* [U-Boot] Upstream uboot and Arndale 5250 support
@ 2014-10-07 12:58 Paolo Pisati
2014-10-07 14:34 ` Guillaume Gardet
0 siblings, 1 reply; 6+ messages in thread
From: Paolo Pisati @ 2014-10-07 12:58 UTC (permalink / raw)
To: u-boot
Hi,
i've been trying to update the u-boot on my board (sd booting), from the Linaro
one (2012.10) to a v2014.X, but so far had no luck:
make arndale_config
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make
...
dd if=arndale-bl1.bin of=/dev/sdc bs=512 skip=1
dd if=arndale-spl.bin of=/dev/sdc bs=512 skip=17
dd if=./u-boot-dtb.bin of=/dev/sdc bs=512 skip=49
...
u-boot 3.10rc3 (same happens with v2014.07 or 2014.04):
U-Boot 2014.10-rc3 (Oct 07 2014 - 13:26:48) for ARNDALE
CPU: Exynos5250 at 1000MHz
Board: Arndale
I2C: i2c_init: failed to init bus 0 for speed = 100000
ready
DRAM: 2 GiB
trace: copying 00086db4 bytes of early data from 50000000 to beff0000
trace: enabled
WARNING: Caches not enabled
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
dwmci_send_cmd: DATA ERROR!
i2c_init: failed to init bus 0 for speed = 100000
In: serial
Out: serial
Err: serial
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
ARNDALE # printenv
baudrate=115200
bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug earlyprintk
bootcmd=run bootcmd_ubuntu
bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
bootdelay=3
fdt_addr_r=0x41000000
filesize=5b9902
kernel_addr_r=0x40007000
loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
ramdisk_addr_r=0x42000000
stderr=serial
stdin=serial
stdout=serial
Environment size: 589/16380 bytes
ARNDALE # run loadk
6002946 bytes read in 1117 ms (5.1 MiB/s)
ARNDALE # bootm ${kernel_addr_r}
## Booting kernel from Legacy Image at 40007000 ...
Image Name: kernel 3.16.0-20-generic
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6002882 Bytes = 5.7 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...(fake run for tracing)
Starting kernel ...
[stuck here]
here for a more complete log:
http://pastebin.ubuntu.com/8514108/plain/
Any idea what's going wrong? Did you try this board lately?
It's a kernel with the DTB concatenated (and it works fine with Linaro 2012
uboot), but the same happens if i explicitely pass the dtb:
U-Boot 2014.07 (Sep 30 2014 - 15:26:03) for ARNDALE
CPU: Exynos5250 at 1000MHz
Board: Arndale
I2C: i2c_init: failed to init bus 0 for speed = 100000
ready
DRAM: 2 GiB
trace: copying 00085818 bytes of early data from 50000000 to beff0000
trace: enabled
WARNING: Caches not enabled
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
i2c_init: failed to init bus 0 for speed = 100000
In: serial
Out: serial
Err: serial
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
ARNDALE # printenv
baudrate=115200
bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug earlyprintk
bootcmd=run bootcmd_ubuntu
bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
bootdelay=3
fdt_addr_r=0x41000000
filesize=5b9902
kernel_addr_r=0x40007000
loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
ramdisk_addr_r=0x42000000
stderr=serial
stdin=serial
stdout=serial
Environment size: 589/16380 bytes
ARNDALE # run loadk
6002946 bytes read in 1114 ms (5.1 MiB/s)
ARNDALE # run loadf
35450 bytes read in 34 ms (1017.6 KiB/s)
ARNDALE # bootm ${kernel_addr_r} - ${fdt_addr_r}
## Booting kernel from Legacy Image at 40007000 ...
Image Name: kernel 3.16.0-20-generic
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6002882 Bytes = 5.7 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 41000000
Booting using the fdt blob at 0x41000000
Loading Kernel Image ... OK
Loading Device Tree to 4fff4000, end 4ffffa79 ... OK
Starting kernel ...(fake run for tracing)
Starting kernel ...
