[PATCH net-next-2.6 v3 0/2] can: add driver for Softing card

[PATCH net-next-2.6 v3 0/2] can: add driver for Softing card

[Kurt Van Dijck]

This series will add a driver for Softing PCMCIA CAN card.

This core CAN networking code exists for a few years in the
socketCAN repository.
The updates since the latest socketCAN version:
* PCMCIA interfacing changed
* seperation between the two drivers via a platform:softing device
* added conditional bus-error reporting

About the platform_device ...
Softing Gmbh has PCMCIA & PCI cards. Both share the same
Dual Port RAM (DPRAM) interface. Therefore, the driver is split in 2 stages:

[1/2] softing.ko: Generic platform bus device driver
It expects a platform:softing device with an IO range that contains
the DPRAM, and an IRQ line.

[2/2] softing_cs.ko: PCMCIA driver
This driver will create a platform:softing device on top of the
pcmcia device.

The 2 drivers are not linked in a way that softing.ko depends
on softing_cs.ko or vice versa. The reason for doing so is that
the DPRAM interface takes quite some code, and building it directly
on the PCMCIA or PCI device was difficult to follow.
The present design eliminates the need for exotic sysfs API's since
all sysfs attributes know they are attached to a platform_device.

Differences since v1 of this series:
* whitespace issues
* use of time_after() to measure elapsed time.
* don't copy data for RTR frames (see commit since v1)
* use usleep_range(), not schedule().
* threaded irq
* fix iomem access (verify with sparse)
* totally 'endian-safe'
* drop error frame detection again. It's not right that when
  bus 1 enables error frames, bus 2 would get error frames too.
* drop the Kconfig dependency between softingcs.ko & softing.ko

Differences since v2 of this series:
* Even more whitespace issues
* Let softing_cs.ko depend on softing.ko in Kconfig. A real
  user will need them both
* Normalize all frequencies in Hz.
* Proper return codes from firmware communication functions.
* Drop some alignments
* Don't touch byte counters on RTR frames
* Fix bus-error-states
* Less obscure use of bitmasks
* use of __devinit/__devexit
...

Kurt

[PATCH net-next-2.6 v3 1/2] can: add driver for Softing card

[Kurt Van Dijck]

This patch adds a driver for the platform:softing device.
This will create (up to) 2 CAN network devices from 1
platform:softing device

Signed-off-by: Kurt Van Dijck <kurt.van.dijck-/BeEPy95v10@public.gmane.org>
Acked-by: Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>
---
 drivers/net/can/Kconfig                    |    2 +
 drivers/net/can/Makefile                   |    1 +
 drivers/net/can/softing/Kconfig            |   16 +
 drivers/net/can/softing/Makefile           |    5 +
 drivers/net/can/softing/softing.h          |  168 ++++++
 drivers/net/can/softing/softing_fw.c       |  692 +++++++++++++++++++++
 drivers/net/can/softing/softing_main.c     |  893 ++++++++++++++++++++++++++++
 drivers/net/can/softing/softing_platform.h |   41 ++
 8 files changed, 1818 insertions(+), 0 deletions(-)

diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index d5a9db6..986195e 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -117,6 +117,8 @@ source "drivers/net/can/sja1000/Kconfig"
 
 source "drivers/net/can/usb/Kconfig"
 
+source "drivers/net/can/softing/Kconfig"
+
 config CAN_DEBUG_DEVICES
 	bool "CAN devices debugging messages"
 	depends on CAN
diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile
index 07ca159..53c82a7 100644
--- a/drivers/net/can/Makefile
+++ b/drivers/net/can/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_CAN_DEV)		+= can-dev.o
 can-dev-y			:= dev.o
 
