All of lore.kernel.org
 help / color / mirror / Atom feed
* sata_sil: freeze on modprobe
@ 2010-05-28 18:38 Alessandro Zummo
  2010-05-28 23:55 ` Robert Hancock
  0 siblings, 1 reply; 3+ messages in thread
From: Alessandro Zummo @ 2010-05-28 18:38 UTC (permalink / raw)
  To: linux-ide


 I'm testing sata_sil with this controller:

00:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
00:0b.0 0104: 1095:3114 (rev 02)

 with two different hard disks. On modprobe there's an EH situation
 which freezes the task for several minutes. The device
 node is not even created. The module device count is incremented to 3.

 an echo 1 >rescan triggers the same situation again.

 I'm running on 2.6.34. 

 how can I help debugging?


sata_sil 0000:00:0b.0: version 2.4
sata_sil 0000:00:0b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
sata_sil 0000:00:0b.0: Applying R_ERR on DMA activate FIS errata fix
scsi4 : sata_sil
scsi5 : sata_sil
scsi6 : sata_sil
scsi7 : sata_sil
ata5: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00080 irq 16
ata6: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde000c0 irq 16
ata7: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00280 irq 16
ata8: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde002c0 irq 16
ata5: SATA link down (SStatus 0 SControl 310)
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: ATA-8: WDC WD2502ABYS-18B7A0, 02.03B04, max UDMA/133
ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata6.00: applying Seagate errata fix (mod15write workaround)
ata6.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access     ATA      WDC WD2502ABYS-1 02.0 PQ: 0 ANSI: 5
sd 5:0:0:0: Attached scsi generic sg2 type 0
sd 5:0:0:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc:
ata7: SATA link down (SStatus 0 SControl 310)
ata8: SATA link down (SStatus 0 SControl 310)
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/100
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/66:PIO4
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/66
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/33:PIO4
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
        72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 
        00 00 00 00 
sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
        72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 
        00 00 00 00 
sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
 unable to read partition table
ata6: EH complete
sdc: detected capacity change from 0 to 250000000000
sd 5:0:0:0: [sdc] Attached SCSI disk
sdc: detected capacity change from 0 to 250000000000


-- 

 Best regards,

 Alessandro Zummo,
  Tower Technologies - Torino, Italy

  http://www.towertech.it


^ permalink raw reply	[flat|nested] 3+ messages in thread
* Re: sata_sil: freeze on modprobe
  2010-05-28 18:38 sata_sil: freeze on modprobe Alessandro Zummo
@ 2010-05-28 23:55 ` Robert Hancock
  2010-05-29  6:45   ` Alessandro Zummo
  0 siblings, 1 reply; 3+ messages in thread
From: Robert Hancock @ 2010-05-28 23:55 UTC (permalink / raw)
  To: Alessandro Zummo; +Cc: linux-ide

On 05/28/2010 12:38 PM, Alessandro Zummo wrote:
>
>   I'm testing sata_sil with this controller:
>
> 00:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
> 00:0b.0 0104: 1095:3114 (rev 02)
>
>   with two different hard disks. On modprobe there's an EH situation
>   which freezes the task for several minutes. The device
>   node is not even created. The module device count is incremented to 3.
>
>   an echo 1>rescan triggers the same situation again.
>
>   I'm running on 2.6.34.
>
>   how can I help debugging?

What does /proc/interrupts show after this? It seems like you might be 
missing interrupts somehow.

>
>
> sata_sil 0000:00:0b.0: version 2.4
> sata_sil 0000:00:0b.0: PCI INT A ->  GSI 16 (level, low) ->  IRQ 16
> sata_sil 0000:00:0b.0: Applying R_ERR on DMA activate FIS errata fix
> scsi4 : sata_sil
> scsi5 : sata_sil
> scsi6 : sata_sil
> scsi7 : sata_sil
> ata5: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00080 irq 16
> ata6: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde000c0 irq 16
> ata7: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00280 irq 16
> ata8: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde002c0 irq 16
> ata5: SATA link down (SStatus 0 SControl 310)
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: ATA-8: WDC WD2502ABYS-18B7A0, 02.03B04, max UDMA/133
> ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32)
> ata6.00: applying Seagate errata fix (mod15write workaround)

This drive isn't in the mod15write blacklist - did you use the slow_down 
module parameter?

