* [PATCH 00/23] Series short description
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap
Hi all,
Looks like stg mail choked on a bad email addres, here's a retry.
These patches are against what I have sitting in omap-for-linus
branch in the linux-omap tree.
Regards,
Tony
---
Enric Balletbo i Serra (8):
omap3: Add platform data for the twl4030_codec MFD on IGEP v2
omap3: Fix typo on IGEP v2 board
omap3: Add platform init code for EHCI driver on IGEP v2
omap3: Enable DSS2 for IGEP v2 board
omap3: Add support for flash on IGEP v2 board
ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM
omap3: Use timing data for omap2_init_common_hw on IGEP v2
omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures
Grazvydas Ignotas (3):
OMAP: pandora: add DSS2 support and related regulators
omap3: pandora: update regulator setup
omap3: pandora: update defconfig
Jonas Zetterberg (2):
IGEPv2: Added WIFI support
IGEPv2: Use Red Led1 as Heartbeat if configured
Sanjeev Premi (4):
omap3evm: Add mux settings for keypad
omap3evm: Fixes after moving to matrix_keypad
omap3evm: Configure GPIO175 for touchscreen PEN_IRQ
OMAP3EVM: PM: Update defconfig
Thomas Weber (2):
Add minimal support for DevKit8000
Add devkit8000_defconfig
Vaibhav Hiremath (3):
AM3517: Enable basic I2C Support
AM3517: Enable RTC driver support for AM3517EVM
AM3517: Enable I2C-GPIO Expander driver support for AM3517EVM
vikram pandita (1):
omap: zoom3: enable ehci support
arch/arm/configs/devkit8000_defconfig | 1889 ++++++++++++++++++++++++
arch/arm/configs/igep0020_defconfig | 525 ++++---
arch/arm/configs/omap3_evm_defconfig | 6
arch/arm/configs/omap3_pandora_defconfig | 678 +++++++--
arch/arm/mach-omap2/Kconfig | 6
arch/arm/mach-omap2/Makefile | 2
arch/arm/mach-omap2/board-am3517evm.c | 86 +
arch/arm/mach-omap2/board-devkit8000.c | 691 +++++++++
arch/arm/mach-omap2/board-igep0020.c | 269 +++
arch/arm/mach-omap2/board-omap3evm.c | 33
arch/arm/mach-omap2/board-omap3pandora.c | 180 ++
arch/arm/mach-omap2/board-zoom3.c | 14
arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h | 51 +
13 files changed, 4020 insertions(+), 410 deletions(-)
create mode 100644 arch/arm/configs/devkit8000_defconfig
create mode 100644 arch/arm/mach-omap2/board-devkit8000.c
create mode 100644 arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
--
Signature
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH 00/23] Series short description
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel
Hi all,
Looks like stg mail choked on a bad email addres, here's a retry.
These patches are against what I have sitting in omap-for-linus
branch in the linux-omap tree.
Regards,
Tony
---
Enric Balletbo i Serra (8):
omap3: Add platform data for the twl4030_codec MFD on IGEP v2
omap3: Fix typo on IGEP v2 board
omap3: Add platform init code for EHCI driver on IGEP v2
omap3: Enable DSS2 for IGEP v2 board
omap3: Add support for flash on IGEP v2 board
ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM
omap3: Use timing data for omap2_init_common_hw on IGEP v2
omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures
Grazvydas Ignotas (3):
OMAP: pandora: add DSS2 support and related regulators
omap3: pandora: update regulator setup
omap3: pandora: update defconfig
Jonas Zetterberg (2):
IGEPv2: Added WIFI support
IGEPv2: Use Red Led1 as Heartbeat if configured
Sanjeev Premi (4):
omap3evm: Add mux settings for keypad
omap3evm: Fixes after moving to matrix_keypad
omap3evm: Configure GPIO175 for touchscreen PEN_IRQ
OMAP3EVM: PM: Update defconfig
Thomas Weber (2):
Add minimal support for DevKit8000
Add devkit8000_defconfig
Vaibhav Hiremath (3):
AM3517: Enable basic I2C Support
AM3517: Enable RTC driver support for AM3517EVM
AM3517: Enable I2C-GPIO Expander driver support for AM3517EVM
vikram pandita (1):
omap: zoom3: enable ehci support
arch/arm/configs/devkit8000_defconfig | 1889 ++++++++++++++++++++++++
arch/arm/configs/igep0020_defconfig | 525 ++++---
arch/arm/configs/omap3_evm_defconfig | 6
arch/arm/configs/omap3_pandora_defconfig | 678 +++++++--
arch/arm/mach-omap2/Kconfig | 6
arch/arm/mach-omap2/Makefile | 2
arch/arm/mach-omap2/board-am3517evm.c | 86 +
arch/arm/mach-omap2/board-devkit8000.c | 691 +++++++++
arch/arm/mach-omap2/board-igep0020.c | 269 +++
arch/arm/mach-omap2/board-omap3evm.c | 33
arch/arm/mach-omap2/board-omap3pandora.c | 180 ++
arch/arm/mach-omap2/board-zoom3.c | 14
arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h | 51 +
13 files changed, 4020 insertions(+), 410 deletions(-)
create mode 100644 arch/arm/configs/devkit8000_defconfig
create mode 100644 arch/arm/mach-omap2/board-devkit8000.c
create mode 100644 arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
--
Signature
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH 01/23] omap: zoom3: enable ehci support
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:31 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Vikram Pandita, linux-omap, Anand Gadiyar
From: vikram pandita <vikram.pandita@ti.com>
Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-zoom3.c | 14 ++++++++++++++
1 files changed, 14 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c
index 5e20894..d3e3cd5 100644
--- a/arch/arm/mach-omap2/board-zoom3.c
+++ b/arch/arm/mach-omap2/board-zoom3.c
@@ -20,6 +20,7 @@
#include <plat/common.h>
#include <plat/board.h>
+#include <plat/usb.h>
#include "mux.h"
#include "sdram-hynix-h8mbx00u0mer-0em.h"
@@ -51,11 +52,24 @@ static struct omap_board_mux board_mux[] __initdata = {
#define board_mux NULL
#endif
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 64,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
static void __init omap_zoom_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
zoom_peripherals_init();
zoom_debugboard_init();
+
+ omap_mux_init_gpio(64, OMAP_PIN_OUTPUT);
+ usb_ehci_init(&ehci_pdata);
}
MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 01/23] omap: zoom3: enable ehci support
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel
From: vikram pandita <vikram.pandita@ti.com>
Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-zoom3.c | 14 ++++++++++++++
1 files changed, 14 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c
index 5e20894..d3e3cd5 100644
--- a/arch/arm/mach-omap2/board-zoom3.c
+++ b/arch/arm/mach-omap2/board-zoom3.c
@@ -20,6 +20,7 @@
#include <plat/common.h>
#include <plat/board.h>
+#include <plat/usb.h>
#include "mux.h"
#include "sdram-hynix-h8mbx00u0mer-0em.h"
@@ -51,11 +52,24 @@ static struct omap_board_mux board_mux[] __initdata = {
#define board_mux NULL
#endif
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 64,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
static void __init omap_zoom_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
zoom_peripherals_init();
zoom_debugboard_init();
+
+ omap_mux_init_gpio(64, OMAP_PIN_OUTPUT);
+ usb_ehci_init(&ehci_pdata);
}
MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 02/23] omap3evm: Add mux settings for keypad
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:31 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Sanjeev Premi
From: Sanjeev Premi <premi@ti.com>
This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 4 ++++
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 45227f3..3b473cf 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -647,6 +647,10 @@ static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP |
+ OMAP_PIN_OFF_WAKEUPENABLE),
+
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 02/23] omap3evm: Add mux settings for keypad
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Sanjeev Premi <premi@ti.com>
This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 4 ++++
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 45227f3..3b473cf 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -647,6 +647,10 @@ static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP |
+ OMAP_PIN_OFF_WAKEUPENABLE),
+
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 03/23] omap3evm: Fixes after moving to matrix_keypad
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:31 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Sanjeev Premi
From: Sanjeev Premi <premi@ti.com>
The keypad was not working properly after migrating
to matrix_keypad.
Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 27 +++++++++++++++------------
1 files changed, 15 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 3b473cf..34655a6 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -448,20 +448,23 @@ static struct twl4030_usb_data omap3evm_usb_data = {
static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_RIGHT),
- KEY(0, 2, KEY_A),
- KEY(0, 3, KEY_B),
- KEY(1, 0, KEY_DOWN),
+ KEY(0, 1, KEY_DOWN),
+ KEY(0, 2, KEY_ENTER),
+ KEY(0, 3, KEY_M),
+
+ KEY(1, 0, KEY_RIGHT),
KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_E),
- KEY(1, 3, KEY_F),
- KEY(2, 0, KEY_ENTER),
- KEY(2, 1, KEY_I),
+ KEY(1, 2, KEY_I),
+ KEY(1, 3, KEY_N),
+
+ KEY(2, 0, KEY_A),
+ KEY(2, 1, KEY_E),
KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_K),
- KEY(3, 0, KEY_M),
- KEY(3, 1, KEY_N),
- KEY(3, 2, KEY_O),
+ KEY(2, 3, KEY_O),
+
+ KEY(3, 0, KEY_B),
+ KEY(3, 1, KEY_F),
+ KEY(3, 2, KEY_K),
KEY(3, 3, KEY_P)
};
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 03/23] omap3evm: Fixes after moving to matrix_keypad
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Sanjeev Premi <premi@ti.com>
The keypad was not working properly after migrating
to matrix_keypad.
Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 27 +++++++++++++++------------
1 files changed, 15 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 3b473cf..34655a6 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -448,20 +448,23 @@ static struct twl4030_usb_data omap3evm_usb_data = {
static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
- KEY(0, 1, KEY_RIGHT),
- KEY(0, 2, KEY_A),
- KEY(0, 3, KEY_B),
- KEY(1, 0, KEY_DOWN),
+ KEY(0, 1, KEY_DOWN),
+ KEY(0, 2, KEY_ENTER),
+ KEY(0, 3, KEY_M),
+
+ KEY(1, 0, KEY_RIGHT),
KEY(1, 1, KEY_UP),
- KEY(1, 2, KEY_E),
- KEY(1, 3, KEY_F),
- KEY(2, 0, KEY_ENTER),
- KEY(2, 1, KEY_I),
+ KEY(1, 2, KEY_I),
+ KEY(1, 3, KEY_N),
+
+ KEY(2, 0, KEY_A),
+ KEY(2, 1, KEY_E),
KEY(2, 2, KEY_J),
- KEY(2, 3, KEY_K),
- KEY(3, 0, KEY_M),
- KEY(3, 1, KEY_N),
- KEY(3, 2, KEY_O),
+ KEY(2, 3, KEY_O),
+
+ KEY(3, 0, KEY_B),
+ KEY(3, 1, KEY_F),
+ KEY(3, 2, KEY_K),
KEY(3, 3, KEY_P)
};
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 04/23] omap3evm: Configure GPIO175 for touchscreen PEN_IRQ
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:31 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Sanjeev Premi
From: Sanjeev Premi <premi@ti.com>
GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 4 +++-
1 files changed, 3 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 34655a6..fa1f9d5 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -653,7 +653,9 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_INPUT_PULLUP |
OMAP_PIN_OFF_WAKEUPENABLE),
-
+ OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP |
+ OMAP_PIN_OFF_WAKEUPENABLE),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 04/23] omap3evm: Configure GPIO175 for touchscreen PEN_IRQ
@ 2010-02-18 1:31 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Sanjeev Premi <premi@ti.com>
GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3evm.c | 4 +++-
1 files changed, 3 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 34655a6..fa1f9d5 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -653,7 +653,9 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
OMAP_PIN_OFF_INPUT_PULLUP |
OMAP_PIN_OFF_WAKEUPENABLE),
-
+ OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
+ OMAP_PIN_OFF_INPUT_PULLUP |
+ OMAP_PIN_OFF_WAKEUPENABLE),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 05/23] OMAP: pandora: add DSS2 support and related regulators
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Tomi Valkeinen, linux-omap, Grazvydas Ignotas
From: Grazvydas Ignotas <notasas@gmail.com>
This patch adds configuration data for DSS2 and sets up
display related regulators.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 111 ++++++++++++++++++++++++++++++
1 files changed, 111 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 9967b5d..7ea3894 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -40,6 +40,7 @@
#include <mach/hardware.h>
#include <plat/mcspi.h>
#include <plat/usb.h>
+#include <plat/display.h>
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
@@ -192,6 +193,61 @@ static struct twl4030_keypad_data pandora_kp_data = {
.rep = 1,
};
+static struct omap_dss_device pandora_lcd_device = {
+ .name = "lcd",
+ .driver_name = "tpo_td043mtea1_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .reset_gpio = 157,
+};
+
+static struct omap_dss_device pandora_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+};
+
+static struct omap_dss_device *pandora_dss_devices[] = {
+ &pandora_lcd_device,
+ &pandora_tv_device,
+};
+
+static struct omap_dss_board_info pandora_dss_data = {
+ .num_devices = ARRAY_SIZE(pandora_dss_devices),
+ .devices = pandora_dss_devices,
+ .default_device = &pandora_lcd_device,
+};
+
+static struct platform_device pandora_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &pandora_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply pandora_vcc_lcd_supply = {
+ .supply = "vcc",
+ .dev = &pandora_lcd_device.dev,
+};
+
+static struct regulator_consumer_supply pandora_vdda_dac_supply = {
+ .supply = "vdda_dac",
+ .dev = &pandora_dss_device.dev,
+};
+
+static struct regulator_consumer_supply pandora_vdds_supplies[] = {
+ {
+ .supply = "vdds_sdi",
+ .dev = &pandora_dss_device.dev,
+ },
+ {
+ .supply = "vdds_dsi",
+ .dev = &pandora_dss_device.dev,
+ },
+};
+
static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{
.mmc = 1,
@@ -277,6 +333,51 @@ static struct regulator_init_data pandora_vmmc2 = {
.consumer_supplies = &pandora_vmmc2_supply,
};
+/* VDAC for DSS driving S-Video */
+static struct regulator_init_data pandora_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_vdda_dac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data pandora_vpll2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(pandora_vdds_supplies),
+ .consumer_supplies = pandora_vdds_supplies,
+};
+
+/* VAUX1 for LCD */
+static struct regulator_init_data pandora_vaux1 = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_vcc_lcd_supply,
+};
+
static struct twl4030_usb_data omap3pandora_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -298,6 +399,9 @@ static struct twl4030_platform_data omap3pandora_twldata = {
.codec = &omap3pandora_codec_data,
.vmmc1 = &pandora_vmmc1,
.vmmc2 = &pandora_vmmc2,
+ .vdac = &pandora_vdac,
+ .vpll2 = &pandora_vpll2,
+ .vaux1 = &pandora_vaux1,
.keypad = &pandora_kp_data,
};
@@ -365,6 +469,12 @@ static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_PANDORA_TS_GPIO),
.platform_data = &ads7846_config,
+ }, {
+ .modalias = "tpo_td043mtea1_panel_spi",
+ .bus_num = 1,
+ .chip_select = 1,
+ .max_speed_hz = 375000,
+ .platform_data = &pandora_lcd_device,
}
};
@@ -379,6 +489,7 @@ static void __init omap3pandora_init_irq(void)
static struct platform_device *omap3pandora_devices[] __initdata = {
&pandora_leds_gpio,
&pandora_keys_gpio,
+ &pandora_dss_device,
};
static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 05/23] OMAP: pandora: add DSS2 support and related regulators
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Grazvydas Ignotas <notasas@gmail.com>
This patch adds configuration data for DSS2 and sets up
display related regulators.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 111 ++++++++++++++++++++++++++++++
1 files changed, 111 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 9967b5d..7ea3894 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -40,6 +40,7 @@
#include <mach/hardware.h>
#include <plat/mcspi.h>
#include <plat/usb.h>
+#include <plat/display.h>
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
@@ -192,6 +193,61 @@ static struct twl4030_keypad_data pandora_kp_data = {
.rep = 1,
};
+static struct omap_dss_device pandora_lcd_device = {
+ .name = "lcd",
+ .driver_name = "tpo_td043mtea1_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .reset_gpio = 157,
+};
+
+static struct omap_dss_device pandora_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+};
+
+static struct omap_dss_device *pandora_dss_devices[] = {
+ &pandora_lcd_device,
+ &pandora_tv_device,
+};
+
+static struct omap_dss_board_info pandora_dss_data = {
+ .num_devices = ARRAY_SIZE(pandora_dss_devices),
+ .devices = pandora_dss_devices,
+ .default_device = &pandora_lcd_device,
+};
+
+static struct platform_device pandora_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &pandora_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply pandora_vcc_lcd_supply = {
+ .supply = "vcc",
+ .dev = &pandora_lcd_device.dev,
+};
+
+static struct regulator_consumer_supply pandora_vdda_dac_supply = {
+ .supply = "vdda_dac",
+ .dev = &pandora_dss_device.dev,
+};
+
+static struct regulator_consumer_supply pandora_vdds_supplies[] = {
+ {
+ .supply = "vdds_sdi",
+ .dev = &pandora_dss_device.dev,
+ },
+ {
+ .supply = "vdds_dsi",
+ .dev = &pandora_dss_device.dev,
+ },
+};
+
static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{
.mmc = 1,
@@ -277,6 +333,51 @@ static struct regulator_init_data pandora_vmmc2 = {
.consumer_supplies = &pandora_vmmc2_supply,
};
+/* VDAC for DSS driving S-Video */
+static struct regulator_init_data pandora_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_vdda_dac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data pandora_vpll2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(pandora_vdds_supplies),
+ .consumer_supplies = pandora_vdds_supplies,
+};
+
+/* VAUX1 for LCD */
+static struct regulator_init_data pandora_vaux1 = {
+ .constraints = {
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_vcc_lcd_supply,
+};
+
static struct twl4030_usb_data omap3pandora_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -298,6 +399,9 @@ static struct twl4030_platform_data omap3pandora_twldata = {
.codec = &omap3pandora_codec_data,
.vmmc1 = &pandora_vmmc1,
.vmmc2 = &pandora_vmmc2,
+ .vdac = &pandora_vdac,
+ .vpll2 = &pandora_vpll2,
+ .vaux1 = &pandora_vaux1,
.keypad = &pandora_kp_data,
};
@@ -365,6 +469,12 @@ static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_PANDORA_TS_GPIO),
.platform_data = &ads7846_config,
+ }, {
+ .modalias = "tpo_td043mtea1_panel_spi",
+ .bus_num = 1,
+ .chip_select = 1,
+ .max_speed_hz = 375000,
+ .platform_data = &pandora_lcd_device,
}
};
@@ -379,6 +489,7 @@ static void __init omap3pandora_init_irq(void)
static struct platform_device *omap3pandora_devices[] __initdata = {
&pandora_leds_gpio,
&pandora_keys_gpio,
+ &pandora_dss_device,
};
static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 06/23] omap3: pandora: update regulator setup
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Grazvydas Ignotas
From: Grazvydas Ignotas <notasas@gmail.com>
Update pandora's regulator setup:
- add new regulators: VAUX2, VAUX4 and VSIM
- add new consumers: ads7846, nub controllers, USB PHY, audio DAC
- use dev names instead of struct device pointers
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 111 +++++++++++++++++++++---------
1 files changed, 78 insertions(+), 33 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 7ea3894..a0acf8d 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -227,27 +227,6 @@ static struct platform_device pandora_dss_device = {
},
};
-static struct regulator_consumer_supply pandora_vcc_lcd_supply = {
- .supply = "vcc",
- .dev = &pandora_lcd_device.dev,
-};
-
-static struct regulator_consumer_supply pandora_vdda_dac_supply = {
- .supply = "vdda_dac",
- .dev = &pandora_dss_device.dev,
-};
-
-static struct regulator_consumer_supply pandora_vdds_supplies[] = {
- {
- .supply = "vdds_sdi",
- .dev = &pandora_dss_device.dev,
- },
- {
- .supply = "vdds_dsi",
- .dev = &pandora_dss_device.dev,
- },
-};
-
static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{
.mmc = 1,
@@ -273,14 +252,6 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{} /* Terminator */
};
-static struct regulator_consumer_supply pandora_vmmc1_supply = {
- .supply = "vmmc",
-};
-
-static struct regulator_consumer_supply pandora_vmmc2_supply = {
- .supply = "vmmc",
-};
-
static int omap3pandora_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -289,10 +260,6 @@ static int omap3pandora_twl_gpio_setup(struct device *dev,
omap3pandora_mmc[1].gpio_cd = gpio + 1;
omap2_hsmmc_init(omap3pandora_mmc);
- /* link regulators to MMC adapters */
- pandora_vmmc1_supply.dev = omap3pandora_mmc[0].dev;
- pandora_vmmc2_supply.dev = omap3pandora_mmc[1].dev;
-
return 0;
}
@@ -303,6 +270,36 @@ static struct twl4030_gpio_platform_data omap3pandora_gpio_data = {
.setup = omap3pandora_twl_gpio_setup,
};
+static struct regulator_consumer_supply pandora_vmmc1_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
+
+static struct regulator_consumer_supply pandora_vmmc2_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.1");
+
+static struct regulator_consumer_supply pandora_vdda_dac_supply =
+ REGULATOR_SUPPLY("vdda_dac", "omapdss");
+
+static struct regulator_consumer_supply pandora_vdds_supplies[] = {
+ REGULATOR_SUPPLY("vdds_sdi", "omapdss"),
+ REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
+};
+
+static struct regulator_consumer_supply pandora_vcc_lcd_supply =
+ REGULATOR_SUPPLY("vcc", "display0");
+
+static struct regulator_consumer_supply pandora_usb_phy_supply =
+ REGULATOR_SUPPLY("hsusb0", "ehci-omap.0");
+
+/* ads7846 on SPI and 2 nub controllers on I2C */
+static struct regulator_consumer_supply pandora_vaux4_supplies[] = {
+ REGULATOR_SUPPLY("vcc", "spi1.0"),
+ REGULATOR_SUPPLY("vcc", "3-0066"),
+ REGULATOR_SUPPLY("vcc", "3-0067"),
+};
+
+static struct regulator_consumer_supply pandora_adac_supply =
+ REGULATOR_SUPPLY("vcc", "soc-audio");
+
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data pandora_vmmc1 = {
.constraints = {
@@ -378,6 +375,51 @@ static struct regulator_init_data pandora_vaux1 = {
.consumer_supplies = &pandora_vcc_lcd_supply,
};
+/* VAUX2 for USB host PHY */
+static struct regulator_init_data pandora_vaux2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_usb_phy_supply,
+};
+
+/* VAUX4 for ads7846 and nubs */
+static struct regulator_init_data pandora_vaux4 = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(pandora_vaux4_supplies),
+ .consumer_supplies = pandora_vaux4_supplies,
+};
+
+/* VSIM for audio DAC */
+static struct regulator_init_data pandora_vsim = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_adac_supply,
+};
+
static struct twl4030_usb_data omap3pandora_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -402,6 +444,9 @@ static struct twl4030_platform_data omap3pandora_twldata = {
.vdac = &pandora_vdac,
.vpll2 = &pandora_vpll2,
.vaux1 = &pandora_vaux1,
+ .vaux2 = &pandora_vaux2,
+ .vaux4 = &pandora_vaux4,
+ .vsim = &pandora_vsim,
.keypad = &pandora_kp_data,
};
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 06/23] omap3: pandora: update regulator setup
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Grazvydas Ignotas <notasas@gmail.com>
Update pandora's regulator setup:
- add new regulators: VAUX2, VAUX4 and VSIM
- add new consumers: ads7846, nub controllers, USB PHY, audio DAC
- use dev names instead of struct device pointers
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 111 +++++++++++++++++++++---------
1 files changed, 78 insertions(+), 33 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 7ea3894..a0acf8d 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -227,27 +227,6 @@ static struct platform_device pandora_dss_device = {
},
};
-static struct regulator_consumer_supply pandora_vcc_lcd_supply = {
- .supply = "vcc",
- .dev = &pandora_lcd_device.dev,
-};
-
-static struct regulator_consumer_supply pandora_vdda_dac_supply = {
- .supply = "vdda_dac",
- .dev = &pandora_dss_device.dev,
-};
-
-static struct regulator_consumer_supply pandora_vdds_supplies[] = {
- {
- .supply = "vdds_sdi",