 obj-y				+= usb/
+obj-y				+= softing/
 
 obj-$(CONFIG_CAN_SJA1000)	+= sja1000/
 obj-$(CONFIG_CAN_MSCAN)		+= mscan/
diff --git a/drivers/net/can/softing/Kconfig b/drivers/net/can/softing/Kconfig
new file mode 100644
index 0000000..072f337
--- /dev/null
+++ b/drivers/net/can/softing/Kconfig
@@ -0,0 +1,16 @@
+config CAN_SOFTING
+	tristate "Softing Gmbh CAN generic support"
+	depends on CAN_DEV
+	---help---
+	  Support for CAN cards from Softing Gmbh & some cards
+	  from Vector Gmbh.
+	  Softing Gmbh CAN cards come with 1 or 2 physical busses.
+	  Those cards typically use Dual Port RAM to communicate
+	  with the host CPU. The interface is then identical for PCI
+	  and PCMCIA cards. This driver operates on a platform device,
+	  which has been created by softing_cs or softing_pci driver.
+	  Warning:
+	  The API of the card does not allow fine control per bus, but
+	  controls the 2 busses on the card together.
+	  As such, some actions (start/stop/busoff recovery) on 1 bus
+	  must bring down the other bus too temporarily.
diff --git a/drivers/net/can/softing/Makefile b/drivers/net/can/softing/Makefile
new file mode 100644
index 0000000..7db0445
--- /dev/null
+++ b/drivers/net/can/softing/Makefile
@@ -0,0 +1,5 @@
+
+softing-y := softing_main.o softing_fw.o
+obj-$(CONFIG_CAN_SOFTING) += softing.o
+
+ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
diff --git a/drivers/net/can/softing/softing.h b/drivers/net/can/softing/softing.h
new file mode 100644
index 0000000..7479ee1
--- /dev/null
+++ b/drivers/net/can/softing/softing.h
@@ -0,0 +1,168 @@
+/*
+ * softing common interfaces
+ *
+ * by Kurt Van Dijck, 2008-2010
+ */
+
+#include <linux/atomic.h>
+#include <linux/netdevice.h>
+#include <linux/ktime.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/can.h>
+#include <linux/can/dev.h>
+
+#include "softing_platform.h"
+
+struct softing;
+
+struct softing_priv {
+	struct can_priv can; /* must be the first member! */
+	struct net_device *netdev;
+	struct softing *card;
+	struct {
+		int pending;
+		/* variables wich hold the circular buffer */
+		int echo_put;
+		int echo_get;
+	} tx;
+	struct can_bittiming_const btr_const;
+	int index;
+	uint8_t output;
+	uint16_t chip;
+};
+#define netdev2softing(netdev)	((struct softing_priv *)netdev_priv(netdev))
+
+struct softing {
+	const struct softing_platform_data *pdat;
+	struct platform_device *pdev;
+	struct net_device *net[2];
+	spinlock_t spin; /* protect this structure & DPRAM access */
+	ktime_t ts_ref;
+	ktime_t ts_overflow; /* timestamp overflow value, in ktime */
+
+	struct {
+		/* indication of firmware status */
+		int up;
+		/* protection of the 'up' variable */
+		struct mutex lock;
+	} fw;
+	struct {
+		int nr;
+		int requested;
+		int svc_count;
+		unsigned int dpram_position;
+	} irq;
+	struct {
+		int pending;
+		int last_bus;
+		/*
+		 * keep the bus that last tx'd a message,
+		 * in order to let every netdev queue resume
+		 */
+	} tx;
+	__iomem uint8_t *dpram;
+	unsigned long dpram_phys;
+	unsigned long dpram_size;
+	struct {
+		uint16_t fw_version, hw_version, license, serial;
+		uint16_t chip[2];
+		unsigned int freq; /* remote cpu's operating frequency */
+	} id;
+};
+
+extern int softing_default_output(struct net_device *netdev);
+
+extern ktime_t softing_raw2ktime(struct softing *card, u32 raw);
+
+extern int softing_chip_poweron(struct softing *card);
+
+extern int softing_bootloader_command(struct softing *card, int16_t cmd,
+		const char *msg);
+
+/* Load firmware after reset */
+extern int softing_load_fw(const char *file, struct softing *card,
+			__iomem uint8_t *virt, unsigned int size, int offset);
+
+/* Load final application firmware after bootloader */
+extern int softing_load_app_fw(const char *file, struct softing *card);
+
+/*
+ * enable or disable irq
+ * only called with fw.lock locked
+ */
+extern int softing_enable_irq(struct softing *card, int enable);
+
+/* start/stop 1 bus on card */
+extern int softing_startstop(struct net_device *netdev, int up);
+
+/* netif_rx() */
+extern int softing_netdev_rx(struct net_device *netdev,
+		const struct can_frame *msg, ktime_t ktime);
+
+/* SOFTING DPRAM mappings */
+#define DPRAM_RX		0x0000
+	#define DPRAM_RX_SIZE	32
+	#define DPRAM_RX_CNT	16
+#define DPRAM_RX_RD		0x0201	/* uint8_t */
+#define DPRAM_RX_WR		0x0205	/* uint8_t */
+#define DPRAM_RX_LOST		0x0207	/* uint8_t */
+
+#define DPRAM_FCT_PARAM		0x0300	/* int16_t [20] */
+#define DPRAM_FCT_RESULT	0x0328	/* int16_t */
+#define DPRAM_FCT_HOST		0x032b	/* uint16_t */
+
+#define DPRAM_INFO_BUSSTATE	0x0331	/* uint16_t */
+#define DPRAM_INFO_BUSSTATE2	0x0335	/* uint16_t */
+#define DPRAM_INFO_ERRSTATE	0x0339	/* uint16_t */
+#define DPRAM_INFO_ERRSTATE2	0x033d	/* uint16_t */
+#define DPRAM_RESET		0x0341	/* uint16_t */
+#define DPRAM_CLR_RECV_FIFO	0x0345	/* uint16_t */
+#define DPRAM_RESET_TIME	0x034d	/* uint16_t */
+#define DPRAM_TIME		0x0350	/* uint64_t */
+#define DPRAM_WR_START		0x0358	/* uint8_t */
+#define DPRAM_WR_END		0x0359	/* uint8_t */
+#define DPRAM_RESET_RX_FIFO	0x0361	/* uint16_t */
+#define DPRAM_RESET_TX_FIFO	0x0364	/* uint8_t */
+#define DPRAM_READ_FIFO_LEVEL	0x0365	/* uint8_t */
+#define DPRAM_RX_FIFO_LEVEL	0x0366	/* uint16_t */
+#define DPRAM_TX_FIFO_LEVEL	0x0366	/* uint16_t */
+
+#define DPRAM_TX		0x0400	/* uint16_t */
+	#define DPRAM_TX_SIZE	16
+	#define DPRAM_TX_CNT	32
+#define DPRAM_TX_RD		0x0601	/* uint8_t */
+#define DPRAM_TX_WR		0x0605	/* uint8_t */
+
+#define DPRAM_COMMAND		0x07e0	/* uint16_t */
+#define DPRAM_RECEIPT		0x07f0	/* uint16_t */
+#define DPRAM_IRQ_TOHOST	0x07fe	/* uint8_t */
+#define DPRAM_IRQ_TOCARD	0x07ff	/* uint8_t */
+
+#define DPRAM_V2_RESET		0x0e00	/* uint8_t */
+#define DPRAM_V2_IRQ_TOHOST	0x0e02	/* uint8_t */
+
+#define TXMAX	(DPRAM_TX_CNT - 1)
+
+/* DPRAM return codes */
+#define RES_NONE	0
+#define RES_OK		1
+#define RES_NOK		2
+#define RES_UNKNOWN	3
+/* DPRAM flags */
+#define CMD_TX		0x01
+#define CMD_ACK		0x02
+#define CMD_XTD		0x04
+#define CMD_RTR		0x08
+#define CMD_ERR		0x10
+#define CMD_BUS2	0x80
+
+/* returned fifo entry bus state masks */
+#define SF_MASK_BUSOFF		0x80
+#define SF_MASK_EPASSIVE	0x60
+
+/* bus states */
+#define STATE_BUSOFF	2
+#define STATE_EPASSIVE	1
+#define STATE_EACTIVE	0
+
diff --git a/drivers/net/can/softing/softing_fw.c b/drivers/net/can/softing/softing_fw.c
new file mode 100644
index 0000000..ec42a87
--- /dev/null
+++ b/drivers/net/can/softing/softing_fw.c
@@ -0,0 +1,692 @@
+/*
+ * Copyright (C) 2008-2010
+ *
+ * - Kurt Van Dijck, EIA Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/firmware.h>
+#include <linux/sched.h>
+#include <asm/div64.h>
+
+#include "softing.h"
+
+/*
+ * low level DPRAM command.
+ * Make sure that card->dpram[DPRAM_FCT_HOST] is preset
+ */
+static int _softing_fct_cmd(struct softing *card, int16_t cmd, uint16_t vector,
+		const char *msg)
+{
+	int ret;
+	unsigned long stamp;
+
+	iowrite16(cmd, &card->dpram[DPRAM_FCT_PARAM]);
+	iowrite8(vector >> 8, &card->dpram[DPRAM_FCT_HOST + 1]);
+	iowrite8(vector, &card->dpram[DPRAM_FCT_HOST]);
+	/* be sure to flush this to the card */
+	wmb();
+	stamp = jiffies + 1 * HZ;
+	/* wait for card */
+	do {
+		/* DPRAM_FCT_HOST is _not_ aligned */
+		ret = ioread8(&card->dpram[DPRAM_FCT_HOST]) +
+			(ioread8(&card->dpram[DPRAM_FCT_HOST + 1]) << 8);
+		/* don't have any cached variables */
+		rmb();
+		if (ret == RES_OK)
+			/* read return-value now */
+			return ioread16(&card->dpram[DPRAM_FCT_RESULT]);
+
+		if ((ret != vector) || time_after(jiffies, stamp))
+			break;
+		/* process context => relax */
+		usleep_range(500, 10000);
+	} while (1);
+
+	ret = (ret == RES_NONE) ? -ETIMEDOUT : -ECANCELED;
+	dev_alert(&card->pdev->dev, "firmware %s failed (%i)\n", msg, ret);
+	return ret;
+}
+
+static int softing_fct_cmd(struct softing *card, int16_t cmd, const char *msg)
+{
+	int ret;
+
+	ret = _softing_fct_cmd(card, cmd, 0, msg);
+	if (ret > 0) {
+		dev_alert(&card->pdev->dev, "%s returned %u\n", msg, ret);
+		ret = -EIO;
+	}
+	return ret;
+}
+
+int softing_bootloader_command(struct softing *card, int16_t cmd,
+		const char *msg)
+{
+	int ret;
+	unsigned long stamp;
+
+	iowrite16(RES_NONE, &card->dpram[DPRAM_RECEIPT]);
+	iowrite16(cmd, &card->dpram[DPRAM_COMMAND]);
+	/* be sure to flush this to the card */
+	wmb();
+	stamp = jiffies + 3 * HZ;
+	/* wait for card */
+	do {
+		ret = ioread16(&card->dpram[DPRAM_RECEIPT]);
+		/* don't have any cached variables */
+		rmb();
+		if (ret == RES_OK)
+			return 0;
+		if (time_after(jiffies, stamp))
+			break;
+		/* process context => relax */
+		usleep_range(500, 10000);
+	} while (!signal_pending(current));
+
+	ret = (ret == RES_NONE) ? -ETIMEDOUT : -ECANCELED;
+	dev_alert(&card->pdev->dev, "bootloader %s failed (%i)\n", msg, ret);
+	return ret;
+}
+
+static int fw_parse(const uint8_t **pmem, uint16_t *ptype, uint32_t *paddr,
+		uint16_t *plen, const uint8_t **pdat)
+{
+	uint16_t checksum[2];
+	const uint8_t *mem;
+	const uint8_t *end;
+
+	/*
+	 * firmware records are a binary, unaligned stream composed of:
+	 * uint16_t type;
+	 * uint32_t addr;
+	 * uint16_t len;
+	 * uint8_t dat[len];
+	 * uint16_t checksum;
+	 * all values in little endian.
+	 * We could define a struct for this, with __attribute__((packed)),
+	 * but would that solve the alignment in _all_ cases (cfr. the
+	 * struct itself may be an odd address)?
+	 *
+	 * I chose to use leXX_to_cpup() since this solves both
+	 * endianness & alignment.
+	 */
+	mem = *pmem;
+	*ptype = le16_to_cpup((void *)&mem[0]);
+	*paddr = le32_to_cpup((void *)&mem[2]);
+	*plen = le16_to_cpup((void *)&mem[6]);
+	*pdat = &mem[8];
+	/* verify checksum */
+	end = &mem[8 + *plen];
+	checksum[0] = le16_to_cpup((void *)end);
+	for (checksum[1] = 0; mem < end; ++mem)
+		checksum[1] += *mem;
+	if (checksum[0] != checksum[1])
