* [PATCH v5 0/6] imx25 adc and touchscreen driver
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
Hi,
This series adds a driver for the Freescale i.MX25 SoC internal ADC unit which
is used for touchscreen and ADC. The driver consists of three parts, the MFD
driver which handles interrupts and some central configuration registers, the
ADC driver and the touchscreen driver.
The last couple of versions of this series were pushed by Denis, thanks. Now I
tried to work on the comments of the last version v4 of last year.
v5 has a lot of smaller changes, listed below. I also fixed the touchscreen
driver to reduce the number of interrupts. The drivers first version was
designed to start a new conversion whenever we got a conversion done or a
pendown was detected. This lead to a lot of interrupts. Instead we use the
ability of the hardware unit to repeat a conversion queue automatically with a
repeat wait timer. This is done in hardware and configured only once in
software to a constant value.
Best regards,
Markus
Changes in v5:
- Removed module owner assingments from all drivers
- Added missing kconfig dependencies
- Separated DT binding documentation
- Fixed locking for the gcq driver
- Fixed a lot of style issues with the newer checkpatch tool, e.g. alignment
of breaked lines
Denis Carikli (2):
ARM: dts: imx25: Add TSC and ADC support
ARM: imx_v4_v5_defconfig: Add I.MX25 Touchscreen controller and ADC
support.
Markus Pargmann (4):
mfd: fsl imx25 Touchscreen ADC driver
ARM: dt: Binding documentation for imx25 ADC/TSC
iio: adc: fsl,imx25-gcq driver
input: touchscreen: imx25 tcq driver
.../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 ++
.../bindings/input/touchscreen/fsl-mx25-tcq.txt | 29 +
.../devicetree/bindings/mfd/fsl-imx25-tsadc.txt | 46 ++
arch/arm/boot/dts/imx25.dtsi | 30 +-
arch/arm/configs/imx_v4_v5_defconfig | 4 +
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++
drivers/input/touchscreen/Kconfig | 6 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/fsl-imx25-tcq.c | 587 +++++++++++++++++++++
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 2 +
drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++
include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
include/linux/mfd/imx25-tsadc.h | 140 +++++
16 files changed, 1458 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
create mode 100644 Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c
create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
create mode 100644 include/linux/mfd/imx25-tsadc.h
--
2.1.4
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 0/6] imx25 adc and touchscreen driver
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
This series adds a driver for the Freescale i.MX25 SoC internal ADC unit which
is used for touchscreen and ADC. The driver consists of three parts, the MFD
driver which handles interrupts and some central configuration registers, the
ADC driver and the touchscreen driver.
The last couple of versions of this series were pushed by Denis, thanks. Now I
tried to work on the comments of the last version v4 of last year.
v5 has a lot of smaller changes, listed below. I also fixed the touchscreen
driver to reduce the number of interrupts. The drivers first version was
designed to start a new conversion whenever we got a conversion done or a
pendown was detected. This lead to a lot of interrupts. Instead we use the
ability of the hardware unit to repeat a conversion queue automatically with a
repeat wait timer. This is done in hardware and configured only once in
software to a constant value.
Best regards,
Markus
Changes in v5:
- Removed module owner assingments from all drivers
- Added missing kconfig dependencies
- Separated DT binding documentation
- Fixed locking for the gcq driver
- Fixed a lot of style issues with the newer checkpatch tool, e.g. alignment
of breaked lines
Denis Carikli (2):
ARM: dts: imx25: Add TSC and ADC support
ARM: imx_v4_v5_defconfig: Add I.MX25 Touchscreen controller and ADC
support.
Markus Pargmann (4):
mfd: fsl imx25 Touchscreen ADC driver
ARM: dt: Binding documentation for imx25 ADC/TSC
iio: adc: fsl,imx25-gcq driver
input: touchscreen: imx25 tcq driver
.../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 ++
.../bindings/input/touchscreen/fsl-mx25-tcq.txt | 29 +
.../devicetree/bindings/mfd/fsl-imx25-tsadc.txt | 46 ++
arch/arm/boot/dts/imx25.dtsi | 30 +-
arch/arm/configs/imx_v4_v5_defconfig | 4 +
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++
drivers/input/touchscreen/Kconfig | 6 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/fsl-imx25-tcq.c | 587 +++++++++++++++++++++
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 2 +
drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++
include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
include/linux/mfd/imx25-tsadc.h | 140 +++++
16 files changed, 1458 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
create mode 100644 Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c
create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
create mode 100644 include/linux/mfd/imx25-tsadc.h
--
2.1.4
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.
This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
---
Notes:
Changes in v5:
- Remove ifdef CONFIG_OF as this driver is only for DT usage
- Remove module owner
- Add Kconfig dependencies ARCH_MX25 and OF
@Jonathan Cameron:
I left your acked-by on the patch as these were small changes. If it should be
removed, please say so. Thanks
drivers/mfd/Kconfig | 10 +++
drivers/mfd/Makefile | 2 +
drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/imx25-tsadc.h | 140 +++++++++++++++++++++++++++++++++
4 files changed, 319 insertions(+)
create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
create mode 100644 include/linux/mfd/imx25-tsadc.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 2e6b7311fabc..44fc15598a6a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -232,6 +232,16 @@ config MFD_MC13XXX_I2C
help
Select this if your MC13xxx is connected via an I2C bus.
+config MFD_MX25_TSADC
+ tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
+ select REGMAP_MMIO
+ depends on SOC_IMX25
+ depends on OF
+ help
+ Enable support for the integrated Touchscreen and ADC unit of the
+ i.MX25 processors. They consist of a conversion queue for general
+ purpose ADC and a queue for Touchscreens.
+
config MFD_HI6421_PMIC
tristate "HiSilicon Hi6421 PMU/Codec IC"
depends on OF
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 53467e211381..3feeb29f5938 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -78,6 +78,8 @@ obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o
obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
obj-$(CONFIG_TWL6040_CORE) += twl6040.o
+obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
+
obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
diff --git a/drivers/mfd/fsl-imx25-tsadc.c b/drivers/mfd/fsl-imx25-tsadc.c
new file mode 100644
index 000000000000..8e4013d57500
--- /dev/null
+++ b/drivers/mfd/fsl-imx25-tsadc.c
@@ -0,0 +1,167 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdesc.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static struct regmap_config mx25_tsadc_regmap_config = {
+ .fast_io = true,
+ .max_register = 8,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static void mx25_tsadc_irq_handler(u32 irq, struct irq_desc *desc)
+{
+ struct mx25_tsadc *tsadc = irq_desc_get_handler_data(desc);
+ struct irq_chip *chip = irq_get_chip(irq);
+ u32 status;
+
+ chained_irq_enter(chip, desc);
+
+ regmap_read(tsadc->regs, MX25_TSC_TGSR, &status);
+
+ if (status & MX25_TGSR_GCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 1));
+
+ if (status & MX25_TGSR_TCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 0));
+
+ chained_irq_exit(chip, desc);
+}
+
+static int mx25_tsadc_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ struct mx25_tsadc *tsadc = d->host_data;
+
+ irq_set_chip_data(irq, tsadc);
+ irq_set_chip_and_handler(irq, &dummy_irq_chip,
+ handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+static struct irq_domain_ops mx25_tsadc_domain_ops = {
+ .map = mx25_tsadc_domain_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int mx25_tsadc_setup_irq(struct platform_device *pdev,
+ struct mx25_tsadc *tsadc)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ int irq;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "Failed to get irq\n");
+ return irq;
+ }
+
+ tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
+ tsadc);
+ if (!tsadc->domain) {
+ dev_err(dev, "Failed to add irq domain\n");
+ return -ENOMEM;
+ }
+
+ irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
+ irq_set_handler_data(irq, tsadc);
+
+ return 0;
+}
+
+static int mx25_tsadc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct mx25_tsadc *tsadc;
+ struct resource *res;
+ int ret;
+ void __iomem *iomem;
+
+ tsadc = devm_kzalloc(dev, sizeof(*tsadc), GFP_KERNEL);
+ if (!tsadc)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ iomem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(iomem))
+ return PTR_ERR(iomem);
+
+ tsadc->regs = devm_regmap_init_mmio(dev, iomem,
+ &mx25_tsadc_regmap_config);
+ if (IS_ERR(tsadc->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(tsadc->regs);
+ }
+
+ tsadc->clk = devm_clk_get(dev, "ipg");
+ if (IS_ERR(tsadc->clk)) {
+ dev_err(dev, "Failed to get ipg clock\n");
+ return PTR_ERR(tsadc->clk);
+ }
+
+ /* Enable clock and reset the component */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_CLK_EN,
+ MX25_TGCR_CLK_EN);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_TSC_RST,
+ MX25_TGCR_TSC_RST);
+
+ /* Setup powersaving mode, but enable internal reference voltage */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_POWERMODE_MASK,
+ MX25_TGCR_POWERMODE_SAVE);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_INTREFEN,
+ MX25_TGCR_INTREFEN);
+
+ ret = mx25_tsadc_setup_irq(pdev, tsadc);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, tsadc);
+
+ of_platform_populate(np, NULL, NULL, dev);
+
+ return 0;
+}
+
+static const struct of_device_id mx25_tsadc_ids[] = {
+ { .compatible = "fsl,imx25-tsadc" },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_tsadc_driver = {
+ .driver = {
+ .name = "mx25-tsadc",
+ .of_match_table = of_match_ptr(mx25_tsadc_ids),
+ },
+ .probe = mx25_tsadc_probe,
+};
+module_platform_driver(mx25_tsadc_driver);
+
+MODULE_DESCRIPTION("MFD for ADC/TSC for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:mx25-tsadc");
diff --git a/include/linux/mfd/imx25-tsadc.h b/include/linux/mfd/imx25-tsadc.h
new file mode 100644
index 000000000000..8086f18847fe
--- /dev/null
+++ b/include/linux/mfd/imx25-tsadc.h
@@ -0,0 +1,140 @@
+#ifndef _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
+#define _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
+
+struct regmap;
+struct device;
+struct clk;
+
+struct mx25_tsadc {
+ struct regmap *regs;
+ struct irq_domain *domain;
+ struct clk *clk;
+};
+
+#define MX25_TSC_TGCR 0x00
+#define MX25_TSC_TGSR 0x04
+#define MX25_TSC_TICR 0x08
+
+/* The same register layout for TC and GC queue */
+#define MX25_ADCQ_FIFO 0x00
+#define MX25_ADCQ_CR 0x04
+#define MX25_ADCQ_SR 0x08
+#define MX25_ADCQ_MR 0x0c
+#define MX25_ADCQ_ITEM_7_0 0x20
+#define MX25_ADCQ_ITEM_15_8 0x24
+#define MX25_ADCQ_CFG(n) (0x40 + ((n) * 0x4))
+
+/* Register values */
+/* Queue Config register */
+#define MX25_ADCQ_MR_MASK 0xffffffff
+
+/* TGCR */
+#define MX25_TGCR_PDBTIME(x) ((x) << 25)
+#define MX25_TGCR_PDBTIME_MASK MX25_TGCR_PDBTIME(0x7f)
+#define MX25_TGCR_PDBEN BIT(24)
+#define MX25_TGCR_PDEN BIT(23)
+#define MX25_TGCR_ADCCLKCFG(x) ((x) << 16)
+#define MX25_TGCR_GET_ADCCLK(x) (((x) >> 16) & 0x1f)
+#define MX25_TGCR_INTREFEN BIT(10)
+#define MX25_TGCR_POWERMODE_MASK (3 << 8)
+#define MX25_TGCR_POWERMODE_SAVE BIT(8)
+#define MX25_TGCR_POWERMODE_ON (2 << 8)
+#define MX25_TGCR_STLC BIT(5)
+#define MX25_TGCR_SLPC BIT(4)
+#define MX25_TGCR_FUNC_RST BIT(2)
+#define MX25_TGCR_TSC_RST BIT(1)
+#define MX25_TGCR_CLK_EN BIT(0)
+
+/* TGSR */
+#define MX25_TGSR_SLP_INT BIT(2)
+#define MX25_TGSR_GCQ_INT BIT(1)
+#define MX25_TGSR_TCQ_INT BIT(0)
+
+/* ADCQ_ITEM_* */
+#define _MX25_ADCQ_ITEM(item, x) ((x) << ((item) * 4))
+#define MX25_ADCQ_ITEM(item, x) ((item) >= 8 ? \
+ _MX25_ADCQ_ITEM((item) - 8, (x)) : _MX25_ADCQ_ITEM((item), (x)))
+
+/* ADCQ_FIFO (TCQFIFO and GCQFIFO) */
+#define MX25_ADCQ_FIFO_DATA(x) (((x) >> 4) & 0xfff)
+#define MX25_ADCQ_FIFO_ID(x) ((x) & 0xf)
+
+/* ADCQ_CR (TCQR and GCQR) */
+#define MX25_ADCQ_CR_PDCFG_LEVEL BIT(19)
+#define MX25_ADCQ_CR_PDMSK BIT(18)
+#define MX25_ADCQ_CR_FRST BIT(17)
+#define MX25_ADCQ_CR_QRST BIT(16)
+#define MX25_ADCQ_CR_RWAIT_MASK (0xf << 12)
+#define MX25_ADCQ_CR_RWAIT(x) ((x) << 12)
+#define MX25_ADCQ_CR_WMRK_MASK (0xf << 8)
+#define MX25_ADCQ_CR_WMRK(x) ((x) << 8)
+#define MX25_ADCQ_CR_LITEMID_MASK (0xf << 4)
+#define MX25_ADCQ_CR_LITEMID(x) ((x) << 4)
+#define MX25_ADCQ_CR_RPT BIT(3)
+#define MX25_ADCQ_CR_FQS BIT(2)
+#define MX25_ADCQ_CR_QSM_MASK 0x3
+#define MX25_ADCQ_CR_QSM_PD 0x1
+#define MX25_ADCQ_CR_QSM_FQS 0x2
+#define MX25_ADCQ_CR_QSM_FQS_PD 0x3
+
+/* ADCQ_SR (TCQSR and GCQSR) */
+#define MX25_ADCQ_SR_FDRY BIT(15)
+#define MX25_ADCQ_SR_FULL BIT(14)
+#define MX25_ADCQ_SR_EMPT BIT(13)
+#define MX25_ADCQ_SR_FDN(x) (((x) >> 8) & 0x1f)
+#define MX25_ADCQ_SR_FRR BIT(6)
+#define MX25_ADCQ_SR_FUR BIT(5)
+#define MX25_ADCQ_SR_FOR BIT(4)
+#define MX25_ADCQ_SR_EOQ BIT(1)
+#define MX25_ADCQ_SR_PD BIT(0)
+
+/* ADCQ_MR (TCQMR and GCQMR) */
+#define MX25_ADCQ_MR_FDRY_DMA BIT(31)
+#define MX25_ADCQ_MR_FER_DMA BIT(22)
+#define MX25_ADCQ_MR_FUR_DMA BIT(21)
+#define MX25_ADCQ_MR_FOR_DMA BIT(20)
+#define MX25_ADCQ_MR_EOQ_DMA BIT(17)
+#define MX25_ADCQ_MR_PD_DMA BIT(16)
+#define MX25_ADCQ_MR_FDRY_IRQ BIT(15)
+#define MX25_ADCQ_MR_FER_IRQ BIT(6)
+#define MX25_ADCQ_MR_FUR_IRQ BIT(5)
+#define MX25_ADCQ_MR_FOR_IRQ BIT(4)
+#define MX25_ADCQ_MR_EOQ_IRQ BIT(1)
+#define MX25_ADCQ_MR_PD_IRQ BIT(0)
+
+/* ADCQ_CFG (TICR, TCC0-7,GCC0-7) */
+#define MX25_ADCQ_CFG_SETTLING_TIME(x) ((x) << 24)
+#define MX25_ADCQ_CFG_IGS BIT(20)
+#define MX25_ADCQ_CFG_NOS_MASK (0xf << 16)
+#define MX25_ADCQ_CFG_NOS(x) (((x) - 1) << 16)
+#define MX25_ADCQ_CFG_WIPER BIT(15)
+#define MX25_ADCQ_CFG_YNLR BIT(14)
+#define MX25_ADCQ_CFG_YPLL_HIGH 0
+#define MX25_ADCQ_CFG_YPLL_OFF BIT(12)
+#define MX25_ADCQ_CFG_YPLL_LOW (3 << 12)
+#define MX25_ADCQ_CFG_XNUR_HIGH 0
+#define MX25_ADCQ_CFG_XNUR_OFF BIT(10)
+#define MX25_ADCQ_CFG_XNUR_LOW (3 << 10)
+#define MX25_ADCQ_CFG_XPUL_OFF BIT(9)
+#define MX25_ADCQ_CFG_XPUL_HIGH 0
+#define MX25_ADCQ_CFG_REFP_YP 0
+#define MX25_ADCQ_CFG_REFP_XP BIT(7)
+#define MX25_ADCQ_CFG_REFP_EXT (2 << 7)
+#define MX25_ADCQ_CFG_REFP_INT (3 << 7)
+#define MX25_ADCQ_CFG_REFP_MASK (3 << 7)
+#define MX25_ADCQ_CFG_IN_XP 0
+#define MX25_ADCQ_CFG_IN_YP BIT(4)
+#define MX25_ADCQ_CFG_IN_XN (2 << 4)
+#define MX25_ADCQ_CFG_IN_YN (3 << 4)
+#define MX25_ADCQ_CFG_IN_WIPER (4 << 4)
+#define MX25_ADCQ_CFG_IN_AUX0 (5 << 4)
+#define MX25_ADCQ_CFG_IN_AUX1 (6 << 4)
+#define MX25_ADCQ_CFG_IN_AUX2 (7 << 4)
+#define MX25_ADCQ_CFG_REFN_XN 0
+#define MX25_ADCQ_CFG_REFN_YN BIT(2)
+#define MX25_ADCQ_CFG_REFN_NGND (2 << 2)
+#define MX25_ADCQ_CFG_REFN_NGND2 (3 << 2)
+#define MX25_ADCQ_CFG_REFN_MASK (3 << 2)
+#define MX25_ADCQ_CFG_PENIACK BIT(1)
+
+#endif /* _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_ */
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.
This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
---
Notes:
Changes in v5:
- Remove ifdef CONFIG_OF as this driver is only for DT usage
- Remove module owner
- Add Kconfig dependencies ARCH_MX25 and OF
@Jonathan Cameron:
I left your acked-by on the patch as these were small changes. If it should be
removed, please say so. Thanks
drivers/mfd/Kconfig | 10 +++
drivers/mfd/Makefile | 2 +
drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/imx25-tsadc.h | 140 +++++++++++++++++++++++++++++++++
4 files changed, 319 insertions(+)
create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
create mode 100644 include/linux/mfd/imx25-tsadc.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 2e6b7311fabc..44fc15598a6a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -232,6 +232,16 @@ config MFD_MC13XXX_I2C
help
Select this if your MC13xxx is connected via an I2C bus.
+config MFD_MX25_TSADC
+ tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
+ select REGMAP_MMIO
+ depends on SOC_IMX25
+ depends on OF
+ help
+ Enable support for the integrated Touchscreen and ADC unit of the
+ i.MX25 processors. They consist of a conversion queue for general
+ purpose ADC and a queue for Touchscreens.
+
config MFD_HI6421_PMIC
tristate "HiSilicon Hi6421 PMU/Codec IC"
depends on OF
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 53467e211381..3feeb29f5938 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -78,6 +78,8 @@ obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o
obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
obj-$(CONFIG_TWL6040_CORE) += twl6040.o
+obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
+
obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
diff --git a/drivers/mfd/fsl-imx25-tsadc.c b/drivers/mfd/fsl-imx25-tsadc.c
new file mode 100644
index 000000000000..8e4013d57500
--- /dev/null
+++ b/drivers/mfd/fsl-imx25-tsadc.c
@@ -0,0 +1,167 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdesc.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static struct regmap_config mx25_tsadc_regmap_config = {
+ .fast_io = true,
+ .max_register = 8,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static void mx25_tsadc_irq_handler(u32 irq, struct irq_desc *desc)
+{
+ struct mx25_tsadc *tsadc = irq_desc_get_handler_data(desc);
+ struct irq_chip *chip = irq_get_chip(irq);
+ u32 status;
+
+ chained_irq_enter(chip, desc);
+
+ regmap_read(tsadc->regs, MX25_TSC_TGSR, &status);
+
+ if (status & MX25_TGSR_GCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 1));
+
+ if (status & MX25_TGSR_TCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 0));
+
+ chained_irq_exit(chip, desc);
+}
+
+static int mx25_tsadc_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ struct mx25_tsadc *tsadc = d->host_data;
+
+ irq_set_chip_data(irq, tsadc);
+ irq_set_chip_and_handler(irq, &dummy_irq_chip,
+ handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+static struct irq_domain_ops mx25_tsadc_domain_ops = {
+ .map = mx25_tsadc_domain_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int mx25_tsadc_setup_irq(struct platform_device *pdev,
+ struct mx25_tsadc *tsadc)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ int irq;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "Failed to get irq\n");
+ return irq;
+ }
+
+ tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
+ tsadc);
+ if (!tsadc->domain) {
+ dev_err(dev, "Failed to add irq domain\n");
+ return -ENOMEM;
+ }
+
+ irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
+ irq_set_handler_data(irq, tsadc);
+
+ return 0;
+}
+
+static int mx25_tsadc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct mx25_tsadc *tsadc;
+ struct resource *res;
+ int ret;
+ void __iomem *iomem;
+
+ tsadc = devm_kzalloc(dev, sizeof(*tsadc), GFP_KERNEL);
+ if (!tsadc)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ iomem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(iomem))
+ return PTR_ERR(iomem);
+
+ tsadc->regs = devm_regmap_init_mmio(dev, iomem,
+ &mx25_tsadc_regmap_config);
+ if (IS_ERR(tsadc->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(tsadc->regs);
+ }
+
+ tsadc->clk = devm_clk_get(dev, "ipg");
+ if (IS_ERR(tsadc->clk)) {
+ dev_err(dev, "Failed to get ipg clock\n");
+ return PTR_ERR(tsadc->clk);
+ }
+
+ /* Enable clock and reset the component */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_CLK_EN,
+ MX25_TGCR_CLK_EN);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_TSC_RST,
+ MX25_TGCR_TSC_RST);
+
+ /* Setup powersaving mode, but enable internal reference voltage */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_POWERMODE_MASK,
+ MX25_TGCR_POWERMODE_SAVE);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_INTREFEN,
+ MX25_TGCR_INTREFEN);
+
+ ret = mx25_tsadc_setup_irq(pdev, tsadc);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, tsadc);
+
+ of_platform_populate(np, NULL, NULL, dev);
+
+ return 0;
+}
+
+static const struct of_device_id mx25_tsadc_ids[] = {
+ { .compatible = "fsl,imx25-tsadc" },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_tsadc_driver = {
+ .driver = {
+ .name = "mx25-tsadc",
+ .of_match_table = of_match_ptr(mx25_tsadc_ids),
+ },
+ .probe = mx25_tsadc_probe,
+};
+module_platform_driver(mx25_tsadc_driver);
+
+MODULE_DESCRIPTION("MFD for ADC/TSC for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:mx25-tsadc");
diff --git a/include/linux/mfd/imx25-tsadc.h b/include/linux/mfd/imx25-tsadc.h
new file mode 100644
index 000000000000..8086f18847fe
--- /dev/null
+++ b/include/linux/mfd/imx25-tsadc.h
@@ -0,0 +1,140 @@
+#ifndef _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
+#define _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
+
+struct regmap;
+struct device;
+struct clk;
+
+struct mx25_tsadc {
+ struct regmap *regs;
+ struct irq_domain *domain;
+ struct clk *clk;
+};
+
+#define MX25_TSC_TGCR 0x00
+#define MX25_TSC_TGSR 0x04
+#define MX25_TSC_TICR 0x08
+
+/* The same register layout for TC and GC queue */
+#define MX25_ADCQ_FIFO 0x00
+#define MX25_ADCQ_CR 0x04
+#define MX25_ADCQ_SR 0x08
+#define MX25_ADCQ_MR 0x0c
+#define MX25_ADCQ_ITEM_7_0 0x20
+#define MX25_ADCQ_ITEM_15_8 0x24
+#define MX25_ADCQ_CFG(n) (0x40 + ((n) * 0x4))
+
+/* Register values */
+/* Queue Config register */
+#define MX25_ADCQ_MR_MASK 0xffffffff
+
+/* TGCR */
+#define MX25_TGCR_PDBTIME(x) ((x) << 25)
+#define MX25_TGCR_PDBTIME_MASK MX25_TGCR_PDBTIME(0x7f)
+#define MX25_TGCR_PDBEN BIT(24)
+#define MX25_TGCR_PDEN BIT(23)
+#define MX25_TGCR_ADCCLKCFG(x) ((x) << 16)
+#define MX25_TGCR_GET_ADCCLK(x) (((x) >> 16) & 0x1f)
+#define MX25_TGCR_INTREFEN BIT(10)
+#define MX25_TGCR_POWERMODE_MASK (3 << 8)
+#define MX25_TGCR_POWERMODE_SAVE BIT(8)
+#define MX25_TGCR_POWERMODE_ON (2 << 8)
+#define MX25_TGCR_STLC BIT(5)
+#define MX25_TGCR_SLPC BIT(4)
+#define MX25_TGCR_FUNC_RST BIT(2)
+#define MX25_TGCR_TSC_RST BIT(1)
+#define MX25_TGCR_CLK_EN BIT(0)
+
+/* TGSR */
+#define MX25_TGSR_SLP_INT BIT(2)
+#define MX25_TGSR_GCQ_INT BIT(1)
+#define MX25_TGSR_TCQ_INT BIT(0)
+
+/* ADCQ_ITEM_* */
+#define _MX25_ADCQ_ITEM(item, x) ((x) << ((item) * 4))
+#define MX25_ADCQ_ITEM(item, x) ((item) >= 8 ? \
+ _MX25_ADCQ_ITEM((item) - 8, (x)) : _MX25_ADCQ_ITEM((item), (x)))
+
+/* ADCQ_FIFO (TCQFIFO and GCQFIFO) */
+#define MX25_ADCQ_FIFO_DATA(x) (((x) >> 4) & 0xfff)
+#define MX25_ADCQ_FIFO_ID(x) ((x) & 0xf)
+
+/* ADCQ_CR (TCQR and GCQR) */
+#define MX25_ADCQ_CR_PDCFG_LEVEL BIT(19)
+#define MX25_ADCQ_CR_PDMSK BIT(18)
+#define MX25_ADCQ_CR_FRST BIT(17)
+#define MX25_ADCQ_CR_QRST BIT(16)
+#define MX25_ADCQ_CR_RWAIT_MASK (0xf << 12)
+#define MX25_ADCQ_CR_RWAIT(x) ((x) << 12)
+#define MX25_ADCQ_CR_WMRK_MASK (0xf << 8)
+#define MX25_ADCQ_CR_WMRK(x) ((x) << 8)
+#define MX25_ADCQ_CR_LITEMID_MASK (0xf << 4)
+#define MX25_ADCQ_CR_LITEMID(x) ((x) << 4)
+#define MX25_ADCQ_CR_RPT BIT(3)
+#define MX25_ADCQ_CR_FQS BIT(2)
+#define MX25_ADCQ_CR_QSM_MASK 0x3
+#define MX25_ADCQ_CR_QSM_PD 0x1
+#define MX25_ADCQ_CR_QSM_FQS 0x2
+#define MX25_ADCQ_CR_QSM_FQS_PD 0x3
+
+/* ADCQ_SR (TCQSR and GCQSR) */
+#define MX25_ADCQ_SR_FDRY BIT(15)
+#define MX25_ADCQ_SR_FULL BIT(14)
+#define MX25_ADCQ_SR_EMPT BIT(13)
+#define MX25_ADCQ_SR_FDN(x) (((x) >> 8) & 0x1f)
+#define MX25_ADCQ_SR_FRR BIT(6)
+#define MX25_ADCQ_SR_FUR BIT(5)
+#define MX25_ADCQ_SR_FOR BIT(4)
+#define MX25_ADCQ_SR_EOQ BIT(1)
+#define MX25_ADCQ_SR_PD BIT(0)
+
+/* ADCQ_MR (TCQMR and GCQMR) */
+#define MX25_ADCQ_MR_FDRY_DMA BIT(31)
+#define MX25_ADCQ_MR_FER_DMA BIT(22)
+#define MX25_ADCQ_MR_FUR_DMA BIT(21)
+#define MX25_ADCQ_MR_FOR_DMA BIT(20)
+#define MX25_ADCQ_MR_EOQ_DMA BIT(17)
+#define MX25_ADCQ_MR_PD_DMA BIT(16)
+#define MX25_ADCQ_MR_FDRY_IRQ BIT(15)
+#define MX25_ADCQ_MR_FER_IRQ BIT(6)
+#define MX25_ADCQ_MR_FUR_IRQ BIT(5)
+#define MX25_ADCQ_MR_FOR_IRQ BIT(4)
+#define MX25_ADCQ_MR_EOQ_IRQ BIT(1)
+#define MX25_ADCQ_MR_PD_IRQ BIT(0)
+
+/* ADCQ_CFG (TICR, TCC0-7,GCC0-7) */
+#define MX25_ADCQ_CFG_SETTLING_TIME(x) ((x) << 24)
+#define MX25_ADCQ_CFG_IGS BIT(20)
+#define MX25_ADCQ_CFG_NOS_MASK (0xf << 16)
+#define MX25_ADCQ_CFG_NOS(x) (((x) - 1) << 16)
+#define MX25_ADCQ_CFG_WIPER BIT(15)
+#define MX25_ADCQ_CFG_YNLR BIT(14)
+#define MX25_ADCQ_CFG_YPLL_HIGH 0
+#define MX25_ADCQ_CFG_YPLL_OFF BIT(12)
+#define MX25_ADCQ_CFG_YPLL_LOW (3 << 12)
+#define MX25_ADCQ_CFG_XNUR_HIGH 0
+#define MX25_ADCQ_CFG_XNUR_OFF BIT(10)
+#define MX25_ADCQ_CFG_XNUR_LOW (3 << 10)
+#define MX25_ADCQ_CFG_XPUL_OFF BIT(9)
+#define MX25_ADCQ_CFG_XPUL_HIGH 0
+#define MX25_ADCQ_CFG_REFP_YP 0
+#define MX25_ADCQ_CFG_REFP_XP BIT(7)
+#define MX25_ADCQ_CFG_REFP_EXT (2 << 7)
+#define MX25_ADCQ_CFG_REFP_INT (3 << 7)
+#define MX25_ADCQ_CFG_REFP_MASK (3 << 7)
+#define MX25_ADCQ_CFG_IN_XP 0
+#define MX25_ADCQ_CFG_IN_YP BIT(4)
+#define MX25_ADCQ_CFG_IN_XN (2 << 4)
+#define MX25_ADCQ_CFG_IN_YN (3 << 4)
+#define MX25_ADCQ_CFG_IN_WIPER (4 << 4)
+#define MX25_ADCQ_CFG_IN_AUX0 (5 << 4)
+#define MX25_ADCQ_CFG_IN_AUX1 (6 << 4)
+#define MX25_ADCQ_CFG_IN_AUX2 (7 << 4)
+#define MX25_ADCQ_CFG_REFN_XN 0
+#define MX25_ADCQ_CFG_REFN_YN BIT(2)
+#define MX25_ADCQ_CFG_REFN_NGND (2 << 2)
+#define MX25_ADCQ_CFG_REFN_NGND2 (3 << 2)
+#define MX25_ADCQ_CFG_REFN_MASK (3 << 2)
+#define MX25_ADCQ_CFG_PENIACK BIT(1)
+
+#endif /* _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_ */
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 2/6] ARM: dt: Binding documentation for imx25 ADC/TSC
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
This documentation describes the devicetree bindings for the
ADC/Touchscreen unit of the i.MX25 SoC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
.../devicetree/bindings/mfd/fsl-imx25-tsadc.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
diff --git a/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
new file mode 100644
index 000000000000..a857af0eb68c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
@@ -0,0 +1,46 @@
+Freescale mx25 ADC/TSC multifunction device
+
+This device combines two general purpose conversion queues one used for general
+ADC and the other used for touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tsadc".