[stuck again]
(please cc: me as i'm off list)
--
bye,
p.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] Upstream uboot and Arndale 5250 support
2014-10-07 12:58 [U-Boot] Upstream uboot and Arndale 5250 support Paolo Pisati
@ 2014-10-07 14:34 ` Guillaume Gardet
2014-10-07 15:02 ` Paolo Pisati
0 siblings, 1 reply; 6+ messages in thread
From: Guillaume Gardet @ 2014-10-07 14:34 UTC (permalink / raw)
To: u-boot
Hi,
Le 07/10/2014 14:58, Paolo Pisati a ?crit :
> Hi,
>
> i've been trying to update the u-boot on my board (sd booting), from the Linaro
> one (2012.10) to a v2014.X, but so far had no luck:
>
> make arndale_config
> export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
> make
>
> ...
>
> dd if=arndale-bl1.bin of=/dev/sdc bs=512 skip=1
> dd if=arndale-spl.bin of=/dev/sdc bs=512 skip=17
> dd if=./u-boot-dtb.bin of=/dev/sdc bs=512 skip=49
>
> ...
>
> u-boot 3.10rc3 (same happens with v2014.07 or 2014.04):
>
> U-Boot 2014.10-rc3 (Oct 07 2014 - 13:26:48) for ARNDALE
>
> CPU: Exynos5250 at 1000MHz
>
> Board: Arndale
> I2C: i2c_init: failed to init bus 0 for speed = 100000
> ready
> DRAM: 2 GiB
> trace: copying 00086db4 bytes of early data from 50000000 to beff0000
> trace: enabled
> WARNING: Caches not enabled
> MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
> dwmci_send_cmd: DATA ERROR!
> i2c_init: failed to init bus 0 for speed = 100000
> In: serial
> Out: serial
> Err: serial
> Net: Net Initialization Skipped
> No ethernet found.
> Hit any key to stop autoboot: 0
> ARNDALE # printenv
> baudrate=115200
> bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug earlyprintk
> bootcmd=run bootcmd_ubuntu
> bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
> bootdelay=3
> fdt_addr_r=0x41000000
> filesize=5b9902
> kernel_addr_r=0x40007000
> loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
> loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
> loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
> ramdisk_addr_r=0x42000000
> stderr=serial
> stdin=serial
> stdout=serial
>
> Environment size: 589/16380 bytes
> ARNDALE # run loadk
> 6002946 bytes read in 1117 ms (5.1 MiB/s)
> ARNDALE # bootm ${kernel_addr_r}
> ## Booting kernel from Legacy Image at 40007000 ...
> Image Name: kernel 3.16.0-20-generic
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 6002882 Bytes = 5.7 MiB
> Load Address: 40008000
> Entry Point: 40008000
> Verifying Checksum ... OK
> Loading Kernel Image ... OK
>
> Starting kernel ...(fake run for tracing)
>
> Starting kernel ...
>
> [stuck here]
I faced this problem some times ago. Try to modify kernel, initrd and fdt addresses.
Guillaume
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] Upstream uboot and Arndale 5250 support
2014-10-07 14:34 ` Guillaume Gardet
@ 2014-10-07 15:02 ` Paolo Pisati
2014-10-08 8:00 ` Guillaume Gardet
0 siblings, 1 reply; 6+ messages in thread
From: Paolo Pisati @ 2014-10-07 15:02 UTC (permalink / raw)
To: u-boot
those are the addresses suggested by u-boot and yes, i already tried
moving stuff around but it didn't fix it: what's the working config
with your board? u-boot version?
On Tue, Oct 7, 2014 at 4:34 PM, Guillaume Gardet
<guillaume.gardet@free.fr> wrote:
> Hi,
>
> Le 07/10/2014 14:58, Paolo Pisati a ?crit :
>
>> Hi,
>>
>> i've been trying to update the u-boot on my board (sd booting), from the
>> Linaro
>> one (2012.10) to a v2014.X, but so far had no luck:
>>
>> make arndale_config
>> export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
>> make
>>
>> ...
>>
>> dd if=arndale-bl1.bin of=/dev/sdc bs=512 skip=1
>> dd if=arndale-spl.bin of=/dev/sdc bs=512 skip=17
>> dd if=./u-boot-dtb.bin of=/dev/sdc bs=512 skip=49
>>
>> ...
>>
>> u-boot 3.10rc3 (same happens with v2014.07 or 2014.04):
>>
>> U-Boot 2014.10-rc3 (Oct 07 2014 - 13:26:48) for ARNDALE
>>
>> CPU: Exynos5250 at 1000MHz
>>
>> Board: Arndale
>> I2C: i2c_init: failed to init bus 0 for speed = 100000
>> ready
>> DRAM: 2 GiB
>> trace: copying 00086db4 bytes of early data from 50000000 to beff0000
>> trace: enabled
>> WARNING: Caches not enabled
>> MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
>> dwmci_send_cmd: DATA ERROR!