+		return -EINVAL;
+	/* increment */
+	*pmem += 10 + *plen;
+	return 0;
+}
+
+int softing_load_fw(const char *file, struct softing *card,
+		__iomem uint8_t *dpram, unsigned int size, int offset)
+{
+	const struct firmware *fw;
+	int ret;
+	const uint8_t *mem, *end, *dat;
+	uint16_t type, len;
+	uint32_t addr;
+	uint8_t *buf = NULL;
+	int buflen = 0;
+	int8_t type_end = 0;
+
+	ret = request_firmware(&fw, file, &card->pdev->dev);
+	if (ret < 0)
+		return ret;
+	dev_dbg(&card->pdev->dev, "%s, firmware(%s) got %u bytes"
+		", offset %c0x%04x\n",
+		card->pdat->name, file, (unsigned int)fw->size,
+		(offset >= 0) ? '+' : '-', (unsigned int)abs(offset));
+	/* parse the firmware */
+	mem = fw->data;
+	end = &mem[fw->size];
+	/* look for header record */
+	ret = fw_parse(&mem, &type, &addr, &len, &dat);
+	if (ret < 0)
+		goto failed;
+	if (type != 0xffff)
+		goto failed;
+	if (strncmp("Structured Binary Format, Softing GmbH" , dat, len)) {
+		ret = -EINVAL;
+		goto failed;
+	}
+	/* ok, we had a header */
+	while (mem < end) {
+		ret = fw_parse(&mem, &type, &addr, &len, &dat);
+		if (ret < 0)
+			goto failed;
+		if (type == 3) {
+			/* start address, not used here */
+			continue;
+		} else if (type == 1) {
+			/* eof */
+			type_end = 1;
+			break;
+		} else if (type != 0) {
+			ret = -EINVAL;
+			goto failed;
+		}
+
+		if ((addr + len + offset) > size)
+			goto failed;
+		memcpy_toio(&dpram[addr + offset], dat, len);
+		/* be sure to flush caches from IO space */
+		mb();
+		if (len > buflen) {
+			/* align buflen */
+			buflen = (len + (1024-1)) & ~(1024-1);
+			buf = krealloc(buf, buflen, GFP_KERNEL);
+			if (!buf) {
+				ret = -ENOMEM;
+				goto failed;
+			}
+		}
+		/* verify record data */
+		memcpy_fromio(buf, &dpram[addr + offset], len);
+		if (memcmp(buf, dat, len)) {
+			/* is not ok */
+			dev_alert(&card->pdev->dev, "DPRAM readback failed\n");
+			ret = -EIO;
+			goto failed;
+		}
+	}
+	if (!type_end)
+		/* no end record seen */
+		goto failed;
+	ret = 0;
+failed:
+	kfree(buf);
+	release_firmware(fw);
+	if (ret < 0)
+		dev_info(&card->pdev->dev, "firmware %s failed\n", file);
+	return ret;
+}
+
+int softing_load_app_fw(const char *file, struct softing *card)
+{
+	const struct firmware *fw;
+	const uint8_t *mem, *end, *dat;
+	int ret, j;
+	uint16_t type, len;
+	uint32_t addr, start_addr = 0;
+	unsigned int sum, rx_sum;
+	int8_t type_end = 0, type_entrypoint = 0;
+
+	ret = request_firmware(&fw, file, &card->pdev->dev);
+	if (ret) {
+		dev_alert(&card->pdev->dev, "request_firmware(%s) got %i\n",
+			file, ret);
+		return ret;
+	}
+	dev_dbg(&card->pdev->dev, "firmware(%s) got %lu bytes\n",
+		file, (unsigned long)fw->size);
+	/* parse the firmware */
+	mem = fw->data;
+	end = &mem[fw->size];
+	/* look for header record */
+	ret = fw_parse(&mem, &type, &addr, &len, &dat);
+	if (ret)
+		goto failed;
+	ret = -EINVAL;
+	if (type != 0xffff) {
+		dev_alert(&card->pdev->dev, "firmware starts with type 0x%x\n",
+			type);
+		goto failed;
+	}
+	if (strncmp("Structured Binary Format, Softing GmbH", dat, len)) {
+		dev_alert(&card->pdev->dev, "firmware string '%.*s' fault\n",
+				len, dat);
+		goto failed;
+	}
+	/* ok, we had a header */
+	while (mem < end) {
+		ret = fw_parse(&mem, &type, &addr, &len, &dat);
+		if (ret)
+			goto failed;
+
+		if (type == 3) {
+			/* start address */
+			start_addr = addr;
+			type_entrypoint = 1;
+			continue;
+		} else if (type == 1) {
+			/* eof */
+			type_end = 1;
+			break;
+		} else if (type != 0) {
+			dev_alert(&card->pdev->dev,
+					"unknown record type 0x%04x\n", type);
+			ret = -EINVAL;
+			goto failed;
+		}
+
+		/* regualar data */
+		for (sum = 0, j = 0; j < len; ++j)
+			sum += dat[j];
+		/* work in 16bit (target) */
+		sum &= 0xffff;
+
+		memcpy_toio(&card->dpram[card->pdat->app.offs], dat, len);
+		iowrite32(card->pdat->app.offs + card->pdat->app.addr,
+				&card->dpram[DPRAM_COMMAND + 2]);
+		iowrite32(addr, &card->dpram[DPRAM_COMMAND + 6]);
+		iowrite16(len, &card->dpram[DPRAM_COMMAND + 10]);
+		iowrite8(1, &card->dpram[DPRAM_COMMAND + 12]);
+		ret = softing_bootloader_command(card, 1, "loading app.");
+		if (ret < 0)
+			goto failed;
+		/* verify checksum */
+		rx_sum = ioread16(&card->dpram[DPRAM_RECEIPT + 2]);
+		if (rx_sum != sum) {
+			dev_alert(&card->pdev->dev, "SRAM seems to be damaged"
+				", wanted 0x%04x, got 0x%04x\n", sum, rx_sum);
+			ret = -EIO;
+			goto failed;
+		}
+	}
+	if (!type_end || !type_entrypoint)
+		goto failed;
+	/* start application in card */
+	iowrite32(start_addr, &card->dpram[DPRAM_COMMAND + 2]);
+	iowrite8(1, &card->dpram[DPRAM_COMMAND + 6]);
+	ret = softing_bootloader_command(card, 3, "start app.");
+	if (ret < 0)
+		goto failed;
+	ret = 0;
+failed:
+	release_firmware(fw);
+	if (ret < 0)
+		dev_info(&card->pdev->dev, "firmware %s failed\n", file);
+	return ret;
+}
+
+static int softing_reset_chip(struct softing *card)
+{
+	int ret;
+
+	do {
+		/* reset chip */
+		iowrite8(0, &card->dpram[DPRAM_RESET_RX_FIFO]);
+		iowrite8(0, &card->dpram[DPRAM_RESET_RX_FIFO+1]);
+		iowrite8(1, &card->dpram[DPRAM_RESET]);
+		iowrite8(0, &card->dpram[DPRAM_RESET+1]);
+
+		ret = softing_fct_cmd(card, 0, "reset_can");
+		if (!ret)
+			break;
+		if (signal_pending(current))
+			/* don't wait any longer */
+			break;
+	} while (1);
+	card->tx.pending = 0;
+	return ret;
+}
+
+int softing_chip_poweron(struct softing *card)
+{
+	int ret;
+	/* sync */
+	ret = _softing_fct_cmd(card, 99, 0x55, "sync-a");
+	if (ret < 0)
+		goto failed;
+
+	ret = _softing_fct_cmd(card, 99, 0xaa, "sync-b");
+	if (ret < 0)
+		goto failed;
+
+	ret = softing_reset_chip(card);
+	if (ret < 0)
+		goto failed;
+	/* get_serial */
+	ret = softing_fct_cmd(card, 43, "get_serial_number");
+	if (ret < 0)
+		goto failed;
+	card->id.serial = ioread32(&card->dpram[DPRAM_FCT_PARAM]);
+	/* get_version */
+	ret = softing_fct_cmd(card, 12, "get_version");
+	if (ret < 0)
+		goto failed;
+	card->id.fw_version = ioread16(&card->dpram[DPRAM_FCT_PARAM + 2]);
+	card->id.hw_version = ioread16(&card->dpram[DPRAM_FCT_PARAM + 4]);
+	card->id.license = ioread16(&card->dpram[DPRAM_FCT_PARAM + 6]);
+	card->id.chip[0] = ioread16(&card->dpram[DPRAM_FCT_PARAM + 8]);
+	card->id.chip[1] = ioread16(&card->dpram[DPRAM_FCT_PARAM + 10]);
+	return 0;
+failed:
+	return ret;
+}
+
+static void softing_initialize_timestamp(struct softing *card)
+{
+	uint64_t ovf;
+
+	card->ts_ref = ktime_get();
+
+	/* 16MHz is the reference */
+	ovf = 0x100000000ULL * 16;
+	do_div(ovf, card->pdat->freq ?: 16);
+
+	card->ts_overflow = ktime_add_us(ktime_set(0, 0), ovf);
+}
+
+ktime_t softing_raw2ktime(struct softing *card, u32 raw)
+{
+	uint64_t rawl;
+	ktime_t now, real_offset;
+	ktime_t target;
+	ktime_t tmp;
+
+	now = ktime_get();
+	real_offset = ktime_sub(ktime_get_real(), now);
+
+	/* find nsec from card */
+	rawl = raw * 16;
+	do_div(rawl, card->pdat->freq ?: 16);
+	target = ktime_add_us(card->ts_ref, rawl);
+	/* test for overflows */
+	tmp = ktime_add(target, card->ts_overflow);
+	while (unlikely(ktime_to_ns(tmp) > ktime_to_ns(now))) {
+		card->ts_ref = ktime_add(card->ts_ref, card->ts_overflow);
+		target = tmp;
+		tmp = ktime_add(target, card->ts_overflow);
+	}
+	return ktime_add(target, real_offset);
+}
+
+static inline int softing_error_reporting(struct net_device *netdev)
+{
+	struct softing_priv *priv = netdev_priv(netdev);
+
+	return (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)
+		? 1 : 0;
+}
+
+int softing_startstop(struct net_device *dev, int up)
+{
+	int ret;
+	struct softing *card;
+	struct softing_priv *priv;
+	struct net_device *netdev;
+	int bus_bitmask_start;
+	int j, error_reporting;
+	struct can_frame msg;
+	const struct can_bittiming *bt;
+
+	priv = netdev_priv(dev);
+	card = priv->card;
+
+	if (!card->fw.up)
+		return -EIO;
+
+	ret = mutex_lock_interruptible(&card->fw.lock);
+	if (ret)
+		return ret;
+
+	bus_bitmask_start = 0;
+	if (dev && up)
+		/* prepare to start this bus as well */
+		bus_bitmask_start |= (1 << priv->index);
+	/* bring netdevs down */
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		netdev = card->net[j];
+		if (!netdev)
+			continue;
+		priv = netdev_priv(netdev);
+
+		if (dev != netdev)
+			netif_stop_queue(netdev);
+
+		if (netif_running(netdev)) {
+			if (dev != netdev)
+				bus_bitmask_start |= (1 << j);
+			priv->tx.pending = 0;
+			priv->tx.echo_put = 0;
+			priv->tx.echo_get = 0;
+			/*
+			 * this bus' may just have called open_candev()
+			 * which is rather stupid to call close_candev()
+			 * already
+			 * but we may come here from busoff recovery too
+			 * in which case the echo_skb _needs_ flushing too.
+			 * just be sure to call open_candev() again
+			 */
+			close_candev(netdev);
+		}
+		priv->can.state = CAN_STATE_STOPPED;
+	}
+	card->tx.pending = 0;
+
+	softing_enable_irq(card, 0);
+	ret = softing_reset_chip(card);
+	if (ret)
+		goto failed;
+	if (!bus_bitmask_start)
+		/* no busses to be brought up */
+		goto card_done;
+
+	if ((bus_bitmask_start & 1) && (bus_bitmask_start & 2)
+			&& (softing_error_reporting(card->net[0])
+				!= softing_error_reporting(card->net[1]))) {
+		dev_alert(&card->pdev->dev,
+				"err_reporting flag differs for busses\n");
+		goto invalid;
+	}
+	error_reporting = 0;
+	if (bus_bitmask_start & 1) {
+		netdev = card->net[0];
+		priv = netdev_priv(netdev);
+		error_reporting += softing_error_reporting(netdev);
+		/* init chip 1 */
+		bt = &priv->can.bittiming;
+		iowrite16(bt->brp, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(bt->sjw, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		iowrite16(bt->phase_seg1 + bt->prop_seg,
+				&card->dpram[DPRAM_FCT_PARAM + 6]);
+		iowrite16(bt->phase_seg2, &card->dpram[DPRAM_FCT_PARAM + 8]);
+		iowrite16((priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) ? 1 : 0,
+				&card->dpram[DPRAM_FCT_PARAM + 10]);
