[PATCH v8 0/9] Goodix touchscreen enhancements

[PATCH v8 0/9] Goodix touchscreen enhancements

[Irina Tirdea]

Add several enhancements to the Goodix touchscreen driver.

The new functionality is only available for devices that
declare named gpio pins for interrupt and reset in their
ACPI/DT configuration.

Thanks,
Irina

Changes in v8:
 - only allow new functionality for devices that declare named
gpios (using _DSD properties in ACPI or named DT properties)

Changes in v7:
 - add dmi quirk to skip gpio pins setup and functionality that
depends on them for Onda v975w, WinBook TW100 and WinBook TW700.
 - add support for named gpio pins
 - rework the runtime pm patch to fix a couple of issues
 - sort includes using inverse Xmas tree ordering

Changes in v6:
 - skip runtime power manangent calls in open/close if the device
ACPI/DT configuration does not declare interrupt and reset gpio pins.
 - reset the device before starting i2c communication
 - add Bastien's ack to the first 2 patches

Changes in v5:
 - add some more style cleanup (reorder includes, use error instead
of ret for return values)
 - add runtime power management patch

Changes in v4:
 - use dmi quirk to determine the order of irq and reset pins
 - use actual config length depending on device
 - add sysfs interface to dump config
 - initialize esd timeout from ACPI/DT properly

Changes in v3:
 - dropped the first 3 patches that got merged
 - handle -EPROBE_DEFER and -ENOENT for gpio pins
 - skip functionality depending on the gpio pins if the pins are not
properly initialized from ACPI/DT (reset, write config, power management,
ESD)
 - dropped #ifdef CONFIG_PM_SLEEP and annotated with __maybe_unused instead
 - use sysfs property to set ESD timeout instead of ACPI/DT property
 - use request_firmware_nowait to read configuration firmware and use
defaults if firmware is not found
 - use ACPI IDs to determine the order of the GPIO pins in the ACPI tables
(interrupt pin first or reset pin first)

Changes in v2:
 - use request_firmware instead of ACPI/DT property for config
 - dropped "input: goodix: add ACPI IDs for GT911 and GT9271" patch
 - add ACPI DSDT excerpt in commit message where necessary
 - add comments for suspend/resume sleep values
 - dropped the checkpatch fixes that did not make sense
 - added Bastien's ack to the first patch

Irina Tirdea (9):
  Input: goodix - use actual config length for each device type
  Input: goodix - reset device at init
  Input: goodix - write configuration data to device
  Input: goodix - add power management support
  Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
  Input: goodix - add support for ESD
  Input: goodix - add sysfs interface to dump config
  Input: goodix - add runtime power management support
  Input: goodix - sort includes using inverse Xmas tree order

 .../bindings/input/touchscreen/goodix.txt          |  11 +
 drivers/input/touchscreen/goodix.c                 | 766 +++++++++++++++++++--
 2 files changed, 732 insertions(+), 45 deletions(-)

-- 
1.9.1

[PATCH v8 1/9] Input: goodix - use actual config length for each device type

[Irina Tirdea]

Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.

Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
---
 drivers/input/touchscreen/goodix.c | 25 +++++++++++++++++++++++--
 1 file changed, 23 insertions(+), 2 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 4d113c9..56d0330 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -36,6 +36,7 @@ struct goodix_ts_data {
 	unsigned int max_touch_num;
 	unsigned int int_trigger_type;
 	bool rotated_screen;
+	int cfg_len;
 };
 
 #define GOODIX_MAX_HEIGHT		4096
@@ -45,6 +46,8 @@ struct goodix_ts_data {
 #define GOODIX_MAX_CONTACTS		10
 
 #define GOODIX_CONFIG_MAX_LENGTH	240
+#define GOODIX_CONFIG_911_LENGTH	186
+#define GOODIX_CONFIG_967_LENGTH	228
 
 /* Register defines */
 #define GOODIX_READ_COOR_ADDR		0x814E
@@ -115,6 +118,23 @@ static int goodix_i2c_read(struct i2c_client *client,
 	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
 }
 
+static int goodix_get_cfg_len(u16 id)
+{
+	switch (id) {
+	case 911:
+	case 9271:
+	case 9110:
+	case 927:
+	case 928:
+		return GOODIX_CONFIG_911_LENGTH;
+	case 912:
+	case 967:
+		return GOODIX_CONFIG_967_LENGTH;
+	default:
+		return GOODIX_CONFIG_MAX_LENGTH;
+	}
+}
+
 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
 {
 	int touch_num;
@@ -230,8 +250,7 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 	int error;
 
 	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
-				config,
-				GOODIX_CONFIG_MAX_LENGTH);
+				config, ts->cfg_len);
 	if (error) {
 		dev_warn(&ts->client->dev,
 			 "Error reading config (%d), using defaults\n",
@@ -398,6 +417,8 @@ static int goodix_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	ts->cfg_len = goodix_get_cfg_len(id_info);
+
 	goodix_read_config(ts);
 
 	error = goodix_request_input_dev(ts, version_info, id_info);
-- 
1.9.1

[PATCH v8 2/9] Input: goodix - reset device at init

[Irina Tirdea]

After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.

This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).

For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.

For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpio" property and the reset pin configuration is
read from the "reset-gpio" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).

For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
    Name (_HID, "GDIX1001")
    ...

    Method (_CRS, 0, Serialized)
    {
        Name (RBUF, ResourceTemplate ()
        {
            I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
                AddressingMode7Bit, "\\I2C0",
                0x00, ResourceConsumer, ,
                )

            GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
                "\\I2C0", 0x00, ResourceConsumer, ,
                 )
                 {   // Pin list
                     0
                 }

            GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
                IoRestrictionOutputOnly, "\\I2C0", 0x00,
                ResourceConsumer, ,
                )
                {
                     1
                }
        })
        Return (RBUF)
    }

    Name (_DSD,  Package ()
    {
        ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
        Package ()
        {
            Package (2) {"irq-gpio", Package() {^STAC, 0, 0, 0 }},
            Package (2) {"reset-gpio", Package() {^STAC, 1, 0, 0 }},
            ...
        }
    }

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 .../bindings/input/touchscreen/goodix.txt          |   5 +
 drivers/input/touchscreen/goodix.c                 | 101 +++++++++++++++++++++
 2 files changed, 106 insertions(+)

diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 8ba98ee..7137881 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -12,6 +12,8 @@ Required properties:
  - reg			: I2C address of the chip. Should be 0x5d or 0x14
  - interrupt-parent	: Interrupt controller to which the chip is connected
  - interrupts		: Interrupt to which the chip is connected
+ - irq-gpio		: GPIO pin used for IRQ
+ - reset-gpio		: GPIO pin used for reset
 
 Example:
 
@@ -23,6 +25,9 @@ Example:
 			reg = <0x5d>;
 			interrupt-parent = <&gpio>;
 			interrupts = <0 0>;
+
+			irq-gpio = <&gpio1 0 0>;
+			reset-gpio = <&gpio1 1 0>;
 		};
 
 		/* ... */
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 56d0330..87304ac 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -16,6 +16,7 @@
 
 #include <linux/kernel.h>
 #include <linux/dmi.h>
+#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/input/mt.h>
@@ -37,8 +38,13 @@ struct goodix_ts_data {
 	unsigned int int_trigger_type;
 	bool rotated_screen;
 	int cfg_len;
+	struct gpio_desc *gpiod_int;
+	struct gpio_desc *gpiod_rst;
 };
 
+#define GOODIX_GPIO_INT_NAME		"irq"
+#define GOODIX_GPIO_RST_NAME		"reset"
+
 #define GOODIX_MAX_HEIGHT		4096
 #define GOODIX_MAX_WIDTH		4096
 #define GOODIX_INT_TRIGGER		1
@@ -237,6 +243,88 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+	int error;
+
+	error = gpiod_direction_output(ts->gpiod_int, 0);
+	if (error)
+		return error;
+	msleep(50);				/* T5: 50ms */
+
+	return gpiod_direction_input(ts->gpiod_int);
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+	int error;
+
+	/* begin select I2C slave addr */
+	error = gpiod_direction_output(ts->gpiod_rst, 0);
+	if (error)
+		return error;
+	msleep(20);				/* T2: > 10ms */
+	/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+	error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+	if (error)
+		return error;
+	usleep_range(100, 2000);		/* T3: > 100us */
+	error = gpiod_direction_output(ts->gpiod_rst, 1);
+	if (error)
+		return error;
+	usleep_range(6000, 10000);		/* T4: > 5ms */
+	/* end select I2C slave addr */
+	error = gpiod_direction_input(ts->gpiod_rst);
+	if (error)
+		return error;
+	return goodix_int_sync(ts);
+}
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts)
+{
+	int error;
+	struct device *dev;
+	struct gpio_desc *gpiod;
+
+	if (!ts->client)
+		return -EINVAL;
+	dev = &ts->client->dev;
+
+	/* Get the interrupt GPIO pin number */
+	gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_INT_NAME, error);
+		return error;
+	}
+	ts->gpiod_int = gpiod;
+
+	/* Get the reset line GPIO pin number */
+	gpiod = devm_gpiod_get(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_RST_NAME, error);
+		return error;
+	}
+	ts->gpiod_rst = gpiod;
+
+	return 0;
+}
+
 /**
  * goodix_read_config - Read the embedded configuration of the panel
  *
@@ -405,6 +493,19 @@ static int goodix_ts_probe(struct i2c_client *client,
 	ts->client = client;
 	i2c_set_clientdata(client, ts);
 
+	error = goodix_get_gpio_config(ts);
+	if (error == -EPROBE_DEFER)
+		return error;
+
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* reset the controller */
+		error = goodix_reset(ts);
+		if (error) {
+			dev_err(&client->dev, "Controller reset failed.\n");
+			return error;
+		}
+	}
+
 	error = goodix_i2c_test(client);
 	if (error) {
 		dev_err(&client->dev, "I2C communication failure: %d\n", error);
-- 
1.9.1

[PATCH v8 3/9] Input: goodix - write configuration data to device

[Irina Tirdea]

Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).

The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).

Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.

