[RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.
---
 drivers/spi/Kconfig       |   6 +
 drivers/spi/Makefile      |   1 +
 drivers/spi/spi-bcm53xx.c | 283 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi-bcm53xx.h |  72 ++++++++++++
 4 files changed, 362 insertions(+)
 create mode 100644 drivers/spi/spi-bcm53xx.c
 create mode 100644 drivers/spi/spi-bcm53xx.h

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 62e2242..b14b829 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -112,6 +112,12 @@ config SPI_AU1550
 	  If you say yes to this option, support will be included for the
 	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 
+config SPI_BCM53XX
+	tristate "Broadcom BCM53xx SPI controller"
+	depends on ARCH_BCM_5301X
+	help
+          Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
+
 config SPI_BCM63XX
 	tristate "Broadcom BCM63xx SPI controller"
 	depends on BCM63XX
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 762da07..78f24ca 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
 obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
+obj-$(CONFIG_SPI_BCM53XX)		+= spi-bcm53xx.o
 obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
 obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o
 obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
diff --git a/drivers/spi/spi-bcm53xx.c b/drivers/spi/spi-bcm53xx.c
new file mode 100644
index 0000000..4ad0020
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.c
@@ -0,0 +1,283 @@
+#define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/bcma/bcma.h>
+#include <linux/spi/spi.h>
+
+#include "spi-bcm53xx.h"
+
+struct bcm53xxspi {
+	struct bcma_device *core;
+	struct spi_master *master;
+
+	size_t read_offset;
+};
+
+static inline u32 bcm53xxspi_read(struct bcm53xxspi *b53spi, u16 offset)
+{
+	return bcma_read32(b53spi->core, offset);
+}
+
+static inline void bcm53xxspi_write(struct bcm53xxspi *b53spi, u16 offset,
+				    u32 value)
+{
+	bcma_write32(b53spi->core, offset, value);
+}
+
+static inline unsigned int bcm53xxspi_calc_timeout(size_t len)
+{
+	return (len * 9000 / 13500000 * 110 / 100) + 1;
+}
+
+static int bcm53xxspi_wait(struct bcm53xxspi *b53spi, unsigned int timeout_ms)
+{
+	unsigned long deadline;
+	u32 tmp;
+
+	/* SPE bit has to be 0 before we read MSPI STATUS */
+	while (1) {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+		if (!(tmp & B53SPI_MSPI_SPCR2_SPE))
+			break;
+	}
+
+	/* Check status */
+	deadline = jiffies + timeout_ms * HZ / 1000;
+	do {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_MSPI_STATUS);
+		if (tmp & B53SPI_MSPI_MSPI_STATUS_SPIF) {
+			bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+			return 0;
+		}
+
+		cpu_relax();
+		udelay(100);
+	} while (!time_after_eq(jiffies, deadline));
+
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+
+	pr_err("Timeout waiting for SPI to be ready!\n");
+
+	return -EBUSY;
+}
+
+static void bcm53xxspi_buf_write(struct bcm53xxspi *b53spi, u8 *w_buf,
+				 size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < len; i++) {
+		/* Transmit Register File MSB */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_TXRAM + 4 * (i * 2),
+				 (unsigned int)w_buf[i]);
+	}
+
+	for (i = 0; i < len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	b53spi->read_offset = len;
+}
+
+static void bcm53xxspi_buf_read(struct bcm53xxspi *b53spi, u8 *r_buf,
+				size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < b53spi->read_offset + len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == b53spi->read_offset + len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP,
+			 b53spi->read_offset + len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	for (i = 0; i < len; ++i) {
+		int offset = b53spi->read_offset + i;
+
+		/* Data stored in the transmit register file LSB */
+		r_buf[i] = (u8)bcm53xxspi_read(b53spi, B53SPI_MSPI_RXRAM + 4 * (1 + offset * 2));
+	}
+
+	b53spi->read_offset = 0;
+}
+
+static int bcm53xxspi_transfer_one(struct spi_master *master,
+				   struct spi_device *spi,
+				   struct spi_transfer *t)
+{
+	struct bcm53xxspi *b53spi = spi_master_get_devdata(master);
+	u8 *buf;
+	size_t left;
+
+	if (t->tx_buf) {
+		buf = (u8 *)t->tx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_write = min_t(size_t, 16, left);
+			bool cont = left - to_write > 0;
+
+			bcm53xxspi_buf_write(b53spi, buf, to_write, cont);
+			left -= to_write;
+			buf += to_write;
+		}
+	}
+
+	if (t->rx_buf) {
+		buf = (u8 *)t->rx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_read = min_t(size_t, 16 - b53spi->read_offset,
+					       left);
+			bool cont = left - to_read > 0;
+
+			bcm53xxspi_buf_read(b53spi, buf, to_read, cont);
+			left -= to_read;
+			buf += to_read;
+		}
+	}
+
+	return 0;
+}
+
+/**************************************************
+ * BCMA
+ **************************************************/
+
+struct spi_board_info bcm53xx_info = {
