate < old->core_clk_rate))) {
>  			old->core_clk_rate = new->core_clk_rate;
> -			update_clk = 1;
> +			update_clk = true;
>  		}
>  	} else {
>  		DPU_DEBUG("crtc=%d disable\n", crtc->base.id);
>  		memset(old, 0, sizeof(*old));
>  		memset(new, 0, sizeof(*new));
> -		update_bus = ~0;
> -		update_clk = 1;
> +		update_bus = true;
> +		update_clk = true;
>  	}
> +
>  	trace_dpu_perf_crtc_update(crtc->base.id,
> -				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MNOC],
> -				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_LLCC],
> -				new->bw_ctl[DPU_POWER_HANDLE_DBUS_ID_EBI],
> -				new->core_clk_rate, stop_req,
> -				update_bus, update_clk);
> -
> -	for (i = 0; i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
> -		if (update_bus & BIT(i)) {
> -			ret = _dpu_core_perf_crtc_update_bus(kms, crtc, i);
> -			if (ret) {
> -				DPU_ERROR("crtc-%d: failed to update bw vote for bus-%d\n",
> -					  crtc->base.id, i);
> -				return ret;
> -			}
> +				new->bw_ctl, new->core_clk_rate,
> +				stop_req, update_bus, update_clk);
> +
> +	if (update_bus) {
> +		ret = _dpu_core_perf_crtc_update_bus(kms, crtc);
> +		if (ret) {
> +			DPU_ERROR("crtc-%d: failed to update bus bw vote\n",
> +				  crtc->base.id);
> +			return ret;
>  		}
>  	}
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
> index fbcbe0c7527a..0fb276929dc5 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.h
> @@ -30,8 +30,8 @@
>   * @core_clk_rate: core clock rate request
>   */
>  struct dpu_core_perf_params {
> -	u64 max_per_pipe_ib[DPU_POWER_HANDLE_DBUS_ID_MAX];
> -	u64 bw_ctl[DPU_POWER_HANDLE_DBUS_ID_MAX];
> +	u64 max_per_pipe_ib;
> +	u64 bw_ctl;
>  	u64 core_clk_rate;
>  };
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> index d4530d60767b..4ecb6f96e6ba 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c
> @@ -1450,7 +1450,6 @@ static int dpu_crtc_debugfs_state_show(struct
> seq_file *s, void *v)
>  {
>  	struct drm_crtc *crtc = (struct drm_crtc *) s->private;
>  	struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc);
> -	int i;
> 
>  	seq_printf(s, "client type: %d\n", dpu_crtc_get_client_type(crtc));
>  	seq_printf(s, "intf_mode: %d\n", dpu_crtc_get_intf_mode(crtc));

Missed uploading the rest of the clean up code in this function.
Will update in the v2 patch.

> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
> index fc14116789f2..d58d01544731 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.c
> @@ -24,20 +24,6 @@
>  #include "dpu_power_handle.h"
>  #include "dpu_trace.h"
> 
> -static const char *data_bus_name[DPU_POWER_HANDLE_DBUS_ID_MAX] = {
> -	[DPU_POWER_HANDLE_DBUS_ID_MNOC] = "qcom,dpu-data-bus",
> -	[DPU_POWER_HANDLE_DBUS_ID_LLCC] = "qcom,dpu-llcc-bus",
> -	[DPU_POWER_HANDLE_DBUS_ID_EBI] = "qcom,dpu-ebi-bus",
> -};
> -
> -const char *dpu_power_handle_get_dbus_name(u32 bus_id)
> -{
> -	if (bus_id < DPU_POWER_HANDLE_DBUS_ID_MAX)
> -		return data_bus_name[bus_id];
> -
> -	return NULL;
> -}
> -
>  static void dpu_power_event_trigger_locked(struct dpu_power_handle 
> *phandle,
>  		u32 event_type)
>  {
> @@ -66,7 +52,6 @@ struct dpu_power_client *dpu_power_client_create(
> 
>  	mutex_lock(&phandle->phandle_lock);
>  	strlcpy(client->name, client_name, MAX_CLIENT_NAME_LEN);
> -	client->usecase_ndx = VOTE_INDEX_DISABLE;
>  	client->id = id;
>  	client->active = true;
>  	pr_debug("client %s created:%pK id :%d\n", client_name,
> @@ -143,8 +128,6 @@ int dpu_power_resource_enable(struct
> dpu_power_handle *phandle,
>  	struct dpu_power_client *pclient, bool enable)
>  {
>  	bool changed = false;
> -	u32 max_usecase_ndx = VOTE_INDEX_DISABLE, prev_usecase_ndx;
> -	struct dpu_power_client *client;
>  	u32 event_type;
> 
>  	if (!phandle || !pclient) {
> @@ -153,31 +136,19 @@ int dpu_power_resource_enable(struct
> dpu_power_handle *phandle,
>  	}
> 
>  	mutex_lock(&phandle->phandle_lock);
> -	if (enable)
> +	if (enable) {
>  		pclient->refcount++;
> -	else if (pclient->refcount)
> +		if (pclient->refcount == 1)
> +			changed = true;
> +	} else if (pclient->refcount) {
>  		pclient->refcount--;
> -
> -	if (pclient->refcount)
> -		pclient->usecase_ndx = VOTE_INDEX_LOW;
> -	else
> -		pclient->usecase_ndx = VOTE_INDEX_DISABLE;
> -
> -	list_for_each_entry(client, &phandle->power_client_clist, list) {
> -		if (client->usecase_ndx < VOTE_INDEX_MAX &&
> -		    client->usecase_ndx > max_usecase_ndx)
> -			max_usecase_ndx = client->usecase_ndx;
> -	}
> -
> -	if (phandle->current_usecase_ndx != max_usecase_ndx) {
> -		changed = true;
> -		prev_usecase_ndx = phandle->current_usecase_ndx;
> -		phandle->current_usecase_ndx = max_usecase_ndx;
> +		if (!pclient->refcount)
> +			changed = true;
>  	}
> 
> -	pr_debug("%pS: changed=%d current idx=%d request client %s id:%u
> enable:%d refcount:%d\n",
> -		__builtin_return_address(0), changed, max_usecase_ndx,
> -		pclient->name, pclient->id, enable, pclient->refcount);
> +	pr_debug("%pS:changed=%d client %s id:%u enable:%d refcount:%d\n",
> +		__builtin_return_address(0), changed, pclient->name,
> +		pclient->id, enable, pclient->refcount);
> 
>  	if (!changed)
>  		goto end;
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
> index a65b7a297f21..b1a5ae4d6f4e 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_power_handle.h
> @@ -16,76 +16,28 @@
> 
>  #define MAX_CLIENT_NAME_LEN 128
> 
> -#define DPU_POWER_HANDLE_ENABLE_BUS_AB_QUOTA	0
> -#define DPU_POWER_HANDLE_DISABLE_BUS_AB_QUOTA	0
> -#define DPU_POWER_HANDLE_ENABLE_BUS_IB_QUOTA	1600000000
> -#define DPU_POWER_HANDLE_DISABLE_BUS_IB_QUOTA	0
> -
>  #include "dpu_io_util.h"
> 
>  /* events will be triggered on power handler enable/disable */
>  #define DPU_POWER_EVENT_DISABLE	BIT(0)
>  #define DPU_POWER_EVENT_ENABLE	BIT(1)
> 
> -/**
> - * mdss_bus_vote_type: register bus vote type
> - * VOTE_INDEX_DISABLE: removes the client vote
> - * VOTE_INDEX_LOW: keeps the lowest vote for register bus
> - * VOTE_INDEX_MAX: invalid
> - */
> -enum mdss_bus_vote_type {
> -	VOTE_INDEX_DISABLE,
> -	VOTE_INDEX_LOW,
> -	VOTE_INDEX_MAX,
> -};
> -
> -/**
> - * enum dpu_power_handle_data_bus_client - type of axi bus clients
> - * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_RT: core real-time bus client
> - * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_NRT: core non-real-time bus 
> client
> - * @DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX: maximum number of bus client 
> type
> - */
> -enum dpu_power_handle_data_bus_client {
> -	DPU_POWER_HANDLE_DATA_BUS_CLIENT_RT,
> -	DPU_POWER_HANDLE_DATA_BUS_CLIENT_NRT,
> -	DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX
> -};
> -
> -/**
> - * enum DPU_POWER_HANDLE_DBUS_ID - data bus identifier
> - * @DPU_POWER_HANDLE_DBUS_ID_MNOC: DPU/MNOC data bus
> - * @DPU_POWER_HANDLE_DBUS_ID_LLCC: MNOC/LLCC data bus
> - * @DPU_POWER_HANDLE_DBUS_ID_EBI: LLCC/EBI data bus
> - */
> -enum DPU_POWER_HANDLE_DBUS_ID {
> -	DPU_POWER_HANDLE_DBUS_ID_MNOC,
> -	DPU_POWER_HANDLE_DBUS_ID_LLCC,
> -	DPU_POWER_HANDLE_DBUS_ID_EBI,
