[U-Boot] [PATCH v3 0/2] SMDKV310 Board Support

[U-Boot] [PATCH v3 0/2] SMDKV310 Board Support

[Chander Kashyap]

Hi,
This patchset adds support for a new board SMDKV310, based on S5PV310 SOC.
This SOC is very similar to S5PC210 SOC, hence we are re-using this SOC code.

Specific changes in PATCH v3 are mention in specific patch files.

Chander Kashyap (2):
  ARMV7: Add support for Samsung SMDKV310 Board
  ARMV7: MMC SPL Boot support for SMDKV310 board

 MAINTAINERS                                        |    4 +
 Makefile                                           |   11 +
 board/samsung/smdkv310/Makefile                    |   46 ++
 board/samsung/smdkv310/lowlevel_init.S             |  470 ++++++++++++++++++++
 board/samsung/smdkv310/mem_setup.S                 |  365 +++++++++++++++
 board/samsung/smdkv310/smdkv310.c                  |  136 ++++++
 boards.cfg                                         |    1 +
 include/configs/smdkv310.h                         |  169 +++++++
 mmc_spl/board/samsung/smdkv310/Makefile            |  105 +++++
 mmc_spl/board/samsung/smdkv310/mmc_boot.c          |   81 ++++
 .../board/samsung/smdkv310/tools/mkv310_image.c    |  116 +++++
 mmc_spl/board/samsung/smdkv310/u-boot.lds          |   86 ++++
 12 files changed, 1590 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/smdkv310/Makefile
 create mode 100644 board/samsung/smdkv310/lowlevel_init.S
 create mode 100644 board/samsung/smdkv310/mem_setup.S
 create mode 100644 board/samsung/smdkv310/smdkv310.c
 create mode 100644 include/configs/smdkv310.h
 create mode 100644 mmc_spl/board/samsung/smdkv310/Makefile
 create mode 100644 mmc_spl/board/samsung/smdkv310/mmc_boot.c
 create mode 100644 mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c
 create mode 100644 mmc_spl/board/samsung/smdkv310/u-boot.lds

--
1.7.4.1

[U-Boot] [PATCH v3 1/2] ARMV7: Add support for Samsung SMDKV310 Board

[Chander Kashyap]

SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
Changes for v2:
	- Coding Style Cleanup
	- Removed unwanted macros from board config file.
	- Ethernet controllor configuration is done using gpio structures.
	- MMC Controllor gpio configuration corrected.
	- Added MAINTAINERS entry.
	- Removed unwanted code from mem_setup.S.
Changes for v3:
	- Comment style fixed
	- Added New macro in board config file.

 MAINTAINERS                            |    4 +
 board/samsung/smdkv310/Makefile        |   46 +++
 board/samsung/smdkv310/lowlevel_init.S |  470 ++++++++++++++++++++++++++++++++
 board/samsung/smdkv310/mem_setup.S     |  365 +++++++++++++++++++++++++
 board/samsung/smdkv310/smdkv310.c      |  136 +++++++++
 boards.cfg                             |    1 +
 include/configs/smdkv310.h             |  169 ++++++++++++
 7 files changed, 1191 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/smdkv310/Makefile
 create mode 100644 board/samsung/smdkv310/lowlevel_init.S
 create mode 100644 board/samsung/smdkv310/mem_setup.S
 create mode 100644 board/samsung/smdkv310/smdkv310.c
 create mode 100644 include/configs/smdkv310.h

diff --git a/MAINTAINERS b/MAINTAINERS
index e2c48a8..a3f6ef2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -702,6 +702,10 @@ Minkyu Kang <mk7.kang@samsung.com>
 	s5p_goni		ARM ARMV7 (S5PC110 SoC)
 	s5pc210_universal	ARM ARMV7 (S5PC210 SoC)

+Chander Kashyap <k.chander@samsung.com>
+
+	SMDKV310		ARM ARMV7 (S5PC210 SoC)
+
 Frederik Kriewitz <frederik@kriewitz.eu>

