* + nfc-driver-for-nxp-semiconductors-pn544-nfc-chip.patch added to -mm tree
@ 2010-10-29 21:35 akpm
0 siblings, 0 replies; only message in thread
From: akpm @ 2010-10-29 21:35 UTC (permalink / raw)
To: mm-commits; +Cc: matti.j.aaltonen
The patch titled
NFC: Driver for NXP Semiconductors PN544 NFC chip.
has been added to the -mm tree. Its filename is
nfc-driver-for-nxp-semiconductors-pn544-nfc-chip.patch
Before you just go and hit "reply", please:
a) Consider who else should be cc'ed
b) Prefer to cc a suitable mailing list as well
c) Ideally: find the original patch on the mailing list and do a
reply-to-all to that, adding suitable additional cc's
*** Remember to use Documentation/SubmitChecklist when testing your code ***
See http://userweb.kernel.org/~akpm/stuff/added-to-mm.txt to find
out what to do about this
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: NFC: Driver for NXP Semiconductors PN544 NFC chip.
From: "Matti J. Aaltonen" <matti.j.aaltonen@nokia.com>
Creates a new "Near Field Communication" subsystem in drivers/nfc.
http://en.wikipedia.org/wiki/Near_Field_Communication is useful ;)
This is a driver for the pn544 NFC device. The driver transfers
ETSI messages between the device and the user space.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
Documentation/nfc/nfc-pn544.txt | 105 +++
drivers/Kconfig | 2
drivers/Makefile | 2
drivers/nfc/Kconfig | 30 +
drivers/nfc/Makefile | 5
drivers/nfc/pn544.c | 893 ++++++++++++++++++++++++++++++
include/linux/nfc/pn544.h | 99 +++
7 files changed, 1135 insertions(+), 1 deletion(-)
diff -puN /dev/null Documentation/nfc/nfc-pn544.txt
--- /dev/null
+++ a/Documentation/nfc/nfc-pn544.txt
@@ -0,0 +1,105 @@
+Kernel driver for PN544
+========================
+
+* NXP Semiconductor PN544 Near Field Communication (NFC) chip
+
+Author: Jari Vanhala
+Contact: Matti Aaltonen (matti.j.aaltonen at nokia.com)
+
+Description
+-----------
+
+The PN544 is an integrated transmission module for contactless
+communication. The driver goes under drives/nfc/ and is compiled as a
+module named "pn544". It registers a misc device and creates a device
+file named "/dev/pn544".
+
+The driver, is quite simple and it mainly passes data between the
+hardware and the user space. There are two operating modes: The HCI
+(normal) mode and the firmware update mode. It can write and read in
+both modes. The hardware sends an interrupt when data is available
+for reading. Data is read when the read function is called by some
+user space application. Poll() checks the IRQ state. Configuration and
+self testing are done from the user space using read and write.
+
+The chip is powered up when the device is opened and otherwise
+it's turned off. Only one instance can use the device at a time.
+
+Host Interfaces: consisting of I2C, SPI and HSU as physical
+interfaces, this driver support I2C.
+
+The chip is controlled from the user spase by sending SWP/HCI (Single
+Wire Protocol) messages according to the ETSI/SCP standard, see
+http://www.etsi.org/WebSite/Technologies/ProtocolSpecification.aspx
+
+The driver handles two kinds of messages: the normal HCI messages and
+the firmware update messages. HCI messages consist of and eight bit
+header and the message body. The header contains the message length.
+Maximum size for an HCI message is 33. In HCI mode sent packets are
+tested for a correct CRC.
+
+Firmware update messages, which can be read and written in the
+firmware upload mode have the length in the second (MSB) and third
+(LSB) bytes of the message. The maximum FW message size is 1024
+bytes.
+
+The interfaces for pn544 users:
+
+There is a sysfs interface for testing that the hardware is
+operational. Reading from the sysfs file activates the test. The test
+returns one on success and zero on failure.
+
+Example:
+> cat /sys/module/pn544/drivers/i2c\:pn544/3-002b/nfc_test
+1
+
+For mode setting there is an IOCTL interface, which consists of
+two messages:
+
+PN544_GET_FW_MODE returns 1 if the device is in firmware
+update mode and zero in the normal (HCI) mode.
+
+PN544_SET_FW_MODE is for setting the mode. The message parameter
+value defines the mode: one corresponds firmware update and zero the
+HCI mode.
+
+
+Example platform data:
+
+static int rx71_pn544_nfc_request_resources(struct i2c_client *client)
+{
+ /* Get and setup the HW resources for the device */
+}
+
+static void rx71_pn544_nfc_free_resources(void)
+{
+ /* Release the HW resources */
+}
+
+static void rx71_pn544_nfc_enable(int fw)
+{
+ /* Turn the device on */
+}
+
+static int rx71_pn544_nfc_test(void)
+{
+ /*
+ * Put the device into the FW update mode
+ * and then back to the normal mode.
