* [PATCH v3 1/5] ARM: kirkwood: Add audio node to kirkwood.dtsi
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
@ 2014-02-25 17:33 ` Andrew Lunn
2014-02-25 17:34 ` [PATCH v3 2/5] ARM: kirkwood: Add i2c alias so setting bus number Andrew Lunn
` (4 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 17:33 UTC (permalink / raw)
To: linux-arm-kernel
The binding has existed for a while, so add the missing node so it can
be used by devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2:
Tabify
v3:
More tabification
---
arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 7b921b30cfcb..5a86fa820e12 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -310,5 +310,14 @@
#phy-cells = <0>;
status = "ok";
};
+
+ audio0: audio-controller at a0000 {
+ compatible = "marvell,kirkwood-audio";
+ reg = <0xa0000 0x2210>;
+ interrupts = <24>;
+ clocks = <&gate_clk 9>;
+ clock-names = "internal";
+ status = "disabled";
+ };
};
};
--
1.8.5.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v3 2/5] ARM: kirkwood: Add i2c alias so setting bus number
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
2014-02-25 17:33 ` [PATCH v3 1/5] ARM: kirkwood: Add audio node to kirkwood.dtsi Andrew Lunn
@ 2014-02-25 17:34 ` Andrew Lunn
2014-02-25 17:34 ` [PATCH v3 3/5] ARM: kirkwood: Add HP T5325 thin client Andrew Lunn
` (3 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 17:34 UTC (permalink / raw)
To: linux-arm-kernel
When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 5a86fa820e12..90384587c278 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -24,6 +24,7 @@
aliases {
gpio0 = &gpio0;
gpio1 = &gpio1;
+ i2c0 = &i2c0;
};
mbus {
@@ -111,7 +112,7 @@
clocks = <&gate_clk 7>;
};
- i2c at 11000 {
+ i2c0: i2c at 11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
#address-cells = <1>;
--
1.8.5.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v3 3/5] ARM: kirkwood: Add HP T5325 thin client
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
2014-02-25 17:33 ` [PATCH v3 1/5] ARM: kirkwood: Add audio node to kirkwood.dtsi Andrew Lunn
2014-02-25 17:34 ` [PATCH v3 2/5] ARM: kirkwood: Add i2c alias so setting bus number Andrew Lunn
@ 2014-02-25 17:34 ` Andrew Lunn
2014-02-25 17:34 ` [PATCH v3 4/5] ARM: kirkwood: Add dts file describing " Andrew Lunn
` (2 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 17:34 UTC (permalink / raw)
To: linux-arm-kernel
Convert the kirkwood t5325-setup.c to mostly device tree for
mach-mvebu. Part of the audio setup needs to remain in C for the
moment until suitable bindings are designed and implemented. So add
board code, triggered by the compatibility string.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2:
Remove spaces around KEY_POWER
Correct indentation of help text in Kconfig.
Put dts file into a patch of its own.
v3:
Defer dts Makefile patch to next patch.
---
arch/arm/mach-mvebu/Kconfig | 7 +++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/board-t5325.c | 41 +++++++++++++++++++++++++++++++++++++++
arch/arm/mach-mvebu/board.h | 22 +++++++++++++++++++++
arch/arm/mach-mvebu/kirkwood.c | 11 ++++++++++-
5 files changed, 81 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/mach-mvebu/board-t5325.c
create mode 100644 arch/arm/mach-mvebu/board.h
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 529f9164a8ca..5de7ada19191 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -92,6 +92,13 @@ config MACH_KIRKWOOD
Say 'Y' here if you want your kernel to support boards based
on the Marvell Kirkwood device tree.