 	devkit8000	ARM ARMV7 (OMAP3530 SoC)
diff --git a/board/samsung/smdkv310/Makefile b/board/samsung/smdkv310/Makefile
new file mode 100644
index 0000000..8e9b703
--- /dev/null
+++ b/board/samsung/smdkv310/Makefile
@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2011 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+SOBJS	:= mem_setup.o
+SOBJS	+= lowlevel_init.o
+COBJS	+= smdkv310.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+all:	 $(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/smdkv310/lowlevel_init.S b/board/samsung/smdkv310/lowlevel_init.S
new file mode 100644
index 0000000..359cff4
--- /dev/null
+++ b/board/samsung/smdkv310/lowlevel_init.S
@@ -0,0 +1,470 @@
+/*
+ * Lowlevel setup for SMDKV310 board based on S5PC210
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+/*
+ * Register usages:
+ *
+ * r5 has zero always
+ * r7 has GPIO part1 base 0x11400000
+ * r6 has GPIO part2 base 0x11000000
+ */
+
+#define MEM_DLLl_ON
+
+_TEXT_BASE:
+	.word	CONFIG_SYS_TEXT_BASE
+
+	.globl lowlevel_init
+lowlevel_init:
+	push	{lr}
+
+	/* r5 has always zero */
+	mov	r5, #0
+	ldr	r7, =S5PC210_GPIO_PART1_BASE
+	ldr	r6, =S5PC210_GPIO_PART2_BASE
+
+	/* check reset status  */
+	ldr     r0, =(S5PC210_POWER_BASE + 0x81C)	@ INFORM7
+        ldr     r1, [r0]
+
+	/* AFTR wakeup reset */
+	ldr	r2, =S5P_CHECK_DIDLE
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* Sleep wakeup reset */
+	ldr	r2, =S5P_CHECK_SLEEP
+	cmp	r1, r2
+	beq	wakeup_reset
+
+	/*
+	 * If U-boot is already running in ram, no need to relocate U-Boot.
+	 * Memory controller must be configured before relocating U-Boot
+	 * in ram.
+	 */
+	ldr	r0, =0x00ffffff		/* r0 <- Mask Bits*/
+	bic	r1, pc, r0		/* pc <- current addr of code */
+					/* r1 <- unmasked bits of pc */
+
+	ldr	r2, _TEXT_BASE		/* r2 <- original base addr in ram */
+	bic	r2, r2, r0		/* r2 <- unmasked bits of r2*/
+	cmp     r1, r2                  /* compare r1, r2 */
+	beq     1f			/* r0 == r1 then skip sdram init */
+
+	/* init system clock */
+	bl system_clock_init
+
+	/* Memory initialize */
+	bl mem_ctrl_asm_init
+
+1:
+	/* for UART */
+	bl uart_asm_init
+	bl tzpc_init
+	pop	{pc}
+
+wakeup_reset:
+	bl system_clock_init
+	bl mem_ctrl_asm_init
+	bl tzpc_init
+
+exit_wakeup:
+	/* Load return address and jump to kernel */
+	ldr     r0, =(S5PC210_POWER_BASE + 0x800)	@ INFORM0
+
+	/* r1 = physical address of s5pc210_cpu_resume function */
+	ldr	r1, [r0]
+
+	/* Jump to kernel*/
+	mov	pc, r1
+	nop
+	nop
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+system_clock_init:
+	push	{lr}
+	ldr	r0, =S5PC210_CLOCK_BASE
+
+	/* APLL(1), MPLL(1), CORE(0), HPM(0) */
+	ldr	r1, =0x0101
+	ldr	r2, =0x14200			@CLK_SRC_CPU
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x10000
+2:	subs	r1, r1, #1
+	bne	2b
+
+	ldr	r1, =0x00
+	ldr	r2, =0x0C210			@CLK_SRC_TOP0
+	str	r1, [r0, r2]
+
+	ldr	r1, =0x00
+	ldr	r2, =0x0C214			@CLK_SRC_TOP1_OFFSET
+	str	r1, [r0, r2]
+
+	/* DMC */
+	ldr	r1, =0x00
+	ldr	r2, =0x10200			@CLK_SRC_DMC_OFFSET
+	str	r1, [r0, r2]
+
+	/*CLK_SRC_LEFTBUS */
+	ldr	r1, =0x00
+	ldr	r2, =0x04200			@CLK_SRC_LEFTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/*CLK_SRC_RIGHTBUS */
+	ldr	r1, =0x00
+	ldr	r2, =0x08200			@CLK_SRC_RIGHTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/* SATA: SCLKMPLL(0), MMC[0:4]: SCLKMPLL(6) */
+	ldr	r1, =0x066666
+	ldr	r2, =0x0C240			@ CLK_SRC_FSYS
+	str	r1, [r0, r2]
+
+	/* UART[0:4], PWM: SCLKMPLL(6) */
+	ldr	r1, =0x06666666
+	ldr	r2, =0x0C250			@CLK_SRC_PERIL0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x10000
+3:	subs	r1, r1, #1
+	bne	3b
+
+	/*
+	 * CLK_DIV_CPU0:
+	 *
+	 * PCLK_DBG_RATIO[20]	0x1
+	 * ATB_RATIO[16]	0x3
+	 * PERIPH_RATIO[12]	0x3
+	 * COREM1_RATIO[8]	0x7
+	 * COREM0_RATIO[4]	0x3
+	 */
+	ldr	r1, =0x01133730
+	ldr	r2, =0x14500			@CLK_DIV_CPU0_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_CPU1: COPY_RATIO [0]	0x3 */
+	ldr	r1, =0x03
+	ldr	r2, =0x14504			@CLK_DIV_CPU1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * CLK_DIV_DMC0:
+	 *
+	 * CORE_TIMERS_RATIO[28]	0x1
+	 * COPY2_RATIO[24]	0x3
+	 * DMCP_RATIO[20]	0x1
+	 * DMCD_RATIO[16]	0x1
+	 * DMC_RATIO[12]	0x1
+	 * DPHY_RATIO[8]	0x1
+	 * ACP_PCLK_RATIO[4]	0x1
+	 * ACP_RATIO[0]		0x3
+	 */
+	ldr	r1, =0x13111113
+	ldr	r2, =0x010500			@CLK_DIV_DMC0_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * CLK_DIV_DMC1:
+	 *
+	 * DPM_RATIO[24]	0x1
+	 * DVSEM_RATIO[16]	0x1
+	 * PWI_RATIO[8]		0x1
+	 */
+	ldr	r1, =0x01010100
+	ldr	r2, =0x010504			@CLK_DIV_DMC1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * CLK_DIV_LEFRBUS:
+	 *
+	 * GPL_RATIO[4]		0x1
+	 * GDL_RATIO[0]		0x3
+	 */
+	ldr	r1, =0x013
+	ldr	r2, =0x04500			@CLK_DIV_LEFTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * CLK_DIV_RIGHTBUS:
+	 *
+	 * GPR_RATIO[4]		0x1
+	 * GDR_RATIO[0]		0x3
+	 */
+	ldr	r1, =0x013
+	ldr	r2, =0x08500			@CLK_DIV_RIGHTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * CLK_DIV_TOP:
+	 *
+	 * ONENAND_RATIO[16]	0x0
+	 * ACLK_133_RATIO[12]	0x5
+	 * ACLK_160_RATIO[8]	0x4
+	 * ACLK_100_RATIO[4]	0x7
+	 * ACLK_200_RATIO[0]	0x3
+	 */
+	ldr	r1, =0x05473
+	ldr	r2, =0x0C510			@CLK_DIV_TOP_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[0:1] */
+	ldr	r1, =0x000f000f			/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =0x0C544			@ CLK_DIV_FSYS1
+	str	r1, [r0, r2]
+
+	/* MMC[2:3] */
+	ldr	r1, =0x000f020f			/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =0x0C548			@ CLK_DIV_FSYS2
+	str	r1, [r0, r2]
+
+	/* MMC4 */
+	ldr	r1, =0x000f			/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =0x0C54C			@ CLK_DIV_FSYS3
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x10000
+4:	subs	r1, r1, #1
+	bne	4b
+
+	/*
+	 * CLK_DIV_PERIL0:
+	 *
