* PROBLEM: (2.6.0) uhci-hcd.c: 9400: host controller process error.
@ 2003-07-23 20:06 Vojtěch Pithart
0 siblings, 0 replies; only message in thread
From: Vojtěch Pithart @ 2003-07-23 20:06 UTC (permalink / raw)
To: linux-kernel
1. My kernel prints out errors to syslog and khubd[5] exits when connecting
USB camera.
2. After connection my USB camera (vend/prod 0x4a9/0x3058), usually used with
gphoto2, the usual message like "new USB device 00:07.2-2, assigned address
3" does appears in syslog. Then the hotplug should be started, but instead
look at this:
....
Jul 23 21:01:03 e ntpdate[6059]: adjust time server 195.113.144.201 offset
0.246202 sec
Jul 23 21:30:38 e kernel: hub 1-0:0: debounce: port 2: delay 100ms stable 4
status 0x101
Jul 23 21:30:38 e kernel: hub 1-0:0: new USB device on port 2, assigned
address 2
čec 23 21:35:26 e su(pam_unix)[6214]: session opened for user root by
vojta(uid=3579)
Jul 23 21:35:30 e kernel: drivers/usb/host/uhci-hcd.c: 9400: host controller
process error. something bad happened
Jul 23 21:35:30 e kernel: drivers/usb/host/uhci-hcd.c: 9400: host controller
halted. very bad
Jul 23 21:35:30 e kernel: drivers/usb/core/message.c: usb_control/bulk_msg:
timeout
Jul 23 21:35:35 e kernel: usb 1-2: USB disconnect, address 2
Jul 23 21:35:47 e kernel: Unable to handle kernel paging request at virtual
address 6b6b6b7b
Jul 23 21:35:47 e kernel: printing eip:
Jul 23 21:35:47 e kernel: c0126c2a
Jul 23 21:35:47 e kernel: *pde = 00000000
Jul 23 21:35:47 e kernel: Oops: 0000 [#1]
Jul 23 21:35:47 e kernel: CPU: 0
Jul 23 21:35:47 e kernel: EIP: 0060:[<c0126c2a>] Not tainted
Jul 23 21:35:47 e kernel: EFLAGS: 00010046
Jul 23 21:35:47 e kernel: EIP is at specific_send_sig_info+0x3a/0x100
Jul 23 21:35:47 e kernel: eax: 00000001 ebx: 6b6b6b6b ecx: 6b6b6b6b edx:
00000000
Jul 23 21:35:47 e kernel: esi: 6b6b6b6b edi: d5d99e9c ebp: 00000000 esp:
d5d99e60
Jul 23 21:35:47 e kernel: ds: 007b es: 007b ss: 0068
Jul 23 21:35:47 e kernel: Process khubd (pid: 5, threadinfo=d5d98000
task=d5f8e040)
Jul 23 21:35:47 e kernel: Stack: 00000202 d5d98000 cb0ac85c c70a9518 c01275a7
6b6b6b6b d5d99e9c 6b6b6b6b
Jul 23 21:35:47 e kernel: cb0ac85c cb0aca14 cb0ac85c c0316dfc 6b6b6b6b
d5d99e9c 6b6b6b6b 0000000d
Jul 23 21:35:47 e kernel: 00000020 fffffffc 6b6b6b6b d256bae0 d256bae0
c016436d d256bae0 c04b0c98
Jul 23 21:35:47 e kernel: Call Trace:
Jul 23 21:35:47 e kernel: [<c01275a7>] send_sig_info+0x27/0x60
Jul 23 21:35:47 e kernel: [<c0316dfc>] usbfs_remove_device+0xcc/0xe9
Jul 23 21:35:47 e kernel: [<c016436d>] dput+0x1d/0x1e0
Jul 23 21:35:47 e kernel: [<c016c40d>] simple_rmdir+0x2d/0x40
Jul 23 21:35:47 e kernel: [<c016436d>] dput+0x1d/0x1e0
Jul 23 21:35:47 e kernel: [<c0181fd2>] sysfs_remove_dir+0x112/0x140
Jul 23 21:35:47 e kernel: [<c024154b>] unlink+0x5b/0x70
Jul 23 21:35:47 e kernel: [<c030fe50>] hcd_endpoint_disable+0x0/0x190
Jul 23 21:35:47 e kernel: [<c030be70>] usb_disconnect+0xf0/0x140
Jul 23 21:35:47 e kernel: [<c030fe50>] hcd_endpoint_disable+0x0/0x190
Jul 23 21:35:47 e kernel: [<c030be8e>] usb_disconnect+0x10e/0x140