+ - reg: Memory range of the device.
+ - interrupts: Interrupt for this device as described in
+ interrupts/interrupts.txt
+ - clocks: An 'ipg' clock defined as described in clocks/clock.txt
+ - interrupt-controller: This device is an interrupt controller. It controls
+ the interrupts of both conversion queues.
+ - #interrupt-cells: Should be '<1>'.
+ - #address-cells: Should be '<1>'.
+ - #size-cells: Should be '<1>'.
+ - ranges
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tscadc: tscadc@50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
+ interrupts = <46>;
+ clocks = <&clks 119>;
+ clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ ...
+ };
+
+ adc: gcq@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ ...
+ };
+ };
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 2/6] ARM: dt: Binding documentation for imx25 ADC/TSC
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
This documentation describes the devicetree bindings for the
ADC/Touchscreen unit of the i.MX25 SoC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
.../devicetree/bindings/mfd/fsl-imx25-tsadc.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
diff --git a/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
new file mode 100644
index 000000000000..a857af0eb68c
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/fsl-imx25-tsadc.txt
@@ -0,0 +1,46 @@
+Freescale mx25 ADC/TSC multifunction device
+
+This device combines two general purpose conversion queues one used for general
+ADC and the other used for touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tsadc".
+ - reg: Memory range of the device.
+ - interrupts: Interrupt for this device as described in
+ interrupts/interrupts.txt
+ - clocks: An 'ipg' clock defined as described in clocks/clock.txt
+ - interrupt-controller: This device is an interrupt controller. It controls
+ the interrupts of both conversion queues.
+ - #interrupt-cells: Should be '<1>'.
+ - #address-cells: Should be '<1>'.
+ - #size-cells: Should be '<1>'.
+ - ranges
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tscadc: tscadc at 50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
+ interrupts = <46>;
+ clocks = <&clks 119>;
+ clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ tsc: tcq at 50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ ...
+ };
+
+ adc: gcq at 50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ ...
+ };
+ };
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.
The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
Notes:
Changes in v5:
- Fixed locking
- Removed module owner
.../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
5 files changed, 439 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
new file mode 100644
index 000000000000..d55b6b751349
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
@@ -0,0 +1,51 @@
+Freescale i.MX25 ADC GCQ device
+
+This is a generic conversion queue device that can convert any of the
+analog inputs using the ADC unit of the i.MX25.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-gcq".
+ - reg: Should be the register range of the module.
+ - interrupts: Should be the interrupt number of the module.
+ Typically this is <1>.
+ - interrupt-parent: phandle to the tsadc module of the i.MX25.
+ - #address-cells: Should be <1> (setting for the subnodes)
+ - #size-cells: Should be <0> (setting for the subnodes)
+
+Optional properties:
+ - vref-supply: The regulator supplying the ADC reference voltage.
+ Required when at least one subnode uses the external reference.
+
+Sub-nodes:
+Optionally you can define subnodes which define the reference voltage
+for the analog inputs.
+
+Required properties for subnodes:
+ - reg: Should be the number of the analog input.
+ 0: xp
+ 1: yp
+ 2: xn
+ 3: yn
+ 4: wiper
+ 5: inaux0
+ 6: inaux1
+ 7: inaux2
+ - fsl,adc-ref: specifies the reference input as defined in
+ <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+ MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
+
+Example:
+
+ adc: adc@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ inaux@5 {
+ reg = <5>;
+ fsl,adc-ref = <MX25_ADC_REF_INT>;
+ };
+ };
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 0f79e4725763..fccbb4bf44cc 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -143,6 +143,13 @@ config EXYNOS_ADC
of SoCs for drivers such as the touchscreen and hwmon to use to share
this resource.
+config FSL_MX25_ADC
+ tristate "Freescale MX25 ADC driver"
+ depends on MFD_MX25_TSADC
+ help
+ Generic Conversion Queue driver used for general purpose ADC in the
+ MX25. This driver supports single measurements using the MX25 ADC.
+
config LP8788_ADC
tristate "LP8788 ADC driver"
depends on MFD_LP8788
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 701fdb7c96aa..acab8d956371 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
obj-$(CONFIG_AT91_ADC) += at91_adc.o
obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
+obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
obj-$(CONFIG_MAX1027) += max1027.o
obj-$(CONFIG_MAX1363) += max1363.o
diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
new file mode 100644
index 000000000000..c1ac5af41ec5
--- /dev/null
+++ b/drivers/iio/adc/fsl-imx25-gcq.c
@@ -0,0 +1,369 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * This is the driver for the imx25 GCQ (Generic Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+#include <linux/clk.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
+
+enum mx25_gcq_cfgs {
+ MX25_CFG_XP = 0,
+ MX25_CFG_YP,
+ MX25_CFG_XN,
+ MX25_CFG_YN,
+ MX25_CFG_WIPER,
+ MX25_CFG_INAUX0,
+ MX25_CFG_INAUX1,
+ MX25_CFG_INAUX2,
+ MX25_NUM_CFGS,
+};
+
+struct mx25_gcq_priv {
+ struct regmap *regs;
+ struct completion completed;
+ unsigned int settling_time;
+ struct clk *clk;
+ int irq;
+ struct regulator *ext_vref;
+ u32 channel_vref_mv[MX25_NUM_CFGS];
+};
+
+#define MX25_CQG_CHAN(chan, id) {\
+ .type = IIO_VOLTAGE,\
+ .indexed = 1,\
+ .channel = chan,\
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
+ .datasheet_name = id,\
+}
+
+static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
+ MX25_CQG_CHAN(0, "xp"),
+ MX25_CQG_CHAN(1, "yp"),
+ MX25_CQG_CHAN(2, "xn"),
+ MX25_CQG_CHAN(3, "yn"),
+ MX25_CQG_CHAN(4, "wiper"),
+ MX25_CQG_CHAN(5, "inaux0"),
+ MX25_CQG_CHAN(6, "inaux1"),
+ MX25_CQG_CHAN(7, "inaux2"),
+};
+
+static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
+ MX25_ADCQ_MR_EOQ_IRQ);
+}
+
+static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR,
+ MX25_ADCQ_MR_EOQ_IRQ, 0);
+}
+
+static irqreturn_t mx25_gcq_irq(int irq, void *data)
+{
+ struct mx25_gcq_priv *priv = data;
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+
+ if (stats & MX25_ADCQ_SR_EOQ) {
+ mx25_gcq_disable_eoq(priv);
+ complete(&priv->completed);
+ }
+
+ /* Disable conversion queue run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
+
+ /* Acknowledge all possible irqs */
+ regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
+
+ return IRQ_HANDLED;
+}
+
+static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val,
+ int *val2, long mask)
+{
+ struct mx25_gcq_priv *priv = iio_priv(indio_dev);
+ long timeout;
+ u32 data;
+ int ret = 0;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ mutex_lock(&indio_dev->mlock);
+
+ /* Setup the configuration we want to use */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, chan->channel));
+
+ mx25_gcq_enable_eoq(priv);
+
+ /* Trigger queue for one run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+
+ timeout = wait_for_completion_interruptible_timeout(
+ &priv->completed, MX25_GCQ_TIMEOUT);
+ if (timeout < 0) {
+ dev_err(&indio_dev->dev,
+ "ADC wait for measurement failed\n");
+ ret = timeout;
+ goto info_raw_out;
+ } else if (timeout == 0) {
+ dev_err(&indio_dev->dev, "ADC timed out\n");
+ ret = -ETIMEDOUT;
+ goto info_raw_out;
+ }
+
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
+
+ *val = MX25_ADCQ_FIFO_DATA(data);
+ ret = IIO_VAL_INT;
+info_raw_out:
+ mutex_unlock(&indio_dev->mlock);
+
+ return ret;
+
+ case IIO_CHAN_INFO_SCALE:
+ *val = priv->channel_vref_mv[chan->channel];
+ *val2 = 12;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info mx25_gcq_iio_info = {
+ .read_raw = mx25_gcq_read_raw,
+};
+
+static const struct regmap_config mx25_gcq_regconfig = {
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
+ struct mx25_gcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ struct device *dev = &pdev->dev;
+ int ret, i;
+
+ /*
+ * Setup all configurations registers with a default conversion
+ * configuration for each input
+ */
+ for (i = 0; i < MX25_NUM_CFGS; ++i)
+ regmap_write(priv->regs, MX25_ADCQ_CFG(i),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_INT |
+ (i << 4) |
+ MX25_ADCQ_CFG_REFN_NGND2);
+
+ for_each_child_of_node(np, child) {
+ u32 reg;
+ u32 refp;
+ u32 adc_ref;
+
+ ret = of_property_read_u32(child, "reg", ®);
+ if (ret) {
+ dev_err(dev, "Failed to get reg property\n");
+ return ret;
+ }
+
+ if (reg >= MX25_NUM_CFGS) {
+ dev_err(dev,
+ "reg value is greater than the number of available configuration registers\n");
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
+ if (ret) {
+ dev_err(dev, "Failed to get fsl,adc-ref property\n");
+ return ret;
+ }
+
+ if (adc_ref != MX25_ADC_REF_INT &&
+ adc_ref != MX25_ADC_REF_EXT) {
+ dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
+ adc_ref);
+ return -EINVAL;
+ }
+
+ switch (adc_ref) {
+ case MX25_ADC_REF_EXT:
+ if (IS_ERR_OR_NULL(priv->ext_vref)) {
+ dev_err(dev,
+ "No regulator found for the external vref\n");
+ return -EINVAL;
+ }
+ priv->channel_vref_mv[reg] =
+ regulator_get_voltage(priv->ext_vref);
+ refp = MX25_ADCQ_CFG_REFP_EXT;
+ break;
+ case MX25_ADC_REF_INT:
+ priv->channel_vref_mv[reg] = 2500;
+ refp = MX25_ADCQ_CFG_REFP_INT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
+ MX25_ADCQ_CFG_REFP_MASK |
+ MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
+ (MX25_ADCQ_CFG_REFN_NGND << 2));
+ }
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
+
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_PDMSK |
+ MX25_ADCQ_CR_QSM_FQS);
+
+ return 0;
+}
+
+static int mx25_gcq_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev;
+ struct mx25_gcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (!mem)
+ return -ENOMEM;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ init_completion(&priv->completed);
+
+ /* Optional external regulator */
+ priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
+ if (!IS_ERR_OR_NULL(priv->ext_vref)) {
+ ret = regulator_enable(priv->ext_vref);
+ if (ret)
+ return ret;
+ }
+
+ ret = mx25_gcq_setup_cfgs(pdev, priv);
+ if (ret)
+ return ret;
+
+ priv->clk = tsadc->clk;
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable clock\n");
+ return ret;
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ ret = priv->irq;
+ goto err_clk_unprepare;
+ }
+
+ ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ goto err_clk_unprepare;
+ }
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->channels = mx25_gcq_channels;
+ indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
+ indio_dev->info = &mx25_gcq_iio_info;
+
+ ret = iio_device_register(indio_dev);
+ if (ret) {
+ dev_err(dev, "Failed to register iio device\n");
+ goto err_irq_free;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+err_irq_free:
+ free_irq(priv->irq, (void *)priv);
+err_clk_unprepare:
+ clk_disable_unprepare(priv->clk);
+ return ret;
+}
+
+static int mx25_gcq_remove(struct platform_device *pdev)
+{
+ struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
+
+ iio_device_unregister(indio_dev);
+ free_irq(priv->irq, priv);
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct of_device_id mx25_gcq_ids[] = {
+ { .compatible = "fsl,imx25-gcq", },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_gcq_driver = {
+ .driver = {
+ .name = "mx25-gcq",
+ .of_match_table = mx25_gcq_ids,
+ },
+ .probe = mx25_gcq_probe,
+ .remove = mx25_gcq_remove,
+};
+module_platform_driver(mx25_gcq_driver);
+
+MODULE_DESCRIPTION("ADC driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
new file mode 100644
index 000000000000..486dce735ac9
--- /dev/null
+++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
@@ -0,0 +1,11 @@
+/*
+ * This header provides constants for configuring the I.MX25 ADC
+ */
+
+#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+
+#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
+#define MX25_ADC_REF_EXT 1 /* External voltage reference */
+
+#endif
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.
The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
---
Notes:
Changes in v5:
- Fixed locking
- Removed module owner
.../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
drivers/iio/adc/Kconfig | 7 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
5 files changed, 439 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
new file mode 100644
index 000000000000..d55b6b751349
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
@@ -0,0 +1,51 @@
+Freescale i.MX25 ADC GCQ device
+
+This is a generic conversion queue device that can convert any of the
+analog inputs using the ADC unit of the i.MX25.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-gcq".
+ - reg: Should be the register range of the module.
+ - interrupts: Should be the interrupt number of the module.
+ Typically this is <1>.
+ - interrupt-parent: phandle to the tsadc module of the i.MX25.
+ - #address-cells: Should be <1> (setting for the subnodes)
+ - #size-cells: Should be <0> (setting for the subnodes)
+
+Optional properties:
+ - vref-supply: The regulator supplying the ADC reference voltage.
+ Required when at least one subnode uses the external reference.
+
+Sub-nodes:
+Optionally you can define subnodes which define the reference voltage
+for the analog inputs.
+
+Required properties for subnodes:
+ - reg: Should be the number of the analog input.
+ 0: xp
+ 1: yp
+ 2: xn
+ 3: yn
+ 4: wiper
+ 5: inaux0
+ 6: inaux1
+ 7: inaux2
+ - fsl,adc-ref: specifies the reference input as defined in
+ <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+ MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
+
+Example:
+
+ adc: adc at 50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ inaux at 5 {
+ reg = <5>;
+ fsl,adc-ref = <MX25_ADC_REF_INT>;
+ };
+ };
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 0f79e4725763..fccbb4bf44cc 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -143,6 +143,13 @@ config EXYNOS_ADC
of SoCs for drivers such as the touchscreen and hwmon to use to share
this resource.
+config FSL_MX25_ADC
+ tristate "Freescale MX25 ADC driver"
+ depends on MFD_MX25_TSADC
+ help
+ Generic Conversion Queue driver used for general purpose ADC in the
+ MX25. This driver supports single measurements using the MX25 ADC.
+
config LP8788_ADC
tristate "LP8788 ADC driver"
depends on MFD_LP8788
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 701fdb7c96aa..acab8d956371 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
obj-$(CONFIG_AT91_ADC) += at91_adc.o
obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
+obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
obj-$(CONFIG_MAX1027) += max1027.o
obj-$(CONFIG_MAX1363) += max1363.o
diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
new file mode 100644
index 000000000000..c1ac5af41ec5
--- /dev/null
+++ b/drivers/iio/adc/fsl-imx25-gcq.c
@@ -0,0 +1,369 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * This is the driver for the imx25 GCQ (Generic Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+#include <linux/clk.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
+
+enum mx25_gcq_cfgs {
+ MX25_CFG_XP = 0,
+ MX25_CFG_YP,
+ MX25_CFG_XN,
+ MX25_CFG_YN,
+ MX25_CFG_WIPER,
+ MX25_CFG_INAUX0,
+ MX25_CFG_INAUX1,
+ MX25_CFG_INAUX2,
+ MX25_NUM_CFGS,
+};
+
+struct mx25_gcq_priv {
+ struct regmap *regs;
+ struct completion completed;
+ unsigned int settling_time;
+ struct clk *clk;
+ int irq;
+ struct regulator *ext_vref;
+ u32 channel_vref_mv[MX25_NUM_CFGS];
+};
+
+#define MX25_CQG_CHAN(chan, id) {\
+ .type = IIO_VOLTAGE,\
+ .indexed = 1,\
+ .channel = chan,\
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
+ .datasheet_name = id,\
+}
+
+static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
+ MX25_CQG_CHAN(0, "xp"),
+ MX25_CQG_CHAN(1, "yp"),
+ MX25_CQG_CHAN(2, "xn"),
+ MX25_CQG_CHAN(3, "yn"),
+ MX25_CQG_CHAN(4, "wiper"),
+ MX25_CQG_CHAN(5, "inaux0"),
+ MX25_CQG_CHAN(6, "inaux1"),
+ MX25_CQG_CHAN(7, "inaux2"),
+};
+
+static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
+ MX25_ADCQ_MR_EOQ_IRQ);
+}
+
+static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR,
+ MX25_ADCQ_MR_EOQ_IRQ, 0);
+}
+
+static irqreturn_t mx25_gcq_irq(int irq, void *data)
+{
+ struct mx25_gcq_priv *priv = data;
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+
+ if (stats & MX25_ADCQ_SR_EOQ) {
+ mx25_gcq_disable_eoq(priv);
+ complete(&priv->completed);
+ }
+
+ /* Disable conversion queue run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
+
+ /* Acknowledge all possible irqs */
+ regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
+
+ return IRQ_HANDLED;
+}
+
+static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val,
+ int *val2, long mask)
+{
+ struct mx25_gcq_priv *priv = iio_priv(indio_dev);
+ long timeout;
+ u32 data;
+ int ret = 0;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ mutex_lock(&indio_dev->mlock);
+
+ /* Setup the configuration we want to use */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, chan->channel));
+
+ mx25_gcq_enable_eoq(priv);
+
+ /* Trigger queue for one run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+
+ timeout = wait_for_completion_interruptible_timeout(
+ &priv->completed, MX25_GCQ_TIMEOUT);
+ if (timeout < 0) {
+ dev_err(&indio_dev->dev,
+ "ADC wait for measurement failed\n");
+ ret = timeout;
+ goto info_raw_out;
+ } else if (timeout == 0) {
+ dev_err(&indio_dev->dev, "ADC timed out\n");
+ ret = -ETIMEDOUT;
+ goto info_raw_out;
+ }
+
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
+
+ *val = MX25_ADCQ_FIFO_DATA(data);
+ ret = IIO_VAL_INT;
+info_raw_out:
+ mutex_unlock(&indio_dev->mlock);
+
+ return ret;
+
+ case IIO_CHAN_INFO_SCALE:
+ *val = priv->channel_vref_mv[chan->channel];
+ *val2 = 12;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info mx25_gcq_iio_info = {
+ .read_raw = mx25_gcq_read_raw,
+};
+
+static const struct regmap_config mx25_gcq_regconfig = {
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
+ struct mx25_gcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ struct device *dev = &pdev->dev;
+ int ret, i;
+
+ /*
+ * Setup all configurations registers with a default conversion
+ * configuration for each input
+ */
+ for (i = 0; i < MX25_NUM_CFGS; ++i)
+ regmap_write(priv->regs, MX25_ADCQ_CFG(i),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_INT |
+ (i << 4) |
+ MX25_ADCQ_CFG_REFN_NGND2);
+
+ for_each_child_of_node(np, child) {
+ u32 reg;
+ u32 refp;
+ u32 adc_ref;
+
+ ret = of_property_read_u32(child, "reg", ®);
+ if (ret) {
+ dev_err(dev, "Failed to get reg property\n");
+ return ret;
+ }
+
+ if (reg >= MX25_NUM_CFGS) {
+ dev_err(dev,
+ "reg value is greater than the number of available configuration registers\n");
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
+ if (ret) {
+ dev_err(dev, "Failed to get fsl,adc-ref property\n");
+ return ret;
+ }
+
+ if (adc_ref != MX25_ADC_REF_INT &&
+ adc_ref != MX25_ADC_REF_EXT) {
+ dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
+ adc_ref);
+ return -EINVAL;
+ }
+
+ switch (adc_ref) {
+ case MX25_ADC_REF_EXT:
+ if (IS_ERR_OR_NULL(priv->ext_vref)) {
+ dev_err(dev,
+ "No regulator found for the external vref\n");
+ return -EINVAL;
+ }
+ priv->channel_vref_mv[reg] =
+ regulator_get_voltage(priv->ext_vref);
+ refp = MX25_ADCQ_CFG_REFP_EXT;
+ break;
+ case MX25_ADC_REF_INT:
+ priv->channel_vref_mv[reg] = 2500;
+ refp = MX25_ADCQ_CFG_REFP_INT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
+ MX25_ADCQ_CFG_REFP_MASK |
+ MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
+ (MX25_ADCQ_CFG_REFN_NGND << 2));
+ }
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
+
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_PDMSK |
+ MX25_ADCQ_CR_QSM_FQS);
+
+ return 0;
+}
+
+static int mx25_gcq_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev;
+ struct mx25_gcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (!mem)
+ return -ENOMEM;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ init_completion(&priv->completed);
+
+ /* Optional external regulator */
+ priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
+ if (!IS_ERR_OR_NULL(priv->ext_vref)) {
+ ret = regulator_enable(priv->ext_vref);
+ if (ret)
+ return ret;
+ }
+
+ ret = mx25_gcq_setup_cfgs(pdev, priv);
+ if (ret)
+ return ret;
+
+ priv->clk = tsadc->clk;
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable clock\n");
+ return ret;
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ ret = priv->irq;
+ goto err_clk_unprepare;
+ }
+
+ ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ goto err_clk_unprepare;
+ }
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->channels = mx25_gcq_channels;
+ indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
+ indio_dev->info = &mx25_gcq_iio_info;
+
+ ret = iio_device_register(indio_dev);
+ if (ret) {
+ dev_err(dev, "Failed to register iio device\n");
+ goto err_irq_free;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+err_irq_free:
+ free_irq(priv->irq, (void *)priv);
+err_clk_unprepare:
+ clk_disable_unprepare(priv->clk);
+ return ret;
+}
+
+static int mx25_gcq_remove(struct platform_device *pdev)
+{
+ struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
+
+ iio_device_unregister(indio_dev);
+ free_irq(priv->irq, priv);
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct of_device_id mx25_gcq_ids[] = {
+ { .compatible = "fsl,imx25-gcq", },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_gcq_driver = {
+ .driver = {
+ .name = "mx25-gcq",
+ .of_match_table = mx25_gcq_ids,
+ },
+ .probe = mx25_gcq_probe,
+ .remove = mx25_gcq_remove,
+};
+module_platform_driver(mx25_gcq_driver);
+
+MODULE_DESCRIPTION("ADC driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
new file mode 100644
index 000000000000..486dce735ac9
--- /dev/null
+++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
@@ -0,0 +1,11 @@
+/*
+ * This header provides constants for configuring the I.MX25 ADC
+ */
+
+#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+
+#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
+#define MX25_ADC_REF_EXT 1 /* External voltage reference */
+
+#endif
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 4/6] input: touchscreen: imx25 tcq driver
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
This is a driver for the imx25 ADC/TSC module. It controls the
touchscreen conversion queue and creates a touchscreen input device.
The driver currently only supports 4 wire touchscreens. The driver uses
a simple conversion queue of precharge, touch detection, X measurement,
Y measurement, precharge and another touch detection.
This driver uses the regmap from the parent to setup some touch specific
settings in the core driver and setup a idle configuration with touch
detection.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
---
Notes:
Changes in v5:
- Fix signed/unsigned comparison
- Fix unused variable settling_time by putting it in the correct argument list
- Use continous conversion queue with the repeat feature and a proper
repeat-wait. Previously the touchscreen caused massive number of interrupts.
.../bindings/input/touchscreen/fsl-mx25-tcq.txt | 29 +
drivers/input/touchscreen/Kconfig | 6 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/fsl-imx25-tcq.c | 587 +++++++++++++++++++++
4 files changed, 623 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
new file mode 100644
index 000000000000..4214a99d197a
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -0,0 +1,29 @@
+Freescale mx25 TS conversion queue module
+
+mx25 touchscreen conversion queue module which controls the ADC unit of the
+mx25 for attached touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tcq".
+ - reg: Memory range of the device.
+ - interrupts: Should be the interrupt number associated with this module within
+ the tscadc unit (<0>).
+ - interrupt-parent: Should be a phandle to the tscadc unit.
+ - fsl,wires: Should be '<4>' or '<5>'
+
+Optional properties:
+ - fsl,pen-debounce: Pen debounce time.
+ - fsl,pen-threshold: Pen-down threshold for the touchscreen.
+ - fsl,settling-time: Settling time in nanoseconds.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ };
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 58917525126e..f1534a0cd23f 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -748,6 +748,12 @@ config TOUCHSCREEN_USB_COMPOSITE
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MX25
+ tristate "Freescale i.MX25 touchscreen input driver"
+ depends on MFD_MX25_TSADC
+ help
+ Enable support for touchscreen connected to your i.MX25.