This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 229 +++++++++++++++++++++++++++++++------
 1 file changed, 196 insertions(+), 33 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 87304ac..b4dfe4b 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -16,6 +16,7 @@
 
 #include <linux/kernel.h>
 #include <linux/dmi.h>
+#include <linux/firmware.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
@@ -40,6 +41,9 @@ struct goodix_ts_data {
 	int cfg_len;
 	struct gpio_desc *gpiod_int;
 	struct gpio_desc *gpiod_rst;
+	u16 id;
+	u16 version;
+	char *cfg_name;
 };
 
 #define GOODIX_GPIO_INT_NAME		"irq"
@@ -124,6 +128,39 @@ static int goodix_i2c_read(struct i2c_client *client,
 	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
 }
 
+/**
+ * goodix_i2c_write - write data to a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to write to.
+ * @buf: raw data buffer to write.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
+			    unsigned len)
+{
+	u8 *addr_buf;
+	struct i2c_msg msg;
+	int ret;
+
+	addr_buf = kmalloc(len + 2, GFP_KERNEL);
+	if (!addr_buf)
+		return -ENOMEM;
+
+	addr_buf[0] = reg >> 8;
+	addr_buf[1] = reg & 0xFF;
+	memcpy(&addr_buf[2], buf, len);
+
+	msg.flags = 0;
+	msg.addr = client->addr;
+	msg.buf = addr_buf;
+	msg.len = len + 2;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	kfree(addr_buf);
+	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
+}
+
 static int goodix_get_cfg_len(u16 id)
 {
 	switch (id) {
@@ -243,6 +280,73 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+/**
+ * goodix_check_cfg - Checks if config fw is valid
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: firmware config data
+ */
+static int goodix_check_cfg(struct goodix_ts_data *ts,
+			    const struct firmware *cfg)
+{
+	int i, raw_cfg_len;
+	u8 check_sum = 0;
+
+	if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+		dev_err(&ts->client->dev,
+			"The length of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	raw_cfg_len = cfg->size - 2;
+	for (i = 0; i < raw_cfg_len; i++)
+		check_sum += cfg->data[i];
+	check_sum = (~check_sum) + 1;
+	if (check_sum != cfg->data[raw_cfg_len]) {
+		dev_err(&ts->client->dev,
+			"The checksum of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	if (cfg->data[raw_cfg_len + 1] != 1) {
+		dev_err(&ts->client->dev,
+			"Config fw must have Config_Fresh register set");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_send_cfg - Write fw config to device
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: config firmware to write to device
+ */
+static int goodix_send_cfg(struct goodix_ts_data *ts,
+			   const struct firmware *cfg)
+{
+	int error;
+
+	error = goodix_check_cfg(ts, cfg);
+	if (error)
+		return error;
+
+	error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
+				 cfg->size);
+	if (error) {
+		dev_err(&ts->client->dev, "Failed to write config data: %d",
+			error);
+		return error;
+	}
+	dev_dbg(&ts->client->dev, "Config sent successfully.");
+
+	/* Let the firmware reconfigure itself, so sleep for 10ms */
+	usleep_range(10000, 11000);
+
+	return 0;
+}
+
 static int goodix_int_sync(struct goodix_ts_data *ts)
 {
 	int error;
@@ -371,30 +475,29 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 /**
  * goodix_read_version - Read goodix touchscreen version
  *
- * @client: the i2c client
- * @version: output buffer containing the version on success
- * @id: output buffer containing the id on success
+ * @ts: our goodix_ts_data pointer
  */
-static int goodix_read_version(struct i2c_client *client, u16 *version, u16 *id)
+static int goodix_read_version(struct goodix_ts_data *ts)
 {
 	int error;
 	u8 buf[6];
 	char id_str[5];
 
-	error = goodix_i2c_read(client, GOODIX_REG_ID, buf, sizeof(buf));
+	error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
 	if (error) {
-		dev_err(&client->dev, "read version failed: %d\n", error);
+		dev_err(&ts->client->dev, "read version failed: %d\n", error);
 		return error;
 	}
 
 	memcpy(id_str, buf, 4);
 	id_str[4] = 0;
-	if (kstrtou16(id_str, 10, id))
-		*id = 0x1001;
+	if (kstrtou16(id_str, 10, &ts->id))
+		ts->id = 0x1001;
 
-	*version = get_unaligned_le16(&buf[4]);
+	ts->version = get_unaligned_le16(&buf[4]);
 
-	dev_info(&client->dev, "ID %d, version: %04x\n", *id, *version);
+	dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+		 ts->version);
 
 	return 0;
 }
@@ -428,13 +531,10 @@ static int goodix_i2c_test(struct i2c_client *client)
  * goodix_request_input_dev - Allocate, populate and register the input device
  *
  * @ts: our goodix_ts_data pointer
- * @version: device firmware version
- * @id: device ID
  *
  * Must be called during probe
  */
-static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
-				    u16 id)
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
 {
 	int error;
 
@@ -458,8 +558,8 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	ts->input_dev->phys = "input/ts";
 	ts->input_dev->id.bustype = BUS_I2C;
 	ts->input_dev->id.vendor = 0x0416;
-	ts->input_dev->id.product = id;
-	ts->input_dev->id.version = version;
+	ts->input_dev->id.product = ts->id;
+	ts->input_dev->id.version = ts->version;
 
 	error = input_register_device(ts->input_dev);
 	if (error) {
@@ -471,13 +571,70 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	return 0;
 }
 
+/**
+ * goodix_configure_dev - Finish device initialization
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called from probe to finish initialization of the device.
+ * Contains the common initialization code for both devices that
+ * declare gpio pins and devices that do not. It is either called
+ * directly from probe or from request_firmware_wait callback.
+ */
+static int goodix_configure_dev(struct goodix_ts_data *ts)
+{
+	int error;
+	unsigned long irq_flags;
+
+	goodix_read_config(ts);
+
+	error = goodix_request_input_dev(ts);
+	if (error)
+		return error;
+
+	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+					  NULL, goodix_ts_irq_handler,
+					  irq_flags, ts->client->name, ts);
+	if (error) {
+		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_config_cb - Callback to finish device init
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * request_firmware_wait callback that finishes
+ * initialization of the device.
+ */
+static void goodix_config_cb(const struct firmware *cfg, void *ctx)
+{
+	struct goodix_ts_data *ts = (struct goodix_ts_data *)ctx;
+	int error;
+
+	if (cfg) {
+		/* send device configuration to the firmware */
+		error = goodix_send_cfg(ts, cfg);
+		if (error)
+			goto err_release_cfg;
+	}
+	goodix_configure_dev(ts);
+
+err_release_cfg:
+	kfree(ts->cfg_name);
+	release_firmware(cfg);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	struct goodix_ts_data *ts;
-	unsigned long irq_flags;
 	int error;
-	u16 version_info, id_info;
 
 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
 
@@ -512,30 +669,36 @@ static int goodix_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
-	error = goodix_read_version(client, &version_info, &id_info);
+	error = goodix_read_version(ts);
 	if (error) {
 		dev_err(&client->dev, "Read version failed.\n");
 		return error;
 	}
 
-	ts->cfg_len = goodix_get_cfg_len(id_info);
+	ts->cfg_len = goodix_get_cfg_len(ts->id);
 
-	goodix_read_config(ts);
-
-	error = goodix_request_input_dev(ts, version_info, id_info);
-	if (error)
-		return error;
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* update device config */
+		ts->cfg_name = kasprintf(GFP_KERNEL, "goodix_%d_cfg.bin",
+					 ts->id);
+		if (!ts->cfg_name)
+			return -ENOMEM;
+
+		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
+						&client->dev, GFP_KERNEL, ts,
+						goodix_config_cb);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to invoke firmware loader: %d\n",
+				error);
+			kfree(ts->cfg_name);
+			return error;
+		}
 
-	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
-	error = devm_request_threaded_irq(&ts->client->dev, client->irq,
-					  NULL, goodix_ts_irq_handler,
-					  irq_flags, client->name, ts);
-	if (error) {
-		dev_err(&client->dev, "request IRQ failed: %d\n", error);
-		return error;
+		return 0;
 	}
 
-	return 0;
+	return goodix_configure_dev(ts);
 }
 
 static const struct i2c_device_id goodix_ts_id[] = {
-- 
1.9.1

[PATCH v8 3/9] Input: goodix - write configuration data to device

[Irina Tirdea]

Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).

The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).

Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.

This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).

Signed-off-by: Octavian Purdila <octavian.purdila-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Irina Tirdea <irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
 drivers/input/touchscreen/goodix.c | 229 +++++++++++++++++++++++++++++++------
 1 file changed, 196 insertions(+), 33 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 87304ac..b4dfe4b 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -16,6 +16,7 @@
 
 #include <linux/kernel.h>
 #include <linux/dmi.h>
+#include <linux/firmware.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
@@ -40,6 +41,9 @@ struct goodix_ts_data {
 	int cfg_len;
 	struct gpio_desc *gpiod_int;
 	struct gpio_desc *gpiod_rst;
+	u16 id;
+	u16 version;
+	char *cfg_name;
 };
 
 #define GOODIX_GPIO_INT_NAME		"irq"
@@ -124,6 +128,39 @@ static int goodix_i2c_read(struct i2c_client *client,
 	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
 }
 