- .dev = &pandora_dss_device.dev,
- },
- {
- .supply = "vdds_dsi",
- .dev = &pandora_dss_device.dev,
- },
-};
-
static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{
.mmc = 1,
@@ -273,14 +252,6 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
{} /* Terminator */
};
-static struct regulator_consumer_supply pandora_vmmc1_supply = {
- .supply = "vmmc",
-};
-
-static struct regulator_consumer_supply pandora_vmmc2_supply = {
- .supply = "vmmc",
-};
-
static int omap3pandora_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -289,10 +260,6 @@ static int omap3pandora_twl_gpio_setup(struct device *dev,
omap3pandora_mmc[1].gpio_cd = gpio + 1;
omap2_hsmmc_init(omap3pandora_mmc);
- /* link regulators to MMC adapters */
- pandora_vmmc1_supply.dev = omap3pandora_mmc[0].dev;
- pandora_vmmc2_supply.dev = omap3pandora_mmc[1].dev;
-
return 0;
}
@@ -303,6 +270,36 @@ static struct twl4030_gpio_platform_data omap3pandora_gpio_data = {
.setup = omap3pandora_twl_gpio_setup,
};
+static struct regulator_consumer_supply pandora_vmmc1_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
+
+static struct regulator_consumer_supply pandora_vmmc2_supply =
+ REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.1");
+
+static struct regulator_consumer_supply pandora_vdda_dac_supply =
+ REGULATOR_SUPPLY("vdda_dac", "omapdss");
+
+static struct regulator_consumer_supply pandora_vdds_supplies[] = {
+ REGULATOR_SUPPLY("vdds_sdi", "omapdss"),
+ REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
+};
+
+static struct regulator_consumer_supply pandora_vcc_lcd_supply =
+ REGULATOR_SUPPLY("vcc", "display0");
+
+static struct regulator_consumer_supply pandora_usb_phy_supply =
+ REGULATOR_SUPPLY("hsusb0", "ehci-omap.0");
+
+/* ads7846 on SPI and 2 nub controllers on I2C */
+static struct regulator_consumer_supply pandora_vaux4_supplies[] = {
+ REGULATOR_SUPPLY("vcc", "spi1.0"),
+ REGULATOR_SUPPLY("vcc", "3-0066"),
+ REGULATOR_SUPPLY("vcc", "3-0067"),
+};
+
+static struct regulator_consumer_supply pandora_adac_supply =
+ REGULATOR_SUPPLY("vcc", "soc-audio");
+
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data pandora_vmmc1 = {
.constraints = {
@@ -378,6 +375,51 @@ static struct regulator_init_data pandora_vaux1 = {
.consumer_supplies = &pandora_vcc_lcd_supply,
};
+/* VAUX2 for USB host PHY */
+static struct regulator_init_data pandora_vaux2 = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_usb_phy_supply,
+};
+
+/* VAUX4 for ads7846 and nubs */
+static struct regulator_init_data pandora_vaux4 = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(pandora_vaux4_supplies),
+ .consumer_supplies = pandora_vaux4_supplies,
+};
+
+/* VSIM for audio DAC */
+static struct regulator_init_data pandora_vsim = {
+ .constraints = {
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &pandora_adac_supply,
+};
+
static struct twl4030_usb_data omap3pandora_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -402,6 +444,9 @@ static struct twl4030_platform_data omap3pandora_twldata = {
.vdac = &pandora_vdac,
.vpll2 = &pandora_vpll2,
.vaux1 = &pandora_vaux1,
+ .vaux2 = &pandora_vaux2,
+ .vaux4 = &pandora_vaux4,
+ .vsim = &pandora_vsim,
.keypad = &pandora_kp_data,
};
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 07/23] omap3: pandora: update defconfig
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Grazvydas Ignotas
From: Grazvydas Ignotas <notasas@gmail.com>
Enable DSS2 and update defconfig for current kernel.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/omap3_pandora_defconfig | 678 +++++++++++++++++++++++-------
1 files changed, 513 insertions(+), 165 deletions(-)
diff --git a/arch/arm/configs/omap3_pandora_defconfig b/arch/arm/configs/omap3_pandora_defconfig
index f74eb9a..5d08e0b 100644
--- a/arch/arm/configs/omap3_pandora_defconfig
+++ b/arch/arm/configs/omap3_pandora_defconfig
@@ -1,15 +1,14 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc7
-# Fri Dec 5 11:54:09 2008
+# Linux kernel version: 2.6.33-rc6
+# Sat Feb 6 20:25:41 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
+CONFIG_HAVE_PROC_CPU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,13 +17,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
@@ -32,8 +31,15 @@ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
@@ -42,24 +48,33 @@ CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
-# CONFIG_SYSFS_DEPRECATED=y is not set
-# CONFIG_SYSFS_DEPRECATED_V2=y is not set
-
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_LZO is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
# CONFIG_SYSCTL_SYSCALL is not set
@@ -70,31 +85,41 @@ CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+
+#
+# Kernel Performance Events And Counters
+#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+CONFIG_SLOW_WORK=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
@@ -102,11 +127,8 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_KMOD=y
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
@@ -114,33 +136,62 @@ CONFIG_BLOCK=y
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-CONFIG_CLASSIC_RCU=y
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
@@ -148,49 +199,58 @@ CONFIG_CLASSIC_RCU=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_NUC93X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5P6440 is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
CONFIG_ARCH_OMAP=y
-# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
#
# TI OMAP Implementations
#
CONFIG_ARCH_OMAP_OTG=y
# CONFIG_ARCH_OMAP1 is not set
+CONFIG_ARCH_OMAP2PLUS=y
# CONFIG_ARCH_OMAP2 is not set
CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
#
# OMAP Feature Selections
#
-# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
-# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
# CONFIG_OMAP_RESET_CLOCKS is not set
# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
# CONFIG_OMAP_MPU_TIMER is not set
CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_32K_TIMER_HZ=128
CONFIG_OMAP_DM_TIMER=y
-# CONFIG_OMAP_LL_DEBUG_UART1 is not set
-# CONFIG_OMAP_LL_DEBUG_UART2 is not set
-CONFIG_OMAP_LL_DEBUG_UART3=y
-CONFIG_ARCH_OMAP34XX=y
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
CONFIG_ARCH_OMAP3430=y
+CONFIG_OMAP_PACKAGE_CBB=y
#
# OMAP Board Type
@@ -198,15 +258,19 @@ CONFIG_ARCH_OMAP3430=y
# CONFIG_MACH_OMAP3_BEAGLE is not set
# CONFIG_MACH_OMAP_LDP is not set
# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
CONFIG_MACH_OMAP3_PANDORA=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+# CONFIG_MACH_CM_T35 is not set
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
#
# Processor Type
@@ -215,7 +279,7 @@ CONFIG_CPU_32v6K=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
-CONFIG_CPU_PABRT_IFAR=y
+CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
@@ -233,7 +297,12 @@ CONFIG_ARM_THUMBEE=y
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
CONFIG_HAS_TLS_REG=y
-# CONFIG_OUTER_CACHE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_CPU_HAS_PMU=y
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
#
# Bus support
@@ -253,13 +322,16 @@ CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -268,13 +340,14 @@ CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_LEDS is not set
CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
@@ -366,6 +439,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
@@ -379,7 +453,10 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
@@ -390,8 +467,14 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-# CONFIG_PHONET is not set
-# CONFIG_WIRELESS is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
@@ -403,6 +486,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
@@ -412,6 +497,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
@@ -462,6 +548,7 @@ CONFIG_MTD_CFI_I2=y
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
@@ -478,6 +565,9 @@ CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
@@ -486,6 +576,11 @@ CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
@@ -494,6 +589,10 @@ CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
@@ -502,7 +601,25 @@ CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-# CONFIG_MISC_DEVICES is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_TI_DAC7512 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IWMC3200TOP is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@@ -525,10 +642,6 @@ CONFIG_BLK_DEV_SD=y
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
@@ -545,8 +658,11 @@ CONFIG_SCSI_WAIT_SCAN=m
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
@@ -559,13 +675,13 @@ CONFIG_NETDEVICES=y
# CONFIG_NET_ETHERNET is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_HOSTAP is not set
#
-# Wireless LAN
+# Enable WiMAX (Networking options) to see the WiMAX drivers
#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
@@ -582,6 +698,7 @@ CONFIG_NETDEVICES=y
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
@@ -589,6 +706,7 @@ CONFIG_NETDEVICES=y
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
#
# Userland interfaces
@@ -605,13 +723,20 @@ CONFIG_INPUT_EVDEV=y
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_TWL4030=y
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
@@ -619,13 +744,22 @@ CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_GPIO is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
@@ -634,8 +768,18 @@ CONFIG_TOUCHSCREEN_ADS7846=y
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
CONFIG_INPUT_TWL4030_PWRBUTTON=y
+# CONFIG_INPUT_UINPUT is not set
+# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
#
# Hardware I/O ports
@@ -670,18 +814,21 @@ CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
+# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
@@ -692,10 +839,12 @@ CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_OMAP=y
# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
@@ -709,21 +858,6 @@ CONFIG_I2C_OMAP=y
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
-
-#
-# Miscellaneous I2C Chip support
-#
-# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_AT24 is not set
-# CONFIG_EEPROM_LEGACY is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_ISP1301_OMAP is not set
-# CONFIG_TPS65010 is not set
-# CONFIG_SENSORS_MAX6875 is not set
-# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -736,14 +870,21 @@ CONFIG_SPI_MASTER=y
# SPI Master Controller Drivers
#
# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
#
# SPI Protocol Masters
#
-# CONFIG_EEPROM_AT25 is not set
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
@@ -760,6 +901,7 @@ CONFIG_GPIOLIB=y
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCF857X is not set
CONFIG_GPIO_TWL4030=y
+# CONFIG_GPIO_ADP5588 is not set
#
# PCI GPIO expanders:
@@ -770,11 +912,16 @@ CONFIG_GPIO_TWL4030=y
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_ALS is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
@@ -786,44 +933,111 @@ CONFIG_SSB_POSSIBLE=y
#
# Multifunction device drivers
#
-# CONFIG_MFD_CORE is not set
+CONFIG_MFD_CORE=y
+# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_HTC_I2CPLD is not set
+# CONFIG_TPS65010 is not set
CONFIG_TWL4030_CORE=y
+CONFIG_TWL4030_POWER=y
+CONFIG_TWL4030_CODEC=y
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MFD_WM8994 is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_AB4500_CORE is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8649 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=0
+CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
+# CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+CONFIG_OMAP2_DSS_VENC=y
+# CONFIG_OMAP2_DSS_SDI is not set
+# CONFIG_OMAP2_DSS_DSI is not set
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+# CONFIG_PANEL_GENERIC is not set
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+# CONFIG_PANEL_SHARP_LQ043T1DG01 is not set
+# CONFIG_PANEL_TOPPOLY_TDO35S is not set
+CONFIG_PANEL_TPO_TD043MTEA1=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=y
#
# Display device support
@@ -835,6 +1049,16 @@ CONFIG_DAB=y
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
@@ -842,25 +1066,43 @@ CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_UA101 is not set
+# CONFIG_SND_USB_CAIAQ is not set
CONFIG_SND_SOC=y
CONFIG_SND_OMAP_SOC=y
CONFIG_SND_OMAP_SOC_MCBSP=y
CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
CONFIG_SND_SOC_TWL4030=y
-
+# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
@@ -873,31 +1115,40 @@ CONFIG_USB_HID=y
#
# Special HID drivers
#
-# CONFIG_HID_COMPAT is not set
+# CONFIG_HID_3M_PCT is not set
# CONFIG_HID_A4TECH is not set
# CONFIG_HID_APPLE is not set
# CONFIG_HID_BELKIN is not set
-# CONFIG_HID_BRIGHT is not set
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CYPRESS is not set
-# CONFIG_HID_DELL is not set
+# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_KYE is not set
# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_HID_MONTEREY is not set
+# CONFIG_HID_NTRIG is not set
+# CONFIG_HID_ORTEK is not set
# CONFIG_HID_PANTHERLORD is not set
# CONFIG_HID_PETALYNX is not set
+# CONFIG_HID_QUANTA is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
+# CONFIG_HID_STANTUM is not set
# CONFIG_HID_SUNPLUS is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
@@ -911,7 +1162,7 @@ CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-CONFIG_USB_MON=y
+# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set
@@ -919,7 +1170,13 @@ CONFIG_USB_MON=y
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
@@ -930,11 +1187,10 @@ CONFIG_USB_MUSB_SOC=y
#
# OMAP 343x high speed USB support
#
-CONFIG_USB_MUSB_HOST=y
-# CONFIG_USB_MUSB_PERIPHERAL is not set
+# CONFIG_USB_MUSB_HOST is not set
+CONFIG_USB_MUSB_PERIPHERAL=y
# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_HDRC_HCD=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
# CONFIG_MUSB_PIO_ONLY is not set
CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_TI_CPPI_DMA is not set
@@ -949,11 +1205,11 @@ CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_TMC is not set
#
-# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
-# see USB_STORAGE Help for more information
+# also be needed; see USB_STORAGE Help for more info
#
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
@@ -979,14 +1235,13 @@ CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
-# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
@@ -1002,27 +1257,46 @@ CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET_ATMEL_USBA is not set
# CONFIG_USB_GADGET_FSL_USB2 is not set
# CONFIG_USB_GADGET_LH7A40X is not set
-CONFIG_USB_GADGET_OMAP=y
-CONFIG_USB_OMAP=y
+# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
# CONFIG_USB_GADGET_S3C2410 is not set
# CONFIG_USB_GADGET_M66592 is not set
# CONFIG_USB_GADGET_AMD5536UDC is not set
# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
# CONFIG_USB_GADGET_NET2280 is not set
# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
-# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_GADGET_DUALSPEED=y
# CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
CONFIG_USB_ETH=y
CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
# CONFIG_USB_G_SERIAL is not set
# CONFIG_USB_MIDI_GADGET is not set
# CONFIG_USB_G_PRINTER is not set
# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_NOKIA is not set
+# CONFIG_USB_G_MULTI is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+# CONFIG_USB_ULPI is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
@@ -1040,16 +1314,41 @@ CONFIG_MMC_BLOCK_BOUNCE=y
#
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MMC_SPI is not set
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_REGULATOR is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+
+#
+# LED Triggers
+#
CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
@@ -1078,10 +1377,12 @@ CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
@@ -1093,6 +1394,7 @@ CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
@@ -1106,18 +1408,22 @@ CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_TWL4030=y
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
#
# File systems
@@ -1126,21 +1432,27 @@ CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
-CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
+CONFIG_FANOTIFY=y
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
@@ -1149,6 +1461,11 @@ CONFIG_QUOTACTL=y
# CONFIG_FUSE_FS is not set
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
@@ -1175,10 +1492,7 @@ CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
@@ -1187,7 +1501,9 @@ CONFIG_TMPFS=y
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS2_FS is not set
+# CONFIG_LOGFS is not set
# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
@@ -1196,7 +1512,20 @@ CONFIG_TMPFS=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+# CONFIG_NFS_FS is not set
+# CONFIG_NFSD is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CEPH_FS is not set
+CONFIG_CIFS=y
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
#
# Partition Types
@@ -1269,6 +1598,7 @@ CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
@@ -1277,11 +1607,15 @@ CONFIG_DEBUG_KERNEL=y
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
@@ -1299,33 +1633,42 @@ CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
-
-#
-# Tracers
-#
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
-# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_USER is not set
# CONFIG_DEBUG_ERRORS is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
#
# Security options
@@ -1333,19 +1676,22 @@ CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_AEAD=y
-CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_HASH2=y
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_CRYPTD is not set
@@ -1362,12 +1708,12 @@ CONFIG_CRYPTO_MANAGER=y
#
# Block modes
#
-CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CBC is not set
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
-CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
-CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set
#
@@ -1375,13 +1721,15 @@ CONFIG_CRYPTO_PCBC=m
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
-# CONFIG_CRYPTO_CRC32C is not set
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
@@ -1403,7 +1751,7 @@ CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
@@ -1416,33 +1764,33 @@ CONFIG_CRYPTO_DES=y
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
-CONFIG_LIBCRC32C=y
-CONFIG_PLIST=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
-
-# added by hand for now
-CONFIG_KEYBOARD_TWL4030=y
-CONFIG_USB_OTG_UTILS=y
-CONFIG_TWL4030_USB=y
-CONFIG_MMC_OMAP_HS=y
-
+CONFIG_NLATTR=y
+# CONFIG_SHM_SIGNAL is not set
+# CONFIG_IOQ is not set
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 07/23] omap3: pandora: update defconfig
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Grazvydas Ignotas <notasas@gmail.com>
Enable DSS2 and update defconfig for current kernel.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/omap3_pandora_defconfig | 678 +++++++++++++++++++++++-------
1 files changed, 513 insertions(+), 165 deletions(-)
diff --git a/arch/arm/configs/omap3_pandora_defconfig b/arch/arm/configs/omap3_pandora_defconfig
index f74eb9a..5d08e0b 100644
--- a/arch/arm/configs/omap3_pandora_defconfig
+++ b/arch/arm/configs/omap3_pandora_defconfig
@@ -1,15 +1,14 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc7
-# Fri Dec 5 11:54:09 2008
+# Linux kernel version: 2.6.33-rc6
+# Sat Feb 6 20:25:41 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
+CONFIG_HAVE_PROC_CPU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,13 +17,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
@@ -32,8 +31,15 @@ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
@@ -42,24 +48,33 @@ CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
-# CONFIG_SYSFS_DEPRECATED=y is not set
-# CONFIG_SYSFS_DEPRECATED_V2=y is not set
-
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_LZO is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
# CONFIG_SYSCTL_SYSCALL is not set
@@ -70,31 +85,41 @@ CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+
+#
+# Kernel Performance Events And Counters
+#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+CONFIG_SLOW_WORK=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
@@ -102,11 +127,8 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_KMOD=y
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
@@ -114,33 +136,62 @@ CONFIG_BLOCK=y
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-CONFIG_CLASSIC_RCU=y
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
@@ -148,49 +199,58 @@ CONFIG_CLASSIC_RCU=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_NUC93X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5P6440 is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
CONFIG_ARCH_OMAP=y
-# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
#
# TI OMAP Implementations
#
CONFIG_ARCH_OMAP_OTG=y
# CONFIG_ARCH_OMAP1 is not set
+CONFIG_ARCH_OMAP2PLUS=y
# CONFIG_ARCH_OMAP2 is not set
CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
#
# OMAP Feature Selections
#
-# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
-# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
# CONFIG_OMAP_RESET_CLOCKS is not set
# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
# CONFIG_OMAP_MPU_TIMER is not set
CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_32K_TIMER_HZ=128
CONFIG_OMAP_DM_TIMER=y
-# CONFIG_OMAP_LL_DEBUG_UART1 is not set
-# CONFIG_OMAP_LL_DEBUG_UART2 is not set
-CONFIG_OMAP_LL_DEBUG_UART3=y
-CONFIG_ARCH_OMAP34XX=y
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
CONFIG_ARCH_OMAP3430=y
+CONFIG_OMAP_PACKAGE_CBB=y
#
# OMAP Board Type
@@ -198,15 +258,19 @@ CONFIG_ARCH_OMAP3430=y
# CONFIG_MACH_OMAP3_BEAGLE is not set
# CONFIG_MACH_OMAP_LDP is not set
# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
CONFIG_MACH_OMAP3_PANDORA=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+# CONFIG_MACH_CM_T35 is not set
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
#
# Processor Type
@@ -215,7 +279,7 @@ CONFIG_CPU_32v6K=y
CONFIG_CPU_V7=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
-CONFIG_CPU_PABRT_IFAR=y
+CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
@@ -233,7 +297,12 @@ CONFIG_ARM_THUMBEE=y
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
CONFIG_HAS_TLS_REG=y
-# CONFIG_OUTER_CACHE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_CPU_HAS_PMU=y
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
#
# Bus support
@@ -253,13 +322,16 @@ CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -268,13 +340,14 @@ CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_LEDS is not set
CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
@@ -366,6 +439,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
@@ -379,7 +453,10 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
@@ -390,8 +467,14 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
-# CONFIG_PHONET is not set
-# CONFIG_WIRELESS is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
@@ -403,6 +486,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
@@ -412,6 +497,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
@@ -462,6 +548,7 @@ CONFIG_MTD_CFI_I2=y
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
@@ -478,6 +565,9 @@ CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
@@ -486,6 +576,11 @@ CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_ONENAND is not set
#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
@@ -494,6 +589,10 @@ CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
@@ -502,7 +601,25 @@ CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-# CONFIG_MISC_DEVICES is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_AD525X_DPOT is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_DS1682 is not set
+# CONFIG_TI_DAC7512 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_IWMC3200TOP is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@@ -525,10 +642,6 @@ CONFIG_BLK_DEV_SD=y
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
@@ -545,8 +658,11 @@ CONFIG_SCSI_WAIT_SCAN=m
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