+
config TOUCHSCREEN_MC13783
tristate "Freescale MC13783 touchscreen input driver"
depends on MFD_MC13XXX
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 0242fea2102a..bbb55a69c33c 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o
diff --git a/drivers/input/touchscreen/fsl-imx25-tcq.c b/drivers/input/touchscreen/fsl-imx25-tcq.c
new file mode 100644
index 000000000000..2eb3bd00d56c
--- /dev/null
+++ b/drivers/input/touchscreen/fsl-imx25-tcq.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ * Based on driver from 2011:
+ * Juergen Beisert, Pengutronix <kernel@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <linux/clk.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static const char mx25_tcq_name[] = "mx25-tcq";
+
+enum mx25_tcq_mode {
+ MX25_TS_4WIRE,
+};
+
+struct mx25_tcq_priv {
+ struct regmap *regs;
+ struct regmap *core_regs;
+ struct input_dev *idev;
+ enum mx25_tcq_mode mode;
+ unsigned int pen_threshold;
+ unsigned int sample_count;
+ unsigned int expected_samples;
+ unsigned int pen_debounce;
+ unsigned int settling_time;
+ struct clk *clk;
+ int irq;
+};
+
+static struct regmap_config mx25_tcq_regconfig = {
+ .fast_io = true,
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static struct of_device_id mx25_tcq_ids[] = {
+ { .compatible = "fsl,imx25-tcq", },
+ { /* Sentinel */ }
+};
+
+#define TSC_4WIRE_PRE_INDEX 0
+#define TSC_4WIRE_X_INDEX 1
+#define TSC_4WIRE_Y_INDEX 2
+#define TSC_4WIRE_POST_INDEX 3
+#define TSC_4WIRE_LEAVE 4
+
+#define MX25_TSC_DEF_THRESHOLD 80
+#define TSC_MAX_SAMPLES 16
+
+#define MX25_TSC_REPEAT_WAIT 14
+
+enum mx25_adc_configurations {
+ MX25_CFG_PRECHARGE = 0,
+ MX25_CFG_TOUCH_DETECT,
+ MX25_CFG_X_MEASUREMENT,
+ MX25_CFG_Y_MEASUREMENT,
+};
+
+#define MX25_PRECHARGE_VALUE (\
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_HIGH | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_IGS)
+
+#define MX25_TOUCH_DETECT_VALUE (\
+ MX25_ADCQ_CFG_YNLR | \
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_OFF | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_PENIACK)
+
+static void imx25_setup_queue_cfgs(struct mx25_tcq_priv *priv,
+ unsigned int settling_time)
+{
+ u32 precharge_cfg =
+ MX25_PRECHARGE_VALUE |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+ u32 touch_detect_cfg =
+ MX25_TOUCH_DETECT_VALUE |
+ MX25_ADCQ_CFG_NOS(1) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+
+ regmap_write(priv->core_regs, MX25_TSC_TICR, precharge_cfg);
+
+ /* PRECHARGE */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_PRECHARGE),
+ precharge_cfg);
+
+ /* TOUCH_DETECT */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_TOUCH_DETECT),
+ touch_detect_cfg);
+
+ /* X Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_X_MEASUREMENT),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_LOW |
+ MX25_ADCQ_CFG_XPUL_HIGH |
+ MX25_ADCQ_CFG_REFP_XP |
+ MX25_ADCQ_CFG_IN_YP |
+ MX25_ADCQ_CFG_REFN_XN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Y Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_Y_MEASUREMENT),
+ MX25_ADCQ_CFG_YNLR |
+ MX25_ADCQ_CFG_YPLL_HIGH |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_YP |
+ MX25_ADCQ_CFG_IN_XP |
+ MX25_ADCQ_CFG_REFN_YN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Enable the touch detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, touch_detect_cfg |
+ MX25_ADCQ_CFG_IGS);
+}
+
+static int imx25_setup_queue_4wire(struct mx25_tcq_priv *priv,
+ unsigned settling_time, int *items)
+{
+ imx25_setup_queue_cfgs(priv, settling_time);
+
+ /* Setup the conversion queue */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(1, MX25_CFG_TOUCH_DETECT) |
+ MX25_ADCQ_ITEM(2, MX25_CFG_X_MEASUREMENT) |
+ MX25_ADCQ_ITEM(3, MX25_CFG_Y_MEASUREMENT) |
+ MX25_ADCQ_ITEM(4, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(5, MX25_CFG_TOUCH_DETECT));
+
+ /* We measure X/Y with 'sample_count' number of samples and execute a
+ * touch detection twice, with 1 sample each */
+ priv->expected_samples = priv->sample_count * 2 + 2;
+ *items = 6;
+
+ return 0;
+}
+
+static void mx25_tcq_disable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK,
+ MX25_ADCQ_CR_PDMSK);
+}
+
+static void mx25_tcq_enable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, 0);
+}
+
+static void mx25_tcq_disable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ,
+ MX25_ADCQ_MR_FDRY_IRQ);
+}
+
+static void mx25_tcq_enable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, 0);
+}
+
+static void mx25_tcq_force_queue_start(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+}
+
+static void mx25_tcq_force_queue_stop(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS, 0);
+}
+
+static void mx25_tcq_fifo_reset(struct mx25_tcq_priv *priv)
+{
+ u32 tcqcr;
+
+ regmap_read(priv->regs, MX25_ADCQ_CR, &tcqcr);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST,
+ MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST, 0);
+ regmap_write(priv->regs, MX25_ADCQ_CR, tcqcr);
+}
+
+static void mx25_tcq_re_enable_touch_detection(struct mx25_tcq_priv *priv)
+{
+ /* stop the queue from looping */
+ mx25_tcq_force_queue_stop(priv);
+
+ /* for a clean touch detection, preload the X plane */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_PRECHARGE_VALUE);
+
+ /* waste some time now to pre-load the X plate to high voltage */
+ mx25_tcq_fifo_reset(priv);
+
+ /* re-enable the detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR,
+ MX25_TOUCH_DETECT_VALUE | MX25_ADCQ_CFG_IGS);
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_PD,
+ MX25_ADCQ_SR_PD);
+
+ /* enable the pen down event to be a source for the interrupt */
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_PD_IRQ, 0);
+
+ /* lets fire the next IRQ if someone touches the touchscreen */
+ mx25_tcq_enable_touch_irq(priv);
+}
+
+static int mx25_tcq_create_event_for_4wire(struct mx25_tcq_priv *priv,
+ u32 *sample_buf,
+ unsigned int samples)
+{
+ unsigned int x_pos = 0;
+ unsigned int y_pos = 0;
+ unsigned int touch_pre = 0;
+ unsigned int touch_post = 0;
+ unsigned int i;
+ int ret = 0;
+
+ for (i = 0; i < samples; i++) {
+ unsigned int index = MX25_ADCQ_FIFO_ID(sample_buf[i]);
+ unsigned int val = MX25_ADCQ_FIFO_DATA(sample_buf[i]);
+
+ switch (index) {
+ case 1:
+ touch_pre = val;
+ break;
+ case 2:
+ x_pos = val;
+ break;
+ case 3:
+ y_pos = val;
+ break;
+ case 5:
+ touch_post = val;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ if (ret == 0 && samples != 0) {
+ /*
+ * only if both touch measures are below a threshold,
+ * the position is valid
+ */
+ if (touch_pre < priv->pen_threshold &&
+ touch_post < priv->pen_threshold) {
+ /* valid samples, generate a report */
+ x_pos /= priv->sample_count;
+ y_pos /= priv->sample_count;
+ input_report_abs(priv->idev, ABS_X, x_pos);
+ input_report_abs(priv->idev, ABS_Y, y_pos);
+ input_report_key(priv->idev, BTN_TOUCH, 1);
+ input_sync(priv->idev);
+
+ /* get next sample */
+ mx25_tcq_enable_fifo_irq(priv);
+ } else if (touch_pre >= priv->pen_threshold &&
+ touch_post >= priv->pen_threshold) {
+ /*
+ * if both samples are invalid,
+ * generate a release report
+ */
+ input_report_key(priv->idev, BTN_TOUCH, 0);
+ input_sync(priv->idev);
+ mx25_tcq_re_enable_touch_detection(priv);
+ } else {
+ /*
+ * if only one of both touch measurements are
+ * below the threshold, still some bouncing
+ * happens. Take additional samples in this
+ * case to be sure
+ */
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+ }
+
+ return ret;
+}
+
+static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 sample_buf[TSC_MAX_SAMPLES];
+ unsigned int samples = 0;
+
+ /* read all samples */
+ while (1) {
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+ if (stats & MX25_ADCQ_SR_EMPT)
+ break;
+
+ if (samples < TSC_MAX_SAMPLES) {
+ regmap_read(priv->regs, MX25_ADCQ_FIFO,
+ &sample_buf[samples]);
+ ++samples;
+ } else {
+ u32 discarded;
+ /* discard samples */
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &discarded);
+ }
+ }
+
+ mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 stat;
+ int ret = IRQ_HANDLED;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
+
+ if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
+ mx25_tcq_fifo_reset(priv);
+
+ if (stat & MX25_ADCQ_SR_PD) {
+ mx25_tcq_disable_touch_irq(priv);
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+
+ if (stat & MX25_ADCQ_SR_FDRY) {
+ mx25_tcq_disable_fifo_irq(priv);
+ ret = IRQ_WAKE_THREAD;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_PD | MX25_ADCQ_SR_EOQ,
+ MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR |
+ MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
+ MX25_ADCQ_SR_EOQ);
+
+ return ret;
+}
+
+/* configure the statemachine for a 4-wire touchscreen */
+static int mx25_tcq_init(struct mx25_tcq_priv *priv)
+{
+ u32 tgcr;
+ unsigned int ipg_div;
+ unsigned int adc_period;
+ unsigned int debounce_cnt;
+ unsigned int settling_time;
+ int itemct;
+ int ret;
+
+ regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
+ ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
+ adc_period = clk_get_rate(priv->clk) / (ipg_div * 2 + 2);
+ debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
+ settling_time = DIV_ROUND_UP(priv->settling_time, adc_period);
+
+ /* Reset */
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST, 0);
+
+ /* up to 128 * 8 ADC clocks are possible */
+ if (debounce_cnt > 127)
+ debounce_cnt = 127;
+
+ ret = imx25_setup_queue_4wire(priv, settling_time, &itemct);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_LITEMID_MASK | MX25_ADCQ_CR_WMRK_MASK,
+ MX25_ADCQ_CR_LITEMID(itemct - 1) |
+ MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
+
+ /* setup debounce count */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
+ MX25_TGCR_PDBTIME_MASK,
+ MX25_TGCR_PDBTIME(debounce_cnt));
+
+ /* enable debounce */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
+ MX25_TGCR_PDBEN);
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
+ MX25_TGCR_PDEN);
+
+ /* enable the engine on demand */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_MASK,
+ MX25_ADCQ_CR_QSM_FQS);
+
+ /* Enable repeat and repeat wait */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_RPT | MX25_ADCQ_CR_RWAIT_MASK,
+ MX25_ADCQ_CR_RPT |
+ MX25_ADCQ_CR_RWAIT(MX25_TSC_REPEAT_WAIT));
+
+ mx25_tcq_re_enable_touch_detection(priv);
+
+ return 0;
+}
+
+static int mx25_tcq_parse_dt(struct platform_device *pdev,
+ struct mx25_tcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ u32 wires;
+ int ret;
+
+ /* Setup defaults */
+ priv->pen_threshold = 500;
+ priv->sample_count = 3;
+ priv->pen_debounce = 1000000;
+ priv->settling_time = 250000;
+
+ ret = of_property_read_u32(np, "fsl,wires", &wires);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
+ return ret;
+ }
+
+ if (wires == 4) {
+ priv->mode = MX25_TS_4WIRE;
+ } else {
+ dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
+ return -EINVAL;
+ }
+
+ /* These are optional, we don't care about the return values */
+ of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
+ of_property_read_u32(np, "fsl,settling-time", &priv->settling_time);
+ of_property_read_u32(np, "fsl,pen-debounce", &priv->pen_debounce);
+
+ return 0;
+}
+
+static int mx25_tcq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct input_dev *idev;
+ struct mx25_tcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (!mem)
+ return -ENOMEM;
+
+ ret = mx25_tcq_parse_dt(pdev, priv);
+ if (ret)
+ return ret;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ return priv->irq;
+ }
+
+ idev = devm_input_allocate_device(dev);
+ if (!idev) {
+ dev_err(dev, "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ idev->name = mx25_tcq_name;
+ idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
+ input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
+
+ idev->id.bustype = BUS_HOST;
+
+ ret = input_register_device(idev);
+ if (ret) {
+ dev_err(dev, "Failed to register input device\n");
+ return ret;
+ }
+
+ priv->idev = idev;
+
+ priv->core_regs = tsadc->regs;
+ if (!priv->core_regs)
+ return -EINVAL;
+
+ priv->clk = tsadc->clk;
+ if (!priv->clk)
+ return -EINVAL;
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable ipg clock\n");
+ return ret;
+ }
+
+ ret = request_threaded_irq(priv->irq, mx25_tcq_irq, mx25_tcq_irq_thread,
+ IRQF_ONESHOT, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ goto err_clk_unprepare;
+ }
+
+ ret = mx25_tcq_init(priv);
+ if (ret) {
+ dev_err(dev, "Failed to init tcq\n");
+ goto error_free_irq;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+error_free_irq:
+ free_irq(priv->irq, priv);
+err_clk_unprepare:
+ clk_disable_unprepare(priv->clk);
+ return ret;
+}
+
+static int mx25_tcq_remove(struct platform_device *pdev)
+{
+ struct mx25_tcq_priv *priv = platform_get_drvdata(pdev);
+
+ free_irq(priv->irq, priv);
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct platform_driver mx25_tcq_driver = {
+ .driver = {
+ .name = "mx25-tcq",
+ .of_match_table = mx25_tcq_ids,
+ },
+ .probe = mx25_tcq_probe,
+ .remove = mx25_tcq_remove,
+};
+module_platform_driver(mx25_tcq_driver);
+
+MODULE_DESCRIPTION("TS input driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 4/6] input: touchscreen: imx25 tcq driver
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
This is a driver for the imx25 ADC/TSC module. It controls the
touchscreen conversion queue and creates a touchscreen input device.
The driver currently only supports 4 wire touchscreens. The driver uses
a simple conversion queue of precharge, touch detection, X measurement,
Y measurement, precharge and another touch detection.
This driver uses the regmap from the parent to setup some touch specific
settings in the core driver and setup a idle configuration with touch
detection.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
---
Notes:
Changes in v5:
- Fix signed/unsigned comparison
- Fix unused variable settling_time by putting it in the correct argument list
- Use continous conversion queue with the repeat feature and a proper
repeat-wait. Previously the touchscreen caused massive number of interrupts.
.../bindings/input/touchscreen/fsl-mx25-tcq.txt | 29 +
drivers/input/touchscreen/Kconfig | 6 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/fsl-imx25-tcq.c | 587 +++++++++++++++++++++
4 files changed, 623 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
new file mode 100644
index 000000000000..4214a99d197a
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -0,0 +1,29 @@
+Freescale mx25 TS conversion queue module
+
+mx25 touchscreen conversion queue module which controls the ADC unit of the
+mx25 for attached touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tcq".
+ - reg: Memory range of the device.
+ - interrupts: Should be the interrupt number associated with this module within
+ the tscadc unit (<0>).
+ - interrupt-parent: Should be a phandle to the tscadc unit.
+ - fsl,wires: Should be '<4>' or '<5>'
+
+Optional properties:
+ - fsl,pen-debounce: Pen debounce time.
+ - fsl,pen-threshold: Pen-down threshold for the touchscreen.
+ - fsl,settling-time: Settling time in nanoseconds.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tsc: tcq at 50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ };
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 58917525126e..f1534a0cd23f 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -748,6 +748,12 @@ config TOUCHSCREEN_USB_COMPOSITE
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MX25
+ tristate "Freescale i.MX25 touchscreen input driver"
+ depends on MFD_MX25_TSADC
+ help
+ Enable support for touchscreen connected to your i.MX25.
+
config TOUCHSCREEN_MC13783
tristate "Freescale MC13783 touchscreen input driver"
depends on MFD_MC13XXX
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 0242fea2102a..bbb55a69c33c 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o
diff --git a/drivers/input/touchscreen/fsl-imx25-tcq.c b/drivers/input/touchscreen/fsl-imx25-tcq.c
new file mode 100644
index 000000000000..2eb3bd00d56c
--- /dev/null
+++ b/drivers/input/touchscreen/fsl-imx25-tcq.c
@@ -0,0 +1,587 @@
+/*
+ * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
+ * Based on driver from 2011:
+ * Juergen Beisert, Pengutronix <kernel@pengutronix.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ *
+ * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <linux/clk.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static const char mx25_tcq_name[] = "mx25-tcq";
+
+enum mx25_tcq_mode {
+ MX25_TS_4WIRE,
+};
+
+struct mx25_tcq_priv {
+ struct regmap *regs;
+ struct regmap *core_regs;
+ struct input_dev *idev;
+ enum mx25_tcq_mode mode;
+ unsigned int pen_threshold;
+ unsigned int sample_count;
+ unsigned int expected_samples;
+ unsigned int pen_debounce;
+ unsigned int settling_time;
+ struct clk *clk;
+ int irq;
+};
+
+static struct regmap_config mx25_tcq_regconfig = {
+ .fast_io = true,
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static struct of_device_id mx25_tcq_ids[] = {
+ { .compatible = "fsl,imx25-tcq", },
+ { /* Sentinel */ }
+};
+
+#define TSC_4WIRE_PRE_INDEX 0
+#define TSC_4WIRE_X_INDEX 1
+#define TSC_4WIRE_Y_INDEX 2
+#define TSC_4WIRE_POST_INDEX 3
+#define TSC_4WIRE_LEAVE 4
+
+#define MX25_TSC_DEF_THRESHOLD 80
+#define TSC_MAX_SAMPLES 16
+
+#define MX25_TSC_REPEAT_WAIT 14
+
+enum mx25_adc_configurations {
+ MX25_CFG_PRECHARGE = 0,
+ MX25_CFG_TOUCH_DETECT,
+ MX25_CFG_X_MEASUREMENT,
+ MX25_CFG_Y_MEASUREMENT,
+};
+
+#define MX25_PRECHARGE_VALUE (\
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_HIGH | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_IGS)
+
+#define MX25_TOUCH_DETECT_VALUE (\
+ MX25_ADCQ_CFG_YNLR | \
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_OFF | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_PENIACK)
+
+static void imx25_setup_queue_cfgs(struct mx25_tcq_priv *priv,
+ unsigned int settling_time)
+{
+ u32 precharge_cfg =
+ MX25_PRECHARGE_VALUE |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+ u32 touch_detect_cfg =
+ MX25_TOUCH_DETECT_VALUE |
+ MX25_ADCQ_CFG_NOS(1) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time);
+
+ regmap_write(priv->core_regs, MX25_TSC_TICR, precharge_cfg);
+
+ /* PRECHARGE */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_PRECHARGE),
+ precharge_cfg);
+
+ /* TOUCH_DETECT */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_TOUCH_DETECT),
+ touch_detect_cfg);
+
+ /* X Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_X_MEASUREMENT),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_LOW |
+ MX25_ADCQ_CFG_XPUL_HIGH |
+ MX25_ADCQ_CFG_REFP_XP |
+ MX25_ADCQ_CFG_IN_YP |
+ MX25_ADCQ_CFG_REFN_XN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Y Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_Y_MEASUREMENT),
+ MX25_ADCQ_CFG_YNLR |
+ MX25_ADCQ_CFG_YPLL_HIGH |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_YP |
+ MX25_ADCQ_CFG_IN_XP |
+ MX25_ADCQ_CFG_REFN_YN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_time));
+
+ /* Enable the touch detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, touch_detect_cfg |
+ MX25_ADCQ_CFG_IGS);
+}
+
+static int imx25_setup_queue_4wire(struct mx25_tcq_priv *priv,
+ unsigned settling_time, int *items)
+{
+ imx25_setup_queue_cfgs(priv, settling_time);
+
+ /* Setup the conversion queue */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(1, MX25_CFG_TOUCH_DETECT) |
+ MX25_ADCQ_ITEM(2, MX25_CFG_X_MEASUREMENT) |
+ MX25_ADCQ_ITEM(3, MX25_CFG_Y_MEASUREMENT) |
+ MX25_ADCQ_ITEM(4, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(5, MX25_CFG_TOUCH_DETECT));
+
+ /* We measure X/Y with 'sample_count' number of samples and execute a
+ * touch detection twice, with 1 sample each */
+ priv->expected_samples = priv->sample_count * 2 + 2;
+ *items = 6;
+
+ return 0;
+}
+
+static void mx25_tcq_disable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK,
+ MX25_ADCQ_CR_PDMSK);
+}
+
+static void mx25_tcq_enable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, 0);
+}
+
+static void mx25_tcq_disable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ,
+ MX25_ADCQ_MR_FDRY_IRQ);
+}
+
+static void mx25_tcq_enable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, 0);
+}
+
+static void mx25_tcq_force_queue_start(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+}
+
+static void mx25_tcq_force_queue_stop(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS, 0);
+}
+
+static void mx25_tcq_fifo_reset(struct mx25_tcq_priv *priv)
+{
+ u32 tcqcr;
+
+ regmap_read(priv->regs, MX25_ADCQ_CR, &tcqcr);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST,
+ MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST, 0);
+ regmap_write(priv->regs, MX25_ADCQ_CR, tcqcr);
+}
+
+static void mx25_tcq_re_enable_touch_detection(struct mx25_tcq_priv *priv)
+{
+ /* stop the queue from looping */
+ mx25_tcq_force_queue_stop(priv);
+
+ /* for a clean touch detection, preload the X plane */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_PRECHARGE_VALUE);
+
+ /* waste some time now to pre-load the X plate to high voltage */
+ mx25_tcq_fifo_reset(priv);
+
+ /* re-enable the detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR,
+ MX25_TOUCH_DETECT_VALUE | MX25_ADCQ_CFG_IGS);
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_PD,
+ MX25_ADCQ_SR_PD);
+
+ /* enable the pen down event to be a source for the interrupt */
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_PD_IRQ, 0);
+
+ /* lets fire the next IRQ if someone touches the touchscreen */
+ mx25_tcq_enable_touch_irq(priv);
+}
+
+static int mx25_tcq_create_event_for_4wire(struct mx25_tcq_priv *priv,
+ u32 *sample_buf,
+ unsigned int samples)
+{
+ unsigned int x_pos = 0;
+ unsigned int y_pos = 0;
+ unsigned int touch_pre = 0;
+ unsigned int touch_post = 0;
+ unsigned int i;
+ int ret = 0;
+
+ for (i = 0; i < samples; i++) {
+ unsigned int index = MX25_ADCQ_FIFO_ID(sample_buf[i]);
+ unsigned int val = MX25_ADCQ_FIFO_DATA(sample_buf[i]);
+
+ switch (index) {
+ case 1:
+ touch_pre = val;
+ break;
+ case 2:
+ x_pos = val;
+ break;
+ case 3:
+ y_pos = val;
+ break;
+ case 5:
+ touch_post = val;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ if (ret == 0 && samples != 0) {
+ /*
+ * only if both touch measures are below a threshold,
+ * the position is valid
+ */
+ if (touch_pre < priv->pen_threshold &&
+ touch_post < priv->pen_threshold) {
+ /* valid samples, generate a report */
+ x_pos /= priv->sample_count;
+ y_pos /= priv->sample_count;
+ input_report_abs(priv->idev, ABS_X, x_pos);
+ input_report_abs(priv->idev, ABS_Y, y_pos);
+ input_report_key(priv->idev, BTN_TOUCH, 1);
+ input_sync(priv->idev);
+
+ /* get next sample */
+ mx25_tcq_enable_fifo_irq(priv);
+ } else if (touch_pre >= priv->pen_threshold &&
+ touch_post >= priv->pen_threshold) {
+ /*
+ * if both samples are invalid,
+ * generate a release report
+ */
+ input_report_key(priv->idev, BTN_TOUCH, 0);
+ input_sync(priv->idev);
+ mx25_tcq_re_enable_touch_detection(priv);
+ } else {
+ /*
+ * if only one of both touch measurements are
+ * below the threshold, still some bouncing
+ * happens. Take additional samples in this
+ * case to be sure
+ */
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+ }
+
+ return ret;
+}
+
+static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 sample_buf[TSC_MAX_SAMPLES];
+ unsigned int samples = 0;
+
+ /* read all samples */
+ while (1) {
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+ if (stats & MX25_ADCQ_SR_EMPT)
+ break;
+
+ if (samples < TSC_MAX_SAMPLES) {
+ regmap_read(priv->regs, MX25_ADCQ_FIFO,
+ &sample_buf[samples]);
+ ++samples;
+ } else {
+ u32 discarded;
+ /* discard samples */
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &discarded);
+ }
+ }
+
+ mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 stat;
+ int ret = IRQ_HANDLED;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
+
+ if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
+ mx25_tcq_fifo_reset(priv);
+
+ if (stat & MX25_ADCQ_SR_PD) {
+ mx25_tcq_disable_touch_irq(priv);
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+
+ if (stat & MX25_ADCQ_SR_FDRY) {
+ mx25_tcq_disable_fifo_irq(priv);
+ ret = IRQ_WAKE_THREAD;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_PD | MX25_ADCQ_SR_EOQ,
+ MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR |
+ MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
+ MX25_ADCQ_SR_EOQ);
+
+ return ret;
+}
+
+/* configure the statemachine for a 4-wire touchscreen */
+static int mx25_tcq_init(struct mx25_tcq_priv *priv)
+{
+ u32 tgcr;
+ unsigned int ipg_div;
+ unsigned int adc_period;
+ unsigned int debounce_cnt;
+ unsigned int settling_time;
+ int itemct;
+ int ret;
+
+ regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
+ ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
+ adc_period = clk_get_rate(priv->clk) / (ipg_div * 2 + 2);
+ debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
+ settling_time = DIV_ROUND_UP(priv->settling_time, adc_period);
+
+ /* Reset */
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST, 0);
+
+ /* up to 128 * 8 ADC clocks are possible */
+ if (debounce_cnt > 127)
+ debounce_cnt = 127;
+
+ ret = imx25_setup_queue_4wire(priv, settling_time, &itemct);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_LITEMID_MASK | MX25_ADCQ_CR_WMRK_MASK,
+ MX25_ADCQ_CR_LITEMID(itemct - 1) |
+ MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
+
+ /* setup debounce count */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
+ MX25_TGCR_PDBTIME_MASK,
+ MX25_TGCR_PDBTIME(debounce_cnt));
+
+ /* enable debounce */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
+ MX25_TGCR_PDBEN);
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
+ MX25_TGCR_PDEN);
+
+ /* enable the engine on demand */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_MASK,
+ MX25_ADCQ_CR_QSM_FQS);
+
+ /* Enable repeat and repeat wait */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_RPT | MX25_ADCQ_CR_RWAIT_MASK,
+ MX25_ADCQ_CR_RPT |
+ MX25_ADCQ_CR_RWAIT(MX25_TSC_REPEAT_WAIT));
+
+ mx25_tcq_re_enable_touch_detection(priv);
+
+ return 0;
+}
+
+static int mx25_tcq_parse_dt(struct platform_device *pdev,
+ struct mx25_tcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ u32 wires;
+ int ret;
+
+ /* Setup defaults */
+ priv->pen_threshold = 500;
+ priv->sample_count = 3;
+ priv->pen_debounce = 1000000;
+ priv->settling_time = 250000;
+
+ ret = of_property_read_u32(np, "fsl,wires", &wires);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
+ return ret;
+ }
+
+ if (wires == 4) {
+ priv->mode = MX25_TS_4WIRE;
+ } else {
+ dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
+ return -EINVAL;
+ }
+
+ /* These are optional, we don't care about the return values */
+ of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
+ of_property_read_u32(np, "fsl,settling-time", &priv->settling_time);
+ of_property_read_u32(np, "fsl,pen-debounce", &priv->pen_debounce);
+
+ return 0;
+}
+
+static int mx25_tcq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct input_dev *idev;
+ struct mx25_tcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (!mem)
+ return -ENOMEM;
+
+ ret = mx25_tcq_parse_dt(pdev, priv);
+ if (ret)
+ return ret;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ return priv->irq;
+ }
+
+ idev = devm_input_allocate_device(dev);
+ if (!idev) {
+ dev_err(dev, "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ idev->name = mx25_tcq_name;
+ idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
+ input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
+
+ idev->id.bustype = BUS_HOST;
+
+ ret = input_register_device(idev);
+ if (ret) {
+ dev_err(dev, "Failed to register input device\n");
+ return ret;
+ }
+
+ priv->idev = idev;
+
+ priv->core_regs = tsadc->regs;
+ if (!priv->core_regs)
+ return -EINVAL;
+
+ priv->clk = tsadc->clk;
+ if (!priv->clk)
+ return -EINVAL;
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable ipg clock\n");
+ return ret;
+ }
+
+ ret = request_threaded_irq(priv->irq, mx25_tcq_irq, mx25_tcq_irq_thread,
+ IRQF_ONESHOT, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ goto err_clk_unprepare;
+ }
+
+ ret = mx25_tcq_init(priv);
+ if (ret) {
+ dev_err(dev, "Failed to init tcq\n");
+ goto error_free_irq;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+error_free_irq:
+ free_irq(priv->irq, priv);
+err_clk_unprepare:
+ clk_disable_unprepare(priv->clk);
+ return ret;
+}
+
+static int mx25_tcq_remove(struct platform_device *pdev)
+{
+ struct mx25_tcq_priv *priv = platform_get_drvdata(pdev);
+
+ free_irq(priv->irq, priv);
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct platform_driver mx25_tcq_driver = {
+ .driver = {
+ .name = "mx25-tcq",
+ .of_match_table = mx25_tcq_ids,
+ },
+ .probe = mx25_tcq_probe,
+ .remove = mx25_tcq_remove,
+};
+module_platform_driver(mx25_tcq_driver);
+
+MODULE_DESCRIPTION("TS input driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 5/6] ARM: dts: imx25: Add TSC and ADC support
2015-01-24 14:01 ` Markus Pargmann
(?)