> ata6.00: configured for UDMA/100
> scsi 5:0:0:0: Direct-Access     ATA      WDC WD2502ABYS-1 02.0 PQ: 0 ANSI: 5
> sd 5:0:0:0: Attached scsi generic sg2 type 0
> sd 5:0:0:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
> sd 5:0:0:0: [sdc] Write Protect is off
> sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>   sdc:
> ata7: SATA link down (SStatus 0 SControl 310)
> ata8: SATA link down (SStatus 0 SControl 310)
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/100
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: limiting speed to UDMA/66:PIO4
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/66
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: limiting speed to UDMA/33:PIO4
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
> sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
>          72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
>          00 00 00 00
> sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
> sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
> end_request: I/O error, dev sdc, sector 0
> Buffer I/O error on device sdc, logical block 0
> Buffer I/O error on device sdc, logical block 1
> Buffer I/O error on device sdc, logical block 2
> Buffer I/O error on device sdc, logical block 3
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> ata6: EH complete
> ata6: drained 65536 bytes to clear DRQ.
> ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> ata6.00: failed command: READ DMA
> ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
>           res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> ata6.00: status: { DRDY }
> ata6: hard resetting link
> ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> ata6.00: configured for UDMA/33
> ata6.00: device reported invalid CHS sector 0
> sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
> sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
>          72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
>          00 00 00 00
> sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
> sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00
> end_request: I/O error, dev sdc, sector 0
> Buffer I/O error on device sdc, logical block 0
> Buffer I/O error on device sdc, logical block 1
> Buffer I/O error on device sdc, logical block 2
> Buffer I/O error on device sdc, logical block 3
>   unable to read partition table
> ata6: EH complete
> sdc: detected capacity change from 0 to 250000000000
> sd 5:0:0:0: [sdc] Attached SCSI disk
> sdc: detected capacity change from 0 to 250000000000
>
>


^ permalink raw reply	[flat|nested] 3+ messages in thread
* Re: sata_sil: freeze on modprobe
  2010-05-28 23:55 ` Robert Hancock
@ 2010-05-29  6:45   ` Alessandro Zummo
  0 siblings, 0 replies; 3+ messages in thread
From: Alessandro Zummo @ 2010-05-29  6:45 UTC (permalink / raw)
  To: Robert Hancock; +Cc: linux-ide

On Fri, 28 May 2010 17:55:43 -0600
Robert Hancock <hancockrwd@gmail.com> wrote:

> >   how can I help debugging?
> 
> What does /proc/interrupts show after this? It seems like you might be 
> missing interrupts somehow.

 I think you've got it, IRQs are not flowing.  
 16:          6   IO-APIC-fasteoi   sata_sil

 I'll check the BIOS and twiggle around with
 the slots.

> > ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32)
> > ata6.00: applying Seagate errata fix (mod15write workaround)
> 
> This drive isn't in the mod15write blacklist - did you use the slow_down 
> module parameter?

 yes, i tried both with and without.

 ty.

-- 

 Best regards,

 Alessandro Zummo,
  Tower Technologies - Torino, Italy

  http://www.towertech.it


^ permalink raw reply	[flat|nested] 3+ messages in thread
end of thread, other threads:[~2010-05-29  6:44 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-05-28 18:38 sata_sil: freeze on modprobe Alessandro Zummo
2010-05-28 23:55 ` Robert Hancock
2010-05-29  6:45   ` Alessandro Zummo

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.