From: Lina Iyer <lina.iyer@linaro.org> To: Kevin Hilman <khilman@kernel.org> Cc: daniel.lezcano@linaro.org, sboyd@codeaurora.org, galak@codeaurora.org, linux-arm-msm@vger.kernel.org, linux-pm@vger.kernel.org, linux-arm-kernel@lists.infradead.org, lorenzo.pieralisi@arm.com, msivasub@codeaurora.org, devicetree@vger.kernel.org Subject: Re: [PATCH v14 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Date: Wed, 17 Dec 2014 11:25:09 -0700 [thread overview] Message-ID: <20141217182509.GA1913@linaro.org> (raw) In-Reply-To: <7hegryb0te.fsf@deeprootsystems.com> On Wed, Dec 17 2014 at 11:14 -0700, Kevin Hilman wrote: >Lina Iyer <lina.iyer@linaro.org> writes: > >> Dependent patchsets - >> https://lkml.org/lkml/2014/8/4/767 >> http://www.spinics.net/lists/linux-arm-msm/msg10799.html >> http://www.spinics.net/lists/linux-arm-msm/msg10795.html >> >> Changes since v13: >> - Return values for idle states propagated back to the cpuidle driver. >> - Remove static bool cpuidle_drv_init. >> - Register cpuidle driver and cpuidle device separately. >> - cpuidle device registered only when the SPM for the cpu is probed. >> - Initialization changes to ensure dynamic cpuidle devices are registered only >> after the cpuidle driver is registered. >> - Removed wmb, replaced with a poll loop to ensure that the SPM registers are >> written before executing wfi. >> - Added spm_register_write_sync() for write guarantees. >> - Removed irrelevant return value for spm_set_low_power_mode(). >> - Added comments, updated module description. >> - Removed Reviewed-by and Acked-by on the spm and cpuidle-qcom patches. > >I think this series should also include updates to qcom_defconfig that >enable QCOM_PM and the cpuidle driver. > >Then it will be enabled by default and get more broad testing. Sure. I will be enabling them in the next revision of the series. > >Kevin
WARNING: multiple messages have this Message-ID (diff)
From: lina.iyer@linaro.org (Lina Iyer) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v14 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Date: Wed, 17 Dec 2014 11:25:09 -0700 [thread overview] Message-ID: <20141217182509.GA1913@linaro.org> (raw) In-Reply-To: <7hegryb0te.fsf@deeprootsystems.com> On Wed, Dec 17 2014 at 11:14 -0700, Kevin Hilman wrote: >Lina Iyer <lina.iyer@linaro.org> writes: > >> Dependent patchsets - >> https://lkml.org/lkml/2014/8/4/767 >> http://www.spinics.net/lists/linux-arm-msm/msg10799.html >> http://www.spinics.net/lists/linux-arm-msm/msg10795.html >> >> Changes since v13: >> - Return values for idle states propagated back to the cpuidle driver. >> - Remove static bool cpuidle_drv_init. >> - Register cpuidle driver and cpuidle device separately. >> - cpuidle device registered only when the SPM for the cpu is probed. >> - Initialization changes to ensure dynamic cpuidle devices are registered only >> after the cpuidle driver is registered. >> - Removed wmb, replaced with a poll loop to ensure that the SPM registers are >> written before executing wfi. >> - Added spm_register_write_sync() for write guarantees. >> - Removed irrelevant return value for spm_set_low_power_mode(). >> - Added comments, updated module description. >> - Removed Reviewed-by and Acked-by on the spm and cpuidle-qcom patches. > >I think this series should also include updates to qcom_defconfig that >enable QCOM_PM and the cpuidle driver. > >Then it will be enabled by default and get more broad testing. Sure. I will be enabling them in the next revision of the series. > >Kevin
next prev parent reply other threads:[~2014-12-17 18:25 UTC|newest] Thread overview: 62+ messages / expand[flat|nested] mbox.gz Atom feed top 2014-12-02 17:39 [PATCH v14 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 01/10] qcom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 03/10] qcom: spm: Add Subsystem Power Manager driver Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 23:05 ` Lina Iyer 2014-12-02 23:05 ` Lina Iyer 2014-12-03 9:11 ` Daniel Lezcano 2014-12-03 9:11 ` Daniel Lezcano 2014-12-03 14:31 ` Lina Iyer 2014-12-03 14:31 ` Lina Iyer 2014-12-03 14:55 ` Lina Iyer 2014-12-03 14:55 ` Lina Iyer 2014-12-03 20:35 ` Arnd Bergmann 2014-12-03 20:35 ` Arnd Bergmann 2014-12-04 8:52 ` Daniel Lezcano 2014-12-04 8:52 ` Daniel Lezcano 2014-12-04 9:01 ` Arnd Bergmann 2014-12-04 9:01 ` Arnd Bergmann 2014-12-04 16:28 ` Lina Iyer 2014-12-04 16:28 ` Lina Iyer 2014-12-04 18:20 ` Arnd Bergmann 2014-12-04 18:20 ` Arnd Bergmann 2014-12-05 15:45 ` Lina Iyer 2014-12-05 15:45 ` Lina Iyer 2014-12-16 14:39 ` Arnd Bergmann 2014-12-16 14:39 ` Arnd Bergmann 2014-12-16 14:12 ` Daniel Lezcano 2014-12-16 14:12 ` Daniel Lezcano 2014-12-16 14:38 ` Arnd Bergmann 2014-12-16 14:38 ` Arnd Bergmann 2014-12-16 19:18 ` Stephen Boyd 2014-12-16 19:18 ` Stephen Boyd 2014-12-16 19:44 ` Arnd Bergmann 2014-12-16 19:44 ` Arnd Bergmann 2014-12-17 15:22 ` Lina Iyer 2014-12-17 15:22 ` Lina Iyer 2014-12-17 13:15 ` Daniel Lezcano 2014-12-17 13:15 ` Daniel Lezcano 2014-12-17 14:04 ` Lorenzo Pieralisi 2014-12-17 14:04 ` Lorenzo Pieralisi 2014-12-02 17:39 ` [PATCH v14 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 05/10] arm: dts: qcom: Add power-controller device node for 8084 " Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 06/10] arm: dts: qcom: Update power-controller device node for 8064 " Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 08/10] arm: dts: qcom: Add idle states device nodes for 8074 Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 09/10] arm: dts: qcom: Add idle states device nodes for 8084 Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-02 17:39 ` [PATCH v14 10/10] arm: dts: qcom: Add idle state device nodes for 8064 Lina Iyer 2014-12-02 17:39 ` Lina Iyer 2014-12-17 18:14 ` [PATCH v14 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Kevin Hilman 2014-12-17 18:14 ` Kevin Hilman 2014-12-17 18:25 ` Lina Iyer [this message] 2014-12-17 18:25 ` Lina Iyer
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20141217182509.GA1913@linaro.org \ --to=lina.iyer@linaro.org \ --cc=daniel.lezcano@linaro.org \ --cc=devicetree@vger.kernel.org \ --cc=galak@codeaurora.org \ --cc=khilman@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-arm-msm@vger.kernel.org \ --cc=linux-pm@vger.kernel.org \ --cc=lorenzo.pieralisi@arm.com \ --cc=msivasub@codeaurora.org \ --cc=sboyd@codeaurora.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.