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lee Jones,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, Markus Pargmann
From: Denis Carikli <denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Denis Carikli <denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
arch/arm/boot/dts/imx25.dtsi | 30 +++++++++++++++++++++++++++---
1 file changed, 27 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi
index 58d3c3cf2923..73ebc63353ef 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/imx25.dtsi
@@ -265,13 +265,37 @@
status = "disabled";
};
- tsc: tsc@50030000 {
- compatible = "fsl,imx25-adc", "fsl,imx21-tsc";
- reg = <0x50030000 0x4000>;
+ tscadc: tscadc@50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
interrupts = <46>;
clocks = <&clks 119>;
clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
status = "disabled";
+
+ adc: adc@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ status = "disabled";
+ };
};
ssi1: ssi@50034000 {
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 5/6] ARM: dts: imx25: Add TSC and ADC support
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
From: Denis Carikli <denis@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
arch/arm/boot/dts/imx25.dtsi | 30 +++++++++++++++++++++++++++---
1 file changed, 27 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi
index 58d3c3cf2923..73ebc63353ef 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/imx25.dtsi
@@ -265,13 +265,37 @@
status = "disabled";
};
- tsc: tsc@50030000 {
- compatible = "fsl,imx25-adc", "fsl,imx21-tsc";
- reg = <0x50030000 0x4000>;
+ tscadc: tscadc@50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
interrupts = <46>;
clocks = <&clks 119>;
clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
status = "disabled";
+
+ adc: adc@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ status = "disabled";
+ };
};
ssi1: ssi@50034000 {
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 5/6] ARM: dts: imx25: Add TSC and ADC support
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
From: Denis Carikli <denis@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
arch/arm/boot/dts/imx25.dtsi | 30 +++++++++++++++++++++++++++---
1 file changed, 27 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi
index 58d3c3cf2923..73ebc63353ef 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/imx25.dtsi
@@ -265,13 +265,37 @@
status = "disabled";
};
- tsc: tsc at 50030000 {
- compatible = "fsl,imx25-adc", "fsl,imx21-tsc";
- reg = <0x50030000 0x4000>;
+ tscadc: tscadc at 50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
interrupts = <46>;
clocks = <&clks 119>;
clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
status = "disabled";
+
+ adc: adc at 50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ tsc: tcq at 50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ status = "disabled";
+ };
};
ssi1: ssi at 50034000 {
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 6/6] ARM: imx_v4_v5_defconfig: Add I.MX25 Touchscreen controller and ADC support.
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-24 14:01 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Markus Pargmann
From: Denis Carikli <denis@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
arch/arm/configs/imx_v4_v5_defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index e6b0007355f8..e1bda0136f6c 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -89,6 +89,7 @@ CONFIG_KEYBOARD_IMX=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
+CONFIG_TOUCHSCREEN_MX25=y
CONFIG_TOUCHSCREEN_MC13783=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=m
@@ -108,6 +109,7 @@ CONFIG_HWMON=m
CONFIG_SENSORS_MC13783_ADC=m
CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y
+CONFIG_MFD_MX25_TSADC=y
CONFIG_MFD_MC13XXX_SPI=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -173,6 +175,8 @@ CONFIG_DMADEVICES=y
CONFIG_IMX_SDMA=y
CONFIG_IMX_DMA=y
# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_FSL_MX25_ADC=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 6/6] ARM: imx_v4_v5_defconfig: Add I.MX25 Touchscreen controller and ADC support.
@ 2015-01-24 14:01 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-24 14:01 UTC (permalink / raw)
To: linux-arm-kernel
From: Denis Carikli <denis@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
---
arch/arm/configs/imx_v4_v5_defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index e6b0007355f8..e1bda0136f6c 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -89,6 +89,7 @@ CONFIG_KEYBOARD_IMX=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
+CONFIG_TOUCHSCREEN_MX25=y
CONFIG_TOUCHSCREEN_MC13783=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=m
@@ -108,6 +109,7 @@ CONFIG_HWMON=m
CONFIG_SENSORS_MC13783_ADC=m
CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y
+CONFIG_MFD_MX25_TSADC=y
CONFIG_MFD_MC13XXX_SPI=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -173,6 +175,8 @@ CONFIG_DMADEVICES=y
CONFIG_IMX_SDMA=y
CONFIG_IMX_DMA=y
# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_FSL_MX25_ADC=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-24 14:01 ` Markus Pargmann
@ 2015-01-27 20:30 ` Jonathan Cameron
-1 siblings, 0 replies; 50+ messages in thread
From: Jonathan Cameron @ 2015-01-27 20:30 UTC (permalink / raw)
To: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Fabio Estevam, Peter Meerwald, Hartmut Knaack
Cc: Denis Carikli, Eric Bénard, Sascha Hauer, linux-arm-kernel,
Lee Jones, linux-input, linux-iio, Lars-Peter Clausen,
devicetree, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala
On 24/01/15 14:01, Markus Pargmann wrote:
> This is a conversion queue driver for the mx25 SoC. It uses the central
> ADC which is used by two seperate independent queues. This driver
> prepares different conversion configurations for each possible input.
> For a conversion it creates a conversionqueue of one item with the
> correct configuration for the chosen channel. It then executes the queue
> once and disables the conversion queue afterwards.
>
> The reference voltages are configurable through devicetree subnodes,
> depending on the connections of the ADC inputs.
>
> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> Signed-off-by: Denis Carikli <denis@eukrea.com>
A couple of queries inline.
> ---
>
> Notes:
> Changes in v5:
> - Fixed locking
> - Removed module owner
>
> .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
> drivers/iio/adc/Kconfig | 7 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
> include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
> 5 files changed, 439 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> new file mode 100644
> index 000000000000..d55b6b751349
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> @@ -0,0 +1,51 @@
> +Freescale i.MX25 ADC GCQ device
> +
> +This is a generic conversion queue device that can convert any of the
> +analog inputs using the ADC unit of the i.MX25.
> +
> +Required properties:
> + - compatible: Should be "fsl,imx25-gcq".
> + - reg: Should be the register range of the module.
> + - interrupts: Should be the interrupt number of the module.
> + Typically this is <1>.
> + - interrupt-parent: phandle to the tsadc module of the i.MX25.
> + - #address-cells: Should be <1> (setting for the subnodes)
> + - #size-cells: Should be <0> (setting for the subnodes)
> +
> +Optional properties:
> + - vref-supply: The regulator supplying the ADC reference voltage.
> + Required when at least one subnode uses the external reference.
> +
> +Sub-nodes:
> +Optionally you can define subnodes which define the reference voltage
> +for the analog inputs.
> +
> +Required properties for subnodes:
> + - reg: Should be the number of the analog input.
> + 0: xp
> + 1: yp
> + 2: xn
> + 3: yn
> + 4: wiper
> + 5: inaux0
> + 6: inaux1
> + 7: inaux2
> + - fsl,adc-ref: specifies the reference input as defined in
> + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
> +
> +Example:
> +
> + adc: adc@50030800 {
> + compatible = "fsl,imx25-gcq";
> + reg = <0x50030800 0x60>;
> + interrupt-parent = <&tscadc>;
> + interrupts = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + inaux@5 {
> + reg = <5>;
> + fsl,adc-ref = <MX25_ADC_REF_INT>;
> + };
> + };
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 0f79e4725763..fccbb4bf44cc 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -143,6 +143,13 @@ config EXYNOS_ADC
> of SoCs for drivers such as the touchscreen and hwmon to use to share
> this resource.
>
> +config FSL_MX25_ADC
> + tristate "Freescale MX25 ADC driver"
> + depends on MFD_MX25_TSADC
> + help
> + Generic Conversion Queue driver used for general purpose ADC in the
> + MX25. This driver supports single measurements using the MX25 ADC.
> +
> config LP8788_ADC
> tristate "LP8788 ADC driver"
> depends on MFD_LP8788
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 701fdb7c96aa..acab8d956371 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
> obj-$(CONFIG_AT91_ADC) += at91_adc.o
> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> obj-$(CONFIG_MAX1027) += max1027.o
> obj-$(CONFIG_MAX1363) += max1363.o
> diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> new file mode 100644
> index 000000000000..c1ac5af41ec5
> --- /dev/null
> +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> @@ -0,0 +1,369 @@
> +/*
> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + *
> + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> + * connected to the imx25 ADC.
> + */
> +
> +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> +#include <linux/clk.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/imx25-tsadc.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +
> +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> +
> +enum mx25_gcq_cfgs {
> + MX25_CFG_XP = 0,
> + MX25_CFG_YP,
> + MX25_CFG_XN,
> + MX25_CFG_YN,
> + MX25_CFG_WIPER,
> + MX25_CFG_INAUX0,
> + MX25_CFG_INAUX1,
> + MX25_CFG_INAUX2,
> + MX25_NUM_CFGS,
> +};
> +
> +struct mx25_gcq_priv {
> + struct regmap *regs;
> + struct completion completed;
> + unsigned int settling_time;
> + struct clk *clk;
> + int irq;
> + struct regulator *ext_vref;
> + u32 channel_vref_mv[MX25_NUM_CFGS];
> +};
> +
> +#define MX25_CQG_CHAN(chan, id) {\
> + .type = IIO_VOLTAGE,\
> + .indexed = 1,\
> + .channel = chan,\
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> + .datasheet_name = id,\
> +}
> +
> +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> + MX25_CQG_CHAN(0, "xp"),
> + MX25_CQG_CHAN(1, "yp"),
> + MX25_CQG_CHAN(2, "xn"),
> + MX25_CQG_CHAN(3, "yn"),
> + MX25_CQG_CHAN(4, "wiper"),
> + MX25_CQG_CHAN(5, "inaux0"),
> + MX25_CQG_CHAN(6, "inaux1"),
> + MX25_CQG_CHAN(7, "inaux2"),
> +};
> +
> +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
> +{
> + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
> + MX25_ADCQ_MR_EOQ_IRQ);
> +}
> +
> +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
> +{
> + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> + MX25_ADCQ_MR_EOQ_IRQ, 0);
> +}
> +
> +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> +{
> + struct mx25_gcq_priv *priv = data;
> + u32 stats;
> +
> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> +
> + if (stats & MX25_ADCQ_SR_EOQ) {
> + mx25_gcq_disable_eoq(priv);
> + complete(&priv->completed);
> + }
> +
> + /* Disable conversion queue run */
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> +
> + /* Acknowledge all possible irqs */
> + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val,
> + int *val2, long mask)
> +{
> + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> + long timeout;
> + u32 data;
> + int ret = 0;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + mutex_lock(&indio_dev->mlock);
> +
> + /* Setup the configuration we want to use */
> + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> + MX25_ADCQ_ITEM(0, chan->channel));
> +
> + mx25_gcq_enable_eoq(priv);
> +
> + /* Trigger queue for one run */
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> + MX25_ADCQ_CR_FQS);
> +
> + timeout = wait_for_completion_interruptible_timeout(
> + &priv->completed, MX25_GCQ_TIMEOUT);
> + if (timeout < 0) {
> + dev_err(&indio_dev->dev,
> + "ADC wait for measurement failed\n");
> + ret = timeout;
> + goto info_raw_out;
> + } else if (timeout == 0) {
> + dev_err(&indio_dev->dev, "ADC timed out\n");
> + ret = -ETIMEDOUT;
> + goto info_raw_out;
> + }
> +
> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> +
> + *val = MX25_ADCQ_FIFO_DATA(data);
> + ret = IIO_VAL_INT;
> +info_raw_out:
Having this label and exit path in the middle is ugly.
Perhaps break out this case statement content as a separate function?
> + mutex_unlock(&indio_dev->mlock);
> +
> + return ret;
> +
> + case IIO_CHAN_INFO_SCALE:
> + *val = priv->channel_vref_mv[chan->channel];
> + *val2 = 12;
> + return IIO_VAL_FRACTIONAL_LOG2;
> +
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static const struct iio_info mx25_gcq_iio_info = {
> + .read_raw = mx25_gcq_read_raw,
> +};
> +
> +static const struct regmap_config mx25_gcq_regconfig = {
> + .max_register = 0x5c,
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> +};
> +
> +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> + struct mx25_gcq_priv *priv)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct device_node *child;
> + struct device *dev = &pdev->dev;
> + int ret, i;
> +
> + /*
> + * Setup all configurations registers with a default conversion
> + * configuration for each input
> + */
> + for (i = 0; i < MX25_NUM_CFGS; ++i)
> + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> + MX25_ADCQ_CFG_YPLL_OFF |
> + MX25_ADCQ_CFG_XNUR_OFF |
> + MX25_ADCQ_CFG_XPUL_OFF |
> + MX25_ADCQ_CFG_REFP_INT |
> + (i << 4) |
Again, given all the definitions i'd expect the shift to
be a defined constant as well. Perhaps even a macro taking
i as an arguement.
> + MX25_ADCQ_CFG_REFN_NGND2);
> +
> + for_each_child_of_node(np, child) {
> + u32 reg;
> + u32 refp;
> + u32 adc_ref;
> +
> + ret = of_property_read_u32(child, "reg", ®);
> + if (ret) {
> + dev_err(dev, "Failed to get reg property\n");
> + return ret;
> + }
> +
> + if (reg >= MX25_NUM_CFGS) {
> + dev_err(dev,
> + "reg value is greater than the number of available configuration registers\n");
> + return -EINVAL;
> + }
> +
> + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
> + if (ret) {
> + dev_err(dev, "Failed to get fsl,adc-ref property\n");
> + return ret;
> + }
> +
> + if (adc_ref != MX25_ADC_REF_INT &&
> + adc_ref != MX25_ADC_REF_EXT) {
> + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
> + adc_ref);
> + return -EINVAL;
> + }
> +
> + switch (adc_ref) {
> + case MX25_ADC_REF_EXT:
> + if (IS_ERR_OR_NULL(priv->ext_vref)) {
> + dev_err(dev,
> + "No regulator found for the external vref\n");
> + return -EINVAL;
> + }
> + priv->channel_vref_mv[reg] =
> + regulator_get_voltage(priv->ext_vref);
> + refp = MX25_ADCQ_CFG_REFP_EXT;
> + break;
> + case MX25_ADC_REF_INT:
> + priv->channel_vref_mv[reg] = 2500;
> + refp = MX25_ADCQ_CFG_REFP_INT;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> + MX25_ADCQ_CFG_REFP_MASK |
> + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
> + (MX25_ADCQ_CFG_REFN_NGND << 2));
It's a little inconsistent to define constants for the masks, but not
the shifts. Particularly given these constants are already shifted in
their definitions... Is that a bug?
> + }
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> +
> + regmap_write(priv->regs, MX25_ADCQ_CR,
> + MX25_ADCQ_CR_PDMSK |
> + MX25_ADCQ_CR_QSM_FQS);
> +
> + return 0;
> +}
> +
> +static int mx25_gcq_probe(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev;
> + struct mx25_gcq_priv *priv;
> + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + void __iomem *mem;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + priv = iio_priv(indio_dev);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + mem = devm_ioremap_resource(dev, res);
> + if (!mem)
> + return -ENOMEM;
> +
> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> + if (IS_ERR(priv->regs)) {
> + dev_err(dev, "Failed to initialize regmap\n");
> + return PTR_ERR(priv->regs);
> + }
> +
> + init_completion(&priv->completed);
> +
> + /* Optional external regulator */
> + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> + ret = regulator_enable(priv->ext_vref);
> + if (ret)
> + return ret;
> + }
> +
> + ret = mx25_gcq_setup_cfgs(pdev, priv);
> + if (ret)
> + return ret;
> +
> + priv->clk = tsadc->clk;
> + ret = clk_prepare_enable(priv->clk);
> + if (ret) {
> + dev_err(dev, "Failed to enable clock\n");
> + return ret;
> + }
> +
> + priv->irq = platform_get_irq(pdev, 0);
> + if (priv->irq <= 0) {
> + dev_err(dev, "Failed to get IRQ\n");
> + ret = priv->irq;
> + goto err_clk_unprepare;
> + }
> +
> + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
> + if (ret) {
> + dev_err(dev, "Failed requesting IRQ\n");
> + goto err_clk_unprepare;
> + }
> +
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->channels = mx25_gcq_channels;
> + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
> + indio_dev->info = &mx25_gcq_iio_info;
> +
> + ret = iio_device_register(indio_dev);
> + if (ret) {
> + dev_err(dev, "Failed to register iio device\n");
> + goto err_irq_free;
> + }
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return 0;
> +
> +err_irq_free:
> + free_irq(priv->irq, (void *)priv);
> +err_clk_unprepare:
> + clk_disable_unprepare(priv->clk);
> + return ret;
> +}
> +
> +static int mx25_gcq_remove(struct platform_device *pdev)
> +{
> + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
> + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
> +
> + iio_device_unregister(indio_dev);
> + free_irq(priv->irq, priv);
> + clk_disable_unprepare(priv->clk);
> +
> + return 0;
> +}
> +
> +static struct of_device_id mx25_gcq_ids[] = {
> + { .compatible = "fsl,imx25-gcq", },
> + { /* Sentinel */ }
> +};
> +
> +static struct platform_driver mx25_gcq_driver = {
> + .driver = {
> + .name = "mx25-gcq",
> + .of_match_table = mx25_gcq_ids,
> + },
> + .probe = mx25_gcq_probe,
> + .remove = mx25_gcq_remove,
> +};
> +module_platform_driver(mx25_gcq_driver);
> +
> +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
> +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> new file mode 100644
> index 000000000000..486dce735ac9
> --- /dev/null
> +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> @@ -0,0 +1,11 @@
> +/*
> + * This header provides constants for configuring the I.MX25 ADC
> + */
> +
> +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> +
> +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
> +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
Seems to me that this could be dealt with using a boolean property.
Afterall, we need to get a reference from somewhere, so if it isn't
internal it must be external?
I'm far from a device tree expert however, so perhaps this is the
preferred method.
> +
> +#endif
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-27 20:30 ` Jonathan Cameron
0 siblings, 0 replies; 50+ messages in thread
From: Jonathan Cameron @ 2015-01-27 20:30 UTC (permalink / raw)
To: linux-arm-kernel
On 24/01/15 14:01, Markus Pargmann wrote:
> This is a conversion queue driver for the mx25 SoC. It uses the central
> ADC which is used by two seperate independent queues. This driver
> prepares different conversion configurations for each possible input.
> For a conversion it creates a conversionqueue of one item with the
> correct configuration for the chosen channel. It then executes the queue
> once and disables the conversion queue afterwards.
>
> The reference voltages are configurable through devicetree subnodes,
> depending on the connections of the ADC inputs.
>
> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> Signed-off-by: Denis Carikli <denis@eukrea.com>
A couple of queries inline.
> ---
>
> Notes:
> Changes in v5:
> - Fixed locking
> - Removed module owner
>
> .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
> drivers/iio/adc/Kconfig | 7 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
> include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
> 5 files changed, 439 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> new file mode 100644
> index 000000000000..d55b6b751349
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> @@ -0,0 +1,51 @@
> +Freescale i.MX25 ADC GCQ device
> +
> +This is a generic conversion queue device that can convert any of the
> +analog inputs using the ADC unit of the i.MX25.
> +
> +Required properties:
> + - compatible: Should be "fsl,imx25-gcq".
> + - reg: Should be the register range of the module.
> + - interrupts: Should be the interrupt number of the module.
> + Typically this is <1>.
> + - interrupt-parent: phandle to the tsadc module of the i.MX25.
> + - #address-cells: Should be <1> (setting for the subnodes)
> + - #size-cells: Should be <0> (setting for the subnodes)
> +
> +Optional properties:
> + - vref-supply: The regulator supplying the ADC reference voltage.
> + Required when at least one subnode uses the external reference.
> +
> +Sub-nodes:
> +Optionally you can define subnodes which define the reference voltage
> +for the analog inputs.
> +
> +Required properties for subnodes:
> + - reg: Should be the number of the analog input.
> + 0: xp
> + 1: yp
> + 2: xn
> + 3: yn
> + 4: wiper
> + 5: inaux0
> + 6: inaux1
> + 7: inaux2
> + - fsl,adc-ref: specifies the reference input as defined in
> + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
> +
> +Example:
> +
> + adc: adc at 50030800 {
> + compatible = "fsl,imx25-gcq";
> + reg = <0x50030800 0x60>;
> + interrupt-parent = <&tscadc>;
> + interrupts = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + inaux at 5 {
> + reg = <5>;
> + fsl,adc-ref = <MX25_ADC_REF_INT>;
> + };
> + };
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 0f79e4725763..fccbb4bf44cc 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -143,6 +143,13 @@ config EXYNOS_ADC
> of SoCs for drivers such as the touchscreen and hwmon to use to share
> this resource.
>
> +config FSL_MX25_ADC
> + tristate "Freescale MX25 ADC driver"
> + depends on MFD_MX25_TSADC
> + help
> + Generic Conversion Queue driver used for general purpose ADC in the
> + MX25. This driver supports single measurements using the MX25 ADC.
> +
> config LP8788_ADC
> tristate "LP8788 ADC driver"
> depends on MFD_LP8788
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 701fdb7c96aa..acab8d956371 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
> obj-$(CONFIG_AT91_ADC) += at91_adc.o
> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> obj-$(CONFIG_MAX1027) += max1027.o
> obj-$(CONFIG_MAX1363) += max1363.o
> diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> new file mode 100644
> index 000000000000..c1ac5af41ec5
> --- /dev/null
> +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> @@ -0,0 +1,369 @@
> +/*
> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + *
> + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> + * connected to the imx25 ADC.
> + */
> +
> +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> +#include <linux/clk.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/mfd/imx25-tsadc.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +
> +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> +
> +enum mx25_gcq_cfgs {
> + MX25_CFG_XP = 0,
> + MX25_CFG_YP,
> + MX25_CFG_XN,
> + MX25_CFG_YN,
> + MX25_CFG_WIPER,
> + MX25_CFG_INAUX0,
> + MX25_CFG_INAUX1,
> + MX25_CFG_INAUX2,
> + MX25_NUM_CFGS,
> +};
> +
> +struct mx25_gcq_priv {
> + struct regmap *regs;
> + struct completion completed;
> + unsigned int settling_time;
> + struct clk *clk;
> + int irq;
> + struct regulator *ext_vref;
> + u32 channel_vref_mv[MX25_NUM_CFGS];
> +};
> +
> +#define MX25_CQG_CHAN(chan, id) {\
> + .type = IIO_VOLTAGE,\
> + .indexed = 1,\
> + .channel = chan,\
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> + .datasheet_name = id,\
> +}
> +
> +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> + MX25_CQG_CHAN(0, "xp"),
> + MX25_CQG_CHAN(1, "yp"),
> + MX25_CQG_CHAN(2, "xn"),
> + MX25_CQG_CHAN(3, "yn"),
> + MX25_CQG_CHAN(4, "wiper"),
> + MX25_CQG_CHAN(5, "inaux0"),
> + MX25_CQG_CHAN(6, "inaux1"),
> + MX25_CQG_CHAN(7, "inaux2"),
> +};
> +
> +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
> +{
> + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
> + MX25_ADCQ_MR_EOQ_IRQ);
> +}
> +
> +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
> +{
> + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> + MX25_ADCQ_MR_EOQ_IRQ, 0);
> +}
> +
> +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> +{
> + struct mx25_gcq_priv *priv = data;
> + u32 stats;
> +
> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> +
> + if (stats & MX25_ADCQ_SR_EOQ) {
> + mx25_gcq_disable_eoq(priv);
> + complete(&priv->completed);
> + }
> +
> + /* Disable conversion queue run */
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> +
> + /* Acknowledge all possible irqs */
> + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val,
> + int *val2, long mask)
> +{
> + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> + long timeout;
> + u32 data;
> + int ret = 0;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + mutex_lock(&indio_dev->mlock);
> +
> + /* Setup the configuration we want to use */
> + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> + MX25_ADCQ_ITEM(0, chan->channel));
> +
> + mx25_gcq_enable_eoq(priv);
> +
> + /* Trigger queue for one run */
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> + MX25_ADCQ_CR_FQS);
> +
> + timeout = wait_for_completion_interruptible_timeout(
> + &priv->completed, MX25_GCQ_TIMEOUT);
> + if (timeout < 0) {
> + dev_err(&indio_dev->dev,
> + "ADC wait for measurement failed\n");
> + ret = timeout;
> + goto info_raw_out;
> + } else if (timeout == 0) {
> + dev_err(&indio_dev->dev, "ADC timed out\n");
> + ret = -ETIMEDOUT;
> + goto info_raw_out;
> + }
> +
> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> +
> + *val = MX25_ADCQ_FIFO_DATA(data);
> + ret = IIO_VAL_INT;
> +info_raw_out:
Having this label and exit path in the middle is ugly.
Perhaps break out this case statement content as a separate function?
> + mutex_unlock(&indio_dev->mlock);
> +
> + return ret;
> +
> + case IIO_CHAN_INFO_SCALE:
> + *val = priv->channel_vref_mv[chan->channel];
> + *val2 = 12;
> + return IIO_VAL_FRACTIONAL_LOG2;
> +
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static const struct iio_info mx25_gcq_iio_info = {
> + .read_raw = mx25_gcq_read_raw,
> +};
> +
> +static const struct regmap_config mx25_gcq_regconfig = {
> + .max_register = 0x5c,
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> +};
> +
> +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> + struct mx25_gcq_priv *priv)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct device_node *child;
> + struct device *dev = &pdev->dev;
> + int ret, i;
> +
> + /*
> + * Setup all configurations registers with a default conversion
> + * configuration for each input
> + */
> + for (i = 0; i < MX25_NUM_CFGS; ++i)
> + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> + MX25_ADCQ_CFG_YPLL_OFF |
> + MX25_ADCQ_CFG_XNUR_OFF |
> + MX25_ADCQ_CFG_XPUL_OFF |
> + MX25_ADCQ_CFG_REFP_INT |
> + (i << 4) |
Again, given all the definitions i'd expect the shift to
be a defined constant as well. Perhaps even a macro taking
i as an arguement.
> + MX25_ADCQ_CFG_REFN_NGND2);
> +
> + for_each_child_of_node(np, child) {
> + u32 reg;
> + u32 refp;
> + u32 adc_ref;
> +
> + ret = of_property_read_u32(child, "reg", ®);
> + if (ret) {
> + dev_err(dev, "Failed to get reg property\n");
> + return ret;
> + }
> +
> + if (reg >= MX25_NUM_CFGS) {
> + dev_err(dev,
> + "reg value is greater than the number of available configuration registers\n");
> + return -EINVAL;
> + }
> +
> + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
> + if (ret) {
> + dev_err(dev, "Failed to get fsl,adc-ref property\n");
> + return ret;
> + }
> +
> + if (adc_ref != MX25_ADC_REF_INT &&
> + adc_ref != MX25_ADC_REF_EXT) {
> + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
> + adc_ref);
> + return -EINVAL;
> + }
> +
> + switch (adc_ref) {
> + case MX25_ADC_REF_EXT:
> + if (IS_ERR_OR_NULL(priv->ext_vref)) {
> + dev_err(dev,
> + "No regulator found for the external vref\n");
> + return -EINVAL;
> + }
> + priv->channel_vref_mv[reg] =
> + regulator_get_voltage(priv->ext_vref);
> + refp = MX25_ADCQ_CFG_REFP_EXT;
> + break;
> + case MX25_ADC_REF_INT:
> + priv->channel_vref_mv[reg] = 2500;
> + refp = MX25_ADCQ_CFG_REFP_INT;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> + MX25_ADCQ_CFG_REFP_MASK |
> + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
> + (MX25_ADCQ_CFG_REFN_NGND << 2));
It's a little inconsistent to define constants for the masks, but not
the shifts. Particularly given these constants are already shifted in
their definitions... Is that a bug?