@@ -559,13 +675,13 @@ CONFIG_NETDEVICES=y
# CONFIG_NET_ETHERNET is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_HOSTAP is not set
#
-# Wireless LAN
+# Enable WiMAX (Networking options) to see the WiMAX drivers
#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
@@ -582,6 +698,7 @@ CONFIG_NETDEVICES=y
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
@@ -589,6 +706,7 @@ CONFIG_NETDEVICES=y
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
#
# Userland interfaces
@@ -605,13 +723,20 @@ CONFIG_INPUT_EVDEV=y
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_TWL4030=y
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
@@ -619,13 +744,22 @@ CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_GPIO is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
@@ -634,8 +768,18 @@ CONFIG_TOUCHSCREEN_ADS7846=y
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
CONFIG_INPUT_TWL4030_PWRBUTTON=y
+# CONFIG_INPUT_UINPUT is not set
+# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
#
# Hardware I/O ports
@@ -670,18 +814,21 @@ CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
+# CONFIG_SERIAL_MAX3100 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
@@ -692,10 +839,12 @@ CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_OMAP=y
# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
@@ -709,21 +858,6 @@ CONFIG_I2C_OMAP=y
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
-
-#
-# Miscellaneous I2C Chip support
-#
-# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_AT24 is not set
-# CONFIG_EEPROM_LEGACY is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_ISP1301_OMAP is not set
-# CONFIG_TPS65010 is not set
-# CONFIG_SENSORS_MAX6875 is not set
-# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -736,14 +870,21 @@ CONFIG_SPI_MASTER=y
# SPI Master Controller Drivers
#
# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
#
# SPI Protocol Masters
#
-# CONFIG_EEPROM_AT25 is not set
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
@@ -760,6 +901,7 @@ CONFIG_GPIOLIB=y
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCF857X is not set
CONFIG_GPIO_TWL4030=y
+# CONFIG_GPIO_ADP5588 is not set
#
# PCI GPIO expanders:
@@ -770,11 +912,16 @@ CONFIG_GPIO_TWL4030=y
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_ALS is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
@@ -786,44 +933,111 @@ CONFIG_SSB_POSSIBLE=y
#
# Multifunction device drivers
#
-# CONFIG_MFD_CORE is not set
+CONFIG_MFD_CORE=y
+# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_HTC_I2CPLD is not set
+# CONFIG_TPS65010 is not set
CONFIG_TWL4030_CORE=y
+CONFIG_TWL4030_POWER=y
+CONFIG_TWL4030_CODEC=y
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MFD_WM8994 is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_AB4500_CORE is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8649 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=0
+CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
+# CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+CONFIG_OMAP2_DSS_VENC=y
+# CONFIG_OMAP2_DSS_SDI is not set
+# CONFIG_OMAP2_DSS_DSI is not set
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+# CONFIG_PANEL_GENERIC is not set
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+# CONFIG_PANEL_SHARP_LQ043T1DG01 is not set
+# CONFIG_PANEL_TOPPOLY_TDO35S is not set
+CONFIG_PANEL_TPO_TD043MTEA1=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=y
#
# Display device support
@@ -835,6 +1049,16 @@ CONFIG_DAB=y
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
CONFIG_SOUND_OSS_CORE_PRECLAIM=y
@@ -842,25 +1066,43 @@ CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_UA101 is not set
+# CONFIG_SND_USB_CAIAQ is not set
CONFIG_SND_SOC=y
CONFIG_SND_OMAP_SOC=y
CONFIG_SND_OMAP_SOC_MCBSP=y
CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
CONFIG_SND_SOC_TWL4030=y
-
+# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
@@ -873,31 +1115,40 @@ CONFIG_USB_HID=y
#
# Special HID drivers
#
-# CONFIG_HID_COMPAT is not set
+# CONFIG_HID_3M_PCT is not set
# CONFIG_HID_A4TECH is not set
# CONFIG_HID_APPLE is not set
# CONFIG_HID_BELKIN is not set
-# CONFIG_HID_BRIGHT is not set
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CYPRESS is not set
-# CONFIG_HID_DELL is not set
+# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_KYE is not set
# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_HID_MONTEREY is not set
+# CONFIG_HID_NTRIG is not set
+# CONFIG_HID_ORTEK is not set
# CONFIG_HID_PANTHERLORD is not set
# CONFIG_HID_PETALYNX is not set
+# CONFIG_HID_QUANTA is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
+# CONFIG_HID_STANTUM is not set
# CONFIG_HID_SUNPLUS is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
@@ -911,7 +1162,7 @@ CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-CONFIG_USB_MON=y
+# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set
@@ -919,7 +1170,13 @@ CONFIG_USB_MON=y
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
@@ -930,11 +1187,10 @@ CONFIG_USB_MUSB_SOC=y
#
# OMAP 343x high speed USB support
#
-CONFIG_USB_MUSB_HOST=y
-# CONFIG_USB_MUSB_PERIPHERAL is not set
+# CONFIG_USB_MUSB_HOST is not set
+CONFIG_USB_MUSB_PERIPHERAL=y
# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_HDRC_HCD=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
# CONFIG_MUSB_PIO_ONLY is not set
CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_TI_CPPI_DMA is not set
@@ -949,11 +1205,11 @@ CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_TMC is not set
#
-# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
-# see USB_STORAGE Help for more information
+# also be needed; see USB_STORAGE Help for more info
#
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
@@ -979,14 +1235,13 @@ CONFIG_USB_INVENTRA_DMA=y
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
-# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
@@ -1002,27 +1257,46 @@ CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET_ATMEL_USBA is not set
# CONFIG_USB_GADGET_FSL_USB2 is not set
# CONFIG_USB_GADGET_LH7A40X is not set
-CONFIG_USB_GADGET_OMAP=y
-CONFIG_USB_OMAP=y
+# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
# CONFIG_USB_GADGET_S3C2410 is not set
# CONFIG_USB_GADGET_M66592 is not set
# CONFIG_USB_GADGET_AMD5536UDC is not set
# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
# CONFIG_USB_GADGET_NET2280 is not set
# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
-# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_GADGET_DUALSPEED=y
# CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
CONFIG_USB_ETH=y
CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
# CONFIG_USB_G_SERIAL is not set
# CONFIG_USB_MIDI_GADGET is not set
# CONFIG_USB_G_PRINTER is not set
# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_NOKIA is not set
+# CONFIG_USB_G_MULTI is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+# CONFIG_USB_ULPI is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
@@ -1040,16 +1314,41 @@ CONFIG_MMC_BLOCK_BOUNCE=y
#
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MMC_SPI is not set
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_REGULATOR is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+
+#
+# LED Triggers
+#
CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
@@ -1078,10 +1377,12 @@ CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
@@ -1093,6 +1394,7 @@ CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
@@ -1106,18 +1408,22 @@ CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_TWL4030=y
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
#
# File systems
@@ -1126,21 +1432,27 @@ CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
-CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
+CONFIG_FANOTIFY=y
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
@@ -1149,6 +1461,11 @@ CONFIG_QUOTACTL=y
# CONFIG_FUSE_FS is not set
#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
@@ -1175,10 +1492,7 @@ CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
@@ -1187,7 +1501,9 @@ CONFIG_TMPFS=y
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS2_FS is not set
+# CONFIG_LOGFS is not set
# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
@@ -1196,7 +1512,20 @@ CONFIG_TMPFS=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+# CONFIG_NFS_FS is not set
+# CONFIG_NFSD is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CEPH_FS is not set
+CONFIG_CIFS=y
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
#
# Partition Types
@@ -1269,6 +1598,7 @@ CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
@@ -1277,11 +1607,15 @@ CONFIG_DEBUG_KERNEL=y
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
@@ -1299,33 +1633,42 @@ CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
-
-#
-# Tracers
-#
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
-# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_USER is not set
# CONFIG_DEBUG_ERRORS is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
#
# Security options
@@ -1333,19 +1676,22 @@ CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_AEAD=y
-CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_HASH2=y
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_CRYPTD is not set
@@ -1362,12 +1708,12 @@ CONFIG_CRYPTO_MANAGER=y
#
# Block modes
#
-CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CBC is not set
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
-CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
-CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set
#
@@ -1375,13 +1721,15 @@ CONFIG_CRYPTO_PCBC=m
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
-# CONFIG_CRYPTO_CRC32C is not set
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
@@ -1403,7 +1751,7 @@ CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
@@ -1416,33 +1764,33 @@ CONFIG_CRYPTO_DES=y
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set
#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
-CONFIG_LIBCRC32C=y
-CONFIG_PLIST=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
-
-# added by hand for now
-CONFIG_KEYBOARD_TWL4030=y
-CONFIG_USB_OTG_UTILS=y
-CONFIG_TWL4030_USB=y
-CONFIG_MMC_OMAP_HS=y
-
+CONFIG_NLATTR=y
+# CONFIG_SHM_SIGNAL is not set
+# CONFIG_IOQ is not set
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 08/23] omap3: Add platform data for the twl4030_codec MFD on IGEP v2
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 10 ++++++++++
1 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index adc1b46..71488b2 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -173,12 +173,22 @@ static void __init igep2_init_irq(void)
omap_gpio_init();
}
+static struct twl4030_codec_audio_data igep2_audio_data = {
+ .audio_mclk = 26000000,
+};
+
+static struct twl4030_codec_data igep2_codec_data = {
+ .audio_mclk = 26000000,
+ .audio = &igep2_audio_data,
+};
+
static struct twl4030_platform_data igep2_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
.usb = &igep2_usb_data,
+ .codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 08/23] omap3: Add platform data for the twl4030_codec MFD on IGEP v2
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 10 ++++++++++
1 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index adc1b46..71488b2 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -173,12 +173,22 @@ static void __init igep2_init_irq(void)
omap_gpio_init();
}
+static struct twl4030_codec_audio_data igep2_audio_data = {
+ .audio_mclk = 26000000,
+};
+
+static struct twl4030_codec_data igep2_codec_data = {
+ .audio_mclk = 26000000,
+ .audio = &igep2_audio_data,
+};
+
static struct twl4030_platform_data igep2_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
.usb = &igep2_usb_data,
+ .codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 09/23] omap3: Fix typo on IGEP v2 board
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Fix typo on IGEP v2 board
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index f90b225..2e81a6e 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -131,7 +131,7 @@ config MACH_CM_T35
select OMAP_MUX
config MACH_IGEP0020
- bool "IGEP0020"
+ bool "IGEP v2 board"
depends on ARCH_OMAP3
select OMAP_PACKAGE_CBB
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 09/23] omap3: Fix typo on IGEP v2 board
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Fix typo on IGEP v2 board
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index f90b225..2e81a6e 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -131,7 +131,7 @@ config MACH_CM_T35
select OMAP_MUX
config MACH_IGEP0020
- bool "IGEP0020"
+ bool "IGEP v2 board"
depends on ARCH_OMAP3
select OMAP_PACKAGE_CBB
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 10/23] omap3: Add platform init code for EHCI driver on IGEP v2
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add platform init code for EHCI driver on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 12 ++++++++++++
1 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 71488b2..f6102c7 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -213,6 +213,17 @@ static int __init igep2_i2c_init(void)
return 0;
}
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = IGEP2_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -227,6 +238,7 @@ static void __init igep2_init(void)
igep2_i2c_init();
omap_serial_init();
usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
igep2_init_smsc911x();
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 10/23] omap3: Add platform init code for EHCI driver on IGEP v2
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add platform init code for EHCI driver on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 12 ++++++++++++
1 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 71488b2..f6102c7 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -213,6 +213,17 @@ static int __init igep2_i2c_init(void)
return 0;
}
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = IGEP2_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -227,6 +238,7 @@ static void __init igep2_init(void)
igep2_i2c_init();
omap_serial_init();
usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
igep2_init_smsc911x();
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 11/23] omap3: Enable DSS2 for IGEP v2 board
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 75 ++++++++++++++++++++++++++++++++++
1 files changed, 75 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index f6102c7..f6899f9 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -28,6 +28,7 @@
#include <plat/common.h>
#include <plat/gpmc.h>
#include <plat/usb.h>
+#include <plat/display.h>
#include "mux.h"
#include "hsmmc.h"
@@ -38,6 +39,7 @@
#define IGEP2_GPIO_LED0_RED 26
#define IGEP2_GPIO_LED0_GREEN 27
#define IGEP2_GPIO_LED1_RED 28
+#define IGEP2_GPIO_DVI_PUP 170
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
@@ -164,6 +166,76 @@ static struct twl4030_usb_data igep2_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
+static int igep2_enable_dvi(struct omap_dss_device *dssdev)
+{
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1);
+
+ return 0;
+}
+
+static void igep2_disable_dvi(struct omap_dss_device *dssdev)
+{
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 0);
+}
+
+static struct omap_dss_device igep2_dvi_device = {
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .name = "dvi",
+ .driver_name = "generic_panel",
+ .phy.dpi.data_lines = 24,
+ .platform_enable = igep2_enable_dvi,
+ .platform_disable = igep2_disable_dvi,
+};
+
+static struct omap_dss_device *igep2_dss_devices[] = {
+ &igep2_dvi_device
+};
+
+static struct omap_dss_board_info igep2_dss_data = {
+ .num_devices = ARRAY_SIZE(igep2_dss_devices),
+ .devices = igep2_dss_devices,
+ .default_device = &igep2_dvi_device,
+};
+
+static struct platform_device igep2_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &igep2_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply igep2_vpll2_supply = {
+ .supply = "vdds_dsi",
+ .dev = &igep2_dss_device.dev,
+};
+
+static struct regulator_init_data igep2_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep2_vpll2_supply,
+};
+
+static void __init igep2_display_init(void)
+{
+ if (gpio_request(IGEP2_GPIO_DVI_PUP, "GPIO_DVI_PUP") &&
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
+ pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
+}
+
+static struct platform_device *igep2_devices[] __initdata = {
+ &igep2_dss_device,
+};
+
static void __init igep2_init_irq(void)
{
omap_board_config = igep2_config;
@@ -191,6 +263,7 @@ static struct twl4030_platform_data igep2_twldata = {
.codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
+ .vpll2 = &igep2_vpll2,
};
@@ -236,10 +309,12 @@ static void __init igep2_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
igep2_i2c_init();
+ platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
omap_serial_init();
usb_musb_init();
usb_ehci_init(&ehci_pdata);
+ igep2_display_init();
igep2_init_smsc911x();
/* GPIO userspace leds */
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 11/23] omap3: Enable DSS2 for IGEP v2 board
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 75 ++++++++++++++++++++++++++++++++++
1 files changed, 75 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index f6102c7..f6899f9 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -28,6 +28,7 @@
#include <plat/common.h>
#include <plat/gpmc.h>
#include <plat/usb.h>
+#include <plat/display.h>
#include "mux.h"
#include "hsmmc.h"
@@ -38,6 +39,7 @@
#define IGEP2_GPIO_LED0_RED 26
#define IGEP2_GPIO_LED0_GREEN 27
#define IGEP2_GPIO_LED1_RED 28
+#define IGEP2_GPIO_DVI_PUP 170
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
@@ -164,6 +166,76 @@ static struct twl4030_usb_data igep2_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
+static int igep2_enable_dvi(struct omap_dss_device *dssdev)
+{
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1);
+
+ return 0;
+}
+
+static void igep2_disable_dvi(struct omap_dss_device *dssdev)
+{
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 0);
+}
+
+static struct omap_dss_device igep2_dvi_device = {
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .name = "dvi",
+ .driver_name = "generic_panel",
+ .phy.dpi.data_lines = 24,
+ .platform_enable = igep2_enable_dvi,
+ .platform_disable = igep2_disable_dvi,
+};
+
+static struct omap_dss_device *igep2_dss_devices[] = {
+ &igep2_dvi_device
+};
+
+static struct omap_dss_board_info igep2_dss_data = {
+ .num_devices = ARRAY_SIZE(igep2_dss_devices),
+ .devices = igep2_dss_devices,
+ .default_device = &igep2_dvi_device,
+};
+
+static struct platform_device igep2_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &igep2_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply igep2_vpll2_supply = {
+ .supply = "vdds_dsi",
+ .dev = &igep2_dss_device.dev,
+};
+
+static struct regulator_init_data igep2_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .apply_uV = true,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep2_vpll2_supply,
+};
+
+static void __init igep2_display_init(void)
+{
+ if (gpio_request(IGEP2_GPIO_DVI_PUP, "GPIO_DVI_PUP") &&
+ gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
+ pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
+}
+
+static struct platform_device *igep2_devices[] __initdata = {
+ &igep2_dss_device,
+};
+
static void __init igep2_init_irq(void)
{
omap_board_config = igep2_config;
@@ -191,6 +263,7 @@ static struct twl4030_platform_data igep2_twldata = {
.codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
+ .vpll2 = &igep2_vpll2,
};
@@ -236,10 +309,12 @@ static void __init igep2_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
igep2_i2c_init();
+ platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
omap_serial_init();
usb_musb_init();
usb_ehci_init(&ehci_pdata);
+ igep2_display_init();
igep2_init_smsc911x();
/* GPIO userspace leds */
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 12/23] omap3: Add support for flash on IGEP v2 board
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 101 ++++++++++++++++++++++++++++++++++
1 files changed, 101 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index f6899f9..8ed935c 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -29,6 +29,7 @@
#include <plat/gpmc.h>
#include <plat/usb.h>
#include <plat/display.h>
+#include <plat/onenand.h>
#include "mux.h"
#include "hsmmc.h"
@@ -41,6 +42,105 @@
#define IGEP2_GPIO_LED1_RED 28
#define IGEP2_GPIO_DVI_PUP 170
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+ defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+#define ONENAND_MAP 0x20000000
+
+/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY )
+ * Since the device is equipped with two DataRAMs, and two-plane NAND
+ * Flash memory array, these two component enables simultaneous program
+ * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
+ * while Plane2 has only odd blocks such as block1, block3, block5.
+ * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
+ */
+
+static struct mtd_partition igep2_onenand_partitions[] = {
+ {
+ .name = "X-Loader",
+ .offset = 0,
+ .size = 2 * (64*(2*2048))
+ },
+ {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 6 * (64*(2*2048)),
+ },
+ {
+ .name = "Environment",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 2 * (64*(2*2048)),
+ },
+ {
+ .name = "Kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 12 * (64*(2*2048)),
+ },
+ {
+ .name = "File System",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static int igep2_onenand_setup(void __iomem *onenand_base, int freq)
+{
+ /* nothing is required to be setup for onenand as of now */
+ return 0;
+}
+
+static struct omap_onenand_platform_data igep2_onenand_data = {
+ .parts = igep2_onenand_partitions,
+ .nr_parts = ARRAY_SIZE(igep2_onenand_partitions),
+ .onenand_setup = igep2_onenand_setup,
+ .dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
+};
+
+static struct platform_device igep2_onenand_device = {
+ .name = "omap2-onenand",
+ .id = -1,
+ .dev = {
+ .platform_data = &igep2_onenand_data,
+ },
+};
+
+void __init igep2_flash_init(void)
+{
+ u8 cs = 0;
+ u8 onenandcs = GPMC_CS_NUM + 1;
+
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ /* Check if NAND/oneNAND is configured */
+ if ((ret & 0xC00) == 0x800)
+ /* NAND found */
+ pr_err("IGEP v2: Unsupported NAND found\n");
+ else {
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
+ if ((ret & 0x3F) == (ONENAND_MAP >> 24))
+ /* ONENAND found */
+ onenandcs = cs;
+ }
+ cs++;
+ }
+ if (onenandcs > GPMC_CS_NUM) {
+ pr_err("IGEP v2: Unable to find configuration in GPMC\n");
+ return;
+ }
+
+ if (onenandcs < GPMC_CS_NUM) {
+ igep2_onenand_data.cs = onenandcs;
+ if (platform_device_register(&igep2_onenand_device) < 0)
+ pr_err("IGEP v2: Unable to register OneNAND device\n");
+ }
+}
+
+#else
+void __init igep2_flash_init(void) {}
+#endif
+
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
@@ -314,6 +414,7 @@ static void __init igep2_init(void)
usb_musb_init();
usb_ehci_init(&ehci_pdata);
+ igep2_flash_init();
igep2_display_init();
igep2_init_smsc911x();
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 12/23] omap3: Add support for flash on IGEP v2 board
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 101 ++++++++++++++++++++++++++++++++++
1 files changed, 101 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index f6899f9..8ed935c 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -29,6 +29,7 @@
#include <plat/gpmc.h>
#include <plat/usb.h>
#include <plat/display.h>
+#include <plat/onenand.h>
#include "mux.h"
#include "hsmmc.h"
@@ -41,6 +42,105 @@
#define IGEP2_GPIO_LED1_RED 28
#define IGEP2_GPIO_DVI_PUP 170
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+ defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+#define ONENAND_MAP 0x20000000
+
+/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY )
+ * Since the device is equipped with two DataRAMs, and two-plane NAND
+ * Flash memory array, these two component enables simultaneous program
+ * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
+ * while Plane2 has only odd blocks such as block1, block3, block5.
+ * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
+ */
+
+static struct mtd_partition igep2_onenand_partitions[] = {
+ {
+ .name = "X-Loader",
+ .offset = 0,
+ .size = 2 * (64*(2*2048))
+ },
+ {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 6 * (64*(2*2048)),
+ },
+ {
+ .name = "Environment",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 2 * (64*(2*2048)),
+ },
+ {
+ .name = "Kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 12 * (64*(2*2048)),
+ },
+ {
+ .name = "File System",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static int igep2_onenand_setup(void __iomem *onenand_base, int freq)
+{
+ /* nothing is required to be setup for onenand as of now */
+ return 0;
+}
+
+static struct omap_onenand_platform_data igep2_onenand_data = {
+ .parts = igep2_onenand_partitions,
+ .nr_parts = ARRAY_SIZE(igep2_onenand_partitions),
+ .onenand_setup = igep2_onenand_setup,
+ .dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
+};
+
+static struct platform_device igep2_onenand_device = {
+ .name = "omap2-onenand",
+ .id = -1,
+ .dev = {
+ .platform_data = &igep2_onenand_data,
+ },
+};
+
+void __init igep2_flash_init(void)
+{
+ u8 cs = 0;
+ u8 onenandcs = GPMC_CS_NUM + 1;
+
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ /* Check if NAND/oneNAND is configured */
+ if ((ret & 0xC00) == 0x800)
+ /* NAND found */
+ pr_err("IGEP v2: Unsupported NAND found\n");
+ else {
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
+ if ((ret & 0x3F) == (ONENAND_MAP >> 24))
+ /* ONENAND found */
+ onenandcs = cs;
+ }
+ cs++;
+ }
+ if (onenandcs > GPMC_CS_NUM) {
+ pr_err("IGEP v2: Unable to find configuration in GPMC\n");
+ return;
+ }
+
+ if (onenandcs < GPMC_CS_NUM) {
+ igep2_onenand_data.cs = onenandcs;
+ if (platform_device_register(&igep2_onenand_device) < 0)
+ pr_err("IGEP v2: Unable to register OneNAND device\n");
+ }
+}
+
+#else
+void __init igep2_flash_init(void) {}
+#endif
+
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
@@ -314,6 +414,7 @@ static void __init igep2_init(void)
usb_musb_init();
usb_ehci_init(&ehci_pdata);
+ igep2_flash_init();
igep2_display_init();
igep2_init_smsc911x();
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 13/23] ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the
IGEP v2 board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h | 51 ++++++++++++++++++++++++
1 files changed, 51 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
diff --git a/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h b/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
new file mode 100644
index 0000000..cd43529
--- /dev/null
+++ b/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
@@ -0,0 +1,51 @@
+/*
+ * SDRC register values for the Numonyx M65KXXXXAM
+ *
+ * Copyright (C) 2009 Integration Software and Electronic Engineering.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
+#define __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
+
+#include <plat/sdrc.h>
+
+/* Numonyx M65KXXXXAM */
+static struct omap_sdrc_params m65kxxxxam_sdrc_params[] = {
+ [0] = {
+ .rate = 200000000,
+ .actim_ctrla = 0xe321d4c6,
+ .actim_ctrlb = 0x00022328,
+ .rfr_ctrl = 0x0005e601,
+ .mr = 0x00000032,
+ },
+ [1] = {
+ .rate = 166000000,
+ .actim_ctrla = 0xba9dc485,
+ .actim_ctrlb = 0x00022321,
+ .rfr_ctrl = 0x0004dc01,
+ .mr = 0x00000032,
+ },
+ [2] = {
+ .rate = 133000000,
+ .actim_ctrla = 0x9a19b485,
+ .actim_ctrlb = 0x0002231b,
+ .rfr_ctrl = 0x0003de01,
+ .mr = 0x00000032,
+ },
+ [3] = {
+ .rate = 83000000,
+ .actim_ctrla = 0x594ca242,
+ .actim_ctrlb = 0x00022310,
+ .rfr_ctrl = 0x00025501,
+ .mr = 0x00000032,
+ },
+ [4] = {
+ .rate = 0
+ },
+};
+
+#endif
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 13/23] ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the
IGEP v2 board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h | 51 ++++++++++++++++++++++++
1 files changed, 51 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
diff --git a/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h b/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
new file mode 100644
index 0000000..cd43529
--- /dev/null
+++ b/arch/arm/mach-omap2/sdram-numonyx-m65kxxxxam.h
@@ -0,0 +1,51 @@
+/*
+ * SDRC register values for the Numonyx M65KXXXXAM
+ *
+ * Copyright (C) 2009 Integration Software and Electronic Engineering.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
+#define __ARCH_ARM_MACH_OMAP2_SDRAM_NUMONYX_M65KXXXXAM
+
+#include <plat/sdrc.h>
+
+/* Numonyx M65KXXXXAM */
+static struct omap_sdrc_params m65kxxxxam_sdrc_params[] = {
+ [0] = {
+ .rate = 200000000,
+ .actim_ctrla = 0xe321d4c6,
+ .actim_ctrlb = 0x00022328,
+ .rfr_ctrl = 0x0005e601,
+ .mr = 0x00000032,
+ },
+ [1] = {
+ .rate = 166000000,
+ .actim_ctrla = 0xba9dc485,
+ .actim_ctrlb = 0x00022321,
+ .rfr_ctrl = 0x0004dc01,
+ .mr = 0x00000032,
+ },
+ [2] = {
+ .rate = 133000000,
+ .actim_ctrla = 0x9a19b485,
+ .actim_ctrlb = 0x0002231b,
+ .rfr_ctrl = 0x0003de01,
+ .mr = 0x00000032,
+ },
+ [3] = {
+ .rate = 83000000,
+ .actim_ctrla = 0x594ca242,
+ .actim_ctrlb = 0x00022310,
+ .rfr_ctrl = 0x00025501,
+ .mr = 0x00000032,
+ },
+ [4] = {
+ .rate = 0
+ },
+};
+
+#endif
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 14/23] omap3: Use timing data for omap2_init_common_hw on IGEP v2
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 8ed935c..3d1fde7 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -33,6 +33,7 @@
#include "mux.h"
#include "hsmmc.h"
+#include "sdram-numonyx-m65kxxxxam.h"
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
@@ -340,7 +341,7 @@ static void __init igep2_init_irq(void)
{
omap_board_config = igep2_config;
omap_board_config_size = ARRAY_SIZE(igep2_config);
- omap2_init_common_hw(NULL, NULL);
+ omap2_init_common_hw(m65kxxxxam_sdrc_params, m65kxxxxam_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 14/23] omap3: Use timing data for omap2_init_common_hw on IGEP v2
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 8ed935c..3d1fde7 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -33,6 +33,7 @@
#include "mux.h"
#include "hsmmc.h"
+#include "sdram-numonyx-m65kxxxxam.h"
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
@@ -340,7 +341,7 @@ static void __init igep2_init_irq(void)
{
omap_board_config = igep2_config;
omap_board_config_size = ARRAY_SIZE(igep2_config);
- omap2_init_common_hw(NULL, NULL);
+ omap2_init_common_hw(m65kxxxxam_sdrc_params, m65kxxxxam_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 15/23] omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Enric Balletbo i Serra, linux-omap
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/igep0020_defconfig | 525 +++++++++++++++++++++--------------
1 files changed, 309 insertions(+), 216 deletions(-)
diff --git a/arch/arm/configs/igep0020_defconfig b/arch/arm/configs/igep0020_defconfig
index a192248..e7940a9 100644
--- a/arch/arm/configs/igep0020_defconfig
+++ b/arch/arm/configs/igep0020_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.32-rc6
-# Fri Nov 13 12:01:17 2009
+# Linux kernel version: 2.6.33-rc3
+# Thu Jan 7 16:14:55 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -46,6 +46,7 @@ CONFIG_BSD_PROCESS_ACCT=y
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
@@ -126,14 +127,41 @@ CONFIG_LBDAF=y
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set
#
@@ -162,6 +190,7 @@ CONFIG_MMU=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
@@ -184,6 +213,7 @@ CONFIG_MMU=y
# CONFIG_ARCH_DAVINCI is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
#
# TI OMAP Implementations
@@ -197,12 +227,8 @@ CONFIG_ARCH_OMAP3=y
#
# OMAP Feature Selections
#
-# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
-# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
-# CONFIG_OMAP_RESET_CLOCKS is not set
-CONFIG_OMAP_MUX=y
-CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_OMAP_MUX_WARNINGS=y
+CONFIG_OMAP_RESET_CLOCKS=y
+# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_MCBSP=y
# CONFIG_OMAP_MBOX_FWK is not set
# CONFIG_OMAP_MPU_TIMER is not set
@@ -217,6 +243,7 @@ CONFIG_OMAP_LL_DEBUG_UART3=y
CONFIG_OMAP_PM_NOOP=y
CONFIG_ARCH_OMAP34XX=y
CONFIG_ARCH_OMAP3430=y
+CONFIG_OMAP_PACKAGE_CBB=y
#
# OMAP Board Type
@@ -227,13 +254,16 @@ CONFIG_ARCH_OMAP3430=y
# CONFIG_MACH_OMAP3EVM is not set
# CONFIG_MACH_OMAP3517EVM is not set
# CONFIG_MACH_OMAP3_PANDORA is not set
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
# CONFIG_MACH_OMAP_3430SDP is not set
# CONFIG_MACH_NOKIA_RX51 is not set
# CONFIG_MACH_OMAP_ZOOM2 is not set
-# CONFIG_MACH_CM_T35 is not set
# CONFIG_MACH_OMAP_ZOOM3 is not set
-# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_MACH_CM_T35 is not set
CONFIG_MACH_IGEP0020=y
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
#
# Processor Type
@@ -305,8 +335,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_MLOCKED_PAGE_BIT=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_LEDS is not set
@@ -440,35 +468,35 @@ CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
-CONFIG_BT_HCIBTUSB=m
+# CONFIG_BT_HCIBTUSB is not set
# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIUART_LL=y
-CONFIG_BT_HCIBCM203X=m
-CONFIG_BT_HCIBPA10X=m
-CONFIG_BT_HCIBFUSB=m
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
CONFIG_BT_HCIVHCI=m
CONFIG_BT_MRVL=m
CONFIG_BT_MRVL_SDIO=m
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
-CONFIG_CFG80211=m
+CONFIG_WIRELESS_EXT=y
+CONFIG_WEXT_CORE=y
+CONFIG_WEXT_PROC=y
+CONFIG_WEXT_SPY=y
+CONFIG_CFG80211=y
# CONFIG_NL80211_TESTMODE is not set
# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_CFG80211_DEFAULT_PS=y
-CONFIG_CFG80211_DEFAULT_PS_VALUE=1
# CONFIG_WIRELESS_OLD_REGULATORY is not set
-CONFIG_WIRELESS_EXT=y
+CONFIG_CFG80211_WEXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
-CONFIG_LIB80211=m
-CONFIG_LIB80211_CRYPT_WEP=m
-CONFIG_LIB80211_CRYPT_CCMP=m
-CONFIG_LIB80211_CRYPT_TKIP=m
+CONFIG_LIB80211=y
# CONFIG_LIB80211_DEBUG is not set
-CONFIG_MAC80211=m
+CONFIG_MAC80211=y
# CONFIG_MAC80211_RC_PID is not set
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
@@ -500,12 +528,95 @@ CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+CONFIG_MTD_ONENAND=y
+# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set
+# CONFIG_MTD_ONENAND_GENERIC is not set
+CONFIG_MTD_ONENAND_OMAP2=y
+# CONFIG_MTD_ONENAND_OTP is not set
+CONFIG_MTD_ONENAND_2X_PROGRAM=y
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
@@ -516,7 +627,6 @@ CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
# CONFIG_MISC_DEVICES is not set
-CONFIG_EEPROM_93CX6=m
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@@ -613,56 +723,26 @@ CONFIG_SMSC911X=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_WLAN=y
-# CONFIG_WLAN_PRE80211 is not set
-CONFIG_WLAN_80211=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-# CONFIG_LIBERTAS_SPI is not set
-# CONFIG_LIBERTAS_DEBUG is not set
# CONFIG_LIBERTAS_THINFIRM is not set
-CONFIG_AT76C50X_USB=m
-CONFIG_USB_ZD1201=m
-CONFIG_USB_NET_RNDIS_WLAN=m
-CONFIG_RTL8187=m
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+# CONFIG_RTL8187 is not set
# CONFIG_MAC80211_HWSIM is not set
-CONFIG_P54_COMMON=m
-CONFIG_P54_USB=m
-CONFIG_P54_SPI=m
-CONFIG_ATH_COMMON=m
-CONFIG_AR9170_USB=m
-CONFIG_HOSTAP=m
-CONFIG_HOSTAP_FIRMWARE=y
-CONFIG_HOSTAP_FIRMWARE_NVRAM=y
-CONFIG_B43=m
-# CONFIG_B43_SDIO is not set
-# CONFIG_B43_PHY_LP is not set
-CONFIG_B43_HWRNG=y
-# CONFIG_B43_DEBUG is not set
-CONFIG_B43LEGACY=m
-CONFIG_B43LEGACY_HWRNG=y
-# CONFIG_B43LEGACY_DEBUG is not set
-CONFIG_B43LEGACY_DMA=y
-CONFIG_B43LEGACY_PIO=y
-CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
-# CONFIG_B43LEGACY_DMA_MODE is not set
-# CONFIG_B43LEGACY_PIO_MODE is not set
-CONFIG_ZD1211RW=m
-# CONFIG_ZD1211RW_DEBUG is not set
-CONFIG_RT2X00=m
-CONFIG_RT2500USB=m
-CONFIG_RT73USB=m
-CONFIG_RT2800USB=m
-CONFIG_RT2X00_LIB_USB=m
-CONFIG_RT2X00_LIB=m
-CONFIG_RT2X00_LIB_HT=y
-CONFIG_RT2X00_LIB_FIRMWARE=y
-CONFIG_RT2X00_LIB_CRYPTO=y
-# CONFIG_RT2X00_DEBUG is not set
-CONFIG_WL12XX=m
-# CONFIG_WL1251 is not set
-# CONFIG_WL1271 is not set
+# CONFIG_ATH_COMMON is not set
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+# CONFIG_HOSTAP is not set
# CONFIG_IWM is not set
+CONFIG_LIBERTAS=y
+# CONFIG_LIBERTAS_USB is not set
+CONFIG_LIBERTAS_SDIO=y
+# CONFIG_LIBERTAS_SPI is not set
+# CONFIG_LIBERTAS_DEBUG is not set
+# CONFIG_P54_COMMON is not set
+# CONFIG_RT2X00 is not set
+# CONFIG_WL12XX is not set
+# CONFIG_ZD1211RW is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
@@ -672,29 +752,10 @@ CONFIG_WL12XX=m
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
-CONFIG_USB_USBNET=m
-CONFIG_USB_NET_AX8817X=m
-CONFIG_USB_NET_CDCETHER=m
-CONFIG_USB_NET_CDC_EEM=m
-CONFIG_USB_NET_DM9601=m
-CONFIG_USB_NET_SMSC95XX=m
-CONFIG_USB_NET_GL620A=m
-CONFIG_USB_NET_NET1080=m
-CONFIG_USB_NET_PLUSB=m
-CONFIG_USB_NET_MCS7830=m
-CONFIG_USB_NET_RNDIS_HOST=m
-CONFIG_USB_NET_CDC_SUBSET=m
-# CONFIG_USB_ALI_M5632 is not set
-# CONFIG_USB_AN2720 is not set
-CONFIG_USB_BELKIN=y
-CONFIG_USB_ARMLINUX=y
-# CONFIG_USB_EPSON2888 is not set
-# CONFIG_USB_KC2190 is not set
-CONFIG_USB_NET_ZAURUS=m
-# CONFIG_USB_NET_INT51X1 is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
@@ -710,6 +771,7 @@ CONFIG_USB_NET_ZAURUS=m
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
#
# Userland interfaces
@@ -809,7 +871,6 @@ CONFIG_I2C_OMAP=y
#
# Miscellaneous I2C Chip support
#
-# CONFIG_DS1682 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
@@ -825,6 +886,8 @@ CONFIG_SPI_MASTER=y
# CONFIG_SPI_BITBANG is not set
# CONFIG_SPI_GPIO is not set
CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
#
# SPI Protocol Masters
@@ -892,7 +955,7 @@ CONFIG_SSB_SDIOHOST_POSSIBLE=y
#
# Multifunction device drivers
#
-# CONFIG_MFD_CORE is not set
+CONFIG_MFD_CORE=y
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
@@ -900,11 +963,13 @@ CONFIG_SSB_SDIOHOST_POSSIBLE=y
# CONFIG_TPS65010 is not set
CONFIG_TWL4030_CORE=y
# CONFIG_TWL4030_POWER is not set
+CONFIG_TWL4030_CODEC=y
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
@@ -912,6 +977,8 @@ CONFIG_TWL4030_CORE=y
# CONFIG_MFD_MC13783 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
@@ -919,6 +986,7 @@ CONFIG_REGULATOR=y
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_BQ24022 is not set
# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
CONFIG_REGULATOR_TWL4030=y
# CONFIG_REGULATOR_LP3971 is not set
# CONFIG_REGULATOR_TPS65023 is not set
@@ -930,65 +998,129 @@ CONFIG_REGULATOR_TWL4030=y
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_MODE_HELPERS=y
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=14
+# CONFIG_OMAP2_DSS_DEBUG_SUPPORT is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+# CONFIG_OMAP2_DSS_VENC is not set
+# CONFIG_OMAP2_DSS_SDI is not set
+CONFIG_OMAP2_DSS_DSI=y
+CONFIG_OMAP2_DSS_USE_DSI_PLL=y
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+# CONFIG_FB_OMAP2_DEBUG_SUPPORT is not set
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+CONFIG_PANEL_GENERIC=y
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+# CONFIG_PANEL_TAAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
-# CONFIG_DISPLAY_SUPPORT is not set
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-# CONFIG_SOUND is not set
-CONFIG_HID_SUPPORT=y
-CONFIG_HID=y
-# CONFIG_HIDRAW is not set
-
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_HID_PID is not set
-# CONFIG_USB_HIDDEV is not set
-
-#
-# Special HID drivers
-#
-# CONFIG_HID_A4TECH is not set
-# CONFIG_HID_APPLE is not set
-# CONFIG_HID_BELKIN is not set
-# CONFIG_HID_CHERRY is not set
-# CONFIG_HID_CHICONY is not set
-# CONFIG_HID_CYPRESS is not set
-# CONFIG_HID_DRAGONRISE is not set
-# CONFIG_HID_EZKEY is not set
-# CONFIG_HID_KYE is not set
-# CONFIG_HID_GYRATION is not set
-# CONFIG_HID_TWINHAN is not set
-# CONFIG_HID_KENSINGTON is not set
-# CONFIG_HID_LOGITECH is not set
-# CONFIG_HID_MICROSOFT is not set
-# CONFIG_HID_MONTEREY is not set
-# CONFIG_HID_NTRIG is not set
-# CONFIG_HID_PANTHERLORD is not set
-# CONFIG_HID_PETALYNX is not set
-# CONFIG_HID_SAMSUNG is not set
-# CONFIG_HID_SONY is not set
-# CONFIG_HID_SUNPLUS is not set
-# CONFIG_HID_GREENASIA is not set
-# CONFIG_HID_SMARTJOYPLUS is not set
-# CONFIG_HID_TOPSEED is not set
-# CONFIG_HID_THRUSTMASTER is not set
-# CONFIG_HID_WACOM is not set
-# CONFIG_HID_ZEROPLUS is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE is not set
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
+# CONFIG_SND_MIXER_OSS is not set
+# CONFIG_SND_PCM_OSS is not set
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_MCBSP=y
+CONFIG_SND_OMAP_SOC_IGEP0020=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_TWL4030=y
+# CONFIG_SOUND_PRIME is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_HID=m
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
@@ -997,12 +1129,12 @@ CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
# Miscellaneous USB options
#
# CONFIG_USB_DEVICEFS is not set
-# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-CONFIG_USB_MON=m
+# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set
@@ -1010,29 +1142,21 @@ CONFIG_USB_MON=m
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
-# CONFIG_USB_OHCI_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HWA_HCD is not set
-CONFIG_USB_MUSB_HDRC=y
-CONFIG_USB_MUSB_SOC=y
-
-#
-# OMAP 343x high speed USB support
-#
-CONFIG_USB_MUSB_HOST=y
-# CONFIG_USB_MUSB_PERIPHERAL is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_HDRC_HCD=y
-# CONFIG_MUSB_PIO_ONLY is not set
-CONFIG_USB_INVENTRA_DMA=y
-# CONFIG_USB_TI_CPPI_DMA is not set
-# CONFIG_USB_MUSB_DEBUG is not set
+# CONFIG_USB_MUSB_HDRC is not set
#
# USB Device Class drivers
@@ -1049,19 +1173,7 @@ CONFIG_USB_INVENTRA_DMA=y
#
# also be needed; see USB_STORAGE Help for more info
#
-CONFIG_USB_STORAGE=m
-# CONFIG_USB_STORAGE_DEBUG is not set
-# CONFIG_USB_STORAGE_DATAFAB is not set
-# CONFIG_USB_STORAGE_FREECOM is not set
-# CONFIG_USB_STORAGE_ISD200 is not set
-# CONFIG_USB_STORAGE_USBAT is not set
-# CONFIG_USB_STORAGE_SDDR09 is not set
-# CONFIG_USB_STORAGE_SDDR55 is not set
-# CONFIG_USB_STORAGE_JUMPSHOT is not set
-# CONFIG_USB_STORAGE_ALAUDA is not set
-# CONFIG_USB_STORAGE_ONETOUCH is not set
-# CONFIG_USB_STORAGE_KARMA is not set
-# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
#
@@ -1099,41 +1211,7 @@ CONFIG_USB_STORAGE=m
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_DEBUG=y
-CONFIG_USB_GADGET_DEBUG_FILES=y
-CONFIG_USB_GADGET_VBUS_DRAW=2
-CONFIG_USB_GADGET_SELECTED=y
-# CONFIG_USB_GADGET_AT91 is not set
-# CONFIG_USB_GADGET_ATMEL_USBA is not set
-# CONFIG_USB_GADGET_FSL_USB2 is not set
-# CONFIG_USB_GADGET_LH7A40X is not set
-CONFIG_USB_GADGET_OMAP=y
-CONFIG_USB_OMAP=y
-# CONFIG_USB_GADGET_PXA25X is not set
-# CONFIG_USB_GADGET_R8A66597 is not set
-# CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C_HSOTG is not set
-# CONFIG_USB_GADGET_IMX is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
-# CONFIG_USB_GADGET_M66592 is not set
-# CONFIG_USB_GADGET_AMD5536UDC is not set
-# CONFIG_USB_GADGET_FSL_QE is not set
-# CONFIG_USB_GADGET_CI13XXX is not set
-# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_GOKU is not set
-# CONFIG_USB_GADGET_LANGWELL is not set
-# CONFIG_USB_GADGET_DUMMY_HCD is not set
-# CONFIG_USB_GADGET_DUALSPEED is not set
-CONFIG_USB_ZERO=m
-# CONFIG_USB_AUDIO is not set
-# CONFIG_USB_ETH is not set
-# CONFIG_USB_GADGETFS is not set
-# CONFIG_USB_FILE_STORAGE is not set
-# CONFIG_USB_G_SERIAL is not set
-# CONFIG_USB_MIDI_GADGET is not set
-# CONFIG_USB_G_PRINTER is not set
-# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_GADGET is not set
#
# OTG and related infrastructure
@@ -1141,10 +1219,11 @@ CONFIG_USB_ZERO=m
CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
-CONFIG_TWL4030_USB=y
+# CONFIG_USB_ULPI is not set