Jul 23 21:35:47 e kernel: [<c030e19c>] hub_port_connect_change+0x5c/0x2b0
Jul 23 21:35:47 e kernel: [<c030e537>] hub_events+0x147/0x330
Jul 23 21:35:47 e kernel: [<c011b839>] schedule+0x2b9/0x370
Jul 23 21:35:47 e kernel: [<c030e755>] hub_thread+0x35/0xf0
Jul 23 21:35:47 e kernel: [<c011b950>] default_wake_function+0x0/0x20
Jul 23 21:35:47 e kernel: [<c030e720>] hub_thread+0x0/0xf0
Jul 23 21:35:47 e kernel: [<c01071f9>] kernel_thread_helper+0x5/0xc
Jul 23 21:35:47 e kernel:
Jul 23 21:35:47 e kernel: Code: f6 43 10 01 75 43 8d 4e ff 0f a3 8b b4 05 00
00 19 c0 31 d2
Jul 23 21:35:47 e kernel: <6>note: khubd[5] exited with preempt_count 2
Jul 23 21:35:48 e kernel: Slab corruption: start=d14227e0, expend=d142285f,
problemat=d14227e8
Jul 23 21:35:48 e kernel: Last user: [<c0313f52>](usbdev_release+0xb2/0xc0)
Jul 23 21:35:48 e kernel: Data: ********6A *6C *************00 00 00 00
****************************************************
***********************************************A5
Jul 23 21:35:48 e kernel: Next: 71 F0 2C .52 3F 31 C0 71 F0 2C
.********************
Jul 23 21:35:48 e kernel: slab error in check_poison_obj(): cache `size-128':
object was modified after freeing
Jul 23 21:35:48 e kernel: Call Trace:
Jul 23 21:35:48 e kernel: [<c013c2d9>] check_poison_obj+0x189/0x1a0
Jul 23 21:35:48 e kernel: [<c013d822>] __kmalloc+0xb2/0x170
Jul 23 21:35:48 e kernel: [<c0174b75>] load_elf_interp+0xa5/0x230
Jul 23 21:35:48 e kernel: [<c0141e71>] pte_alloc_map+0x31/0xb0
Jul 23 21:35:48 e kernel: [<c0174b75>] load_elf_interp+0xa5/0x230
Jul 23 21:35:48 e kernel: [<c0159115>] setup_arg_pages+0x165/0x1a0
Jul 23 21:35:48 e kernel: [<c0175587>] load_elf_binary+0x767/0xa00
Jul 23 21:35:48 e kernel: [<c0174e20>] load_elf_binary+0x0/0xa00
Jul 23 21:35:48 e kernel: [<c0159deb>] search_binary_handler+0xbb/0x260
Jul 23 21:35:48 e kernel: [<c015a128>] do_execve+0x198/0x220
Jul 23 21:35:48 e kernel: [<c015b71d>] getname+0x5d/0xa0
Jul 23 21:35:48 e kernel: [<c01079bd>] sys_execve+0x2d/0x60
Jul 23 21:35:48 e kernel: [<c0108f8f>] syscall_call+0x7/0xb
Jul 23 21:35:48 e kernel:
(END)
4. Kernel version Linux version 2.6.0-test1 (root@e) (gcc version 2.96
20000731 (Red Hat Linux 7.3 2.96-110)) #6 Wed Jul 23 09:57:36 CEST 2003
7. 1. 21:49:28(root@e)/usr/src/linux-2.6.0-test1#sh scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux e 2.6.0-test1 #6 Wed Jul 23 09:57:36 CEST 2003 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
module-init-tools 2.4.25
e2fsprogs 1.27
reiserfsprogs 3.x.0j
pcmcia-cs 3.1.22
quota-tools 3.01.
PPP 2.4.1
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 3.1.4
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0.11
Modules Loaded
7.2. 22:00:31(vojta@e)~#cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 7
model name : AMD Duron(tm) processor
stepping : 0
cpu MHz : 1000.178
cache size : 64 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 1961.98
7.3.
22:01:40(vojta@e)~#cat /proc/modules
22:02:06(vojta@e)~#lsmod
Module Size Used by
22:02:13(vojta@e)~#
(no modules loaded; but module loading _is_ currently functional)
7.4.