>> i2c_init: failed to init bus 0 for speed = 100000
>> In: serial
>> Out: serial
>> Err: serial
>> Net: Net Initialization Skipped
>> No ethernet found.
>> Hit any key to stop autoboot: 0
>> ARNDALE # printenv
>> baudrate=115200
>> bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug
>> earlyprintk
>> bootcmd=run bootcmd_ubuntu
>> bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r}
>> ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
>> bootdelay=3
>> fdt_addr_r=0x41000000
>> filesize=5b9902
>> kernel_addr_r=0x40007000
>> loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
>> loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
>> loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
>> ramdisk_addr_r=0x42000000
>> stderr=serial
>> stdin=serial
>> stdout=serial
>>
>> Environment size: 589/16380 bytes
>> ARNDALE # run loadk
>> 6002946 bytes read in 1117 ms (5.1 MiB/s)
>> ARNDALE # bootm ${kernel_addr_r}
>> ## Booting kernel from Legacy Image at 40007000 ...
>> Image Name: kernel 3.16.0-20-generic
>> Image Type: ARM Linux Kernel Image (uncompressed)
>> Data Size: 6002882 Bytes = 5.7 MiB
>> Load Address: 40008000
>> Entry Point: 40008000
>> Verifying Checksum ... OK
>> Loading Kernel Image ... OK
>>
>> Starting kernel ...(fake run for tracing)
>>
>> Starting kernel ...
>>
>> [stuck here]
>
>
> I faced this problem some times ago. Try to modify kernel, initrd and fdt
> addresses.
>
>
> Guillaume
>
--
bye,
p.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] Upstream uboot and Arndale 5250 support
2014-10-07 15:02 ` Paolo Pisati
@ 2014-10-08 8:00 ` Guillaume Gardet
2014-10-08 10:16 ` Paolo Pisati
0 siblings, 1 reply; 6+ messages in thread
From: Guillaume Gardet @ 2014-10-08 8:00 UTC (permalink / raw)
To: u-boot
I used the following values with 2014.10-rc2:
kerneladdr=0x44000000
ramdiskaddr=0x45000000
fdtaddr=0x4c000000
But I used a zImage. If you use a uImage, you need to modify the kernel load addr.
Guillaume
Le 07/10/2014 17:02, Paolo Pisati a ?crit :
> those are the addresses suggested by u-boot and yes, i already tried
> moving stuff around but it didn't fix it: what's the working config
> with your board? u-boot version?
>
> On Tue, Oct 7, 2014 at 4:34 PM, Guillaume Gardet
> <guillaume.gardet@free.fr> wrote:
>> Hi,
>>
>> Le 07/10/2014 14:58, Paolo Pisati a ?crit :
>>
>>> Hi,
>>>
>>> i've been trying to update the u-boot on my board (sd booting), from the
>>> Linaro
>>> one (2012.10) to a v2014.X, but so far had no luck:
>>>
>>> make arndale_config
>>> export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
>>> make
>>>
>>> ...
>>>
>>> dd if=arndale-bl1.bin of=/dev/sdc bs=512 skip=1
>>> dd if=arndale-spl.bin of=/dev/sdc bs=512 skip=17
>>> dd if=./u-boot-dtb.bin of=/dev/sdc bs=512 skip=49
>>>
>>> ...
>>>
>>> u-boot 3.10rc3 (same happens with v2014.07 or 2014.04):
>>>
>>> U-Boot 2014.10-rc3 (Oct 07 2014 - 13:26:48) for ARNDALE
>>>
>>> CPU: Exynos5250 at 1000MHz
>>>
>>> Board: Arndale
>>> I2C: i2c_init: failed to init bus 0 for speed = 100000
>>> ready
>>> DRAM: 2 GiB
>>> trace: copying 00086db4 bytes of early data from 50000000 to beff0000
>>> trace: enabled
>>> WARNING: Caches not enabled
>>> MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
>>> dwmci_send_cmd: DATA ERROR!
>>> i2c_init: failed to init bus 0 for speed = 100000
>>> In: serial
>>> Out: serial
>>> Err: serial
>>> Net: Net Initialization Skipped
>>> No ethernet found.