+config MACH_T5325
+ bool "HP T5325 thin client"
+ depends on MACH_KIRKWOOD
+ help
+ Say 'Y' here if you want your kernel to support the
+ HP T5325 Thin client
+
endmenu
endif
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index d7672f1c8a6a..bbeb41ee3e75 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o
+obj-$(CONFIG_MACH_T5325) += board-t5325.o
diff --git a/arch/arm/mach-mvebu/board-t5325.c b/arch/arm/mach-mvebu/board-t5325.c
new file mode 100644
index 000000000000..65ace6db9f28
--- /dev/null
+++ b/arch/arm/mach-mvebu/board-t5325.c
@@ -0,0 +1,41 @@
+/*
+ * HP T5325 Board Setup
+ *
+ * Copyright (C) 2014
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <sound/alc5623.h>
+#include "board.h"
+
+static struct platform_device hp_t5325_audio_device = {
+ .name = "t5325-audio",
+ .id = -1,
+};
+
+static struct alc5623_platform_data alc5621_data = {
+ .add_ctrl = 0x3700,
+ .jack_det_ctrl = 0x4810,
+};
+
+static struct i2c_board_info i2c_board_info[] __initdata = {
+ {
+ I2C_BOARD_INFO("alc5621", 0x1a),
+ .platform_data = &alc5621_data,
+ },
+};
+
+void __init t5325_init(void)
+{
+ i2c_register_board_info(0, i2c_board_info, ARRAY_SIZE(i2c_board_info));
+ platform_device_register(&hp_t5325_audio_device);
+}
diff --git a/arch/arm/mach-mvebu/board.h b/arch/arm/mach-mvebu/board.h
new file mode 100644
index 000000000000..de7f0a191394
--- /dev/null
+++ b/arch/arm/mach-mvebu/board.h
@@ -0,0 +1,22 @@
+/*
+ * Board functions for Marvell System On Chip
+ *
+ * Copyright (C) 2014
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ARCH_MVEBU_BOARD_H
+#define __ARCH_MVEBU_BOARD_H
+
+#ifdef CONFIG_MACH_T5325
+void t5325_init(void);
+#else
+static inline void t5325_init(void) {};
+#endif
+
+#endif
diff --git a/arch/arm/mach-mvebu/kirkwood.c b/arch/arm/mach-mvebu/kirkwood.c
index 8a38b10532e5..120207fc36f1 100644
--- a/arch/arm/mach-mvebu/kirkwood.c
+++ b/arch/arm/mach-mvebu/kirkwood.c
@@ -25,6 +25,7 @@
#include "kirkwood.h"
#include "kirkwood-pm.h"
#include "common.h"
+#include "board.h"
static struct resource kirkwood_cpufreq_resources[] = {
[0] = {
@@ -158,6 +159,11 @@ void kirkwood_disable_mbus_error_propagation(void)
writel(readl(cpu_config) & ~CPU_CONFIG_ERROR_PROP, cpu_config);
}
+static struct of_dev_auxdata auxdata[] __initdata = {
+ OF_DEV_AUXDATA("marvell,kirkwood-audio", 0xf10a0000,
+ "mvebu-audio", NULL),
+ { /* sentinel */ }
+};
static void __init kirkwood_dt_init(void)
{
@@ -174,7 +180,10 @@ static void __init kirkwood_dt_init(void)
kirkwood_pm_init();
kirkwood_dt_eth_fixup();
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+ if (of_machine_is_compatible("hp,t5325"))
+ t5325_init();
+
+ of_platform_populate(NULL, of_default_bus_match_table, auxdata, NULL);
}
static const char * const kirkwood_dt_board_compat[] = {
--
1.8.5.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v3 4/5] ARM: kirkwood: Add dts file describing HP T5325 thin client
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
` (2 preceding siblings ...)
2014-02-25 17:34 ` [PATCH v3 3/5] ARM: kirkwood: Add HP T5325 thin client Andrew Lunn
@ 2014-02-25 17:34 ` Andrew Lunn
2014-02-25 17:34 ` [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig Andrew Lunn
2014-02-25 20:35 ` [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Jason Cooper
5 siblings, 0 replies; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 17:34 UTC (permalink / raw)
To: linux-arm-kernel
Describe the T5325 using device tree properties, where possible. The
first version of this file was produced by Thomas Petazzoni.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v3:
Makefile hunk.
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-t5325.dts | 208 +++++++++++++++++++++++++++++++++++
2 files changed, 209 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 436cc381db4a..20c152faa800 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -132,6 +132,7 @@ kirkwood := \
kirkwood-rs411.dtb \
kirkwood-sheevaplug.dtb \
kirkwood-sheevaplug-esata.dtb \
+ kirkwood-t5325.dtb \
kirkwood-topkick.dtb \
kirkwood-ts219-6281.dtb \
kirkwood-ts219-6282.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
new file mode 100644
index 000000000000..7d1c7677a18f
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -0,0 +1,208 @@
+/*
+ * Device Tree file for HP t5325 Thin Client"
+ *
+ * Copyright (C) 2014
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+*/
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "HP t5325 Thin Client";
+ compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+ pinctrl-0 = <&pmx_i2s &pmx_sysrst>;
+ pinctrl-names = "default";
+
+ pmx_button_power: pmx-button_power {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_off: pmx-power-off {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+
+ pmx_led: pmx-led {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_usb_sata_power_enable: pmx-usb-sata-power-enable {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * Redefined from kirkwood-6281.dtsi, because
+ * we don't use SPI CS on MPP0, but on MPP7.