+ * Return one on success and zero on
+ * failure.
+ */
+}
+
+static void rx71_pn544_nfc_disable(void)
+{
+ /* turn the power off */
+}
+
+static struct pn544_nfc_platform_data rx71_nfc_data = {
+ .request_resources = rx71_pn544_nfc_request_resources,
+ .free_resources = rx71_pn544_nfc_free_resources,
+ .enable = rx71_pn544_nfc_enable,
+ .test = rx71_pn544_nfc_test,
+ .disable = rx71_pn544_nfc_disable,
+};
diff -puN drivers/Kconfig~nfc-driver-for-nxp-semiconductors-pn544-nfc-chip drivers/Kconfig
--- a/drivers/Kconfig~nfc-driver-for-nxp-semiconductors-pn544-nfc-chip
+++ a/drivers/Kconfig
@@ -111,4 +111,6 @@ source "drivers/xen/Kconfig"
source "drivers/staging/Kconfig"
source "drivers/platform/Kconfig"
+
+source "drivers/nfc/Kconfig"
endmenu
diff -puN drivers/Makefile~nfc-driver-for-nxp-semiconductors-pn544-nfc-chip drivers/Makefile
--- a/drivers/Makefile~nfc-driver-for-nxp-semiconductors-pn544-nfc-chip
+++ a/drivers/Makefile
@@ -39,7 +39,7 @@ obj-$(CONFIG_FB_INTEL) += video
obj-y += serial/
obj-$(CONFIG_PARPORT) += parport/
-obj-y += base/ block/ misc/ mfd/
+obj-y += base/ block/ misc/ mfd/ nfc/
obj-$(CONFIG_NUBUS) += nubus/
obj-y += macintosh/
obj-$(CONFIG_IDE) += ide/
diff -puN /dev/null drivers/nfc/Kconfig
--- /dev/null
+++ a/drivers/nfc/Kconfig
@@ -0,0 +1,30 @@
+#
+# Near Field Communication (NFC) devices
+#
+
+menuconfig NFC_DEVICES
+ bool "NFC devices"
+ default n
+ ---help---
+ You'll have to say Y if your computer contains an NFC device that
+ you want to use under Linux.
+
+ You can say N here if you don't have any Near Field Communication
+ devices connected to your computer.
+
+if NFC_DEVICES
+
+config PN544_NFC
+ tristate "PN544 NFC driver"
+ depends on I2C
+ select CRC_CCITT
+ default n
+ ---help---
+ Say yes if you want PN544 Near Field Communication driver.
+ This is for i2c connected version. If unsure, say N here.
+
+ To compile this driver as a module, choose m here. The module will
+ be called pn544.
+
+
+endif # NFC_DEVICES
diff -puN /dev/null drivers/nfc/Makefile
--- /dev/null
+++ a/drivers/nfc/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for nfc devices
+#
+
+obj-$(CONFIG_PN544_NFC) += pn544.o
diff -puN /dev/null drivers/nfc/pn544.c
--- /dev/null
+++ a/drivers/nfc/pn544.c
@@ -0,0 +1,893 @@
+/*
+ * Driver for the PN544 NFC chip.
+ *
+ * Copyright (C) Nokia Corporation
+ *
+ * Author: Jari Vanhala <ext-jari.vanhala@nokia.com>
+ * Contact: Matti Aaltonen <matti.j.aaltonen@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/completion.h>
+#include <linux/crc-ccitt.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/nfc/pn544.h>
+#include <linux/poll.h>
+#include <linux/regulator/consumer.h>
+#include <linux/serial_core.h> /* for TCGETS */
+#include <linux/slab.h>
+
+#define DRIVER_CARD "PN544 NFC"
+#define DRIVER_DESC "NFC driver for PN544"
+
+static struct i2c_device_id pn544_id_table[] = {
+ { PN544_DRIVER_NAME, 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, pn544_id_table);
+
+#define HCI_MODE 0
+#define FW_MODE 1
+
+enum pn544_state {
+ PN544_ST_COLD,
+ PN544_ST_FW_READY,
+ PN544_ST_READY,
+};
+
+enum pn544_irq {
+ PN544_NONE,
+ PN544_INT,
+};
+
+struct pn544_info {
+ struct miscdevice miscdev;
+ struct i2c_client *i2c_dev;
+ struct regulator_bulk_data regs[2];