+	.modalias	= "bcm53xxspiflash",
+};
+
+static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = {
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORETABLE_END
+};
+MODULE_DEVICE_TABLE(bcma, bcm53xxspi_bcma_tbl);
+
+static int bcm53xxspi_bcma_probe(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi;
+	struct spi_master *master;
+	int err;
+
+	if (core->bus->drv_cc.core->id.rev != 42) {
+		pr_err("SPI on SoC with unsupported ChipCommon rev\n");
+		return -ENOTSUPP;
+	}
+
+	master = spi_alloc_master(&core->dev, sizeof(*b53spi));
+	if (!master)
+		return -ENOMEM;
+
+	b53spi = spi_master_get_devdata(master);
+	b53spi->master = master;
+	b53spi->core = core;
+
+	master->transfer_one = bcm53xxspi_transfer_one;
+
+	bcma_set_drvdata(core, b53spi);
+
+	err = spi_register_master(master);
+	if (err) {
+		spi_master_put(master);
+		bcma_set_drvdata(core, NULL);
+		goto out;
+	}
+
+	/* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */
+	spi_new_device(master, &bcm53xx_info);
+
+out:
+	return err;
+}
+
+static void bcm53xxspi_bcma_remove(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi = bcma_get_drvdata(core);
+
+	spi_unregister_master(b53spi->master);
+}
+
+static struct bcma_driver bcm53xxspi_bcma_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= bcm53xxspi_bcma_tbl,
+	.probe		= bcm53xxspi_bcma_probe,
+	.remove		= bcm53xxspi_bcma_remove,
+};
+
+/**************************************************
+ * Init & exit
+ **************************************************/
+
+static int __init bcm53xxspi_module_init(void)
+{
+	int err = 0;
+
+	err = bcma_driver_register(&bcm53xxspi_bcma_driver);
+	if (err)
+		pr_err("Failed to register bcma driver: %d\n", err);
+
+	return err;
+}
+
+static void __exit bcm53xxspi_module_exit(void)
+{
+	bcma_driver_unregister(&bcm53xxspi_bcma_driver);
+}
+
+module_init(bcm53xxspi_module_init);
+module_exit(bcm53xxspi_module_exit);
diff --git a/drivers/spi/spi-bcm53xx.h b/drivers/spi/spi-bcm53xx.h
new file mode 100644
index 0000000..73575df
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.h
@@ -0,0 +1,72 @@
+#ifndef SPI_BCM53XX_H
+#define SPI_BCM53XX_H
+
+#define B53SPI_BSPI_REVISION_ID			0x000
+#define B53SPI_BSPI_SCRATCH			0x004
+#define B53SPI_BSPI_MAST_N_BOOT_CTRL		0x008
+#define B53SPI_BSPI_BUSY_STATUS			0x00c
+#define B53SPI_BSPI_INTR_STATUS			0x010
+#define B53SPI_BSPI_B0_STATUS			0x014
+#define B53SPI_BSPI_B0_CTRL			0x018
+#define B53SPI_BSPI_B1_STATUS			0x01c
+#define B53SPI_BSPI_B1_CTRL			0x020
+#define B53SPI_BSPI_STRAP_OVERRIDE_CTRL		0x024
+#define B53SPI_BSPI_FLEX_MODE_ENABLE		0x028
+#define B53SPI_BSPI_BITS_PER_CYCLE		0x02c
+#define B53SPI_BSPI_BITS_PER_PHASE		0x030
+#define B53SPI_BSPI_CMD_AND_MODE_BYTE		0x034
+#define B53SPI_BSPI_BSPI_FLASH_UPPER_ADDR_BYTE	0x038
+#define B53SPI_BSPI_BSPI_XOR_VALUE		0x03c
+#define B53SPI_BSPI_BSPI_XOR_ENABLE		0x040
+#define B53SPI_BSPI_BSPI_PIO_MODE_ENABLE	0x044
+#define B53SPI_BSPI_BSPI_PIO_IODIR		0x048
+#define B53SPI_BSPI_BSPI_PIO_DATA		0x04c
+
+/* RAF */
+#define B53SPI_RAF_START_ADDR			0x100
+#define B53SPI_RAF_NUM_WORDS			0x104
+#define B53SPI_RAF_CTRL				0x108
+#define B53SPI_RAF_FULLNESS			0x10c
+#define B53SPI_RAF_WATERMARK			0x110
+#define B53SPI_RAF_STATUS			0x114
+#define B53SPI_RAF_READ_DATA			0x118
+#define B53SPI_RAF_WORD_CNT			0x11c
+#define B53SPI_RAF_CURR_ADDR			0x120
+
+/* MSPI */
+#define B53SPI_MSPI_SPCR0_LSB			0x200
+#define B53SPI_MSPI_SPCR0_MSB			0x204
+#define B53SPI_MSPI_SPCR1_LSB			0x208
+#define B53SPI_MSPI_SPCR1_MSB			0x20c
+#define B53SPI_MSPI_NEWQP			0x210
+#define B53SPI_MSPI_ENDQP			0x214
+#define B53SPI_MSPI_SPCR2			0x218
+#define  B53SPI_MSPI_SPCR2_SPE			0x00000040
+#define  B53SPI_MSPI_SPCR2_CONT_AFTER_CMD	0x00000080
+#define B53SPI_MSPI_MSPI_STATUS			0x220
+#define  B53SPI_MSPI_MSPI_STATUS_SPIF		0x00000001
+#define B53SPI_MSPI_CPTQP			0x224
+#define B53SPI_MSPI_TXRAM			0x240 /* 32 registers, up to 0x2b8 */
+#define B53SPI_MSPI_RXRAM			0x2c0 /* 32 registers, up to 0x33c */
+#define B53SPI_MSPI_CDRAM			0x340 /* 16 registers, up to 0x37c */
+#define  B53SPI_CDRAM_PCS_PCS0			0x00000001
+#define  B53SPI_CDRAM_PCS_PCS1			0x00000002
+#define  B53SPI_CDRAM_PCS_PCS2			0x00000004
+#define  B53SPI_CDRAM_PCS_PCS3			0x00000008
+#define  B53SPI_CDRAM_PCS_DISABLE_ALL		0x0000000f
+#define  B53SPI_CDRAM_PCS_DSCK			0x00000010
+#define  B53SPI_CDRAM_BITSE			0x00000040
+#define  B53SPI_CDRAM_CONT			0x00000080
+#define B53SPI_MSPI_WRITE_LOCK			0x380
+#define B53SPI_MSPI_DISABLE_FLUSH_GEN		0x384
+
+/* Interrupt */
+#define B53SPI_INTR_RAF_LR_FULLNESS_REACHED	0x3a0
+#define B53SPI_INTR_RAF_LR_TRUNCATED		0x3a4
+#define B53SPI_INTR_RAF_LR_IMPATIENT		0x3a8
+#define B53SPI_INTR_RAF_LR_SESSION_DONE		0x3ac
+#define B53SPI_INTR_RAF_LR_OVERREAD		0x3b0
+#define B53SPI_INTR_MSPI_DONE			0x3b4
+#define B53SPI_INTR_MSPI_HALT_SET_TRANSACTION_DONE	0x3b8
+
+#endif /* SPI_BCM53XX_H */
-- 
1.8.4.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 667 bytes --]