+/**
+ * goodix_i2c_write - write data to a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to write to.
+ * @buf: raw data buffer to write.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
+			    unsigned len)
+{
+	u8 *addr_buf;
+	struct i2c_msg msg;
+	int ret;
+
+	addr_buf = kmalloc(len + 2, GFP_KERNEL);
+	if (!addr_buf)
+		return -ENOMEM;
+
+	addr_buf[0] = reg >> 8;
+	addr_buf[1] = reg & 0xFF;
+	memcpy(&addr_buf[2], buf, len);
+
+	msg.flags = 0;
+	msg.addr = client->addr;
+	msg.buf = addr_buf;
+	msg.len = len + 2;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	kfree(addr_buf);
+	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
+}
+
 static int goodix_get_cfg_len(u16 id)
 {
 	switch (id) {
@@ -243,6 +280,73 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+/**
+ * goodix_check_cfg - Checks if config fw is valid
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: firmware config data
+ */
+static int goodix_check_cfg(struct goodix_ts_data *ts,
+			    const struct firmware *cfg)
+{
+	int i, raw_cfg_len;
+	u8 check_sum = 0;
+
+	if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+		dev_err(&ts->client->dev,
+			"The length of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	raw_cfg_len = cfg->size - 2;
+	for (i = 0; i < raw_cfg_len; i++)
+		check_sum += cfg->data[i];
+	check_sum = (~check_sum) + 1;
+	if (check_sum != cfg->data[raw_cfg_len]) {
+		dev_err(&ts->client->dev,
+			"The checksum of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	if (cfg->data[raw_cfg_len + 1] != 1) {
+		dev_err(&ts->client->dev,
+			"Config fw must have Config_Fresh register set");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_send_cfg - Write fw config to device
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: config firmware to write to device
+ */
+static int goodix_send_cfg(struct goodix_ts_data *ts,
+			   const struct firmware *cfg)
+{
+	int error;
+
+	error = goodix_check_cfg(ts, cfg);
+	if (error)
+		return error;
+
+	error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
+				 cfg->size);
+	if (error) {
+		dev_err(&ts->client->dev, "Failed to write config data: %d",
+			error);
+		return error;
+	}
+	dev_dbg(&ts->client->dev, "Config sent successfully.");
+
+	/* Let the firmware reconfigure itself, so sleep for 10ms */
+	usleep_range(10000, 11000);
+
+	return 0;
+}
+
 static int goodix_int_sync(struct goodix_ts_data *ts)
 {
 	int error;
@@ -371,30 +475,29 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 /**
  * goodix_read_version - Read goodix touchscreen version
  *
- * @client: the i2c client
- * @version: output buffer containing the version on success
- * @id: output buffer containing the id on success
+ * @ts: our goodix_ts_data pointer
  */
-static int goodix_read_version(struct i2c_client *client, u16 *version, u16 *id)
+static int goodix_read_version(struct goodix_ts_data *ts)
 {
 	int error;
 	u8 buf[6];
 	char id_str[5];
 
-	error = goodix_i2c_read(client, GOODIX_REG_ID, buf, sizeof(buf));
+	error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
 	if (error) {
-		dev_err(&client->dev, "read version failed: %d\n", error);
+		dev_err(&ts->client->dev, "read version failed: %d\n", error);
 		return error;
 	}
 
 	memcpy(id_str, buf, 4);
 	id_str[4] = 0;
-	if (kstrtou16(id_str, 10, id))
-		*id = 0x1001;
+	if (kstrtou16(id_str, 10, &ts->id))
+		ts->id = 0x1001;
 
-	*version = get_unaligned_le16(&buf[4]);
+	ts->version = get_unaligned_le16(&buf[4]);
 
-	dev_info(&client->dev, "ID %d, version: %04x\n", *id, *version);
+	dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+		 ts->version);
 
 	return 0;
 }
@@ -428,13 +531,10 @@ static int goodix_i2c_test(struct i2c_client *client)
  * goodix_request_input_dev - Allocate, populate and register the input device
  *
  * @ts: our goodix_ts_data pointer
- * @version: device firmware version
- * @id: device ID
  *
  * Must be called during probe
  */
-static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
-				    u16 id)
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
 {
 	int error;
 
@@ -458,8 +558,8 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	ts->input_dev->phys = "input/ts";
 	ts->input_dev->id.bustype = BUS_I2C;
 	ts->input_dev->id.vendor = 0x0416;
-	ts->input_dev->id.product = id;
-	ts->input_dev->id.version = version;
+	ts->input_dev->id.product = ts->id;
+	ts->input_dev->id.version = ts->version;
 
 	error = input_register_device(ts->input_dev);
 	if (error) {
@@ -471,13 +571,70 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	return 0;
 }
 
+/**
+ * goodix_configure_dev - Finish device initialization
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called from probe to finish initialization of the device.
+ * Contains the common initialization code for both devices that
+ * declare gpio pins and devices that do not. It is either called
+ * directly from probe or from request_firmware_wait callback.
+ */
+static int goodix_configure_dev(struct goodix_ts_data *ts)
+{
+	int error;
+	unsigned long irq_flags;
+
+	goodix_read_config(ts);
+
+	error = goodix_request_input_dev(ts);
+	if (error)
+		return error;
+
+	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+					  NULL, goodix_ts_irq_handler,
+					  irq_flags, ts->client->name, ts);
+	if (error) {
+		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_config_cb - Callback to finish device init
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * request_firmware_wait callback that finishes
+ * initialization of the device.
+ */
+static void goodix_config_cb(const struct firmware *cfg, void *ctx)
+{
+	struct goodix_ts_data *ts = (struct goodix_ts_data *)ctx;
+	int error;
+
+	if (cfg) {
+		/* send device configuration to the firmware */
+		error = goodix_send_cfg(ts, cfg);
+		if (error)
+			goto err_release_cfg;
+	}
+	goodix_configure_dev(ts);
+
+err_release_cfg:
+	kfree(ts->cfg_name);
+	release_firmware(cfg);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	struct goodix_ts_data *ts;
-	unsigned long irq_flags;
 	int error;
-	u16 version_info, id_info;
 
 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
 
@@ -512,30 +669,36 @@ static int goodix_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
-	error = goodix_read_version(client, &version_info, &id_info);
+	error = goodix_read_version(ts);
 	if (error) {
 		dev_err(&client->dev, "Read version failed.\n");
 		return error;
 	}
 
-	ts->cfg_len = goodix_get_cfg_len(id_info);
+	ts->cfg_len = goodix_get_cfg_len(ts->id);
 
-	goodix_read_config(ts);
-
-	error = goodix_request_input_dev(ts, version_info, id_info);
-	if (error)
-		return error;
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* update device config */
+		ts->cfg_name = kasprintf(GFP_KERNEL, "goodix_%d_cfg.bin",
+					 ts->id);
+		if (!ts->cfg_name)
+			return -ENOMEM;
+
+		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
+						&client->dev, GFP_KERNEL, ts,
+						goodix_config_cb);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to invoke firmware loader: %d\n",
+				error);
+			kfree(ts->cfg_name);
+			return error;
+		}
 
-	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
-	error = devm_request_threaded_irq(&ts->client->dev, client->irq,
-					  NULL, goodix_ts_irq_handler,
-					  irq_flags, client->name, ts);
-	if (error) {
-		dev_err(&client->dev, "request IRQ failed: %d\n", error);
-		return error;
+		return 0;
 	}
 
-	return 0;
+	return goodix_configure_dev(ts);
 }
 
 static const struct i2c_device_id goodix_ts_id[] = {
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v8 4/9] Input: goodix - add power management support

[Irina Tirdea]

Implement suspend/resume for goodix driver.

The suspend and resume process uses the gpio pins.
If the device ACPI/DT information does not declare gpio pins,
suspend/resume will not be available for these devices.

This is based on Goodix datasheets for GT911 and GT9271
and on Goodix driver gt9xx.c for Android (publicly available
in Android kernel trees for various devices).

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 94 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 89 insertions(+), 5 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index b4dfe4b..6314a24 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -44,6 +44,7 @@ struct goodix_ts_data {
 	u16 id;
 	u16 version;
 	char *cfg_name;
+	unsigned long irq_flags;
 };
 
 #define GOODIX_GPIO_INT_NAME		"irq"
@@ -60,6 +61,9 @@ struct goodix_ts_data {
 #define GOODIX_CONFIG_967_LENGTH	228
 
 /* Register defines */
+#define GOODIX_REG_COMMAND		0x8040
+#define GOODIX_CMD_SCREEN_OFF		0x05
+
 #define GOODIX_READ_COOR_ADDR		0x814E
 #define GOODIX_REG_CONFIG_DATA		0x8047
 #define GOODIX_REG_ID			0x8140
@@ -161,6 +165,11 @@ static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
 	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
 }
 
+static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
+{
+	return goodix_i2c_write(client, reg, &value, sizeof(value));
+}
+
 static int goodix_get_cfg_len(u16 id)
 {
 	switch (id) {
@@ -280,6 +289,18 @@ static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static void goodix_free_irq(struct goodix_ts_data *ts)
+{
+	devm_free_irq(&ts->client->dev, ts->client->irq, ts);
+}
+
+static int goodix_request_irq(struct goodix_ts_data *ts)
+{
+	return devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+					 NULL, goodix_ts_irq_handler,
+					 ts->irq_flags, ts->client->name, ts);
+}
+
 /**
  * goodix_check_cfg - Checks if config fw is valid
  *
@@ -584,7 +605,6 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts)
 static int goodix_configure_dev(struct goodix_ts_data *ts)
 {
 	int error;
-	unsigned long irq_flags;
 
 	goodix_read_config(ts);
 
@@ -592,10 +612,8 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
 	if (error)
 		return error;
 
-	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
-	error = devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
-					  NULL, goodix_ts_irq_handler,
-					  irq_flags, ts->client->name, ts);
+	ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = goodix_request_irq(ts);
 	if (error) {
 		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
 		return error;
@@ -701,6 +719,71 @@ static int goodix_ts_probe(struct i2c_client *client,
 	return goodix_configure_dev(ts);
 }
 
+static int __maybe_unused goodix_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	/* We need gpio pins to suspend/resume */
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
+	goodix_free_irq(ts);
+	/* Output LOW on the INT pin for 5 ms */
+	error = gpiod_direction_output(ts->gpiod_int, 0);
+	if (error) {
+		goodix_request_irq(ts);
+		return error;
+	}
+	usleep_range(5000, 6000);
+
+	error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND,
+				    GOODIX_CMD_SCREEN_OFF);
+	if (error) {
+		dev_err(&ts->client->dev, "Screen off command failed\n");
+		gpiod_direction_input(ts->gpiod_int);
+		goodix_request_irq(ts);
+		return -EAGAIN;
+	}
+
+	/*
+	 * The datasheet specifies that the interval between sending screen-off
+	 * command and wake-up should be longer than 58 ms. To avoid waking up
+	 * sooner, delay 58ms here.
+	 */
+	msleep(58);
+	return 0;
+}
+
+static int __maybe_unused goodix_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	/*
+	 * Exit sleep mode by outputting HIGH level to INT pin
+	 * for 2ms~5ms.
+	 */
+	error = gpiod_direction_output(ts->gpiod_int, 1);
+	if (error)
+		return error;
+	usleep_range(2000, 5000);
+
+	error = goodix_int_sync(ts);
+	if (error)
+		return error;
+
+	return goodix_request_irq(ts);
+}
+
+static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+
 static const struct i2c_device_id goodix_ts_id[] = {
 	{ "GDIX1001:00", 0 },
 	{ }
@@ -736,6 +819,7 @@ static struct i2c_driver goodix_ts_driver = {
 		.name = "Goodix-TS",
 		.acpi_match_table = ACPI_PTR(goodix_acpi_match),
 		.of_match_table = of_match_ptr(goodix_of_match),
+		.pm = &goodix_pm_ops,
 	},
 };
 module_i2c_driver(goodix_ts_driver);
-- 
1.9.1