+	 * UART5_RATIO[20]	8
+	 * UART4_RATIO[16]	8
+	 * UART3_RATIO[12]	8
+	 * UART2_RATIO[8]	8
+	 * UART1_RATIO[4]	8
+	 * UART0_RATIO[0]	8
+	 */
+	ldr	r1, =0x774777
+	ldr	r2, =0x0C550			@CLK_DIV_PERIL0_OFFSET
+	str	r1, [r0, r2]
+
+	/* SLIMBUS: ???, PWM */
+	ldr	r1, =0x8
+	ldr	r2, =0x0C55C			@ CLK_DIV_PERIL3
+	str	r1, [r0, r2]
+
+	/* Set PLL locktime */
+	ldr	r1, =0x01C20
+	ldr	r2, =0x014000			@APLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =0x01C20
+	ldr	r2, =0x014008			@MPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =0x01C20
+	ldr	r2, =0x0C010			@EPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+	ldr	r1, =0x01C20
+	ldr	r2, =0x0C020			@VPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * APLL_CON1:
+	 *
+	 * APLL_AFC_ENB[31]	0x1
+	 * APLL_AFC[0]		0xC
+	 */
+	ldr	r1, =0x8000000C
+	ldr	r2, =0x014104			@APLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * APLL_CON0:
+	 *
+	 * APLL_MDIV[16]	0xFA
+	 * APLL_PDIV[8]		0x6
+	 * APLL_SDIV[0]		0x1
+	 */
+	ldr	r1, =0x80FA0601
+	ldr	r2, =0x014100			@APLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * MPLL_CON1:
+	 *
+	 * MPLL_AFC_ENB[31]	0x1
+	 * MPLL_AFC[0]		0x1C
+	 */
+	ldr	r1, =0x0000001C
+	ldr	r2, =0x01410C			@MPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * MPLL_CON0:
+	 *
+	 * MPLL_MDIV[16]	0xC8
+	 * MPLL_PDIV[8]		0x6
+	 * MPLL_SDIV[0]		0x1
+	 */
+	ldr	r1, =0x80C80601
+	ldr	r2, =0x014108			@MPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* EPLL */
+	ldr	r1, =0x0
+	ldr	r2, =0x0C114			@EPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * EPLL_CON0:
+	 *
+	 * EPLL_MDIV[16]	0x30
+	 * EPLL_PDIV[8]		0x3
+	 * EPLL_SDIV[0]		0x2
+	 */
+	ldr	r1, =0x80300302
+	ldr	r2, =0x0C110			@EPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * VPLL_CON1:
+	 *
+	 * VPLL_MRR[24]		0x11
+	 * VPLL_MFR[16]		0x0
+	 * VPLL_K[0]		0x400
+	 */
+	ldr	r1, =0x11000400
+	ldr	r2, =0x0C124			@VPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/*
+	 * VPLL_CON0:
+	 *
+	 * VPLL_MDIV[16]	0x35
+	 * VPLL_PDIV[8]		0x3
+	 * VPLL_SDIV[0]		0x2
+	 */
+	ldr	r1, =0x80350302
+	ldr	r2, =0x0C120			@VPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+3:	subs	r1, r1, #1
+	bne	3b
+
+	pop	{pc}
+/*
+ * uart_asm_init: Initialize UART in asm mode, 115200bps fixed.
+ * void uart_asm_init(void)
+ */
+	.globl uart_asm_init
+uart_asm_init:
+
+	/* setup UART0-UART3 GPIOs (part1) */
+	mov	r0, r7
+	ldr	r1, =0x22222222
+	str	r1, [r0, #0x00]			@ S5PC210_GPIO_A0_OFFSET
+	ldr	r1, =0x00222222
+	str	r1, [r0, #0x20]			@ S5PC210_GPIO_A1_OFFSET
+
+	ldr r0, =S5PC210_UART_BASE
+	add r0, r0, #S5PC210_DEFAULT_UART_OFFSET
+
+	ldr r1, =0x3C5
+	str	r1, [r0, #0x4]
+	ldr r1, =0x111
+	str	r1, [r0, #0x8]
+	ldr r1, =0x3
+	str	r1, [r0, #0x0]
+	ldr r1, =0x35
+	str	r1, [r0, #0x28]
+	ldr r1, =0x4
+	str	r1, [r0, #0x2c]
+
+	mov	pc, lr
+	nop
+	nop
+	nop
+
+/* Setting TZPC[TrustZone Protection Controller] */
+tzpc_init:
+	ldr	r0, =0x10110000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	ldr	r0, =0x10120000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	ldr	r0, =0x10130000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	ldr	r0, =0x10140000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	ldr	r0, =0x10150000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	ldr	r0, =0x10160000
+	mov	r1, #0x0
+	str	r1, [r0]
+	mov	r1, #0xff
+	str	r1, [r0, #0x0804]
+	str	r1, [r0, #0x0810]
+	str	r1, [r0, #0x081C]
+	str	r1, [r0, #0x0828]
+
+	mov	pc, lr
diff --git a/board/samsung/smdkv310/mem_setup.S b/board/samsung/smdkv310/mem_setup.S
new file mode 100644
index 0000000..d8c3ed4
--- /dev/null
+++ b/board/samsung/smdkv310/mem_setup.S
@@ -0,0 +1,365 @@
+/*
+ * Memory setup for SMDKV310 board based on S5PC210
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+#define SET_MIU
+
+#define MEM_DLL
+
+#ifdef CONFIG_CLK_800_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_200_200
+#define DRAM_CLK_200
+#endif
+#ifdef CONFIG_CLK_1000_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_400_200
+#define DRAM_CLK_400
+#endif
+
+	.globl mem_ctrl_asm_init
+mem_ctrl_asm_init:
+
+	/*
+	* Async bridge configuration at CPU_core:
+	* 1: half_sync
+	* 0: full_sync
+	*/
+	ldr r0, =0x10010350
+	mov r1, #1
+	str r1, [r0]
+
+#ifdef SET_MIU
+	ldr	r0, =S5PC210_MIU_BASE	@0x10600000
+#ifdef CONFIG_MIU_1BIT_INTERLEAVED
+	ldr	r1, =0x0000000c
+	str	r1, [r0, #0x400]	@MIU_INTLV_CONFIG
+	ldr	r1, =0x40000000
+	str	r1, [r0, #0x808]	@MIU_INTLV_START_ADDR
+	ldr	r1, =0xbfffffff
+	str	r1, [r0, #0x810]	@MIU_INTLV_END_ADDR
+	ldr	r1, =0x00000001
+	str	r1, [r0, #0x800]	@MIU_MAPPING_UPDATE
+#endif
+#ifdef CONFIG_MIU_2BIT_INTERLEAVED
+	ldr	r1, =0x2000150c
+	str	r1, [r0, #0x400]	@MIU_INTLV_CONFIG
+	ldr	r1, =0x40000000
+	str	r1, [r0, #0x808]	@MIU_INTLV_START_ADDR
+	ldr	r1, =0xbfffffff
+	str	r1, [r0, #0x810]	@MIU_INTLV_END_ADDR
+	ldr	r1, =0x00000001
+	str	r1, [r0, #0x800]	@MIU_MAPPING_UPDATE
+#endif
+#ifdef CONFIG_MIU_LINEAR
+	ldr	r1, =0x40000000
+	str	r1, [r0, #0x818]	@MIU_SINGLE_MAPPING0_START_ADDR
+	ldr	r1, =0x7fffffff
+	str	r1, [r0, #0x820]	@MIU_SINGLE_MAPPING0_END_ADDR
+	ldr	r1, =0x80000000
+	str	r1, [r0, #0x828]	@MIU_SINGLE_MAPPING1_START_ADDR
+	ldr	r1, =0xbfffffff
+	str	r1, [r0, #0x830]	@MIU_SINGLE_MAPPING1_END_ADDR]
+	ldr	r1, =0x00000006
+	str	r1, [r0, #0x800]	@MIU_MAPPING_UPDATE
+#endif
+#endif
+	/* DREX0 */
+	ldr	r0, =S5PC210_DMC0_BASE	@0x10400000
+
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	ldr	r1, =0xE3855703
+	str	r1, [r0, #0x44]		@DMC_PHYZQCONTROL
+
+	mov	r2, #0x100000
+1:	subs	r2, r2, #1
+	bne	1b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	ldr	r1, =0x71101008
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+	ldr	r1, =0x7110100A
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0x7110100B