On Wed, Aug 13, 2014 at 02:33:32PM +0200, Rafał Miłecki wrote:
> Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
> devices). If board has a serial flash, it's connected over SPI and the
> bcma bus includes a SPI controller. Example log from such a board:
> bus0: Found chip with id 53010, rev 0x00 and package 0x02
> (...)
> bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
> 
> This patch adds a bcma driver for SPI core, it registers SPI master
> controller and "bcm53xxspiflash" SPI device.
> ---

You need to sign off your changes, please see Documentation/SubmittingPatches
for details.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

On 13 August 2014 14:43, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
> On Wed, Aug 13, 2014 at 02:33:32PM +0200, Rafał Miłecki wrote:
>> Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
>> devices). If board has a serial flash, it's connected over SPI and the
>> bcma bus includes a SPI controller. Example log from such a board:
>> bus0: Found chip with id 53010, rev 0x00 and package 0x02
>> (...)
>> bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
>>
>> This patch adds a bcma driver for SPI core, it registers SPI master
>> controller and "bcm53xxspiflash" SPI device.
>> ---
>
> You need to sign off your changes, please see Documentation/SubmittingPatches
> for details.

Sure, I know, I just dropped S-o-B because it was RFC :)

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 504 bytes --]

On Wed, Aug 13, 2014 at 03:28:11PM +0200, Rafał Miłecki wrote:
> On 13 August 2014 14:43, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:

> > You need to sign off your changes, please see Documentation/SubmittingPatches
> > for details.

> Sure, I know, I just dropped S-o-B because it was RFC :)

Please don't do this, you've not asked any specific questions and there
normally shouldn't be any reason for a driver to be so problematic that
you'd not want it applying.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

On 13 August 2014 17:40, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
> On Wed, Aug 13, 2014 at 03:28:11PM +0200, Rafał Miłecki wrote:
>> On 13 August 2014 14:43, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
>
>> > You need to sign off your changes, please see Documentation/SubmittingPatches
>> > for details.
>
>> Sure, I know, I just dropped S-o-B because it was RFC :)
>
> Please don't do this, you've not asked any specific questions and there
> normally shouldn't be any reason for a driver to be so problematic that
> you'd not want it applying.

OK. It's my first contact with SPI ever, so I suspect I could
understand something incorrectly and did some things wrong in my
driver. In other words review of the whole code is appreciated :)
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [RFC][PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 319 bytes --]

On Wed, Aug 13, 2014 at 06:32:46PM +0200, Rafał Miłecki wrote:

> OK. It's my first contact with SPI ever, so I suspect I could
> understand something incorrectly and did some things wrong in my
> driver. In other words review of the whole code is appreciated :)

Please resend with a signoff in case it's OK.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.

Signed-off-by: Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Since RFC: Add Signed-off-by
	   Update to compile on top of for-next
---
 drivers/spi/Kconfig       |   6 +
 drivers/spi/Makefile      |   1 +
 drivers/spi/spi-bcm53xx.c | 283 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi-bcm53xx.h |  72 ++++++++++++
 4 files changed, 362 insertions(+)
 create mode 100644 drivers/spi/spi-bcm53xx.c
 create mode 100644 drivers/spi/spi-bcm53xx.h