> + }
> + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> +
> + regmap_write(priv->regs, MX25_ADCQ_CR,
> + MX25_ADCQ_CR_PDMSK |
> + MX25_ADCQ_CR_QSM_FQS);
> +
> + return 0;
> +}
> +
> +static int mx25_gcq_probe(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev;
> + struct mx25_gcq_priv *priv;
> + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + void __iomem *mem;
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + priv = iio_priv(indio_dev);
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + mem = devm_ioremap_resource(dev, res);
> + if (!mem)
> + return -ENOMEM;
> +
> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> + if (IS_ERR(priv->regs)) {
> + dev_err(dev, "Failed to initialize regmap\n");
> + return PTR_ERR(priv->regs);
> + }
> +
> + init_completion(&priv->completed);
> +
> + /* Optional external regulator */
> + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> + ret = regulator_enable(priv->ext_vref);
> + if (ret)
> + return ret;
> + }
> +
> + ret = mx25_gcq_setup_cfgs(pdev, priv);
> + if (ret)
> + return ret;
> +
> + priv->clk = tsadc->clk;
> + ret = clk_prepare_enable(priv->clk);
> + if (ret) {
> + dev_err(dev, "Failed to enable clock\n");
> + return ret;
> + }
> +
> + priv->irq = platform_get_irq(pdev, 0);
> + if (priv->irq <= 0) {
> + dev_err(dev, "Failed to get IRQ\n");
> + ret = priv->irq;
> + goto err_clk_unprepare;
> + }
> +
> + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
> + if (ret) {
> + dev_err(dev, "Failed requesting IRQ\n");
> + goto err_clk_unprepare;
> + }
> +
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->channels = mx25_gcq_channels;
> + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
> + indio_dev->info = &mx25_gcq_iio_info;
> +
> + ret = iio_device_register(indio_dev);
> + if (ret) {
> + dev_err(dev, "Failed to register iio device\n");
> + goto err_irq_free;
> + }
> +
> + platform_set_drvdata(pdev, priv);
> +
> + return 0;
> +
> +err_irq_free:
> + free_irq(priv->irq, (void *)priv);
> +err_clk_unprepare:
> + clk_disable_unprepare(priv->clk);
> + return ret;
> +}
> +
> +static int mx25_gcq_remove(struct platform_device *pdev)
> +{
> + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
> + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
> +
> + iio_device_unregister(indio_dev);
> + free_irq(priv->irq, priv);
> + clk_disable_unprepare(priv->clk);
> +
> + return 0;
> +}
> +
> +static struct of_device_id mx25_gcq_ids[] = {
> + { .compatible = "fsl,imx25-gcq", },
> + { /* Sentinel */ }
> +};
> +
> +static struct platform_driver mx25_gcq_driver = {
> + .driver = {
> + .name = "mx25-gcq",
> + .of_match_table = mx25_gcq_ids,
> + },
> + .probe = mx25_gcq_probe,
> + .remove = mx25_gcq_remove,
> +};
> +module_platform_driver(mx25_gcq_driver);
> +
> +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
> +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> new file mode 100644
> index 000000000000..486dce735ac9
> --- /dev/null
> +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> @@ -0,0 +1,11 @@
> +/*
> + * This header provides constants for configuring the I.MX25 ADC
> + */
> +
> +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> +
> +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
> +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
Seems to me that this could be dealt with using a boolean property.
Afterall, we need to get a reference from somewhere, so if it isn't
internal it must be external?
I'm far from a device tree expert however, so perhaps this is the
preferred method.
> +
> +#endif
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-27 20:30 ` Jonathan Cameron
(?)
@ 2015-01-29 10:11 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-29 10:11 UTC (permalink / raw)
To: Jonathan Cameron
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Fabio Estevam,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Lee Jones, linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
[-- Attachment #1: Type: text/plain, Size: 18717 bytes --]
On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
> On 24/01/15 14:01, Markus Pargmann wrote:
> > This is a conversion queue driver for the mx25 SoC. It uses the central
> > ADC which is used by two seperate independent queues. This driver
> > prepares different conversion configurations for each possible input.
> > For a conversion it creates a conversionqueue of one item with the
> > correct configuration for the chosen channel. It then executes the queue
> > once and disables the conversion queue afterwards.
> >
> > The reference voltages are configurable through devicetree subnodes,
> > depending on the connections of the ADC inputs.
> >
> > Signed-off-by: Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> > Signed-off-by: Denis Carikli <denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
> A couple of queries inline.
> > ---
> >
> > Notes:
> > Changes in v5:
> > - Fixed locking
> > - Removed module owner
> >
> > .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
> > drivers/iio/adc/Kconfig | 7 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
> > include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
> > 5 files changed, 439 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> > create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> >
> > diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > new file mode 100644
> > index 000000000000..d55b6b751349
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > @@ -0,0 +1,51 @@
> > +Freescale i.MX25 ADC GCQ device
> > +
> > +This is a generic conversion queue device that can convert any of the
> > +analog inputs using the ADC unit of the i.MX25.
> > +
> > +Required properties:
> > + - compatible: Should be "fsl,imx25-gcq".
> > + - reg: Should be the register range of the module.
> > + - interrupts: Should be the interrupt number of the module.
> > + Typically this is <1>.
> > + - interrupt-parent: phandle to the tsadc module of the i.MX25.
> > + - #address-cells: Should be <1> (setting for the subnodes)
> > + - #size-cells: Should be <0> (setting for the subnodes)
> > +
> > +Optional properties:
> > + - vref-supply: The regulator supplying the ADC reference voltage.
> > + Required when at least one subnode uses the external reference.
> > +
> > +Sub-nodes:
> > +Optionally you can define subnodes which define the reference voltage
> > +for the analog inputs.
> > +
> > +Required properties for subnodes:
> > + - reg: Should be the number of the analog input.
> > + 0: xp
> > + 1: yp
> > + 2: xn
> > + 3: yn
> > + 4: wiper
> > + 5: inaux0
> > + 6: inaux1
> > + 7: inaux2
> > + - fsl,adc-ref: specifies the reference input as defined in
> > + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
> > +
> > +Example:
> > +
> > + adc: adc@50030800 {
> > + compatible = "fsl,imx25-gcq";
> > + reg = <0x50030800 0x60>;
> > + interrupt-parent = <&tscadc>;
> > + interrupts = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + inaux@5 {
> > + reg = <5>;
> > + fsl,adc-ref = <MX25_ADC_REF_INT>;
> > + };
> > + };
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 0f79e4725763..fccbb4bf44cc 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -143,6 +143,13 @@ config EXYNOS_ADC
> > of SoCs for drivers such as the touchscreen and hwmon to use to share
> > this resource.
> >
> > +config FSL_MX25_ADC
> > + tristate "Freescale MX25 ADC driver"
> > + depends on MFD_MX25_TSADC
> > + help
> > + Generic Conversion Queue driver used for general purpose ADC in the
> > + MX25. This driver supports single measurements using the MX25 ADC.
> > +
> > config LP8788_ADC
> > tristate "LP8788 ADC driver"
> > depends on MFD_LP8788
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index 701fdb7c96aa..acab8d956371 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
> > obj-$(CONFIG_AT91_ADC) += at91_adc.o
> > obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > obj-$(CONFIG_MAX1027) += max1027.o
> > obj-$(CONFIG_MAX1363) += max1363.o
> > diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> > new file mode 100644
> > index 000000000000..c1ac5af41ec5
> > --- /dev/null
> > +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> > @@ -0,0 +1,369 @@
> > +/*
> > + * Copyright 2014 Markus Pargmann, Pengutronix <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + *
> > + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> > + * connected to the imx25 ADC.
> > + */
> > +
> > +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > +#include <linux/clk.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/mfd/imx25-tsadc.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> > +
> > +enum mx25_gcq_cfgs {
> > + MX25_CFG_XP = 0,
> > + MX25_CFG_YP,
> > + MX25_CFG_XN,
> > + MX25_CFG_YN,
> > + MX25_CFG_WIPER,
> > + MX25_CFG_INAUX0,
> > + MX25_CFG_INAUX1,
> > + MX25_CFG_INAUX2,
> > + MX25_NUM_CFGS,
> > +};
> > +
> > +struct mx25_gcq_priv {
> > + struct regmap *regs;
> > + struct completion completed;
> > + unsigned int settling_time;
> > + struct clk *clk;
> > + int irq;
> > + struct regulator *ext_vref;
> > + u32 channel_vref_mv[MX25_NUM_CFGS];
> > +};
> > +
> > +#define MX25_CQG_CHAN(chan, id) {\
> > + .type = IIO_VOLTAGE,\
> > + .indexed = 1,\
> > + .channel = chan,\
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> > + .datasheet_name = id,\
> > +}
> > +
> > +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> > + MX25_CQG_CHAN(0, "xp"),
> > + MX25_CQG_CHAN(1, "yp"),
> > + MX25_CQG_CHAN(2, "xn"),
> > + MX25_CQG_CHAN(3, "yn"),
> > + MX25_CQG_CHAN(4, "wiper"),
> > + MX25_CQG_CHAN(5, "inaux0"),
> > + MX25_CQG_CHAN(6, "inaux1"),
> > + MX25_CQG_CHAN(7, "inaux2"),
> > +};
> > +
> > +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
> > + MX25_ADCQ_MR_EOQ_IRQ);
> > +}
> > +
> > +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> > + MX25_ADCQ_MR_EOQ_IRQ, 0);
> > +}
> > +
> > +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> > +{
> > + struct mx25_gcq_priv *priv = data;
> > + u32 stats;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> > +
> > + if (stats & MX25_ADCQ_SR_EOQ) {
> > + mx25_gcq_disable_eoq(priv);
> > + complete(&priv->completed);
> > + }
> > +
> > + /* Disable conversion queue run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> > +
> > + /* Acknowledge all possible irqs */
> > + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> > + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> > + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan, int *val,
> > + int *val2, long mask)
> > +{
> > + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> > + long timeout;
> > + u32 data;
> > + int ret = 0;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
> > +
> > + /* Setup the configuration we want to use */
> > + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> > + MX25_ADCQ_ITEM(0, chan->channel));
> > +
> > + mx25_gcq_enable_eoq(priv);
> > +
> > + /* Trigger queue for one run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> > + MX25_ADCQ_CR_FQS);
> > +
> > + timeout = wait_for_completion_interruptible_timeout(
> > + &priv->completed, MX25_GCQ_TIMEOUT);
> > + if (timeout < 0) {
> > + dev_err(&indio_dev->dev,
> > + "ADC wait for measurement failed\n");
> > + ret = timeout;
> > + goto info_raw_out;
> > + } else if (timeout == 0) {
> > + dev_err(&indio_dev->dev, "ADC timed out\n");
> > + ret = -ETIMEDOUT;
> > + goto info_raw_out;
> > + }
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> > +
> > + *val = MX25_ADCQ_FIFO_DATA(data);
> > + ret = IIO_VAL_INT;
> > +info_raw_out:
> Having this label and exit path in the middle is ugly.
> Perhaps break out this case statement content as a separate function?
Sounds like a good idea.
> > + mutex_unlock(&indio_dev->mlock);
> > +
> > + return ret;
> > +
> > + case IIO_CHAN_INFO_SCALE:
> > + *val = priv->channel_vref_mv[chan->channel];
> > + *val2 = 12;
> > + return IIO_VAL_FRACTIONAL_LOG2;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static const struct iio_info mx25_gcq_iio_info = {
> > + .read_raw = mx25_gcq_read_raw,
> > +};
> > +
> > +static const struct regmap_config mx25_gcq_regconfig = {
> > + .max_register = 0x5c,
> > + .reg_bits = 32,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > +};
> > +
> > +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> > + struct mx25_gcq_priv *priv)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct device_node *child;
> > + struct device *dev = &pdev->dev;
> > + int ret, i;
> > +
> > + /*
> > + * Setup all configurations registers with a default conversion
> > + * configuration for each input
> > + */
> > + for (i = 0; i < MX25_NUM_CFGS; ++i)
> > + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> > + MX25_ADCQ_CFG_YPLL_OFF |
> > + MX25_ADCQ_CFG_XNUR_OFF |
> > + MX25_ADCQ_CFG_XPUL_OFF |
> > + MX25_ADCQ_CFG_REFP_INT |
> > + (i << 4) |
> Again, given all the definitions i'd expect the shift to
> be a defined constant as well. Perhaps even a macro taking
> i as an arguement.
Added a macro that shifts the value.
> > + MX25_ADCQ_CFG_REFN_NGND2);
> > +
> > + for_each_child_of_node(np, child) {
> > + u32 reg;
> > + u32 refp;
> > + u32 adc_ref;
> > +
> > + ret = of_property_read_u32(child, "reg", ®);
> > + if (ret) {
> > + dev_err(dev, "Failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + if (reg >= MX25_NUM_CFGS) {
> > + dev_err(dev,
> > + "reg value is greater than the number of available configuration registers\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
> > + if (ret) {
> > + dev_err(dev, "Failed to get fsl,adc-ref property\n");
> > + return ret;
> > + }
> > +
> > + if (adc_ref != MX25_ADC_REF_INT &&
> > + adc_ref != MX25_ADC_REF_EXT) {
> > + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
> > + adc_ref);
> > + return -EINVAL;
> > + }
> > +
> > + switch (adc_ref) {
> > + case MX25_ADC_REF_EXT:
> > + if (IS_ERR_OR_NULL(priv->ext_vref)) {
> > + dev_err(dev,
> > + "No regulator found for the external vref\n");
> > + return -EINVAL;
> > + }
> > + priv->channel_vref_mv[reg] =
> > + regulator_get_voltage(priv->ext_vref);
> > + refp = MX25_ADCQ_CFG_REFP_EXT;
> > + break;
> > + case MX25_ADC_REF_INT:
> > + priv->channel_vref_mv[reg] = 2500;
> > + refp = MX25_ADCQ_CFG_REFP_INT;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> > + MX25_ADCQ_CFG_REFP_MASK |
> > + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
> > + (MX25_ADCQ_CFG_REFN_NGND << 2));
> It's a little inconsistent to define constants for the masks, but not
> the shifts. Particularly given these constants are already shifted in
> their definitions... Is that a bug?
Yes that definetly looks like a bug, thanks. Fixed and added a macro for
refp.
> > + }
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> > +
> > + regmap_write(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_PDMSK |
> > + MX25_ADCQ_CR_QSM_FQS);
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_gcq_probe(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev;
> > + struct mx25_gcq_priv *priv;
> > + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> > + struct device *dev = &pdev->dev;
> > + struct resource *res;
> > + void __iomem *mem;
> > + int ret;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + priv = iio_priv(indio_dev);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + mem = devm_ioremap_resource(dev, res);
> > + if (!mem)
> > + return -ENOMEM;
> > +
> > + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> > + if (IS_ERR(priv->regs)) {
> > + dev_err(dev, "Failed to initialize regmap\n");
> > + return PTR_ERR(priv->regs);
> > + }
> > +
> > + init_completion(&priv->completed);
> > +
> > + /* Optional external regulator */
> > + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> > + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> > + ret = regulator_enable(priv->ext_vref);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + ret = mx25_gcq_setup_cfgs(pdev, priv);
> > + if (ret)
> > + return ret;
> > +
> > + priv->clk = tsadc->clk;
> > + ret = clk_prepare_enable(priv->clk);
> > + if (ret) {
> > + dev_err(dev, "Failed to enable clock\n");
> > + return ret;
> > + }
> > +
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
> > + dev_err(dev, "Failed to get IRQ\n");
> > + ret = priv->irq;
> > + goto err_clk_unprepare;
> > + }
> > +
> > + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
> > + if (ret) {
> > + dev_err(dev, "Failed requesting IRQ\n");
> > + goto err_clk_unprepare;
> > + }
> > +
> > + indio_dev->dev.parent = &pdev->dev;
> > + indio_dev->channels = mx25_gcq_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
> > + indio_dev->info = &mx25_gcq_iio_info;
> > +
> > + ret = iio_device_register(indio_dev);
> > + if (ret) {
> > + dev_err(dev, "Failed to register iio device\n");
> > + goto err_irq_free;
> > + }
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + return 0;
> > +
> > +err_irq_free:
> > + free_irq(priv->irq, (void *)priv);
> > +err_clk_unprepare:
> > + clk_disable_unprepare(priv->clk);
> > + return ret;
> > +}
> > +
> > +static int mx25_gcq_remove(struct platform_device *pdev)
> > +{
> > + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
> > + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
> > +
> > + iio_device_unregister(indio_dev);
> > + free_irq(priv->irq, priv);
> > + clk_disable_unprepare(priv->clk);
> > +
> > + return 0;
> > +}
> > +
> > +static struct of_device_id mx25_gcq_ids[] = {
> > + { .compatible = "fsl,imx25-gcq", },
> > + { /* Sentinel */ }
> > +};
> > +
> > +static struct platform_driver mx25_gcq_driver = {
> > + .driver = {
> > + .name = "mx25-gcq",
> > + .of_match_table = mx25_gcq_ids,
> > + },
> > + .probe = mx25_gcq_probe,
> > + .remove = mx25_gcq_remove,
> > +};
> > +module_platform_driver(mx25_gcq_driver);
> > +
> > +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
> > +MODULE_AUTHOR("Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > new file mode 100644
> > index 000000000000..486dce735ac9
> > --- /dev/null
> > +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > @@ -0,0 +1,11 @@
> > +/*
> > + * This header provides constants for configuring the I.MX25 ADC
> > + */
> > +
> > +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +
> > +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
> > +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
> Seems to me that this could be dealt with using a boolean property.
> Afterall, we need to get a reference from somewhere, so if it isn't
> internal it must be external?
The driver is currently very simple, the ADC itself is capable of much
more combinations and complicated conversion queues. Internal and
external references are not the only possible references. There is also
YP and XP which are not supported by the driver yet. I will change this
to the actual register values representing these references. At a second
look on this it may also be better to change the DT-binding from
'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
voltage. The negative reference is hardcoded in the driver for the
moment but the DT-bindings could be extended later if necessary.
Added refp and refn now with all reference values.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-29 10:11 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-29 10:11 UTC (permalink / raw)
To: Jonathan Cameron
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Fabio Estevam,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel, Lee Jones, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
[-- Attachment #1: Type: text/plain, Size: 18613 bytes --]
On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
> On 24/01/15 14:01, Markus Pargmann wrote:
> > This is a conversion queue driver for the mx25 SoC. It uses the central
> > ADC which is used by two seperate independent queues. This driver
> > prepares different conversion configurations for each possible input.
> > For a conversion it creates a conversionqueue of one item with the
> > correct configuration for the chosen channel. It then executes the queue
> > once and disables the conversion queue afterwards.
> >
> > The reference voltages are configurable through devicetree subnodes,
> > depending on the connections of the ADC inputs.
> >
> > Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> > Signed-off-by: Denis Carikli <denis@eukrea.com>
> A couple of queries inline.
> > ---
> >
> > Notes:
> > Changes in v5:
> > - Fixed locking
> > - Removed module owner
> >
> > .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
> > drivers/iio/adc/Kconfig | 7 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
> > include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
> > 5 files changed, 439 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> > create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> >
> > diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > new file mode 100644
> > index 000000000000..d55b6b751349
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > @@ -0,0 +1,51 @@
> > +Freescale i.MX25 ADC GCQ device
> > +
> > +This is a generic conversion queue device that can convert any of the
> > +analog inputs using the ADC unit of the i.MX25.
> > +
> > +Required properties:
> > + - compatible: Should be "fsl,imx25-gcq".
> > + - reg: Should be the register range of the module.
> > + - interrupts: Should be the interrupt number of the module.
> > + Typically this is <1>.
> > + - interrupt-parent: phandle to the tsadc module of the i.MX25.
> > + - #address-cells: Should be <1> (setting for the subnodes)
> > + - #size-cells: Should be <0> (setting for the subnodes)
> > +
> > +Optional properties:
> > + - vref-supply: The regulator supplying the ADC reference voltage.
> > + Required when at least one subnode uses the external reference.
> > +
> > +Sub-nodes:
> > +Optionally you can define subnodes which define the reference voltage
> > +for the analog inputs.
> > +
> > +Required properties for subnodes:
> > + - reg: Should be the number of the analog input.
> > + 0: xp
> > + 1: yp
> > + 2: xn
> > + 3: yn
> > + 4: wiper
> > + 5: inaux0
> > + 6: inaux1
> > + 7: inaux2
> > + - fsl,adc-ref: specifies the reference input as defined in
> > + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
> > +
> > +Example:
> > +
> > + adc: adc@50030800 {
> > + compatible = "fsl,imx25-gcq";
> > + reg = <0x50030800 0x60>;
> > + interrupt-parent = <&tscadc>;
> > + interrupts = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + inaux@5 {
> > + reg = <5>;
> > + fsl,adc-ref = <MX25_ADC_REF_INT>;
> > + };
> > + };
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 0f79e4725763..fccbb4bf44cc 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -143,6 +143,13 @@ config EXYNOS_ADC
> > of SoCs for drivers such as the touchscreen and hwmon to use to share
> > this resource.
> >
> > +config FSL_MX25_ADC
> > + tristate "Freescale MX25 ADC driver"
> > + depends on MFD_MX25_TSADC
> > + help
> > + Generic Conversion Queue driver used for general purpose ADC in the
> > + MX25. This driver supports single measurements using the MX25 ADC.
> > +
> > config LP8788_ADC
> > tristate "LP8788 ADC driver"
> > depends on MFD_LP8788
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index 701fdb7c96aa..acab8d956371 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
> > obj-$(CONFIG_AT91_ADC) += at91_adc.o
> > obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > obj-$(CONFIG_MAX1027) += max1027.o
> > obj-$(CONFIG_MAX1363) += max1363.o
> > diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> > new file mode 100644
> > index 000000000000..c1ac5af41ec5
> > --- /dev/null
> > +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> > @@ -0,0 +1,369 @@
> > +/*
> > + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + *
> > + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> > + * connected to the imx25 ADC.
> > + */
> > +
> > +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > +#include <linux/clk.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/mfd/imx25-tsadc.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> > +
> > +enum mx25_gcq_cfgs {
> > + MX25_CFG_XP = 0,
> > + MX25_CFG_YP,
> > + MX25_CFG_XN,
> > + MX25_CFG_YN,
> > + MX25_CFG_WIPER,
> > + MX25_CFG_INAUX0,
> > + MX25_CFG_INAUX1,
> > + MX25_CFG_INAUX2,
> > + MX25_NUM_CFGS,
> > +};
> > +
> > +struct mx25_gcq_priv {
> > + struct regmap *regs;
> > + struct completion completed;
> > + unsigned int settling_time;
> > + struct clk *clk;
> > + int irq;
> > + struct regulator *ext_vref;
> > + u32 channel_vref_mv[MX25_NUM_CFGS];
> > +};
> > +
> > +#define MX25_CQG_CHAN(chan, id) {\
> > + .type = IIO_VOLTAGE,\
> > + .indexed = 1,\
> > + .channel = chan,\
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> > + .datasheet_name = id,\
> > +}
> > +
> > +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> > + MX25_CQG_CHAN(0, "xp"),
> > + MX25_CQG_CHAN(1, "yp"),
> > + MX25_CQG_CHAN(2, "xn"),
> > + MX25_CQG_CHAN(3, "yn"),
> > + MX25_CQG_CHAN(4, "wiper"),
> > + MX25_CQG_CHAN(5, "inaux0"),
> > + MX25_CQG_CHAN(6, "inaux1"),
> > + MX25_CQG_CHAN(7, "inaux2"),
> > +};
> > +
> > +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
> > + MX25_ADCQ_MR_EOQ_IRQ);
> > +}
> > +
> > +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> > + MX25_ADCQ_MR_EOQ_IRQ, 0);
> > +}
> > +
> > +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> > +{
> > + struct mx25_gcq_priv *priv = data;
> > + u32 stats;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> > +
> > + if (stats & MX25_ADCQ_SR_EOQ) {
> > + mx25_gcq_disable_eoq(priv);
> > + complete(&priv->completed);
> > + }
> > +
> > + /* Disable conversion queue run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> > +
> > + /* Acknowledge all possible irqs */
> > + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> > + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> > + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan, int *val,
> > + int *val2, long mask)
> > +{
> > + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> > + long timeout;
> > + u32 data;
> > + int ret = 0;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
> > +
> > + /* Setup the configuration we want to use */
> > + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> > + MX25_ADCQ_ITEM(0, chan->channel));
> > +
> > + mx25_gcq_enable_eoq(priv);
> > +
> > + /* Trigger queue for one run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> > + MX25_ADCQ_CR_FQS);
> > +
> > + timeout = wait_for_completion_interruptible_timeout(
> > + &priv->completed, MX25_GCQ_TIMEOUT);
> > + if (timeout < 0) {
> > + dev_err(&indio_dev->dev,
> > + "ADC wait for measurement failed\n");
> > + ret = timeout;
> > + goto info_raw_out;
> > + } else if (timeout == 0) {
> > + dev_err(&indio_dev->dev, "ADC timed out\n");
> > + ret = -ETIMEDOUT;
> > + goto info_raw_out;
> > + }
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> > +
> > + *val = MX25_ADCQ_FIFO_DATA(data);
> > + ret = IIO_VAL_INT;
> > +info_raw_out:
> Having this label and exit path in the middle is ugly.
> Perhaps break out this case statement content as a separate function?
Sounds like a good idea.
> > + mutex_unlock(&indio_dev->mlock);
> > +
> > + return ret;
> > +
> > + case IIO_CHAN_INFO_SCALE:
> > + *val = priv->channel_vref_mv[chan->channel];
> > + *val2 = 12;
> > + return IIO_VAL_FRACTIONAL_LOG2;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static const struct iio_info mx25_gcq_iio_info = {
> > + .read_raw = mx25_gcq_read_raw,
> > +};
> > +
> > +static const struct regmap_config mx25_gcq_regconfig = {
> > + .max_register = 0x5c,
> > + .reg_bits = 32,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > +};
> > +
> > +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> > + struct mx25_gcq_priv *priv)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct device_node *child;
> > + struct device *dev = &pdev->dev;
> > + int ret, i;
> > +
> > + /*
> > + * Setup all configurations registers with a default conversion
> > + * configuration for each input
> > + */
> > + for (i = 0; i < MX25_NUM_CFGS; ++i)
> > + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> > + MX25_ADCQ_CFG_YPLL_OFF |
> > + MX25_ADCQ_CFG_XNUR_OFF |
> > + MX25_ADCQ_CFG_XPUL_OFF |
> > + MX25_ADCQ_CFG_REFP_INT |
> > + (i << 4) |
> Again, given all the definitions i'd expect the shift to
> be a defined constant as well. Perhaps even a macro taking
> i as an arguement.
Added a macro that shifts the value.
> > + MX25_ADCQ_CFG_REFN_NGND2);
> > +
> > + for_each_child_of_node(np, child) {
> > + u32 reg;
> > + u32 refp;
> > + u32 adc_ref;
> > +
> > + ret = of_property_read_u32(child, "reg", ®);
> > + if (ret) {
> > + dev_err(dev, "Failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + if (reg >= MX25_NUM_CFGS) {
> > + dev_err(dev,
> > + "reg value is greater than the number of available configuration registers\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
> > + if (ret) {
> > + dev_err(dev, "Failed to get fsl,adc-ref property\n");
> > + return ret;
> > + }
> > +
> > + if (adc_ref != MX25_ADC_REF_INT &&
> > + adc_ref != MX25_ADC_REF_EXT) {
> > + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
> > + adc_ref);
> > + return -EINVAL;
> > + }
> > +
> > + switch (adc_ref) {
> > + case MX25_ADC_REF_EXT:
> > + if (IS_ERR_OR_NULL(priv->ext_vref)) {
> > + dev_err(dev,
> > + "No regulator found for the external vref\n");
> > + return -EINVAL;
> > + }
> > + priv->channel_vref_mv[reg] =
> > + regulator_get_voltage(priv->ext_vref);
> > + refp = MX25_ADCQ_CFG_REFP_EXT;
> > + break;
> > + case MX25_ADC_REF_INT:
> > + priv->channel_vref_mv[reg] = 2500;
> > + refp = MX25_ADCQ_CFG_REFP_INT;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> > + MX25_ADCQ_CFG_REFP_MASK |
> > + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
> > + (MX25_ADCQ_CFG_REFN_NGND << 2));
> It's a little inconsistent to define constants for the masks, but not
> the shifts. Particularly given these constants are already shifted in
> their definitions... Is that a bug?
Yes that definetly looks like a bug, thanks. Fixed and added a macro for
refp.