+# CONFIG_TWL4030_USB is not set
# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
-# CONFIG_MMC_DEBUG is not set
+CONFIG_MMC_DEBUG=y
# CONFIG_MMC_UNSAFE_RESUME is not set
#
@@ -1158,7 +1237,8 @@ CONFIG_MMC_BLOCK_BOUNCE=y
#
# MMC/SD/SDIO Host Controller Drivers
#
-# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_SDHCI=y
+# CONFIG_MMC_SDHCI_PLTFM is not set
# CONFIG_MMC_OMAP is not set
CONFIG_MMC_OMAP_HS=y
# CONFIG_MMC_AT91 is not set
@@ -1179,6 +1259,11 @@ CONFIG_RTC_LIB=y
# CONFIG_STAGING is not set
#
+# CBUS support
+#
+# CONFIG_CBUS is not set
+
+#
# File systems
#
CONFIG_EXT2_FS=y
@@ -1253,6 +1338,7 @@ CONFIG_MISC_FILESYSTEMS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
@@ -1401,6 +1487,7 @@ CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_TRACING_SUPPORT=y
@@ -1425,7 +1512,9 @@ CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_ERRORS is not set
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_LL=y
+# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_ICEDCC is not set
+# CONFIG_OC_ETM is not set
#
# Security options
@@ -1433,7 +1522,11 @@ CONFIG_DEBUG_LL=y
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 15/23] omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/igep0020_defconfig | 525 +++++++++++++++++++++--------------
1 files changed, 309 insertions(+), 216 deletions(-)
diff --git a/arch/arm/configs/igep0020_defconfig b/arch/arm/configs/igep0020_defconfig
index a192248..e7940a9 100644
--- a/arch/arm/configs/igep0020_defconfig
+++ b/arch/arm/configs/igep0020_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.32-rc6
-# Fri Nov 13 12:01:17 2009
+# Linux kernel version: 2.6.33-rc3
+# Thu Jan 7 16:14:55 2010
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -46,6 +46,7 @@ CONFIG_BSD_PROCESS_ACCT=y
#
CONFIG_TREE_RCU=y
# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
@@ -126,14 +127,41 @@ CONFIG_LBDAF=y
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
-CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
# CONFIG_FREEZER is not set
#
@@ -162,6 +190,7 @@ CONFIG_MMU=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
@@ -184,6 +213,7 @@ CONFIG_MMU=y
# CONFIG_ARCH_DAVINCI is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
#
# TI OMAP Implementations
@@ -197,12 +227,8 @@ CONFIG_ARCH_OMAP3=y
#
# OMAP Feature Selections
#
-# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
-# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
-# CONFIG_OMAP_RESET_CLOCKS is not set
-CONFIG_OMAP_MUX=y
-CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_OMAP_MUX_WARNINGS=y
+CONFIG_OMAP_RESET_CLOCKS=y
+# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_MCBSP=y
# CONFIG_OMAP_MBOX_FWK is not set
# CONFIG_OMAP_MPU_TIMER is not set
@@ -217,6 +243,7 @@ CONFIG_OMAP_LL_DEBUG_UART3=y
CONFIG_OMAP_PM_NOOP=y
CONFIG_ARCH_OMAP34XX=y
CONFIG_ARCH_OMAP3430=y
+CONFIG_OMAP_PACKAGE_CBB=y
#
# OMAP Board Type
@@ -227,13 +254,16 @@ CONFIG_ARCH_OMAP3430=y
# CONFIG_MACH_OMAP3EVM is not set
# CONFIG_MACH_OMAP3517EVM is not set
# CONFIG_MACH_OMAP3_PANDORA is not set
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
# CONFIG_MACH_OMAP_3430SDP is not set
# CONFIG_MACH_NOKIA_RX51 is not set
# CONFIG_MACH_OMAP_ZOOM2 is not set
-# CONFIG_MACH_CM_T35 is not set
# CONFIG_MACH_OMAP_ZOOM3 is not set
-# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_MACH_CM_T35 is not set
CONFIG_MACH_IGEP0020=y
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
#
# Processor Type
@@ -305,8 +335,6 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_MLOCKED_PAGE_BIT=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_LEDS is not set
@@ -440,35 +468,35 @@ CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
-CONFIG_BT_HCIBTUSB=m
+# CONFIG_BT_HCIBTUSB is not set
# CONFIG_BT_HCIBTSDIO is not set
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIUART_LL=y
-CONFIG_BT_HCIBCM203X=m
-CONFIG_BT_HCIBPA10X=m
-CONFIG_BT_HCIBFUSB=m
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
CONFIG_BT_HCIVHCI=m
CONFIG_BT_MRVL=m
CONFIG_BT_MRVL_SDIO=m
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
-CONFIG_CFG80211=m
+CONFIG_WIRELESS_EXT=y
+CONFIG_WEXT_CORE=y
+CONFIG_WEXT_PROC=y
+CONFIG_WEXT_SPY=y
+CONFIG_CFG80211=y
# CONFIG_NL80211_TESTMODE is not set
# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
CONFIG_CFG80211_DEFAULT_PS=y
-CONFIG_CFG80211_DEFAULT_PS_VALUE=1
# CONFIG_WIRELESS_OLD_REGULATORY is not set
-CONFIG_WIRELESS_EXT=y
+CONFIG_CFG80211_WEXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
-CONFIG_LIB80211=m
-CONFIG_LIB80211_CRYPT_WEP=m
-CONFIG_LIB80211_CRYPT_CCMP=m
-CONFIG_LIB80211_CRYPT_TKIP=m
+CONFIG_LIB80211=y
# CONFIG_LIB80211_DEBUG is not set
-CONFIG_MAC80211=m
+CONFIG_MAC80211=y
# CONFIG_MAC80211_RC_PID is not set
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
@@ -500,12 +528,95 @@ CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+CONFIG_MTD_ONENAND=y
+# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set
+# CONFIG_MTD_ONENAND_GENERIC is not set
+CONFIG_MTD_ONENAND_OMAP2=y
+# CONFIG_MTD_ONENAND_OTP is not set
+CONFIG_MTD_ONENAND_2X_PROGRAM=y
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
@@ -516,7 +627,6 @@ CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
# CONFIG_MISC_DEVICES is not set
-CONFIG_EEPROM_93CX6=m
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@@ -613,56 +723,26 @@ CONFIG_SMSC911X=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_WLAN=y
-# CONFIG_WLAN_PRE80211 is not set
-CONFIG_WLAN_80211=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-# CONFIG_LIBERTAS_SPI is not set
-# CONFIG_LIBERTAS_DEBUG is not set
# CONFIG_LIBERTAS_THINFIRM is not set
-CONFIG_AT76C50X_USB=m
-CONFIG_USB_ZD1201=m
-CONFIG_USB_NET_RNDIS_WLAN=m
-CONFIG_RTL8187=m
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+# CONFIG_RTL8187 is not set
# CONFIG_MAC80211_HWSIM is not set
-CONFIG_P54_COMMON=m
-CONFIG_P54_USB=m
-CONFIG_P54_SPI=m
-CONFIG_ATH_COMMON=m
-CONFIG_AR9170_USB=m
-CONFIG_HOSTAP=m
-CONFIG_HOSTAP_FIRMWARE=y
-CONFIG_HOSTAP_FIRMWARE_NVRAM=y
-CONFIG_B43=m
-# CONFIG_B43_SDIO is not set
-# CONFIG_B43_PHY_LP is not set
-CONFIG_B43_HWRNG=y
-# CONFIG_B43_DEBUG is not set
-CONFIG_B43LEGACY=m
-CONFIG_B43LEGACY_HWRNG=y
-# CONFIG_B43LEGACY_DEBUG is not set
-CONFIG_B43LEGACY_DMA=y
-CONFIG_B43LEGACY_PIO=y
-CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
-# CONFIG_B43LEGACY_DMA_MODE is not set
-# CONFIG_B43LEGACY_PIO_MODE is not set
-CONFIG_ZD1211RW=m
-# CONFIG_ZD1211RW_DEBUG is not set
-CONFIG_RT2X00=m
-CONFIG_RT2500USB=m
-CONFIG_RT73USB=m
-CONFIG_RT2800USB=m
-CONFIG_RT2X00_LIB_USB=m
-CONFIG_RT2X00_LIB=m
-CONFIG_RT2X00_LIB_HT=y
-CONFIG_RT2X00_LIB_FIRMWARE=y
-CONFIG_RT2X00_LIB_CRYPTO=y
-# CONFIG_RT2X00_DEBUG is not set
-CONFIG_WL12XX=m
-# CONFIG_WL1251 is not set
-# CONFIG_WL1271 is not set
+# CONFIG_ATH_COMMON is not set
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+# CONFIG_HOSTAP is not set
# CONFIG_IWM is not set
+CONFIG_LIBERTAS=y
+# CONFIG_LIBERTAS_USB is not set
+CONFIG_LIBERTAS_SDIO=y
+# CONFIG_LIBERTAS_SPI is not set
+# CONFIG_LIBERTAS_DEBUG is not set
+# CONFIG_P54_COMMON is not set
+# CONFIG_RT2X00 is not set
+# CONFIG_WL12XX is not set
+# CONFIG_ZD1211RW is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
@@ -672,29 +752,10 @@ CONFIG_WL12XX=m
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
-CONFIG_USB_USBNET=m
-CONFIG_USB_NET_AX8817X=m
-CONFIG_USB_NET_CDCETHER=m
-CONFIG_USB_NET_CDC_EEM=m
-CONFIG_USB_NET_DM9601=m
-CONFIG_USB_NET_SMSC95XX=m
-CONFIG_USB_NET_GL620A=m
-CONFIG_USB_NET_NET1080=m
-CONFIG_USB_NET_PLUSB=m
-CONFIG_USB_NET_MCS7830=m
-CONFIG_USB_NET_RNDIS_HOST=m
-CONFIG_USB_NET_CDC_SUBSET=m
-# CONFIG_USB_ALI_M5632 is not set
-# CONFIG_USB_AN2720 is not set
-CONFIG_USB_BELKIN=y
-CONFIG_USB_ARMLINUX=y
-# CONFIG_USB_EPSON2888 is not set
-# CONFIG_USB_KC2190 is not set
-CONFIG_USB_NET_ZAURUS=m
-# CONFIG_USB_NET_INT51X1 is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
@@ -710,6 +771,7 @@ CONFIG_USB_NET_ZAURUS=m
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
#
# Userland interfaces
@@ -809,7 +871,6 @@ CONFIG_I2C_OMAP=y
#
# Miscellaneous I2C Chip support
#
-# CONFIG_DS1682 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
@@ -825,6 +886,8 @@ CONFIG_SPI_MASTER=y
# CONFIG_SPI_BITBANG is not set
# CONFIG_SPI_GPIO is not set
CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
#
# SPI Protocol Masters
@@ -892,7 +955,7 @@ CONFIG_SSB_SDIOHOST_POSSIBLE=y
#
# Multifunction device drivers
#
-# CONFIG_MFD_CORE is not set
+CONFIG_MFD_CORE=y
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_HTC_EGPIO is not set
@@ -900,11 +963,13 @@ CONFIG_SSB_SDIOHOST_POSSIBLE=y
# CONFIG_TPS65010 is not set
CONFIG_TWL4030_CORE=y
# CONFIG_TWL4030_POWER is not set
+CONFIG_TWL4030_CODEC=y
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
@@ -912,6 +977,8 @@ CONFIG_TWL4030_CORE=y
# CONFIG_MFD_MC13783 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
@@ -919,6 +986,7 @@ CONFIG_REGULATOR=y
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_BQ24022 is not set
# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
CONFIG_REGULATOR_TWL4030=y
# CONFIG_REGULATOR_LP3971 is not set
# CONFIG_REGULATOR_TPS65023 is not set
@@ -930,65 +998,129 @@ CONFIG_REGULATOR_TWL4030=y
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_MODE_HELPERS=y
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=14
+# CONFIG_OMAP2_DSS_DEBUG_SUPPORT is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+# CONFIG_OMAP2_DSS_VENC is not set
+# CONFIG_OMAP2_DSS_SDI is not set
+CONFIG_OMAP2_DSS_DSI=y
+CONFIG_OMAP2_DSS_USE_DSI_PLL=y
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+# CONFIG_FB_OMAP2_DEBUG_SUPPORT is not set
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+CONFIG_PANEL_GENERIC=y
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+# CONFIG_PANEL_TAAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
-# CONFIG_DISPLAY_SUPPORT is not set
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-# CONFIG_SOUND is not set
-CONFIG_HID_SUPPORT=y
-CONFIG_HID=y
-# CONFIG_HIDRAW is not set
-
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_HID_PID is not set
-# CONFIG_USB_HIDDEV is not set
-
-#
-# Special HID drivers
-#
-# CONFIG_HID_A4TECH is not set
-# CONFIG_HID_APPLE is not set
-# CONFIG_HID_BELKIN is not set
-# CONFIG_HID_CHERRY is not set
-# CONFIG_HID_CHICONY is not set
-# CONFIG_HID_CYPRESS is not set
-# CONFIG_HID_DRAGONRISE is not set
-# CONFIG_HID_EZKEY is not set
-# CONFIG_HID_KYE is not set
-# CONFIG_HID_GYRATION is not set
-# CONFIG_HID_TWINHAN is not set
-# CONFIG_HID_KENSINGTON is not set
-# CONFIG_HID_LOGITECH is not set
-# CONFIG_HID_MICROSOFT is not set
-# CONFIG_HID_MONTEREY is not set
-# CONFIG_HID_NTRIG is not set
-# CONFIG_HID_PANTHERLORD is not set
-# CONFIG_HID_PETALYNX is not set
-# CONFIG_HID_SAMSUNG is not set
-# CONFIG_HID_SONY is not set
-# CONFIG_HID_SUNPLUS is not set
-# CONFIG_HID_GREENASIA is not set
-# CONFIG_HID_SMARTJOYPLUS is not set
-# CONFIG_HID_TOPSEED is not set
-# CONFIG_HID_THRUSTMASTER is not set
-# CONFIG_HID_WACOM is not set
-# CONFIG_HID_ZEROPLUS is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE is not set
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
+# CONFIG_SND_MIXER_OSS is not set
+# CONFIG_SND_PCM_OSS is not set
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_MCBSP=y
+CONFIG_SND_OMAP_SOC_IGEP0020=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_TWL4030=y
+# CONFIG_SOUND_PRIME is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_HID=m
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
@@ -997,12 +1129,12 @@ CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
# Miscellaneous USB options
#
# CONFIG_USB_DEVICEFS is not set
-# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-CONFIG_USB_MON=m
+# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set
@@ -1010,29 +1142,21 @@ CONFIG_USB_MON=m
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
-# CONFIG_USB_OHCI_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HWA_HCD is not set
-CONFIG_USB_MUSB_HDRC=y
-CONFIG_USB_MUSB_SOC=y
-
-#
-# OMAP 343x high speed USB support
-#
-CONFIG_USB_MUSB_HOST=y
-# CONFIG_USB_MUSB_PERIPHERAL is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_HDRC_HCD=y
-# CONFIG_MUSB_PIO_ONLY is not set
-CONFIG_USB_INVENTRA_DMA=y
-# CONFIG_USB_TI_CPPI_DMA is not set
-# CONFIG_USB_MUSB_DEBUG is not set
+# CONFIG_USB_MUSB_HDRC is not set
#
# USB Device Class drivers
@@ -1049,19 +1173,7 @@ CONFIG_USB_INVENTRA_DMA=y
#
# also be needed; see USB_STORAGE Help for more info
#
-CONFIG_USB_STORAGE=m
-# CONFIG_USB_STORAGE_DEBUG is not set
-# CONFIG_USB_STORAGE_DATAFAB is not set
-# CONFIG_USB_STORAGE_FREECOM is not set
-# CONFIG_USB_STORAGE_ISD200 is not set
-# CONFIG_USB_STORAGE_USBAT is not set
-# CONFIG_USB_STORAGE_SDDR09 is not set
-# CONFIG_USB_STORAGE_SDDR55 is not set
-# CONFIG_USB_STORAGE_JUMPSHOT is not set
-# CONFIG_USB_STORAGE_ALAUDA is not set
-# CONFIG_USB_STORAGE_ONETOUCH is not set
-# CONFIG_USB_STORAGE_KARMA is not set
-# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
#
@@ -1099,41 +1211,7 @@ CONFIG_USB_STORAGE=m
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_DEBUG=y
-CONFIG_USB_GADGET_DEBUG_FILES=y
-CONFIG_USB_GADGET_VBUS_DRAW=2
-CONFIG_USB_GADGET_SELECTED=y
-# CONFIG_USB_GADGET_AT91 is not set
-# CONFIG_USB_GADGET_ATMEL_USBA is not set
-# CONFIG_USB_GADGET_FSL_USB2 is not set
-# CONFIG_USB_GADGET_LH7A40X is not set
-CONFIG_USB_GADGET_OMAP=y
-CONFIG_USB_OMAP=y
-# CONFIG_USB_GADGET_PXA25X is not set
-# CONFIG_USB_GADGET_R8A66597 is not set
-# CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C_HSOTG is not set
-# CONFIG_USB_GADGET_IMX is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
-# CONFIG_USB_GADGET_M66592 is not set
-# CONFIG_USB_GADGET_AMD5536UDC is not set
-# CONFIG_USB_GADGET_FSL_QE is not set
-# CONFIG_USB_GADGET_CI13XXX is not set
-# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_GOKU is not set
-# CONFIG_USB_GADGET_LANGWELL is not set
-# CONFIG_USB_GADGET_DUMMY_HCD is not set
-# CONFIG_USB_GADGET_DUALSPEED is not set
-CONFIG_USB_ZERO=m
-# CONFIG_USB_AUDIO is not set
-# CONFIG_USB_ETH is not set
-# CONFIG_USB_GADGETFS is not set
-# CONFIG_USB_FILE_STORAGE is not set
-# CONFIG_USB_G_SERIAL is not set
-# CONFIG_USB_MIDI_GADGET is not set
-# CONFIG_USB_G_PRINTER is not set
-# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_GADGET is not set
#
# OTG and related infrastructure
@@ -1141,10 +1219,11 @@ CONFIG_USB_ZERO=m
CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
-CONFIG_TWL4030_USB=y
+# CONFIG_USB_ULPI is not set
+# CONFIG_TWL4030_USB is not set
# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
-# CONFIG_MMC_DEBUG is not set
+CONFIG_MMC_DEBUG=y
# CONFIG_MMC_UNSAFE_RESUME is not set
#
@@ -1158,7 +1237,8 @@ CONFIG_MMC_BLOCK_BOUNCE=y
#
# MMC/SD/SDIO Host Controller Drivers
#
-# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_SDHCI=y
+# CONFIG_MMC_SDHCI_PLTFM is not set
# CONFIG_MMC_OMAP is not set
CONFIG_MMC_OMAP_HS=y
# CONFIG_MMC_AT91 is not set
@@ -1179,6 +1259,11 @@ CONFIG_RTC_LIB=y
# CONFIG_STAGING is not set
#
+# CBUS support
+#
+# CONFIG_CBUS is not set
+
+#
# File systems
#
CONFIG_EXT2_FS=y
@@ -1253,6 +1338,7 @@ CONFIG_MISC_FILESYSTEMS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
@@ -1401,6 +1487,7 @@ CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_TRACING_SUPPORT=y
@@ -1425,7 +1512,9 @@ CONFIG_ARM_UNWIND=y
# CONFIG_DEBUG_ERRORS is not set
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_LL=y
+# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_ICEDCC is not set
+# CONFIG_OC_ETM is not set
#
# Security options
@@ -1433,7 +1522,11 @@ CONFIG_DEBUG_LL=y
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y
#
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 16/23] IGEPv2: Added WIFI support
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Jonas Zetterberg, linux-omap, Anders Hedlund
From: Jonas Zetterberg <jozz@jozz.se>
Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 40 ++++++++++++++++++++++++++++++++++
1 files changed, 40 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 3d1fde7..4a5d663 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -42,6 +42,8 @@
#define IGEP2_GPIO_LED0_GREEN 27
#define IGEP2_GPIO_LED1_RED 28
#define IGEP2_GPIO_DVI_PUP 170
+#define IGEP2_GPIO_WIFI_NPD 94
+#define IGEP2_GPIO_WIFI_NRESET 95
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
@@ -209,6 +211,10 @@ static struct regulator_consumer_supply igep2_vmmc1_supply = {
.supply = "vmmc",
};
+static struct regulator_consumer_supply igep2_vmmc2_supply = {
+ .supply = "vmmc",
+};
+
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
static struct regulator_init_data igep2_vmmc1 = {
.constraints = {
@@ -224,6 +230,21 @@ static struct regulator_init_data igep2_vmmc1 = {
.consumer_supplies = &igep2_vmmc1_supply,
};
+/* VMMC2 for OMAP VDD_MMC2 (i/o) and MMC2 WIFI */
+static struct regulator_init_data igep2_vmmc2 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep2_vmmc2_supply,
+};
+
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
@@ -251,6 +272,7 @@ static int igep2_twl_gpio_setup(struct device *dev,
* regulators will be set up only *after* we return.
*/
igep2_vmmc1_supply.dev = mmc[0].dev;
+ igep2_vmmc2_supply.dev = mmc[1].dev;
return 0;
};
@@ -364,6 +386,7 @@ static struct twl4030_platform_data igep2_twldata = {
.codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
+ .vmmc2 = &igep2_vmmc2,
.vpll2 = &igep2_vpll2,
};
@@ -440,6 +463,23 @@ static void __init igep2_init(void)
gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+
+ /* GPIO W-LAN + Bluetooth combo module */
+ if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
+ (gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
+ gpio_export(IGEP2_GPIO_WIFI_NPD, 0);
+/* gpio_set_value(IGEP2_GPIO_WIFI_NPD, 0); */
+ } else
+ pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NPD\n");
+
+ if ((gpio_request(IGEP2_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
+ (gpio_direction_output(IGEP2_GPIO_WIFI_NRESET, 1) == 0)) {
+ gpio_export(IGEP2_GPIO_WIFI_NRESET, 0);
+ gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 0);
+ udelay(10);
+ gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 1);
+ } else
+ pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NRESET\n");
}
static void __init igep2_map_io(void)
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 16/23] IGEPv2: Added WIFI support
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Jonas Zetterberg <jozz@jozz.se>
Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 40 ++++++++++++++++++++++++++++++++++
1 files changed, 40 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 3d1fde7..4a5d663 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -42,6 +42,8 @@
#define IGEP2_GPIO_LED0_GREEN 27
#define IGEP2_GPIO_LED1_RED 28
#define IGEP2_GPIO_DVI_PUP 170
+#define IGEP2_GPIO_WIFI_NPD 94
+#define IGEP2_GPIO_WIFI_NRESET 95
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
@@ -209,6 +211,10 @@ static struct regulator_consumer_supply igep2_vmmc1_supply = {
.supply = "vmmc",
};
+static struct regulator_consumer_supply igep2_vmmc2_supply = {
+ .supply = "vmmc",
+};
+
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
static struct regulator_init_data igep2_vmmc1 = {
.constraints = {
@@ -224,6 +230,21 @@ static struct regulator_init_data igep2_vmmc1 = {
.consumer_supplies = &igep2_vmmc1_supply,
};
+/* VMMC2 for OMAP VDD_MMC2 (i/o) and MMC2 WIFI */
+static struct regulator_init_data igep2_vmmc2 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &igep2_vmmc2_supply,
+};
+
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
@@ -251,6 +272,7 @@ static int igep2_twl_gpio_setup(struct device *dev,
* regulators will be set up only *after* we return.