+		ret = softing_fct_cmd(card, 1, "initialize_chip[0]");
+		if (ret < 0)
+			goto failed;
+		/* set mode */
+		iowrite16(0, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(0, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		ret = softing_fct_cmd(card, 3, "set_mode[0]");
+		if (ret < 0)
+			goto failed;
+		/* set filter */
+		/* 11bit id & mask */
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(0x07ff, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		/* 29bit id.lo & mask.lo & id.hi & mask.hi */
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 6]);
+		iowrite16(0xffff, &card->dpram[DPRAM_FCT_PARAM + 8]);
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 10]);
+		iowrite16(0x1fff, &card->dpram[DPRAM_FCT_PARAM + 12]);
+		ret = softing_fct_cmd(card, 7, "set_filter[0]");
+		if (ret < 0)
+			goto failed;
+		/* set output control */
+		iowrite16(priv->output, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		ret = softing_fct_cmd(card, 5, "set_output[0]");
+		if (ret < 0)
+			goto failed;
+	}
+	if (bus_bitmask_start & 2) {
+		netdev = card->net[1];
+		priv = netdev_priv(netdev);
+		error_reporting += softing_error_reporting(netdev);
+		/* init chip2 */
+		bt = &priv->can.bittiming;
+		iowrite16(bt->brp, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(bt->sjw, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		iowrite16(bt->phase_seg1 + bt->prop_seg,
+				&card->dpram[DPRAM_FCT_PARAM + 6]);
+		iowrite16(bt->phase_seg2, &card->dpram[DPRAM_FCT_PARAM + 8]);
+		iowrite16((priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) ? 1 : 0,
+				&card->dpram[DPRAM_FCT_PARAM + 10]);
+		ret = softing_fct_cmd(card, 2, "initialize_chip[1]");
+		if (ret < 0)
+			goto failed;
+		/* set mode2 */
+		iowrite16(0, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(0, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		ret = softing_fct_cmd(card, 4, "set_mode[1]");
+		if (ret < 0)
+			goto failed;
+		/* set filter2 */
+		/* 11bit id & mask */
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		iowrite16(0x07ff, &card->dpram[DPRAM_FCT_PARAM + 4]);
+		/* 29bit id.lo & mask.lo & id.hi & mask.hi */
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 6]);
+		iowrite16(0xffff, &card->dpram[DPRAM_FCT_PARAM + 8]);
+		iowrite16(0x0000, &card->dpram[DPRAM_FCT_PARAM + 10]);
+		iowrite16(0x1fff, &card->dpram[DPRAM_FCT_PARAM + 12]);
+		ret = softing_fct_cmd(card, 8, "set_filter[1]");
+		if (ret < 0)
+			goto failed;
+		/* set output control2 */
+		iowrite16(priv->output, &card->dpram[DPRAM_FCT_PARAM + 2]);
+		ret = softing_fct_cmd(card, 6, "set_output[1]");
+		if (ret < 0)
+			goto failed;
+	}
+	/* enable_error_frame */
+	/*
+	 * Error reporting is switched off at the moment since
+	 * the receiving of them is not yet 100% verified
+	 * This should be enabled sooner or later
+	 *
+	if (error_reporting) {
+		ret = softing_fct_cmd(card, 51, "enable_error_frame");
+		if (ret < 0)
+			goto failed;
+	}
+	*/
+	/* initialize interface */
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 2]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 4]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 6]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 8]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 10]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 12]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 14]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 16]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 18]);
+	iowrite16(1, &card->dpram[DPRAM_FCT_PARAM + 20]);
+	ret = softing_fct_cmd(card, 17, "initialize_interface");
+	if (ret < 0)
+		goto failed;
+	/* enable_fifo */
+	ret = softing_fct_cmd(card, 36, "enable_fifo");
+	if (ret < 0)
+		goto failed;
+	/* enable fifo tx ack */
+	ret = softing_fct_cmd(card, 13, "fifo_tx_ack[0]");
+	if (ret < 0)
+		goto failed;
+	/* enable fifo tx ack2 */
+	ret = softing_fct_cmd(card, 14, "fifo_tx_ack[1]");
+	if (ret < 0)
+		goto failed;
+	/* start_chip */
+	ret = softing_fct_cmd(card, 11, "start_chip");
+	if (ret < 0)
+		goto failed;
+	iowrite8(0, &card->dpram[DPRAM_INFO_BUSSTATE]);
+	iowrite8(0, &card->dpram[DPRAM_INFO_BUSSTATE2]);
+	if (card->pdat->generation < 2) {
+		iowrite8(0, &card->dpram[DPRAM_V2_IRQ_TOHOST]);
+		/* flush the DPRAM caches */
+		wmb();
+	}
+
+	softing_initialize_timestamp(card);
+
+	/*
+	 * do socketcan notifications/status changes
+	 * from here, no errors should occur, or the failed: part
+	 * must be reviewed
+	 */
+	memset(&msg, 0, sizeof(msg));
+	msg.can_id = CAN_ERR_FLAG | CAN_ERR_RESTARTED;
+	msg.can_dlc = CAN_ERR_DLC;
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		if (!(bus_bitmask_start & (1 << j)))
+			continue;
+		netdev = card->net[j];
+		if (!netdev)
+			continue;
+		priv = netdev_priv(netdev);
+		priv->can.state = CAN_STATE_ERROR_ACTIVE;
+		open_candev(netdev);
+		if (dev != netdev) {
+			/* notify other busses on the restart */
+			softing_netdev_rx(netdev, &msg, ktime_set(0, 0));
+			++priv->can.can_stats.restarts;
+		}
+		netif_wake_queue(netdev);
+	}
+
+	/* enable interrupts */
+	ret = softing_enable_irq(card, 1);
+	if (ret)
+		goto failed;
+card_done:
+	mutex_unlock(&card->fw.lock);
+	return 0;
+invalid:
+	ret = -EINVAL;
+failed:
+	softing_enable_irq(card, 0);
+	softing_reset_chip(card);
+	mutex_unlock(&card->fw.lock);
+	/* bring all other interfaces down */
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		netdev = card->net[j];
+		if (!netdev)
+			continue;
+		dev_close(netdev);
+	}
+	return ret;
+}
+
+int softing_default_output(struct net_device *netdev)
+{
+	struct softing_priv *priv = netdev_priv(netdev);
+	struct softing *card = priv->card;
+
+	switch (priv->chip) {
+	case 1000:
+		return (card->pdat->generation < 2) ? 0xfb : 0xfa;
+	case 5:
+		return 0x60;
+	default:
+		return 0x40;
+	}
+}
+
diff --git a/drivers/net/can/softing/softing_main.c b/drivers/net/can/softing/softing_main.c
new file mode 100644
index 0000000..5157e15
--- /dev/null
+++ b/drivers/net/can/softing/softing_main.c
@@ -0,0 +1,893 @@
+/*
+ * Copyright (C) 2008-2010
+ *
+ * - Kurt Van Dijck, EIA Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include "softing.h"
+
+#define TX_ECHO_SKB_MAX (((TXMAX+1)/2)-1)
+
+/*
+ * test is a specific CAN netdev
+ * is online (ie. up 'n running, not sleeping, not busoff
+ */
+static inline int canif_is_active(struct net_device *netdev)
+{
+	struct can_priv *can = netdev_priv(netdev);
+
+	if (!netif_running(netdev))
+		return 0;
+	return (can->state <= CAN_STATE_ERROR_PASSIVE);
+}
+
+/* reset DPRAM */
+static inline void softing_set_reset_dpram(struct softing *card)
+{
+	if (card->pdat->generation >= 2) {
+		spin_lock_bh(&card->spin);
+		iowrite8(ioread8(&card->dpram[DPRAM_V2_RESET]) & ~1,
+				&card->dpram[DPRAM_V2_RESET]);
+		spin_unlock_bh(&card->spin);
+	}
+}
+
+static inline void softing_clr_reset_dpram(struct softing *card)
+{
+	if (card->pdat->generation >= 2) {
+		spin_lock_bh(&card->spin);
+		iowrite8(ioread8(&card->dpram[DPRAM_V2_RESET]) | 1,
+				&card->dpram[DPRAM_V2_RESET]);
+		spin_unlock_bh(&card->spin);
+	}
+}
+
+/* trigger the tx queue-ing */
+static netdev_tx_t softing_netdev_start_xmit(struct sk_buff *skb,
+		struct net_device *dev)
+{
+	struct softing_priv *priv = netdev_priv(dev);
+	struct softing *card = priv->card;
+	int ret;
+	uint8_t *ptr;
+	uint8_t fifo_wr, fifo_rd;
+	struct can_frame *cf = (struct can_frame *)skb->data;
+	uint8_t buf[DPRAM_TX_SIZE];
+
+	if (can_dropped_invalid_skb(dev, skb))
+		return NETDEV_TX_OK;
+
+	spin_lock(&card->spin);
+
+	ret = NETDEV_TX_BUSY;
+	if (!card->fw.up ||
+			(card->tx.pending >= TXMAX) ||
+			(priv->tx.pending >= TX_ECHO_SKB_MAX))
+		goto xmit_done;
+	fifo_wr = ioread8(&card->dpram[DPRAM_TX_WR]);
+	fifo_rd = ioread8(&card->dpram[DPRAM_TX_RD]);
+	if (fifo_wr == fifo_rd)
+		/* fifo full */
+		goto xmit_done;
+	memset(buf, 0, sizeof(buf));
+	ptr = buf;
+	*ptr = CMD_TX;
+	if (cf->can_id & CAN_RTR_FLAG)
+		*ptr |= CMD_RTR;
+	if (cf->can_id & CAN_EFF_FLAG)
+		*ptr |= CMD_XTD;
+	if (priv->index)
+		*ptr |= CMD_BUS2;
+	++ptr;
+	*ptr++ = cf->can_dlc;
+	*ptr++ = (cf->can_id >> 0);
+	*ptr++ = (cf->can_id >> 8);
+	if (cf->can_id & CAN_EFF_FLAG) {
+		*ptr++ = (cf->can_id >> 16);
+		*ptr++ = (cf->can_id >> 24);
+	} else {
+		/* increment 1, not 2 as you might think */
+		ptr += 1;
+	}
+	if (!(cf->can_id & CAN_RTR_FLAG))
+		memcpy(ptr, &cf->data[0], cf->can_dlc);
+	memcpy_toio(&card->dpram[DPRAM_TX + DPRAM_TX_SIZE * fifo_wr],
+			buf, DPRAM_TX_SIZE);
+	if (++fifo_wr >= DPRAM_TX_CNT)
+		fifo_wr = 0;
+	iowrite8(fifo_wr, &card->dpram[DPRAM_TX_WR]);
+	card->tx.last_bus = priv->index;
+	++card->tx.pending;
+	++priv->tx.pending;
+	can_put_echo_skb(skb, dev, priv->tx.echo_put);
+	++priv->tx.echo_put;
+	if (priv->tx.echo_put >= TX_ECHO_SKB_MAX)
+		priv->tx.echo_put = 0;
+	/* can_put_echo_skb() saves the skb, safe to return TX_OK */
+	ret = NETDEV_TX_OK;
+xmit_done:
+	spin_unlock(&card->spin);
+	if (card->tx.pending >= TXMAX) {
+		int j;
+		for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+			if (card->net[j])
+				netif_stop_queue(card->net[j]);
+		}
+	}
+	if (ret != NETDEV_TX_OK)
+		netif_stop_queue(dev);
+
+	return ret;
+}
+
+/*
+ * shortcut for skb delivery
+ */
+int softing_netdev_rx(struct net_device *netdev, const struct can_frame *msg,
+		ktime_t ktime)
+{
+	struct sk_buff *skb;
+	struct can_frame *cf;
+
+	skb = alloc_can_skb(netdev, &cf);
+	if (!skb)
+		return -ENOMEM;
+	memcpy(cf, msg, sizeof(*msg));
+	skb->tstamp = ktime;
+	return netif_rx(skb);
+}
+
+/*
+ * softing_handle_1
+ * pop 1 entry from the DPRAM queue, and process
+ */
+static int softing_handle_1(struct softing *card)
+{
+	struct net_device *netdev;
+	struct softing_priv *priv;
+	ktime_t ktime;
+	struct can_frame msg;
+	int cnt = 0, lost_msg;