> -	DPU_POWER_HANDLE_DBUS_ID_MAX,
> -};
> -
>  /**
>   * struct dpu_power_client: stores the power client for dpu driver
>   * @name:	name of the client
> - * @usecase_ndx: current regs bus vote type
>   * @refcount:	current refcount if multiple modules are using same
>   *              same client for enable/disable. Power module will
>   *              aggregate the refcount and vote accordingly for this
>   *              client.
>   * @id:		assigned during create. helps for debugging.
>   * @list:	list to attach power handle master list
> - * @ab:         arbitrated bandwidth for each bus client
> - * @ib:         instantaneous bandwidth for each bus client
>   * @active:	inidcates the state of dpu power handle
>   */
>  struct dpu_power_client {
>  	char name[MAX_CLIENT_NAME_LEN];
> -	short usecase_ndx;
>  	short refcount;
>  	u32 id;
>  	struct list_head list;
> -	u64 ab[DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX];
> -	u64 ib[DPU_POWER_HANDLE_DATA_BUS_CLIENT_MAX];
>  	bool active;
>  };
> 
> @@ -112,14 +64,12 @@ struct dpu_power_event {
>   * @client_clist: master list to store all clients
>   * @phandle_lock: lock to synchronize the enable/disable
>   * @dev: pointer to device structure
> - * @usecase_ndx: current usecase index
>   * @event_list: current power handle event list
>   */
>  struct dpu_power_handle {
>  	struct list_head power_client_clist;
>  	struct mutex phandle_lock;
>  	struct device *dev;
> -	u32 current_usecase_ndx;
>  	struct list_head event_list;
>  };
> 
> @@ -172,17 +122,6 @@ void dpu_power_client_destroy(struct
> dpu_power_handle *phandle,
>  int dpu_power_resource_enable(struct dpu_power_handle *pdata,
>  	struct dpu_power_client *pclient, bool enable);
> 
> -/**
> - * dpu_power_data_bus_bandwidth_ctrl() - control data bus bandwidth 
> enable
> - * @phandle:  power handle containing the resources
> - * @client: client information to bandwidth control
> - * @enable: true to enable bandwidth for data base
> - *
> - * Return: none
> - */
> -void dpu_power_data_bus_bandwidth_ctrl(struct dpu_power_handle 
> *phandle,
> -		struct dpu_power_client *pclient, int enable);
> -
>  /**
>   * dpu_power_handle_register_event - register a callback function for 
> an event.
>   *	Clients can register for multiple events with a single register.
> @@ -207,11 +146,4 @@ struct dpu_power_event 
> *dpu_power_handle_register_event(
>  void dpu_power_handle_unregister_event(struct dpu_power_handle 
> *phandle,
>  		struct dpu_power_event *event);
> 
> -/**
> - * dpu_power_handle_get_dbus_name - get name of given data bus 
> identifier
> - * @bus_id:	data bus identifier
> - * Return:	Pointer to name string if success; NULL otherwise
> - */
> -const char *dpu_power_handle_get_dbus_name(u32 bus_id);
> -
>  #endif /* _DPU_POWER_HANDLE_H_ */
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
> b/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
> index 636b31b0d311..72a32e9b5ca5 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_trace.h
> @@ -167,16 +167,13 @@ TRACE_EVENT(dpu_trace_counter,
>  )
> 
>  TRACE_EVENT(dpu_perf_crtc_update,
> -	TP_PROTO(u32 crtc, u64 bw_ctl_mnoc, u64 bw_ctl_llcc,
> -			u64 bw_ctl_ebi, u32 core_clk_rate,
> -			bool stop_req, u32 update_bus, u32 update_clk),
> -	TP_ARGS(crtc, bw_ctl_mnoc, bw_ctl_llcc, bw_ctl_ebi, core_clk_rate,
> +	TP_PROTO(u32 crtc, u64 bw_ctl, u32 core_clk_rate,
> +			bool stop_req, bool update_bus, bool update_clk),
> +	TP_ARGS(crtc, bw_ctl, core_clk_rate,
>  		stop_req, update_bus, update_clk),
>  	TP_STRUCT__entry(
>  			__field(u32, crtc)
> -			__field(u64, bw_ctl_mnoc)
> -			__field(u64, bw_ctl_llcc)
> -			__field(u64, bw_ctl_ebi)
> +			__field(u64, bw_ctl)
>  			__field(u32, core_clk_rate)
>  			__field(bool, stop_req)
>  			__field(u32, update_bus)
> @@ -184,20 +181,16 @@ TRACE_EVENT(dpu_perf_crtc_update,
>  	),
>  	TP_fast_assign(
>  			__entry->crtc = crtc;
> -			__entry->bw_ctl_mnoc = bw_ctl_mnoc;
> -			__entry->bw_ctl_llcc = bw_ctl_llcc;
> -			__entry->bw_ctl_ebi = bw_ctl_ebi;
> +			__entry->bw_ctl = bw_ctl;
>  			__entry->core_clk_rate = core_clk_rate;
>  			__entry->stop_req = stop_req;
>  			__entry->update_bus = update_bus;
>  			__entry->update_clk = update_clk;
>  	),
>  	 TP_printk(
> -		"crtc=%d bw_mnoc=%llu bw_llcc=%llu bw_ebi=%llu clk_rate=%u
> stop_req=%d u_bus=%d u_clk=%d",
> +		"crtc=%d bw_ctl=%llu clk_rate=%u stop_req=%d u_bus=%d u_clk=%d",
>  			__entry->crtc,
> -			__entry->bw_ctl_mnoc,
> -			__entry->bw_ctl_llcc,
> -			__entry->bw_ctl_ebi,
> +			__entry->bw_ctl,
>  			__entry->core_clk_rate,
>  			__entry->stop_req,
>  			__entry->update_bus,
_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno

Re: [PATCH 1/3] drm/msm/dpu: clean up references of DPU custom bus scaling

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 4621 bytes --]

Hi Sravanthi,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on robclark/msm-next]
[also build test ERROR on next-20181009]
[cannot apply to v4.19-rc7]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Sravanthi-Kollukuduru/Use-interconnect-API-in-MDSS-on-SDM845/20181008-203309
base:   git://people.freedesktop.org/~robclark/linux msm-next
config: arm-multi_v7_defconfig (attached as .config)
compiler: arm-linux-gnueabi-gcc (Debian 7.2.0-11) 7.2.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # save the attached .config to linux build tree
        GCC_VERSION=7.2.0 make.cross ARCH=arm 

All errors (new ones prefixed by >>):

   drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c: In function 'dpu_crtc_debugfs_state_show':
>> drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c:1458:7: error: 'i' undeclared (first use in this function)
     for (i = DPU_POWER_HANDLE_DBUS_ID_MNOC;
          ^
   drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c:1458:7: note: each undeclared identifier is reported only once for each function it appears in
>> drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c:1458:11: error: 'DPU_POWER_HANDLE_DBUS_ID_MNOC' undeclared (first use in this function); did you mean '_DPU_POWER_HANDLE_H_'?
     for (i = DPU_POWER_HANDLE_DBUS_ID_MNOC;
              ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
              _DPU_POWER_HANDLE_H_
>> drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c:1459:8: error: 'DPU_POWER_HANDLE_DBUS_ID_MAX' undeclared (first use in this function); did you mean 'DPU_POWER_HANDLE_DBUS_ID_MNOC'?
       i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
           DPU_POWER_HANDLE_DBUS_ID_MNOC
>> drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c:1461:5: error: implicit declaration of function 'dpu_power_handle_get_dbus_name'; did you mean 'dpu_power_handle_register_event'? [-Werror=implicit-function-declaration]
        dpu_power_handle_get_dbus_name(i),
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        dpu_power_handle_register_event
   cc1: some warnings being treated as errors