[PATCH v8 5/9] Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send

[Irina Tirdea]

Use goodix_i2c_write_u8 instead of i2c_master_send to simplify code.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 6314a24..c86c265 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -274,16 +274,11 @@ static void goodix_process_events(struct goodix_ts_data *ts)
  */
 static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 {
-	static const u8 end_cmd[] = {
-		GOODIX_READ_COOR_ADDR >> 8,
-		GOODIX_READ_COOR_ADDR & 0xff,
-		0
-	};
 	struct goodix_ts_data *ts = dev_id;
 
 	goodix_process_events(ts);
 
-	if (i2c_master_send(ts->client, end_cmd, sizeof(end_cmd)) < 0)
+	if (goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0) < 0)
 		dev_err(&ts->client->dev, "I2C write end_cmd error\n");
 
 	return IRQ_HANDLED;
-- 
1.9.1

[PATCH v8 6/9] Input: goodix - add support for ESD

[Irina Tirdea]

Add ESD (Electrostatic Discharge) protection mechanism.

The driver enables ESD protection in HW and checks a register
to determine if ESD occurred. If ESD is signalled by the HW,
the driver will reset the device.

The ESD poll time (in ms) can be set through the sysfs property
esd_timeout. If it is set to 0, ESD protection is disabled.
Recommended value is 2000 ms. The initial value for ESD timeout
can be set through esd-recovery-timeout-ms ACPI/DT property.
If there is no such property defined, ESD protection is disabled.
For ACPI 5.1, the property can be specified using _DSD properties:
 Device (STAC)
 {
     Name (_HID, "GDIX1001")
     ...

     Name (_DSD,  Package ()
     {
         ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
         Package ()
         {
             Package (2) { "esd-recovery-timeout-ms", Package(1) { 2000 }},
             ...
         }
     })
 }

The ESD protection mechanism is only available if the gpio pins
are properly initialized from ACPI/DT.

This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 .../bindings/input/touchscreen/goodix.txt          |   6 +
 drivers/input/touchscreen/goodix.c                 | 180 ++++++++++++++++++++-
 2 files changed, 178 insertions(+), 8 deletions(-)

diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index 7137881..4db3393 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -14,6 +14,12 @@ Required properties:
  - interrupts		: Interrupt to which the chip is connected
  - irq-gpio		: GPIO pin used for IRQ
  - reset-gpio		: GPIO pin used for reset
+Optional properties:
+
+ - esd-recovery-timeout-ms : ESD poll time (in milli seconds) for the driver to
+                            check if ESD occurred and in that case reset the
+                            device. ESD is disabled if this property is not set
+                            or is set to 0.
 
 Example:
 
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index c86c265..a271df9 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -45,10 +45,13 @@ struct goodix_ts_data {
 	u16 version;
 	char *cfg_name;
 	unsigned long irq_flags;
+	atomic_t esd_timeout;
+	struct delayed_work esd_work;
 };
 
 #define GOODIX_GPIO_INT_NAME		"irq"
 #define GOODIX_GPIO_RST_NAME		"reset"
+#define GOODIX_DEVICE_ESD_TIMEOUT_PROPERTY     "esd-recovery-timeout-ms"
 
 #define GOODIX_MAX_HEIGHT		4096
 #define GOODIX_MAX_WIDTH		4096
@@ -63,6 +66,8 @@ struct goodix_ts_data {
 /* Register defines */
 #define GOODIX_REG_COMMAND		0x8040
 #define GOODIX_CMD_SCREEN_OFF		0x05
+#define GOODIX_CMD_ESD_ENABLED		0xAA
+#define GOODIX_REG_ESD_CHECK		0x8041
 
 #define GOODIX_READ_COOR_ADDR		0x814E
 #define GOODIX_REG_CONFIG_DATA		0x8047
@@ -405,6 +410,117 @@ static int goodix_reset(struct goodix_ts_data *ts)
 	return goodix_int_sync(ts);
 }
 
+static void goodix_disable_esd(struct goodix_ts_data *ts)
+{
+	if (!atomic_read(&ts->esd_timeout))
+		return;
+	cancel_delayed_work_sync(&ts->esd_work);
+}
+
+static int goodix_enable_esd(struct goodix_ts_data *ts)
+{
+	int error, esd_timeout;
+
+	esd_timeout = atomic_read(&ts->esd_timeout);
+	if (!esd_timeout)
+		return 0;
+
+	error = goodix_i2c_write_u8(ts->client, GOODIX_REG_ESD_CHECK,
+				    GOODIX_CMD_ESD_ENABLED);
+	if (error) {
+		dev_err(&ts->client->dev, "Failed to enable ESD: %d\n", error);
+		return error;
+	}
+
+	schedule_delayed_work(&ts->esd_work, round_jiffies_relative(
+			      msecs_to_jiffies(esd_timeout)));
+	return 0;
+}
+
+static void goodix_esd_work(struct work_struct *work)
+{
+	struct goodix_ts_data *ts = container_of(work, struct goodix_ts_data,
+						 esd_work.work);
+	int retries = 3, error;
+	u8 esd_data[2];
+	const struct firmware *cfg = NULL;
+
+	while (--retries) {
+		error = goodix_i2c_read(ts->client, GOODIX_REG_COMMAND,
+					esd_data, sizeof(esd_data));
+		if (error)
+			continue;
+		if (esd_data[0] != GOODIX_CMD_ESD_ENABLED &&
+		    esd_data[1] == GOODIX_CMD_ESD_ENABLED) {
+			/* feed the watchdog */
+			goodix_i2c_write_u8(ts->client,
+					    GOODIX_REG_COMMAND,
+					    GOODIX_CMD_ESD_ENABLED);
+			break;
+		}
+	}
+
+	if (!retries) {
+		dev_dbg(&ts->client->dev, "Performing ESD recovery.\n");
+		goodix_free_irq(ts);
+		goodix_reset(ts);
+		error = request_firmware(&cfg, ts->cfg_name, &ts->client->dev);
+		if (!error) {
+			goodix_send_cfg(ts, cfg);
+			release_firmware(cfg);
+		}
+		goodix_request_irq(ts);
+		goodix_enable_esd(ts);
+		return;
+	}
+
+	schedule_delayed_work(&ts->esd_work, round_jiffies_relative(
+			      msecs_to_jiffies(atomic_read(&ts->esd_timeout))));
+}
+
+static ssize_t goodix_esd_timeout_show(struct device *dev,
+				       struct device_attribute *attr, char *buf)
+{
+	struct goodix_ts_data *ts = dev_get_drvdata(dev);
+
+	return scnprintf(buf, PAGE_SIZE, "%d\n", atomic_read(&ts->esd_timeout));
+}
+
+static ssize_t goodix_esd_timeout_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct goodix_ts_data *ts = dev_get_drvdata(dev);
+	int error, esd_timeout, new_esd_timeout;
+
+	error = kstrtouint(buf, 10, &new_esd_timeout);
+	if (error)
+		return error;
+
+	esd_timeout = atomic_read(&ts->esd_timeout);
+	if (esd_timeout && !new_esd_timeout)
+		goodix_disable_esd(ts);
+
+	atomic_set(&ts->esd_timeout, new_esd_timeout);
+	if (!esd_timeout && new_esd_timeout)
+		goodix_enable_esd(ts);
+
+	return count;
+}
+
+/* ESD timeout in ms. Default disabled (0). Recommended 2000 ms. */
+static DEVICE_ATTR(esd_timeout, S_IRUGO | S_IWUSR, goodix_esd_timeout_show,
+		   goodix_esd_timeout_store);
+
+static struct attribute *goodix_attrs[] = {
+	&dev_attr_esd_timeout.attr,
+	NULL
+};
+
+static const struct attribute_group goodix_attr_group = {
+	.attrs = goodix_attrs,
+};
+
 /**
  * goodix_get_gpio_config - Get GPIO config from ACPI/DT
  *
@@ -636,10 +752,13 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
 		if (error)
 			goto err_release_cfg;
 	}
-	goodix_configure_dev(ts);
+	error = goodix_configure_dev(ts);
+	if (error)
+		goto err_release_cfg;
+
+	goodix_enable_esd(ts);
 
 err_release_cfg:
-	kfree(ts->cfg_name);
 	release_firmware(cfg);
 }
 
@@ -647,7 +766,7 @@ static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	struct goodix_ts_data *ts;
-	int error;
+	int error, esd_timeout;
 
 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
 
@@ -662,6 +781,7 @@ static int goodix_ts_probe(struct i2c_client *client,
 
 	ts->client = client;
 	i2c_set_clientdata(client, ts);
+	INIT_DELAYED_WORK(&ts->esd_work, goodix_esd_work);
 
 	error = goodix_get_gpio_config(ts);
 	if (error == -EPROBE_DEFER)
@@ -691,11 +811,28 @@ static int goodix_ts_probe(struct i2c_client *client,
 	ts->cfg_len = goodix_get_cfg_len(ts->id);
 
 	if (ts->gpiod_int && ts->gpiod_rst) {
+		error = device_property_read_u32(&ts->client->dev,
+					GOODIX_DEVICE_ESD_TIMEOUT_PROPERTY,
+					&esd_timeout);
+		if (!error)
+			atomic_set(&ts->esd_timeout, esd_timeout);
+
+		error = sysfs_create_group(&client->dev.kobj,
+					   &goodix_attr_group);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to create sysfs group: %d\n",
+				error);
+			return error;
+		}
+
 		/* update device config */
 		ts->cfg_name = kasprintf(GFP_KERNEL, "goodix_%d_cfg.bin",
 					 ts->id);
-		if (!ts->cfg_name)
-			return -ENOMEM;
+		if (!ts->cfg_name) {
+			error = -ENOMEM;
+			goto err_sysfs_remove_group;
+		}
 