+	uint8_t fifo_rd, fifo_wr, cmd;
+	uint8_t *ptr;
+	uint32_t tmp_u32;
+	uint8_t buf[DPRAM_RX_SIZE];
+
+	memset(&msg, 0, sizeof(msg));
+	/* test for lost msgs */
+	lost_msg = ioread8(&card->dpram[DPRAM_RX_LOST]);
+	if (lost_msg) {
+		int j;
+		/* reset condition */
+		iowrite8(0, &card->dpram[DPRAM_RX_LOST]);
+		/* prepare msg */
+		msg.can_id = CAN_ERR_FLAG | CAN_ERR_CRTL;
+		msg.can_dlc = CAN_ERR_DLC;
+		msg.data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+		/*
+		 * service to all busses, we don't know which it was applicable
+		 * but only service busses that are online
+		 */
+		for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+			netdev = card->net[j];
+			if (!netdev)
+				continue;
+			if (!canif_is_active(netdev))
+				/* a dead bus has no overflows */
+				continue;
+			++netdev->stats.rx_over_errors;
+			softing_netdev_rx(netdev, &msg, ktime_set(0, 0));
+		}
+		/* prepare for other use */
+		memset(&msg, 0, sizeof(msg));
+		++cnt;
+	}
+
+	fifo_rd = ioread8(&card->dpram[DPRAM_RX_RD]);
+	fifo_wr = ioread8(&card->dpram[DPRAM_RX_WR]);
+
+	if (++fifo_rd >= DPRAM_RX_CNT)
+		fifo_rd = 0;
+	if (fifo_wr == fifo_rd)
+		return cnt;
+
+	memcpy_fromio(buf, &card->dpram[DPRAM_RX + DPRAM_RX_SIZE*fifo_rd],
+			DPRAM_RX_SIZE);
+	mb();
+	/* trigger dual port RAM */
+	iowrite8(fifo_rd, &card->dpram[DPRAM_RX_RD]);
+
+	ptr = buf;
+	cmd = *ptr++;
+	if (cmd == 0xff)
+		/* not quite usefull, probably the card has got out */
+		return 0;
+	netdev = card->net[0];
+	if (cmd & CMD_BUS2)
+		netdev = card->net[1];
+	priv = netdev_priv(netdev);
+
+	if (cmd & CMD_ERR) {
+		uint8_t can_state, state;
+
+		state = *ptr++;
+
+		msg.can_id = CAN_ERR_FLAG;
+		msg.can_dlc = CAN_ERR_DLC;
+
+		if (state & SF_MASK_BUSOFF) {
+			can_state = CAN_STATE_BUS_OFF;
+			msg.can_id |= CAN_ERR_BUSOFF;
+			state = STATE_BUSOFF;
+		} else if (state & SF_MASK_EPASSIVE) {
+			can_state = CAN_STATE_ERROR_PASSIVE;
+			msg.can_id |= CAN_ERR_CRTL;
+			msg.data[1] = CAN_ERR_CRTL_TX_PASSIVE;
+			state = STATE_EPASSIVE;
+		} else {
+			can_state = CAN_STATE_ERROR_ACTIVE;
+			msg.can_id |= CAN_ERR_CRTL;
+			state = STATE_EACTIVE;
+		}
+		/* update DPRAM */
+		iowrite8(state, &card->dpram[priv->index ?
+				DPRAM_INFO_BUSSTATE2 : DPRAM_INFO_BUSSTATE]);
+		/* timestamp */
+		tmp_u32 = le32_to_cpup((void *)ptr);
+		ptr += 4;
+		ktime = softing_raw2ktime(card, tmp_u32);
+
+		++netdev->stats.rx_errors;
+		/* update internal status */
+		if (can_state != priv->can.state) {
+			priv->can.state = can_state;
+			if (can_state == CAN_STATE_ERROR_PASSIVE)
+				++priv->can.can_stats.error_passive;
+			else if (can_state == CAN_STATE_BUS_OFF) {
+				/* this calls can_close_cleanup() */
+				can_bus_off(netdev);
+				netif_stop_queue(netdev);
+			}
+			/* trigger socketcan */
+			softing_netdev_rx(netdev, &msg, ktime);
+		}
+
+	} else {
+		if (cmd & CMD_RTR)
+			msg.can_id |= CAN_RTR_FLAG;
+		msg.can_dlc = get_can_dlc(*ptr++);
+		if (cmd & CMD_XTD) {
+			msg.can_id |= CAN_EFF_FLAG;
+			msg.can_id |= le32_to_cpup((void *)ptr);
+			ptr += 4;
+		} else {
+			msg.can_id |= le16_to_cpup((void *)ptr);
+			ptr += 2;
+		}
+		/* timestamp */
+		tmp_u32 = le32_to_cpup((void *)ptr);
+		ptr += 4;
+		ktime = softing_raw2ktime(card, tmp_u32);
+		if (!(msg.can_id & CAN_RTR_FLAG))
+			memcpy(&msg.data[0], ptr, 8);
+		ptr += 8;
+		/* update socket */
+		if (cmd & CMD_ACK) {
+			/* acknowledge, was tx msg */
+			struct sk_buff *skb;
+			skb = priv->can.echo_skb[priv->tx.echo_get];
+			if (skb)
+				skb->tstamp = ktime;
+			can_get_echo_skb(netdev, priv->tx.echo_get);
+			++priv->tx.echo_get;
+			if (priv->tx.echo_get >= TX_ECHO_SKB_MAX)
+				priv->tx.echo_get = 0;
+			if (priv->tx.pending)
+				--priv->tx.pending;
+			if (card->tx.pending)
+				--card->tx.pending;
+			++netdev->stats.tx_packets;
+			if (!(msg.can_id & CAN_RTR_FLAG))
+				netdev->stats.tx_bytes += msg.can_dlc;
+		} else {
+			int ret;
+
+			ret = softing_netdev_rx(netdev, &msg, ktime);
+			if (ret == NET_RX_SUCCESS) {
+				++netdev->stats.rx_packets;
+				if (!(msg.can_id & CAN_RTR_FLAG))
+					netdev->stats.rx_bytes += msg.can_dlc;
+			} else {
+				++netdev->stats.rx_dropped;
+			}
+		}
+	}
+	++cnt;
+	return cnt;
+}
+
+/*
+ * real interrupt handler
+ */
+static irqreturn_t softing_irq_thread(int irq, void *dev_id)
+{
+	struct softing *card = (struct softing *)dev_id;
+	struct net_device *netdev;
+	struct softing_priv *priv;
+	int j, offset, work_done;
+
+	work_done = 0;
+	spin_lock_bh(&card->spin);
+	while (softing_handle_1(card) > 0) {
+		++card->irq.svc_count;
+		++work_done;
+	}
+	spin_unlock_bh(&card->spin);
+	/* resume tx queue's */
+	offset = card->tx.last_bus;
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		if (card->tx.pending >= TXMAX)
+			break;
+		netdev = card->net[(j + offset + 1) % card->pdat->nbus];
+		if (!netdev)
+			continue;
+		priv = netdev_priv(netdev);
+		if (!canif_is_active(netdev))
+			/* it makes no sense to wake dead busses */
+			continue;
+		if (priv->tx.pending >= TX_ECHO_SKB_MAX)
+			continue;
+		++work_done;
+		netif_wake_queue(netdev);
+	}
+	return work_done ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/*
+ * interrupt routines:
+ * schedule the 'real interrupt handler'
+ */
+static irqreturn_t softing_irq_v2(int irq, void *dev_id)
+{
+	struct softing *card = (struct softing *)dev_id;
+	uint8_t ir;
+
+	ir = ioread8(&card->dpram[DPRAM_V2_IRQ_TOHOST]);
+	iowrite8(0, &card->dpram[DPRAM_V2_IRQ_TOHOST]);
+	return (1 == ir) ? IRQ_WAKE_THREAD : IRQ_NONE;
+}
+
+static irqreturn_t softing_irq_v1(int irq, void *dev_id)
+{
+	struct softing *card = (struct softing *)dev_id;
+	uint8_t ir;
+
+	ir = ioread8(&card->dpram[DPRAM_IRQ_TOHOST]);
+	iowrite8(0, &card->dpram[DPRAM_IRQ_TOHOST]);
+	return ir ? IRQ_WAKE_THREAD : IRQ_NONE;
+}
+
+/*
+ * netdev/candev inter-operability
+ */
+static int softing_netdev_open(struct net_device *ndev)
+{
+	int ret;
+
+	/* check or determine and set bittime */
+	ret = open_candev(ndev);
+	if (!ret)
+		ret = softing_startstop(ndev, 1);
+	return ret;
+}
+
+static int softing_netdev_stop(struct net_device *ndev)
+{
+	int ret;
+
+	netif_stop_queue(ndev);
+
+	/* softing cycle does close_candev() */
+	ret = softing_startstop(ndev, 0);
+	return ret;
+}
+
+static int softing_candev_set_mode(struct net_device *ndev, enum can_mode mode)
+{
+	int ret;
+
+	switch (mode) {
+	case CAN_MODE_START:
+		/* softing_startstop does close_candev() */
+		ret = softing_startstop(ndev, 1);
+		return ret;
+	case CAN_MODE_STOP:
+	case CAN_MODE_SLEEP:
+		return -EOPNOTSUPP;
+	}
+	return 0;
+}
+
+/*
+ * Softing device management helpers
+ */
+int softing_enable_irq(struct softing *card, int enable)
+{
+	int ret;
+
+	if (!card->irq.nr) {
+		return 0;
+	} else if (card->irq.requested && !enable) {
+		free_irq(card->irq.nr, card);
+		card->irq.requested = 0;
+	} else if (!card->irq.requested && enable) {
+		ret = request_threaded_irq(card->irq.nr,
+				(card->pdat->generation >= 2) ?
+					softing_irq_v2 : softing_irq_v1,
+				softing_irq_thread, IRQF_SHARED,
+				dev_name(&card->pdev->dev), card);
+		if (ret) {
+			dev_alert(&card->pdev->dev,
+					"request_threaded_irq(%u) failed\n",
+					card->irq.nr);
+			return ret;
+		}
+		card->irq.requested = 1;
+	}
+	return 0;
+}
+
+static void softing_card_shutdown(struct softing *card)
+{
+	int fw_up = 0;
+
+	if (mutex_lock_interruptible(&card->fw.lock))
+		/* return -ERESTARTSYS */;
+	fw_up = card->fw.up;
+	card->fw.up = 0;
+
+	if (card->irq.requested && card->irq.nr) {
+		free_irq(card->irq.nr, card);
+		card->irq.requested = 0;
+	}
+	if (fw_up) {
+		if (card->pdat->enable_irq)
+			card->pdat->enable_irq(card->pdev, 0);
+		softing_set_reset_dpram(card);
+		if (card->pdat->reset)
+			card->pdat->reset(card->pdev, 1);
+	}
+	mutex_unlock(&card->fw.lock);
+}
+
+static __devinit int softing_card_boot(struct softing *card)
+{
+	int ret, j;
+	static const uint8_t stream[] = {
+		0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, };
+	unsigned char back[sizeof(stream)];
+
+	if (mutex_lock_interruptible(&card->fw.lock))
+		return -ERESTARTSYS;
+	if (card->fw.up) {
+		mutex_unlock(&card->fw.lock);
+		return 0;
+	}
+	/* reset board */
+	if (card->pdat->enable_irq)
+		card->pdat->enable_irq(card->pdev, 1);
+	/* boot card */
+	softing_set_reset_dpram(card);
+	if (card->pdat->reset)
+		card->pdat->reset(card->pdev, 1);
+	for (j = 0; (j + sizeof(stream)) < card->dpram_size;
+			j += sizeof(stream)) {
+
+		memcpy_toio(&card->dpram[j], stream, sizeof(stream));
+		/* flush IO cache */
+		mb();
+		memcpy_fromio(back, &card->dpram[j], sizeof(stream));
+
+		if (!memcmp(back, stream, sizeof(stream)))
+			continue;
+		/* memory is not equal */
+		dev_alert(&card->pdev->dev, "dpram failed at 0x%04x\n", j);
+		ret = -EIO;
+		goto failed;
+	}
+	wmb();
+	/* load boot firmware */
+	ret = softing_load_fw(card->pdat->boot.fw, card, card->dpram,
+				card->dpram_size,
+				card->pdat->boot.offs - card->pdat->boot.addr);
+	if (ret < 0)
+		goto failed;
+	/* load loader firmware */
+	ret = softing_load_fw(card->pdat->load.fw, card, card->dpram,
+				card->dpram_size,
+				card->pdat->load.offs - card->pdat->load.addr);
+	if (ret < 0)
+		goto failed;
+
+	if (card->pdat->reset)
+		card->pdat->reset(card->pdev, 0);
+	softing_clr_reset_dpram(card);
+	ret = softing_bootloader_command(card, 0, "card boot");
+	if (ret < 0)
+		goto failed;
+	ret = softing_load_app_fw(card->pdat->app.fw, card);
+	if (ret < 0)
+		goto failed;
+
+	ret = softing_chip_poweron(card);
+	if (ret < 0)
+		goto failed;
+
+	card->fw.up = 1;
+	mutex_unlock(&card->fw.lock);
+	return 0;
+failed:
+	card->fw.up = 0;
+	if (card->pdat->enable_irq)
+		card->pdat->enable_irq(card->pdev, 0);
+	softing_set_reset_dpram(card);
+	if (card->pdat->reset)
+		card->pdat->reset(card->pdev, 1);
+	mutex_unlock(&card->fw.lock);
