From: gene heskett <gheskett@wdtv.com>
To: linux-ide@vger.kernel.org
Cc: BU66ER BAD6ER <debu66er@gmail.com>
Subject: Re: Seagate hard disk firmware issue
Date: Sat, 30 Apr 2011 08:08:59 -0400 [thread overview]
Message-ID: <201104300808.59185.gheskett@wdtv.com> (raw)
In-Reply-To: <BANLkTim5m51Qx=wm+C1LhEG7dE4C-nkGOw@mail.gmail.com>
On Saturday, April 30, 2011 07:56:21 AM BU66ER BAD6ER did opine:
This <linux-ide@vger.kernel.org> is a mailing list. WTH when I click on
reply-to-list, do I always have to copy/paste the lists address in the To:
line? fscking PIMA!
More below, where it should be.
> Hi,
>
> Some time ago, I returned my hard disk and got a new one. Lately, I'm
> having performance issues again and I suspect there is a hardware
> error again like last time. If you could confirm this I would be most
> grateful.
>
> Thanks in advance!
>
> # smartctl -a /dev/sdb
> smartctl 5.41 2011-03-16 r3296
> [x86_64-unknown-linux-gnu-2.6.38-2-amd64] (local build)
> Copyright (C) 2002-11 by Bruce Allen,
> http://smartmontools.sourceforge.net
>
> === START OF INFORMATION SECTION ===
> Device Model: ST2000DL003-9VT166
> Serial Number: 5YD1YD5P
> Firmware Version: CC32
> User Capacity: 2,000,398,934,016 bytes
> Device is: Not in smartctl database [for details use: -P showall]
> ATA Version is: 8
> ATA Standard is: ATA-8-ACS revision 4
> Local Time is: Sat Apr 30 12:59:32 2011 CEST
> SMART support is: Available - device has SMART capability.
> SMART support is: Enabled
>
> === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
>
> General SMART Values:
> Offline data collection status: (0x82) Offline data collection activity
> was completed without error.
> Auto Offline Data Collection:
> Enabled. Self-test execution status: ( 0) The previous self-test
> routine completed without error or no self-test has ever been run.
> Total time to complete Offline
> data collection: ( 623) seconds.
> Offline data collection
> capabilities: (0x7b) SMART execute Offline immediate.
> Auto Offline data collection
> on/off support.
> Suspend Offline collection upon
> new command.
> Offline surface scan supported.
> Self-test supported.
> Conveyance Self-test supported.
> Selective Self-test supported.
> SMART capabilities: (0x0003) Saves SMART data before entering
> power-saving mode.
> Supports SMART auto save timer.
> Error logging capability: (0x01) Error logging supported.
> General Purpose Logging
> supported. Short self-test routine
> recommended polling time: ( 1) minutes.
> Extended self-test routine
> recommended polling time: ( 255) minutes.
> Conveyance self-test routine
> recommended polling time: ( 2) minutes.
> SCT capabilities: (0x30b7) SCT Status supported.
> SCT Feature Control supported.
> SCT Data Table supported.
>
> SMART Attributes Data Structure revision number: 10
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
> UPDATED WHEN_FAILED RAW_VALUE
> 1 Raw_Read_Error_Rate 0x000f 096 082 006 Pre-fail
> Always - 2447656
> 3 Spin_Up_Time 0x0003 097 092 000 Pre-fail
> Always - 0
> 4 Start_Stop_Count 0x0032 100 100 020 Old_age
> Always - 265
> 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
> Always - 0
> 7 Seek_Error_Rate 0x000f 060 060 030 Pre-fail
> Always - 1108085
> 9 Power_On_Hours 0x0032 100 100 000 Old_age
> Always - 717
> 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
> Always - 0
> 12 Power_Cycle_Count 0x0032 100 100 020 Old_age
> Always - 74
> 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age
> Always - 0
> 184 End-to-End_Error 0x0032 100 100 099 Old_age
> Always - 0
> 187 Reported_Uncorrect 0x0032 001 001 000 Old_age
> Always - 792
> 188 Command_Timeout 0x0032 100 100 000 Old_age
> Always - 0
> 189 High_Fly_Writes 0x003a 100 100 000 Old_age
> Always - 0
> 190 Airflow_Temperature_Cel 0x0022 065 062 045 Old_age
> Always - 35 (Min/Max 35/35)
> 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
> Always - 0
> 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
> Always - 202
> 193 Load_Cycle_Count 0x0032 100 100 000 Old_age
> Always - 265
> 194 Temperature_Celsius 0x0022 035 040 000 Old_age
> Always - 35 (0 19 0 0)
> 195 Hardware_ECC_Recovered 0x001a 015 009 000 Old_age
> Always - 2447656
> 197 Current_Pending_Sector 0x0012 096 096 000 Old_age
> Always - 368
> 198 Offline_Uncorrectable 0x0010 096 096 000 Old_age
> Offline - 368
> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
> Always - 0
> 240 Head_Flying_Hours 0x0000 100 253 000 Old_age
> Offline - 9354438771404
> 241 Total_LBAs_Written 0x0000 100 253 000 Old_age
> Offline - 793142133
> 242 Total_LBAs_Read 0x0000 100 253 000 Old_age
> Offline - 307847059
>
> SMART Error Log Version: 1
> ATA Error Count: 828 (device log contains only the most recent five
> errors) CR = Command Register [HEX]
> FR = Features Register [HEX]
> SC = Sector Count Register [HEX]
> SN = Sector Number Register [HEX]
> CL = Cylinder Low Register [HEX]
> CH = Cylinder High Register [HEX]
> DH = Device/Head Register [HEX]
> DC = Device Command Register [HEX]
> ER = Error register [HEX]
> ST = Status register [HEX]
> Powered_Up_Time is measured from power on, and printed as
> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
> SS=sec, and sss=millisec. It "wraps" after 49.710 days.