> > + }
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> > +
> > + regmap_write(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_PDMSK |
> > + MX25_ADCQ_CR_QSM_FQS);
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_gcq_probe(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev;
> > + struct mx25_gcq_priv *priv;
> > + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> > + struct device *dev = &pdev->dev;
> > + struct resource *res;
> > + void __iomem *mem;
> > + int ret;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + priv = iio_priv(indio_dev);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + mem = devm_ioremap_resource(dev, res);
> > + if (!mem)
> > + return -ENOMEM;
> > +
> > + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> > + if (IS_ERR(priv->regs)) {
> > + dev_err(dev, "Failed to initialize regmap\n");
> > + return PTR_ERR(priv->regs);
> > + }
> > +
> > + init_completion(&priv->completed);
> > +
> > + /* Optional external regulator */
> > + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> > + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> > + ret = regulator_enable(priv->ext_vref);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + ret = mx25_gcq_setup_cfgs(pdev, priv);
> > + if (ret)
> > + return ret;
> > +
> > + priv->clk = tsadc->clk;
> > + ret = clk_prepare_enable(priv->clk);
> > + if (ret) {
> > + dev_err(dev, "Failed to enable clock\n");
> > + return ret;
> > + }
> > +
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
> > + dev_err(dev, "Failed to get IRQ\n");
> > + ret = priv->irq;
> > + goto err_clk_unprepare;
> > + }
> > +
> > + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
> > + if (ret) {
> > + dev_err(dev, "Failed requesting IRQ\n");
> > + goto err_clk_unprepare;
> > + }
> > +
> > + indio_dev->dev.parent = &pdev->dev;
> > + indio_dev->channels = mx25_gcq_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
> > + indio_dev->info = &mx25_gcq_iio_info;
> > +
> > + ret = iio_device_register(indio_dev);
> > + if (ret) {
> > + dev_err(dev, "Failed to register iio device\n");
> > + goto err_irq_free;
> > + }
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + return 0;
> > +
> > +err_irq_free:
> > + free_irq(priv->irq, (void *)priv);
> > +err_clk_unprepare:
> > + clk_disable_unprepare(priv->clk);
> > + return ret;
> > +}
> > +
> > +static int mx25_gcq_remove(struct platform_device *pdev)
> > +{
> > + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
> > + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
> > +
> > + iio_device_unregister(indio_dev);
> > + free_irq(priv->irq, priv);
> > + clk_disable_unprepare(priv->clk);
> > +
> > + return 0;
> > +}
> > +
> > +static struct of_device_id mx25_gcq_ids[] = {
> > + { .compatible = "fsl,imx25-gcq", },
> > + { /* Sentinel */ }
> > +};
> > +
> > +static struct platform_driver mx25_gcq_driver = {
> > + .driver = {
> > + .name = "mx25-gcq",
> > + .of_match_table = mx25_gcq_ids,
> > + },
> > + .probe = mx25_gcq_probe,
> > + .remove = mx25_gcq_remove,
> > +};
> > +module_platform_driver(mx25_gcq_driver);
> > +
> > +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
> > +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > new file mode 100644
> > index 000000000000..486dce735ac9
> > --- /dev/null
> > +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > @@ -0,0 +1,11 @@
> > +/*
> > + * This header provides constants for configuring the I.MX25 ADC
> > + */
> > +
> > +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +
> > +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
> > +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
> Seems to me that this could be dealt with using a boolean property.
> Afterall, we need to get a reference from somewhere, so if it isn't
> internal it must be external?
The driver is currently very simple, the ADC itself is capable of much
more combinations and complicated conversion queues. Internal and
external references are not the only possible references. There is also
YP and XP which are not supported by the driver yet. I will change this
to the actual register values representing these references. At a second
look on this it may also be better to change the DT-binding from
'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
voltage. The negative reference is hardcoded in the driver for the
moment but the DT-bindings could be extended later if necessary.
Added refp and refn now with all reference values.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-29 10:11 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-29 10:11 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
> On 24/01/15 14:01, Markus Pargmann wrote:
> > This is a conversion queue driver for the mx25 SoC. It uses the central
> > ADC which is used by two seperate independent queues. This driver
> > prepares different conversion configurations for each possible input.
> > For a conversion it creates a conversionqueue of one item with the
> > correct configuration for the chosen channel. It then executes the queue
> > once and disables the conversion queue afterwards.
> >
> > The reference voltages are configurable through devicetree subnodes,
> > depending on the connections of the ADC inputs.
> >
> > Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> > Signed-off-by: Denis Carikli <denis@eukrea.com>
> A couple of queries inline.
> > ---
> >
> > Notes:
> > Changes in v5:
> > - Fixed locking
> > - Removed module owner
> >
> > .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
> > drivers/iio/adc/Kconfig | 7 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
> > include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
> > 5 files changed, 439 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> > create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> >
> > diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > new file mode 100644
> > index 000000000000..d55b6b751349
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
> > @@ -0,0 +1,51 @@
> > +Freescale i.MX25 ADC GCQ device
> > +
> > +This is a generic conversion queue device that can convert any of the
> > +analog inputs using the ADC unit of the i.MX25.
> > +
> > +Required properties:
> > + - compatible: Should be "fsl,imx25-gcq".
> > + - reg: Should be the register range of the module.
> > + - interrupts: Should be the interrupt number of the module.
> > + Typically this is <1>.
> > + - interrupt-parent: phandle to the tsadc module of the i.MX25.
> > + - #address-cells: Should be <1> (setting for the subnodes)
> > + - #size-cells: Should be <0> (setting for the subnodes)
> > +
> > +Optional properties:
> > + - vref-supply: The regulator supplying the ADC reference voltage.
> > + Required when at least one subnode uses the external reference.
> > +
> > +Sub-nodes:
> > +Optionally you can define subnodes which define the reference voltage
> > +for the analog inputs.
> > +
> > +Required properties for subnodes:
> > + - reg: Should be the number of the analog input.
> > + 0: xp
> > + 1: yp
> > + 2: xn
> > + 3: yn
> > + 4: wiper
> > + 5: inaux0
> > + 6: inaux1
> > + 7: inaux2
> > + - fsl,adc-ref: specifies the reference input as defined in
> > + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
> > +
> > +Example:
> > +
> > + adc: adc at 50030800 {
> > + compatible = "fsl,imx25-gcq";
> > + reg = <0x50030800 0x60>;
> > + interrupt-parent = <&tscadc>;
> > + interrupts = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + inaux at 5 {
> > + reg = <5>;
> > + fsl,adc-ref = <MX25_ADC_REF_INT>;
> > + };
> > + };
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 0f79e4725763..fccbb4bf44cc 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -143,6 +143,13 @@ config EXYNOS_ADC
> > of SoCs for drivers such as the touchscreen and hwmon to use to share
> > this resource.
> >
> > +config FSL_MX25_ADC
> > + tristate "Freescale MX25 ADC driver"
> > + depends on MFD_MX25_TSADC
> > + help
> > + Generic Conversion Queue driver used for general purpose ADC in the
> > + MX25. This driver supports single measurements using the MX25 ADC.
> > +
> > config LP8788_ADC
> > tristate "LP8788 ADC driver"
> > depends on MFD_LP8788
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index 701fdb7c96aa..acab8d956371 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
> > obj-$(CONFIG_AT91_ADC) += at91_adc.o
> > obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > obj-$(CONFIG_MAX1027) += max1027.o
> > obj-$(CONFIG_MAX1363) += max1363.o
> > diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> > new file mode 100644
> > index 000000000000..c1ac5af41ec5
> > --- /dev/null
> > +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> > @@ -0,0 +1,369 @@
> > +/*
> > + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + *
> > + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> > + * connected to the imx25 ADC.
> > + */
> > +
> > +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > +#include <linux/clk.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/mfd/imx25-tsadc.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> > +
> > +enum mx25_gcq_cfgs {
> > + MX25_CFG_XP = 0,
> > + MX25_CFG_YP,
> > + MX25_CFG_XN,
> > + MX25_CFG_YN,
> > + MX25_CFG_WIPER,
> > + MX25_CFG_INAUX0,
> > + MX25_CFG_INAUX1,
> > + MX25_CFG_INAUX2,
> > + MX25_NUM_CFGS,
> > +};
> > +
> > +struct mx25_gcq_priv {
> > + struct regmap *regs;
> > + struct completion completed;
> > + unsigned int settling_time;
> > + struct clk *clk;
> > + int irq;
> > + struct regulator *ext_vref;
> > + u32 channel_vref_mv[MX25_NUM_CFGS];
> > +};
> > +
> > +#define MX25_CQG_CHAN(chan, id) {\
> > + .type = IIO_VOLTAGE,\
> > + .indexed = 1,\
> > + .channel = chan,\
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> > + .datasheet_name = id,\
> > +}
> > +
> > +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> > + MX25_CQG_CHAN(0, "xp"),
> > + MX25_CQG_CHAN(1, "yp"),
> > + MX25_CQG_CHAN(2, "xn"),
> > + MX25_CQG_CHAN(3, "yn"),
> > + MX25_CQG_CHAN(4, "wiper"),
> > + MX25_CQG_CHAN(5, "inaux0"),
> > + MX25_CQG_CHAN(6, "inaux1"),
> > + MX25_CQG_CHAN(7, "inaux2"),
> > +};
> > +
> > +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
> > + MX25_ADCQ_MR_EOQ_IRQ);
> > +}
> > +
> > +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
> > +{
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> > + MX25_ADCQ_MR_EOQ_IRQ, 0);
> > +}
> > +
> > +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> > +{
> > + struct mx25_gcq_priv *priv = data;
> > + u32 stats;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> > +
> > + if (stats & MX25_ADCQ_SR_EOQ) {
> > + mx25_gcq_disable_eoq(priv);
> > + complete(&priv->completed);
> > + }
> > +
> > + /* Disable conversion queue run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> > +
> > + /* Acknowledge all possible irqs */
> > + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> > + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> > + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan, int *val,
> > + int *val2, long mask)
> > +{
> > + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> > + long timeout;
> > + u32 data;
> > + int ret = 0;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
> > +
> > + /* Setup the configuration we want to use */
> > + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> > + MX25_ADCQ_ITEM(0, chan->channel));
> > +
> > + mx25_gcq_enable_eoq(priv);
> > +
> > + /* Trigger queue for one run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> > + MX25_ADCQ_CR_FQS);
> > +
> > + timeout = wait_for_completion_interruptible_timeout(
> > + &priv->completed, MX25_GCQ_TIMEOUT);
> > + if (timeout < 0) {
> > + dev_err(&indio_dev->dev,
> > + "ADC wait for measurement failed\n");
> > + ret = timeout;
> > + goto info_raw_out;
> > + } else if (timeout == 0) {
> > + dev_err(&indio_dev->dev, "ADC timed out\n");
> > + ret = -ETIMEDOUT;
> > + goto info_raw_out;
> > + }
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> > +
> > + *val = MX25_ADCQ_FIFO_DATA(data);
> > + ret = IIO_VAL_INT;
> > +info_raw_out:
> Having this label and exit path in the middle is ugly.
> Perhaps break out this case statement content as a separate function?
Sounds like a good idea.
> > + mutex_unlock(&indio_dev->mlock);
> > +
> > + return ret;
> > +
> > + case IIO_CHAN_INFO_SCALE:
> > + *val = priv->channel_vref_mv[chan->channel];
> > + *val2 = 12;
> > + return IIO_VAL_FRACTIONAL_LOG2;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static const struct iio_info mx25_gcq_iio_info = {
> > + .read_raw = mx25_gcq_read_raw,
> > +};
> > +
> > +static const struct regmap_config mx25_gcq_regconfig = {
> > + .max_register = 0x5c,
> > + .reg_bits = 32,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > +};
> > +
> > +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> > + struct mx25_gcq_priv *priv)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct device_node *child;
> > + struct device *dev = &pdev->dev;
> > + int ret, i;
> > +
> > + /*
> > + * Setup all configurations registers with a default conversion
> > + * configuration for each input
> > + */
> > + for (i = 0; i < MX25_NUM_CFGS; ++i)
> > + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> > + MX25_ADCQ_CFG_YPLL_OFF |
> > + MX25_ADCQ_CFG_XNUR_OFF |
> > + MX25_ADCQ_CFG_XPUL_OFF |
> > + MX25_ADCQ_CFG_REFP_INT |
> > + (i << 4) |
> Again, given all the definitions i'd expect the shift to
> be a defined constant as well. Perhaps even a macro taking
> i as an arguement.
Added a macro that shifts the value.
> > + MX25_ADCQ_CFG_REFN_NGND2);
> > +
> > + for_each_child_of_node(np, child) {
> > + u32 reg;
> > + u32 refp;
> > + u32 adc_ref;
> > +
> > + ret = of_property_read_u32(child, "reg", ®);
> > + if (ret) {
> > + dev_err(dev, "Failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + if (reg >= MX25_NUM_CFGS) {
> > + dev_err(dev,
> > + "reg value is greater than the number of available configuration registers\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
> > + if (ret) {
> > + dev_err(dev, "Failed to get fsl,adc-ref property\n");
> > + return ret;
> > + }
> > +
> > + if (adc_ref != MX25_ADC_REF_INT &&
> > + adc_ref != MX25_ADC_REF_EXT) {
> > + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
> > + adc_ref);
> > + return -EINVAL;
> > + }
> > +
> > + switch (adc_ref) {
> > + case MX25_ADC_REF_EXT:
> > + if (IS_ERR_OR_NULL(priv->ext_vref)) {
> > + dev_err(dev,
> > + "No regulator found for the external vref\n");
> > + return -EINVAL;
> > + }
> > + priv->channel_vref_mv[reg] =
> > + regulator_get_voltage(priv->ext_vref);
> > + refp = MX25_ADCQ_CFG_REFP_EXT;
> > + break;
> > + case MX25_ADC_REF_INT:
> > + priv->channel_vref_mv[reg] = 2500;
> > + refp = MX25_ADCQ_CFG_REFP_INT;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> > + MX25_ADCQ_CFG_REFP_MASK |
> > + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
> > + (MX25_ADCQ_CFG_REFN_NGND << 2));
> It's a little inconsistent to define constants for the masks, but not
> the shifts. Particularly given these constants are already shifted in
> their definitions... Is that a bug?
Yes that definetly looks like a bug, thanks. Fixed and added a macro for
refp.
> > + }
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> > +
> > + regmap_write(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_PDMSK |
> > + MX25_ADCQ_CR_QSM_FQS);
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_gcq_probe(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev;
> > + struct mx25_gcq_priv *priv;
> > + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> > + struct device *dev = &pdev->dev;
> > + struct resource *res;
> > + void __iomem *mem;
> > + int ret;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + priv = iio_priv(indio_dev);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + mem = devm_ioremap_resource(dev, res);
> > + if (!mem)
> > + return -ENOMEM;
> > +
> > + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> > + if (IS_ERR(priv->regs)) {
> > + dev_err(dev, "Failed to initialize regmap\n");
> > + return PTR_ERR(priv->regs);
> > + }
> > +
> > + init_completion(&priv->completed);
> > +
> > + /* Optional external regulator */
> > + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> > + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> > + ret = regulator_enable(priv->ext_vref);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + ret = mx25_gcq_setup_cfgs(pdev, priv);
> > + if (ret)
> > + return ret;
> > +
> > + priv->clk = tsadc->clk;
> > + ret = clk_prepare_enable(priv->clk);
> > + if (ret) {
> > + dev_err(dev, "Failed to enable clock\n");
> > + return ret;
> > + }
> > +
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
> > + dev_err(dev, "Failed to get IRQ\n");
> > + ret = priv->irq;
> > + goto err_clk_unprepare;
> > + }
> > +
> > + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
> > + if (ret) {
> > + dev_err(dev, "Failed requesting IRQ\n");
> > + goto err_clk_unprepare;
> > + }
> > +
> > + indio_dev->dev.parent = &pdev->dev;
> > + indio_dev->channels = mx25_gcq_channels;
> > + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
> > + indio_dev->info = &mx25_gcq_iio_info;
> > +
> > + ret = iio_device_register(indio_dev);
> > + if (ret) {
> > + dev_err(dev, "Failed to register iio device\n");
> > + goto err_irq_free;
> > + }
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + return 0;
> > +
> > +err_irq_free:
> > + free_irq(priv->irq, (void *)priv);
> > +err_clk_unprepare:
> > + clk_disable_unprepare(priv->clk);
> > + return ret;
> > +}
> > +
> > +static int mx25_gcq_remove(struct platform_device *pdev)
> > +{
> > + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
> > + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
> > +
> > + iio_device_unregister(indio_dev);
> > + free_irq(priv->irq, priv);
> > + clk_disable_unprepare(priv->clk);
> > +
> > + return 0;
> > +}
> > +
> > +static struct of_device_id mx25_gcq_ids[] = {
> > + { .compatible = "fsl,imx25-gcq", },
> > + { /* Sentinel */ }
> > +};
> > +
> > +static struct platform_driver mx25_gcq_driver = {
> > + .driver = {
> > + .name = "mx25-gcq",
> > + .of_match_table = mx25_gcq_ids,
> > + },
> > + .probe = mx25_gcq_probe,
> > + .remove = mx25_gcq_remove,
> > +};
> > +module_platform_driver(mx25_gcq_driver);
> > +
> > +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
> > +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > new file mode 100644
> > index 000000000000..486dce735ac9
> > --- /dev/null
> > +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> > @@ -0,0 +1,11 @@
> > +/*
> > + * This header provides constants for configuring the I.MX25 ADC
> > + */
> > +
> > +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
> > +
> > +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
> > +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
> Seems to me that this could be dealt with using a boolean property.
> Afterall, we need to get a reference from somewhere, so if it isn't
> internal it must be external?
The driver is currently very simple, the ADC itself is capable of much
more combinations and complicated conversion queues. Internal and
external references are not the only possible references. There is also
YP and XP which are not supported by the driver yet. I will change this
to the actual register values representing these references. At a second
look on this it may also be better to change the DT-binding from
'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
voltage. The negative reference is hardcoded in the driver for the
moment but the DT-bindings could be extended later if necessary.
Added refp and refn now with all reference values.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150129/39e3e325/attachment-0001.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-24 14:01 ` Markus Pargmann
(?)
@ 2015-01-29 14:51 ` Fabio Estevam
-1 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-01-29 14:51 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Lee Jones, linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
Hi Markus,
On Sat, Jan 24, 2015 at 12:01 PM, Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org> wrote:
> + priv->irq = platform_get_irq(pdev, 0);
> + if (priv->irq <= 0) {
This should be: if (priv->irq < 0) {
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-29 14:51 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-01-29 14:51 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel, Lee Jones, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
Hi Markus,
On Sat, Jan 24, 2015 at 12:01 PM, Markus Pargmann <mpa@pengutronix.de> wrote:
> + priv->irq = platform_get_irq(pdev, 0);
> + if (priv->irq <= 0) {
This should be: if (priv->irq < 0) {
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-29 14:51 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-01-29 14:51 UTC (permalink / raw)
To: linux-arm-kernel
Hi Markus,
On Sat, Jan 24, 2015 at 12:01 PM, Markus Pargmann <mpa@pengutronix.de> wrote:
> + priv->irq = platform_get_irq(pdev, 0);
> + if (priv->irq <= 0) {
This should be: if (priv->irq < 0) {
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-29 14:51 ` Fabio Estevam
@ 2015-01-30 7:27 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-30 7:27 UTC (permalink / raw)
To: Fabio Estevam
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel, Lee Jones, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
[-- Attachment #1: Type: text/plain, Size: 683 bytes --]
Hi Fabio,
On Thu, Jan 29, 2015 at 12:51:36PM -0200, Fabio Estevam wrote:
> Hi Markus,
>
> On Sat, Jan 24, 2015 at 12:01 PM, Markus Pargmann <mpa@pengutronix.de> wrote:
>
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
>
> This should be: if (priv->irq < 0) {
Thanks, fixed in both drivers.
Best regards,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-01-30 7:27 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-01-30 7:27 UTC (permalink / raw)
To: linux-arm-kernel
Hi Fabio,
On Thu, Jan 29, 2015 at 12:51:36PM -0200, Fabio Estevam wrote:
> Hi Markus,
>
> On Sat, Jan 24, 2015 at 12:01 PM, Markus Pargmann <mpa@pengutronix.de> wrote:
>
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
>
> This should be: if (priv->irq < 0) {
Thanks, fixed in both drivers.
Best regards,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150130/ad2b7ac8/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
2015-01-29 10:11 ` Markus Pargmann
(?)
@ 2015-02-08 11:56 ` Jonathan Cameron
-1 siblings, 0 replies; 50+ messages in thread
From: Jonathan Cameron @ 2015-02-08 11:56 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Fabio Estevam,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Lee Jones, linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
On 29/01/15 10:11, Markus Pargmann wrote:
> On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
>> On 24/01/15 14:01, Markus Pargmann wrote:
>>> This is a conversion queue driver for the mx25 SoC. It uses the central
>>> ADC which is used by two seperate independent queues. This driver
>>> prepares different conversion configurations for each possible input.
>>> For a conversion it creates a conversionqueue of one item with the
>>> correct configuration for the chosen channel. It then executes the queue
>>> once and disables the conversion queue afterwards.
>>>
>>> The reference voltages are configurable through devicetree subnodes,
>>> depending on the connections of the ADC inputs.
>>>
>>> Signed-off-by: Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
>>> Signed-off-by: Denis Carikli <denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
>> A couple of queries inline.
>>> ---
>>>
>>> Notes:
>>> Changes in v5:
>>> - Fixed locking
>>> - Removed module owner
>>>
>>> .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
>>> drivers/iio/adc/Kconfig | 7 +
>>> drivers/iio/adc/Makefile | 1 +
>>> drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
>>> include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
>>> 5 files changed, 439 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
>>> create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>>
>>> diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> new file mode 100644
>>> index 000000000000..d55b6b751349
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> @@ -0,0 +1,51 @@
>>> +Freescale i.MX25 ADC GCQ device
>>> +
>>> +This is a generic conversion queue device that can convert any of the
>>> +analog inputs using the ADC unit of the i.MX25.
>>> +
>>> +Required properties:
>>> + - compatible: Should be "fsl,imx25-gcq".
>>> + - reg: Should be the register range of the module.
>>> + - interrupts: Should be the interrupt number of the module.
>>> + Typically this is <1>.
>>> + - interrupt-parent: phandle to the tsadc module of the i.MX25.
>>> + - #address-cells: Should be <1> (setting for the subnodes)
>>> + - #size-cells: Should be <0> (setting for the subnodes)
>>> +
>>> +Optional properties:
>>> + - vref-supply: The regulator supplying the ADC reference voltage.
>>> + Required when at least one subnode uses the external reference.
>>> +
>>> +Sub-nodes:
>>> +Optionally you can define subnodes which define the reference voltage
>>> +for the analog inputs.
>>> +
>>> +Required properties for subnodes:
>>> + - reg: Should be the number of the analog input.
>>> + 0: xp
>>> + 1: yp
>>> + 2: xn
>>> + 3: yn
>>> + 4: wiper
>>> + 5: inaux0
>>> + 6: inaux1
>>> + 7: inaux2
>>> + - fsl,adc-ref: specifies the reference input as defined in
>>> + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
>>> +
>>> +Example:
>>> +
>>> + adc: adc@50030800 {
>>> + compatible = "fsl,imx25-gcq";
>>> + reg = <0x50030800 0x60>;
>>> + interrupt-parent = <&tscadc>;
>>> + interrupts = <1>;
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + inaux@5 {
>>> + reg = <5>;
>>> + fsl,adc-ref = <MX25_ADC_REF_INT>;
>>> + };
>>> + };
>>> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
>>> index 0f79e4725763..fccbb4bf44cc 100644
>>> --- a/drivers/iio/adc/Kconfig
>>> +++ b/drivers/iio/adc/Kconfig
>>> @@ -143,6 +143,13 @@ config EXYNOS_ADC
>>> of SoCs for drivers such as the touchscreen and hwmon to use to share
>>> this resource.
>>>
>>> +config FSL_MX25_ADC
>>> + tristate "Freescale MX25 ADC driver"
>>> + depends on MFD_MX25_TSADC
>>> + help
>>> + Generic Conversion Queue driver used for general purpose ADC in the
>>> + MX25. This driver supports single measurements using the MX25 ADC.
>>> +
>>> config LP8788_ADC
>>> tristate "LP8788 ADC driver"
>>> depends on MFD_LP8788
>>> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
>>> index 701fdb7c96aa..acab8d956371 100644
>>> --- a/drivers/iio/adc/Makefile
>>> +++ b/drivers/iio/adc/Makefile
>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
>>> obj-$(CONFIG_AT91_ADC) += at91_adc.o
>>> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>>> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
>>> +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
>>> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
>>> obj-$(CONFIG_MAX1027) += max1027.o
>>> obj-$(CONFIG_MAX1363) += max1363.o
>>> diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
>>> new file mode 100644
>>> index 000000000000..c1ac5af41ec5
>>> --- /dev/null
>>> +++ b/drivers/iio/adc/fsl-imx25-gcq.c
>>> @@ -0,0 +1,369 @@
>>> +/*
>>> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
>>> + *
>>> + * The code contained herein is licensed under the GNU General Public
>>> + * License. You may obtain a copy of the GNU General Public License
>>> + * Version 2 or later at the following locations:
>>> + *
>>> + * http://www.opensource.org/licenses/gpl-license.html
>>> + * http://www.gnu.org/copyleft/gpl.html
>>> + *
>>> + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
>>> + * connected to the imx25 ADC.
>>> + */
>>> +
>>> +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/iio/iio.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/mfd/imx25-tsadc.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/regulator/consumer.h>
>>> +
>>> +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
>>> +
>>> +enum mx25_gcq_cfgs {
>>> + MX25_CFG_XP = 0,
>>> + MX25_CFG_YP,
>>> + MX25_CFG_XN,
>>> + MX25_CFG_YN,
>>> + MX25_CFG_WIPER,
>>> + MX25_CFG_INAUX0,
>>> + MX25_CFG_INAUX1,
>>> + MX25_CFG_INAUX2,
>>> + MX25_NUM_CFGS,
>>> +};
>>> +
>>> +struct mx25_gcq_priv {
>>> + struct regmap *regs;
>>> + struct completion completed;
>>> + unsigned int settling_time;
>>> + struct clk *clk;
>>> + int irq;
>>> + struct regulator *ext_vref;
>>> + u32 channel_vref_mv[MX25_NUM_CFGS];
>>> +};
>>> +
>>> +#define MX25_CQG_CHAN(chan, id) {\
>>> + .type = IIO_VOLTAGE,\
>>> + .indexed = 1,\
>>> + .channel = chan,\
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
>>> + .datasheet_name = id,\
>>> +}
>>> +
>>> +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
>>> + MX25_CQG_CHAN(0, "xp"),
>>> + MX25_CQG_CHAN(1, "yp"),
>>> + MX25_CQG_CHAN(2, "xn"),
>>> + MX25_CQG_CHAN(3, "yn"),
>>> + MX25_CQG_CHAN(4, "wiper"),
>>> + MX25_CQG_CHAN(5, "inaux0"),
>>> + MX25_CQG_CHAN(6, "inaux1"),
>>> + MX25_CQG_CHAN(7, "inaux2"),
>>> +};
>>> +
>>> +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
>>> + MX25_ADCQ_MR_EOQ_IRQ);
>>> +}
>>> +
>>> +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
>>> + MX25_ADCQ_MR_EOQ_IRQ, 0);
>>> +}
>>> +
>>> +static irqreturn_t mx25_gcq_irq(int irq, void *data)
>>> +{
>>> + struct mx25_gcq_priv *priv = data;
>>> + u32 stats;
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
>>> +
>>> + if (stats & MX25_ADCQ_SR_EOQ) {
>>> + mx25_gcq_disable_eoq(priv);
>>> + complete(&priv->completed);
>>> + }
>>> +
>>> + /* Disable conversion queue run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
>>> +
>>> + /* Acknowledge all possible irqs */
>>> + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
>>> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
>>> + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
>>> +
>>> + return IRQ_HANDLED;
>>> +}
>>> +
>>> +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan, int *val,
>>> + int *val2, long mask)
>>> +{
>>> + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
>>> + long timeout;
>>> + u32 data;
>>> + int ret = 0;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_RAW:
>>> + mutex_lock(&indio_dev->mlock);
>>> +
>>> + /* Setup the configuration we want to use */
>>> + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
>>> + MX25_ADCQ_ITEM(0, chan->channel));
>>> +
>>> + mx25_gcq_enable_eoq(priv);
>>> +
>>> + /* Trigger queue for one run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
>>> + MX25_ADCQ_CR_FQS);
>>> +
>>> + timeout = wait_for_completion_interruptible_timeout(
>>> + &priv->completed, MX25_GCQ_TIMEOUT);
>>> + if (timeout < 0) {
>>> + dev_err(&indio_dev->dev,
>>> + "ADC wait for measurement failed\n");
>>> + ret = timeout;
>>> + goto info_raw_out;
>>> + } else if (timeout == 0) {
>>> + dev_err(&indio_dev->dev, "ADC timed out\n");
>>> + ret = -ETIMEDOUT;
>>> + goto info_raw_out;
>>> + }
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
>>> +
>>> + *val = MX25_ADCQ_FIFO_DATA(data);
>>> + ret = IIO_VAL_INT;
>>> +info_raw_out:
>> Having this label and exit path in the middle is ugly.