*/
igep2_vmmc1_supply.dev = mmc[0].dev;
+ igep2_vmmc2_supply.dev = mmc[1].dev;
return 0;
};
@@ -364,6 +386,7 @@ static struct twl4030_platform_data igep2_twldata = {
.codec = &igep2_codec_data,
.gpio = &igep2_gpio_data,
.vmmc1 = &igep2_vmmc1,
+ .vmmc2 = &igep2_vmmc2,
.vpll2 = &igep2_vpll2,
};
@@ -440,6 +463,23 @@ static void __init igep2_init(void)
gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+
+ /* GPIO W-LAN + Bluetooth combo module */
+ if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
+ (gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
+ gpio_export(IGEP2_GPIO_WIFI_NPD, 0);
+/* gpio_set_value(IGEP2_GPIO_WIFI_NPD, 0); */
+ } else
+ pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NPD\n");
+
+ if ((gpio_request(IGEP2_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
+ (gpio_direction_output(IGEP2_GPIO_WIFI_NRESET, 1) == 0)) {
+ gpio_export(IGEP2_GPIO_WIFI_NRESET, 0);
+ gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 0);
+ udelay(10);
+ gpio_set_value(IGEP2_GPIO_WIFI_NRESET, 1);
+ } else
+ pr_warning("IGEP v2: Could not obtain gpio GPIO_WIFI_NRESET\n");
}
static void __init igep2_map_io(void)
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 17/23] IGEPv2: Use Red Led1 as Heartbeat if configured
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Jonas Zetterberg, linux-omap
From: Jonas Zetterberg <jozz@jozz.se>
If not configured it will be exported as normal GPIO led.
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 30 ++++++++++++++++++++++++++++--
1 files changed, 28 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 4a5d663..748f418 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -16,6 +16,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/gpio.h>
+#include <linux/leds.h>
#include <linux/interrupt.h>
#include <linux/regulator/machine.h>
@@ -354,9 +355,34 @@ static void __init igep2_display_init(void)
gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
}
+#ifdef CONFIG_LEDS_TRIGGERS
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "GPIO_LED1_RED",
+ .default_trigger = "heartbeat",
+ .gpio = IGEP2_GPIO_LED1_RED,
+ },
+};
+
+static struct gpio_led_platform_data gpio_leds_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_leds_info,
+ },
+};
+#endif
static struct platform_device *igep2_devices[] __initdata = {
&igep2_dss_device,
+#ifdef CONFIG_LEDS_TRIGGERS
+ &leds_gpio,
+#endif
};
static void __init igep2_init_irq(void)
@@ -456,14 +482,14 @@ static void __init igep2_init(void)
gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
-
+#ifndef CONFIG_LEDS_TRIGGERS
if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_LED1_RED") == 0) &&
(gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
gpio_export(IGEP2_GPIO_LED1_RED, 0);
gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
-
+#endif
/* GPIO W-LAN + Bluetooth combo module */
if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
(gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 17/23] IGEPv2: Use Red Led1 as Heartbeat if configured
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Jonas Zetterberg <jozz@jozz.se>
If not configured it will be exported as normal GPIO led.
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-igep0020.c | 30 ++++++++++++++++++++++++++++--
1 files changed, 28 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 4a5d663..748f418 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -16,6 +16,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/gpio.h>
+#include <linux/leds.h>
#include <linux/interrupt.h>
#include <linux/regulator/machine.h>
@@ -354,9 +355,34 @@ static void __init igep2_display_init(void)
gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
}
+#ifdef CONFIG_LEDS_TRIGGERS
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "GPIO_LED1_RED",
+ .default_trigger = "heartbeat",
+ .gpio = IGEP2_GPIO_LED1_RED,
+ },
+};
+
+static struct gpio_led_platform_data gpio_leds_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_leds_info,
+ },
+};
+#endif
static struct platform_device *igep2_devices[] __initdata = {
&igep2_dss_device,
+#ifdef CONFIG_LEDS_TRIGGERS
+ &leds_gpio,
+#endif
};
static void __init igep2_init_irq(void)
@@ -456,14 +482,14 @@ static void __init igep2_init(void)
gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
-
+#ifndef CONFIG_LEDS_TRIGGERS
if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_LED1_RED") == 0) &&
(gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
gpio_export(IGEP2_GPIO_LED1_RED, 0);
gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
} else
pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
-
+#endif
/* GPIO W-LAN + Bluetooth combo module */
if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
(gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 18/23] AM3517: Enable basic I2C Support
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Vaibhav Hiremath
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add basic I2C board Hook-up support, where all the 3 I2C instances
are getting registered.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 11 +++++++++++
1 files changed, 11 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index ad323b4..af99faf 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -38,6 +38,15 @@
#define LCD_PANEL_BKLIGHT_PWR 182
#define LCD_PANEL_PWM 181
+static int __init am3517_evm_i2c_init(void)
+{
+ omap_register_i2c_bus(1, 400, NULL, 0);
+ omap_register_i2c_bus(2, 400, NULL, 0);
+ omap_register_i2c_bus(3, 400, NULL, 0);
+
+ return 0;
+}
+
static int lcd_enabled;
static int dvi_enabled;
@@ -216,6 +225,8 @@ static struct omap_board_mux board_mux[] __initdata = {
static void __init am3517_evm_init(void)
{
+ am3517_evm_i2c_init();
+
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
platform_add_devices(am3517_evm_devices,
ARRAY_SIZE(am3517_evm_devices));
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 18/23] AM3517: Enable basic I2C Support
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add basic I2C board Hook-up support, where all the 3 I2C instances
are getting registered.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 11 +++++++++++
1 files changed, 11 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index ad323b4..af99faf 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -38,6 +38,15 @@
#define LCD_PANEL_BKLIGHT_PWR 182
#define LCD_PANEL_PWM 181
+static int __init am3517_evm_i2c_init(void)
+{
+ omap_register_i2c_bus(1, 400, NULL, 0);
+ omap_register_i2c_bus(2, 400, NULL, 0);
+ omap_register_i2c_bus(3, 400, NULL, 0);
+
+ return 0;
+}
+
static int lcd_enabled;
static int dvi_enabled;
@@ -216,6 +225,8 @@ static struct omap_board_mux board_mux[] __initdata = {
static void __init am3517_evm_init(void)
{
+ am3517_evm_i2c_init();
+
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
platform_add_devices(am3517_evm_devices,
ARRAY_SIZE(am3517_evm_devices));
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 19/23] AM3517: Enable RTC driver support for AM3517EVM
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Vaibhav Hiremath
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add platform hook-up interface to support RTC driver (S35390A).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 39 +++++++++++++++++++++++++++++++++
1 files changed, 39 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index af99faf..fe2446d 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -38,6 +38,39 @@
#define LCD_PANEL_BKLIGHT_PWR 182
#define LCD_PANEL_PWM 181
+static struct i2c_board_info __initdata am3517evm_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("s35390a", 0x30),
+ .type = "s35390a",
+ },
+};
+
+/*
+ * RTC - S35390A
+ */
+#define GPIO_RTCS35390A_IRQ 55
+
+static void __init am3517_evm_rtc_init(void)
+{
+ int r;
+
+ omap_mux_init_gpio(GPIO_RTCS35390A_IRQ, OMAP_PIN_INPUT_PULLUP);
+ r = gpio_request(GPIO_RTCS35390A_IRQ, "rtcs35390a-irq");
+ if (r < 0) {
+ printk(KERN_WARNING "failed to request GPIO#%d\n",
+ GPIO_RTCS35390A_IRQ);
+ return;
+ }
+ r = gpio_direction_input(GPIO_RTCS35390A_IRQ);
+ if (r < 0) {
+ printk(KERN_WARNING "GPIO#%d cannot be configured as input\n",
+ GPIO_RTCS35390A_IRQ);
+ gpio_free(GPIO_RTCS35390A_IRQ);
+ return;
+ }
+ am3517evm_i2c_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
+}
+
static int __init am3517_evm_i2c_init(void)
{
omap_register_i2c_bus(1, 400, NULL, 0);
@@ -235,6 +268,12 @@ static void __init am3517_evm_init(void)
usb_ehci_init(&ehci_pdata);
/* DSS */
am3517_evm_display_init();
+
+ /* RTC - S35390A */
+ am3517_evm_rtc_init();
+
+ i2c_register_board_info(1, am3517evm_i2c_boardinfo,
+ ARRAY_SIZE(am3517evm_i2c_boardinfo));
}
static void __init am3517_evm_map_io(void)
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 19/23] AM3517: Enable RTC driver support for AM3517EVM
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add platform hook-up interface to support RTC driver (S35390A).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 39 +++++++++++++++++++++++++++++++++
1 files changed, 39 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index af99faf..fe2446d 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -38,6 +38,39 @@
#define LCD_PANEL_BKLIGHT_PWR 182
#define LCD_PANEL_PWM 181
+static struct i2c_board_info __initdata am3517evm_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("s35390a", 0x30),
+ .type = "s35390a",
+ },
+};
+
+/*
+ * RTC - S35390A
+ */
+#define GPIO_RTCS35390A_IRQ 55
+
+static void __init am3517_evm_rtc_init(void)
+{
+ int r;
+
+ omap_mux_init_gpio(GPIO_RTCS35390A_IRQ, OMAP_PIN_INPUT_PULLUP);
+ r = gpio_request(GPIO_RTCS35390A_IRQ, "rtcs35390a-irq");
+ if (r < 0) {
+ printk(KERN_WARNING "failed to request GPIO#%d\n",
+ GPIO_RTCS35390A_IRQ);
+ return;
+ }
+ r = gpio_direction_input(GPIO_RTCS35390A_IRQ);
+ if (r < 0) {
+ printk(KERN_WARNING "GPIO#%d cannot be configured as input\n",
+ GPIO_RTCS35390A_IRQ);
+ gpio_free(GPIO_RTCS35390A_IRQ);
+ return;
+ }
+ am3517evm_i2c_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
+}
+
static int __init am3517_evm_i2c_init(void)
{
omap_register_i2c_bus(1, 400, NULL, 0);
@@ -235,6 +268,12 @@ static void __init am3517_evm_init(void)
usb_ehci_init(&ehci_pdata);
/* DSS */
am3517_evm_display_init();
+
+ /* RTC - S35390A */
+ am3517_evm_rtc_init();
+
+ i2c_register_board_info(1, am3517evm_i2c_boardinfo,
+ ARRAY_SIZE(am3517evm_i2c_boardinfo));
}
static void __init am3517_evm_map_io(void)
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 20/23] AM3517: Enable I2C-GPIO Expander driver support for AM3517EVM
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Vaibhav Hiremath
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add platform hook-up interface to support I2C based GPIo expander
(TCA6416).
There are 3 instances of I2C Expander on AM3517EVM,
- One is over I2C-2 mounted on Base board
- Two are over I2C3 mounted on UI Card
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 40 +++++++++++++++++++++++++++++++--
1 files changed, 38 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index fe2446d..e6b8967 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -20,6 +20,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/i2c/pca953x.h>
#include <mach/hardware.h>
#include <mach/am35xx.h>
@@ -71,11 +72,46 @@ static void __init am3517_evm_rtc_init(void)
am3517evm_i2c_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
}
+/*
+ * I2C GPIO Expander - TCA6416
+ */
+
+/* Mounted on Base-Board */
+static struct pca953x_platform_data am3517evm_gpio_expander_info_0 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+};
+static struct i2c_board_info __initdata am3517evm_tca6516_info_0[] = {
+ {
+ I2C_BOARD_INFO("tca6416", 0x21),
+ .platform_data = &am3517evm_gpio_expander_info_0,
+ },
+};
+
+/* Mounted on UI Card */
+static struct pca953x_platform_data am3517evm_ui_gpio_expander_info_1 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES + 16,
+};
+static struct pca953x_platform_data am3517evm_ui_gpio_expander_info_2 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES + 32,
+};
+static struct i2c_board_info __initdata am3517evm_ui_tca6516_info[] = {
+ {
+ I2C_BOARD_INFO("tca6416", 0x20),
+ .platform_data = &am3517evm_ui_gpio_expander_info_1,
+ },
+ {
+ I2C_BOARD_INFO("tca6416", 0x21),
+ .platform_data = &am3517evm_ui_gpio_expander_info_2,
+ },
+};
+
static int __init am3517_evm_i2c_init(void)
{
omap_register_i2c_bus(1, 400, NULL, 0);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
+ omap_register_i2c_bus(2, 400, am3517evm_tca6516_info_0,
+ ARRAY_SIZE(am3517evm_tca6516_info_0));
+ omap_register_i2c_bus(3, 400, am3517evm_ui_tca6516_info,
+ ARRAY_SIZE(am3517evm_ui_tca6516_info));
return 0;
}
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 20/23] AM3517: Enable I2C-GPIO Expander driver support for AM3517EVM
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Vaibhav Hiremath <hvaibhav@ti.com>
Add platform hook-up interface to support I2C based GPIo expander
(TCA6416).
There are 3 instances of I2C Expander on AM3517EVM,
- One is over I2C-2 mounted on Base board
- Two are over I2C3 mounted on UI Card
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-am3517evm.c | 40 +++++++++++++++++++++++++++++++--
1 files changed, 38 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index fe2446d..e6b8967 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -20,6 +20,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/i2c/pca953x.h>
#include <mach/hardware.h>
#include <mach/am35xx.h>
@@ -71,11 +72,46 @@ static void __init am3517_evm_rtc_init(void)
am3517evm_i2c_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
}
+/*
+ * I2C GPIO Expander - TCA6416
+ */
+
+/* Mounted on Base-Board */
+static struct pca953x_platform_data am3517evm_gpio_expander_info_0 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+};
+static struct i2c_board_info __initdata am3517evm_tca6516_info_0[] = {
+ {
+ I2C_BOARD_INFO("tca6416", 0x21),
+ .platform_data = &am3517evm_gpio_expander_info_0,
+ },
+};
+
+/* Mounted on UI Card */
+static struct pca953x_platform_data am3517evm_ui_gpio_expander_info_1 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES + 16,
+};
+static struct pca953x_platform_data am3517evm_ui_gpio_expander_info_2 = {
+ .gpio_base = OMAP_MAX_GPIO_LINES + 32,
+};
+static struct i2c_board_info __initdata am3517evm_ui_tca6516_info[] = {
+ {
+ I2C_BOARD_INFO("tca6416", 0x20),
+ .platform_data = &am3517evm_ui_gpio_expander_info_1,
+ },
+ {
+ I2C_BOARD_INFO("tca6416", 0x21),
+ .platform_data = &am3517evm_ui_gpio_expander_info_2,
+ },
+};
+
static int __init am3517_evm_i2c_init(void)
{
omap_register_i2c_bus(1, 400, NULL, 0);
- omap_register_i2c_bus(2, 400, NULL, 0);
- omap_register_i2c_bus(3, 400, NULL, 0);
+ omap_register_i2c_bus(2, 400, am3517evm_tca6516_info_0,
+ ARRAY_SIZE(am3517evm_tca6516_info_0));
+ omap_register_i2c_bus(3, 400, am3517evm_ui_tca6516_info,
+ ARRAY_SIZE(am3517evm_ui_tca6516_info));
return 0;
}
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 21/23] Add minimal support for DevKit8000
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Thomas Weber, linux-omap
From: Thomas Weber <weber@corscience.de>
These patches add board support for the Timll DevKit8000.
The DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 4
arch/arm/mach-omap2/Makefile | 2
arch/arm/mach-omap2/board-devkit8000.c | 691 ++++++++++++++++++++++++++++++++
3 files changed, 697 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-omap2/board-devkit8000.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 2e81a6e..a8a3d1e 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -58,6 +58,10 @@ config MACH_OMAP3_BEAGLE
depends on ARCH_OMAP3
select OMAP_PACKAGE_CBB
+config MACH_DEVKIT8000
+ bool "DEVKIT8000 board"
+ depends on ARCH_OMAP3
+
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index dfc49a0..d3e54da 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -91,6 +91,8 @@ obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o \
obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \
hsmmc.o
+obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o \
+ hsmmc.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o \
hsmmc.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o \
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
new file mode 100644
index 0000000..89a55f1
--- /dev/null
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -0,0 +1,691 @@
+/*
+ * board-devkit8000.c - TimLL Devkit8000
+ *
+ * Copyright (C) 2009 Kim Botherway
+ * Copyright (C) 2010 Thomas Weber
+ *
+ * Modified from mach-omap2/board-omap3beagle.c
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
+#include <plat/nand.h>
+#include <plat/usb.h>
+#include <plat/timer-gp.h>
+#include <plat/display.h>
+
+#include <plat/mcspi.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/usb/otg.h>
+#include <linux/dm9000.h>
+#include <linux/interrupt.h>
+
+#include "sdram-micron-mt46h32m32lf-6.h"
+
+#include "mux.h"
+#include "hsmmc.h"
+
+#define GPMC_CS0_BASE 0x60
+#define GPMC_CS_SIZE 0x30
+
+#define NAND_BLOCK_SIZE SZ_128K
+
+#define OMAP_DM9000_GPIO_IRQ 25
+#define OMAP3_DEVKIT_TS_GPIO 27
+
+static struct mtd_partition devkit8000_nand_partitions[] = {
+ /* All the partition sizes are listed in terms of NAND block size */
+ {
+ .name = "X-Loader",
+ .offset = 0,
+ .size = 4 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
+ .size = 15 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot Env",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
+ .size = 1 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "Kernel",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
+ .size = 32 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "File System",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct omap_nand_platform_data devkit8000_nand_data = {
+ .options = NAND_BUSWIDTH_16,
+ .parts = devkit8000_nand_partitions,
+ .nr_parts = ARRAY_SIZE(devkit8000_nand_partitions),
+ .dma_channel = -1, /* disable DMA in OMAP NAND driver */
+};
+
+static struct resource devkit8000_nand_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device devkit8000_nand_device = {
+ .name = "omap2-nand",
+ .id = -1,
+ .dev = {
+ .platform_data = &devkit8000_nand_data,
+ },
+ .num_resources = 1,
+ .resource = &devkit8000_nand_resource,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ .wires = 8,
+ .gpio_wp = 29,
+ },
+ {} /* Terminator */
+};
+static struct omap_board_config_kernel devkit8000_config[] __initdata = {
+};
+
+static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
+{
+ twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
+ twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
+
+ return 0;
+}
+
+static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
+{
+}
+static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
+{
+ return 0;
+}
+
+static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
+{
+}
+
+static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
+{
+
+ return 0;
+}
+
+static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
+{
+}
+
+
+static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+static struct regulator_consumer_supply devkit8000_vsim_supply = {
+ .supply = "vmmc_aux",
+};
+
+
+static struct omap_dss_device devkit8000_lcd_device = {
+ .name = "lcd",
+ .driver_name = "innolux_at_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .platform_enable = devkit8000_panel_enable_lcd,
+ .platform_disable = devkit8000_panel_disable_lcd,
+};
+static struct omap_dss_device devkit8000_dvi_device = {
+ .name = "dvi",
+ .driver_name = "generic_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .platform_enable = devkit8000_panel_enable_dvi,
+ .platform_disable = devkit8000_panel_disable_dvi,
+};
+
+static struct omap_dss_device devkit8000_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+ .platform_enable = devkit8000_panel_enable_tv,
+ .platform_disable = devkit8000_panel_disable_tv,
+};
+
+
+static struct omap_dss_device *devkit8000_dss_devices[] = {
+ &devkit8000_lcd_device,
+ &devkit8000_dvi_device,
+ &devkit8000_tv_device,
+};
+
+static struct omap_dss_board_info devkit8000_dss_data = {
+ .num_devices = ARRAY_SIZE(devkit8000_dss_devices),
+ .devices = devkit8000_dss_devices,
+ .default_device = &devkit8000_lcd_device,
+};
+
+static struct platform_device devkit8000_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &devkit8000_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply devkit8000_vdda_dac_supply = {
+ .supply = "vdda_dac",
+ .dev = &devkit8000_dss_device.dev,
+};
+
+static int board_keymap[] = {
+ KEY(0, 0, KEY_1),
+ KEY(1, 0, KEY_2),
+ KEY(2, 0, KEY_3),
+ KEY(0, 1, KEY_4),
+ KEY(1, 1, KEY_5),
+ KEY(2, 1, KEY_6),
+ KEY(3, 1, KEY_F5),
+ KEY(0, 2, KEY_7),
+ KEY(1, 2, KEY_8),
+ KEY(2, 2, KEY_9),
+ KEY(3, 2, KEY_F6),
+ KEY(0, 3, KEY_F7),
+ KEY(1, 3, KEY_0),
+ KEY(2, 3, KEY_F8),
+ PERSISTENT_KEY(4, 5),
+ KEY(4, 4, KEY_VOLUMEUP),
+ KEY(5, 5, KEY_VOLUMEDOWN),
+ 0
+};
+
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
+static struct twl4030_keypad_data devkit8000_kp_data = {
+ .keymap_data = &board_map_data,
+ .rows = 6,
+ .cols = 6,
+ .rep = 1,
+};
+
+static struct gpio_led gpio_leds[];
+
+static int devkit8000_twl_gpio_setup(struct device *dev,
+ unsigned gpio, unsigned ngpio)
+{
+ omap_mux_init_gpio(29, OMAP_PIN_INPUT);
+ /* gpio + 0 is "mmc0_cd" (input/IRQ) */
+ mmc[0].gpio_cd = gpio + 0;
+ omap2_hsmmc_init(mmc);
+
+ /* link regulators to MMC adapters */
+ devkit8000_vmmc1_supply.dev = mmc[0].dev;
+ devkit8000_vsim_supply.dev = mmc[0].dev;
+
+ /* REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+
+ gpio_request(gpio + 1, "EHCI_nOC");
+ gpio_direction_input(gpio + 1);
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
+ gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
+ gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
+
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+ return 0;
+}
+
+static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+ .irq_base = TWL4030_GPIO_IRQ_BASE,
+ .irq_end = TWL4030_GPIO_IRQ_END,
+ .use_leds = true,
+ .pullups = BIT(1),
+ .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
+ | BIT(15) | BIT(16) | BIT(17),
+ .setup = devkit8000_twl_gpio_setup,
+};
+
+static struct regulator_consumer_supply devkit8000_vpll2_supplies[] = {
+ {
+ .supply = "vdvi",
+ .dev = &devkit8000_lcd_device.dev,
+ },
+ {
+ .supply = "vdss_dsi",
+ .dev = &devkit8000_dss_device.dev,
+ }
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data devkit8000_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vmmc1_supply,