+
+ enum pn544_state state;
+ wait_queue_head_t read_wait;
+ loff_t read_offset;
+ enum pn544_irq read_irq;
+ struct mutex read_mutex; /* Serialize read_irq access */
+ struct mutex mutex; /* Serialize info struct access */
+ u8 *buf;
+ unsigned int buflen;
+};
+
+static const char reg_vdd_io[] = "Vdd_IO";
+static const char reg_vbat[] = "VBat";
+
+/* sysfs interface */
+static ssize_t pn544_test(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct pn544_info *info = dev_get_drvdata(dev);
+ struct i2c_client *client = info->i2c_dev;
+ struct pn544_nfc_platform_data *pdata = client->dev.platform_data;
+
+ return snprintf(buf, PAGE_SIZE, "%d\n", pdata->test());
+}
+
+static int pn544_enable(struct pn544_info *info, int mode)
+{
+ struct pn544_nfc_platform_data *pdata;
+ struct i2c_client *client = info->i2c_dev;
+
+ int r;
+
+ r = regulator_bulk_enable(ARRAY_SIZE(info->regs), info->regs);
+ if (r < 0)
+ return r;
+
+ pdata = client->dev.platform_data;
+ info->read_irq = PN544_NONE;
+ if (pdata->enable)
+ pdata->enable(mode);
+
+ if (mode) {
+ info->state = PN544_ST_FW_READY;
+ dev_dbg(&client->dev, "now in FW-mode\n");
+ } else {
+ info->state = PN544_ST_READY;
+ dev_dbg(&client->dev, "now in HCI-mode\n");
+ }
+
+ msleep(PN544_BOOT_TIME);
+
+ return 0;
+}
+
+static void pn544_disable(struct pn544_info *info)
+{
+ struct pn544_nfc_platform_data *pdata;
+ struct i2c_client *client = info->i2c_dev;
+
+ pdata = client->dev.platform_data;
+ if (pdata->disable)
+ pdata->disable();
+
+ info->state = PN544_ST_COLD;
+
+ dev_dbg(&client->dev, "Now in OFF-mode\n");
+
+ msleep(PN544_RESETVEN_TIME);
+
+ info->read_irq = PN544_NONE;
+ regulator_bulk_disable(ARRAY_SIZE(info->regs), info->regs);
+}
+
+static int check_crc(u8 *buf, int buflen)
+{
+ u8 len;
+ u16 crc;
+
+ len = buf[0] + 1;
+ if (len < 4 || len != buflen || len > PN544_MSG_MAX_SIZE) {
+ pr_err(PN544_DRIVER_NAME
+ ": CRC; corrupt packet len %u (%d)\n", len, buflen);
+ print_hex_dump(KERN_DEBUG, "crc: ", DUMP_PREFIX_NONE,
+ 16, 2, buf, buflen, false);
+ return -EPERM;
+ }
+ crc = crc_ccitt(0xffff, buf, len - 2);
+ crc = ~crc;
+
+ if (buf[len-2] != (crc & 0xff) || buf[len-1] != (crc >> 8)) {
+ pr_err(PN544_DRIVER_NAME ": CRC error 0x%x != 0x%x 0x%x\n",
+ crc, buf[len-1], buf[len-2]);
+
+ print_hex_dump(KERN_DEBUG, "crc: ", DUMP_PREFIX_NONE,
+ 16, 2, buf, buflen, false);
+ return -EPERM;
+ }
+ return 0;
+}
+
+static int pn544_i2c_write(struct i2c_client *client, u8 *buf, int len)
+{
+ int r;
+
+ if (len < 4 || len != (buf[0] + 1)) {
+ dev_err(&client->dev, "%s: Illegal message length: %d\n",
+ __func__, len);
+ return -EINVAL;
+ }
+
+ if (check_crc(buf, len))
+ return -EINVAL;
+
+
+ msleep(PN544_I2C_IO_TIME);
+
+ r = i2c_master_send(client, buf, len);
+ dev_dbg(&client->dev, "send: %d\n", r);
+
+ if (r == -EREMOTEIO) { /* Retry, chip was in standby */
+ msleep(PN544_WAKEUP_GUARD);
+ r = i2c_master_send(client, buf, len);
+ dev_dbg(&client->dev, "send2: %d\n", r);
+ }
+
+ if (r != len)
+ return -EREMOTEIO;
+
+ return r;
+}
+
+static int pn544_i2c_read(struct i2c_client *client, u8 *buf, int buflen)
+{
+ int r;
+ u8 len;
+
+ /*
+ * You could read a packet in one go, but then you'd need to read
+ * max size and rest would be 0xff fill, so we do split reads.