>> Perhaps break out this case statement content as a separate function?
>
> Sounds like a good idea.
>
>>> + mutex_unlock(&indio_dev->mlock);
>>> +
>>> + return ret;
>>> +
>>> + case IIO_CHAN_INFO_SCALE:
>>> + *val = priv->channel_vref_mv[chan->channel];
>>> + *val2 = 12;
>>> + return IIO_VAL_FRACTIONAL_LOG2;
>>> +
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +}
>>> +
>>> +static const struct iio_info mx25_gcq_iio_info = {
>>> + .read_raw = mx25_gcq_read_raw,
>>> +};
>>> +
>>> +static const struct regmap_config mx25_gcq_regconfig = {
>>> + .max_register = 0x5c,
>>> + .reg_bits = 32,
>>> + .val_bits = 32,
>>> + .reg_stride = 4,
>>> +};
>>> +
>>> +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
>>> + struct mx25_gcq_priv *priv)
>>> +{
>>> + struct device_node *np = pdev->dev.of_node;
>>> + struct device_node *child;
>>> + struct device *dev = &pdev->dev;
>>> + int ret, i;
>>> +
>>> + /*
>>> + * Setup all configurations registers with a default conversion
>>> + * configuration for each input
>>> + */
>>> + for (i = 0; i < MX25_NUM_CFGS; ++i)
>>> + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
>>> + MX25_ADCQ_CFG_YPLL_OFF |
>>> + MX25_ADCQ_CFG_XNUR_OFF |
>>> + MX25_ADCQ_CFG_XPUL_OFF |
>>> + MX25_ADCQ_CFG_REFP_INT |
>>> + (i << 4) |
>> Again, given all the definitions i'd expect the shift to
>> be a defined constant as well. Perhaps even a macro taking
>> i as an arguement.
>
> Added a macro that shifts the value.
>
>>> + MX25_ADCQ_CFG_REFN_NGND2);
>>> +
>>> + for_each_child_of_node(np, child) {
>>> + u32 reg;
>>> + u32 refp;
>>> + u32 adc_ref;
>>> +
>>> + ret = of_property_read_u32(child, "reg", ®);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get reg property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (reg >= MX25_NUM_CFGS) {
>>> + dev_err(dev,
>>> + "reg value is greater than the number of available configuration registers\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get fsl,adc-ref property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (adc_ref != MX25_ADC_REF_INT &&
>>> + adc_ref != MX25_ADC_REF_EXT) {
>>> + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
>>> + adc_ref);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + switch (adc_ref) {
>>> + case MX25_ADC_REF_EXT:
>>> + if (IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + dev_err(dev,
>>> + "No regulator found for the external vref\n");
>>> + return -EINVAL;
>>> + }
>>> + priv->channel_vref_mv[reg] =
>>> + regulator_get_voltage(priv->ext_vref);
>>> + refp = MX25_ADCQ_CFG_REFP_EXT;
>>> + break;
>>> + case MX25_ADC_REF_INT:
>>> + priv->channel_vref_mv[reg] = 2500;
>>> + refp = MX25_ADCQ_CFG_REFP_INT;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
>>> + MX25_ADCQ_CFG_REFP_MASK |
>>> + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
>>> + (MX25_ADCQ_CFG_REFN_NGND << 2));
>> It's a little inconsistent to define constants for the masks, but not
>> the shifts. Particularly given these constants are already shifted in
>> their definitions... Is that a bug?
>
> Yes that definetly looks like a bug, thanks. Fixed and added a macro for
> refp.
>
>>> + }
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
>>> +
>>> + regmap_write(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_PDMSK |
>>> + MX25_ADCQ_CR_QSM_FQS);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int mx25_gcq_probe(struct platform_device *pdev)
>>> +{
>>> + struct iio_dev *indio_dev;
>>> + struct mx25_gcq_priv *priv;
>>> + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
>>> + struct device *dev = &pdev->dev;
>>> + struct resource *res;
>>> + void __iomem *mem;
>>> + int ret;
>>> +
>>> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
>>> + if (!indio_dev)
>>> + return -ENOMEM;
>>> +
>>> + priv = iio_priv(indio_dev);
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + mem = devm_ioremap_resource(dev, res);
>>> + if (!mem)
>>> + return -ENOMEM;
>>> +
>>> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
>>> + if (IS_ERR(priv->regs)) {
>>> + dev_err(dev, "Failed to initialize regmap\n");
>>> + return PTR_ERR(priv->regs);
>>> + }
>>> +
>>> + init_completion(&priv->completed);
>>> +
>>> + /* Optional external regulator */
>>> + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
>>> + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + ret = regulator_enable(priv->ext_vref);
>>> + if (ret)
>>> + return ret;
>>> + }
>>> +
>>> + ret = mx25_gcq_setup_cfgs(pdev, priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + priv->clk = tsadc->clk;
>>> + ret = clk_prepare_enable(priv->clk);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to enable clock\n");
>>> + return ret;
>>> + }
>>> +
>>> + priv->irq = platform_get_irq(pdev, 0);
>>> + if (priv->irq <= 0) {
>>> + dev_err(dev, "Failed to get IRQ\n");
>>> + ret = priv->irq;
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
>>> + if (ret) {
>>> + dev_err(dev, "Failed requesting IRQ\n");
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + indio_dev->dev.parent = &pdev->dev;
>>> + indio_dev->channels = mx25_gcq_channels;
>>> + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
>>> + indio_dev->info = &mx25_gcq_iio_info;
>>> +
>>> + ret = iio_device_register(indio_dev);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to register iio device\n");
>>> + goto err_irq_free;
>>> + }
>>> +
>>> + platform_set_drvdata(pdev, priv);
>>> +
>>> + return 0;
>>> +
>>> +err_irq_free:
>>> + free_irq(priv->irq, (void *)priv);
>>> +err_clk_unprepare:
>>> + clk_disable_unprepare(priv->clk);
>>> + return ret;
>>> +}
>>> +
>>> +static int mx25_gcq_remove(struct platform_device *pdev)
>>> +{
>>> + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
>>> + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
>>> +
>>> + iio_device_unregister(indio_dev);
>>> + free_irq(priv->irq, priv);
>>> + clk_disable_unprepare(priv->clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct of_device_id mx25_gcq_ids[] = {
>>> + { .compatible = "fsl,imx25-gcq", },
>>> + { /* Sentinel */ }
>>> +};
>>> +
>>> +static struct platform_driver mx25_gcq_driver = {
>>> + .driver = {
>>> + .name = "mx25-gcq",
>>> + .of_match_table = mx25_gcq_ids,
>>> + },
>>> + .probe = mx25_gcq_probe,
>>> + .remove = mx25_gcq_remove,
>>> +};
>>> +module_platform_driver(mx25_gcq_driver);
>>> +
>>> +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
>>> +MODULE_AUTHOR("Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> new file mode 100644
>>> index 000000000000..486dce735ac9
>>> --- /dev/null
>>> +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> @@ -0,0 +1,11 @@
>>> +/*
>>> + * This header provides constants for configuring the I.MX25 ADC
>>> + */
>>> +
>>> +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +
>>> +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
>>> +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
>> Seems to me that this could be dealt with using a boolean property.
>> Afterall, we need to get a reference from somewhere, so if it isn't
>> internal it must be external?
>
> The driver is currently very simple, the ADC itself is capable of much
> more combinations and complicated conversion queues. Internal and
> external references are not the only possible references.
Fair enough then. Thanks for clarifying this!
> There is also
> YP and XP which are not supported by the driver yet. I will change this
> to the actual register values representing these references. At a second
> look on this it may also be better to change the DT-binding from
> 'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
> voltage. The negative reference is hardcoded in the driver for the
> moment but the DT-bindings could be extended later if necessary.
>
> Added refp and refn now with all reference values.
>
> Thanks,
>
> Markus
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-02-08 11:56 ` Jonathan Cameron
0 siblings, 0 replies; 50+ messages in thread
From: Jonathan Cameron @ 2015-02-08 11:56 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Fabio Estevam,
Peter Meerwald, Hartmut Knaack, Denis Carikli, Eric Bénard,
Sascha Hauer, linux-arm-kernel, Lee Jones, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On 29/01/15 10:11, Markus Pargmann wrote:
> On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
>> On 24/01/15 14:01, Markus Pargmann wrote:
>>> This is a conversion queue driver for the mx25 SoC. It uses the central
>>> ADC which is used by two seperate independent queues. This driver
>>> prepares different conversion configurations for each possible input.
>>> For a conversion it creates a conversionqueue of one item with the
>>> correct configuration for the chosen channel. It then executes the queue
>>> once and disables the conversion queue afterwards.
>>>
>>> The reference voltages are configurable through devicetree subnodes,
>>> depending on the connections of the ADC inputs.
>>>
>>> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
>>> Signed-off-by: Denis Carikli <denis@eukrea.com>
>> A couple of queries inline.
>>> ---
>>>
>>> Notes:
>>> Changes in v5:
>>> - Fixed locking
>>> - Removed module owner
>>>
>>> .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
>>> drivers/iio/adc/Kconfig | 7 +
>>> drivers/iio/adc/Makefile | 1 +
>>> drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
>>> include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
>>> 5 files changed, 439 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
>>> create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>>
>>> diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> new file mode 100644
>>> index 000000000000..d55b6b751349
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> @@ -0,0 +1,51 @@
>>> +Freescale i.MX25 ADC GCQ device
>>> +
>>> +This is a generic conversion queue device that can convert any of the
>>> +analog inputs using the ADC unit of the i.MX25.
>>> +
>>> +Required properties:
>>> + - compatible: Should be "fsl,imx25-gcq".
>>> + - reg: Should be the register range of the module.
>>> + - interrupts: Should be the interrupt number of the module.
>>> + Typically this is <1>.
>>> + - interrupt-parent: phandle to the tsadc module of the i.MX25.
>>> + - #address-cells: Should be <1> (setting for the subnodes)
>>> + - #size-cells: Should be <0> (setting for the subnodes)
>>> +
>>> +Optional properties:
>>> + - vref-supply: The regulator supplying the ADC reference voltage.
>>> + Required when at least one subnode uses the external reference.
>>> +
>>> +Sub-nodes:
>>> +Optionally you can define subnodes which define the reference voltage
>>> +for the analog inputs.
>>> +
>>> +Required properties for subnodes:
>>> + - reg: Should be the number of the analog input.
>>> + 0: xp
>>> + 1: yp
>>> + 2: xn
>>> + 3: yn
>>> + 4: wiper
>>> + 5: inaux0
>>> + 6: inaux1
>>> + 7: inaux2
>>> + - fsl,adc-ref: specifies the reference input as defined in
>>> + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
>>> +
>>> +Example:
>>> +
>>> + adc: adc@50030800 {
>>> + compatible = "fsl,imx25-gcq";
>>> + reg = <0x50030800 0x60>;
>>> + interrupt-parent = <&tscadc>;
>>> + interrupts = <1>;
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + inaux@5 {
>>> + reg = <5>;
>>> + fsl,adc-ref = <MX25_ADC_REF_INT>;
>>> + };
>>> + };
>>> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
>>> index 0f79e4725763..fccbb4bf44cc 100644
>>> --- a/drivers/iio/adc/Kconfig
>>> +++ b/drivers/iio/adc/Kconfig
>>> @@ -143,6 +143,13 @@ config EXYNOS_ADC
>>> of SoCs for drivers such as the touchscreen and hwmon to use to share
>>> this resource.
>>>
>>> +config FSL_MX25_ADC
>>> + tristate "Freescale MX25 ADC driver"
>>> + depends on MFD_MX25_TSADC
>>> + help
>>> + Generic Conversion Queue driver used for general purpose ADC in the
>>> + MX25. This driver supports single measurements using the MX25 ADC.
>>> +
>>> config LP8788_ADC
>>> tristate "LP8788 ADC driver"
>>> depends on MFD_LP8788
>>> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
>>> index 701fdb7c96aa..acab8d956371 100644
>>> --- a/drivers/iio/adc/Makefile
>>> +++ b/drivers/iio/adc/Makefile
>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
>>> obj-$(CONFIG_AT91_ADC) += at91_adc.o
>>> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>>> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
>>> +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
>>> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
>>> obj-$(CONFIG_MAX1027) += max1027.o
>>> obj-$(CONFIG_MAX1363) += max1363.o
>>> diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
>>> new file mode 100644
>>> index 000000000000..c1ac5af41ec5
>>> --- /dev/null
>>> +++ b/drivers/iio/adc/fsl-imx25-gcq.c
>>> @@ -0,0 +1,369 @@
>>> +/*
>>> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
>>> + *
>>> + * The code contained herein is licensed under the GNU General Public
>>> + * License. You may obtain a copy of the GNU General Public License
>>> + * Version 2 or later at the following locations:
>>> + *
>>> + * http://www.opensource.org/licenses/gpl-license.html
>>> + * http://www.gnu.org/copyleft/gpl.html
>>> + *
>>> + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
>>> + * connected to the imx25 ADC.
>>> + */
>>> +
>>> +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/iio/iio.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/mfd/imx25-tsadc.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/regulator/consumer.h>
>>> +
>>> +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
>>> +
>>> +enum mx25_gcq_cfgs {
>>> + MX25_CFG_XP = 0,
>>> + MX25_CFG_YP,
>>> + MX25_CFG_XN,
>>> + MX25_CFG_YN,
>>> + MX25_CFG_WIPER,
>>> + MX25_CFG_INAUX0,
>>> + MX25_CFG_INAUX1,
>>> + MX25_CFG_INAUX2,
>>> + MX25_NUM_CFGS,
>>> +};
>>> +
>>> +struct mx25_gcq_priv {
>>> + struct regmap *regs;
>>> + struct completion completed;
>>> + unsigned int settling_time;
>>> + struct clk *clk;
>>> + int irq;
>>> + struct regulator *ext_vref;
>>> + u32 channel_vref_mv[MX25_NUM_CFGS];
>>> +};
>>> +
>>> +#define MX25_CQG_CHAN(chan, id) {\
>>> + .type = IIO_VOLTAGE,\
>>> + .indexed = 1,\
>>> + .channel = chan,\
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
>>> + .datasheet_name = id,\
>>> +}
>>> +
>>> +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
>>> + MX25_CQG_CHAN(0, "xp"),
>>> + MX25_CQG_CHAN(1, "yp"),
>>> + MX25_CQG_CHAN(2, "xn"),
>>> + MX25_CQG_CHAN(3, "yn"),
>>> + MX25_CQG_CHAN(4, "wiper"),
>>> + MX25_CQG_CHAN(5, "inaux0"),
>>> + MX25_CQG_CHAN(6, "inaux1"),
>>> + MX25_CQG_CHAN(7, "inaux2"),
>>> +};
>>> +
>>> +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
>>> + MX25_ADCQ_MR_EOQ_IRQ);
>>> +}
>>> +
>>> +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
>>> + MX25_ADCQ_MR_EOQ_IRQ, 0);
>>> +}
>>> +
>>> +static irqreturn_t mx25_gcq_irq(int irq, void *data)
>>> +{
>>> + struct mx25_gcq_priv *priv = data;
>>> + u32 stats;
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
>>> +
>>> + if (stats & MX25_ADCQ_SR_EOQ) {
>>> + mx25_gcq_disable_eoq(priv);
>>> + complete(&priv->completed);
>>> + }
>>> +
>>> + /* Disable conversion queue run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
>>> +
>>> + /* Acknowledge all possible irqs */
>>> + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
>>> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
>>> + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
>>> +
>>> + return IRQ_HANDLED;
>>> +}
>>> +
>>> +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan, int *val,
>>> + int *val2, long mask)
>>> +{
>>> + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
>>> + long timeout;
>>> + u32 data;
>>> + int ret = 0;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_RAW:
>>> + mutex_lock(&indio_dev->mlock);
>>> +
>>> + /* Setup the configuration we want to use */
>>> + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
>>> + MX25_ADCQ_ITEM(0, chan->channel));
>>> +
>>> + mx25_gcq_enable_eoq(priv);
>>> +
>>> + /* Trigger queue for one run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
>>> + MX25_ADCQ_CR_FQS);
>>> +
>>> + timeout = wait_for_completion_interruptible_timeout(
>>> + &priv->completed, MX25_GCQ_TIMEOUT);
>>> + if (timeout < 0) {
>>> + dev_err(&indio_dev->dev,
>>> + "ADC wait for measurement failed\n");
>>> + ret = timeout;
>>> + goto info_raw_out;
>>> + } else if (timeout == 0) {
>>> + dev_err(&indio_dev->dev, "ADC timed out\n");
>>> + ret = -ETIMEDOUT;
>>> + goto info_raw_out;
>>> + }
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
>>> +
>>> + *val = MX25_ADCQ_FIFO_DATA(data);
>>> + ret = IIO_VAL_INT;
>>> +info_raw_out:
>> Having this label and exit path in the middle is ugly.
>> Perhaps break out this case statement content as a separate function?
>
> Sounds like a good idea.
>
>>> + mutex_unlock(&indio_dev->mlock);
>>> +
>>> + return ret;
>>> +
>>> + case IIO_CHAN_INFO_SCALE:
>>> + *val = priv->channel_vref_mv[chan->channel];
>>> + *val2 = 12;
>>> + return IIO_VAL_FRACTIONAL_LOG2;
>>> +
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +}
>>> +
>>> +static const struct iio_info mx25_gcq_iio_info = {
>>> + .read_raw = mx25_gcq_read_raw,
>>> +};
>>> +
>>> +static const struct regmap_config mx25_gcq_regconfig = {
>>> + .max_register = 0x5c,
>>> + .reg_bits = 32,
>>> + .val_bits = 32,
>>> + .reg_stride = 4,
>>> +};
>>> +
>>> +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
>>> + struct mx25_gcq_priv *priv)
>>> +{
>>> + struct device_node *np = pdev->dev.of_node;
>>> + struct device_node *child;
>>> + struct device *dev = &pdev->dev;
>>> + int ret, i;
>>> +
>>> + /*
>>> + * Setup all configurations registers with a default conversion
>>> + * configuration for each input
>>> + */
>>> + for (i = 0; i < MX25_NUM_CFGS; ++i)
>>> + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
>>> + MX25_ADCQ_CFG_YPLL_OFF |
>>> + MX25_ADCQ_CFG_XNUR_OFF |
>>> + MX25_ADCQ_CFG_XPUL_OFF |
>>> + MX25_ADCQ_CFG_REFP_INT |
>>> + (i << 4) |
>> Again, given all the definitions i'd expect the shift to
>> be a defined constant as well. Perhaps even a macro taking
>> i as an arguement.
>
> Added a macro that shifts the value.
>
>>> + MX25_ADCQ_CFG_REFN_NGND2);
>>> +
>>> + for_each_child_of_node(np, child) {
>>> + u32 reg;
>>> + u32 refp;
>>> + u32 adc_ref;
>>> +
>>> + ret = of_property_read_u32(child, "reg", ®);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get reg property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (reg >= MX25_NUM_CFGS) {
>>> + dev_err(dev,
>>> + "reg value is greater than the number of available configuration registers\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get fsl,adc-ref property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (adc_ref != MX25_ADC_REF_INT &&
>>> + adc_ref != MX25_ADC_REF_EXT) {
>>> + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
>>> + adc_ref);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + switch (adc_ref) {
>>> + case MX25_ADC_REF_EXT:
>>> + if (IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + dev_err(dev,
>>> + "No regulator found for the external vref\n");
>>> + return -EINVAL;
>>> + }
>>> + priv->channel_vref_mv[reg] =
>>> + regulator_get_voltage(priv->ext_vref);
>>> + refp = MX25_ADCQ_CFG_REFP_EXT;
>>> + break;
>>> + case MX25_ADC_REF_INT:
>>> + priv->channel_vref_mv[reg] = 2500;
>>> + refp = MX25_ADCQ_CFG_REFP_INT;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
>>> + MX25_ADCQ_CFG_REFP_MASK |
>>> + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
>>> + (MX25_ADCQ_CFG_REFN_NGND << 2));
>> It's a little inconsistent to define constants for the masks, but not
>> the shifts. Particularly given these constants are already shifted in
>> their definitions... Is that a bug?
>
> Yes that definetly looks like a bug, thanks. Fixed and added a macro for
> refp.
>
>>> + }
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
>>> +
>>> + regmap_write(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_PDMSK |
>>> + MX25_ADCQ_CR_QSM_FQS);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int mx25_gcq_probe(struct platform_device *pdev)
>>> +{
>>> + struct iio_dev *indio_dev;
>>> + struct mx25_gcq_priv *priv;
>>> + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
>>> + struct device *dev = &pdev->dev;
>>> + struct resource *res;
>>> + void __iomem *mem;
>>> + int ret;
>>> +
>>> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
>>> + if (!indio_dev)
>>> + return -ENOMEM;
>>> +
>>> + priv = iio_priv(indio_dev);
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + mem = devm_ioremap_resource(dev, res);
>>> + if (!mem)
>>> + return -ENOMEM;
>>> +
>>> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
>>> + if (IS_ERR(priv->regs)) {
>>> + dev_err(dev, "Failed to initialize regmap\n");
>>> + return PTR_ERR(priv->regs);
>>> + }
>>> +
>>> + init_completion(&priv->completed);
>>> +
>>> + /* Optional external regulator */
>>> + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
>>> + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + ret = regulator_enable(priv->ext_vref);
>>> + if (ret)
>>> + return ret;
>>> + }
>>> +
>>> + ret = mx25_gcq_setup_cfgs(pdev, priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + priv->clk = tsadc->clk;
>>> + ret = clk_prepare_enable(priv->clk);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to enable clock\n");
>>> + return ret;
>>> + }
>>> +
>>> + priv->irq = platform_get_irq(pdev, 0);
>>> + if (priv->irq <= 0) {
>>> + dev_err(dev, "Failed to get IRQ\n");
>>> + ret = priv->irq;
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
>>> + if (ret) {
>>> + dev_err(dev, "Failed requesting IRQ\n");
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + indio_dev->dev.parent = &pdev->dev;
>>> + indio_dev->channels = mx25_gcq_channels;
>>> + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
>>> + indio_dev->info = &mx25_gcq_iio_info;
>>> +
>>> + ret = iio_device_register(indio_dev);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to register iio device\n");
>>> + goto err_irq_free;
>>> + }
>>> +
>>> + platform_set_drvdata(pdev, priv);
>>> +
>>> + return 0;
>>> +
>>> +err_irq_free:
>>> + free_irq(priv->irq, (void *)priv);
>>> +err_clk_unprepare:
>>> + clk_disable_unprepare(priv->clk);
>>> + return ret;
>>> +}
>>> +
>>> +static int mx25_gcq_remove(struct platform_device *pdev)
>>> +{
>>> + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
>>> + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
>>> +
>>> + iio_device_unregister(indio_dev);
>>> + free_irq(priv->irq, priv);
>>> + clk_disable_unprepare(priv->clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct of_device_id mx25_gcq_ids[] = {
>>> + { .compatible = "fsl,imx25-gcq", },
>>> + { /* Sentinel */ }
>>> +};
>>> +
>>> +static struct platform_driver mx25_gcq_driver = {
>>> + .driver = {
>>> + .name = "mx25-gcq",
>>> + .of_match_table = mx25_gcq_ids,
>>> + },
>>> + .probe = mx25_gcq_probe,
>>> + .remove = mx25_gcq_remove,
>>> +};
>>> +module_platform_driver(mx25_gcq_driver);
>>> +
>>> +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
>>> +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> new file mode 100644
>>> index 000000000000..486dce735ac9
>>> --- /dev/null
>>> +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> @@ -0,0 +1,11 @@
>>> +/*
>>> + * This header provides constants for configuring the I.MX25 ADC
>>> + */
>>> +
>>> +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +
>>> +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
>>> +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
>> Seems to me that this could be dealt with using a boolean property.
>> Afterall, we need to get a reference from somewhere, so if it isn't
>> internal it must be external?
>
> The driver is currently very simple, the ADC itself is capable of much
> more combinations and complicated conversion queues. Internal and
> external references are not the only possible references.
Fair enough then. Thanks for clarifying this!
> There is also
> YP and XP which are not supported by the driver yet. I will change this
> to the actual register values representing these references. At a second
> look on this it may also be better to change the DT-binding from
> 'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
> voltage. The negative reference is hardcoded in the driver for the
> moment but the DT-bindings could be extended later if necessary.
>
> Added refp and refn now with all reference values.
>
> Thanks,
>
> Markus
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver
@ 2015-02-08 11:56 ` Jonathan Cameron
0 siblings, 0 replies; 50+ messages in thread
From: Jonathan Cameron @ 2015-02-08 11:56 UTC (permalink / raw)
To: linux-arm-kernel
On 29/01/15 10:11, Markus Pargmann wrote:
> On Tue, Jan 27, 2015 at 08:30:56PM +0000, Jonathan Cameron wrote:
>> On 24/01/15 14:01, Markus Pargmann wrote:
>>> This is a conversion queue driver for the mx25 SoC. It uses the central
>>> ADC which is used by two seperate independent queues. This driver
>>> prepares different conversion configurations for each possible input.
>>> For a conversion it creates a conversionqueue of one item with the
>>> correct configuration for the chosen channel. It then executes the queue
>>> once and disables the conversion queue afterwards.
>>>
>>> The reference voltages are configurable through devicetree subnodes,
>>> depending on the connections of the ADC inputs.
>>>
>>> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
>>> Signed-off-by: Denis Carikli <denis@eukrea.com>
>> A couple of queries inline.
>>> ---
>>>
>>> Notes:
>>> Changes in v5:
>>> - Fixed locking
>>> - Removed module owner
>>>
>>> .../devicetree/bindings/iio/adc/fsl,imx25-gcq.txt | 51 +++
>>> drivers/iio/adc/Kconfig | 7 +
>>> drivers/iio/adc/Makefile | 1 +
>>> drivers/iio/adc/fsl-imx25-gcq.c | 369 +++++++++++++++++++++
>>> include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 11 +
>>> 5 files changed, 439 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
>>> create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>>
>>> diff --git a/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> new file mode 100644
>>> index 000000000000..d55b6b751349
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/iio/adc/fsl,imx25-gcq.txt
>>> @@ -0,0 +1,51 @@
>>> +Freescale i.MX25 ADC GCQ device
>>> +
>>> +This is a generic conversion queue device that can convert any of the
>>> +analog inputs using the ADC unit of the i.MX25.
>>> +
>>> +Required properties:
>>> + - compatible: Should be "fsl,imx25-gcq".
>>> + - reg: Should be the register range of the module.
>>> + - interrupts: Should be the interrupt number of the module.
>>> + Typically this is <1>.
>>> + - interrupt-parent: phandle to the tsadc module of the i.MX25.
>>> + - #address-cells: Should be <1> (setting for the subnodes)
>>> + - #size-cells: Should be <0> (setting for the subnodes)
>>> +
>>> +Optional properties:
>>> + - vref-supply: The regulator supplying the ADC reference voltage.
>>> + Required when at least one subnode uses the external reference.
>>> +
>>> +Sub-nodes:
>>> +Optionally you can define subnodes which define the reference voltage
>>> +for the analog inputs.
>>> +
>>> +Required properties for subnodes:
>>> + - reg: Should be the number of the analog input.
>>> + 0: xp
>>> + 1: yp
>>> + 2: xn
>>> + 3: yn
>>> + 4: wiper
>>> + 5: inaux0
>>> + 6: inaux1
>>> + 7: inaux2
>>> + - fsl,adc-ref: specifies the reference input as defined in
>>> + <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> + MX25_ADC_REF_INT and MX25_ADC_REF_EXT flags are supported.