22:02:13(vojta@e)~#cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0278-027a : parport0
027b-027f : parport0
02f8-02ff : serial
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0cf8-0cff : PCI conf1
5000-500f : VIA Technologies, In VT82C686 [Apollo Sup
6000-607f : VIA Technologies, In VT82C686 [Apollo Sup
9000-900f : VIA Technologies, In VT82C586/B/686A/B PI
9000-9007 : ide0
9008-900f : ide1
9400-941f : VIA Technologies, In USB
9400-941f : uhci-hcd
9800-981f : VIA Technologies, In USB (#2)
9800-981f : uhci-hcd
9c00-9cff : VIA Technologies, In VT82C686 AC97 Audio
9c00-9cff : VIA686A
a000-a003 : VIA Technologies, In VT82C686 AC97 Audio
a400-a403 : VIA Technologies, In VT82C686 AC97 Audio
a400-a401 : VIA82xx MPU401
ac00-ac7f : Avance Logic Inc. ALS4000 Audio Chipse
ac00-ac3f : ALS4000
b000-b07f : 3Com Corporation 3c900B-Combo [Etherl
b400-b41f : Realtek Semiconducto RTL-8029(AS)
b400-b41f : ne2k-pci
b800-b807 : Promise Technology, 20265
bc00-bc03 : Promise Technology, 20265
c000-c007 : Promise Technology, 20265
c000-c007 : ide3
c400-c403 : Promise Technology, 20265
c402-c402 : ide3
c800-c83f : Promise Technology, 20265
c800-c807 : ide2
c808-c80f : ide3
c810-c83f : PDC20265
22:03:00(vojta@e)~#cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-15feffff : System RAM
00100000-004197b0 : Kernel code
004197b1-0054d87f : Kernel data
15ff0000-15ff2fff : ACPI Non-volatile Storage
15ff3000-15ffffff : ACPI Tables
d0000000-d3ffffff : VIA Technologies, In VT8363/8365 [KT133/K
d4000000-d7ffffff : S3 Inc. ViRGE/DX or /GX
d8000000-d8ffffff : PCI Bus #01
d8000000-d8ffffff : nVidia Corporation NV4 [Riva TnT]
d9000000-daffffff : PCI Bus #01
d9000000-d9ffffff : nVidia Corporation NV4 [Riva TnT]
dc000000-dc01ffff : Promise Technology, 20265
dc020000-dc020fff : Harris Semiconductor Prism 2.5 Wavelan ch
dc021000-dc02107f : 3Com Corporation 3c900B-Combo [Etherl
ffff0000-ffffffff : reserved
7.5. PCI bus
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d9000000-daffffff
Prefetchable memory behind bridge: d8000000-d8ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev
40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 9000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 9400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 16) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 9800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97
Audio Controller (rev 50)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 3300
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at 9c00 [size=256]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at a400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01) (prog-if
00 [VGA])
Subsystem: S3 Inc. ViRGE/DX
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [disabled] [size=64M]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:09.0 Multimedia audio controller: Avance Logic Inc. ALS4000 Audio Chipset
Subsystem: Avance Logic Inc. ALS4000 Audio Chipset
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ac00 [size=128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Ethernet controller: 3Com Corporation 3c900B-Combo [Etherlink XL
Combo] (rev 04)
Subsystem: 3Com Corporation 3C900B-Combo Etherlink XL Combo
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 12000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b000 [size=128]
Region 1: Memory at dc021000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:0c.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset
(rev 01)
Subsystem: Harris Semiconductor Prism 2.5 Wavelan chipset
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at dc020000 (32-bit, prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b400 [size=32]
Expansion ROM at <unassigned> [disabled] [size=32K]
00:0f.0 RAID bus controller: Promise Technology, Inc. 20265 (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=64]
Region 5: Memory at dc000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV4 [RIVA TNT] (rev 04)
(prog-if 00 [VGA])
Subsystem: STB Systems Inc Velocity 4400
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 1.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
7.6.
[root@e root]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: MITSUMI Model: CR-2801TE Rev: 1.10
Type: CD-ROM ANSI SCSI revision: 02
(Emulated CD burner)
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2003-07-23 19:51 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-07-23 20:06 PROBLEM: (2.6.0) uhci-hcd.c: 9400: host controller process error Vojtěch Pithart
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.