+ */
+ r = i2c_master_recv(client, &len, 1);
+ dev_dbg(&client->dev, "recv1: %d\n", r);
+
+ if (r != 1)
+ return -EREMOTEIO;
+
+ if (len < PN544_LLC_HCI_OVERHEAD)
+ len = PN544_LLC_HCI_OVERHEAD;
+ else if (len > (PN544_MSG_MAX_SIZE - 1))
+ len = PN544_MSG_MAX_SIZE - 1;
+
+ if (1 + len > buflen) /* len+(data+crc16) */
+ return -EMSGSIZE;
+
+ buf[0] = len;
+
+ r = i2c_master_recv(client, buf + 1, len);
+ dev_dbg(&client->dev, "recv2: %d\n", r);
+
+ if (r != len)
+ return -EREMOTEIO;
+
+ msleep(PN544_I2C_IO_TIME);
+
+ return r + 1;
+}
+
+static int pn544_fw_write(struct i2c_client *client, u8 *buf, int len)
+{
+ int r;
+
+ dev_dbg(&client->dev, "%s\n", __func__);
+
+ if (len < PN544_FW_HEADER_SIZE ||
+ (PN544_FW_HEADER_SIZE + (buf[1] << 8) + buf[2]) != len)
+ return -EINVAL;
+
+ r = i2c_master_send(client, buf, len);
+ dev_dbg(&client->dev, "fw send: %d\n", r);
+
+ if (r == -EREMOTEIO) { /* Retry, chip was in standby */
+ msleep(PN544_WAKEUP_GUARD);
+ r = i2c_master_send(client, buf, len);
+ dev_dbg(&client->dev, "fw send2: %d\n", r);
+ }
+
+ if (r != len)
+ return -EREMOTEIO;
+
+ return r;
+}
+
+static int pn544_fw_read(struct i2c_client *client, u8 *buf, int buflen)
+{
+ int r, len;
+
+ if (buflen < PN544_FW_HEADER_SIZE)
+ return -EINVAL;
+
+ r = i2c_master_recv(client, buf, PN544_FW_HEADER_SIZE);
+ dev_dbg(&client->dev, "FW recv1: %d\n", r);
+
+ if (r < 0)
+ return r;
+
+ if (r < PN544_FW_HEADER_SIZE)
+ return -EINVAL;
+
+ len = (buf[1] << 8) + buf[2];
+ if (len == 0) /* just header, no additional data */
+ return r;
+
+ if (len > buflen - PN544_FW_HEADER_SIZE)
+ return -EMSGSIZE;
+
+ r = i2c_master_recv(client, buf + PN544_FW_HEADER_SIZE, len);
+ dev_dbg(&client->dev, "fw recv2: %d\n", r);
+
+ if (r != len)
+ return -EINVAL;
+
+ return r + PN544_FW_HEADER_SIZE;
+}
+
+static irqreturn_t pn544_irq_thread_fn(int irq, void *dev_id)
+{
+ struct pn544_info *info = dev_id;
+ struct i2c_client *client = info->i2c_dev;
+
+ BUG_ON(!info);
+ BUG_ON(irq != info->i2c_dev->irq);
+
+ dev_dbg(&client->dev, "IRQ\n");
+
+ mutex_lock(&info->read_mutex);
+ info->read_irq = PN544_INT;
+ mutex_unlock(&info->read_mutex);
+
+ wake_up_interruptible(&info->read_wait);
+
+ return IRQ_HANDLED;
+}
+
+static enum pn544_irq pn544_irq_state(struct pn544_info *info)
+{
+ enum pn544_irq irq;
+
+ mutex_lock(&info->read_mutex);
+ irq = info->read_irq;
+ mutex_unlock(&info->read_mutex);
+ /*
+ * XXX: should we check GPIO-line status directly?
+ * return pdata->irq_status() ? PN544_INT : PN544_NONE;
+ */
+
+ return irq;
+}
+
+static ssize_t pn544_read(struct file *file, char __user *buf,
+ size_t count, loff_t *offset)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+ enum pn544_irq irq;
+ size_t len;
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s: info: %p, count: %d\n", __func__,
+ info, count);
+
+ mutex_lock(&info->mutex);
+
+ if (info->state == PN544_ST_COLD) {
+ r = -ENODEV;
+ goto out;
+ }
+
+ irq = pn544_irq_state(info);
+ if (irq == PN544_NONE) {
+ if (file->f_flags & O_NONBLOCK) {
+ r = -EAGAIN;
+ goto out;
+ }
+
+ if (wait_event_interruptible(info->read_wait,
+ (info->read_irq == PN544_INT))) {
+ r = -ERESTARTSYS;
+ goto out;
+ }
+ }
+
+ if (info->state == PN544_ST_FW_READY) {
+ len = min(count, info->buflen);
+
+ mutex_lock(&info->read_mutex);
+ r = pn544_fw_read(info->i2c_dev, info->buf, len);
+ info->read_irq = PN544_NONE;
+ mutex_unlock(&info->read_mutex);
+
+ if (r < 0) {
+ dev_err(&info->i2c_dev->dev, "FW read failed: %d\n", r);
+ goto out;
+ }
+
+ print_hex_dump(KERN_DEBUG, "FW read: ", DUMP_PREFIX_NONE,
+ 16, 2, info->buf, r, false);
+
+ *offset += r;
+ if (copy_to_user(buf, info->buf, r)) {
+ r = -EFAULT;
+ goto out;
+ }
+ } else {
+ len = min(count, info->buflen);
+
+ mutex_lock(&info->read_mutex);
+ r = pn544_i2c_read(info->i2c_dev, info->buf, len);
+ info->read_irq = PN544_NONE;
