From: "Heiko Stübner" <heiko@sntech.de> To: Kukjin Kim <kgene.kim@samsung.com> Cc: t.figa@samsung.com, mturquette@linaro.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org Subject: [PATCH 01/12] ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf Date: Fri, 13 Dec 2013 13:57:19 +0100 [thread overview] Message-ID: <201312131357.19899.heiko@sntech.de> (raw) In-Reply-To: <201312131356.40755.heiko@sntech.de> The s3c24xx cpufreq driver needs to change the mpll speed and was doing this by writing raw values from a translation table into the MPLLCON register. Change this to use a regular clk_set_rate call when using the common clock framework and only write the raw value in the samsung_clock case. Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- arch/arm/mach-s3c24xx/cpufreq-utils.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/mach-s3c24xx/cpufreq-utils.c b/arch/arm/mach-s3c24xx/cpufreq-utils.c index 2a0aa56..680a031 100644 --- a/arch/arm/mach-s3c24xx/cpufreq-utils.c +++ b/arch/arm/mach-s3c24xx/cpufreq-utils.c @@ -14,6 +14,7 @@ #include <linux/errno.h> #include <linux/cpufreq.h> #include <linux/io.h> +#include <linux/clk.h> #include <mach/map.h> #include <mach/regs-clock.h> @@ -60,5 +61,17 @@ void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) */ void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg) { +#ifdef CONFIG_SAMSUNG_CLOCK __raw_writel(cfg->pll.driver_data, S3C2410_MPLLCON); +#endif + +#ifdef CONFIG_COMMON_CLK + struct clk *mpll = clk_get(NULL, "mpll"); + if (IS_ERR(mpll)) + return; + + clk_set_rate(mpll, cfg->pll.frequency); + + clk_put(mpll); +#endif } -- 1.7.10.4
WARNING: multiple messages have this Message-ID (diff)
From: heiko@sntech.de (Heiko Stübner) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 01/12] ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf Date: Fri, 13 Dec 2013 13:57:19 +0100 [thread overview] Message-ID: <201312131357.19899.heiko@sntech.de> (raw) In-Reply-To: <201312131356.40755.heiko@sntech.de> The s3c24xx cpufreq driver needs to change the mpll speed and was doing this by writing raw values from a translation table into the MPLLCON register. Change this to use a regular clk_set_rate call when using the common clock framework and only write the raw value in the samsung_clock case. Signed-off-by: Heiko Stuebner <heiko@sntech.de> --- arch/arm/mach-s3c24xx/cpufreq-utils.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/mach-s3c24xx/cpufreq-utils.c b/arch/arm/mach-s3c24xx/cpufreq-utils.c index 2a0aa56..680a031 100644 --- a/arch/arm/mach-s3c24xx/cpufreq-utils.c +++ b/arch/arm/mach-s3c24xx/cpufreq-utils.c @@ -14,6 +14,7 @@ #include <linux/errno.h> #include <linux/cpufreq.h> #include <linux/io.h> +#include <linux/clk.h> #include <mach/map.h> #include <mach/regs-clock.h> @@ -60,5 +61,17 @@ void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) */ void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg) { +#ifdef CONFIG_SAMSUNG_CLOCK __raw_writel(cfg->pll.driver_data, S3C2410_MPLLCON); +#endif + +#ifdef CONFIG_COMMON_CLK + struct clk *mpll = clk_get(NULL, "mpll"); + if (IS_ERR(mpll)) + return; + + clk_set_rate(mpll, cfg->pll.frequency); + + clk_put(mpll); +#endif } -- 1.7.10.4