 		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
 						&client->dev, GFP_KERNEL, ts,
@@ -704,14 +841,35 @@ static int goodix_ts_probe(struct i2c_client *client,
 			dev_err(&client->dev,
 				"Failed to invoke firmware loader: %d\n",
 				error);
-			kfree(ts->cfg_name);
-			return error;
+			goto err_free_cfg_name;
 		}
 
 		return 0;
 	}
 
 	return goodix_configure_dev(ts);
+
+err_free_cfg_name:
+	if (ts->gpiod_int && ts->gpiod_rst)
+		kfree(ts->cfg_name);
+err_sysfs_remove_group:
+	if (ts->gpiod_int && ts->gpiod_rst)
+		sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
+	return error;
+}
+
+static int goodix_ts_remove(struct i2c_client *client)
+{
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
+	goodix_disable_esd(ts);
+	kfree(ts->cfg_name);
+
+	return 0;
 }
 
 static int __maybe_unused goodix_suspend(struct device *dev)
@@ -724,6 +882,7 @@ static int __maybe_unused goodix_suspend(struct device *dev)
 	if (!ts->gpiod_int || !ts->gpiod_rst)
 		return 0;
 
+	goodix_disable_esd(ts);
 	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
 	goodix_free_irq(ts);
 	/* Output LOW on the INT pin for 5 ms */
@@ -774,7 +933,11 @@ static int __maybe_unused goodix_resume(struct device *dev)
 	if (error)
 		return error;
 
-	return goodix_request_irq(ts);
+	error = goodix_request_irq(ts);
+	if (error)
+		return error;
+
+	return goodix_enable_esd(ts);
 }
 
 static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
@@ -809,6 +972,7 @@ MODULE_DEVICE_TABLE(of, goodix_of_match);
 
 static struct i2c_driver goodix_ts_driver = {
 	.probe = goodix_ts_probe,
+	.remove = goodix_ts_remove,
 	.id_table = goodix_ts_id,
 	.driver = {
 		.name = "Goodix-TS",
-- 
1.9.1

[PATCH v8 7/9] Input: goodix - add sysfs interface to dump config

[Irina Tirdea]

Goodix devices have a configuration information register area that
specify various parameters for the device. The configuration information
has a specific format described in the Goodix datasheet. It includes X/Y
resolution, maximum supported touch points, interrupt flags, various
sesitivity factors and settings for advanced features (like gesture
recognition).

Export a sysfs interface that would allow reading the configuration
information. The default device configuration can be used as a starting
point for creating a valid configuration firmware used by the device at
init time to update its configuration.

This sysfs interface will be exported only if the gpio pins are properly
initialized from ACPI/DT.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index a271df9..01a2634 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -508,12 +508,35 @@ static ssize_t goodix_esd_timeout_store(struct device *dev,
 	return count;
 }
 
+static ssize_t goodix_dump_config_show(struct device *dev,
+				       struct device_attribute *attr, char *buf)
+{
+	struct goodix_ts_data *ts = dev_get_drvdata(dev);
+	u8 config[GOODIX_CONFIG_MAX_LENGTH];
+	int error, count = 0, i;
+
+	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
+				config, ts->cfg_len);
+	if (error) {
+		dev_warn(&ts->client->dev,
+			 "Error reading config (%d)\n",  error);
+		return error;
+	}
+
+	for (i = 0; i < ts->cfg_len; i++)
+		count += scnprintf(buf + count, PAGE_SIZE - count, "%02x ",
+				   config[i]);
+	return count;
+}
+
 /* ESD timeout in ms. Default disabled (0). Recommended 2000 ms. */
 static DEVICE_ATTR(esd_timeout, S_IRUGO | S_IWUSR, goodix_esd_timeout_show,
 		   goodix_esd_timeout_store);
+static DEVICE_ATTR(dump_config, S_IRUGO, goodix_dump_config_show, NULL);
 
 static struct attribute *goodix_attrs[] = {
 	&dev_attr_esd_timeout.attr,
+	&dev_attr_dump_config.attr,
 	NULL
 };
 
-- 
1.9.1

[PATCH v8 8/9] Input: goodix - add runtime power management support

[Irina Tirdea]

Add support for runtime power management so that the device is
turned off when not used (when the userspace holds no open
handles of the input device). The device uses autosuspend with a
default delay of 2 seconds, so the device will suspend if no
handles to it are open for 2 seconds.

The runtime management support is only available if the gpio pins
are properly initialized from ACPI/DT.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 152 +++++++++++++++++++++++++++++++++----
 1 file changed, 138 insertions(+), 14 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 01a2634..b958b37 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -28,6 +28,7 @@
 #include <linux/slab.h>
 #include <linux/acpi.h>
 #include <linux/of.h>
+#include <linux/pm_runtime.h>
 #include <asm/unaligned.h>
 
 struct goodix_ts_data {
@@ -47,6 +48,10 @@ struct goodix_ts_data {
 	unsigned long irq_flags;
 	atomic_t esd_timeout;
 	struct delayed_work esd_work;
+	bool suspended;
+	atomic_t open_count;
+	/* Protects power management calls and access to suspended flag */
+	struct mutex mutex;
 };
 
 #define GOODIX_GPIO_INT_NAME		"irq"
@@ -77,6 +82,8 @@ struct goodix_ts_data {
 #define MAX_CONTACTS_LOC	5
 #define TRIGGER_LOC		6
 
+#define GOODIX_AUTOSUSPEND_DELAY_MS	2000
+
 static const unsigned long goodix_irq_flags[] = {
 	IRQ_TYPE_EDGE_RISING,
 	IRQ_TYPE_EDGE_FALLING,
@@ -192,6 +199,32 @@ static int goodix_get_cfg_len(u16 id)
 	}
 }
 
+static int goodix_set_power_state(struct goodix_ts_data *ts, bool on)
+{
+	int error;
+
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	if (on) {
+		error = pm_runtime_get_sync(&ts->client->dev);
+	} else {
+		pm_runtime_mark_last_busy(&ts->client->dev);
+		error = pm_runtime_put_autosuspend(&ts->client->dev);
+	}
+
+	if (error < 0) {
+		dev_err(&ts->client->dev,
+			"failed to change power state to %d\n", on);
+		if (on)
+			pm_runtime_put_noidle(&ts->client->dev);
+
+		return error;
+	}
+
+	return 0;
+}
+
 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
 {
 	int touch_num;
@@ -498,11 +531,13 @@ static ssize_t goodix_esd_timeout_store(struct device *dev,
 		return error;
 
 	esd_timeout = atomic_read(&ts->esd_timeout);
-	if (esd_timeout && !new_esd_timeout)
+	if (esd_timeout && !new_esd_timeout &&
+	    pm_runtime_active(&ts->client->dev))
 		goodix_disable_esd(ts);
 
 	atomic_set(&ts->esd_timeout, new_esd_timeout);
-	if (!esd_timeout && new_esd_timeout)
+	if (!esd_timeout && new_esd_timeout &&
+	    pm_runtime_active(&ts->client->dev))
 		goodix_enable_esd(ts);
 
 	return count;
@@ -515,17 +550,23 @@ static ssize_t goodix_dump_config_show(struct device *dev,
 	u8 config[GOODIX_CONFIG_MAX_LENGTH];
 	int error, count = 0, i;
 
+	error = goodix_set_power_state(ts, true);
+	if (error)
+		return error;
 	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
 				config, ts->cfg_len);
 	if (error) {
 		dev_warn(&ts->client->dev,
 			 "Error reading config (%d)\n",  error);
+		goodix_set_power_state(ts, false);
 		return error;
 	}
+	goodix_set_power_state(ts, false);
 
 	for (i = 0; i < ts->cfg_len; i++)
 		count += scnprintf(buf + count, PAGE_SIZE - count, "%02x ",
 				   config[i]);
+
 	return count;
 }
 
@@ -544,6 +585,26 @@ static const struct attribute_group goodix_attr_group = {
 	.attrs = goodix_attrs,
 };
 
+static int goodix_open(struct input_dev *input_dev)
+{
+	struct goodix_ts_data *ts = input_get_drvdata(input_dev);
+	int error;
+
+	error = goodix_set_power_state(ts, true);
+	if (error)
+		return error;
+	atomic_inc(&ts->open_count);
+	return 0;
+}
+
+static void goodix_close(struct input_dev *input_dev)
+{
+	struct goodix_ts_data *ts = input_get_drvdata(input_dev);
+
+	goodix_set_power_state(ts, false);
+	atomic_dec(&ts->open_count);
+}
+
 /**
  * goodix_get_gpio_config - Get GPIO config from ACPI/DT
  *
@@ -715,6 +776,9 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts)
 	ts->input_dev->id.vendor = 0x0416;
 	ts->input_dev->id.product = ts->id;
 	ts->input_dev->id.version = ts->version;
+	ts->input_dev->open = goodix_open;
+	ts->input_dev->close = goodix_close;
+	input_set_drvdata(ts->input_dev, ts);
 
 	error = input_register_device(ts->input_dev);
 	if (error) {
@@ -762,7 +826,8 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
  * @ts: our goodix_ts_data pointer
  *
  * request_firmware_wait callback that finishes
- * initialization of the device.
+ * initialization of the device. This will only be called
+ * when ts->gpiod_int and ts->gpiod_rst are properly initialized.
  */
 static void goodix_config_cb(const struct firmware *cfg, void *ctx)
 {
@@ -781,6 +846,19 @@ static void goodix_config_cb(const struct firmware *cfg, void *ctx)
 
 	goodix_enable_esd(ts);
 