+ mutex_unlock(&info->read_mutex);
+
+ if (r < 0) {
+ dev_err(&info->i2c_dev->dev, "read failed (%d)\n", r);
+ goto out;
+ }
+ print_hex_dump(KERN_DEBUG, "read: ", DUMP_PREFIX_NONE,
+ 16, 2, info->buf, r, false);
+
+ *offset += r;
+ if (copy_to_user(buf, info->buf, r)) {
+ r = -EFAULT;
+ goto out;
+ }
+ }
+
+out:
+ mutex_unlock(&info->mutex);
+
+ return r;
+}
+
+static unsigned int pn544_poll(struct file *file, poll_table *wait)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s: info: %p\n", __func__, info);
+
+ mutex_lock(&info->mutex);
+
+ if (info->state == PN544_ST_COLD) {
+ r = -ENODEV;
+ goto out;
+ }
+
+ poll_wait(file, &info->read_wait, wait);
+
+ if (pn544_irq_state(info) == PN544_INT) {
+ r = POLLIN | POLLRDNORM;
+ goto out;
+ }
+out:
+ mutex_unlock(&info->mutex);
+
+ return r;
+}
+
+static ssize_t pn544_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+ ssize_t len;
+ int r;
+
+ dev_dbg(&client->dev, "%s: info: %p, count %d\n", __func__,
+ info, count);
+
+ mutex_lock(&info->mutex);
+
+ if (info->state == PN544_ST_COLD) {
+ r = -ENODEV;
+ goto out;
+ }
+
+ /*
+ * XXX: should we detect rset-writes and clean possible
+ * read_irq state
+ */
+ if (info->state == PN544_ST_FW_READY) {
+ size_t fw_len;
+
+ if (count < PN544_FW_HEADER_SIZE) {
+ r = -EINVAL;
+ goto out;
+ }
+
+ len = min(count, info->buflen);
+ if (copy_from_user(info->buf, buf, len)) {
+ r = -EFAULT;
+ goto out;
+ }
+
+ print_hex_dump(KERN_DEBUG, "FW write: ", DUMP_PREFIX_NONE,
+ 16, 2, info->buf, len, false);
+
+ fw_len = PN544_FW_HEADER_SIZE + (info->buf[1] << 8) +
+ info->buf[2];
+
+ if (len > fw_len) /* 1 msg at a time */
+ len = fw_len;
+
+ r = pn544_fw_write(info->i2c_dev, info->buf, len);
+ } else {
+ if (count < PN544_LLC_MIN_SIZE) {
+ r = -EINVAL;
+ goto out;
+ }
+
+ len = min(count, info->buflen);
+ if (copy_from_user(info->buf, buf, len)) {
+ r = -EFAULT;
+ goto out;
+ }
+
+ print_hex_dump(KERN_DEBUG, "write: ", DUMP_PREFIX_NONE,
+ 16, 2, info->buf, len, false);
+
+ if (len > (info->buf[0] + 1)) /* 1 msg at a time */
+ len = info->buf[0] + 1;
+
+ r = pn544_i2c_write(info->i2c_dev, info->buf, len);
+ }
+out:
+ mutex_unlock(&info->mutex);
+
+ return r;
+
+}
+
+static long pn544_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+ struct pn544_nfc_platform_data *pdata;
+ unsigned int val;
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s: info: %p, cmd: 0x%x\n", __func__, info, cmd);
+
+ mutex_lock(&info->mutex);
+
+ if (info->state == PN544_ST_COLD) {
+ r = -ENODEV;
+ goto out;
+ }
+
+ pdata = info->i2c_dev->dev.platform_data;
+ switch (cmd) {
+ case PN544_GET_FW_MODE:
+ dev_dbg(&client->dev, "%s: PN544_GET_FW_MODE\n", __func__);
+
+ val = (info->state == PN544_ST_FW_READY);
+ if (copy_to_user((void __user *)arg, &val, sizeof(val))) {
+ r = -EFAULT;
+ goto out;
+ }
+
+ break;
+
+ case PN544_SET_FW_MODE:
+ dev_dbg(&client->dev, "%s: PN544_SET_FW_MODE\n", __func__);
+
+ if (copy_from_user(&val, (void __user *)arg, sizeof(val))) {
+ r = -EFAULT;
+ goto out;
+ }
+
+ if (val) {
+ if (info->state == PN544_ST_FW_READY)
+ break;
+
+ pn544_disable(info);
+ r = pn544_enable(info, FW_MODE);
+ if (r < 0)
+ goto out;
+ } else {
+ if (info->state == PN544_ST_READY)
+ break;
+ pn544_disable(info);
+ r = pn544_enable(info, HCI_MODE);
+ if (r < 0)
+ goto out;
+ }
+ file->f_pos = info->read_offset;
+ break;
+
+ case TCGETS:
+ dev_dbg(&client->dev, "%s: TCGETS\n", __func__);
+
+ r = -ENOIOCTLCMD;
+ break;
+
+ default:
+ dev_err(&client->dev, "Unknown ioctl 0x%x\n", cmd);
+ r = -ENOIOCTLCMD;
+ break;
+ }
+
+out:
+ mutex_unlock(&info->mutex);
+
+ return r;
+}
+
+static int pn544_open(struct inode *inode, struct file *file)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s: info: %p, client %p\n", __func__,
+ info, info->i2c_dev);
+
+ mutex_lock(&info->mutex);
+
+ /*
+ * Only 1 at a time.
