* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10 8:55 ` klightspeed
0 siblings, 0 replies; 12+ messages in thread
From: klightspeed-aslSrjg9ejhWX4hkXwHRhw @ 2014-09-10 8:55 UTC (permalink / raw)
To: Jason Cooper, Ezequiel Garcia, Brian Norris, Russell King
Cc: Ben Peddell, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Gregory Clement,
devicetree-u79uwXL29TY76Z2rM5mHXA
The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
---
arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
+ /* Use Hardware BCH ECC */
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
partition@0 {
label = "u-boot";
reg = <0x0000000 0x180000>; /* 1.5MB */
--
1.8.5.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10 8:55 ` klightspeed
0 siblings, 0 replies; 12+ messages in thread
From: klightspeed at killerwolves.net @ 2014-09-10 8:55 UTC (permalink / raw)
To: linux-arm-kernel
The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
---
arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
+ /* Use Hardware BCH ECC */
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
partition at 0 {
label = "u-boot";
reg = <0x0000000 0x180000>; /* 1.5MB */
--
1.8.5.5
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10 8:55 ` klightspeed
0 siblings, 0 replies; 12+ messages in thread
From: klightspeed @ 2014-09-10 8:55 UTC (permalink / raw)
To: Jason Cooper, Ezequiel Garcia, Brian Norris, Russell King
Cc: Thomas Petazzoni, devicetree, Ben Peddell, Arnaud Ebalard,
linux-mtd, Gregory Clement, linux-arm-kernel
The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
---
arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
+ /* Use Hardware BCH ECC */
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
partition@0 {
label = "u-boot";
reg = <0x0000000 0x180000>; /* 1.5MB */
--
1.8.5.5
^ permalink raw reply related [flat|nested] 12+ messages in thread
[parent not found: <1410339341-3372-1-git-send-email-klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>]
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
2014-09-10 8:55 ` klightspeed
(?)
@ 2014-09-13 21:08 ` Jason Cooper
-1 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
To: klightspeed-aslSrjg9ejhWX4hkXwHRhw
Cc: Ezequiel Garcia, Brian Norris, Russell King,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Gregory Clement,
devicetree-u79uwXL29TY76Z2rM5mHXA
On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses
> Hamming ECC (strength = 1).
>
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
>
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
> ---
> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> 1 file changed, 4 insertions(+)
I've already applied this the mvebu/fixes:
500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
thx,
Jason.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-13 21:08 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses
> Hamming ECC (strength = 1).
>
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
>
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> ---
> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> 1 file changed, 4 insertions(+)
I've already applied this the mvebu/fixes:
500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
thx,
Jason.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-13 21:08 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
To: klightspeed
Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
linux-arm-kernel
On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses
> Hamming ECC (strength = 1).
>
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
>
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> ---
> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> 1 file changed, 4 insertions(+)
I've already applied this the mvebu/fixes:
500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
thx,
Jason.
^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <20140913210829.GI30828-u4khhh1J0LxI1Ri9qeTfzeTW4wlIGRCZ@public.gmane.org>]
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
2014-09-13 21:08 ` Jason Cooper
(?)
@ 2014-09-14 2:54 ` Ben Peddell
-1 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14 2:54 UTC (permalink / raw)
To: Jason Cooper
Cc: Ezequiel Garcia, Brian Norris, Russell King,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Gregory Clement,
devicetree-u79uwXL29TY76Z2rM5mHXA
On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
>> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
>> ---
>> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>> 1 file changed, 4 insertions(+)
>
> I've already applied this the mvebu/fixes:
>
> 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14 2:54 ` Ben Peddell
0 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14 2:54 UTC (permalink / raw)
To: linux-arm-kernel
On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
>> Tested-by: Arnaud Ebalard <arno@natisbad.org>
>> ---
>> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>> 1 file changed, 4 insertions(+)
>
> I've already applied this the mvebu/fixes:
>
> 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14 2:54 ` Ben Peddell
0 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14 2:54 UTC (permalink / raw)
To: Jason Cooper
Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
linux-arm-kernel
On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
>> Tested-by: Arnaud Ebalard <arno@natisbad.org>
>> ---
>> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>> 1 file changed, 4 insertions(+)
>
> I've already applied this the mvebu/fixes:
>
> 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <54150349.7050503-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>]
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
2014-09-14 2:54 ` Ben Peddell
(?)
@ 2014-09-14 4:18 ` Jason Cooper
-1 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14 4:18 UTC (permalink / raw)
To: Ben Peddell
Cc: Ezequiel Garcia, Brian Norris, Russell King,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Thomas Petazzoni, Gregory Clement,
devicetree-u79uwXL29TY76Z2rM5mHXA
On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> >> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
> >> ---
> >> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >> 1 file changed, 4 insertions(+)
> >
> > I've already applied this the mvebu/fixes:
> >
> > 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
>
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
>
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
Gah! You're right. Applied to mvebu/fixes and Cc'd the stable v3.14+
thx,
Jason.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14 4:18 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14 4:18 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> >> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> >> ---
> >> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >> 1 file changed, 4 insertions(+)
> >
> > I've already applied this the mvebu/fixes:
> >
> > 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
>
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
>
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
Gah! You're right. Applied to mvebu/fixes and Cc'd the stable v3.14+
thx,
Jason.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14 4:18 ` Jason Cooper
0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14 4:18 UTC (permalink / raw)
To: Ben Peddell
Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
linux-arm-kernel
On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> >> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> >> ---
> >> arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >> 1 file changed, 4 insertions(+)
> >
> > I've already applied this the mvebu/fixes:
> >
> > 500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
>
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
>
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
Gah! You're right. Applied to mvebu/fixes and Cc'd the stable v3.14+
thx,
Jason.
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2014-09-14 4:18 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-09-10 8:55 [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC klightspeed-aslSrjg9ejhWX4hkXwHRhw
2014-09-10 8:55 ` klightspeed at killerwolves.net
2014-09-10 8:55 ` klightspeed
[not found] ` <1410339341-3372-1-git-send-email-klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-09-13 21:08 ` Jason Cooper
2014-09-13 21:08 ` Jason Cooper
2014-09-13 21:08 ` Jason Cooper
[not found] ` <20140913210829.GI30828-u4khhh1J0LxI1Ri9qeTfzeTW4wlIGRCZ@public.gmane.org>
2014-09-14 2:54 ` Ben Peddell
2014-09-14 2:54 ` Ben Peddell
2014-09-14 2:54 ` Ben Peddell
[not found] ` <54150349.7050503-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-09-14 4:18 ` Jason Cooper
2014-09-14 4:18 ` Jason Cooper
2014-09-14 4:18 ` Jason Cooper
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.