>>> Hit any key to stop autoboot: 0
>>> ARNDALE # printenv
>>> baudrate=115200
>>> bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug
>>> earlyprintk
>>> bootcmd=run bootcmd_ubuntu
>>> bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r}
>>> ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
>>> bootdelay=3
>>> fdt_addr_r=0x41000000
>>> filesize=5b9902
>>> kernel_addr_r=0x40007000
>>> loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
>>> loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
>>> loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
>>> ramdisk_addr_r=0x42000000
>>> stderr=serial
>>> stdin=serial
>>> stdout=serial
>>>
>>> Environment size: 589/16380 bytes
>>> ARNDALE # run loadk
>>> 6002946 bytes read in 1117 ms (5.1 MiB/s)
>>> ARNDALE # bootm ${kernel_addr_r}
>>> ## Booting kernel from Legacy Image at 40007000 ...
>>> Image Name: kernel 3.16.0-20-generic
>>> Image Type: ARM Linux Kernel Image (uncompressed)
>>> Data Size: 6002882 Bytes = 5.7 MiB
>>> Load Address: 40008000
>>> Entry Point: 40008000
>>> Verifying Checksum ... OK
>>> Loading Kernel Image ... OK
>>>
>>> Starting kernel ...(fake run for tracing)
>>>
>>> Starting kernel ...
>>>
>>> [stuck here]
>>
>> I faced this problem some times ago. Try to modify kernel, initrd and fdt
>> addresses.
>>
>>
>> Guillaume
>>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] Upstream uboot and Arndale 5250 support
2014-10-08 8:00 ` Guillaume Gardet
@ 2014-10-08 10:16 ` Paolo Pisati
2014-10-08 13:13 ` Guillaume Gardet
0 siblings, 1 reply; 6+ messages in thread
From: Paolo Pisati @ 2014-10-08 10:16 UTC (permalink / raw)
To: u-boot
that's weird, because i don't have bootz:
U-Boot 2014.10-rc3 (Oct 08 2014 - 11:34:33) for ARNDALE
CPU: Exynos5250 at 1000MHz
Board: Arndale
I2C: i2c_init: failed to init bus 0 for speed = 100000
ready
DRAM: 2 GiB
trace: copying 00086db4 bytes of early data from 50000000 to beff0000
trace: enabled
WARNING: Caches not enabled
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
dwmci_send_cmd: DATA ERROR!
i2c_init: failed to init bus 0 for speed = 100000
In: serial
Out: serial
Err: serial
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
ARNDALE # help bootz
Unknown command 'bootz' - try 'help' without arguments for list of all
known commands
ARNDALE #
are you using a patched u-boot?
i'm using the default arndale_defconfig.
anyhow, can i have your full working config?
i'm starting to feel i'm chasing ghosts here.
On Wed, Oct 8, 2014 at 10:00 AM, Guillaume Gardet
<guillaume.gardet@free.fr> wrote:
> I used the following values with 2014.10-rc2:
> kerneladdr=0x44000000
> ramdiskaddr=0x45000000
> fdtaddr=0x4c000000
>
> But I used a zImage. If you use a uImage, you need to modify the kernel load
> addr.
>
> Guillaume
>
>
> Le 07/10/2014 17:02, Paolo Pisati a ?crit :
>
>> those are the addresses suggested by u-boot and yes, i already tried
>> moving stuff around but it didn't fix it: what's the working config
>> with your board? u-boot version?
>>
>> On Tue, Oct 7, 2014 at 4:34 PM, Guillaume Gardet
>> <guillaume.gardet@free.fr> wrote:
>>>
>>> Hi,
>>>
>>> Le 07/10/2014 14:58, Paolo Pisati a ?crit :
>>>
>>>> Hi,
>>>>
>>>> i've been trying to update the u-boot on my board (sd booting), from the
>>>> Linaro
>>>> one (2012.10) to a v2014.X, but so far had no luck:
>>>>
>>>> make arndale_config
>>>> export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
>>>> make
>>>>
>>>> ...
>>>>
>>>> dd if=arndale-bl1.bin of=/dev/sdc bs=512 skip=1
>>>> dd if=arndale-spl.bin of=/dev/sdc bs=512 skip=17
>>>> dd if=./u-boot-dtb.bin of=/dev/sdc bs=512 skip=49
>>>>
>>>> ...
