[PATCHv7 0/2] ARM: I2C: Add device tree bindings to i2c-mux-gpio

[PATCHv7 0/2] ARM: I2C: Add device tree bindings to i2c-mux-gpio

[Maxime Ripard]

Hi everyone,

This patchset adds the device tree entry to the CFA-10049 board of its i2c
muxer. This muxer controls sub-buses that contains three Nuvoton NAU7802
ADCs and a NXP PCA955 GPIO expander. Support for these will be added
eventually.

Thanks,
Maxime

Changes from v6:
  - Changed the return value when neither platform data nor dt was available
  - Fix a sentence in the documentation

Maxime Ripard (2):
  i2c: mux: Add dt support to i2c-mux-gpio driver
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

 .../devicetree/bindings/i2c/i2c-mux-gpio.txt       |   81 +++++++++++
 arch/arm/boot/dts/imx28-cfa10049.dts               |   24 ++++
 drivers/i2c/muxes/i2c-mux-gpio.c                   |  146 +++++++++++++++-----
 3 files changed, 220 insertions(+), 31 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt

-- 
1.7.9.5

[PATCHv7 0/2] ARM: I2C: Add device tree bindings to i2c-mux-gpio

[Maxime Ripard]

Hi everyone,

This patchset adds the device tree entry to the CFA-10049 board of its i2c
muxer. This muxer controls sub-buses that contains three Nuvoton NAU7802
ADCs and a NXP PCA955 GPIO expander. Support for these will be added
eventually.

Thanks,
Maxime

Changes from v6:
  - Changed the return value when neither platform data nor dt was available
  - Fix a sentence in the documentation

Maxime Ripard (2):
  i2c: mux: Add dt support to i2c-mux-gpio driver
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

 .../devicetree/bindings/i2c/i2c-mux-gpio.txt       |   81 +++++++++++
 arch/arm/boot/dts/imx28-cfa10049.dts               |   24 ++++
 drivers/i2c/muxes/i2c-mux-gpio.c                   |  146 +++++++++++++++-----
 3 files changed, 220 insertions(+), 31 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt

-- 
1.7.9.5

[PATCH 1/2] i2c: mux: Add dt support to i2c-mux-gpio driver

[Maxime Ripard]

Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.

Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Reviewed-by: Stephen Warren <swarren-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
Acked-by: Peter Korsgaard <peter.korsgaard-ob4gmnvZ1/cAvxtiuMwx3w@public.gmane.org>
---
 .../devicetree/bindings/i2c/i2c-mux-gpio.txt       |   81 +++++++++++
 drivers/i2c/muxes/i2c-mux-gpio.c                   |  146 +++++++++++++++-----
 2 files changed, 196 insertions(+), 31 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt

diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
new file mode 100644
index 0000000..66709a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
@@ -0,0 +1,81 @@
+GPIO-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+                                  +-----+  +-----+
+                                  | dev |  | dev |
+    +------------+                +-----+  +-----+
+    | SoC        |                   |        |
+    |            |          /--------+--------+
+    |   +------+ |  +------+    child bus A, on GPIO value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
+    |            |     |    \----------+--------+--------+
+    |   +------+ |     |               |        |        |
+    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
+    |   +------+ |                  | dev |  | dev |  | dev |
+    +------------+                  +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-gpio
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-gpios: list of gpios used to control the muxer
+* Standard I2C mux properties. See mux.txt in this directory.
+* I2C child bus nodes. See mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the revelant node's reg property will be output using the list of
+GPIOs, the first in the list holding the least-significant value.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+GPIOs will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled@3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
diff --git a/drivers/i2c/muxes/i2c-mux-gpio.c b/drivers/i2c/muxes/i2c-mux-gpio.c
index 566a675..e446f05 100644
--- a/drivers/i2c/muxes/i2c-mux-gpio.c
+++ b/drivers/i2c/muxes/i2c-mux-gpio.c
@@ -16,6 +16,8 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
+#include <linux/of_i2c.h>
+#include <linux/of_gpio.h>
 
 struct gpiomux {
 	struct i2c_adapter *parent;
@@ -57,29 +59,111 @@ static int __devinit match_gpio_chip_by_label(struct gpio_chip *chip,
 	return !strcmp(chip->label, data);
 }
 
+#ifdef CONFIG_OF
+static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *adapter_np, *child;
+	struct i2c_adapter *adapter;
+	unsigned *values, *gpios;
+	int i = 0;
+
+	if (!np)
+		return -ENODEV;
+
+	adapter_np = of_parse_phandle(np, "i2c-parent", 0);
+	if (!adapter_np) {
+		dev_err(&pdev->dev, "Cannot parse i2c-parent\n");
+		return -ENODEV;
+	}
+	adapter = of_find_i2c_adapter_by_node(adapter_np);
+	if (!adapter) {
+		dev_err(&pdev->dev, "Cannot find parent bus\n");
+		return -ENODEV;
+	}
+	mux->data.parent = i2c_adapter_id(adapter);
+	put_device(&adapter->dev);
+
+	mux->data.n_values = of_get_child_count(np);
+
+	values = devm_kzalloc(&pdev->dev,
+			      sizeof(*mux->data.values) * mux->data.n_values,
+			      GFP_KERNEL);
+	if (!values) {
+		dev_err(&pdev->dev, "Cannot allocate values array");
+		return -ENOMEM;
+	}
+
+	for_each_child_of_node(np, child) {
+		of_property_read_u32(child, "reg", values + i);
+		i++;
+	}
+	mux->data.values = values;
+
+	if (of_property_read_u32(np, "idle-state", &mux->data.idle))
+		mux->data.idle = I2C_MUX_GPIO_NO_IDLE;
+
+	mux->data.n_gpios = of_gpio_named_count(np, "mux-gpios");
+	if (mux->data.n_gpios < 0) {
+		dev_err(&pdev->dev, "Missing mux-gpios property in the DT.\n");
+		return -EINVAL;
+	}
+
+	gpios = devm_kzalloc(&pdev->dev,
+			     sizeof(*mux->data.gpios) * mux->data.n_gpios,
+                             GFP_KERNEL);
+	if (!gpios) {
+		dev_err(&pdev->dev, "Cannot allocate gpios array");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < mux->data.n_gpios; i++)
+		gpios[i] = of_get_named_gpio(np, "mux-gpios", i);
+
+	mux->data.gpios = gpios;
+
+	return 0;
+}
+#else
+static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
 static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 {
 	struct gpiomux *mux;
-	struct i2c_mux_gpio_platform_data *pdata;
 	struct i2c_adapter *parent;
 	int (*deselect) (struct i2c_adapter *, void *, u32);
 	unsigned initial_state, gpio_base;
 	int i, ret;
 
-	pdata = pdev->dev.platform_data;
-	if (!pdata) {
-		dev_err(&pdev->dev, "Missing platform data\n");
-		return -ENODEV;
+	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux) {
+		dev_err(&pdev->dev, "Cannot allocate gpiomux structure");
+		return -ENOMEM;
 	}
 
+	platform_set_drvdata(pdev, mux);
+
+	if (!pdev->dev.platform_data) {
+		ret = i2c_mux_gpio_probe_dt(mux, pdev);
+		if (ret < 0)
+			return ret;
+	} else
+		memcpy(&mux->data, pdev->dev.platform_data, sizeof(mux->data));
+
 	/*
 	 * If a GPIO chip name is provided, the GPIO pin numbers provided are
 	 * relative to its base GPIO number. Otherwise they are absolute.
 	 */
-	if (pdata->gpio_chip) {
+	if (mux->data.gpio_chip) {
 		struct gpio_chip *gpio;
 
-		gpio = gpiochip_find(pdata->gpio_chip,
+		gpio = gpiochip_find(mux->data.gpio_chip,
 				     match_gpio_chip_by_label);
 		if (!gpio)
 			return -EPROBE_DEFER;
@@ -89,49 +173,44 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 		gpio_base = 0;
 	}
 
-	parent = i2c_get_adapter(pdata->parent);
+	parent = i2c_get_adapter(mux->data.parent);
 	if (!parent) {
 		dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
-			pdata->parent);
+			mux->data.parent);
 		return -ENODEV;
 	}
 
-	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
-	if (!mux) {
-		ret = -ENOMEM;
-		goto alloc_failed;
-	}
-
 	mux->parent = parent;
-	mux->data = *pdata;
 	mux->gpio_base = gpio_base;
+
 	mux->adap = devm_kzalloc(&pdev->dev,
-				 sizeof(*mux->adap) * pdata->n_values,
+				 sizeof(*mux->adap) * mux->data.n_values,
 				 GFP_KERNEL);
 	if (!mux->adap) {
+		dev_err(&pdev->dev, "Cannot allocate i2c_adapter structure");
 		ret = -ENOMEM;
 		goto alloc_failed;
 	}
 
-	if (pdata->idle != I2C_MUX_GPIO_NO_IDLE) {
-		initial_state = pdata->idle;
+	if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE) {
+		initial_state = mux->data.idle;
 		deselect = i2c_mux_gpio_deselect;
 	} else {
-		initial_state = pdata->values[0];
+		initial_state = mux->data.values[0];
 		deselect = NULL;
 	}
 
-	for (i = 0; i < pdata->n_gpios; i++) {
-		ret = gpio_request(gpio_base + pdata->gpios[i], "i2c-mux-gpio");
+	for (i = 0; i < mux->data.n_gpios; i++) {
+		ret = gpio_request(gpio_base + mux->data.gpios[i], "i2c-mux-gpio");
 		if (ret)
 			goto err_request_gpio;
-		gpio_direction_output(gpio_base + pdata->gpios[i],
+		gpio_direction_output(gpio_base + mux->data.gpios[i],
 				      initial_state & (1 << i));
 	}
 
-	for (i = 0; i < pdata->n_values; i++) {
-		u32 nr = pdata->base_nr ? (pdata->base_nr + i) : 0;
-		unsigned int class = pdata->classes ? pdata->classes[i] : 0;
+	for (i = 0; i < mux->data.n_values; i++) {
+		u32 nr = mux->data.base_nr ? (mux->data.base_nr + i) : 0;
+		unsigned int class = mux->data.classes ? mux->data.classes[i] : 0;
 
 		mux->adap[i] = i2c_add_mux_adapter(parent, &pdev->dev, mux, nr,
 						   i, class,
@@ -144,19 +223,17 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 	}
 
 	dev_info(&pdev->dev, "%d port mux on %s adapter\n",
-		 pdata->n_values, parent->name);
-
-	platform_set_drvdata(pdev, mux);
+		 mux->data.n_values, parent->name);
 
 	return 0;
 
 add_adapter_failed:
 	for (; i > 0; i--)
 		i2c_del_mux_adapter(mux->adap[i - 1]);
-	i = pdata->n_gpios;
+	i = mux->data.n_gpios;
 err_request_gpio:
 	for (; i > 0; i--)
-		gpio_free(gpio_base + pdata->gpios[i - 1]);
+		gpio_free(gpio_base + mux->data.gpios[i - 1]);
 alloc_failed:
 	i2c_put_adapter(parent);
 
@@ -180,12 +257,19 @@ static int __devexit i2c_mux_gpio_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct of_device_id i2c_mux_gpio_of_match[] __devinitconst = {
+	{ .compatible = "i2c-mux-gpio", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, i2c_mux_gpio_of_match);
+
 static struct platform_driver i2c_mux_gpio_driver = {
 	.probe	= i2c_mux_gpio_probe,
 	.remove	= __devexit_p(i2c_mux_gpio_remove),
 	.driver	= {
 		.owner	= THIS_MODULE,
 		.name	= "i2c-mux-gpio",
+		.of_match_table = of_match_ptr(i2c_mux_gpio_of_match),
 	},
 };
 
-- 
1.7.9.5

[PATCH 1/2] i2c: mux: Add dt support to i2c-mux-gpio driver

[Maxime Ripard]

Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
---
 .../devicetree/bindings/i2c/i2c-mux-gpio.txt       |   81 +++++++++++
 drivers/i2c/muxes/i2c-mux-gpio.c                   |  146 +++++++++++++++-----
 2 files changed, 196 insertions(+), 31 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt

diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
new file mode 100644
index 0000000..66709a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
@@ -0,0 +1,81 @@
+GPIO-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+                                  +-----+  +-----+
+                                  | dev |  | dev |
+    +------------+                +-----+  +-----+
+    | SoC        |                   |        |
+    |            |          /--------+--------+
+    |   +------+ |  +------+    child bus A, on GPIO value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
+    |            |     |    \----------+--------+--------+
+    |   +------+ |     |               |        |        |
+    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
+    |   +------+ |                  | dev |  | dev |  | dev |
+    +------------+                  +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-gpio
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-gpios: list of gpios used to control the muxer
+* Standard I2C mux properties. See mux.txt in this directory.
+* I2C child bus nodes. See mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the revelant node's reg property will be output using the list of
+GPIOs, the first in the list holding the least-significant value.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+GPIOs will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c at 1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled at 3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c at 3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555 at 20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
diff --git a/drivers/i2c/muxes/i2c-mux-gpio.c b/drivers/i2c/muxes/i2c-mux-gpio.c
index 566a675..e446f05 100644
--- a/drivers/i2c/muxes/i2c-mux-gpio.c
+++ b/drivers/i2c/muxes/i2c-mux-gpio.c
@@ -16,6 +16,8 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/gpio.h>
+#include <linux/of_i2c.h>
+#include <linux/of_gpio.h>
 
 struct gpiomux {
 	struct i2c_adapter *parent;
@@ -57,29 +59,111 @@ static int __devinit match_gpio_chip_by_label(struct gpio_chip *chip,
 	return !strcmp(chip->label, data);
 }
 
+#ifdef CONFIG_OF
+static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *adapter_np, *child;
+	struct i2c_adapter *adapter;
+	unsigned *values, *gpios;
+	int i = 0;
+
+	if (!np)
+		return -ENODEV;
+
+	adapter_np = of_parse_phandle(np, "i2c-parent", 0);
+	if (!adapter_np) {
+		dev_err(&pdev->dev, "Cannot parse i2c-parent\n");
+		return -ENODEV;
+	}
+	adapter = of_find_i2c_adapter_by_node(adapter_np);
+	if (!adapter) {
+		dev_err(&pdev->dev, "Cannot find parent bus\n");
+		return -ENODEV;
+	}
+	mux->data.parent = i2c_adapter_id(adapter);
+	put_device(&adapter->dev);
+
+	mux->data.n_values = of_get_child_count(np);
+
+	values = devm_kzalloc(&pdev->dev,
+			      sizeof(*mux->data.values) * mux->data.n_values,
+			      GFP_KERNEL);
+	if (!values) {
+		dev_err(&pdev->dev, "Cannot allocate values array");
+		return -ENOMEM;
+	}
+
+	for_each_child_of_node(np, child) {
+		of_property_read_u32(child, "reg", values + i);
+		i++;
+	}
+	mux->data.values = values;
+
+	if (of_property_read_u32(np, "idle-state", &mux->data.idle))
+		mux->data.idle = I2C_MUX_GPIO_NO_IDLE;
+
+	mux->data.n_gpios = of_gpio_named_count(np, "mux-gpios");
+	if (mux->data.n_gpios < 0) {
+		dev_err(&pdev->dev, "Missing mux-gpios property in the DT.\n");
+		return -EINVAL;
+	}
+
+	gpios = devm_kzalloc(&pdev->dev,
+			     sizeof(*mux->data.gpios) * mux->data.n_gpios,
+                             GFP_KERNEL);
+	if (!gpios) {
+		dev_err(&pdev->dev, "Cannot allocate gpios array");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < mux->data.n_gpios; i++)
+		gpios[i] = of_get_named_gpio(np, "mux-gpios", i);
+
+	mux->data.gpios = gpios;
+
+	return 0;
+}
+#else
+static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
 static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 {
 	struct gpiomux *mux;
-	struct i2c_mux_gpio_platform_data *pdata;
 	struct i2c_adapter *parent;
 	int (*deselect) (struct i2c_adapter *, void *, u32);
 	unsigned initial_state, gpio_base;
 	int i, ret;
 
-	pdata = pdev->dev.platform_data;
-	if (!pdata) {
-		dev_err(&pdev->dev, "Missing platform data\n");
-		return -ENODEV;
+	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux) {
+		dev_err(&pdev->dev, "Cannot allocate gpiomux structure");
+		return -ENOMEM;
 	}
 
+	platform_set_drvdata(pdev, mux);
+
+	if (!pdev->dev.platform_data) {
+		ret = i2c_mux_gpio_probe_dt(mux, pdev);
+		if (ret < 0)
+			return ret;
+	} else
+		memcpy(&mux->data, pdev->dev.platform_data, sizeof(mux->data));
+
 	/*
 	 * If a GPIO chip name is provided, the GPIO pin numbers provided are
 	 * relative to its base GPIO number. Otherwise they are absolute.
 	 */
-	if (pdata->gpio_chip) {
+	if (mux->data.gpio_chip) {
 		struct gpio_chip *gpio;
 
-		gpio = gpiochip_find(pdata->gpio_chip,
+		gpio = gpiochip_find(mux->data.gpio_chip,
 				     match_gpio_chip_by_label);
 		if (!gpio)
 			return -EPROBE_DEFER;
@@ -89,49 +173,44 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 		gpio_base = 0;
 	}
 
-	parent = i2c_get_adapter(pdata->parent);
+	parent = i2c_get_adapter(mux->data.parent);
 	if (!parent) {
 		dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
-			pdata->parent);
+			mux->data.parent);
 		return -ENODEV;
 	}
 
-	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
-	if (!mux) {
-		ret = -ENOMEM;
-		goto alloc_failed;
-	}
-
 	mux->parent = parent;
-	mux->data = *pdata;
 	mux->gpio_base = gpio_base;
+
 	mux->adap = devm_kzalloc(&pdev->dev,
-				 sizeof(*mux->adap) * pdata->n_values,
+				 sizeof(*mux->adap) * mux->data.n_values,
 				 GFP_KERNEL);
 	if (!mux->adap) {
+		dev_err(&pdev->dev, "Cannot allocate i2c_adapter structure");
 		ret = -ENOMEM;
 		goto alloc_failed;
 	}
 
-	if (pdata->idle != I2C_MUX_GPIO_NO_IDLE) {
-		initial_state = pdata->idle;
+	if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE) {
+		initial_state = mux->data.idle;
 		deselect = i2c_mux_gpio_deselect;
 	} else {
-		initial_state = pdata->values[0];
+		initial_state = mux->data.values[0];
 		deselect = NULL;
 	}
 
-	for (i = 0; i < pdata->n_gpios; i++) {
-		ret = gpio_request(gpio_base + pdata->gpios[i], "i2c-mux-gpio");
+	for (i = 0; i < mux->data.n_gpios; i++) {
+		ret = gpio_request(gpio_base + mux->data.gpios[i], "i2c-mux-gpio");
 		if (ret)
 			goto err_request_gpio;
-		gpio_direction_output(gpio_base + pdata->gpios[i],
+		gpio_direction_output(gpio_base + mux->data.gpios[i],
 				      initial_state & (1 << i));
 	}
 
-	for (i = 0; i < pdata->n_values; i++) {
-		u32 nr = pdata->base_nr ? (pdata->base_nr + i) : 0;
-		unsigned int class = pdata->classes ? pdata->classes[i] : 0;
+	for (i = 0; i < mux->data.n_values; i++) {
+		u32 nr = mux->data.base_nr ? (mux->data.base_nr + i) : 0;
+		unsigned int class = mux->data.classes ? mux->data.classes[i] : 0;
 
 		mux->adap[i] = i2c_add_mux_adapter(parent, &pdev->dev, mux, nr,
 						   i, class,
@@ -144,19 +223,17 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
 	}
 
 	dev_info(&pdev->dev, "%d port mux on %s adapter\n",
-		 pdata->n_values, parent->name);
-
-	platform_set_drvdata(pdev, mux);
+		 mux->data.n_values, parent->name);
 
 	return 0;
 
 add_adapter_failed:
 	for (; i > 0; i--)
 		i2c_del_mux_adapter(mux->adap[i - 1]);
-	i = pdata->n_gpios;
+	i = mux->data.n_gpios;
 err_request_gpio:
 	for (; i > 0; i--)
-		gpio_free(gpio_base + pdata->gpios[i - 1]);
+		gpio_free(gpio_base + mux->data.gpios[i - 1]);
 alloc_failed:
 	i2c_put_adapter(parent);
 
@@ -180,12 +257,19 @@ static int __devexit i2c_mux_gpio_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct of_device_id i2c_mux_gpio_of_match[] __devinitconst = {
+	{ .compatible = "i2c-mux-gpio", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, i2c_mux_gpio_of_match);
+
 static struct platform_driver i2c_mux_gpio_driver = {
 	.probe	= i2c_mux_gpio_probe,
 	.remove	= __devexit_p(i2c_mux_gpio_remove),
 	.driver	= {
 		.owner	= THIS_MODULE,
 		.name	= "i2c-mux-gpio",
+		.of_match_table = of_match_ptr(i2c_mux_gpio_of_match),
 	},
 };
 
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c@0 {
+					reg = <0>;
+				};
+
+				i2c@1 {
+					reg = <1>;
+				};
+
+				i2c@2 {
+					reg = <2>;
+				};
+
+				i2c@3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c at 0 {
+					reg = <0>;
+				};
+
+				i2c at 1 {
+					reg = <1>;
+				};
+
+				i2c at 2 {
+					reg = <2>;
+				};
+
+				i2c at 3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy at 8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

Re: [PATCH 1/2] i2c: mux: Add dt support to i2c-mux-gpio driver

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 769 bytes --]

On Thu, Oct 25, 2012 at 06:23:53PM +0200, Maxime Ripard wrote:
> Allow the i2c-mux-gpio to be used by a device tree enabled device. The
> bindings are inspired by the one found in the i2c-mux-pinctrl driver.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Reviewed-by: Stephen Warren <swarren-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> Acked-by: Peter Korsgaard <peter.korsgaard-ob4gmnvZ1/cAvxtiuMwx3w@public.gmane.org>

checkpatch found a whitespace error in line 115, please run it before
submitting. Fixed that and pushed to for-next. Thanks.

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 198 bytes --]

[PATCH 1/2] i2c: mux: Add dt support to i2c-mux-gpio driver

[Wolfram Sang]

On Thu, Oct 25, 2012 at 06:23:53PM +0200, Maxime Ripard wrote:
> Allow the i2c-mux-gpio to be used by a device tree enabled device. The
> bindings are inspired by the one found in the i2c-mux-pinctrl driver.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Reviewed-by: Stephen Warren <swarren@nvidia.com>
> Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

checkpatch found a whitespace error in line 115, please run it before
submitting. Fixed that and pushed to for-next. Thanks.

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121116/e472467c/attachment.sig>

Re: [PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 603 bytes --]

On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> GPIO expander eventually.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>

Shawn, I pushed the needed code to my for-next now. So you could apply
this patch for 3.8 or give an ack in case you want me to pick it via
i2c.

Regards,

   Wolfram

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 198 bytes --]

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Wolfram Sang]

On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> GPIO expander eventually.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Shawn, I pushed the needed code to my for-next now. So you could apply
this patch for 3.8 or give an ack in case you want me to pick it via
i2c.

Regards,

   Wolfram

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121116/9c047769/attachment.sig>

Re: [PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 958 bytes --]

On Fri, Nov 16, 2012 at 10:25:32PM +0800, Shawn Guo wrote:
> On Fri, Nov 16, 2012 at 09:32:18AM +0100, Wolfram Sang wrote:
> > On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> > > This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> > > GPIO expander eventually.
> > > 
> > > Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> > 
> > Shawn, I pushed the needed code to my for-next now. So you could apply
> > this patch for 3.8 or give an ack in case you want me to pick it via
> > i2c.
> > 
> I have already sent mxs 3.8 stuff to arm-soc, so please have it go via
> i2c tree.  Thanks.
> 
> Acked-by: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>

OK. Applied to my for-next, thanks!