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 62e2242..b14b829 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -112,6 +112,12 @@ config SPI_AU1550
 	  If you say yes to this option, support will be included for the
 	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 
+config SPI_BCM53XX
+	tristate "Broadcom BCM53xx SPI controller"
+	depends on ARCH_BCM_5301X
+	help
+          Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
+
 config SPI_BCM63XX
 	tristate "Broadcom BCM63xx SPI controller"
 	depends on BCM63XX
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 762da07..78f24ca 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
 obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
+obj-$(CONFIG_SPI_BCM53XX)		+= spi-bcm53xx.o
 obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
 obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o
 obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
diff --git a/drivers/spi/spi-bcm53xx.c b/drivers/spi/spi-bcm53xx.c
new file mode 100644
index 0000000..e8a16a3
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.c
@@ -0,0 +1,283 @@
+#define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/bcma/bcma.h>
+#include <linux/spi/spi.h>
+
+#include "spi-bcm53xx.h"
+
+struct bcm53xxspi {
+	struct bcma_device *core;
+	struct spi_master *master;
+
+	size_t read_offset;
+};
+
+static inline u32 bcm53xxspi_read(struct bcm53xxspi *b53spi, u16 offset)
+{
+	return bcma_read32(b53spi->core, offset);
+}
+
+static inline void bcm53xxspi_write(struct bcm53xxspi *b53spi, u16 offset,
+				    u32 value)
+{
+	bcma_write32(b53spi->core, offset, value);
+}
+
+static inline unsigned int bcm53xxspi_calc_timeout(size_t len)
+{
+	return (len * 9000 / 13500000 * 110 / 100) + 1;
+}
+
+static int bcm53xxspi_wait(struct bcm53xxspi *b53spi, unsigned int timeout_ms)
+{
+	unsigned long deadline;
+	u32 tmp;
+
+	/* SPE bit has to be 0 before we read MSPI STATUS */
+	while (1) {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+		if (!(tmp & B53SPI_MSPI_SPCR2_SPE))
+			break;
+	}
+
+	/* Check status */
+	deadline = jiffies + timeout_ms * HZ / 1000;
+	do {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_MSPI_STATUS);
+		if (tmp & B53SPI_MSPI_MSPI_STATUS_SPIF) {
+			bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+			return 0;
+		}
+
+		cpu_relax();
+		udelay(100);
+	} while (!time_after_eq(jiffies, deadline));
+
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+
+	pr_err("Timeout waiting for SPI to be ready!\n");
+
+	return -EBUSY;
+}
+
+static void bcm53xxspi_buf_write(struct bcm53xxspi *b53spi, u8 *w_buf,
+				 size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < len; i++) {
+		/* Transmit Register File MSB */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_TXRAM + 4 * (i * 2),
+				 (unsigned int)w_buf[i]);
+	}
+
+	for (i = 0; i < len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	b53spi->read_offset = len;
+}
+
+static void bcm53xxspi_buf_read(struct bcm53xxspi *b53spi, u8 *r_buf,
+				size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < b53spi->read_offset + len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == b53spi->read_offset + len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP,
+			 b53spi->read_offset + len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	for (i = 0; i < len; ++i) {
+		int offset = b53spi->read_offset + i;
+
+		/* Data stored in the transmit register file LSB */
+		r_buf[i] = (u8)bcm53xxspi_read(b53spi, B53SPI_MSPI_RXRAM + 4 * (1 + offset * 2));
+	}
+
+	b53spi->read_offset = 0;
+}
+
+static int bcm53xxspi_transfer_one(struct spi_master *master,
+				   struct spi_device *spi,
+				   struct spi_transfer *t)
+{
+	struct bcm53xxspi *b53spi = spi_master_get_devdata(master);
+	u8 *buf;
+	size_t left;
+
+	if (t->tx_buf) {
+		buf = (u8 *)t->tx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_write = min_t(size_t, 16, left);
+			bool cont = left - to_write > 0;
+
+			bcm53xxspi_buf_write(b53spi, buf, to_write, cont);
+			left -= to_write;
+			buf += to_write;
+		}
+	}
+
+	if (t->rx_buf) {
+		buf = (u8 *)t->rx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_read = min_t(size_t, 16 - b53spi->read_offset,
+					       left);
+			bool cont = left - to_read > 0;
+
+			bcm53xxspi_buf_read(b53spi, buf, to_read, cont);
+			left -= to_read;
+			buf += to_read;
+		}
+	}
+
+	return 0;
+}
+
+/**************************************************
+ * BCMA
+ **************************************************/
+
+struct spi_board_info bcm53xx_info = {
+	.modalias	= "bcm53xxspiflash",
+};
+
+static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = {
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORETABLE_END
+};
+MODULE_DEVICE_TABLE(bcma, bcm53xxspi_bcma_tbl);
+
+static int bcm53xxspi_bcma_probe(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi;
+	struct spi_master *master;
+	int err;
+
+	if (core->bus->drv_cc.core->id.rev != 42) {
+		pr_err("SPI on SoC with unsupported ChipCommon rev\n");
+		return -ENOTSUPP;
+	}
+
+	master = spi_alloc_master(&core->dev, sizeof(*b53spi));
+	if (!master)
+		return -ENOMEM;
+
+	b53spi = spi_master_get_devdata(master);
+	b53spi->master = master;
+	b53spi->core = core;
+
+	master->transfer_one = bcm53xxspi_transfer_one;
+
+	bcma_set_drvdata(core, b53spi);
+
+	err = spi_register_master(master);
+	if (err) {
+		spi_master_put(master);
+		bcma_set_drvdata(core, NULL);
+		goto out;
+	}
+
+	/* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */
+	spi_new_device(master, &bcm53xx_info);
+
+out:
+	return err;
+}
+
+static void bcm53xxspi_bcma_remove(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi = bcma_get_drvdata(core);
+
+	spi_unregister_master(b53spi->master);
+}
+
+static struct bcma_driver bcm53xxspi_bcma_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= bcm53xxspi_bcma_tbl,
+	.probe		= bcm53xxspi_bcma_probe,
+	.remove		= bcm53xxspi_bcma_remove,
+};
+
+/**************************************************
+ * Init & exit
+ **************************************************/
+
+static int __init bcm53xxspi_module_init(void)
+{
+	int err = 0;
+
+	err = bcma_driver_register(&bcm53xxspi_bcma_driver);
+	if (err)
+		pr_err("Failed to register bcma driver: %d\n", err);
+
+	return err;
+}
+
+static void __exit bcm53xxspi_module_exit(void)
+{
+	bcma_driver_unregister(&bcm53xxspi_bcma_driver);
+}
+
+module_init(bcm53xxspi_module_init);
+module_exit(bcm53xxspi_module_exit);
diff --git a/drivers/spi/spi-bcm53xx.h b/drivers/spi/spi-bcm53xx.h
new file mode 100644
index 0000000..73575df
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.h
@@ -0,0 +1,72 @@
+#ifndef SPI_BCM53XX_H
+#define SPI_BCM53XX_H
+
+#define B53SPI_BSPI_REVISION_ID			0x000
+#define B53SPI_BSPI_SCRATCH			0x004
+#define B53SPI_BSPI_MAST_N_BOOT_CTRL		0x008
+#define B53SPI_BSPI_BUSY_STATUS			0x00c
+#define B53SPI_BSPI_INTR_STATUS			0x010
+#define B53SPI_BSPI_B0_STATUS			0x014
+#define B53SPI_BSPI_B0_CTRL			0x018
+#define B53SPI_BSPI_B1_STATUS			0x01c
+#define B53SPI_BSPI_B1_CTRL			0x020
+#define B53SPI_BSPI_STRAP_OVERRIDE_CTRL		0x024
+#define B53SPI_BSPI_FLEX_MODE_ENABLE		0x028
+#define B53SPI_BSPI_BITS_PER_CYCLE		0x02c
+#define B53SPI_BSPI_BITS_PER_PHASE		0x030
+#define B53SPI_BSPI_CMD_AND_MODE_BYTE		0x034
+#define B53SPI_BSPI_BSPI_FLASH_UPPER_ADDR_BYTE	0x038
+#define B53SPI_BSPI_BSPI_XOR_VALUE		0x03c
+#define B53SPI_BSPI_BSPI_XOR_ENABLE		0x040
+#define B53SPI_BSPI_BSPI_PIO_MODE_ENABLE	0x044
+#define B53SPI_BSPI_BSPI_PIO_IODIR		0x048
+#define B53SPI_BSPI_BSPI_PIO_DATA		0x04c
+
+/* RAF */
+#define B53SPI_RAF_START_ADDR			0x100
+#define B53SPI_RAF_NUM_WORDS			0x104
+#define B53SPI_RAF_CTRL				0x108
+#define B53SPI_RAF_FULLNESS			0x10c
+#define B53SPI_RAF_WATERMARK			0x110
+#define B53SPI_RAF_STATUS			0x114
+#define B53SPI_RAF_READ_DATA			0x118
+#define B53SPI_RAF_WORD_CNT			0x11c
+#define B53SPI_RAF_CURR_ADDR			0x120
+
+/* MSPI */
+#define B53SPI_MSPI_SPCR0_LSB			0x200
+#define B53SPI_MSPI_SPCR0_MSB			0x204
+#define B53SPI_MSPI_SPCR1_LSB			0x208
+#define B53SPI_MSPI_SPCR1_MSB			0x20c
+#define B53SPI_MSPI_NEWQP			0x210
+#define B53SPI_MSPI_ENDQP			0x214
+#define B53SPI_MSPI_SPCR2			0x218
+#define  B53SPI_MSPI_SPCR2_SPE			0x00000040
+#define  B53SPI_MSPI_SPCR2_CONT_AFTER_CMD	0x00000080
+#define B53SPI_MSPI_MSPI_STATUS			0x220
+#define  B53SPI_MSPI_MSPI_STATUS_SPIF		0x00000001
+#define B53SPI_MSPI_CPTQP			0x224
+#define B53SPI_MSPI_TXRAM			0x240 /* 32 registers, up to 0x2b8 */
+#define B53SPI_MSPI_RXRAM			0x2c0 /* 32 registers, up to 0x33c */
+#define B53SPI_MSPI_CDRAM			0x340 /* 16 registers, up to 0x37c */
+#define  B53SPI_CDRAM_PCS_PCS0			0x00000001
+#define  B53SPI_CDRAM_PCS_PCS1			0x00000002
+#define  B53SPI_CDRAM_PCS_PCS2			0x00000004
+#define  B53SPI_CDRAM_PCS_PCS3			0x00000008
+#define  B53SPI_CDRAM_PCS_DISABLE_ALL		0x0000000f
+#define  B53SPI_CDRAM_PCS_DSCK			0x00000010
+#define  B53SPI_CDRAM_BITSE			0x00000040
+#define  B53SPI_CDRAM_CONT			0x00000080
+#define B53SPI_MSPI_WRITE_LOCK			0x380
+#define B53SPI_MSPI_DISABLE_FLUSH_GEN		0x384
+
+/* Interrupt */
+#define B53SPI_INTR_RAF_LR_FULLNESS_REACHED	0x3a0
+#define B53SPI_INTR_RAF_LR_TRUNCATED		0x3a4
+#define B53SPI_INTR_RAF_LR_IMPATIENT		0x3a8
+#define B53SPI_INTR_RAF_LR_SESSION_DONE		0x3ac
+#define B53SPI_INTR_RAF_LR_OVERREAD		0x3b0
+#define B53SPI_INTR_MSPI_DONE			0x3b4
+#define B53SPI_INTR_MSPI_HALT_SET_TRANSACTION_DONE	0x3b8
+
+#endif /* SPI_BCM53XX_H */
-- 
1.8.4.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 2388 bytes --]