+	return ret;
+}
+
+/*
+ * netdev sysfs
+ */
+static ssize_t show_channel(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct net_device *ndev = to_net_dev(dev);
+	struct softing_priv *priv = netdev2softing(ndev);
+
+	return sprintf(buf, "%i\n", priv->index);
+}
+
+static ssize_t show_chip(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct net_device *ndev = to_net_dev(dev);
+	struct softing_priv *priv = netdev2softing(ndev);
+
+	return sprintf(buf, "%i\n", priv->chip);
+}
+
+static ssize_t show_output(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct net_device *ndev = to_net_dev(dev);
+	struct softing_priv *priv = netdev2softing(ndev);
+
+	return sprintf(buf, "0x%02x\n", priv->output);
+}
+
+static ssize_t store_output(struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
+{
+	struct net_device *ndev = to_net_dev(dev);
+	struct softing_priv *priv = netdev2softing(ndev);
+	struct softing *card = priv->card;
+	unsigned long val;
+	int ret;
+
+	ret = strict_strtoul(buf, 0, &val);
+	if (ret < 0)
+		return ret;
+	val &= 0xFF;
+
+	ret = mutex_lock_interruptible(&card->fw.lock);
+	if (ret)
+		return -ERESTARTSYS;
+	if (netif_running(ndev)) {
+		mutex_unlock(&card->fw.lock);
+		return -EBUSY;
+	}
+	priv->output = val;
+	mutex_unlock(&card->fw.lock);
+	return count;
+}
+
+static const DEVICE_ATTR(channel, S_IRUGO, show_channel, NULL);
+static const DEVICE_ATTR(chip, S_IRUGO, show_chip, NULL);
+static const DEVICE_ATTR(output, S_IRUGO | S_IWUSR, show_output, store_output);
+
+static const struct attribute *const netdev_sysfs_attrs[] = {
+	&dev_attr_channel.attr,
+	&dev_attr_chip.attr,
+	&dev_attr_output.attr,
+	NULL,
+};
+static const struct attribute_group netdev_sysfs_group = {
+	.name = NULL,
+	.attrs = (struct attribute **)netdev_sysfs_attrs,
+};
+
+static const struct net_device_ops softing_netdev_ops = {
+	.ndo_open = softing_netdev_open,
+	.ndo_stop = softing_netdev_stop,
+	.ndo_start_xmit	= softing_netdev_start_xmit,
+};
+
+static const struct can_bittiming_const softing_btr_const = {
+	.tseg1_min = 1,
+	.tseg1_max = 16,
+	.tseg2_min = 1,
+	.tseg2_max = 8,
+	.sjw_max = 4, /* overruled */
+	.brp_min = 1,
+	.brp_max = 32, /* overruled */
+	.brp_inc = 1,
+};
+
+
+static __devinit struct net_device *softing_netdev_create(struct softing *card,
+		uint16_t chip_id)
+{
+	struct net_device *netdev;
+	struct softing_priv *priv;
+
+	netdev = alloc_candev(sizeof(*priv), TX_ECHO_SKB_MAX);
+	if (!netdev) {
+		dev_alert(&card->pdev->dev, "alloc_candev failed\n");
+		return NULL;
+	}
+	priv = netdev_priv(netdev);
+	priv->netdev = netdev;
+	priv->card = card;
+	memcpy(&priv->btr_const, &softing_btr_const, sizeof(priv->btr_const));
+	priv->btr_const.brp_max = card->pdat->max_brp;
+	priv->btr_const.sjw_max = card->pdat->max_sjw;
+	priv->can.bittiming_const = &priv->btr_const;
+	priv->can.clock.freq = 8000000;
+	priv->chip = chip_id;
+	priv->output = softing_default_output(netdev);
+	SET_NETDEV_DEV(netdev, &card->pdev->dev);
+
+	netdev->flags |= IFF_ECHO;
+	netdev->netdev_ops = &softing_netdev_ops;
+	priv->can.do_set_mode = softing_candev_set_mode;
+	priv->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES;
+
+	return netdev;
+}
+
+static __devinit int softing_netdev_register(struct net_device *netdev)
+{
+	int ret;
+
+	netdev->sysfs_groups[0] = &netdev_sysfs_group;
+	ret = register_candev(netdev);
+	if (ret) {
+		dev_alert(&netdev->dev, "register failed\n");
+		return ret;
+	}
+	return 0;
+}
+
+static void softing_netdev_cleanup(struct net_device *netdev)
+{
+	unregister_candev(netdev);
+	free_candev(netdev);
+}
+
+/*
+ * sysfs for Platform device
+ */
+#define DEV_ATTR_RO(name, member) \
+static ssize_t show_##name(struct device *dev, \
+		struct device_attribute *attr, char *buf) \
+{ \
+	struct softing *card = platform_get_drvdata(to_platform_device(dev)); \
+	return sprintf(buf, "%u\n", card->member); \
+} \
+static DEVICE_ATTR(name, 0444, show_##name, NULL)
+
+#define DEV_ATTR_RO_STR(name, member) \
+static ssize_t show_##name(struct device *dev, \
+		struct device_attribute *attr, char *buf) \
+{ \
+	struct softing *card = platform_get_drvdata(to_platform_device(dev)); \
+	return sprintf(buf, "%s\n", card->member); \
+} \
+static DEVICE_ATTR(name, 0444, show_##name, NULL)
+
+DEV_ATTR_RO(serial, id.serial);
+DEV_ATTR_RO_STR(firmware, pdat->app.fw);
+DEV_ATTR_RO(firmware_version, id.fw_version);
+DEV_ATTR_RO_STR(hardware, pdat->name);
+DEV_ATTR_RO(hardware_version, id.hw_version);
+DEV_ATTR_RO(license, id.license);
+DEV_ATTR_RO(frequency, id.freq);
+DEV_ATTR_RO(txpending, tx.pending);
+
+static struct attribute *softing_pdev_attrs[] = {
+	&dev_attr_serial.attr,
+	&dev_attr_firmware.attr,
+	&dev_attr_firmware_version.attr,
+	&dev_attr_hardware.attr,
+	&dev_attr_hardware_version.attr,
+	&dev_attr_license.attr,
+	&dev_attr_frequency.attr,
+	&dev_attr_txpending.attr,
+	NULL,
+};
+
+static const struct attribute_group softing_pdev_group = {
+	.name = NULL,
+	.attrs = softing_pdev_attrs,
+};
+
+/*
+ * platform driver
+ */
+static __devexit int softing_pdev_remove(struct platform_device *pdev)
+{
+	struct softing *card = platform_get_drvdata(pdev);
+	int j;
+
+	/* first, disable card*/
+	softing_card_shutdown(card);
+
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		if (!card->net[j])
+			continue;
+		softing_netdev_cleanup(card->net[j]);
+		card->net[j] = NULL;
+	}
+	sysfs_remove_group(&pdev->dev.kobj, &softing_pdev_group);
+
+	iounmap(card->dpram);
+	kfree(card);
+	return 0;
+}
+
+static __devinit int softing_pdev_probe(struct platform_device *pdev)
+{
+	const struct softing_platform_data *pdat = pdev->dev.platform_data;
+	struct softing *card;
+	struct net_device *netdev;
+	struct softing_priv *priv;
+	struct resource *pres;
+	int ret;
+	int j;
+
+	if (!pdat) {
+		dev_warn(&pdev->dev, "no platform data\n");
+		return -EINVAL;
+	}
+	if (pdat->nbus > ARRAY_SIZE(card->net)) {
+		dev_warn(&pdev->dev, "%u nets??\n", pdat->nbus);
+		return -EINVAL;
+	}
+
+	card = kzalloc(sizeof(*card), GFP_KERNEL);
+	if (!card)
+		return -ENOMEM;
+	card->pdat = pdat;
+	card->pdev = pdev;
+	platform_set_drvdata(pdev, card);
+	mutex_init(&card->fw.lock);
+	spin_lock_init(&card->spin);
+
+	ret = -EINVAL;
+	pres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!pres)
+		goto platform_resource_failed;;
+	card->dpram_phys = pres->start;
+	card->dpram_size = pres->end - pres->start + 1;
+	card->dpram = ioremap_nocache(card->dpram_phys, card->dpram_size);
+	if (!card->dpram) {
+		dev_alert(&card->pdev->dev, "dpram ioremap failed\n");
+		goto ioremap_failed;
+	}
+
+	pres = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (pres)
+		card->irq.nr = pres->start;
+
+	/* reset card */
+	ret = softing_card_boot(card);
+	if (ret < 0) {
+		dev_alert(&pdev->dev, "failed to boot\n");
+		goto boot_failed;
+	}
+
+	/* only now, the chip's are known */
+	card->id.freq = card->pdat->freq;
+
+	ret = sysfs_create_group(&pdev->dev.kobj, &softing_pdev_group);
+	if (ret < 0) {
+		dev_alert(&card->pdev->dev, "sysfs failed\n");
+		goto sysfs_failed;
+	}
+
+	ret = -ENOMEM;
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		card->net[j] = netdev =
+			softing_netdev_create(card, card->id.chip[j]);
+		if (!netdev) {
+			dev_alert(&pdev->dev, "failed to make can[%i]", j);
+			goto netdev_failed;
+		}
+		priv = netdev_priv(card->net[j]);
+		priv->index = j;
+		ret = softing_netdev_register(netdev);
+		if (ret) {
+			free_candev(netdev);
+			card->net[j] = NULL;
+			dev_alert(&card->pdev->dev,
+					"failed to register can[%i]\n", j);
+			goto netdev_failed;
+		}
+	}
+	dev_info(&card->pdev->dev, "%s ready.\n", card->pdat->name);
+	return 0;
+
+netdev_failed:
+	for (j = 0; j < ARRAY_SIZE(card->net); ++j) {
+		if (!card->net[j])
+			continue;
+		softing_netdev_cleanup(card->net[j]);
+	}
+	sysfs_remove_group(&pdev->dev.kobj, &softing_pdev_group);
+sysfs_failed:
+	softing_card_shutdown(card);
+boot_failed:
+	iounmap(card->dpram);
+ioremap_failed:
+platform_resource_failed:
+	kfree(card);
+	return ret;
+}
+
+static struct platform_driver softing_driver = {
+	.driver = {
+		.name = "softing",
+		.owner = THIS_MODULE,
+	},
+	.probe = softing_pdev_probe,
+	.remove = __devexit_p(softing_pdev_remove),
+};
+
+MODULE_ALIAS("platform:softing");
+
+static int __init softing_start(void)
+{
+	return platform_driver_register(&softing_driver);
+}
+
+static void __exit softing_stop(void)
+{
+	platform_driver_unregister(&softing_driver);
+}
+
+module_init(softing_start);
+module_exit(softing_stop);
+
+MODULE_DESCRIPTION("Softing DPRAM CAN driver");
+MODULE_AUTHOR("Kurt Van Dijck <kurt.van.dijck-/BeEPy95v10@public.gmane.org>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/net/can/softing/softing_platform.h b/drivers/net/can/softing/softing_platform.h
new file mode 100644
index 0000000..d2471cd
--- /dev/null
+++ b/drivers/net/can/softing/softing_platform.h
@@ -0,0 +1,41 @@
+
+#include <linux/platform_device.h>
+
+#ifndef _SOFTING_DEVICE_H_
+#define _SOFTING_DEVICE_H_
+
+/* softing firmware directory prefix */
+#define fw_dir "softing-4.6/"
+
+struct softing_platform_data {
+	unsigned int manf;
+	unsigned int prod;
+	/*
+	 * generation
+	 * 1st with NEC or SJA1000
+	 * 8bit, exclusive interrupt, ...
+	 * 2nd only SJA1000
+	 * 16bit, shared interrupt
+	 */
+	int generation;
+	int nbus; /* # busses on device */
+	unsigned int freq; /* operating frequency in Hz */
+	unsigned int max_brp;
+	unsigned int max_sjw;
+	unsigned long dpram_size;
+	const char *name;
+	struct {
+		unsigned long offs;
+		unsigned long addr;
+		const char *fw;
+	} boot, load, app;
+	/*
+	 * reset() function
+	 * bring pdev in or out of reset, depending on value
+	 */
+	int (*reset)(struct platform_device *pdev, int value);
+	int (*enable_irq)(struct platform_device *pdev, int value);
+};
+
+#endif
+