+	pm_runtime_set_autosuspend_delay(&ts->client->dev,
+					 GOODIX_AUTOSUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(&ts->client->dev);
+	error = pm_runtime_set_active(&ts->client->dev);
+	if (error) {
+		dev_err(&ts->client->dev, "failed to set active: %d\n", error);
+		goto err_release_cfg;
+	}
+	pm_runtime_enable(&ts->client->dev);
+	/* Must not suspend immediately after device initialization */
+	pm_runtime_mark_last_busy(&ts->client->dev);
+	pm_request_autosuspend(&ts->client->dev);
+
 err_release_cfg:
 	release_firmware(cfg);
 }
@@ -805,6 +883,7 @@ static int goodix_ts_probe(struct i2c_client *client,
 	ts->client = client;
 	i2c_set_clientdata(client, ts);
 	INIT_DELAYED_WORK(&ts->esd_work, goodix_esd_work);
+	mutex_init(&ts->mutex);
 
 	error = goodix_get_gpio_config(ts);
 	if (error == -EPROBE_DEFER)
@@ -888,6 +967,9 @@ static int goodix_ts_remove(struct i2c_client *client)
 	if (!ts->gpiod_int || !ts->gpiod_rst)
 		return 0;
 
+	pm_runtime_disable(&client->dev);
+	pm_runtime_set_suspended(&client->dev);
+	pm_runtime_put_noidle(&client->dev);
 	sysfs_remove_group(&client->dev.kobj, &goodix_attr_group);
 	goodix_disable_esd(ts);
 	kfree(ts->cfg_name);
@@ -895,16 +977,21 @@ static int goodix_ts_remove(struct i2c_client *client)
 	return 0;
 }
 
-static int __maybe_unused goodix_suspend(struct device *dev)
+static int __maybe_unused goodix_sleep(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct goodix_ts_data *ts = i2c_get_clientdata(client);
-	int error;
+	int error = 0;
 
 	/* We need gpio pins to suspend/resume */
 	if (!ts->gpiod_int || !ts->gpiod_rst)
 		return 0;
 
+	mutex_lock(&ts->mutex);
+
+	if (ts->suspended)
+		goto out_error;
+
 	goodix_disable_esd(ts);
 	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
 	goodix_free_irq(ts);
@@ -912,7 +999,7 @@ static int __maybe_unused goodix_suspend(struct device *dev)
 	error = gpiod_direction_output(ts->gpiod_int, 0);
 	if (error) {
 		goodix_request_irq(ts);
-		return error;
+		goto out_error;
 	}
 	usleep_range(5000, 6000);
 
@@ -922,7 +1009,8 @@ static int __maybe_unused goodix_suspend(struct device *dev)
 		dev_err(&ts->client->dev, "Screen off command failed\n");
 		gpiod_direction_input(ts->gpiod_int);
 		goodix_request_irq(ts);
-		return -EAGAIN;
+		error = -EAGAIN;
+		goto out_error;
 	}
 
 	/*
@@ -931,39 +1019,75 @@ static int __maybe_unused goodix_suspend(struct device *dev)
 	 * sooner, delay 58ms here.
 	 */
 	msleep(58);
+	ts->suspended = true;
+	mutex_unlock(&ts->mutex);
 	return 0;
+
+out_error:
+	mutex_unlock(&ts->mutex);
+	return error;
 }
 
-static int __maybe_unused goodix_resume(struct device *dev)
+static int __maybe_unused goodix_wakeup(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct goodix_ts_data *ts = i2c_get_clientdata(client);
-	int error;
+	int error = 0;
 
 	if (!ts->gpiod_int || !ts->gpiod_rst)
 		return 0;
 
+	mutex_lock(&ts->mutex);
+
+	if (!ts->suspended)
+		goto out_error;
+
 	/*
 	 * Exit sleep mode by outputting HIGH level to INT pin
 	 * for 2ms~5ms.
 	 */
 	error = gpiod_direction_output(ts->gpiod_int, 1);
 	if (error)
-		return error;
+		goto out_error;
 	usleep_range(2000, 5000);
 
 	error = goodix_int_sync(ts);
 	if (error)
-		return error;
+		goto out_error;
 
 	error = goodix_request_irq(ts);
 	if (error)
-		return error;
+		goto out_error;
 
-	return goodix_enable_esd(ts);
+	error = goodix_enable_esd(ts);
+	if (error)
+		goto out_error;
+
+	ts->suspended = false;
+	mutex_unlock(&ts->mutex);
+
+	return 0;
+
+out_error:
+	mutex_unlock(&ts->mutex);
+	return error;
+}
+
+static int __maybe_unused goodix_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+	if (!atomic_read(&ts->open_count))
+		return 0;
+
+	return goodix_wakeup(dev);
 }
 
-static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+static const struct dev_pm_ops goodix_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(goodix_sleep, goodix_resume)
+	SET_RUNTIME_PM_OPS(goodix_sleep, goodix_wakeup, NULL)
+};
 
 static const struct i2c_device_id goodix_ts_id[] = {
 	{ "GDIX1001:00", 0 },
-- 
1.9.1

[PATCH v8 9/9] Input: goodix - sort includes using inverse Xmas tree order

[Irina Tirdea]

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
---
 drivers/input/touchscreen/goodix.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index b958b37..22bfc4b 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -14,21 +14,22 @@
  * Software Foundation; version 2 of the License.
  */
 
-#include <linux/kernel.h>
-#include <linux/dmi.h>
+#include <linux/pm_runtime.h>
+#include <linux/interrupt.h>
 #include <linux/firmware.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/input.h>
 #include <linux/input/mt.h>
+#include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/delay.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/slab.h>
+#include <linux/input.h>
 #include <linux/acpi.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/dmi.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
 #include <linux/of.h>
-#include <linux/pm_runtime.h>
+
 #include <asm/unaligned.h>
 
 struct goodix_ts_data {
-- 
1.9.1

Re: [PATCH v8 0/9] Goodix touchscreen enhancements

[Arnd Bergmann]

On Thursday 08 October 2015 17:23:42 Irina Tirdea wrote:
> Add several enhancements to the Goodix touchscreen driver.
> 
> The new functionality is only available for devices that
> declare named gpio pins for interrupt and reset in their
> ACPI/DT configuration.
> 
> Thanks,
> Irina
> 
> Changes in v8:
>  - only allow new functionality for devices that declare named
> gpios (using _DSD properties in ACPI or named DT properties)
> 
> 

Looks much cleaner this way, thanks!

One remaining question: how would you handle the case where
the hardware doesn't support configuring the int-gpios line
as output but you still want to use the named gpios?

I assume you have that case covered, but I don't see it immediately.

	Arnd

RE: [PATCH v8 0/9] Goodix touchscreen enhancements

[Tirdea, Irina]

> -----Original Message-----
> From: linux-input-owner@vger.kernel.org [mailto:linux-input-owner@vger.kernel.org] On Behalf Of Arnd Bergmann
> Sent: 08 October, 2015 17:32
> To: Tirdea, Irina
> Cc: Dmitry Torokhov; Bastien Nocera; Aleksei Mamlin; linux-input@vger.kernel.org; Mark Rutland; Purdila, Octavian; linux-
> kernel@vger.kernel.org; devicetree@vger.kernel.org
> Subject: Re: [PATCH v8 0/9] Goodix touchscreen enhancements
> 
> On Thursday 08 October 2015 17:23:42 Irina Tirdea wrote:
> > Add several enhancements to the Goodix touchscreen driver.
> >
> > The new functionality is only available for devices that
> > declare named gpio pins for interrupt and reset in their
> > ACPI/DT configuration.
> >
> > Thanks,
> > Irina
> >
> > Changes in v8:
> >  - only allow new functionality for devices that declare named
> > gpios (using _DSD properties in ACPI or named DT properties)
> >
> >
> 
> Looks much cleaner this way, thanks!
> 
> One remaining question: how would you handle the case where
> the hardware doesn't support configuring the int-gpios line
> as output but you still want to use the named gpios?
> 

The only reason to use named gpios is to enable the new functionality
introduced by this patch set (mainly reset and power management).
You cannot use only one gpio either (e.g. only reset gpio but not the
interrupt gpio), you need both for this functionality to work.

If the hardware does not support using the interrupt gpio pin as output,
it should not declare the named int-gpio pin in ACPI. It is true that
we might later run into platforms that declare the int-gpio pin even if it
does not actually work (just like we now have the indexed gpio pins).
I could have added an additional property for this as you first suggested,
but if we can modify the ACPI to add it, we could simply remove the
named interrupt pin instead (that does not work anyway).

> I assume you have that case covered, but I don't see it immediately.
> 
> 	Arnd
> --
> To unsubscribe from this list: send the line "unsubscribe linux-input" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v8 0/9] Goodix touchscreen enhancements

[Arnd Bergmann]

On Friday 09 October 2015 11:02:01 Tirdea, Irina wrote:
> > -----Original Message-----
> > From: linux-input-owner@vger.kernel.org [mailto:linux-input-owner@vger.kernel.org] On Behalf Of Arnd Bergmann
> > Sent: 08 October, 2015 17:32
> > To: Tirdea, Irina
> > Cc: Dmitry Torokhov; Bastien Nocera; Aleksei Mamlin; linux-input@vger.kernel.org; Mark Rutland; Purdila, Octavian; linux-
> > kernel@vger.kernel.org; devicetree@vger.kernel.org
> > Subject: Re: [PATCH v8 0/9] Goodix touchscreen enhancements
> > 
> > On Thursday 08 October 2015 17:23:42 Irina Tirdea wrote:
> > > Add several enhancements to the Goodix touchscreen driver.
> > >
> > > The new functionality is only available for devices that
> > > declare named gpio pins for interrupt and reset in their
> > > ACPI/DT configuration.
> > >
> > > Thanks,
> > > Irina
> > >
> > > Changes in v8:
> > >  - only allow new functionality for devices that declare named
> > > gpios (using _DSD properties in ACPI or named DT properties)
> > >
> > >
> > 
> > Looks much cleaner this way, thanks!
> > 
> > One remaining question: how would you handle the case where
> > the hardware doesn't support configuring the int-gpios line
> > as output but you still want to use the named gpios?
> > 
> 
> The only reason to use named gpios is to enable the new functionality
> introduced by this patch set (mainly reset and power management).
> You cannot use only one gpio either (e.g. only reset gpio but not the
> interrupt gpio), you need both for this functionality to work.
> 
> If the hardware does not support using the interrupt gpio pin as output,
> it should not declare the named int-gpio pin in ACPI. It is true that
> we might later run into platforms that declare the int-gpio pin even if it
> does not actually work (just like we now have the indexed gpio pins).
> I could have added an additional property for this as you first suggested,
> but if we can modify the ACPI to add it, we could simply remove the
> named interrupt pin instead (that does not work anyway).