On Sun, Aug 17, 2014 at 12:41:04AM +0200, Rafał Miłecki wrote:

> +static inline unsigned int bcm53xxspi_calc_timeout(size_t len)
> +{
> +	return (len * 9000 / 13500000 * 110 / 100) + 1;
> +}

Magic numbersr!

> +static int bcm53xxspi_wait(struct bcm53xxspi *b53spi, unsigned int timeout_ms)
> +{
> +	unsigned long deadline;
> +	u32 tmp;
> +
> +	/* SPE bit has to be 0 before we read MSPI STATUS */
> +	while (1) {
> +		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
> +		if (!(tmp & B53SPI_MSPI_SPCR2_SPE))
> +			break;
> +	}

This could block for ever, there should be a timeout of some kind.  I'd
also include a cpu_relax() in here since it's a busy wait.

> +static void bcm53xxspi_buf_write(struct bcm53xxspi *b53spi, u8 *w_buf,
> +				 size_t len, bool cont)
> +{
> +	u32 tmp;
> +	int i;
> +
> +	for (i = 0; i < len; i++) {
> +		/* Transmit Register File MSB */
> +		bcm53xxspi_write(b53spi, B53SPI_MSPI_TXRAM + 4 * (i * 2),
> +				 (unsigned int)w_buf[i]);
> +	}
> +
> +	for (i = 0; i < len; i++) {
> +		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
> +		      B53SPI_CDRAM_PCS_DSCK;
> +		if (!cont && i == len - 1)
> +			tmp &= ~B53SPI_CDRAM_CONT;
> +		tmp &= ~0x1;
> +		/* Command Register File */
> +		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
> +	}
> +
> +	/* Set queue pointers */
> +	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
> +	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
> +
> +	if (cont)
> +		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
> +
> +	/* Start SPI transfer */
> +	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
> +	tmp |= B53SPI_MSPI_SPCR2_SPE;
> +	if (cont)
> +		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
> +	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
> +
> +	/* Wait for SPI to finish */
> +	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));

This means we can only do unidirectonal transfers from the look of it -
is that a limitation of the hardware (from a quick read it seems like it
might be)?

> +	/* Wait for SPI to finish */
> +	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));

No interrupts?  This will busy wait for the entire transfer which seems
a bit much.

I'm also not seeing a set_cs() operation here.

> +	err = spi_register_master(master);
> +	if (err) {

devm_spi_register_master().

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

On 17 August 2014 16:21, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
> On Sun, Aug 17, 2014 at 12:41:04AM +0200, Rafał Miłecki wrote:
>
>> +static inline unsigned int bcm53xxspi_calc_timeout(size_t len)
>> +{
>> +     return (len * 9000 / 13500000 * 110 / 100) + 1;
>> +}
>
> Magic numbersr!

You just hit the reality of Broadcom world :( I'll try to improve it
at least a bit.

>> +static int bcm53xxspi_wait(struct bcm53xxspi *b53spi, unsigned int timeout_ms)
>> +{
>> +     unsigned long deadline;
>> +     u32 tmp;
>> +
>> +     /* SPE bit has to be 0 before we read MSPI STATUS */
>> +     while (1) {
>> +             tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
>> +             if (!(tmp & B53SPI_MSPI_SPCR2_SPE))
>> +                     break;
>> +     }
>
> This could block for ever, there should be a timeout of some kind.  I'd
> also include a cpu_relax() in here since it's a busy wait.

Right, will fix that.