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data devkit8000_vsim = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vsim_supply,
+};
+
+/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
+static struct regulator_init_data devkit8000_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vdda_dac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data devkit8000_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(devkit8000_vpll2_supplies),
+ .consumer_supplies = devkit8000_vpll2_supplies,
+};
+
+static struct twl4030_usb_data devkit8000_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
+static struct twl4030_codec_audio_data devkit8000_audio_data = {
+ .audio_mclk = 26000000,
+};
+
+static struct twl4030_codec_data devkit8000_codec_data = {
+ .audio_mclk = 26000000,
+ .audio = &devkit8000_audio_data,
+};
+
+static struct twl4030_platform_data devkit8000_twldata = {
+ .irq_base = TWL4030_IRQ_BASE,
+ .irq_end = TWL4030_IRQ_END,
+
+ /* platform_data for children goes here */
+ .usb = &devkit8000_usb_data,
+ .gpio = &devkit8000_gpio_data,
+ .codec = &devkit8000_codec_data,
+ .vmmc1 = &devkit8000_vmmc1,
+ .vsim = &devkit8000_vsim,
+ .vdac = &devkit8000_vdac,
+ .vpll2 = &devkit8000_vpll2,
+ .keypad = &devkit8000_kp_data,
+};
+
+static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("twl4030", 0x48),
+ .flags = I2C_CLIENT_WAKE,
+ .irq = INT_34XX_SYS_NIRQ,
+ .platform_data = &devkit8000_twldata,
+ },
+};
+
+static int __init devkit8000_i2c_init(void)
+{
+ omap_register_i2c_bus(1, 2600, devkit8000_i2c_boardinfo,
+ ARRAY_SIZE(devkit8000_i2c_boardinfo));
+ /* Bus 3 is attached to the DVI port where devices like the pico DLP
+ * projector don't work reliably with 400kHz */
+ omap_register_i2c_bus(3, 400, NULL, 0);
+ return 0;
+}
+
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "led1",
+ .default_trigger = "heartbeat",
+ .gpio = 186,
+ .active_low = true,
+ },
+ {
+ .name = "led2",
+ .default_trigger = "mmc0",
+ .gpio = 163,
+ .active_low = true,
+ },
+ {
+ .name = "ledB",
+ .default_trigger = "none",
+ .gpio = 153,
+ .active_low = true,
+ },
+ {
+ .name = "led3",
+ .default_trigger = "none",
+ .gpio = 164,
+ .active_low = true,
+ },
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_led_info,
+ },
+};
+
+static struct gpio_keys_button gpio_buttons[] = {
+ {
+ .code = BTN_EXTRA,
+ .gpio = 26,
+ .desc = "user",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data gpio_key_info = {
+ .buttons = gpio_buttons,
+ .nbuttons = ARRAY_SIZE(gpio_buttons),
+};
+
+static struct platform_device keys_gpio = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_key_info,
+ },
+};
+
+
+static void __init devkit8000_init_irq(void)
+{
+ omap_board_config = devkit8000_config;
+ omap_board_config_size = ARRAY_SIZE(devkit8000_config);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
+ omap_init_irq();
+#ifdef CONFIG_OMAP_32K_TIMER
+ omap2_gp_clockevent_set_gptimer(12);
+#endif
+ omap_gpio_init();
+}
+
+static void __init devkit8000_ads7846_init(void)
+{
+ int gpio = OMAP3_DEVKIT_TS_GPIO;
+ int ret;
+
+ ret = gpio_request(gpio, "ads7846_pen_down");
+ if (ret < 0) {
+ printk(KERN_ERR "Failed to request GPIO %d for "
+ "ads7846 pen down IRQ\n", gpio);
+ return;
+ }
+
+ gpio_direction_input(gpio);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+ return !gpio_get_value(OMAP3_DEVKIT_TS_GPIO);
+}
+
+static struct ads7846_platform_data ads7846_config = {
+ .x_max = 0x0fff,
+ .y_max = 0x0fff,
+ .x_plate_ohms = 180,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 5,
+ .debounce_rep = 1,
+ .get_pendown_state = ads7846_get_pendown_state,
+ .keep_vref_on = 1,
+ .settle_delay_usecs = 150,
+};
+
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info devkit8000_spi_board_info[] __initdata = {
+ {
+ .modalias = "ads7846",
+ .bus_num = 2,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &ads7846_mcspi_config,
+ .irq = OMAP_GPIO_IRQ(OMAP3_DEVKIT_TS_GPIO),
+ .platform_data = &ads7846_config,
+ }
+};
+
+#define OMAP_DM9000_BASE 0x2c000000
+
+static struct resource omap_dm9000_resources[] = {
+ [0] = {
+ .start = OMAP_DM9000_BASE,
+ .end = (OMAP_DM9000_BASE + 0x4 - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = (OMAP_DM9000_BASE + 0x400),
+ .end = (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = OMAP_GPIO_IRQ(OMAP_DM9000_GPIO_IRQ),
+ .flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
+ },
+};
+
+static struct dm9000_plat_data omap_dm9000_platdata = {
+ .flags = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device omap_dm9000_dev = {
+ .name = "dm9000",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(omap_dm9000_resources),
+ .resource = omap_dm9000_resources,
+ .dev = {
+ .platform_data = &omap_dm9000_platdata,
+ },
+};
+
+static void __init omap_dm9000_init(void)
+{
+ if (gpio_request(OMAP_DM9000_GPIO_IRQ, "dm9000 irq") < 0) {
+ printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
+ OMAP_DM9000_GPIO_IRQ);
+ return;
+ }
+
+ gpio_direction_input(OMAP_DM9000_GPIO_IRQ);
+}
+
+static struct platform_device *devkit8000_devices[] __initdata = {
+ &devkit8000_dss_device,
+ &leds_gpio,
+ &keys_gpio,
+ &omap_dm9000_dev,
+};
+
+static void __init devkit8000_flash_init(void)
+{
+ u8 cs = 0;
+ u8 nandcs = GPMC_CS_NUM + 1;
+
+ u32 gpmc_base_add = OMAP34XX_GPMC_VIRT;
+
+ /* find out the chip-select on which NAND exists */
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ if ((ret & 0xC00) == 0x800) {
+ printk(KERN_INFO "Found NAND on CS%d\n", cs);
+ if (nandcs > GPMC_CS_NUM)
+ nandcs = cs;
+ }
+ cs++;
+ }
+
+ if (nandcs > GPMC_CS_NUM) {
+ printk(KERN_INFO "NAND: Unable to find configuration "
+ "in GPMC\n ");
+ return;
+ }
+
+ if (nandcs < GPMC_CS_NUM) {
+ devkit8000_nand_data.cs = nandcs;
+ devkit8000_nand_data.gpmc_cs_baseaddr = (void *)
+ (gpmc_base_add + GPMC_CS0_BASE + nandcs * GPMC_CS_SIZE);
+ devkit8000_nand_data.gpmc_baseaddr = (void *)
+ (gpmc_base_add);
+
+ printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
+ if (platform_device_register(&devkit8000_nand_device) < 0)
+ printk(KERN_ERR "Unable to register NAND device\n");
+ }
+}
+
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 147,
+ .reset_gpio_port[2] = -EINVAL
+};
+
+static void __init devkit8000_init(void)
+{
+ devkit8000_i2c_init();
+ platform_add_devices(devkit8000_devices,
+ ARRAY_SIZE(devkit8000_devices));
+ omap_board_config = devkit8000_config;
+ omap_board_config_size = ARRAY_SIZE(devkit8000_config);
+
+ spi_register_board_info(devkit8000_spi_board_info,
+ ARRAY_SIZE(devkit8000_spi_board_info));
+
+ omap_serial_init();
+
+ omap_dm9000_init();
+
+ devkit8000_ads7846_init();
+
+ omap_mux_init_gpio(170, OMAP_PIN_INPUT);
+
+ gpio_request(170, "DVI_nPD");
+ /* REVISIT leave DVI powered down until it's needed ... */
+ gpio_direction_output(170, true);
+
+ usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
+ devkit8000_flash_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
+}
+
+static void __init devkit8000_map_io(void)
+{
+ omap2_set_globals_343x();
+ omap34xx_map_common_io();
+}
+
+MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = devkit8000_map_io,
+ .init_irq = devkit8000_init_irq,
+ .init_machine = devkit8000_init,
+ .timer = &omap_timer,
+MACHINE_END
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 21/23] Add minimal support for DevKit8000
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Thomas Weber <weber@corscience.de>
These patches add board support for the Timll DevKit8000.
The DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 4
arch/arm/mach-omap2/Makefile | 2
arch/arm/mach-omap2/board-devkit8000.c | 691 ++++++++++++++++++++++++++++++++
3 files changed, 697 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-omap2/board-devkit8000.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 2e81a6e..a8a3d1e 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -58,6 +58,10 @@ config MACH_OMAP3_BEAGLE
depends on ARCH_OMAP3
select OMAP_PACKAGE_CBB
+config MACH_DEVKIT8000
+ bool "DEVKIT8000 board"
+ depends on ARCH_OMAP3
+
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index dfc49a0..d3e54da 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -91,6 +91,8 @@ obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o \
obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \
hsmmc.o
+obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o \
+ hsmmc.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o \
hsmmc.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o \
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
new file mode 100644
index 0000000..89a55f1
--- /dev/null
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -0,0 +1,691 @@
+/*
+ * board-devkit8000.c - TimLL Devkit8000
+ *
+ * Copyright (C) 2009 Kim Botherway
+ * Copyright (C) 2010 Thomas Weber
+ *
+ * Modified from mach-omap2/board-omap3beagle.c
+ *
+ * Initial code: Syed Mohammed Khasim
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
+#include <plat/nand.h>
+#include <plat/usb.h>
+#include <plat/timer-gp.h>
+#include <plat/display.h>
+
+#include <plat/mcspi.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/usb/otg.h>
+#include <linux/dm9000.h>
+#include <linux/interrupt.h>
+
+#include "sdram-micron-mt46h32m32lf-6.h"
+
+#include "mux.h"
+#include "hsmmc.h"
+
+#define GPMC_CS0_BASE 0x60
+#define GPMC_CS_SIZE 0x30
+
+#define NAND_BLOCK_SIZE SZ_128K
+
+#define OMAP_DM9000_GPIO_IRQ 25
+#define OMAP3_DEVKIT_TS_GPIO 27
+
+static struct mtd_partition devkit8000_nand_partitions[] = {
+ /* All the partition sizes are listed in terms of NAND block size */
+ {
+ .name = "X-Loader",
+ .offset = 0,
+ .size = 4 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
+ .size = 15 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot Env",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
+ .size = 1 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "Kernel",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
+ .size = 32 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "File System",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct omap_nand_platform_data devkit8000_nand_data = {
+ .options = NAND_BUSWIDTH_16,
+ .parts = devkit8000_nand_partitions,
+ .nr_parts = ARRAY_SIZE(devkit8000_nand_partitions),
+ .dma_channel = -1, /* disable DMA in OMAP NAND driver */
+};
+
+static struct resource devkit8000_nand_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device devkit8000_nand_device = {
+ .name = "omap2-nand",
+ .id = -1,
+ .dev = {
+ .platform_data = &devkit8000_nand_data,
+ },
+ .num_resources = 1,
+ .resource = &devkit8000_nand_resource,
+};
+
+static struct omap2_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ .wires = 8,
+ .gpio_wp = 29,
+ },
+ {} /* Terminator */
+};
+static struct omap_board_config_kernel devkit8000_config[] __initdata = {
+};
+
+static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
+{
+ twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
+ twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
+
+ return 0;
+}
+
+static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
+{
+}
+static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
+{
+ return 0;
+}
+
+static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
+{
+}
+
+static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
+{
+
+ return 0;
+}
+
+static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
+{
+}
+
+
+static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+static struct regulator_consumer_supply devkit8000_vsim_supply = {
+ .supply = "vmmc_aux",
+};
+
+
+static struct omap_dss_device devkit8000_lcd_device = {
+ .name = "lcd",
+ .driver_name = "innolux_at_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .platform_enable = devkit8000_panel_enable_lcd,
+ .platform_disable = devkit8000_panel_disable_lcd,
+};
+static struct omap_dss_device devkit8000_dvi_device = {
+ .name = "dvi",
+ .driver_name = "generic_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .platform_enable = devkit8000_panel_enable_dvi,
+ .platform_disable = devkit8000_panel_disable_dvi,
+};
+
+static struct omap_dss_device devkit8000_tv_device = {
+ .name = "tv",
+ .driver_name = "venc",
+ .type = OMAP_DISPLAY_TYPE_VENC,
+ .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
+ .platform_enable = devkit8000_panel_enable_tv,
+ .platform_disable = devkit8000_panel_disable_tv,
+};
+
+
+static struct omap_dss_device *devkit8000_dss_devices[] = {
+ &devkit8000_lcd_device,
+ &devkit8000_dvi_device,
+ &devkit8000_tv_device,
+};
+
+static struct omap_dss_board_info devkit8000_dss_data = {
+ .num_devices = ARRAY_SIZE(devkit8000_dss_devices),
+ .devices = devkit8000_dss_devices,
+ .default_device = &devkit8000_lcd_device,
+};
+
+static struct platform_device devkit8000_dss_device = {
+ .name = "omapdss",
+ .id = -1,
+ .dev = {
+ .platform_data = &devkit8000_dss_data,
+ },
+};
+
+static struct regulator_consumer_supply devkit8000_vdda_dac_supply = {
+ .supply = "vdda_dac",
+ .dev = &devkit8000_dss_device.dev,
+};
+
+static int board_keymap[] = {
+ KEY(0, 0, KEY_1),
+ KEY(1, 0, KEY_2),
+ KEY(2, 0, KEY_3),
+ KEY(0, 1, KEY_4),
+ KEY(1, 1, KEY_5),
+ KEY(2, 1, KEY_6),
+ KEY(3, 1, KEY_F5),
+ KEY(0, 2, KEY_7),
+ KEY(1, 2, KEY_8),
+ KEY(2, 2, KEY_9),
+ KEY(3, 2, KEY_F6),
+ KEY(0, 3, KEY_F7),
+ KEY(1, 3, KEY_0),
+ KEY(2, 3, KEY_F8),
+ PERSISTENT_KEY(4, 5),
+ KEY(4, 4, KEY_VOLUMEUP),
+ KEY(5, 5, KEY_VOLUMEDOWN),
+ 0
+};
+
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
+static struct twl4030_keypad_data devkit8000_kp_data = {
+ .keymap_data = &board_map_data,
+ .rows = 6,
+ .cols = 6,
+ .rep = 1,
+};
+
+static struct gpio_led gpio_leds[];
+
+static int devkit8000_twl_gpio_setup(struct device *dev,
+ unsigned gpio, unsigned ngpio)
+{
+ omap_mux_init_gpio(29, OMAP_PIN_INPUT);
+ /* gpio + 0 is "mmc0_cd" (input/IRQ) */
+ mmc[0].gpio_cd = gpio + 0;
+ omap2_hsmmc_init(mmc);
+
+ /* link regulators to MMC adapters */
+ devkit8000_vmmc1_supply.dev = mmc[0].dev;
+ devkit8000_vsim_supply.dev = mmc[0].dev;
+
+ /* REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+
+ gpio_request(gpio + 1, "EHCI_nOC");
+ gpio_direction_input(gpio + 1);
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
+ gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
+ gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
+
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+ return 0;
+}
+
+static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+ .irq_base = TWL4030_GPIO_IRQ_BASE,
+ .irq_end = TWL4030_GPIO_IRQ_END,
+ .use_leds = true,
+ .pullups = BIT(1),
+ .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
+ | BIT(15) | BIT(16) | BIT(17),
+ .setup = devkit8000_twl_gpio_setup,
+};
+
+static struct regulator_consumer_supply devkit8000_vpll2_supplies[] = {
+ {
+ .supply = "vdvi",
+ .dev = &devkit8000_lcd_device.dev,
+ },
+ {
+ .supply = "vdss_dsi",
+ .dev = &devkit8000_dss_device.dev,
+ }
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data devkit8000_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vmmc1_supply,
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data devkit8000_vsim = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vsim_supply,
+};
+
+/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
+static struct regulator_init_data devkit8000_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &devkit8000_vdda_dac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data devkit8000_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(devkit8000_vpll2_supplies),
+ .consumer_supplies = devkit8000_vpll2_supplies,
+};
+
+static struct twl4030_usb_data devkit8000_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
+static struct twl4030_codec_audio_data devkit8000_audio_data = {
+ .audio_mclk = 26000000,
+};
+
+static struct twl4030_codec_data devkit8000_codec_data = {
+ .audio_mclk = 26000000,
+ .audio = &devkit8000_audio_data,
+};
+
+static struct twl4030_platform_data devkit8000_twldata = {
+ .irq_base = TWL4030_IRQ_BASE,
+ .irq_end = TWL4030_IRQ_END,
+
+ /* platform_data for children goes here */
+ .usb = &devkit8000_usb_data,
+ .gpio = &devkit8000_gpio_data,
+ .codec = &devkit8000_codec_data,
+ .vmmc1 = &devkit8000_vmmc1,
+ .vsim = &devkit8000_vsim,
+ .vdac = &devkit8000_vdac,
+ .vpll2 = &devkit8000_vpll2,
+ .keypad = &devkit8000_kp_data,
+};
+
+static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("twl4030", 0x48),
+ .flags = I2C_CLIENT_WAKE,
+ .irq = INT_34XX_SYS_NIRQ,
+ .platform_data = &devkit8000_twldata,
+ },
+};
+
+static int __init devkit8000_i2c_init(void)
+{
+ omap_register_i2c_bus(1, 2600, devkit8000_i2c_boardinfo,
+ ARRAY_SIZE(devkit8000_i2c_boardinfo));
+ /* Bus 3 is attached to the DVI port where devices like the pico DLP
+ * projector don't work reliably with 400kHz */
+ omap_register_i2c_bus(3, 400, NULL, 0);
+ return 0;
+}
+
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "led1",
+ .default_trigger = "heartbeat",
+ .gpio = 186,
+ .active_low = true,
+ },
+ {
+ .name = "led2",
+ .default_trigger = "mmc0",
+ .gpio = 163,
+ .active_low = true,
+ },
+ {
+ .name = "ledB",
+ .default_trigger = "none",
+ .gpio = 153,
+ .active_low = true,
+ },
+ {
+ .name = "led3",
+ .default_trigger = "none",
+ .gpio = 164,
+ .active_low = true,
+ },
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_led_info,
+ },
+};
+
+static struct gpio_keys_button gpio_buttons[] = {
+ {
+ .code = BTN_EXTRA,
+ .gpio = 26,
+ .desc = "user",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data gpio_key_info = {
+ .buttons = gpio_buttons,
+ .nbuttons = ARRAY_SIZE(gpio_buttons),
+};
+
+static struct platform_device keys_gpio = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_key_info,
+ },
+};
+
+
+static void __init devkit8000_init_irq(void)
+{
+ omap_board_config = devkit8000_config;
+ omap_board_config_size = ARRAY_SIZE(devkit8000_config);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
+ omap_init_irq();
+#ifdef CONFIG_OMAP_32K_TIMER
+ omap2_gp_clockevent_set_gptimer(12);
+#endif
+ omap_gpio_init();
+}
+
+static void __init devkit8000_ads7846_init(void)
+{
+ int gpio = OMAP3_DEVKIT_TS_GPIO;
+ int ret;
+
+ ret = gpio_request(gpio, "ads7846_pen_down");
+ if (ret < 0) {
+ printk(KERN_ERR "Failed to request GPIO %d for "
+ "ads7846 pen down IRQ\n", gpio);
+ return;
+ }
+
+ gpio_direction_input(gpio);
+}
+
+static int ads7846_get_pendown_state(void)
+{
+ return !gpio_get_value(OMAP3_DEVKIT_TS_GPIO);
+}
+
+static struct ads7846_platform_data ads7846_config = {
+ .x_max = 0x0fff,
+ .y_max = 0x0fff,
+ .x_plate_ohms = 180,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 5,
+ .debounce_rep = 1,
+ .get_pendown_state = ads7846_get_pendown_state,
+ .keep_vref_on = 1,
+ .settle_delay_usecs = 150,
+};
+
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info devkit8000_spi_board_info[] __initdata = {
+ {
+ .modalias = "ads7846",
+ .bus_num = 2,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &ads7846_mcspi_config,
+ .irq = OMAP_GPIO_IRQ(OMAP3_DEVKIT_TS_GPIO),
+ .platform_data = &ads7846_config,
+ }
+};
+
+#define OMAP_DM9000_BASE 0x2c000000
+
+static struct resource omap_dm9000_resources[] = {
+ [0] = {
+ .start = OMAP_DM9000_BASE,
+ .end = (OMAP_DM9000_BASE + 0x4 - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = (OMAP_DM9000_BASE + 0x400),
+ .end = (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = OMAP_GPIO_IRQ(OMAP_DM9000_GPIO_IRQ),
+ .flags = IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
+ },
+};
+
+static struct dm9000_plat_data omap_dm9000_platdata = {
+ .flags = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device omap_dm9000_dev = {
+ .name = "dm9000",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(omap_dm9000_resources),
+ .resource = omap_dm9000_resources,
+ .dev = {
+ .platform_data = &omap_dm9000_platdata,
+ },
+};
+
+static void __init omap_dm9000_init(void)
+{
+ if (gpio_request(OMAP_DM9000_GPIO_IRQ, "dm9000 irq") < 0) {
+ printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
+ OMAP_DM9000_GPIO_IRQ);
+ return;
+ }
+
+ gpio_direction_input(OMAP_DM9000_GPIO_IRQ);
+}
+
+static struct platform_device *devkit8000_devices[] __initdata = {
+ &devkit8000_dss_device,
+ &leds_gpio,
+ &keys_gpio,
+ &omap_dm9000_dev,
+};
+
+static void __init devkit8000_flash_init(void)
+{
+ u8 cs = 0;
+ u8 nandcs = GPMC_CS_NUM + 1;
+
+ u32 gpmc_base_add = OMAP34XX_GPMC_VIRT;
+
+ /* find out the chip-select on which NAND exists */
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ if ((ret & 0xC00) == 0x800) {
+ printk(KERN_INFO "Found NAND on CS%d\n", cs);
+ if (nandcs > GPMC_CS_NUM)
+ nandcs = cs;
+ }
+ cs++;
+ }
+
+ if (nandcs > GPMC_CS_NUM) {
+ printk(KERN_INFO "NAND: Unable to find configuration "
+ "in GPMC\n ");
+ return;
+ }
+
+ if (nandcs < GPMC_CS_NUM) {
+ devkit8000_nand_data.cs = nandcs;
+ devkit8000_nand_data.gpmc_cs_baseaddr = (void *)
+ (gpmc_base_add + GPMC_CS0_BASE + nandcs * GPMC_CS_SIZE);
+ devkit8000_nand_data.gpmc_baseaddr = (void *)
+ (gpmc_base_add);
+
+ printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
+ if (platform_device_register(&devkit8000_nand_device) < 0)
+ printk(KERN_ERR "Unable to register NAND device\n");
+ }
+}
+
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 147,
+ .reset_gpio_port[2] = -EINVAL
+};
+
+static void __init devkit8000_init(void)
+{
+ devkit8000_i2c_init();
+ platform_add_devices(devkit8000_devices,
+ ARRAY_SIZE(devkit8000_devices));
+ omap_board_config = devkit8000_config;
+ omap_board_config_size = ARRAY_SIZE(devkit8000_config);
+
+ spi_register_board_info(devkit8000_spi_board_info,
+ ARRAY_SIZE(devkit8000_spi_board_info));
+
+ omap_serial_init();
+
+ omap_dm9000_init();
+
+ devkit8000_ads7846_init();
+
+ omap_mux_init_gpio(170, OMAP_PIN_INPUT);
+
+ gpio_request(170, "DVI_nPD");
+ /* REVISIT leave DVI powered down until it's needed ... */
+ gpio_direction_output(170, true);
+
+ usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
+ devkit8000_flash_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
+}
+
+static void __init devkit8000_map_io(void)
+{
+ omap2_set_globals_343x();
+ omap34xx_map_common_io();
+}
+
+MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = devkit8000_map_io,
+ .init_irq = devkit8000_init_irq,
+ .init_machine = devkit8000_init,
+ .timer = &omap_timer,
+MACHINE_END
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 22/23] Add devkit8000_defconfig
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: Thomas Weber, linux-omap
From: Thomas Weber <weber@corscience.de>
This patch adds a default config for the Timll Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/devkit8000_defconfig | 1889 +++++++++++++++++++++++++++++++++