>
> Error 828 occurred at disk power-on lifetime: 705 hours (29 days + 9
> hours) When the command that caused the error occurred, the device was
> active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 08 ff ff ff ef 00 03:44:18.432 READ DMA EXT
> 27 00 00 00 00 00 e0 00 03:44:18.431 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 03:44:18.423 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 03:44:18.391 SET FEATURES [Set transfer
> mode] 27 00 00 00 00 00 e0 00 03:44:18.391 READ NATIVE MAX
> ADDRESS EXT
>
> Error 827 occurred at disk power-on lifetime: 705 hours (29 days + 9
> hours) When the command that caused the error occurred, the device was
> active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 08 ff ff ff ef 00 03:44:15.060 READ DMA EXT
> 27 00 00 00 00 00 e0 00 03:44:15.059 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 03:44:15.051 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 03:44:15.019 SET FEATURES [Set transfer
> mode] 27 00 00 00 00 00 e0 00 03:44:15.019 READ NATIVE MAX
> ADDRESS EXT
>
> Error 826 occurred at disk power-on lifetime: 705 hours (29 days + 9
> hours) When the command that caused the error occurred, the device was
> active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 08 ff ff ff ef 00 03:44:11.687 READ DMA EXT
> 27 00 00 00 00 00 e0 00 03:44:11.686 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 03:44:11.662 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 03:44:11.566 SET FEATURES [Set transfer
> mode] 27 00 00 00 00 00 e0 00 03:44:11.566 READ NATIVE MAX
> ADDRESS EXT
>
> Error 825 occurred at disk power-on lifetime: 705 hours (29 days + 9
> hours) When the command that caused the error occurred, the device was
> active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 08 ff ff ff ef 00 03:44:08.323 READ DMA EXT
> 27 00 00 00 00 00 e0 00 03:44:08.322 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 03:44:08.314 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 03:44:08.282 SET FEATURES [Set transfer
> mode] 27 00 00 00 00 00 e0 00 03:44:08.282 READ NATIVE MAX
> ADDRESS EXT
>
> Error 824 occurred at disk power-on lifetime: 705 hours (29 days + 9
> hours) When the command that caused the error occurred, the device was
> active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 08 ff ff ff ef 00 03:44:04.950 READ DMA EXT
> 27 00 00 00 00 00 e0 00 03:44:04.949 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 03:44:04.941 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 03:44:04.910 SET FEATURES [Set transfer
> mode] 27 00 00 00 00 00 e0 00 03:44:04.909 READ NATIVE MAX
> ADDRESS EXT
>
> SMART Self-test log structure revision number 1
> No self-tests have been logged. [To run self-tests, use: smartctl -t]
>
>
> SMART Selective self-test log data structure revision number 1
> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> 1 0 0 Not_testing
> 2 0 0 Not_testing
> 3 0 0 Not_testing
> 4 0 0 Not_testing
> 5 0 0 Not_testing
> Selective self-test flags (0x0):
> After scanning selected spans, do NOT read-scan remainder of disk.
> If Selective self-test is pending on power-up, resume after 0 minute
> delay.
I might run the selftest (long) to get a better idea, but if there is not a
firmware update for this drive on the Seagate site, I believe I'd be asking
for an RA forthwith.
Be aware that I just updated 2 identical 1 terrabyte Seagate drives about 3
weeks ago, and the firmware update, while it did not scramble tha partition
table data, did scramble the partition labels AND the blkid's of the boot
drive only. The second drive no longer is hanging the system with bus
resets, but it still has a write speed of about 3.5 megs/second. I had to
re-install. Fortunately I had data backups from the night before courtesy
amanda.
--
Cheers, Gene
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
<http://tinyurl.com/ddg5bz>
<http://www.cantrip.org/gatto.html>
Row, row, row your bits, gently down the stream...
next prev parent reply other threads:[~2011-04-30 12:15 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-23 11:05 Seagate hard disk firmware issue BU66ER BAD6ER
2011-01-23 13:42 ` Alan Cox
2011-01-25 1:21 ` Robert Hancock
2011-01-25 6:06 ` BU66ER BAD6ER
2011-04-30 11:32 ` BU66ER BAD6ER
2011-04-30 12:08 ` gene heskett [this message]
2011-04-30 22:39 ` BU66ER BAD6ER
2011-05-01 17:18 ` gene heskett
2011-06-06 10:09 ` BU66ER BAD6ER
2011-06-06 10:36 ` gene heskett
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201104300808.59185.gheskett@wdtv.com \
--to=gheskett@wdtv.com \
--cc=debu66er@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.