[PATCH net-next-2.6 v3 2/2] can: add driver for Softing card

[Kurt Van Dijck]

This patch adds the driver that creates a platform:softing device
from a pcmcia_device
Note: the Kconfig indicates a dependency on the softing.ko driver,
but this is purely to make configuration intuitive. This driver will
work independent, but no CAN network devices appear until softing.ko is
loaded too.

Signed-off-by: Kurt Van Dijck <kurt.van.dijck-/BeEPy95v10@public.gmane.org>
Acked-by: Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>
---
 drivers/net/can/softing/Kconfig      |   14 ++
 drivers/net/can/softing/Makefile     |    1 +
 drivers/net/can/softing/softing_cs.c |  360 ++++++++++++++++++++++++++++++++++
 3 files changed, 375 insertions(+), 0 deletions(-)

diff --git a/drivers/net/can/softing/Kconfig b/drivers/net/can/softing/Kconfig
index 072f337..92bd6bd 100644
--- a/drivers/net/can/softing/Kconfig
+++ b/drivers/net/can/softing/Kconfig
@@ -14,3 +14,17 @@ config CAN_SOFTING
 	  controls the 2 busses on the card together.
 	  As such, some actions (start/stop/busoff recovery) on 1 bus
 	  must bring down the other bus too temporarily.
+
+config CAN_SOFTING_CS
+	tristate "Softing Gmbh CAN pcmcia cards"
+	depends on PCMCIA
+	select CAN_SOFTING
+	---help---
+	  Support for PCMCIA cards from Softing Gmbh & some cards
+	  from Vector Gmbh.
+	  You need firmware for these, which you can get at
+	  http://developer.berlios.de/projects/socketcan/
+	  This version of the driver is written against
+	  firmware version 4.6 (softing-fw-4.6-binaries.tar.gz)
+	  In order to use the card as CAN device, you need the Softing generic
+	  support too.
diff --git a/drivers/net/can/softing/Makefile b/drivers/net/can/softing/Makefile
index 7db0445..c5e5016 100644
--- a/drivers/net/can/softing/Makefile
+++ b/drivers/net/can/softing/Makefile
@@ -1,5 +1,6 @@
 
 softing-y := softing_main.o softing_fw.o
 obj-$(CONFIG_CAN_SOFTING) += softing.o
+obj-$(CONFIG_CAN_SOFTING_CS) += softing_cs.o
 
 ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
diff --git a/drivers/net/can/softing/softing_cs.c b/drivers/net/can/softing/softing_cs.c
new file mode 100644
index 0000000..eb54e30
--- /dev/null
+++ b/drivers/net/can/softing/softing_cs.c
@@ -0,0 +1,360 @@
+/*
+ * Copyright (C) 2008-2010
+ *
+ * - Kurt Van Dijck, EIA Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+#include "softing_platform.h"
+
+static int softingcs_index;
+static spinlock_t softingcs_index_lock;
+
+static int softingcs_reset(struct platform_device *pdev, int v);
+static int softingcs_enable_irq(struct platform_device *pdev, int v);
+
+/*
+ * platform_data descriptions
+ */
+#define MHZ (1000*1000)
+static const struct softing_platform_data softingcs_platform_data[] = {
+{
+	.name = "CANcard",
+	.manf = 0x0168, .prod = 0x001,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 16 * MHZ, .max_brp = 32, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "CANcard-NEC",
+	.manf = 0x0168, .prod = 0x002,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 16 * MHZ, .max_brp = 32, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "CANcard-SJA",
+	.manf = 0x0168, .prod = 0x004,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 20 * MHZ, .max_brp = 32, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cansja.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "CANcard-2",
+	.manf = 0x0168, .prod = 0x005,
+	.generation = 2,
+	.nbus = 2,
+	.freq = 24 * MHZ, .max_brp = 64, .max_sjw = 4,
+	.dpram_size = 0x1000,
+	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = NULL,
+}, {
+	.name = "Vector-CANcard",
+	.manf = 0x0168, .prod = 0x081,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 16 * MHZ, .max_brp = 64, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "Vector-CANcard-SJA",
+	.manf = 0x0168, .prod = 0x084,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 20 * MHZ, .max_brp = 32, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cansja.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "Vector-CANcard-2",
+	.manf = 0x0168, .prod = 0x085,
+	.generation = 2,
+	.nbus = 2,
+	.freq = 24 * MHZ, .max_brp = 64, .max_sjw = 4,
+	.dpram_size = 0x1000,
+	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = NULL,
+}, {
+	.name = "EDICcard-NEC",
+	.manf = 0x0168, .prod = 0x102,
+	.generation = 1,
+	.nbus = 2,
+	.freq = 16 * MHZ, .max_brp = 64, .max_sjw = 4,
+	.dpram_size = 0x0800,
+	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = softingcs_enable_irq,
+}, {
+	.name = "EDICcard-2",
+	.manf = 0x0168, .prod = 0x105,
+	.generation = 2,
+	.nbus = 2,
+	.freq = 24 * MHZ, .max_brp = 64, .max_sjw = 4,
+	.dpram_size = 0x1000,
+	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
+	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
+	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
+	.reset = softingcs_reset,
+	.enable_irq = NULL,
+}, {
+	0, 0,
+},
+};
+
+MODULE_FIRMWARE(fw_dir "bcard.bin");
+MODULE_FIRMWARE(fw_dir "ldcard.bin");
+MODULE_FIRMWARE(fw_dir "cancard.bin");
+MODULE_FIRMWARE(fw_dir "cansja.bin");
+
+MODULE_FIRMWARE(fw_dir "bcard2.bin");
+MODULE_FIRMWARE(fw_dir "ldcard2.bin");
+MODULE_FIRMWARE(fw_dir "cancrd2.bin");
+
+static __devinit const struct softing_platform_data
+*softingcs_find_platform_data(unsigned int manf, unsigned int prod)
+{
+	const struct softing_platform_data *lp;
+
+	for (lp = softingcs_platform_data; lp->manf; ++lp) {
+		if ((lp->manf == manf) && (lp->prod == prod))
+			return lp;
+	}
+	return NULL;
+}
+
+/*
+ * platformdata callbacks
+ */
+static int softingcs_reset(struct platform_device *pdev, int v)
+{
+	struct pcmcia_device *pcmcia = to_pcmcia_dev(pdev->dev.parent);
+
+	dev_dbg(&pdev->dev, "pcmcia config [2] %02x\n", v ? 0 : 0x20);
+	return pcmcia_write_config_byte(pcmcia, 2, v ? 0 : 0x20);
+}
+
+static int softingcs_enable_irq(struct platform_device *pdev, int v)
+{
+	struct pcmcia_device *pcmcia = to_pcmcia_dev(pdev->dev.parent);
+
+	dev_dbg(&pdev->dev, "pcmcia config [0] %02x\n", v ? 0x60 : 0);
+	return pcmcia_write_config_byte(pcmcia, 0, v ? 0x60 : 0);
+}
+
+/*
+ * pcmcia check
+ */
+static __devinit int softingcs_probe_config(struct pcmcia_device *pcmcia,
+		void *priv_data)
+{
+	struct softing_platform_data *pdat = priv_data;
+	struct resource *pres;
+	int memspeed = 0;
+
+	WARN_ON(!pdat);
+	pres = pcmcia->resource[PCMCIA_IOMEM_0];
+	if (resource_size(pres) < 0x1000)
+		return -ERANGE;
+
+	pres->flags |= WIN_MEMORY_TYPE_CM | WIN_ENABLE;
+	if (pdat->generation < 2) {
+		pres->flags |= WIN_USE_WAIT | WIN_DATA_WIDTH_8;
+		memspeed = 3;
+	} else {
+		pres->flags |= WIN_DATA_WIDTH_16;
+	}
+	return pcmcia_request_window(pcmcia, pres, memspeed);
+}
+
+static __devexit void softingcs_remove(struct pcmcia_device *pcmcia)
+{
+	struct platform_device *pdev = pcmcia->priv;
+
+	/* free bits */
+	platform_device_unregister(pdev);
+	/* release pcmcia stuff */
+	pcmcia_disable_device(pcmcia);
+}
+
+/*
+ * platform_device wrapper
+ * pdev->resource has 2 entries: io & irq
+ */
+static void softingcs_pdev_release(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	kfree(pdev);
+}
+
+static __devinit int softingcs_probe(struct pcmcia_device *pcmcia)
+{
+	int ret;
+	struct platform_device *pdev;
+	const struct softing_platform_data *pdat;
+	struct resource *pres;
+	struct dev {
+		struct platform_device pdev;
+		struct resource res[2];
+	} *dev;
+
+	/* find matching platform_data */
+	pdat = softingcs_find_platform_data(pcmcia->manf_id, pcmcia->card_id);
+	if (!pdat)
+		return -ENOTTY;
+
+	/* setup pcmcia device */
+	pcmcia->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IOMEM |
+		CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC;
+	ret = pcmcia_loop_config(pcmcia, softingcs_probe_config, (void *)pdat);
+	if (ret)
+		goto pcmcia_failed;
+
+	ret = pcmcia_enable_device(pcmcia);
+	if (ret < 0)
+		goto pcmcia_failed;
+
+	pres = pcmcia->resource[PCMCIA_IOMEM_0];
+	if (!pres) {
+		ret = -EBADF;
+		goto pcmcia_bad;
+	}
+
+	/* create softing platform device */
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev) {
+		ret = -ENOMEM;
+		goto mem_failed;
+	}
+	dev->pdev.resource = dev->res;
+	dev->pdev.num_resources = ARRAY_SIZE(dev->res);
+	dev->pdev.dev.release = softingcs_pdev_release;
+
+	pdev = &dev->pdev;
+	pdev->dev.platform_data = (void *)pdat;
+	pdev->dev.parent = &pcmcia->dev;
+	pcmcia->priv = pdev;
+
+	/* platform device resources */
+	pdev->resource[0].flags = IORESOURCE_MEM;
+	pdev->resource[0].start = pres->start;
+	pdev->resource[0].end = pres->end;
+
+	pdev->resource[1].flags = IORESOURCE_IRQ;
+	pdev->resource[1].start = pcmcia->irq;
+	pdev->resource[1].end = pdev->resource[1].start;
+
+	/* platform device setup */
+	spin_lock(&softingcs_index_lock);
+	pdev->id = softingcs_index++;
+	spin_unlock(&softingcs_index_lock);
+	pdev->name = "softing";
+	dev_set_name(&pdev->dev, "softingcs.%i", pdev->id);
+	ret = platform_device_register(pdev);
+	if (ret < 0)
+		goto platform_failed;
+
+	dev_info(&pcmcia->dev, "created %s\n", dev_name(&pdev->dev));
+	return 0;
+
+platform_failed:
+	kfree(dev);
+mem_failed:
+pcmcia_bad:
+pcmcia_failed:
+	pcmcia_disable_device(pcmcia);
+	pcmcia->priv = NULL;
+	return ret ?: -ENODEV;
+}
+
+static /*const*/ struct pcmcia_device_id softingcs_ids[] = {
+	/* softing */
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0001),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0002),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0004),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0005),
+	/* vector, manufacturer? */
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0081),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0084),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0085),
+	/* EDIC */
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0102),
+	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0105),
+	PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, softingcs_ids);
+
+static struct pcmcia_driver softingcs_driver = {
+	.owner		= THIS_MODULE,
+	.name		= "softingcs",
+	.id_table	= softingcs_ids,
+	.probe		= softingcs_probe,
+	.remove		= __devexit_p(softingcs_remove),
+};
+
+static int __init softingcs_start(void)
+{
+	spin_lock_init(&softingcs_index_lock);
+	return pcmcia_register_driver(&softingcs_driver);
+}
+
+static void __exit softingcs_stop(void)
+{
+	pcmcia_unregister_driver(&softingcs_driver);
+}
+
+module_init(softingcs_start);
+module_exit(softingcs_stop);
+
+MODULE_DESCRIPTION("softing CANcard driver"
+		", links PCMCIA card to softing driver");
+MODULE_LICENSE("GPL v2");
+

Re: [PATCH net-next-2.6 v3 2/2] can: add driver for Softing card

[Kurt Van Dijck]

Hi,

I didn't get any remarks anymore on this series.
Does this mean the PCMCIA interface is OK? I'm not so familiar
with that part...

regards,
Kurt

Re: [PATCH net-next-2.6 v3 0/2] can: add driver for Softing card

[David Miller]

From: Kurt Van Dijck <kurt.van.dijck-/BeEPy95v10@public.gmane.org>
Date: Tue, 11 Jan 2011 15:30:08 +0100

> This series will add a driver for Softing PCMCIA CAN card.

Both patches applied, thanks.