>> +static void bcm53xxspi_buf_write(struct bcm53xxspi *b53spi, u8 *w_buf,
>> +                              size_t len, bool cont)
>> +{
>> +     u32 tmp;
>> +     int i;
>> +
>> +     for (i = 0; i < len; i++) {
>> +             /* Transmit Register File MSB */
>> +             bcm53xxspi_write(b53spi, B53SPI_MSPI_TXRAM + 4 * (i * 2),
>> +                              (unsigned int)w_buf[i]);
>> +     }
>> +
>> +     for (i = 0; i < len; i++) {
>> +             tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
>> +                   B53SPI_CDRAM_PCS_DSCK;
>> +             if (!cont && i == len - 1)
>> +                     tmp &= ~B53SPI_CDRAM_CONT;
>> +             tmp &= ~0x1;
>> +             /* Command Register File */
>> +             bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
>> +     }
>> +
>> +     /* Set queue pointers */
>> +     bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
>> +     bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
>> +
>> +     if (cont)
>> +             bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
>> +
>> +     /* Start SPI transfer */
>> +     tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
>> +     tmp |= B53SPI_MSPI_SPCR2_SPE;
>> +     if (cont)
>> +             tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
>> +     bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
>> +
>> +     /* Wait for SPI to finish */
>> +     bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
>
> This means we can only do unidirectonal transfers from the look of it -
> is that a limitation of the hardware (from a quick read it seems like it
> might be)?

Yeah, these transfers are really tricky. It took me a while to figure
out how to correctly read and write data. I spent hours writing some
opcodes, reading data and comparing it with what I expected to be on
the flash. Finally I did all this magic with "read_offset" and managed
to read/write data in a stable way.
OFC I don't have access to any Broadcom SPI controller specification,
it's not the way you can work with Broadcom hardware. If this hw can
handle transfers in some sane way (bidirectionally) I can't implement
it right now :(

>> +     /* Wait for SPI to finish */
>> +     bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
>
> No interrupts?  This will busy wait for the entire transfer which seems
> a bit much.

I'm afraid so. I found no reference to SPI interrupts.
Hauke: do you have any info about that?

> I'm also not seeing a set_cs() operation here.

I found no info about that, none of the registers seem to be
responsible for that. Is that OK for the driver to work without set_cs
handler/callback?

>> +     err = spi_register_master(master);
>> +     if (err) {
>
> devm_spi_register_master().

Will change that.

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 498 bytes --]

On Sun, Aug 17, 2014 at 05:28:13PM +0200, Rafał Miłecki wrote:
> On 17 August 2014 16:21, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:

> > I'm also not seeing a set_cs() operation here.

> I found no info about that, none of the registers seem to be
> responsible for that. Is that OK for the driver to work without set_cs
> handler/callback?

Well, it's going to break with quite a few client drivers but I guess
whoever runs into that problem can resolve it.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

[PATCH V2] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.

Signed-off-by: Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Since RFC: Add Signed-off-by
	   Update to compile on top of for-next
V2: Use wait timeout
    Describe bcm53xxspi_calc_timeout a bit
    Use devm_spi_register_master

Thanks Mark for your comments!
---
 drivers/spi/Kconfig       |   6 +
 drivers/spi/Makefile      |   1 +
 drivers/spi/spi-bcm53xx.c | 295 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/spi/spi-bcm53xx.h |  72 +++++++++++
 4 files changed, 374 insertions(+)
 create mode 100644 drivers/spi/spi-bcm53xx.c
 create mode 100644 drivers/spi/spi-bcm53xx.h