+ */
+ pmx_spi: pmx-spi {
+ marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7";
+ marvell,function = "spi";
+ };
+
+ pmx_sysrst: pmx-sysrst {
+ marvell,pins = "mpp6";
+ marvell,function = "sysrst";
+ };
+
+ pmx_i2s: pmx-i2s {
+ marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42",
+ "mpp43";
+ marvell,function = "audio";
+ };
+ };
+
+ spi at 10600 {
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <86000000>;
+ reg = <0>;
+ mode = <0>;
+
+ partition at 0 {
+ reg = <0x0 0x80000>;
+ label = "u-boot";
+ };
+
+ partition at 1 {
+ reg = <0x80000 0x40000>;
+ label = "SSD firmware";
+ };
+
+ partition at 2 {
+ reg = <0xc0000 0x10000>;
+ label = "u-boot env";
+ };
+
+ partition at 3 {
+ reg = <0xd0000 0x10000>;
+ label = "permanent u-boot env";
+ };
+
+ partition at 4 {
+ reg = <0xd0000 0x10000>;
+ label = "permanent u-boot env";
+ };
+ };
+ };
+
+ i2c at 11000 {
+ status = "okay";
+
+ alc5621: alc5621 at 1a {
+ compatible = "realtek,alc5621";
+ reg = <0x1a>;
+ };
+ };
+
+ serial at 12000 {
+ status = "okay";
+ };
+
+ sata at 80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ audio: audio-controller at a0000 {
+ status = "okay";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_sata_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB-SATA Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_power>;
+ pinctrl-names = "default";
+
+ button at 1 {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_power_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ };
+
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy {
+ device_type = "ethernet-phy";
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port at 0 {
+ phy-handle = <ðphy0>;
+ };
+};
--
1.8.5.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
` (3 preceding siblings ...)
2014-02-25 17:34 ` [PATCH v3 4/5] ARM: kirkwood: Add dts file describing " Andrew Lunn
@ 2014-02-25 17:34 ` Andrew Lunn
2014-02-25 18:19 ` Arnd Bergmann
2014-02-25 20:35 ` [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Jason Cooper
5 siblings, 1 reply; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 17:34 UTC (permalink / raw)
To: linux-arm-kernel
The HP T5325 has a PCI based VGA controller. Add the frame buffer
driver, and frame buffer support to the defconfig's. Additionally
add the soc audio framework and the necessary codec.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/configs/multi_v5_defconfig | 9 +++++++++
arch/arm/configs/mvebu_v5_defconfig | 9 +++++++++
2 files changed, 18 insertions(+)
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index 2bc1e1707930..84ba24a0ead7 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_T5325=y
CONFIG_ARCH_MXC=y
CONFIG_MACH_IMX25_DT=y
CONFIG_MACH_IMX27_DT=y
@@ -101,6 +102,12 @@ CONFIG_THERMAL=y
CONFIG_KIRKWOOD_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_ORION_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_KIRKWOOD_SOC=y
+CONFIG_SND_KIRKWOOD_SOC_T5325=y
# CONFIG_ABX500_CORE is not set
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -150,6 +157,8 @@ CONFIG_RTC_DRV_S35390A=y
CONFIG_RTC_DRV_MV=y
CONFIG_DMADEVICES=y
CONFIG_MV_XOR=y
+CONFIG_STAGING=y
+CONFIG_FB_XGI=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
diff --git a/arch/arm/configs/mvebu_v5_defconfig b/arch/arm/configs/mvebu_v5_defconfig
index 2844636c0cf2..36484a37a1ca 100644
--- a/arch/arm/configs/mvebu_v5_defconfig
+++ b/arch/arm/configs/mvebu_v5_defconfig
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_T5325=y
# CONFIG_CPU_FEROCEON_OLD_ID is not set
CONFIG_PCI_MVEBU=y
CONFIG_PREEMPT=y
@@ -93,6 +94,12 @@ CONFIG_SENSORS_LM85=y
CONFIG_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_ORION_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_KIRKWOOD_SOC=y
+CONFIG_SND_KIRKWOOD_SOC_T5325=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_HID_DRAGONRISE=y
@@ -137,6 +144,8 @@ CONFIG_RTC_DRV_S35390A=y
CONFIG_RTC_DRV_MV=y
CONFIG_DMADEVICES=y
CONFIG_MV_XOR=y
+CONFIG_STAGING=y
+CONFIG_FB_XGI=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
--
1.8.5.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
2014-02-25 17:34 ` [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig Andrew Lunn
@ 2014-02-25 18:19 ` Arnd Bergmann
2014-02-25 18:53 ` Andrew Lunn
0 siblings, 1 reply; 10+ messages in thread
From: Arnd Bergmann @ 2014-02-25 18:19 UTC (permalink / raw)
To: linux-arm-kernel
On Tuesday 25 February 2014 18:34:03 Andrew Lunn wrote:
> The HP T5325 has a PCI based VGA controller. Add the frame buffer
> driver, and frame buffer support to the defconfig's. Additionally
> add the soc audio framework and the necessary codec.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
>
Does the VGA console still work with the new PCI driver?