Ok, got it. Thanks,

	Arnd

Re: [PATCH v8 2/9] Input: goodix - reset device at init

[Bastien Nocera]

On Thu, 2015-10-08 at 17:23 +0300, Irina Tirdea wrote:
> After power on, it is recommended that the driver resets the device.
> The reset procedure timing is described in the datasheet and is used
> at device init (before writing device configuration) and
> for power management. It is a sequence of setting the interrupt
> and reset pins high/low at specific timing intervals. This procedure
> also includes setting the slave address to the one specified in the
> ACPI/device tree.
> 
> This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
> driver gt9xx.c for Android (publicly available in Android kernel
> trees for various devices).
> 
> For reset the driver needs to control the interrupt and
> reset gpio pins (configured through ACPI/device tree). For devices
> that do not have the gpio pins properly declared, the functionality
> depending on these pins will not be available, but the device can
> still
> be used with basic functionality.
> 
> For both device tree and ACPI, the interrupt gpio pin configuration
> is
> read from the "irq-gpio" property and the reset pin configuration is
> read from the "reset-gpio" property. For ACPI 5.1, named properties
> can be specified using the _DSD section. This functionality will not
> be
> available for devices that use indexed gpio pins declared in the _CRS
> section (we need to provide backward compatibility with devices
> that do not support using the interrupt gpio pin as output).
> 
> For ACPI, the pins can be specified using ACPI 5.1:
> Device (STAC)
> {
>     Name (_HID, "GDIX1001")
>     ...
> 
>     Method (_CRS, 0, Serialized)
>     {
>         Name (RBUF, ResourceTemplate ()
>         {
>             I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
>                 AddressingMode7Bit, "\\I2C0",
>                 0x00, ResourceConsumer, ,
>                 )
> 
>             GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
>                 "\\I2C0", 0x00, ResourceConsumer, ,
>                  )
>                  {   // Pin list
>                      0
>                  }
> 
>             GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
>                 IoRestrictionOutputOnly, "\\I2C0", 0x00,
>                 ResourceConsumer, ,
>                 )
>                 {
>                      1
>                 }
>         })
>         Return (RBUF)
>     }
> 
>     Name (_DSD,  Package ()
>     {
>         ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
>         Package ()
>         {
>             Package (2) {"irq-gpio", Package() {^STAC, 0, 0, 0 }},
>             Package (2) {"reset-gpio", Package() {^STAC, 1, 0, 0 }},
>             ...
>         }
>     }
> 
> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
> Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>

Didn't actually cause problems on my system, and the documentation
looks good.

Acked-by: Bastien Nocera <hadess@hadess.net>

Re: [PATCH v8 2/9] Input: goodix - reset device at init

[Bastien Nocera]

On Thu, 2015-10-08 at 17:23 +0300, Irina Tirdea wrote:
> After power on, it is recommended that the driver resets the device.
> The reset procedure timing is described in the datasheet and is used
> at device init (before writing device configuration) and
> for power management. It is a sequence of setting the interrupt
> and reset pins high/low at specific timing intervals. This procedure
> also includes setting the slave address to the one specified in the
> ACPI/device tree.
> 
> This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
> driver gt9xx.c for Android (publicly available in Android kernel
> trees for various devices).
> 
> For reset the driver needs to control the interrupt and
> reset gpio pins (configured through ACPI/device tree). For devices
> that do not have the gpio pins properly declared, the functionality
> depending on these pins will not be available, but the device can
> still
> be used with basic functionality.
> 
> For both device tree and ACPI, the interrupt gpio pin configuration
> is
> read from the "irq-gpio" property and the reset pin configuration is
> read from the "reset-gpio" property. For ACPI 5.1, named properties
> can be specified using the _DSD section. This functionality will not
> be
> available for devices that use indexed gpio pins declared in the _CRS
> section (we need to provide backward compatibility with devices
> that do not support using the interrupt gpio pin as output).
> 
> For ACPI, the pins can be specified using ACPI 5.1:
> Device (STAC)
> {
>     Name (_HID, "GDIX1001")
>     ...
> 
>     Method (_CRS, 0, Serialized)
>     {
>         Name (RBUF, ResourceTemplate ()
>         {
>             I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
>                 AddressingMode7Bit, "\\I2C0",
>                 0x00, ResourceConsumer, ,
>                 )
> 
>             GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
>                 "\\I2C0", 0x00, ResourceConsumer, ,
>                  )
>                  {   // Pin list
>                      0
>                  }
> 
>             GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
>                 IoRestrictionOutputOnly, "\\I2C0", 0x00,
>                 ResourceConsumer, ,
>                 )
>                 {
>                      1
>                 }
>         })
>         Return (RBUF)
>     }
> 
>     Name (_DSD,  Package ()
>     {
>         ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
>         Package ()
>         {
>             Package (2) {"irq-gpio", Package() {^STAC, 0, 0, 0 }},
>             Package (2) {"reset-gpio", Package() {^STAC, 1, 0, 0 }},
>             ...
>         }
>     }
> 
> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
> Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>

Didn't actually cause problems on my system, and the documentation
looks good.

Acked-by: Bastien Nocera <hadess@hadess.net>

--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v8 0/9] Goodix touchscreen enhancements

[Bastien Nocera]

On Thu, 2015-10-08 at 17:23 +0300, Irina Tirdea wrote:
> Add several enhancements to the Goodix touchscreen driver.
> 
> The new functionality is only available for devices that
> declare named gpio pins for interrupt and reset in their
> ACPI/DT configuration.


You can add

Tested-by: Bastien Nocera <hadess@hadess.net>

to the whole patchset. The features that don't work on my system
(broken GPIO configuration) don't actually cause problems, the
configuration dump doesn't appear, etc.

In the future, I should probably try and see _why_ it doesn't work (or
maybe the hardware maker didn't think it was necessary to flog their
cheap hardware).

Thanks a lot for your patience.

Cheers

Re: [PATCH v8 0/9] Goodix touchscreen enhancements

[Aleksei Mamlin]

On Thu,  8 Oct 2015 17:23:42 +0300
Irina Tirdea <irina.tirdea@intel.com> wrote:

> Add several enhancements to the Goodix touchscreen driver.
> 
> The new functionality is only available for devices that
> declare named gpio pins for interrupt and reset in their
> ACPI/DT configuration.
> 

I tested this patchset on ARM tablet Wexler TAB7200 with GT911 touchscreen 
controller. All works fine, so you can add

Tested-by: Aleksei Mamlin <mamlinav@gmail.com>

>
> Thanks,
> Irina
> 
> Changes in v8:
>  - only allow new functionality for devices that declare named
> gpios (using _DSD properties in ACPI or named DT properties)
> 
> Changes in v7:
>  - add dmi quirk to skip gpio pins setup and functionality that
> depends on them for Onda v975w, WinBook TW100 and WinBook TW700.
>  - add support for named gpio pins
>  - rework the runtime pm patch to fix a couple of issues
>  - sort includes using inverse Xmas tree ordering
> 
> Changes in v6:
>  - skip runtime power manangent calls in open/close if the device
> ACPI/DT configuration does not declare interrupt and reset gpio pins.
>  - reset the device before starting i2c communication
>  - add Bastien's ack to the first 2 patches
> 
> Changes in v5:
>  - add some more style cleanup (reorder includes, use error instead
> of ret for return values)
>  - add runtime power management patch
> 
> Changes in v4:
>  - use dmi quirk to determine the order of irq and reset pins
>  - use actual config length depending on device
>  - add sysfs interface to dump config
>  - initialize esd timeout from ACPI/DT properly
> 
> Changes in v3:
>  - dropped the first 3 patches that got merged
>  - handle -EPROBE_DEFER and -ENOENT for gpio pins
>  - skip functionality depending on the gpio pins if the pins are not
> properly initialized from ACPI/DT (reset, write config, power management,
> ESD)
>  - dropped #ifdef CONFIG_PM_SLEEP and annotated with __maybe_unused instead
>  - use sysfs property to set ESD timeout instead of ACPI/DT property
>  - use request_firmware_nowait to read configuration firmware and use
> defaults if firmware is not found
>  - use ACPI IDs to determine the order of the GPIO pins in the ACPI tables
> (interrupt pin first or reset pin first)
> 
> Changes in v2:
>  - use request_firmware instead of ACPI/DT property for config
>  - dropped "input: goodix: add ACPI IDs for GT911 and GT9271" patch
>  - add ACPI DSDT excerpt in commit message where necessary
>  - add comments for suspend/resume sleep values
>  - dropped the checkpatch fixes that did not make sense
>  - added Bastien's ack to the first patch
> 
> Irina Tirdea (9):
>   Input: goodix - use actual config length for each device type
>   Input: goodix - reset device at init
>   Input: goodix - write configuration data to device
>   Input: goodix - add power management support
>   Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
>   Input: goodix - add support for ESD
>   Input: goodix - add sysfs interface to dump config
>   Input: goodix - add runtime power management support
>   Input: goodix - sort includes using inverse Xmas tree order
> 
>  .../bindings/input/touchscreen/goodix.txt          |  11 +
>  drivers/input/touchscreen/goodix.c                 | 766 +++++++++++++++++++--
>  2 files changed, 732 insertions(+), 45 deletions(-)
> 
> -- 
> 1.9.1
> 


-- 
Thanks and regards,
Aleksei Mamlin

Re: [PATCH v8 0/9] Goodix touchscreen enhancements

[Aleksei Mamlin]

On Thu,  8 Oct 2015 17:23:42 +0300
Irina Tirdea <irina.tirdea-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org> wrote:

> Add several enhancements to the Goodix touchscreen driver.
> 
> The new functionality is only available for devices that
> declare named gpio pins for interrupt and reset in their
> ACPI/DT configuration.
> 