>>>>
>>>> u-boot 3.10rc3 (same happens with v2014.07 or 2014.04):
>>>>
>>>> U-Boot 2014.10-rc3 (Oct 07 2014 - 13:26:48) for ARNDALE
>>>>
>>>> CPU: Exynos5250 at 1000MHz
>>>>
>>>> Board: Arndale
>>>> I2C: i2c_init: failed to init bus 0 for speed = 100000
>>>> ready
>>>> DRAM: 2 GiB
>>>> trace: copying 00086db4 bytes of early data from 50000000 to beff0000
>>>> trace: enabled
>>>> WARNING: Caches not enabled
>>>> MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
>>>> dwmci_send_cmd: DATA ERROR!
>>>> i2c_init: failed to init bus 0 for speed = 100000
>>>> In: serial
>>>> Out: serial
>>>> Err: serial
>>>> Net: Net Initialization Skipped
>>>> No ethernet found.
>>>> Hit any key to stop autoboot: 0
>>>> ARNDALE # printenv
>>>> baudrate=115200
>>>> bootargs=console=ttySAC2,115200n8 root=/dev/mmcblk1p1 rw rootwait debug
>>>> earlyprintk
>>>> bootcmd=run bootcmd_ubuntu
>>>> bootcmd_ubuntu=run loadk; run loadf; run loadr; bootm ${kernel_addr_r}
>>>> ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
>>>> bootdelay=3
>>>> fdt_addr_r=0x41000000
>>>> filesize=5b9902
>>>> kernel_addr_r=0x40007000
>>>> loadf=ext2load mmc 1:1 ${fdt_addr_r} /boot/exynos5250-arndale.dtb
>>>> loadk=ext2load mmc 1:1 ${kernel_addr_r} /boot/uImage
>>>> loadr=ext2load mmc 1:1 ${ramdisk_addr_r} /boot/uInitrd
>>>> ramdisk_addr_r=0x42000000
>>>> stderr=serial
>>>> stdin=serial
>>>> stdout=serial
>>>>
>>>> Environment size: 589/16380 bytes
>>>> ARNDALE # run loadk
>>>> 6002946 bytes read in 1117 ms (5.1 MiB/s)
>>>> ARNDALE # bootm ${kernel_addr_r}
>>>> ## Booting kernel from Legacy Image at 40007000 ...
>>>> Image Name: kernel 3.16.0-20-generic
>>>> Image Type: ARM Linux Kernel Image (uncompressed)
>>>> Data Size: 6002882 Bytes = 5.7 MiB
>>>> Load Address: 40008000
>>>> Entry Point: 40008000
>>>> Verifying Checksum ... OK
>>>> Loading Kernel Image ... OK
>>>>
>>>> Starting kernel ...(fake run for tracing)
>>>>
>>>> Starting kernel ...
>>>>
>>>> [stuck here]
>>>
>>>
>>> I faced this problem some times ago. Try to modify kernel, initrd and fdt
>>> addresses.
>>>
>>>
>>> Guillaume
>>>
>>
>>
>
--
bye,
p.
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] Upstream uboot and Arndale 5250 support
2014-10-08 10:16 ` Paolo Pisati
@ 2014-10-08 13:13 ` Guillaume Gardet
0 siblings, 0 replies; 6+ messages in thread
From: Guillaume Gardet @ 2014-10-08 13:13 UTC (permalink / raw)
To: u-boot
Le 08/10/2014 12:16, Paolo Pisati a ?crit :
> that's weird, because i don't have bootz:
>
>
> are you using a patched u-boot?
>
> i'm using the default arndale_defconfig.
>
> anyhow, can i have your full working config?
> i'm starting to feel i'm chasing ghosts here.
I used this patch for -rc2 (which will not apply on -rc3 because of changes on arndale config between -rc2 and -rc3):
https://patchwork.ozlabs.org/patch/391247/raw/
with arndale_defconfig.
Then, I used a bootscript which defined and used the values I gave you:
kerneladdr=0x44000000
ramdiskaddr=0x45000000
fdtaddr=0x4c000000
But you can define those values manually, of courses.
Hope it will help you.
Guillaume
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-10-08 13:13 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-10-07 12:58 [U-Boot] Upstream uboot and Arndale 5250 support Paolo Pisati
2014-10-07 14:34 ` Guillaume Gardet
2014-10-07 15:02 ` Paolo Pisati
2014-10-08 8:00 ` Guillaume Gardet
2014-10-08 10:16 ` Paolo Pisati
2014-10-08 13:13 ` Guillaume Gardet
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.