vim +1458 drivers/gpu//drm/msm/disp/dpu1/dpu_crtc.c

25fdd593 Jeykumar Sankaran 2018-06-27  1448  
25fdd593 Jeykumar Sankaran 2018-06-27  1449  static int dpu_crtc_debugfs_state_show(struct seq_file *s, void *v)
25fdd593 Jeykumar Sankaran 2018-06-27  1450  {
25fdd593 Jeykumar Sankaran 2018-06-27  1451  	struct drm_crtc *crtc = (struct drm_crtc *) s->private;
25fdd593 Jeykumar Sankaran 2018-06-27  1452  	struct dpu_crtc *dpu_crtc = to_dpu_crtc(crtc);
25fdd593 Jeykumar Sankaran 2018-06-27  1453  
25fdd593 Jeykumar Sankaran 2018-06-27  1454  	seq_printf(s, "client type: %d\n", dpu_crtc_get_client_type(crtc));
25fdd593 Jeykumar Sankaran 2018-06-27  1455  	seq_printf(s, "intf_mode: %d\n", dpu_crtc_get_intf_mode(crtc));
25fdd593 Jeykumar Sankaran 2018-06-27  1456  	seq_printf(s, "core_clk_rate: %llu\n",
25fdd593 Jeykumar Sankaran 2018-06-27  1457  			dpu_crtc->cur_perf.core_clk_rate);
25fdd593 Jeykumar Sankaran 2018-06-27 @1458  	for (i = DPU_POWER_HANDLE_DBUS_ID_MNOC;
25fdd593 Jeykumar Sankaran 2018-06-27 @1459  			i < DPU_POWER_HANDLE_DBUS_ID_MAX; i++) {
25fdd593 Jeykumar Sankaran 2018-06-27  1460  		seq_printf(s, "bw_ctl[%s]: %llu\n",
25fdd593 Jeykumar Sankaran 2018-06-27 @1461  				dpu_power_handle_get_dbus_name(i),
25fdd593 Jeykumar Sankaran 2018-06-27  1462  				dpu_crtc->cur_perf.bw_ctl[i]);
25fdd593 Jeykumar Sankaran 2018-06-27  1463  		seq_printf(s, "max_per_pipe_ib[%s]: %llu\n",
25fdd593 Jeykumar Sankaran 2018-06-27  1464  				dpu_power_handle_get_dbus_name(i),
25fdd593 Jeykumar Sankaran 2018-06-27  1465  				dpu_crtc->cur_perf.max_per_pipe_ib[i]);
25fdd593 Jeykumar Sankaran 2018-06-27  1466  	}
25fdd593 Jeykumar Sankaran 2018-06-27  1467  
25fdd593 Jeykumar Sankaran 2018-06-27  1468  	return 0;
25fdd593 Jeykumar Sankaran 2018-06-27  1469  }
25fdd593 Jeykumar Sankaran 2018-06-27  1470  DEFINE_DPU_DEBUGFS_SEQ_FOPS(dpu_crtc_debugfs_state);
25fdd593 Jeykumar Sankaran 2018-06-27  1471  

:::::: The code at line 1458 was first introduced by commit
:::::: 25fdd5933e4c0f5fe2ea5cd59994f8ac5fbe90ef drm/msm: Add SDM845 DPU support

:::::: TO: Jeykumar Sankaran <jsanka-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
:::::: CC: Sean Paul <seanpaul-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 44419 bytes --]

[-- Attachment #3: Type: text/plain, Size: 160 bytes --]

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno