From: Simon Horman <horms@verge.net.au> To: linux-arm-kernel@lists.infradead.org Subject: Mainline kernel on snowball Date: Thu, 25 Jul 2013 05:23:17 +0000 [thread overview] Message-ID: <20130725052317.GA25854@verge.net.au> (raw) Hi, I apologise for the naïve nature of this question, but I do not seem to be able to make any progress of my own accord. I would like to boot the mainline kernel - ideally v3.10 and v3.11-rcX - on snowball. The reason being to verify CPU hotplug which seems to be broken on shmobile, though that is tangential to this post. My procedure, which does not work, is as follows. I have tried a number of different versions all with roughly the same result. 1. Build kernel # git checkout v3.10.2 # I have tried several over versions too. # make u8500_defconfig Edit .config to enable CONFIG_ARM_APPENDED_DTB # LOADADDR=0x100000 make uImage dtbs 2. Append dtb to zImage and recreate uImage mv arch/arm/boot/zImage arch/arm/boot/zImage.tmp cat arch/arm/boot/zImage.tmp arch/arm/boot/dts/snowball.dtb /bin/sh scripts/mkuboot.sh \ -A arm -O linux -C none -T kernel \ -a 0x100000 -e 0x100000 -n 'Linux-3.10.2' \ -d arch/arm/boot/zImage arch/arm/boot/uImage 3. Boot uImage from u-boot Snowball $ setenv ethaddr 3e:c4:73:05:d1:a1 Snowball $ bootp;bootm smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 3e:c4:73:05:d1:a1 BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 44 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 44 DHCP client bound to address 10.3.3.146 Using smc911x-0 device TFTP from server 10.3.3.135; our IP address is 10.3.3.146 Filename 'snowball/uImage'. Load address: 0x100000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## done Bytes transferred = 2540191 (26c29f hex) ## Booting kernel from Legacy Image at 00100000 ... Image Name: 'Linux-3.10.2' Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2540127 Bytes = 2.4 MB Load Address: 00100000 Entry Point: 00100000 XIP Kernel Image ... OK OK Starting kernel ... This is as far as it gets.
WARNING: multiple messages have this Message-ID (diff)
From: horms@verge.net.au (Simon Horman) To: linux-arm-kernel@lists.infradead.org Subject: Mainline kernel on snowball Date: Thu, 25 Jul 2013 14:23:17 +0900 [thread overview] Message-ID: <20130725052317.GA25854@verge.net.au> (raw) Hi, I apologise for the na?ve nature of this question, but I do not seem to be able to make any progress of my own accord. I would like to boot the mainline kernel - ideally v3.10 and v3.11-rcX - on snowball. The reason being to verify CPU hotplug which seems to be broken on shmobile, though that is tangential to this post. My procedure, which does not work, is as follows. I have tried a number of different versions all with roughly the same result. 1. Build kernel # git checkout v3.10.2 # I have tried several over versions too. # make u8500_defconfig Edit .config to enable CONFIG_ARM_APPENDED_DTB # LOADADDR=0x100000 make uImage dtbs 2. Append dtb to zImage and recreate uImage mv arch/arm/boot/zImage arch/arm/boot/zImage.tmp cat arch/arm/boot/zImage.tmp arch/arm/boot/dts/snowball.dtb /bin/sh scripts/mkuboot.sh \ -A arm -O linux -C none -T kernel \ -a 0x100000 -e 0x100000 -n 'Linux-3.10.2' \ -d arch/arm/boot/zImage arch/arm/boot/uImage 3. Boot uImage from u-boot Snowball $ setenv ethaddr 3e:c4:73:05:d1:a1 Snowball $ bootp;bootm smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 3e:c4:73:05:d1:a1 BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 44 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 44 DHCP client bound to address 10.3.3.146 Using smc911x-0 device TFTP from server 10.3.3.135; our IP address is 10.3.3.146 Filename 'snowball/uImage'. Load address: 0x100000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## done Bytes transferred = 2540191 (26c29f hex) ## Booting kernel from Legacy Image at 00100000 ... Image Name: 'Linux-3.10.2' Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2540127 Bytes = 2.4 MB Load Address: 00100000 Entry Point: 00100000 XIP Kernel Image ... OK OK Starting kernel ... This is as far as it gets.
next reply other threads:[~2013-07-25 5:23 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2013-07-25 5:23 Simon Horman [this message] 2013-07-25 5:23 ` Mainline kernel on snowball Simon Horman 2013-07-25 5:40 ` Willy Tarreau 2013-07-25 5:40 ` Willy Tarreau 2013-07-25 7:25 ` Simon Horman 2013-07-25 7:25 ` Simon Horman 2013-07-25 7:52 ` Willy Tarreau 2013-07-25 7:52 ` Willy Tarreau 2013-07-25 8:26 ` Simon Horman 2013-07-25 8:26 ` Simon Horman 2013-07-25 8:36 ` Willy Tarreau 2013-07-25 8:36 ` Willy Tarreau 2013-07-25 6:41 ` Uwe Kleine-König 2013-07-25 6:41 ` Uwe Kleine-König 2013-07-25 7:22 ` Simon Horman 2013-07-25 7:22 ` Simon Horman 2013-07-25 9:27 ` Linus Walleij 2013-07-25 9:27 ` Linus Walleij
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20130725052317.GA25854@verge.net.au \ --to=horms@verge.net.au \ --cc=linux-arm-kernel@lists.infradead.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.