next prev parent reply other threads:[~2013-12-13 12:57 UTC|newest] Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top 2013-12-13 12:56 [PATCH 00/12] ARM: S3C24XX: convert s3c2410, s3c2440 s3c2442 to common clock framework Heiko Stübner 2013-12-13 12:56 ` Heiko Stübner 2013-12-13 12:57 ` Heiko Stübner [this message] 2013-12-13 12:57 ` [PATCH 01/12] ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf Heiko Stübner 2014-02-08 20:23 ` Tomasz Figa 2014-02-08 20:23 ` Tomasz Figa 2013-12-13 12:59 ` [PATCH 02/12] dt-bindings: document s3c24xx controller for external clock output Heiko Stübner 2013-12-13 12:59 ` Heiko Stübner 2014-02-09 1:54 ` Tomasz Figa 2014-02-09 1:54 ` Tomasz Figa 2014-02-16 20:33 ` Heiko Stübner 2014-02-16 20:33 ` Heiko Stübner 2014-02-16 20:51 ` Tomasz Figa 2014-02-16 20:51 ` Tomasz Figa 2013-12-13 12:59 ` [PATCH 03/12] clk: samsung: add clock driver for external clock outputs Heiko Stübner 2013-12-13 12:59 ` Heiko Stübner 2013-12-31 19:46 ` Mike Turquette 2013-12-31 19:46 ` Mike Turquette 2014-02-09 2:25 ` Tomasz Figa 2014-02-09 2:25 ` Tomasz Figa 2013-12-13 13:00 ` [PATCH 04/12] ARM: S3C24XX: enable usage of common dclk if common clock framework is enabled Heiko Stübner 2013-12-13 13:00 ` Heiko Stübner 2013-12-13 13:00 ` [PATCH 05/12] ARM: S3C24XX: only store clock registers when old clock code is active Heiko Stübner 2013-12-13 13:00 ` Heiko Stübner 2013-12-13 13:00 ` [PATCH 06/12] clk: samsung: add plls used by the early s3c24xx cpus Heiko Stübner 2013-12-13 13:00 ` Heiko Stübner 2013-12-31 19:45 ` Mike Turquette 2013-12-31 19:45 ` Mike Turquette 2013-12-13 13:01 ` [PATCH 08/12] clk: samsung: add clock controller driver for s3c2410, s3c2440 and s3c2442 Heiko Stübner 2013-12-13 13:01 ` Heiko Stübner 2014-02-06 14:12 ` Mike Turquette 2014-02-06 14:12 ` Mike Turquette 2014-02-09 19:34 ` Tomasz Figa 2014-02-09 19:34 ` Tomasz Figa 2014-02-17 21:05 ` Heiko Stübner 2014-02-17 21:05 ` Heiko Stübner 2014-02-17 22:37 ` Tomasz Figa 2014-02-17 22:37 ` Tomasz Figa 2014-02-17 22:48 ` Heiko Stübner 2014-02-17 22:48 ` Heiko Stübner 2013-12-13 13:02 ` [PATCH 09/12] ARM: S3C24XX: add platform code for conversion to the common clock framework Heiko Stübner 2013-12-13 13:02 ` Heiko Stübner 2013-12-13 13:02 ` [PATCH 10/12] ARM: S3C24XX: convert s3c2440 and s3c2442 to " Heiko Stübner 2013-12-13 13:02 ` Heiko Stübner 2013-12-13 13:03 ` [PATCH 11/12] ARM: S3C24XX: convert s3c2410 " Heiko Stübner 2013-12-13 13:03 ` Heiko Stübner 2013-12-13 13:03 ` [PATCH 12/12] ARM: S3C24XX: remove legacy clock code Heiko Stübner 2013-12-13 13:03 ` Heiko Stübner 2014-02-09 19:56 ` [PATCH 00/12] ARM: S3C24XX: convert s3c2410, s3c2440 s3c2442 to common clock framework Tomasz Figa 2014-02-09 19:56 ` Tomasz Figa 2014-02-11 6:16 ` Kukjin Kim 2014-02-11 6:16 ` Kukjin Kim 2014-02-11 9:20 ` Heiko Stübner 2014-02-11 9:20 ` Heiko Stübner
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=201312131357.19899.heiko@sntech.de \ --to=heiko@sntech.de \ --cc=kgene.kim@samsung.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=mturquette@linaro.org \ --cc=t.figa@samsung.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.