1 files changed, 1889 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/configs/devkit8000_defconfig
diff --git a/arch/arm/configs/devkit8000_defconfig b/arch/arm/configs/devkit8000_defconfig
new file mode 100644
index 0000000..61a817e
--- /dev/null
+++ b/arch/arm/configs/devkit8000_defconfig
@@ -0,0 +1,1889 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.33-rc6
+# Thu Feb 4 15:42:56 2010
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+# CONFIG_RD_LZO is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+CONFIG_ARCH_OMAP=y
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
+
+#
+# TI OMAP Implementations
+#
+CONFIG_ARCH_OMAP_OTG=y
+# CONFIG_ARCH_OMAP1 is not set
+CONFIG_ARCH_OMAP2PLUS=y
+# CONFIG_ARCH_OMAP2 is not set
+CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
+
+#
+# OMAP Feature Selections
+#
+# CONFIG_OMAP_RESET_CLOCKS is not set
+# CONFIG_OMAP_MUX is not set
+CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
+# CONFIG_OMAP_MPU_TIMER is not set
+CONFIG_OMAP_32K_TIMER=y
+CONFIG_OMAP_32K_TIMER_HZ=128
+CONFIG_OMAP_DM_TIMER=y
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
+CONFIG_ARCH_OMAP3430=y
+
+#
+# OMAP Board Type
+#
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+CONFIG_MACH_DEVKIT8000=y
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+# CONFIG_MACH_CM_T35 is not set
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_HAS_TLS_REG=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+# CONFIG_LEDS is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS2,115200n8 root=/dev/nfs nfsroot=192.168.1.1:home/nfsroot/current,home/nfsroot/current ip=dhcp rw noinitrd root delay=3"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_NEON=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+CONFIG_IRDA=y
+
+#
+# IrDA protocols
+#
+# CONFIG_IRLAN is not set
+# CONFIG_IRCOMM is not set
+# CONFIG_IRDA_ULTRA is not set
+
+#
+# IrDA options
+#
+# CONFIG_IRDA_CACHE_LAST_LSAP is not set
+# CONFIG_IRDA_FAST_RR is not set
+# CONFIG_IRDA_DEBUG is not set
+
+#
+# Infrared-port device drivers
+#
+
+#
+# SIR device drivers
+#
+# CONFIG_IRTTY_SIR is not set
+
+#
+# Dongle support
+#
+# CONFIG_KINGSUN_DONGLE is not set
+# CONFIG_KSDAZZLE_DONGLE is not set
+# CONFIG_KS959_DONGLE is not set
+
+#
+# FIR device drivers
+#
+# CONFIG_USB_IRDA is not set
+# CONFIG_SIGMATEL_FIR is not set
+# CONFIG_MCS_FIR is not set
+CONFIG_BT=y
+# CONFIG_BT_L2CAP is not set
+# CONFIG_BT_SCO is not set
+
+#
+# Bluetooth device drivers
+#
+# CONFIG_BT_HCIBTUSB is not set
+# CONFIG_BT_HCIBTSDIO is not set
+# CONFIG_BT_HCIUART is not set
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_BT_MRVL is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=40960
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL=y
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+CONFIG_KEYBOARD_MATRIX=y
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_TWL4030=y
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=y
+# CONFIG_SERIO_ALTERA_PS2 is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=32
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_MAX_RAW_DEVS=256
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_OMAP=y
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
+# CONFIG_GPIO_ADP5588 is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+CONFIG_MFD_CORE=y
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+CONFIG_TWL4030_CORE=y
+CONFIG_TWL4030_POWER=y
+CONFIG_TWL4030_CODEC=y
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+CONFIG_FB_FOREIGN_ENDIAN=y
+CONFIG_FB_BOTH_ENDIAN=y
+# CONFIG_FB_BIG_ENDIAN is not set
+# CONFIG_FB_LITTLE_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_FB_OMAP_BOOTLOADER_INIT=y
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=0
+CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
+# CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+CONFIG_OMAP2_DSS_VENC=y
+# CONFIG_OMAP2_DSS_SDI is not set
+# CONFIG_OMAP2_DSS_DSI is not set
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+CONFIG_PANEL_GENERIC=y
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+CONFIG_PANEL_INNOLUX_AT070TN83=y
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE is not set
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
+# CONFIG_SND_MIXER_OSS is not set
+# CONFIG_SND_PCM_OSS is not set
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_MCBSP=y
+CONFIG_SND_OMAP_SOC_OMAP3_BEAGLE=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_TWL4030=y
+# CONFIG_SOUND_PRIME is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+CONFIG_HIDRAW=y
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_HID_PID is not set
+CONFIG_USB_HIDDEV=y
+
+#
+# Special HID drivers
+#
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+# CONFIG_HID_DRAGONRISE is not set
+CONFIG_HID_EZKEY=y
+# CONFIG_HID_KYE is not set
+CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+# CONFIG_HID_NTRIG is not set
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+CONFIG_USB_MON=y
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_SOC=y
+
+#
+# OMAP 343x high speed USB support
+#
+CONFIG_USB_MUSB_HOST=y
+# CONFIG_USB_MUSB_PERIPHERAL is not set
+# CONFIG_USB_MUSB_OTG is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+CONFIG_USB_MUSB_HDRC_HCD=y
+# CONFIG_MUSB_PIO_ONLY is not set
+CONFIG_USB_INVENTRA_DMA=y
+# CONFIG_USB_TI_CPPI_DMA is not set
+# CONFIG_USB_MUSB_DEBUG is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+CONFIG_USB_GADGET_OMAP=y
+CONFIG_USB_OMAP=y
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+# CONFIG_USB_ZERO is not set
+CONFIG_USB_AUDIO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_GADGETFS=m
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+CONFIG_USB_G_PRINTER=m
+# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_MULTI is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+# CONFIG_USB_ULPI is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=m
+# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+CONFIG_MMC_SPI=m
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_REGULATOR is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+CONFIG_RTC_DRV_TWL4030=y
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
+
+#
+# CBUS support
+#
+# CONFIG_CBUS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+# CONFIG_EXT3_FS_XATTR is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_QUOTA=y
+# CONFIG_QUOTA_NETLINK_INTERFACE is not set
+CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
+# CONFIG_QFMT_V1 is not set
+CONFIG_QFMT_V2=y
+CONFIG_QUOTACTL=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=1
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_ERRORS=y
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=m
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32=y
+CONFIG_CRC7=m
+CONFIG_LIBCRC32C=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 22/23] Add devkit8000_defconfig
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Thomas Weber <weber@corscience.de>
This patch adds a default config for the Timll Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/devkit8000_defconfig | 1889 +++++++++++++++++++++++++++++++++
1 files changed, 1889 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/configs/devkit8000_defconfig
diff --git a/arch/arm/configs/devkit8000_defconfig b/arch/arm/configs/devkit8000_defconfig
new file mode 100644
index 0000000..61a817e
--- /dev/null
+++ b/arch/arm/configs/devkit8000_defconfig
@@ -0,0 +1,1889 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.33-rc6
+# Thu Feb 4 15:42:56 2010
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
+# CONFIG_KERNEL_LZO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_TINY_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+# CONFIG_RD_LZO is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_INLINE_SPIN_TRYLOCK is not set
+# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK is not set
+# CONFIG_INLINE_SPIN_LOCK_BH is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQ is not set
+# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set
+CONFIG_INLINE_SPIN_UNLOCK=y
+# CONFIG_INLINE_SPIN_UNLOCK_BH is not set
+CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
+# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_READ_TRYLOCK is not set
+# CONFIG_INLINE_READ_LOCK is not set
+# CONFIG_INLINE_READ_LOCK_BH is not set
+# CONFIG_INLINE_READ_LOCK_IRQ is not set
+# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set
+CONFIG_INLINE_READ_UNLOCK=y
+# CONFIG_INLINE_READ_UNLOCK_BH is not set
+CONFIG_INLINE_READ_UNLOCK_IRQ=y
+# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set
+# CONFIG_INLINE_WRITE_TRYLOCK is not set
+# CONFIG_INLINE_WRITE_LOCK is not set
+# CONFIG_INLINE_WRITE_LOCK_BH is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQ is not set
+# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set
+CONFIG_INLINE_WRITE_UNLOCK=y
+# CONFIG_INLINE_WRITE_UNLOCK_BH is not set
+CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
+# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set
+# CONFIG_MUTEX_SPIN_ON_OWNER is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_DOVE is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+CONFIG_ARCH_OMAP=y
+# CONFIG_ARCH_BCMRING is not set
+# CONFIG_ARCH_U8500 is not set
+
+#
+# TI OMAP Implementations
+#
+CONFIG_ARCH_OMAP_OTG=y
+# CONFIG_ARCH_OMAP1 is not set
+CONFIG_ARCH_OMAP2PLUS=y
+# CONFIG_ARCH_OMAP2 is not set
+CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
+
+#
+# OMAP Feature Selections
+#
+# CONFIG_OMAP_RESET_CLOCKS is not set
+# CONFIG_OMAP_MUX is not set
+CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
+# CONFIG_OMAP_MPU_TIMER is not set
+CONFIG_OMAP_32K_TIMER=y
+CONFIG_OMAP_32K_TIMER_HZ=128
+CONFIG_OMAP_DM_TIMER=y
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
+CONFIG_ARCH_OMAP3430=y
+
+#
+# OMAP Board Type
+#
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+CONFIG_MACH_DEVKIT8000=y
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
+# CONFIG_MACH_OMAP3_TOUCHBOOK is not set
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+# CONFIG_MACH_CM_T35 is not set
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+# CONFIG_OMAP3_EMU is not set
+# CONFIG_OMAP3_SDRC_AC_TIMING is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_HAS_TLS_REG=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+# CONFIG_LEDS is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS2,115200n8 root=/dev/nfs nfsroot=192.168.1.1:home/nfsroot/current,home/nfsroot/current ip=dhcp rw noinitrd root delay=3"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_NEON=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+CONFIG_IRDA=y
+
+#
+# IrDA protocols
+#
+# CONFIG_IRLAN is not set
+# CONFIG_IRCOMM is not set
+# CONFIG_IRDA_ULTRA is not set
+
+#
+# IrDA options
+#
+# CONFIG_IRDA_CACHE_LAST_LSAP is not set
+# CONFIG_IRDA_FAST_RR is not set
+# CONFIG_IRDA_DEBUG is not set
+
+#
+# Infrared-port device drivers
+#
+
+#
+# SIR device drivers
+#
+# CONFIG_IRTTY_SIR is not set
+
+#
+# Dongle support
+#
+# CONFIG_KINGSUN_DONGLE is not set
+# CONFIG_KSDAZZLE_DONGLE is not set
+# CONFIG_KS959_DONGLE is not set
+
+#
+# FIR device drivers
+#
+# CONFIG_USB_IRDA is not set
+# CONFIG_SIGMATEL_FIR is not set
+# CONFIG_MCS_FIR is not set
+CONFIG_BT=y
+# CONFIG_BT_L2CAP is not set
+# CONFIG_BT_SCO is not set
+
+#
+# Bluetooth device drivers
+#
+# CONFIG_BT_HCIBTUSB is not set
+# CONFIG_BT_HCIBTSDIO is not set
+# CONFIG_BT_HCIUART is not set
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_BT_MRVL is not set
+# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_LIB80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+
+#
+# DRBD disabled because PROC_FS, INET or CONNECTOR not selected
+#
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=40960
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+# CONFIG_CHR_DEV_SG is not set
+# CONFIG_CHR_DEV_SCH is not set
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL=y
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+# CONFIG_INPUT_SPARSEKMAP is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+CONFIG_KEYBOARD_MATRIX=y
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_TWL4030=y
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_DYNAPRO is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=y
+# CONFIG_SERIO_ALTERA_PS2 is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=32
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+CONFIG_RAW_DRIVER=y
+CONFIG_MAX_RAW_DEVS=256
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_OMAP=y
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_OMAP24XX=y
+# CONFIG_SPI_XILINX is not set
+# CONFIG_SPI_DESIGNWARE is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
+# CONFIG_GPIO_ADP5588 is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+CONFIG_MFD_CORE=y
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+CONFIG_TWL4030_CORE=y
+CONFIG_TWL4030_POWER=y
+CONFIG_TWL4030_CODEC=y
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MFD_88PM8607 is not set
+# CONFIG_AB4500_CORE is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+CONFIG_FB_FOREIGN_ENDIAN=y
+CONFIG_FB_BOTH_ENDIAN=y
+# CONFIG_FB_BIG_ENDIAN is not set
+# CONFIG_FB_LITTLE_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_TMIO is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_FB_OMAP_BOOTLOADER_INIT=y
+CONFIG_OMAP2_VRAM=y
+CONFIG_OMAP2_VRFB=y
+CONFIG_OMAP2_DSS=y
+CONFIG_OMAP2_VRAM_SIZE=0
+CONFIG_OMAP2_DSS_DEBUG_SUPPORT=y
+# CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS is not set
+# CONFIG_OMAP2_DSS_RFBI is not set
+CONFIG_OMAP2_DSS_VENC=y
+# CONFIG_OMAP2_DSS_SDI is not set
+# CONFIG_OMAP2_DSS_DSI is not set
+# CONFIG_OMAP2_DSS_FAKE_VSYNC is not set
+CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=0
+CONFIG_FB_OMAP2=y
+CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
+# CONFIG_FB_OMAP2_FORCE_AUTO_UPDATE is not set
+CONFIG_FB_OMAP2_NUM_FBS=3
+
+#
+# OMAP2/3 Display Device Drivers
+#
+CONFIG_PANEL_GENERIC=y
+# CONFIG_PANEL_SHARP_LS037V7DW01 is not set
+CONFIG_PANEL_INNOLUX_AT070TN83=y
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE is not set
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
+# CONFIG_SND_MIXER_OSS is not set
+# CONFIG_SND_PCM_OSS is not set
+# CONFIG_SND_HRTIMER is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+CONFIG_SND_ARM=y
+CONFIG_SND_SPI=y
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_MCBSP=y
+CONFIG_SND_OMAP_SOC_OMAP3_BEAGLE=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_TWL4030=y
+# CONFIG_SOUND_PRIME is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+CONFIG_HIDRAW=y
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_HID_PID is not set
+CONFIG_USB_HIDDEV=y
+
+#
+# Special HID drivers
+#
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+# CONFIG_HID_DRAGONRISE is not set
+CONFIG_HID_EZKEY=y
+# CONFIG_HID_KYE is not set
+CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+# CONFIG_HID_NTRIG is not set
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+CONFIG_USB_MON=y
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_SOC=y
+
+#
+# OMAP 343x high speed USB support
+#
+CONFIG_USB_MUSB_HOST=y
+# CONFIG_USB_MUSB_PERIPHERAL is not set
+# CONFIG_USB_MUSB_OTG is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+CONFIG_USB_MUSB_HDRC_HCD=y
+# CONFIG_MUSB_PIO_ONLY is not set
+CONFIG_USB_INVENTRA_DMA=y
+# CONFIG_USB_TI_CPPI_DMA is not set
+# CONFIG_USB_MUSB_DEBUG is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+CONFIG_USB_GADGET_OMAP=y
+CONFIG_USB_OMAP=y
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+# CONFIG_USB_ZERO is not set
+CONFIG_USB_AUDIO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_ETH_EEM=y
+CONFIG_USB_GADGETFS=m
+# CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+CONFIG_USB_G_PRINTER=m
+# CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_MULTI is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+# CONFIG_USB_ULPI is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=m
+# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+CONFIG_MMC_SPI=m
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_REGULATOR is not set
+# CONFIG_LEDS_BD2802 is not set
+# CONFIG_LEDS_LT3593 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+CONFIG_RTC_DRV_TWL4030=y
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_MSM6242 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_RP5C01 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
+# CONFIG_STAGING is not set
+
+#
+# CBUS support
+#
+# CONFIG_CBUS is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+# CONFIG_EXT3_FS_XATTR is not set
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_QUOTA=y
+# CONFIG_QUOTA_NETLINK_INTERFACE is not set
+CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
+# CONFIG_QFMT_V1 is not set
+CONFIG_QFMT_V2=y
+CONFIG_QUOTACTL=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=1
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_ERRORS=y
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+# CONFIG_OC_ETM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_DEFAULT_SECURITY_SELINUX is not set
+# CONFIG_DEFAULT_SECURITY_SMACK is not set
+# CONFIG_DEFAULT_SECURITY_TOMOYO is not set
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_DEFAULT_SECURITY=""
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=m
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32=y
+CONFIG_CRC7=m
+CONFIG_LIBCRC32C=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 23/23] OMAP3EVM: PM: Update defconfig
2010-02-18 1:31 ` Tony Lindgren
@ 2010-02-18 1:32 ` Tony Lindgren
-1 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel; +Cc: linux-omap, Sanjeev Premi
From: Sanjeev Premi <premi@ti.com>
This patch updates the omap3_evm_defconfig to
select these options:
* CONFIG_PM_DEBUG
* CONFIG_DEBUG_FS
* CONFIG_OMAP_SMARTREFLEX
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/omap3_evm_defconfig | 6 ++++--
1 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig
index 86cc4be..e2ad859 100644
--- a/arch/arm/configs/omap3_evm_defconfig
+++ b/arch/arm/configs/omap3_evm_defconfig
@@ -187,6 +187,8 @@ CONFIG_ARCH_OMAP3=y
#
# OMAP Feature Selections
#
+CONFIG_OMAP_SMARTREFLEX=y
+# CONFIG_OMAP_SMARTREFLEX_TESTING is not set
# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
CONFIG_OMAP_RESET_CLOCKS=y
@@ -333,7 +335,7 @@ CONFIG_BINFMT_MISC=y
# Power management options
#
CONFIG_PM=y
-# CONFIG_PM_DEBUG is not set
+CONFIG_PM_DEBUG=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
@@ -1339,7 +1341,7 @@ CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH 23/23] OMAP3EVM: PM: Update defconfig
@ 2010-02-18 1:32 ` Tony Lindgren
0 siblings, 0 replies; 48+ messages in thread
From: Tony Lindgren @ 2010-02-18 1:32 UTC (permalink / raw)
To: linux-arm-kernel
From: Sanjeev Premi <premi@ti.com>
This patch updates the omap3_evm_defconfig to
select these options:
* CONFIG_PM_DEBUG
* CONFIG_DEBUG_FS
* CONFIG_OMAP_SMARTREFLEX
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/omap3_evm_defconfig | 6 ++++--
1 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig
index 86cc4be..e2ad859 100644
--- a/arch/arm/configs/omap3_evm_defconfig
+++ b/arch/arm/configs/omap3_evm_defconfig
@@ -187,6 +187,8 @@ CONFIG_ARCH_OMAP3=y
#
# OMAP Feature Selections
#
+CONFIG_OMAP_SMARTREFLEX=y
+# CONFIG_OMAP_SMARTREFLEX_TESTING is not set
# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
CONFIG_OMAP_RESET_CLOCKS=y
@@ -333,7 +335,7 @@ CONFIG_BINFMT_MISC=y
# Power management options
#
CONFIG_PM=y
-# CONFIG_PM_DEBUG is not set
+CONFIG_PM_DEBUG=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
@@ -1339,7 +1341,7 @@ CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
^ permalink raw reply related [flat|nested] 48+ messages in thread
end of thread, other threads:[~2010-02-18 1:32 UTC | newest]
Thread overview: 48+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-02-18 1:31 [PATCH 00/23] Series short description Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren
2010-02-18 1:31 ` [PATCH 01/23] omap: zoom3: enable ehci support Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren
2010-02-18 1:31 ` [PATCH 02/23] omap3evm: Add mux settings for keypad Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren
2010-02-18 1:31 ` [PATCH 03/23] omap3evm: Fixes after moving to matrix_keypad Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren
2010-02-18 1:31 ` [PATCH 04/23] omap3evm: Configure GPIO175 for touchscreen PEN_IRQ Tony Lindgren
2010-02-18 1:31 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 05/23] OMAP: pandora: add DSS2 support and related regulators Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 06/23] omap3: pandora: update regulator setup Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 07/23] omap3: pandora: update defconfig Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 08/23] omap3: Add platform data for the twl4030_codec MFD on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 09/23] omap3: Fix typo on IGEP v2 board Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 10/23] omap3: Add platform init code for EHCI driver on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 11/23] omap3: Enable DSS2 for IGEP v2 board Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 12/23] omap3: Add support for flash on " Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 13/23] ARM: OMAP3: SDRC: add timing data for Numonyx M65KxxxxAM Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 14/23] omap3: Use timing data for omap2_init_common_hw on IGEP v2 Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 15/23] omap3: Update defconfig for IGEP v2 to allow new drivers andfeatures Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 16/23] IGEPv2: Added WIFI support Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 17/23] IGEPv2: Use Red Led1 as Heartbeat if configured Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 18/23] AM3517: Enable basic I2C Support Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 19/23] AM3517: Enable RTC driver support for AM3517EVM Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 20/23] AM3517: Enable I2C-GPIO Expander " Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 21/23] Add minimal support for DevKit8000 Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 22/23] Add devkit8000_defconfig Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
2010-02-18 1:32 ` [PATCH 23/23] OMAP3EVM: PM: Update defconfig Tony Lindgren
2010-02-18 1:32 ` Tony Lindgren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.