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+
+	ldr	r1, =0x00000000
+	str	r1, [r0, #0x20]		@DMC_PHYCONTROL2
+
+	ldr	r1, =0x0FFF301a
+	str	r1, [r0, #0x00]		@DMC_CONCONTROL
+	ldr	r1, =0x00312640
+	str	r1, [r0, #0x04]		@DMC_MEMCONTROL]
+
+#ifdef MIU_LINEAR
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #0x08]		@DMC_MEMCONFIG0
+	ldr	r1, =0x60e01323
+	str	r1, [r0, #0x0C]		@DMC_MEMCONFIG1
+#else	/* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */
+	ldr	r1, =0x20e01323
+	str	r1, [r0, #0x08]		@DMC_MEMCONFIG0
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #0x0C]		@DMC_MEMCONFIG1
+#endif
+
+	ldr	r1, =0xff000000
+	str	r1, [r0, #0x14]		@DMC_PRECHCONFIG
+
+	ldr	r1, =0x000000BC
+	str	r1, [r0, #0x30]		@DMC_TIMINGAREF
+
+#ifdef DRAM_CLK_330
+	ldr	r1, =0x3545548d
+	str	r1, [r0, #0x34]		@DMC_TIMINGROW
+	ldr	r1, =0x45430506
+	str	r1, [r0, #0x38]		@DMC_TIMINGDATA
+	ldr	r1, =0x4439033c
+	str	r1, [r0, #0x3C]		@DMC_TIMINGPOWER
+#endif
+#ifdef DRAM_CLK_400
+	ldr	r1, =0x4046654f
+	str	r1, [r0, #0x34]		@DMC_TIMINGROW
+	ldr	r1, =0x56500506
+	str	r1, [r0, #0x38]		@DMC_TIMINGDATA
+	ldr	r1, =0x5444033d
+	str	r1, [r0, #0x3C]		@DMC_TIMINGPOWER
+#endif
+	ldr	r1, =0x07000000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+2:	subs	r2, r2, #1
+	bne	2b
+
+	ldr	r1, =0x00020000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00030000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00010002
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00000328
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+3:	subs	r2, r2, #1
+	bne	3b
+
+	ldr	r1, =0x0a000000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+4:	subs	r2, r2, #1
+	bne	4b
+
+	ldr	r1, =0x07100000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+5:	subs	r2, r2, #1
+	bne	5b
+
+	ldr	r1, =0x00120000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00130000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00110002
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00100328
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+6:	subs	r2, r2, #1
+	bne	6b
+
+	ldr	r1, =0x0a100000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+7:	subs	r2, r2, #1
+	bne	7b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	mov	r2, #0x100000
+8:	subs	r2, r2, #1
+	bne	8b
+
+	/* DREX1 */
+	ldr	r0, =S5PC210_DMC1_BASE	@0x10410000
+
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	ldr	r1, =0xE3855703
+	str	r1, [r0, #0x44]		@DMC_PHYZQCONTROL
+
+	mov	r2, #0x100000
+1:	subs	r2, r2, #1
+	bne	1b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	ldr	r1, =0x71101008
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+	ldr	r1, =0x7110100A
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0x7110100B
+	str	r1, [r0, #0x18]		@DMC_PHYCONTROL0
+
+	ldr	r1, =0x00000000
+	str	r1, [r0, #0x20]		@DMC_PHYCONTROL2
+
+	ldr	r1, =0x0FFF301a
+	str	r1, [r0, #0x00]		@DMC_CONCONTROL
+	ldr	r1, =0x00312640
+	str	r1, [r0, #0x04]		@DMC_MEMCONTROL]
+
+#ifdef MIU_LINEAR
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #0x08]		@DMC_MEMCONFIG0
+	ldr	r1, =0x60e01323
+	str	r1, [r0, #0x0C]		@DMC_MEMCONFIG1
+#else	/* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */
+	ldr	r1, =0x20e01323
+	str	r1, [r0, #0x08]		@DMC_MEMCONFIG0
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #0x0C]		@DMC_MEMCONFIG1
+#endif
+
+	ldr	r1, =0xff000000
+	str	r1, [r0, #0x14]		@DMC_PRECHCONFIG
+
+	ldr	r1, =0x000000BC
+	str	r1, [r0, #0x30]		@DMC_TIMINGAREF
+
+#ifdef DRAM_CLK_330
+	ldr	r1, =0x3545548d
+	str	r1, [r0, #0x34]		@DMC_TIMINGROW
+	ldr	r1, =0x45430506
+	str	r1, [r0, #0x38]		@DMC_TIMINGDATA
+	ldr	r1, =0x4439033c
+	str	r1, [r0, #0x3C]		@DMC_TIMINGPOWER
+#endif
+#ifdef DRAM_CLK_400
+	ldr	r1, =0x4046654f
+	str	r1, [r0, #0x34]		@DMC_TIMINGROW
+	ldr	r1, =0x56500506
+	str	r1, [r0, #0x38]		@DMC_TIMINGDATA
+	ldr	r1, =0x5444033d
+	str	r1, [r0, #0x3C]		@DMC_TIMINGPOWER
+#endif
+
+	ldr	r1, =0x07000000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+2:	subs	r2, r2, #1
+	bne	2b
+
+	ldr	r1, =0x00020000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00030000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00010002
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00000328
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+3:	subs	r2, r2, #1
+	bne	3b
+
+	ldr	r1, =0x0a000000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+4:	subs	r2, r2, #1
+	bne	4b
+
+	ldr	r1, =0x07100000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+5:	subs	r2, r2, #1
+	bne	5b
+
+	ldr	r1, =0x00120000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00130000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00110002
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+	ldr	r1, =0x00100328
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+6:	subs	r2, r2, #1
+	bne	6b
+
+	ldr	r1, =0x0a100000
+	str	r1, [r0, #0x10]		@DMC_DIRECTCMD
+
+	mov	r2, #0x100000
+7:	subs	r2, r2, #1
+	bne	7b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #0x1C]		@DMC_PHYCONTROL1
+
+	mov	r2, #0x100000
+8:	subs	r2, r2, #1
+	bne	8b
+
+	/* turn on DREX0, DREX1 */
+	ldr	r0, =0x10400000		@APB_DMC_0_BASE
+	ldr	r1, =0x0FFF303a
+	str	r1, [r0, #0x00]		@DMC_CONCONTROL
+
+	ldr	r0, =0x10410000		@APB_DMC_1_BASE
+	ldr	r1, =0x0FFF303a
+	str	r1, [r0, #0x00]		@DMC_CONCONTROL
+
+	mov	pc, lr
diff --git a/board/samsung/smdkv310/smdkv310.c b/board/samsung/smdkv310/smdkv310.c
new file mode 100644
index 0000000..acf9ee7
--- /dev/null
+++ b/board/samsung/smdkv310/smdkv310.c
@@ -0,0 +1,136 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/sromc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+struct s5pc210_gpio_part1 *gpio1;
+struct s5pc210_gpio_part2 *gpio2;
+
+static void smc9115_pre_init(void)
+{