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 62e2242..b14b829 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -112,6 +112,12 @@ config SPI_AU1550
 	  If you say yes to this option, support will be included for the
 	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 
+config SPI_BCM53XX
+	tristate "Broadcom BCM53xx SPI controller"
+	depends on ARCH_BCM_5301X
+	help
+          Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
+
 config SPI_BCM63XX
 	tristate "Broadcom BCM63xx SPI controller"
 	depends on BCM63XX
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 762da07..78f24ca 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
 obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
+obj-$(CONFIG_SPI_BCM53XX)		+= spi-bcm53xx.o
 obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
 obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o
 obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
diff --git a/drivers/spi/spi-bcm53xx.c b/drivers/spi/spi-bcm53xx.c
new file mode 100644
index 0000000..ffc4461
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.c
@@ -0,0 +1,295 @@
+#define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/bcma/bcma.h>
+#include <linux/spi/spi.h>
+
+#include "spi-bcm53xx.h"
+
+#define BCM53XXSPI_MAX_SPI_BAUD	13500000	/* 216 MHz? */
+
+/* The longest observed required wait was 19 ms */
+#define BCM53XXSPI_SPE_TIMEOUT_MS	80
+
+struct bcm53xxspi {
+	struct bcma_device *core;
+	struct spi_master *master;
+
+	size_t read_offset;
+};
+
+static inline u32 bcm53xxspi_read(struct bcm53xxspi *b53spi, u16 offset)
+{
+	return bcma_read32(b53spi->core, offset);
+}
+
+static inline void bcm53xxspi_write(struct bcm53xxspi *b53spi, u16 offset,
+				    u32 value)
+{
+	bcma_write32(b53spi->core, offset, value);
+}
+
+static inline unsigned int bcm53xxspi_calc_timeout(size_t len)
+{
+	/* Do some magic calculation based on length and buad. Add 10% and 1. */
+	return (len * 9000 / BCM53XXSPI_MAX_SPI_BAUD * 110 / 100) + 1;
+}
+
+static int bcm53xxspi_wait(struct bcm53xxspi *b53spi, unsigned int timeout_ms)
+{
+	unsigned long deadline;
+	u32 tmp;
+
+	/* SPE bit has to be 0 before we read MSPI STATUS */
+	deadline = jiffies + BCM53XXSPI_SPE_TIMEOUT_MS * HZ / 1000;
+	do {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+		if (!(tmp & B53SPI_MSPI_SPCR2_SPE))
+			break;
+		udelay(5);
+	} while (!time_after_eq(jiffies, deadline));
+
+	if (tmp & B53SPI_MSPI_SPCR2_SPE)
+		goto spi_timeout;
+
+	/* Check status */
+	deadline = jiffies + timeout_ms * HZ / 1000;
+	do {
+		tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_MSPI_STATUS);
+		if (tmp & B53SPI_MSPI_MSPI_STATUS_SPIF) {
+			bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+			return 0;
+		}
+
+		cpu_relax();
+		udelay(100);
+	} while (!time_after_eq(jiffies, deadline));
+
+spi_timeout:
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_MSPI_STATUS, 0);
+
+	pr_err("Timeout waiting for SPI to be ready!\n");
+
+	return -EBUSY;
+}
+
+static void bcm53xxspi_buf_write(struct bcm53xxspi *b53spi, u8 *w_buf,
+				 size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < len; i++) {
+		/* Transmit Register File MSB */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_TXRAM + 4 * (i * 2),
+				 (unsigned int)w_buf[i]);
+	}
+
+	for (i = 0; i < len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP, len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	b53spi->read_offset = len;
+}
+
+static void bcm53xxspi_buf_read(struct bcm53xxspi *b53spi, u8 *r_buf,
+				size_t len, bool cont)
+{
+	u32 tmp;
+	int i;
+
+	for (i = 0; i < b53spi->read_offset + len; i++) {
+		tmp = B53SPI_CDRAM_CONT | B53SPI_CDRAM_PCS_DISABLE_ALL |
+		      B53SPI_CDRAM_PCS_DSCK;
+		if (!cont && i == b53spi->read_offset + len - 1)
+			tmp &= ~B53SPI_CDRAM_CONT;
+		tmp &= ~0x1;
+		/* Command Register File */
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_CDRAM + 4 * i, tmp);
+	}
+
+	/* Set queue pointers */
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_NEWQP, 0);
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_ENDQP,
+			 b53spi->read_offset + len - 1);
+
+	if (cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 1);
+
+	/* Start SPI transfer */
+	tmp = bcm53xxspi_read(b53spi, B53SPI_MSPI_SPCR2);
+	tmp |= B53SPI_MSPI_SPCR2_SPE;
+	if (cont)
+		tmp |= B53SPI_MSPI_SPCR2_CONT_AFTER_CMD;
+	bcm53xxspi_write(b53spi, B53SPI_MSPI_SPCR2, tmp);
+
+	/* Wait for SPI to finish */
+	bcm53xxspi_wait(b53spi, bcm53xxspi_calc_timeout(len));
+
+	if (!cont)
+		bcm53xxspi_write(b53spi, B53SPI_MSPI_WRITE_LOCK, 0);
+
+	for (i = 0; i < len; ++i) {
+		int offset = b53spi->read_offset + i;
+
+		/* Data stored in the transmit register file LSB */
+		r_buf[i] = (u8)bcm53xxspi_read(b53spi, B53SPI_MSPI_RXRAM + 4 * (1 + offset * 2));
+	}
+
+	b53spi->read_offset = 0;
+}
+
+static int bcm53xxspi_transfer_one(struct spi_master *master,
+				   struct spi_device *spi,
+				   struct spi_transfer *t)
+{
+	struct bcm53xxspi *b53spi = spi_master_get_devdata(master);
+	u8 *buf;
+	size_t left;
+
+	if (t->tx_buf) {
+		buf = (u8 *)t->tx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_write = min_t(size_t, 16, left);
+			bool cont = left - to_write > 0;
+
+			bcm53xxspi_buf_write(b53spi, buf, to_write, cont);
+			left -= to_write;
+			buf += to_write;
+		}
+	}
+
+	if (t->rx_buf) {
+		buf = (u8 *)t->rx_buf;
+		left = t->len;
+		while (left) {
+			size_t to_read = min_t(size_t, 16 - b53spi->read_offset,
+					       left);
+			bool cont = left - to_read > 0;
+
+			bcm53xxspi_buf_read(b53spi, buf, to_read, cont);
+			left -= to_read;
+			buf += to_read;
+		}
+	}
+
+	return 0;
+}
+
+/**************************************************
+ * BCMA
+ **************************************************/
+
+struct spi_board_info bcm53xx_info = {
+	.modalias	= "bcm53xxspiflash",
+};
+
+static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = {
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORETABLE_END