+ * XXX: maybe user (counter) would work better
+ */
+ if (info->state != PN544_ST_COLD) {
+ r = -EBUSY;
+ goto out;
+ }
+
+ file->f_pos = info->read_offset;
+ r = pn544_enable(info, HCI_MODE);
+
+out:
+ mutex_unlock(&info->mutex);
+ return r;
+}
+
+static int pn544_close(struct inode *inode, struct file *file)
+{
+ struct pn544_info *info = container_of(file->private_data,
+ struct pn544_info, miscdev);
+ struct i2c_client *client = info->i2c_dev;
+
+ dev_dbg(&client->dev, "%s: info: %p, client %p\n",
+ __func__, info, info->i2c_dev);
+
+ mutex_lock(&info->mutex);
+ pn544_disable(info);
+ mutex_unlock(&info->mutex);
+
+ return 0;
+}
+
+static const struct file_operations pn544_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .read = pn544_read,
+ .write = pn544_write,
+ .poll = pn544_poll,
+ .open = pn544_open,
+ .release = pn544_close,
+ .unlocked_ioctl = pn544_ioctl,
+};
+
+#ifdef CONFIG_PM
+static int pn544_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct pn544_info *info;
+ int r = 0;
+
+ dev_info(&client->dev, "***\n%s: client %p\n***\n", __func__, client);
+
+ info = i2c_get_clientdata(client);
+ dev_info(&client->dev, "%s: info: %p, client %p\n", __func__,
+ info, client);
+
+ mutex_lock(&info->mutex);
+
+ switch (info->state) {
+ case PN544_ST_FW_READY:
+ /* Do not suspend while upgrading FW, please! */
+ r = -EPERM;
+ break;
+
+ case PN544_ST_READY:
+ /*
+ * CHECK: Device should be in standby-mode. No way to check?
+ * Allowing low power mode for the regulator is potentially
+ * dangerous if pn544 does not go to suspension.
+ */
+ break;
+
+ case PN544_ST_COLD:
+ break;
+ };
+
+ mutex_unlock(&info->mutex);
+ return r;
+}
+
+static int pn544_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct pn544_info *info = i2c_get_clientdata(client);
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s: info: %p, client %p\n", __func__,
+ info, client);
+
+ mutex_lock(&info->mutex);
+
+ switch (info->state) {
+ case PN544_ST_READY:
+ /*
+ * CHECK: If regulator low power mode is allowed in
+ * pn544_suspend, we should go back to normal mode
+ * here.