+	u32 smc_bw_conf, smc_bc_conf;
+
+	/* gpio configuration GPK0CON */
+	gpio_cfg_pin(&gpio2->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2));
+
+	/* Ethernet needs bus width of 16 bits */
+	smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK);
+	smc_bc_conf = SROMC_BC_TACS(0x0F) | SROMC_BC_TCOS(0x0F)
+			| SROMC_BC_TACC(0x0F) | SROMC_BC_TCOH(0x0F)
+			| SROMC_BC_TAH(0x0F)  | SROMC_BC_TACP(0x0F)
+			| SROMC_BC_PMC(0x0F);
+
+	/* Select and configure the SROMC bank */
+	s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf);
+}
+
+int board_init(void)
+{
+	gpio1 = (struct s5pc210_gpio_part1 *) S5PC210_GPIO_PART1_BASE;
+	gpio2 = (struct s5pc210_gpio_part2 *) S5PC210_GPIO_PART2_BASE;
+
+	smc9115_pre_init();
+
+	gd->bd->bi_arch_number = MACH_TYPE_SMDKV310;
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size	= get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE);
+
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC911X
+	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+	return rc;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	printf("\nBoard: SMDKV310\n");
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int i, err;
+
+	/*
+	 * MMC2 SD card GPIO:
+	 *
+	 * GPK2[0]	SD_2_CLK(2)
+	 * GPK2[1]	SD_2_CMD(2)
+	 * GPK2[2]	SD_2_CDn
+	 * GPK2[3:6]	SD_2_DATA[0:3](2)
+	 */
+	for (i = 0; i < 7; i++) {
+		/* GPK2[0:6] special function 2 */
+		gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2));
+
+		/* GPK2[0:6] drv 4x */
+		gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X);
+
+		/* GPK2[0:1] pull disable */
+		if (i == 0 || i == 1) {
+			gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE);
+			continue;
+		}
+
+		/* GPK2[2:6] pull up */
+		gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP);
+	}
+	err = s5p_mmc_init(2, 4);
+	return err;
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 4f48d19..f8a1cf9 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -146,6 +146,7 @@ omap4_sdp4430                arm         armv7       sdp4430             ti
 s5p_goni                     arm         armv7       goni                samsung        s5pc1xx
 smdkc100                     arm         armv7       smdkc100            samsung        s5pc1xx
 s5pc210_universal            arm         armv7       universal_c210      samsung        s5pc2xx
+smdkv310		     arm	 armv7	     smdkv310		 samsung	s5pc2xx
 harmony                      arm         armv7       harmony             nvidia         tegra2
 seaboard                     arm         armv7       seaboard            nvidia         tegra2
 actux1                       arm         ixp
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h
new file mode 100644
index 0000000..e0e1a03
--- /dev/null
+++ b/include/configs/smdkv310.h
@@ -0,0 +1,169 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG SMDKV310 (S5PC210) board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_ARMV7			1	/*This is an ARM V7 CPU core */
+#define CONFIG_SAMSUNG			1	/* in a SAMSUNG core */
+#define CONFIG_S5P			1	/* S5P Family */
+#define CONFIG_S5PC210			1	/* which is in a S5PC210 SoC */
+#define CONFIG_SMDKV310			1	/* working with SMDKV310*/
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_L2_OFF			1
+
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+#define CONFIG_SYS_TEXT_BASE		0x43E00000
+
+/* input clock of PLL: SMDKV310 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* Handling Sleep Mode*/
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (1 << 20))
+
+/* select serial console configuration */
+#define CONFIG_SERIAL_MULTI		1
+#define CONFIG_SERIAL1			1	/* use SERIAL 1 */
+#define CONFIG_BAUDRATE			115200
+#define S5PC210_DEFAULT_UART_OFFSET	0x010000
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC		1
+#define CONFIG_MMC			1
+#define CONFIG_S5P_MMC			1
+
+/* PWM */
+#define CONFIG_PWM			1
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_FAT
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_MMC_U_BOOT
+
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0 40007000 uImage; bootm 40007000"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"SMDKV310 # "
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size*/
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC2,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x6000000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ			1000
+
+/* valid baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/* Stack sizes */
+#define CONFIG_STACKSIZE		(256 << 10)	/* 256KB */
+
+/* SMDKV310 has 4 bank of DRAM */
+#define CONFIG_NR_DRAM_BANKS	4
+#define SDRAM_BANK_SIZE		(512UL << 20UL)	/* 512 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH		1
+#undef	CONFIG_CMD_IMLS
+#define CONFIG_IDENT_STRING		" for SMDKC210/V310"
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
+#endif
+
+#define CONFIG_CLK_1000_400_200
+
+/* MIU (Memory Interleaving Unit) */
+#define CONFIG_MIU_2BIT_INTERLEAVED
+
+#define CONFIG_ENV_IS_IN_MMC		1
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			(16 << 10)	/* 16 KB */
+#define RESERVE_BLOCK_SIZE		(512)
+#define BL1_SIZE			(16 << 10) /*16 K reserved for BL1*/
+#define CONFIG_ENV_OFFSET		(RESERVE_BLOCK_SIZE + BL1_SIZE)
+#define CONFIG_DOS_PARTITION		1
+
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define	COPY_BL2_SIZE			0x80000
+#define BL2_START_OFFSET		((CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)/512)
+#define BL2_SIZE_BLOC_COUNT		(COPY_BL2_SIZE/512)
+
+/* Ethernet Controllor Driver */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_BASE		0x5000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_ENV_SROM_BANK		1
+#endif /*CONFIG_CMD_NET*/
+#endif	/* __CONFIG_H */
--
1.7.4.1