+};
+MODULE_DEVICE_TABLE(bcma, bcm53xxspi_bcma_tbl);
+
+static int bcm53xxspi_bcma_probe(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi;
+	struct spi_master *master;
+	int err;
+
+	if (core->bus->drv_cc.core->id.rev != 42) {
+		pr_err("SPI on SoC with unsupported ChipCommon rev\n");
+		return -ENOTSUPP;
+	}
+
+	master = spi_alloc_master(&core->dev, sizeof(*b53spi));
+	if (!master)
+		return -ENOMEM;
+
+	b53spi = spi_master_get_devdata(master);
+	b53spi->master = master;
+	b53spi->core = core;
+
+	master->transfer_one = bcm53xxspi_transfer_one;
+
+	bcma_set_drvdata(core, b53spi);
+
+	err = devm_spi_register_master(&core->dev, master);
+	if (err) {
+		spi_master_put(master);
+		bcma_set_drvdata(core, NULL);
+		goto out;
+	}
+
+	/* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */
+	spi_new_device(master, &bcm53xx_info);
+
+out:
+	return err;
+}
+
+static void bcm53xxspi_bcma_remove(struct bcma_device *core)
+{
+	struct bcm53xxspi *b53spi = bcma_get_drvdata(core);
+
+	spi_unregister_master(b53spi->master);
+}
+
+static struct bcma_driver bcm53xxspi_bcma_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= bcm53xxspi_bcma_tbl,
+	.probe		= bcm53xxspi_bcma_probe,
+	.remove		= bcm53xxspi_bcma_remove,
+};
+
+/**************************************************
+ * Init & exit
+ **************************************************/
+
+static int __init bcm53xxspi_module_init(void)
+{
+	int err = 0;
+
+	err = bcma_driver_register(&bcm53xxspi_bcma_driver);
+	if (err)
+		pr_err("Failed to register bcma driver: %d\n", err);
+
+	return err;
+}
+
+static void __exit bcm53xxspi_module_exit(void)
+{
+	bcma_driver_unregister(&bcm53xxspi_bcma_driver);
+}
+
+module_init(bcm53xxspi_module_init);
+module_exit(bcm53xxspi_module_exit);
diff --git a/drivers/spi/spi-bcm53xx.h b/drivers/spi/spi-bcm53xx.h
new file mode 100644
index 0000000..73575df
--- /dev/null
+++ b/drivers/spi/spi-bcm53xx.h
@@ -0,0 +1,72 @@
+#ifndef SPI_BCM53XX_H
+#define SPI_BCM53XX_H
+
+#define B53SPI_BSPI_REVISION_ID			0x000
+#define B53SPI_BSPI_SCRATCH			0x004
+#define B53SPI_BSPI_MAST_N_BOOT_CTRL		0x008
+#define B53SPI_BSPI_BUSY_STATUS			0x00c
+#define B53SPI_BSPI_INTR_STATUS			0x010
+#define B53SPI_BSPI_B0_STATUS			0x014
+#define B53SPI_BSPI_B0_CTRL			0x018
+#define B53SPI_BSPI_B1_STATUS			0x01c
+#define B53SPI_BSPI_B1_CTRL			0x020
+#define B53SPI_BSPI_STRAP_OVERRIDE_CTRL		0x024
+#define B53SPI_BSPI_FLEX_MODE_ENABLE		0x028
+#define B53SPI_BSPI_BITS_PER_CYCLE		0x02c
+#define B53SPI_BSPI_BITS_PER_PHASE		0x030
+#define B53SPI_BSPI_CMD_AND_MODE_BYTE		0x034
+#define B53SPI_BSPI_BSPI_FLASH_UPPER_ADDR_BYTE	0x038
+#define B53SPI_BSPI_BSPI_XOR_VALUE		0x03c
+#define B53SPI_BSPI_BSPI_XOR_ENABLE		0x040
+#define B53SPI_BSPI_BSPI_PIO_MODE_ENABLE	0x044
+#define B53SPI_BSPI_BSPI_PIO_IODIR		0x048
+#define B53SPI_BSPI_BSPI_PIO_DATA		0x04c
+
+/* RAF */
+#define B53SPI_RAF_START_ADDR			0x100
+#define B53SPI_RAF_NUM_WORDS			0x104
+#define B53SPI_RAF_CTRL				0x108
+#define B53SPI_RAF_FULLNESS			0x10c
+#define B53SPI_RAF_WATERMARK			0x110
+#define B53SPI_RAF_STATUS			0x114
+#define B53SPI_RAF_READ_DATA			0x118
+#define B53SPI_RAF_WORD_CNT			0x11c
+#define B53SPI_RAF_CURR_ADDR			0x120
+
+/* MSPI */
+#define B53SPI_MSPI_SPCR0_LSB			0x200
+#define B53SPI_MSPI_SPCR0_MSB			0x204
+#define B53SPI_MSPI_SPCR1_LSB			0x208
+#define B53SPI_MSPI_SPCR1_MSB			0x20c
+#define B53SPI_MSPI_NEWQP			0x210
+#define B53SPI_MSPI_ENDQP			0x214
+#define B53SPI_MSPI_SPCR2			0x218
+#define  B53SPI_MSPI_SPCR2_SPE			0x00000040
+#define  B53SPI_MSPI_SPCR2_CONT_AFTER_CMD	0x00000080
+#define B53SPI_MSPI_MSPI_STATUS			0x220
+#define  B53SPI_MSPI_MSPI_STATUS_SPIF		0x00000001
+#define B53SPI_MSPI_CPTQP			0x224
+#define B53SPI_MSPI_TXRAM			0x240 /* 32 registers, up to 0x2b8 */
+#define B53SPI_MSPI_RXRAM			0x2c0 /* 32 registers, up to 0x33c */
+#define B53SPI_MSPI_CDRAM			0x340 /* 16 registers, up to 0x37c */
+#define  B53SPI_CDRAM_PCS_PCS0			0x00000001
+#define  B53SPI_CDRAM_PCS_PCS1			0x00000002
+#define  B53SPI_CDRAM_PCS_PCS2			0x00000004
+#define  B53SPI_CDRAM_PCS_PCS3			0x00000008
+#define  B53SPI_CDRAM_PCS_DISABLE_ALL		0x0000000f
+#define  B53SPI_CDRAM_PCS_DSCK			0x00000010
+#define  B53SPI_CDRAM_BITSE			0x00000040
+#define  B53SPI_CDRAM_CONT			0x00000080
+#define B53SPI_MSPI_WRITE_LOCK			0x380
+#define B53SPI_MSPI_DISABLE_FLUSH_GEN		0x384
+
+/* Interrupt */
+#define B53SPI_INTR_RAF_LR_FULLNESS_REACHED	0x3a0
+#define B53SPI_INTR_RAF_LR_TRUNCATED		0x3a4
+#define B53SPI_INTR_RAF_LR_IMPATIENT		0x3a8
+#define B53SPI_INTR_RAF_LR_SESSION_DONE		0x3ac
+#define B53SPI_INTR_RAF_LR_OVERREAD		0x3b0
+#define B53SPI_INTR_MSPI_DONE			0x3b4
+#define B53SPI_INTR_MSPI_HALT_SET_TRANSACTION_DONE	0x3b8
+
+#endif /* SPI_BCM53XX_H */
-- 
1.8.4.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH V2] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 462 bytes --]

On Sun, Aug 17, 2014 at 06:33:38PM +0200, Rafał Miłecki wrote:
> Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
> devices). If board has a serial flash, it's connected over SPI and the
> bcma bus includes a SPI controller. Example log from such a board:
> bus0: Found chip with id 53010, rev 0x00 and package 0x02
> (...)
> bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

Applied, thanks.

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH V2] spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC

[Rafał Miłecki]

On 19 August 2014 18:31, Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
> On Sun, Aug 17, 2014 at 06:33:38PM +0200, Rafał Miłecki wrote:
>> Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
>> devices). If board has a serial flash, it's connected over SPI and the
>> bcma bus includes a SPI controller. Example log from such a board:
>> bus0: Found chip with id 53010, rev 0x00 and package 0x02
>> (...)
>> bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
>
> Applied, thanks.

Thank YOU! :)

-- 
Rafał
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html