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 198 bytes --]

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Wolfram Sang]

On Fri, Nov 16, 2012 at 10:25:32PM +0800, Shawn Guo wrote:
> On Fri, Nov 16, 2012 at 09:32:18AM +0100, Wolfram Sang wrote:
> > On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> > > This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> > > GPIO expander eventually.
> > > 
> > > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> > 
> > Shawn, I pushed the needed code to my for-next now. So you could apply
> > this patch for 3.8 or give an ack in case you want me to pick it via
> > i2c.
> > 
> I have already sent mxs 3.8 stuff to arm-soc, so please have it go via
> i2c tree.  Thanks.
> 
> Acked-by: Shawn Guo <shawn.guo@linaro.org>

OK. Applied to my for-next, thanks!

-- 
Pengutronix e.K.                           | Wolfram Sang                |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121116/a635c146/attachment.sig>

Re: [PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Shawn Guo]

On Fri, Nov 16, 2012 at 09:32:18AM +0100, Wolfram Sang wrote:
> On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> > This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> > GPIO expander eventually.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> 
> Shawn, I pushed the needed code to my for-next now. So you could apply
> this patch for 3.8 or give an ack in case you want me to pick it via
> i2c.
> 
I have already sent mxs 3.8 stuff to arm-soc, so please have it go via
i2c tree.  Thanks.

Acked-by: Shawn Guo <shawn.guo@linaro.org>

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Shawn Guo]

On Fri, Nov 16, 2012 at 09:32:18AM +0100, Wolfram Sang wrote:
> On Thu, Oct 25, 2012 at 06:23:54PM +0200, Maxime Ripard wrote:
> > This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
> > GPIO expander eventually.
> > 
> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> 
> Shawn, I pushed the needed code to my for-next now. So you could apply
> this patch for 3.8 or give an ack in case you want me to pick it via
> i2c.
> 
I have already sent mxs 3.8 stuff to arm-soc, so please have it go via
i2c tree.  Thanks.

Acked-by: Shawn Guo <shawn.guo@linaro.org>

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c@0 {
+					reg = <0>;
+				};
+
+				i2c@1 {
+					reg = <1>;
+				};
+
+				i2c@2 {
+					reg = <2>;
+				};
+
+				i2c@3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c at 0 {
+					reg = <0>;
+				};
+
+				i2c at 1 {
+					reg = <1>;
+				};
+
+				i2c at 2 {
+					reg = <2>;
+				};
+
+				i2c at 3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy at 8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c@0 {
+					reg = <0>;
+				};
+
+				i2c@1 {
+					reg = <1>;
+				};
+
+				i2c@2 {
+					reg = <2>;
+				};
+
+				i2c@3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c at 0 {
+					reg = <0>;
+				};
+
+				i2c at 1 {
+					reg = <1>;
+				};
+
+				i2c at 2 {
+					reg = <2>;
+				};
+
+				i2c at 3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy at 8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c@0 {
+					reg = <0>;
+				};
+
+				i2c@1 {
+					reg = <1>;
+				};
+
+				i2c@2 {
+					reg = <2>;
+				};
+
+				i2c@3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5

[PATCH 2/2] ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049

[Maxime Ripard]

This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
 arch/arm/boot/dts/imx28-cfa10049.dts |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 97ee098..2cda823 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -76,6 +76,30 @@
 				status = "okay";
 			};
 
+			i2cmux {
+				compatible = "i2c-mux-gpio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+				i2c-parent = <&i2c1>;
+
+				i2c at 0 {
+					reg = <0>;
+				};
+
+				i2c at 1 {
+					reg = <1>;
+				};
+
+				i2c at 2 {
+					reg = <2>;
+				};
+
+				i2c at 3 {
+					reg = <3>;
+				};
+			};
+
 			usbphy1: usbphy at 8007e000 {
 				status = "okay";
 			};
-- 
1.7.9.5