[U-Boot] [PATCH v3 2/2] ARMV7: MMC SPL Boot support for SMDKV310 board

[Chander Kashyap]

Added MMC SPL boot support for SMDKV310. This framework design is
based on nand_spl support.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
---
Changes for v3:
	- spl file renamed to u-boot-mmc-spl.bin
	- spl directory renamed to mmc_spl
	- comments added in mkv310_image.c file

 Makefile                                           |   11 ++
 mmc_spl/board/samsung/smdkv310/Makefile            |  105 ++++++++++++++++++
 mmc_spl/board/samsung/smdkv310/mmc_boot.c          |   81 ++++++++++++++
 .../board/samsung/smdkv310/tools/mkv310_image.c    |  116 ++++++++++++++++++++
 mmc_spl/board/samsung/smdkv310/u-boot.lds          |   86 +++++++++++++++
 5 files changed, 399 insertions(+), 0 deletions(-)
 create mode 100644 mmc_spl/board/samsung/smdkv310/Makefile
 create mode 100644 mmc_spl/board/samsung/smdkv310/mmc_boot.c
 create mode 100644 mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c
 create mode 100644 mmc_spl/board/samsung/smdkv310/u-boot.lds

diff --git a/Makefile b/Makefile
index 384a59e..25b87b0 100644
--- a/Makefile
+++ b/Makefile
@@ -322,6 +322,10 @@ ALL += $(obj)u-boot-onenand.bin
 ONENAND_BIN ?= $(obj)onenand_ipl/onenand-ipl-2k.bin
 endif

+ifeq ($(CONFIG_MMC_U_BOOT),y)
+ALL += $(obj)mmc_spl/u-boot-mmc-spl.bin
+endif
+
 all:		$(ALL)

 $(obj)u-boot.hex:	$(obj)u-boot
@@ -413,6 +417,11 @@ onenand_ipl:	$(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk
 $(obj)u-boot-onenand.bin:	onenand_ipl $(obj)u-boot.bin
 		cat $(ONENAND_BIN) $(obj)u-boot.bin > $(obj)u-boot-onenand.bin

+mmc_spl:	$(TIMESTAMP_FILE) $(VERSION_FILE) depend
+		$(MAKE) -C mmc_spl/board/$(BOARDDIR) all
+
+$(obj)mmc_spl/u-boot-mmc-spl.bin:	mmc_spl
+
 $(VERSION_FILE):
 		@( localvers='$(shell $(TOPDIR)/tools/setlocalversion $(TOPDIR))' ; \
 		   printf '#define PLAIN_VERSION "%s%s"\n' \
@@ -1123,6 +1132,7 @@ clean:
 	@rm -f $(obj)lib/asm-offsets.s
 	@rm -f $(obj)nand_spl/{u-boot.lds,u-boot-spl,u-boot-spl.map,System.map}
 	@rm -f $(obj)onenand_ipl/onenand-{ipl,ipl.bin,ipl.map}
+	@rm -f $(obj)mmc_spl/{u-boot.lds,u-boot-spl,u-boot-spl.map,u-boot-spl.bin,u-boot-mmc-spl.bin}
 	@rm -f $(ONENAND_BIN)
 	@rm -f $(obj)onenand_ipl/u-boot.lds
 	@rm -f $(TIMESTAMP_FILE) $(VERSION_FILE)
@@ -1147,6 +1157,7 @@ clobber:	clean
 	@rm -fr $(obj)include/generated
 	@[ ! -d $(obj)nand_spl ] || find $(obj)nand_spl -name "*" -type l -print | xargs rm -f
 	@[ ! -d $(obj)onenand_ipl ] || find $(obj)onenand_ipl -name "*" -type l -print | xargs rm -f
+	@[ ! -d $(obj)mmc_spl ] || find $(obj)mmc_spl -name "*" -type l -print | xargs rm -f