+ */
+ break;
+
+ case PN544_ST_COLD:
+ break;
+
+ case PN544_ST_FW_READY:
+ break;
+ };
+
+ mutex_unlock(&info->mutex);
+
+ return r;
+}
+
+static SIMPLE_DEV_PM_OPS(pn544_pm_ops, pn544_suspend, pn544_resume);
+#endif
+
+static struct device_attribute pn544_attr =
+ __ATTR(nfc_test, S_IRUGO, pn544_test, NULL);
+
+static int __devinit pn544_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct pn544_info *info;
+ struct pn544_nfc_platform_data *pdata;
+ int r = 0;
+
+ dev_dbg(&client->dev, "%s\n", __func__);
+ dev_dbg(&client->dev, "IRQ: %d\n", client->irq);
+
+ /* private data allocation */
+ info = kzalloc(sizeof(struct pn544_info), GFP_KERNEL);
+ if (!info) {
+ dev_err(&client->dev,
+ "Cannot allocate memory for pn544_info.\n");
+ r = -ENOMEM;
+ goto err_info_alloc;
+ }
+
+ info->buflen = max(PN544_MSG_MAX_SIZE, PN544_MAX_I2C_TRANSFER);
+ info->buf = kzalloc(info->buflen, GFP_KERNEL);
+ if (!info->buf) {
+ dev_err(&client->dev,
+ "Cannot allocate memory for pn544_info->buf.\n");
+ r = -ENOMEM;
+ goto err_buf_alloc;
+ }
+
+ info->regs[0].supply = reg_vdd_io;
+ info->regs[1].supply = reg_vbat;
+ r = regulator_bulk_get(&client->dev, ARRAY_SIZE(info->regs),
+ info->regs);
+ if (r < 0)
+ goto err_kmalloc;
+
+ info->i2c_dev = client;
+ info->state = PN544_ST_COLD;
+ info->read_irq = PN544_NONE;
+ mutex_init(&info->read_mutex);
+ mutex_init(&info->mutex);
+ init_waitqueue_head(&info->read_wait);
+ i2c_set_clientdata(client, info);
+ pdata = client->dev.platform_data;
+ if (!pdata) {
+ dev_err(&client->dev, "No platform data\n");
+ r = -EINVAL;
+ goto err_reg;
+ }
+
+ if (!pdata->request_resources) {
+ dev_err(&client->dev, "request_resources() missing\n");
+ r = -EINVAL;
+ goto err_reg;
+ }
+
+ r = pdata->request_resources(client);
+ if (r) {
+ dev_err(&client->dev, "Cannot get platform resources\n");
+ goto err_reg;
+ }
+
+ r = request_threaded_irq(client->irq, NULL, pn544_irq_thread_fn,
+ IRQF_TRIGGER_RISING, PN544_DRIVER_NAME,
+ info);
+ if (r < 0) {
+ dev_err(&client->dev, "Unable to register IRQ handler\n");
+ goto err_res;
+ }
+
+ /* If we don't have the test we don't need the sysfs file */
+ if (pdata->test) {
+ r = device_create_file(&client->dev, &pn544_attr);
+ if (r) {
+ dev_err(&client->dev,
+ "sysfs registration failed, error %d\n", r);
+ goto err_irq;
+ }
+ }
+
+ info->miscdev.minor = MISC_DYNAMIC_MINOR;
+ info->miscdev.name = PN544_DRIVER_NAME;
+ info->miscdev.fops = &pn544_fops;
+ info->miscdev.parent = &client->dev;
+ r = misc_register(&info->miscdev);
+ if (r < 0) {
+ dev_err(&client->dev, "Device registration failed\n");
+ goto err_sysfs;
+ }
+
+ dev_dbg(&client->dev, "%s: info: %p, pdata %p, client %p\n",
+ __func__, info, pdata, client);
+
+ return 0;
+
+err_sysfs:
+ if (pdata->test)
+ device_remove_file(&client->dev, &pn544_attr);
+err_irq:
+ free_irq(client->irq, info);
+err_res:
+ if (pdata->free_resources)
+ pdata->free_resources();
+err_reg:
+ regulator_bulk_free(ARRAY_SIZE(info->regs), info->regs);
+err_kmalloc:
+ kfree(info->buf);
+err_buf_alloc:
+ kfree(info);
+err_info_alloc:
+ return r;
+}
+
+static __devexit int pn544_remove(struct i2c_client *client)
+{
+ struct pn544_info *info = i2c_get_clientdata(client);
+ struct pn544_nfc_platform_data *pdata = client->dev.platform_data;
+
+ dev_dbg(&client->dev, "%s\n", __func__);
+
+ misc_deregister(&info->miscdev);
+ if (pdata->test)
+ device_remove_file(&client->dev, &pn544_attr);
+
+ if (info->state != PN544_ST_COLD) {
+ if (pdata->disable)
+ pdata->disable();
+
+ info->read_irq = PN544_NONE;
+ }
+
+ free_irq(client->irq, info);
+ if (pdata->free_resources)
+ pdata->free_resources();
+
+ regulator_bulk_free(ARRAY_SIZE(info->regs), info->regs);
+ kfree(info->buf);
+ kfree(info);
+
+ return 0;
+}
+
+static struct i2c_driver pn544_driver = {
+ .driver = {
+ .name = PN544_DRIVER_NAME,
+#ifdef CONFIG_PM
+ .pm = &pn544_pm_ops,
+#endif
+ },
+ .probe = pn544_probe,
+ .id_table = pn544_id_table,
+ .remove = __devexit_p(pn544_remove),
+};
+
+static int __init pn544_init(void)
+{
+ int r;
+
+ pr_debug(DRIVER_DESC ": %s\n", __func__);
+
+ r = i2c_add_driver(&pn544_driver);
+ if (r) {
+ pr_err(PN544_DRIVER_NAME ": driver registration failed\n");
+ return r;
+ }
+
+ return 0;
+}
+
+static void __exit pn544_exit(void)
+{
+ flush_scheduled_work();
+ i2c_del_driver(&pn544_driver);
+ pr_info(DRIVER_DESC ", Exiting.\n");
+}
+
+module_init(pn544_init);
+module_exit(pn544_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION(DRIVER_DESC);
diff -puN /dev/null include/linux/nfc/pn544.h
--- /dev/null
+++ a/include/linux/nfc/pn544.h
@@ -0,0 +1,99 @@
+/*
+ * Driver include for the PN544 NFC chip.