I tested this patchset on ARM tablet Wexler TAB7200 with GT911 touchscreen 
controller. All works fine, so you can add

Tested-by: Aleksei Mamlin <mamlinav-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

>
> Thanks,
> Irina
> 
> Changes in v8:
>  - only allow new functionality for devices that declare named
> gpios (using _DSD properties in ACPI or named DT properties)
> 
> Changes in v7:
>  - add dmi quirk to skip gpio pins setup and functionality that
> depends on them for Onda v975w, WinBook TW100 and WinBook TW700.
>  - add support for named gpio pins
>  - rework the runtime pm patch to fix a couple of issues
>  - sort includes using inverse Xmas tree ordering
> 
> Changes in v6:
>  - skip runtime power manangent calls in open/close if the device
> ACPI/DT configuration does not declare interrupt and reset gpio pins.
>  - reset the device before starting i2c communication
>  - add Bastien's ack to the first 2 patches
> 
> Changes in v5:
>  - add some more style cleanup (reorder includes, use error instead
> of ret for return values)
>  - add runtime power management patch
> 
> Changes in v4:
>  - use dmi quirk to determine the order of irq and reset pins
>  - use actual config length depending on device
>  - add sysfs interface to dump config
>  - initialize esd timeout from ACPI/DT properly
> 
> Changes in v3:
>  - dropped the first 3 patches that got merged
>  - handle -EPROBE_DEFER and -ENOENT for gpio pins
>  - skip functionality depending on the gpio pins if the pins are not
> properly initialized from ACPI/DT (reset, write config, power management,
> ESD)
>  - dropped #ifdef CONFIG_PM_SLEEP and annotated with __maybe_unused instead
>  - use sysfs property to set ESD timeout instead of ACPI/DT property
>  - use request_firmware_nowait to read configuration firmware and use
> defaults if firmware is not found
>  - use ACPI IDs to determine the order of the GPIO pins in the ACPI tables
> (interrupt pin first or reset pin first)
> 
> Changes in v2:
>  - use request_firmware instead of ACPI/DT property for config
>  - dropped "input: goodix: add ACPI IDs for GT911 and GT9271" patch
>  - add ACPI DSDT excerpt in commit message where necessary
>  - add comments for suspend/resume sleep values
>  - dropped the checkpatch fixes that did not make sense
>  - added Bastien's ack to the first patch
> 
> Irina Tirdea (9):
>   Input: goodix - use actual config length for each device type
>   Input: goodix - reset device at init
>   Input: goodix - write configuration data to device
>   Input: goodix - add power management support
>   Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
>   Input: goodix - add support for ESD
>   Input: goodix - add sysfs interface to dump config
>   Input: goodix - add runtime power management support
>   Input: goodix - sort includes using inverse Xmas tree order
> 
>  .../bindings/input/touchscreen/goodix.txt          |  11 +
>  drivers/input/touchscreen/goodix.c                 | 766 +++++++++++++++++++--
>  2 files changed, 732 insertions(+), 45 deletions(-)
> 
> -- 
> 1.9.1
> 


-- 
Thanks and regards,
Aleksei Mamlin
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v8 2/9] Input: goodix - reset device at init

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 3626 bytes --]

Hi Irina,

[auto build test ERROR on v4.3-rc4 -- if it's inappropriate base, please ignore]

config: x86_64-randconfig-h0-10110617 (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All errors (new ones prefixed by >>):

   drivers/input/touchscreen/goodix.c: In function 'goodix_int_sync':
>> drivers/input/touchscreen/goodix.c:250:10: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
     error = gpiod_direction_output(ts->gpiod_int, 0);
             ^
>> drivers/input/touchscreen/goodix.c:255:9: error: implicit declaration of function 'gpiod_direction_input' [-Werror=implicit-function-declaration]
     return gpiod_direction_input(ts->gpiod_int);
            ^
   drivers/input/touchscreen/goodix.c: In function 'goodix_get_gpio_config':
>> drivers/input/touchscreen/goodix.c:304:10: error: implicit declaration of function 'devm_gpiod_get' [-Werror=implicit-function-declaration]
     gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
             ^
>> drivers/input/touchscreen/goodix.c:304:52: error: 'GPIOD_IN' undeclared (first use in this function)
     gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
                                                       ^
   drivers/input/touchscreen/goodix.c:304:52: note: each undeclared identifier is reported only once for each function it appears in
   cc1: some warnings being treated as errors

vim +/gpiod_direction_output +250 drivers/input/touchscreen/goodix.c

   244	}
   245	
   246	static int goodix_int_sync(struct goodix_ts_data *ts)
   247	{
   248		int error;
   249	
 > 250		error = gpiod_direction_output(ts->gpiod_int, 0);
   251		if (error)
   252			return error;
   253		msleep(50);				/* T5: 50ms */
   254	
 > 255		return gpiod_direction_input(ts->gpiod_int);
   256	}
   257	
   258	/**
   259	 * goodix_reset - Reset device during power on
   260	 *
   261	 * @ts: goodix_ts_data pointer
   262	 */
   263	static int goodix_reset(struct goodix_ts_data *ts)
   264	{
   265		int error;
   266	
   267		/* begin select I2C slave addr */
   268		error = gpiod_direction_output(ts->gpiod_rst, 0);
   269		if (error)
   270			return error;
   271		msleep(20);				/* T2: > 10ms */
   272		/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
   273		error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
   274		if (error)
   275			return error;
   276		usleep_range(100, 2000);		/* T3: > 100us */
   277		error = gpiod_direction_output(ts->gpiod_rst, 1);
   278		if (error)
   279			return error;
   280		usleep_range(6000, 10000);		/* T4: > 5ms */
   281		/* end select I2C slave addr */
   282		error = gpiod_direction_input(ts->gpiod_rst);
   283		if (error)
   284			return error;
   285		return goodix_int_sync(ts);
   286	}
   287	
   288	/**
   289	 * goodix_get_gpio_config - Get GPIO config from ACPI/DT
   290	 *
   291	 * @ts: goodix_ts_data pointer
   292	 */
   293	static int goodix_get_gpio_config(struct goodix_ts_data *ts)
   294	{
   295		int error;
   296		struct device *dev;
   297		struct gpio_desc *gpiod;
   298	
   299		if (!ts->client)
   300			return -EINVAL;
   301		dev = &ts->client->dev;
   302	
   303		/* Get the interrupt GPIO pin number */
 > 304		gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
   305		if (IS_ERR(gpiod)) {
   306			error = PTR_ERR(gpiod);
   307			if (error != -EPROBE_DEFER)

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 25511 bytes --]

Re: [PATCH v8 2/9] Input: goodix - reset device at init

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 3626 bytes --]

Hi Irina,

[auto build test ERROR on v4.3-rc4 -- if it's inappropriate base, please ignore]

config: x86_64-randconfig-h0-10110617 (attached as .config)
reproduce:
        # save the attached .config to linux build tree
        make ARCH=x86_64 

All errors (new ones prefixed by >>):

   drivers/input/touchscreen/goodix.c: In function 'goodix_int_sync':
>> drivers/input/touchscreen/goodix.c:250:10: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
     error = gpiod_direction_output(ts->gpiod_int, 0);
             ^
>> drivers/input/touchscreen/goodix.c:255:9: error: implicit declaration of function 'gpiod_direction_input' [-Werror=implicit-function-declaration]
     return gpiod_direction_input(ts->gpiod_int);
            ^
   drivers/input/touchscreen/goodix.c: In function 'goodix_get_gpio_config':
>> drivers/input/touchscreen/goodix.c:304:10: error: implicit declaration of function 'devm_gpiod_get' [-Werror=implicit-function-declaration]
     gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
             ^
>> drivers/input/touchscreen/goodix.c:304:52: error: 'GPIOD_IN' undeclared (first use in this function)
     gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
                                                       ^
   drivers/input/touchscreen/goodix.c:304:52: note: each undeclared identifier is reported only once for each function it appears in
   cc1: some warnings being treated as errors

vim +/gpiod_direction_output +250 drivers/input/touchscreen/goodix.c

   244	}
   245	
   246	static int goodix_int_sync(struct goodix_ts_data *ts)
   247	{
   248		int error;
   249	
 > 250		error = gpiod_direction_output(ts->gpiod_int, 0);
   251		if (error)
   252			return error;
   253		msleep(50);				/* T5: 50ms */
   254	
 > 255		return gpiod_direction_input(ts->gpiod_int);
   256	}
   257	
   258	/**
   259	 * goodix_reset - Reset device during power on
   260	 *
   261	 * @ts: goodix_ts_data pointer
   262	 */
   263	static int goodix_reset(struct goodix_ts_data *ts)
   264	{
   265		int error;
   266	
   267		/* begin select I2C slave addr */
   268		error = gpiod_direction_output(ts->gpiod_rst, 0);
   269		if (error)
   270			return error;
   271		msleep(20);				/* T2: > 10ms */
   272		/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
   273		error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
   274		if (error)
   275			return error;
   276		usleep_range(100, 2000);		/* T3: > 100us */
   277		error = gpiod_direction_output(ts->gpiod_rst, 1);
   278		if (error)
   279			return error;
   280		usleep_range(6000, 10000);		/* T4: > 5ms */
   281		/* end select I2C slave addr */
   282		error = gpiod_direction_input(ts->gpiod_rst);
   283		if (error)
   284			return error;
   285		return goodix_int_sync(ts);
   286	}
   287	
   288	/**
   289	 * goodix_get_gpio_config - Get GPIO config from ACPI/DT
   290	 *
   291	 * @ts: goodix_ts_data pointer
   292	 */
   293	static int goodix_get_gpio_config(struct goodix_ts_data *ts)
   294	{
   295		int error;
   296		struct device *dev;
   297		struct gpio_desc *gpiod;
   298	
   299		if (!ts->client)
   300			return -EINVAL;
   301		dev = &ts->client->dev;
   302	
   303		/* Get the interrupt GPIO pin number */
 > 304		gpiod = devm_gpiod_get(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
   305		if (IS_ERR(gpiod)) {
   306			error = PTR_ERR(gpiod);
   307			if (error != -EPROBE_DEFER)

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/octet-stream, Size: 25511 bytes --]