 ifeq ($(OBJTREE),$(SRCTREE))
 mrproper \
diff --git a/mmc_spl/board/samsung/smdkv310/Makefile b/mmc_spl/board/samsung/smdkv310/Makefile
new file mode 100644
index 0000000..f1ce066
--- /dev/null
+++ b/mmc_spl/board/samsung/smdkv310/Makefile
@@ -0,0 +1,105 @@
+#
+# (C) Copyright 2006-2007
+# Stefan Roese, DENX Software Engineering, sr at denx.de.
+#
+# (C) Copyright 2008
+# Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
+#
+# (C) Copyright 2011
+# Chander Kashyap, Samsung Electronics, <k.chander@samsung.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+CONFIG_MMC_SPL	= y
+
+include $(TOPDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/mmc_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS	= -Bstatic -T $(mmcobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS	+= -DCONFIG_MMC_SPL
+CFLAGS	+= -DCONFIG_MMC_SPL
+CFLAGS	+= -DCONFIG_PRELOADER
+
+SOBJS	= start.o mem_setup.o lowlevel_init.o
+COBJS	= mmc_boot.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(OBJTREE)/mmc_spl/board/$(BOARDDIR)
+
+mmcobj	:= $(OBJTREE)/mmc_spl/
+
+
+MKV310_MMC_SPL_EXEC = mkv310_mmc_spl_exec
+MMC_SPL_BIN = u-boot-mmc-spl.bin
+
+ALL = $(mmcobj)u-boot-spl $(mmcobj)u-boot-spl.bin $(mmcobj)$(MMC_SPL_BIN)
+
+all:    $(obj).depend $(ALL)
+
+$(mmcobj)$(MMC_SPL_BIN):  $(mmcobj)u-boot-spl.bin tools/$(MKV310_MMC_SPL_EXEC)
+	./tools/$(MKV310_MMC_SPL_EXEC) $(mmcobj)u-boot-spl.bin $(mmcobj)$(MMC_SPL_BIN)
+	rm -f tools/$(MKV310_MMC_SPL_EXEC)
+
+tools/$(MKV310_MMC_SPL_EXEC): tools/mkv310_image.c
+	$(HOSTCC) tools/mkv310_image.c -o tools/$(MKV310_MMC_SPL_EXEC)
+
+$(mmcobj)u-boot-spl.bin:	$(mmcobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(mmcobj)u-boot-spl:	$(OBJS) $(mmcobj)u-boot.lds
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+		-Map $(mmcobj)u-boot-spl.map \
+		-o $(mmcobj)u-boot-spl
+
+$(mmcobj)u-boot.lds: $(LDSCRIPT)
+	$(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+# from cpu directory
+$(obj)start.S:
+	@rm -f $@
+	@ln -s $(TOPDIR)/arch/arm/cpu/armv7/start.S $@
+
+# from board directory
+$(obj)mem_setup.S:
+	@rm -f $@
+	@ln -s $(TOPDIR)/board/samsung/smdkv310/mem_setup.S $@
+
+$(obj)lowlevel_init.S:
+	@rm -f $@
+	@ln -s $(TOPDIR)/board/samsung/smdkv310/lowlevel_init.S $@
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/mmc_spl/board/samsung/smdkv310/mmc_boot.c b/mmc_spl/board/samsung/smdkv310/mmc_boot.c
new file mode 100644
index 0000000..b401350
--- /dev/null
+++ b/mmc_spl/board/samsung/smdkv310/mmc_boot.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include<common.h>
+#include<config.h>
+
+typedef u32(*copy_sd_mmc_to_mem) \
+	(u32 start_block, u32 block_count, u32 *dest_addr);
+
+
+void copy_uboot_to_ram(void)
+{
+	copy_sd_mmc_to_mem copy_bl2 = (copy_sd_mmc_to_mem)(0x00002488);
+	copy_bl2(BL2_START_OFFSET,\
+		BL2_SIZE_BLOC_COUNT, (u32 *)CONFIG_SYS_TEXT_BASE);
+}
+
+void board_init_f(unsigned long bootflag)
+{
+	__attribute__((noreturn)) void (*uboot)(void);
+	copy_uboot_to_ram();
+
+	/* Jump to U-Boot image */
+	uboot = (void *)CONFIG_SYS_TEXT_BASE;
+	(*uboot)();
+	/* Never returns Here */
+}
+
+/* Place Holders */
+void board_init_r(gd_t *id, ulong dest_addr)
+{
+}
+
+void do_undefined_instruction(struct pt_regs *pt_regs)
+{
+}
+
+void do_software_interrupt(struct pt_regs *pt_regs)
+{
+}
+
+void do_prefetch_abort(struct pt_regs *pt_regs)
+{
+}
+
+void do_data_abort(struct pt_regs *pt_regs)
+{
+}
+
+void do_not_used(struct pt_regs *pt_regs)
+{
+}
+
+void do_fiq(struct pt_regs *pt_regs)
+{
+}
+
+#ifndef CONFIG_USE_IRQ
+void do_irq(struct pt_regs *pt_regs)
+{
+}
+#endif
diff --git a/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c b/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c
new file mode 100644
index 0000000..b98f233
--- /dev/null
+++ b/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c
@@ -0,0 +1,116 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <fcntl.h>
+#include <errno.h>
+#include <string.h>
+
+#define CHECKSUM_OFFSET		(14*1024-4)
+#define BUFSIZE			(16*1024)
+#define FILE_PERM		(S_IRUSR | S_IWUSR | S_IRGRP \
+				| S_IWGRP | S_IROTH | S_IWOTH)
+/*
+* Requirement:
+* IROM code reads first 14K bytes from boot device.
+* It then calculates the checksum of 14K-4 bytes and compare with data at
+* 14K-4 offset.
+*
+* This function takes two filenames:
+* IN  "u-boot-spl.bin" and
+* OUT "u-boot-mmc-spl.bin" as filenames.
+* It reads the "u-boot-spl.bin" in 16K buffer.
+* It calculates checksum of 14K-4 Bytes and stores at 14K-4 offset in buffer.
+* It writes the buffer to "u-boot-mmc-spl.bin" file.
+*/
+
+int main(int argc, char **argv)
+{
+	int i, len;
+	unsigned char buffer[BUFSIZE] = {0};
+	int ifd, ofd;
+	unsigned int checksum = 0, count;
+
+	if (argc != 3) {
+		printf(" %d Wrong number of arguments\n", argc);
+		exit(EXIT_FAILURE);
+	}
+
+	ifd = open(argv[1], O_RDONLY);
+	if (ifd < 0) {
+		fprintf(stderr, "%s: Can't open %s: %s\n",
+			argv[0], argv[1], strerror(errno));
+		exit(EXIT_FAILURE);
+	}
+
+	ofd = open(argv[2], O_WRONLY | O_CREAT | O_TRUNC, FILE_PERM);
+	if (ifd < 0) {
+		fprintf(stderr, "%s: Can't open %s: %s\n",
+			argv[0], argv[2], strerror(errno));
+		if (ifd)
+			close(ifd);
+		exit(EXIT_FAILURE);
+	}
+
+	len = lseek(ifd, 0, SEEK_END);
+	lseek(ifd, 0, SEEK_SET);
+
+	count = (len < CHECKSUM_OFFSET) ? len : CHECKSUM_OFFSET;
+
+	if (read(ifd, buffer, count) != count) {
+		fprintf(stderr, "%s: Can't read %s: %s\n",
+			argv[0], argv[1], strerror(errno));
+
+		if (ifd)
+			close(ifd);
+		if (ofd)
+			close(ofd);
+
+		exit(EXIT_FAILURE);
+	}
+
+	for (i = 0, checksum = 0; i < CHECKSUM_OFFSET; i++)
+		checksum += buffer[i];
+
+	memcpy(&buffer[CHECKSUM_OFFSET], &checksum, sizeof(checksum));
+
+	if (write(ofd, buffer, BUFSIZE) != BUFSIZE) {
+		fprintf(stderr, "%s: Can't write %s: %s\n",
+			argv[0], argv[2], strerror(errno));
+
+		if (ifd)
+			close(ifd);
+		if (ofd)
+			close(ofd);
+
+		exit(EXIT_FAILURE);
+	}
+
+	if (ifd)
+		close(ifd);
+	if (ofd)
+		close(ofd);
+
+	return EXIT_SUCCESS;
+}
diff --git a/mmc_spl/board/samsung/smdkv310/u-boot.lds b/mmc_spl/board/samsung/smdkv310/u-boot.lds
new file mode 100644
index 0000000..61cd16a
--- /dev/null
+++ b/mmc_spl/board/samsung/smdkv310/u-boot.lds
@@ -0,0 +1,86 @@
+/*
+ * (C) Copyright 2011
+ * Chander Kashyap, Samsung Electronics, <k.chander@samsung.com>
+ *
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text	:
+	{
+		start.o	(.text)
+		*(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : {
+		*(.data)
+	}
+
+	. = ALIGN(4);
+
+	. = .;
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	_end = .;
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		__bss_end__ = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
+}
--
1.7.4.1

[U-Boot] [PATCH v3 0/2] SMDKV310 Board Support

[Wolfgang Denk]

Dear Chander Kashyap,

In message <1305796982-7155-1-git-send-email-chander.kashyap@linaro.org> you wrote:
>
> This patchset adds support for a new board SMDKV310, based on S5PV310 SOC.
> This SOC is very similar to S5PC210 SOC, hence we are re-using this SOC code.

Which patchset? I see only this cover letter, but neither patch 1/2
nor patch 2.2 ?

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Life is a game. Money is how we keep score.              - Ted Turner

[U-Boot] [Samsung] [PATCH v3 0/2] SMDKV310 Board Support

[Angus Ainslie]

Hi Wolfgang

On Thu, May 19, 2011 at 1:00 PM, Wolfgang Denk <wd@denx.de> wrote:
> Dear Chander Kashyap,
>
> In message <1305796982-7155-1-git-send-email-chander.kashyap@linaro.org> you wrote:
>>
>> This patchset adds support for a new board SMDKV310, based on S5PV310 SOC.
>> This SOC is very similar to S5PC210 SOC, hence we are re-using this SOC code.
>
> Which patchset? I see only this cover letter, but neither patch 1/2
> nor patch 2.2 ?
>

It looks like they ended up in a different thread.

http://lists.denx.de/pipermail/u-boot/2011-May/092977.html
http://lists.denx.de/pipermail/u-boot/2011-May/092976.html

Angus


-- 
Angus Ainslie <angus.ainslie@linaro.org>
Team Lead, Samsung Landing Team

[U-Boot] [Samsung] [PATCH v3 0/2] SMDKV310 Board Support

[Scott Bambrough]

On Thu, 2011-05-19 at 21:00 +0200, Wolfgang Denk wrote:
> Dear Chander Kashyap,
> 
> In message <1305796982-7155-1-git-send-email-chander.kashyap@linaro.org> you wrote:
> >
> > This patchset adds support for a new board SMDKV310, based on S5PV310 SOC.
> > This SOC is very similar to S5PC210 SOC, hence we are re-using this SOC code.
> 
> Which patchset? I see only this cover letter, but neither patch 1/2
> nor patch 2.2 ?

I see them all.

Cheers,

Scott

[U-Boot] [Samsung] [PATCH v3 0/2] SMDKV310 Board Support

[Wolfgang Denk]

Dear Angus Ainslie,

In message <BANLkTimAZGVhLRg7FDEH1mOkzwCo9fC1cg@mail.gmail.com> you wrote:
> 
> > Which patchset? I see only this cover letter, but neither patch 1/2
> > nor patch 2.2 ?
> 
> It looks like they ended up in a different thread.

I found them.  You also had the linaro-dev list on Cc:, and the
Linaro mail server was faster, so they got sorted into my Linaro
folder.

Sorry for the noise.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Insufficient facts always invite danger.
	-- Spock, "Space Seed", stardate 3141.9

[U-Boot] [PATCH v3 2/2] ARMV7: MMC SPL Boot support for SMDKV310 board

[Wolfgang Denk]

Dear Chander Kashyap,

In message <1305796982-7155-3-git-send-email-chander.kashyap@linaro.org> you wrote:
> Added MMC SPL boot support for SMDKV310. This framework design is
> based on nand_spl support.
> 
> Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>

Checkpatch says:

WARNING: line over 80 characters
#1333: FILE: include/configs/smdkv310.h:158:
+#define BL2_START_OFFSET               ((CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)/512)


Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"If you own a machine, you are in turn owned by it,  and  spend  your
time serving it..."    - Marion Zimmer Bradley, _The Forbidden Tower_