+ *
+ * Copyright (C) Nokia Corporation
+ *
+ * Author: Jari Vanhala <ext-jari.vanhala@nokia.com>
+ * Contact: Matti Aaltoenn <matti.j.aaltonen@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _PN544_H_
+#define _PN544_H_
+
+#include <linux/i2c.h>
+
+#define PN544_DRIVER_NAME "pn544"
+#define PN544_MAXWINDOW_SIZE 7
+#define PN544_WINDOW_SIZE 4
+#define PN544_RETRIES 10
+#define PN544_MAX_I2C_TRANSFER 0x0400
+#define PN544_MSG_MAX_SIZE 0x21 /* at normal HCI mode */
+
+/* ioctl */
+#define PN544_CHAR_BASE 'P'
+#define PN544_IOR(num, dtype) _IOR(PN544_CHAR_BASE, num, dtype)
+#define PN544_IOW(num, dtype) _IOW(PN544_CHAR_BASE, num, dtype)
+#define PN544_GET_FW_MODE PN544_IOW(1, unsigned int)
+#define PN544_SET_FW_MODE PN544_IOW(2, unsigned int)
+#define PN544_GET_DEBUG PN544_IOW(3, unsigned int)
+#define PN544_SET_DEBUG PN544_IOW(4, unsigned int)
+
+/* Timing restrictions (ms) */
+#define PN544_RESETVEN_TIME 30 /* 7 */
+#define PN544_PVDDVEN_TIME 0
+#define PN544_VBATVEN_TIME 0
+#define PN544_GPIO4VEN_TIME 0
+#define PN544_BOOT_TIME 10 /* 3 */
+#define PN544_I2C_IO_TIME 3 /* 100 */
+#define PN544_WAKEUP_ACK 5
+#define PN544_WAKEUP_GUARD (PN544_WAKEUP_ACK + 1)
+#define PN544_INACTIVITY_TIME 1000
+#define PN544_INTERFRAME_DELAY 200 /* us */
+#define PN544_BAUDRATE_CHANGE 150 /* us */
+
+/* Debug bits */
+#define PN544_DEBUG_BUF 0x01
+#define PN544_DEBUG_READ 0x02
+#define PN544_DEBUG_WRITE 0x04
+#define PN544_DEBUG_IRQ 0x08
+#define PN544_DEBUG_CALLS 0x10
+#define PN544_DEBUG_MODE 0x20
+
+/* Normal (HCI) mode */
+#define PN544_LLC_HCI_OVERHEAD 3 /* header + crc (to length) */
+#define PN544_LLC_MIN_SIZE (1 + PN544_LLC_HCI_OVERHEAD) /* length + */
+#define PN544_LLC_MAX_DATA (PN544_MSG_MAX_SIZE - 2)
+#define PN544_LLC_MAX_HCI_SIZE (PN544_LLC_MAX_DATA - 2)
+
+struct pn544_llc_packet {
+ unsigned char length; /* of rest of packet */
+ unsigned char header;
+ unsigned char data[PN544_LLC_MAX_DATA]; /* includes crc-ccitt */
+};
+
+/* Firmware upgrade mode */
+#define PN544_FW_HEADER_SIZE 3
+/* max fw transfer is 1024bytes, but I2C limits it to 0xC0 */
+#define PN544_MAX_FW_DATA (PN544_MAX_I2C_TRANSFER - PN544_FW_HEADER_SIZE)
+
+struct pn544_fw_packet {
+ unsigned char command; /* status in answer */
+ unsigned char length[2]; /* big-endian order (msf) */
+ unsigned char data[PN544_MAX_FW_DATA];
+};
+
+#ifdef __KERNEL__
+/* board config */
+struct pn544_nfc_platform_data {
+ int (*request_resources) (struct i2c_client *client);
+ void (*free_resources) (void);
+ void (*enable) (int fw);
+ int (*test) (void);
+ void (*disable) (void);
+};
+#endif /* __KERNEL__ */
+
+#endif /* _PN544_H_ */
_
Patches currently in -mm which might be from matti.j.aaltonen@nokia.com are
origin.patch
nfc-driver-for-nxp-semiconductors-pn544-nfc-chip.patch
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2010-10-29 21:35 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-10-29 21:35 + nfc-driver-for-nxp-semiconductors-pn544-nfc-chip.patch added to -mm tree akpm
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.