I noticed we're not setting 'vga_base'.
Arnd
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
2014-02-25 18:19 ` Arnd Bergmann
@ 2014-02-25 18:53 ` Andrew Lunn
2014-02-25 19:04 ` Arnd Bergmann
0 siblings, 1 reply; 10+ messages in thread
From: Andrew Lunn @ 2014-02-25 18:53 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 25, 2014 at 07:19:33PM +0100, Arnd Bergmann wrote:
> On Tuesday 25 February 2014 18:34:03 Andrew Lunn wrote:
> > The HP T5325 has a PCI based VGA controller. Add the frame buffer
> > driver, and frame buffer support to the defconfig's. Additionally
> > add the soc audio framework and the necessary codec.
> >
> > Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> >
> Does the VGA console still work with the new PCI driver?
I've not plugged in a monitor, but i do see:
xgifb 0000:01:00.0: Relocate IO address: 10000 [00010030]
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
xgifb 0000:01:00.0: chipid = 32
xgifb: SR14=51 DramSzie 2000000 ChannelNum 1
xgifb 0000:01:00.0: Framebuffer at 0xe0000000, mapped to 0xe1000000, size 32768k
xgifb 0000:01:00.0: MMIO at 0xe4000000, mapped to 0xe0a00000, size 256k
xgifb 0000:01:00.0: No or unknown bridge type detected
xgifb: Default mode is 800x600x16 (60Hz)
so it looks like the frame buffer is happy.
I will see if i can find a cable and a monitor.
Andrew
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
2014-02-25 18:53 ` Andrew Lunn
@ 2014-02-25 19:04 ` Arnd Bergmann
0 siblings, 0 replies; 10+ messages in thread
From: Arnd Bergmann @ 2014-02-25 19:04 UTC (permalink / raw)
To: linux-arm-kernel
On Tuesday 25 February 2014 19:53:17 Andrew Lunn wrote:
> On Tue, Feb 25, 2014 at 07:19:33PM +0100, Arnd Bergmann wrote:
> > On Tuesday 25 February 2014 18:34:03 Andrew Lunn wrote:
> > > The HP T5325 has a PCI based VGA controller. Add the frame buffer
> > > driver, and frame buffer support to the defconfig's. Additionally
> > > add the soc audio framework and the necessary codec.
> > >
> > > Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> > >
> > Does the VGA console still work with the new PCI driver?
>
> I've not plugged in a monitor, but i do see:
>
> xgifb 0000:01:00.0: Relocate IO address: 10000 [00010030]
> PCI: enabling device 0000:00:01.0 (0140 -> 0143)
> xgifb 0000:01:00.0: chipid = 32
> xgifb: SR14=51 DramSzie 2000000 ChannelNum 1
> xgifb 0000:01:00.0: Framebuffer at 0xe0000000, mapped to 0xe1000000, size 32768k
> xgifb 0000:01:00.0: MMIO at 0xe4000000, mapped to 0xe0a00000, size 256k
> xgifb 0000:01:00.0: No or unknown bridge type detected
> xgifb: Default mode is 800x600x16 (60Hz)
>
> so it looks like the frame buffer is happy.
>
> I will see if i can find a cable and a monitor.
Ok, xgifb doesn't rely on vga_base, so that probably hasn't
changed. In theory, it could have worked with vgacon or
vga16fb before but that would be broken now.
Arnd
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 0/5] mvebu support for kirkwood HP T5325
2014-02-25 17:33 [PATCH v3 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
` (4 preceding siblings ...)
2014-02-25 17:34 ` [PATCH v3 5/5] ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig Andrew Lunn
@ 2014-02-25 20:35 ` Jason Cooper
5 siblings, 0 replies; 10+ messages in thread
From: Jason Cooper @ 2014-02-25 20:35 UTC (permalink / raw)
To: linux-arm-kernel
Andrew,
On Tue, Feb 25, 2014 at 06:33:58PM +0100, Andrew Lunn wrote:
> This patchset adds support to mvebu for the HP T5325 thin client.
> This is the first kirkwood device using device tree which supports
> audio. However the audio codec is missing a device tree binding, and
> simple-audio-card does not yet quite support all the properties needed
> for this hardware. So C code is used for the audio devices.
...
Applied as follows:
> Andrew Lunn (5):
> ARM: kirkwood: Add audio node to kirkwood.dtsi
> ARM: kirkwood: Add i2c alias so setting bus number
mvebu/dt
> ARM: kirkwood: Add HP T5325 thin client
mvebu/soc-kw
> ARM: kirkwood: Add dts file describing HP T5325 thin client
mvebu/dt
> ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
mvebu/defconfig
That's one more down!
thx,
Jason.
^ permalink raw reply [flat|nested] 10+ messages in thread