>>> +
>>> +Example:
>>> +
>>> + adc: adc at 50030800 {
>>> + compatible = "fsl,imx25-gcq";
>>> + reg = <0x50030800 0x60>;
>>> + interrupt-parent = <&tscadc>;
>>> + interrupts = <1>;
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + inaux at 5 {
>>> + reg = <5>;
>>> + fsl,adc-ref = <MX25_ADC_REF_INT>;
>>> + };
>>> + };
>>> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
>>> index 0f79e4725763..fccbb4bf44cc 100644
>>> --- a/drivers/iio/adc/Kconfig
>>> +++ b/drivers/iio/adc/Kconfig
>>> @@ -143,6 +143,13 @@ config EXYNOS_ADC
>>> of SoCs for drivers such as the touchscreen and hwmon to use to share
>>> this resource.
>>>
>>> +config FSL_MX25_ADC
>>> + tristate "Freescale MX25 ADC driver"
>>> + depends on MFD_MX25_TSADC
>>> + help
>>> + Generic Conversion Queue driver used for general purpose ADC in the
>>> + MX25. This driver supports single measurements using the MX25 ADC.
>>> +
>>> config LP8788_ADC
>>> tristate "LP8788 ADC driver"
>>> depends on MFD_LP8788
>>> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
>>> index 701fdb7c96aa..acab8d956371 100644
>>> --- a/drivers/iio/adc/Makefile
>>> +++ b/drivers/iio/adc/Makefile
>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
>>> obj-$(CONFIG_AT91_ADC) += at91_adc.o
>>> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>>> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
>>> +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
>>> obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
>>> obj-$(CONFIG_MAX1027) += max1027.o
>>> obj-$(CONFIG_MAX1363) += max1363.o
>>> diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
>>> new file mode 100644
>>> index 000000000000..c1ac5af41ec5
>>> --- /dev/null
>>> +++ b/drivers/iio/adc/fsl-imx25-gcq.c
>>> @@ -0,0 +1,369 @@
>>> +/*
>>> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
>>> + *
>>> + * The code contained herein is licensed under the GNU General Public
>>> + * License. You may obtain a copy of the GNU General Public License
>>> + * Version 2 or later at the following locations:
>>> + *
>>> + * http://www.opensource.org/licenses/gpl-license.html
>>> + * http://www.gnu.org/copyleft/gpl.html
>>> + *
>>> + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
>>> + * connected to the imx25 ADC.
>>> + */
>>> +
>>> +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/iio/iio.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/mfd/imx25-tsadc.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/regulator/consumer.h>
>>> +
>>> +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
>>> +
>>> +enum mx25_gcq_cfgs {
>>> + MX25_CFG_XP = 0,
>>> + MX25_CFG_YP,
>>> + MX25_CFG_XN,
>>> + MX25_CFG_YN,
>>> + MX25_CFG_WIPER,
>>> + MX25_CFG_INAUX0,
>>> + MX25_CFG_INAUX1,
>>> + MX25_CFG_INAUX2,
>>> + MX25_NUM_CFGS,
>>> +};
>>> +
>>> +struct mx25_gcq_priv {
>>> + struct regmap *regs;
>>> + struct completion completed;
>>> + unsigned int settling_time;
>>> + struct clk *clk;
>>> + int irq;
>>> + struct regulator *ext_vref;
>>> + u32 channel_vref_mv[MX25_NUM_CFGS];
>>> +};
>>> +
>>> +#define MX25_CQG_CHAN(chan, id) {\
>>> + .type = IIO_VOLTAGE,\
>>> + .indexed = 1,\
>>> + .channel = chan,\
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
>>> + .datasheet_name = id,\
>>> +}
>>> +
>>> +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
>>> + MX25_CQG_CHAN(0, "xp"),
>>> + MX25_CQG_CHAN(1, "yp"),
>>> + MX25_CQG_CHAN(2, "xn"),
>>> + MX25_CQG_CHAN(3, "yn"),
>>> + MX25_CQG_CHAN(4, "wiper"),
>>> + MX25_CQG_CHAN(5, "inaux0"),
>>> + MX25_CQG_CHAN(6, "inaux1"),
>>> + MX25_CQG_CHAN(7, "inaux2"),
>>> +};
>>> +
>>> +static void mx25_gcq_disable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ,
>>> + MX25_ADCQ_MR_EOQ_IRQ);
>>> +}
>>> +
>>> +static void mx25_gcq_enable_eoq(struct mx25_gcq_priv *priv)
>>> +{
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
>>> + MX25_ADCQ_MR_EOQ_IRQ, 0);
>>> +}
>>> +
>>> +static irqreturn_t mx25_gcq_irq(int irq, void *data)
>>> +{
>>> + struct mx25_gcq_priv *priv = data;
>>> + u32 stats;
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
>>> +
>>> + if (stats & MX25_ADCQ_SR_EOQ) {
>>> + mx25_gcq_disable_eoq(priv);
>>> + complete(&priv->completed);
>>> + }
>>> +
>>> + /* Disable conversion queue run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
>>> +
>>> + /* Acknowledge all possible irqs */
>>> + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
>>> + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
>>> + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
>>> +
>>> + return IRQ_HANDLED;
>>> +}
>>> +
>>> +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan, int *val,
>>> + int *val2, long mask)
>>> +{
>>> + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
>>> + long timeout;
>>> + u32 data;
>>> + int ret = 0;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_RAW:
>>> + mutex_lock(&indio_dev->mlock);
>>> +
>>> + /* Setup the configuration we want to use */
>>> + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
>>> + MX25_ADCQ_ITEM(0, chan->channel));
>>> +
>>> + mx25_gcq_enable_eoq(priv);
>>> +
>>> + /* Trigger queue for one run */
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
>>> + MX25_ADCQ_CR_FQS);
>>> +
>>> + timeout = wait_for_completion_interruptible_timeout(
>>> + &priv->completed, MX25_GCQ_TIMEOUT);
>>> + if (timeout < 0) {
>>> + dev_err(&indio_dev->dev,
>>> + "ADC wait for measurement failed\n");
>>> + ret = timeout;
>>> + goto info_raw_out;
>>> + } else if (timeout == 0) {
>>> + dev_err(&indio_dev->dev, "ADC timed out\n");
>>> + ret = -ETIMEDOUT;
>>> + goto info_raw_out;
>>> + }
>>> +
>>> + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
>>> +
>>> + *val = MX25_ADCQ_FIFO_DATA(data);
>>> + ret = IIO_VAL_INT;
>>> +info_raw_out:
>> Having this label and exit path in the middle is ugly.
>> Perhaps break out this case statement content as a separate function?
>
> Sounds like a good idea.
>
>>> + mutex_unlock(&indio_dev->mlock);
>>> +
>>> + return ret;
>>> +
>>> + case IIO_CHAN_INFO_SCALE:
>>> + *val = priv->channel_vref_mv[chan->channel];
>>> + *val2 = 12;
>>> + return IIO_VAL_FRACTIONAL_LOG2;
>>> +
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +}
>>> +
>>> +static const struct iio_info mx25_gcq_iio_info = {
>>> + .read_raw = mx25_gcq_read_raw,
>>> +};
>>> +
>>> +static const struct regmap_config mx25_gcq_regconfig = {
>>> + .max_register = 0x5c,
>>> + .reg_bits = 32,
>>> + .val_bits = 32,
>>> + .reg_stride = 4,
>>> +};
>>> +
>>> +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
>>> + struct mx25_gcq_priv *priv)
>>> +{
>>> + struct device_node *np = pdev->dev.of_node;
>>> + struct device_node *child;
>>> + struct device *dev = &pdev->dev;
>>> + int ret, i;
>>> +
>>> + /*
>>> + * Setup all configurations registers with a default conversion
>>> + * configuration for each input
>>> + */
>>> + for (i = 0; i < MX25_NUM_CFGS; ++i)
>>> + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
>>> + MX25_ADCQ_CFG_YPLL_OFF |
>>> + MX25_ADCQ_CFG_XNUR_OFF |
>>> + MX25_ADCQ_CFG_XPUL_OFF |
>>> + MX25_ADCQ_CFG_REFP_INT |
>>> + (i << 4) |
>> Again, given all the definitions i'd expect the shift to
>> be a defined constant as well. Perhaps even a macro taking
>> i as an arguement.
>
> Added a macro that shifts the value.
>
>>> + MX25_ADCQ_CFG_REFN_NGND2);
>>> +
>>> + for_each_child_of_node(np, child) {
>>> + u32 reg;
>>> + u32 refp;
>>> + u32 adc_ref;
>>> +
>>> + ret = of_property_read_u32(child, "reg", ®);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get reg property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (reg >= MX25_NUM_CFGS) {
>>> + dev_err(dev,
>>> + "reg value is greater than the number of available configuration registers\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + ret = of_property_read_u32(child, "fsl,adc-ref", &adc_ref);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to get fsl,adc-ref property\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (adc_ref != MX25_ADC_REF_INT &&
>>> + adc_ref != MX25_ADC_REF_EXT) {
>>> + dev_err(dev, "Invalid fsl,adc-refp property value %d\n",
>>> + adc_ref);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + switch (adc_ref) {
>>> + case MX25_ADC_REF_EXT:
>>> + if (IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + dev_err(dev,
>>> + "No regulator found for the external vref\n");
>>> + return -EINVAL;
>>> + }
>>> + priv->channel_vref_mv[reg] =
>>> + regulator_get_voltage(priv->ext_vref);
>>> + refp = MX25_ADCQ_CFG_REFP_EXT;
>>> + break;
>>> + case MX25_ADC_REF_INT:
>>> + priv->channel_vref_mv[reg] = 2500;
>>> + refp = MX25_ADCQ_CFG_REFP_INT;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
>>> + MX25_ADCQ_CFG_REFP_MASK |
>>> + MX25_ADCQ_CFG_REFN_MASK, (refp << 7) |
>>> + (MX25_ADCQ_CFG_REFN_NGND << 2));
>> It's a little inconsistent to define constants for the masks, but not
>> the shifts. Particularly given these constants are already shifted in
>> their definitions... Is that a bug?
>
> Yes that definetly looks like a bug, thanks. Fixed and added a macro for
> refp.
>
>>> + }
>>> + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
>>> + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
>>> +
>>> + regmap_write(priv->regs, MX25_ADCQ_CR,
>>> + MX25_ADCQ_CR_PDMSK |
>>> + MX25_ADCQ_CR_QSM_FQS);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int mx25_gcq_probe(struct platform_device *pdev)
>>> +{
>>> + struct iio_dev *indio_dev;
>>> + struct mx25_gcq_priv *priv;
>>> + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
>>> + struct device *dev = &pdev->dev;
>>> + struct resource *res;
>>> + void __iomem *mem;
>>> + int ret;
>>> +
>>> + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
>>> + if (!indio_dev)
>>> + return -ENOMEM;
>>> +
>>> + priv = iio_priv(indio_dev);
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + mem = devm_ioremap_resource(dev, res);
>>> + if (!mem)
>>> + return -ENOMEM;
>>> +
>>> + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
>>> + if (IS_ERR(priv->regs)) {
>>> + dev_err(dev, "Failed to initialize regmap\n");
>>> + return PTR_ERR(priv->regs);
>>> + }
>>> +
>>> + init_completion(&priv->completed);
>>> +
>>> + /* Optional external regulator */
>>> + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
>>> + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
>>> + ret = regulator_enable(priv->ext_vref);
>>> + if (ret)
>>> + return ret;
>>> + }
>>> +
>>> + ret = mx25_gcq_setup_cfgs(pdev, priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + priv->clk = tsadc->clk;
>>> + ret = clk_prepare_enable(priv->clk);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to enable clock\n");
>>> + return ret;
>>> + }
>>> +
>>> + priv->irq = platform_get_irq(pdev, 0);
>>> + if (priv->irq <= 0) {
>>> + dev_err(dev, "Failed to get IRQ\n");
>>> + ret = priv->irq;
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
>>> + if (ret) {
>>> + dev_err(dev, "Failed requesting IRQ\n");
>>> + goto err_clk_unprepare;
>>> + }
>>> +
>>> + indio_dev->dev.parent = &pdev->dev;
>>> + indio_dev->channels = mx25_gcq_channels;
>>> + indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
>>> + indio_dev->info = &mx25_gcq_iio_info;
>>> +
>>> + ret = iio_device_register(indio_dev);
>>> + if (ret) {
>>> + dev_err(dev, "Failed to register iio device\n");
>>> + goto err_irq_free;
>>> + }
>>> +
>>> + platform_set_drvdata(pdev, priv);
>>> +
>>> + return 0;
>>> +
>>> +err_irq_free:
>>> + free_irq(priv->irq, (void *)priv);
>>> +err_clk_unprepare:
>>> + clk_disable_unprepare(priv->clk);
>>> + return ret;
>>> +}
>>> +
>>> +static int mx25_gcq_remove(struct platform_device *pdev)
>>> +{
>>> + struct mx25_gcq_priv *priv = platform_get_drvdata(pdev);
>>> + struct iio_dev *indio_dev = iio_priv_to_dev(pdev);
>>> +
>>> + iio_device_unregister(indio_dev);
>>> + free_irq(priv->irq, priv);
>>> + clk_disable_unprepare(priv->clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct of_device_id mx25_gcq_ids[] = {
>>> + { .compatible = "fsl,imx25-gcq", },
>>> + { /* Sentinel */ }
>>> +};
>>> +
>>> +static struct platform_driver mx25_gcq_driver = {
>>> + .driver = {
>>> + .name = "mx25-gcq",
>>> + .of_match_table = mx25_gcq_ids,
>>> + },
>>> + .probe = mx25_gcq_probe,
>>> + .remove = mx25_gcq_remove,
>>> +};
>>> +module_platform_driver(mx25_gcq_driver);
>>> +
>>> +MODULE_DESCRIPTION("ADC driver for Freescale mx25");
>>> +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/include/dt-bindings/iio/adc/fsl-imx25-gcq.h b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> new file mode 100644
>>> index 000000000000..486dce735ac9
>>> --- /dev/null
>>> +++ b/include/dt-bindings/iio/adc/fsl-imx25-gcq.h
>>> @@ -0,0 +1,11 @@
>>> +/*
>>> + * This header provides constants for configuring the I.MX25 ADC
>>> + */
>>> +
>>> +#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
>>> +
>>> +#define MX25_ADC_REF_INT 0 /* Internal voltage reference */
>>> +#define MX25_ADC_REF_EXT 1 /* External voltage reference */
>> Seems to me that this could be dealt with using a boolean property.
>> Afterall, we need to get a reference from somewhere, so if it isn't
>> internal it must be external?
>
> The driver is currently very simple, the ADC itself is capable of much
> more combinations and complicated conversion queues. Internal and
> external references are not the only possible references.
Fair enough then. Thanks for clarifying this!
> There is also
> YP and XP which are not supported by the driver yet. I will change this
> to the actual register values representing these references. At a second
> look on this it may also be better to change the DT-binding from
> 'fsl,adc-ref' to 'fsl,adc-refp' as it is actually the positive reference
> voltage. The negative reference is hardcoded in the driver for the
> moment but the DT-bindings could be extended later if necessary.
>
> Added refp and refn now with all reference values.
>
> Thanks,
>
> Markus
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-01-24 14:01 ` Markus Pargmann
(?)
@ 2015-02-16 13:38 ` Lee Jones
-1 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-16 13:38 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
On Sat, 24 Jan 2015, Markus Pargmann wrote:
> This is the core driver for imx25 touchscreen/adc driver. The module
> has one shared ADC and two different conversion queues which use the
> ADC. The two queues are identical. Both can be used for general purpose
> ADC but one is meant to be used for touchscreens.
>
> This driver is the core which manages the central components and
> registers of the TSC/ADC unit. It manages the IRQs and forwards them to
> the correct components.
>
> Signed-off-by: Markus Pargmann <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> Signed-off-by: Denis Carikli <denis-fO0SIAKYzcbQT0dZR+AlfA@public.gmane.org>
> Acked-by: Jonathan Cameron <jic23-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> ---
>
> Notes:
> Changes in v5:
> - Remove ifdef CONFIG_OF as this driver is only for DT usage
> - Remove module owner
> - Add Kconfig dependencies ARCH_MX25 and OF
>
> @Jonathan Cameron:
> I left your acked-by on the patch as these were small changes. If it should be
> removed, please say so. Thanks
>
> drivers/mfd/Kconfig | 10 +++
> drivers/mfd/Makefile | 2 +
> drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/imx25-tsadc.h | 140 +++++++++++++++++++++++++++++++++
> 4 files changed, 319 insertions(+)
> create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
> create mode 100644 include/linux/mfd/imx25-tsadc.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 2e6b7311fabc..44fc15598a6a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -232,6 +232,16 @@ config MFD_MC13XXX_I2C
> help
> Select this if your MC13xxx is connected via an I2C bus.
>
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
> + depends on OF
> + help
> + Enable support for the integrated Touchscreen and ADC unit of the
> + i.MX25 processors. They consist of a conversion queue for general
> + purpose ADC and a queue for Touchscreens.
> +
> config MFD_HI6421_PMIC
> tristate "HiSilicon Hi6421 PMU/Codec IC"
> depends on OF
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 53467e211381..3feeb29f5938 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -78,6 +78,8 @@ obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o
> obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
> obj-$(CONFIG_TWL6040_CORE) += twl6040.o
>
> +obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
> +
> obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
> obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
> obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
> diff --git a/drivers/mfd/fsl-imx25-tsadc.c b/drivers/mfd/fsl-imx25-tsadc.c
> new file mode 100644
> index 000000000000..8e4013d57500
> --- /dev/null
> +++ b/drivers/mfd/fsl-imx25-tsadc.c
> @@ -0,0 +1,167 @@
> +/*
> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqchip/chained_irq.h>
> +#include <linux/irqdesc.h>
> +#include <linux/irqdomain.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/imx25-tsadc.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
[...]
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + int irq;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
What if 0 is returned?
> + dev_err(dev, "Failed to get irq\n");
> + return irq;
> + }
> +
> + tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
> + tsadc);
> + if (!tsadc->domain) {
> + dev_err(dev, "Failed to add irq domain\n");
> + return -ENOMEM;
> + }
> +
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
> +
> + return 0;
> +}
> diff --git a/include/linux/mfd/imx25-tsadc.h b/include/linux/mfd/imx25-tsadc.h
> new file mode 100644
> index 000000000000..8086f18847fe
> --- /dev/null
> +++ b/include/linux/mfd/imx25-tsadc.h
> @@ -0,0 +1,140 @@
> +#ifndef _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
> +#define _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
INPUT?
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-16 13:38 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-16 13:38 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Sat, 24 Jan 2015, Markus Pargmann wrote:
> This is the core driver for imx25 touchscreen/adc driver. The module
> has one shared ADC and two different conversion queues which use the
> ADC. The two queues are identical. Both can be used for general purpose
> ADC but one is meant to be used for touchscreens.
>
> This driver is the core which manages the central components and
> registers of the TSC/ADC unit. It manages the IRQs and forwards them to
> the correct components.
>
> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> Signed-off-by: Denis Carikli <denis@eukrea.com>
> Acked-by: Jonathan Cameron <jic23@kernel.org>
> ---
>
> Notes:
> Changes in v5:
> - Remove ifdef CONFIG_OF as this driver is only for DT usage
> - Remove module owner
> - Add Kconfig dependencies ARCH_MX25 and OF
>
> @Jonathan Cameron:
> I left your acked-by on the patch as these were small changes. If it should be
> removed, please say so. Thanks
>
> drivers/mfd/Kconfig | 10 +++
> drivers/mfd/Makefile | 2 +
> drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/imx25-tsadc.h | 140 +++++++++++++++++++++++++++++++++
> 4 files changed, 319 insertions(+)
> create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
> create mode 100644 include/linux/mfd/imx25-tsadc.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 2e6b7311fabc..44fc15598a6a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -232,6 +232,16 @@ config MFD_MC13XXX_I2C
> help
> Select this if your MC13xxx is connected via an I2C bus.
>
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
> + depends on OF
> + help
> + Enable support for the integrated Touchscreen and ADC unit of the
> + i.MX25 processors. They consist of a conversion queue for general
> + purpose ADC and a queue for Touchscreens.
> +
> config MFD_HI6421_PMIC
> tristate "HiSilicon Hi6421 PMU/Codec IC"
> depends on OF
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 53467e211381..3feeb29f5938 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -78,6 +78,8 @@ obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o
> obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
> obj-$(CONFIG_TWL6040_CORE) += twl6040.o
>
> +obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
> +
> obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
> obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
> obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
> diff --git a/drivers/mfd/fsl-imx25-tsadc.c b/drivers/mfd/fsl-imx25-tsadc.c
> new file mode 100644
> index 000000000000..8e4013d57500
> --- /dev/null
> +++ b/drivers/mfd/fsl-imx25-tsadc.c
> @@ -0,0 +1,167 @@
> +/*
> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqchip/chained_irq.h>
> +#include <linux/irqdesc.h>
> +#include <linux/irqdomain.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/imx25-tsadc.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
[...]
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + int irq;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
What if 0 is returned?
> + dev_err(dev, "Failed to get irq\n");
> + return irq;
> + }
> +
> + tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
> + tsadc);
> + if (!tsadc->domain) {
> + dev_err(dev, "Failed to add irq domain\n");
> + return -ENOMEM;
> + }
> +
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
> +
> + return 0;
> +}
> diff --git a/include/linux/mfd/imx25-tsadc.h b/include/linux/mfd/imx25-tsadc.h
> new file mode 100644
> index 000000000000..8086f18847fe
> --- /dev/null
> +++ b/include/linux/mfd/imx25-tsadc.h
> @@ -0,0 +1,140 @@
> +#ifndef _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
> +#define _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
INPUT?
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-16 13:38 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-16 13:38 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 24 Jan 2015, Markus Pargmann wrote:
> This is the core driver for imx25 touchscreen/adc driver. The module
> has one shared ADC and two different conversion queues which use the
> ADC. The two queues are identical. Both can be used for general purpose
> ADC but one is meant to be used for touchscreens.
>
> This driver is the core which manages the central components and
> registers of the TSC/ADC unit. It manages the IRQs and forwards them to
> the correct components.
>
> Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
> Signed-off-by: Denis Carikli <denis@eukrea.com>
> Acked-by: Jonathan Cameron <jic23@kernel.org>
> ---
>
> Notes:
> Changes in v5:
> - Remove ifdef CONFIG_OF as this driver is only for DT usage
> - Remove module owner
> - Add Kconfig dependencies ARCH_MX25 and OF
>
> @Jonathan Cameron:
> I left your acked-by on the patch as these were small changes. If it should be
> removed, please say so. Thanks
>
> drivers/mfd/Kconfig | 10 +++
> drivers/mfd/Makefile | 2 +
> drivers/mfd/fsl-imx25-tsadc.c | 167 ++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/imx25-tsadc.h | 140 +++++++++++++++++++++++++++++++++
> 4 files changed, 319 insertions(+)
> create mode 100644 drivers/mfd/fsl-imx25-tsadc.c
> create mode 100644 include/linux/mfd/imx25-tsadc.h
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 2e6b7311fabc..44fc15598a6a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -232,6 +232,16 @@ config MFD_MC13XXX_I2C
> help
> Select this if your MC13xxx is connected via an I2C bus.
>
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
> + depends on OF
> + help
> + Enable support for the integrated Touchscreen and ADC unit of the
> + i.MX25 processors. They consist of a conversion queue for general
> + purpose ADC and a queue for Touchscreens.
> +
> config MFD_HI6421_PMIC
> tristate "HiSilicon Hi6421 PMU/Codec IC"
> depends on OF
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 53467e211381..3feeb29f5938 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -78,6 +78,8 @@ obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o
> obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
> obj-$(CONFIG_TWL6040_CORE) += twl6040.o
>
> +obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
> +
> obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
> obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
> obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
> diff --git a/drivers/mfd/fsl-imx25-tsadc.c b/drivers/mfd/fsl-imx25-tsadc.c
> new file mode 100644
> index 000000000000..8e4013d57500
> --- /dev/null
> +++ b/drivers/mfd/fsl-imx25-tsadc.c
> @@ -0,0 +1,167 @@
> +/*
> + * Copyright 2014 Markus Pargmann, Pengutronix <mpa@pengutronix.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqchip/chained_irq.h>
> +#include <linux/irqdesc.h>
> +#include <linux/irqdomain.h>
> +#include <linux/irq.h>
> +#include <linux/mfd/imx25-tsadc.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
[...]
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + int irq;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
What if 0 is returned?
> + dev_err(dev, "Failed to get irq\n");
> + return irq;
> + }
> +
> + tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
> + tsadc);
> + if (!tsadc->domain) {
> + dev_err(dev, "Failed to add irq domain\n");
> + return -ENOMEM;
> + }
> +
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
> +
> + return 0;
> +}
> diff --git a/include/linux/mfd/imx25-tsadc.h b/include/linux/mfd/imx25-tsadc.h
> new file mode 100644
> index 000000000000..8086f18847fe
> --- /dev/null
> +++ b/include/linux/mfd/imx25-tsadc.h
> @@ -0,0 +1,140 @@
> +#ifndef _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
> +#define _LINUX_INCLUDE_INPUT_IMX25_TSADC_H_
INPUT?
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-16 13:38 ` Lee Jones
(?)
@ 2015-02-17 18:54 ` Fabio Estevam
-1 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-17 18:54 UTC (permalink / raw)
To: Lee Jones
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
>> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> + struct mx25_tsadc *tsadc)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + int irq;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0) {
>
> What if 0 is returned?
Then imx25.dtsi would be passing irq=0 for the ADC, which would be
totally wrong.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-17 18:54 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-17 18:54 UTC (permalink / raw)
To: Lee Jones
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> + struct mx25_tsadc *tsadc)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + int irq;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0) {
>
> What if 0 is returned?
Then imx25.dtsi would be passing irq=0 for the ADC, which would be
totally wrong.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-17 18:54 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-17 18:54 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> + struct mx25_tsadc *tsadc)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + int irq;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0) {
>
> What if 0 is returned?
Then imx25.dtsi would be passing irq=0 for the ADC, which would be
totally wrong.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-01-24 14:01 ` Markus Pargmann
(?)
@ 2015-02-17 19:14 ` Uwe Kleine-König
-1 siblings, 0 replies; 50+ messages in thread
From: Uwe Kleine-König @ 2015-02-17 19:14 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack, Mark Rutland,
devicetree-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
Eric Bénard, Pawel Moll, Ian Campbell,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Kumar Gala, Denis Carikli,
Rob Herring, Sascha Hauer, linux-input-u79uwXL29TY76Z2rM5mHXA,
Lee Jones, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hello Markus,
On Sat, Jan 24, 2015 at 03:01:38PM +0100, Markus Pargmann wrote:
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
Can you make that:
depends on SOC_IMX25 || COMPILE_TEST
?
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
Which version of the GPL is your code licensed under?
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> [...]
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
Do you need to reverse the order of these two calls to prevent the
handler being called while handler_data is still unset?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-17 19:14 ` Uwe Kleine-König
0 siblings, 0 replies; 50+ messages in thread
From: Uwe Kleine-König @ 2015-02-17 19:14 UTC (permalink / raw)
To: Markus Pargmann
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack, Mark Rutland,
devicetree, Lars-Peter Clausen, Eric Bénard, Pawel Moll,
Ian Campbell, linux-iio, Kumar Gala, Denis Carikli, Rob Herring,
Sascha Hauer, linux-input, Lee Jones, linux-arm-kernel
Hello Markus,
On Sat, Jan 24, 2015 at 03:01:38PM +0100, Markus Pargmann wrote:
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
Can you make that:
depends on SOC_IMX25 || COMPILE_TEST
?
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
Which version of the GPL is your code licensed under?
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> [...]
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
Do you need to reverse the order of these two calls to prevent the
handler being called while handler_data is still unset?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-17 19:14 ` Uwe Kleine-König
0 siblings, 0 replies; 50+ messages in thread
From: Uwe Kleine-König @ 2015-02-17 19:14 UTC (permalink / raw)
To: linux-arm-kernel
Hello Markus,
On Sat, Jan 24, 2015 at 03:01:38PM +0100, Markus Pargmann wrote:
> +config MFD_MX25_TSADC
> + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> + select REGMAP_MMIO
> + depends on SOC_IMX25
Can you make that:
depends on SOC_IMX25 || COMPILE_TEST
?
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
Which version of the GPL is your code licensed under?
> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> + struct mx25_tsadc *tsadc)
> [...]
> + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> + irq_set_handler_data(irq, tsadc);
Do you need to reverse the order of these two calls to prevent the
handler being called while handler_data is still unset?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-17 18:54 ` Fabio Estevam
(?)
@ 2015-02-18 8:01 ` Lee Jones
-1 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 8:01 UTC (permalink / raw)
To: Fabio Estevam
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Tue, 17 Feb 2015, Fabio Estevam wrote:
> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>
> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> + struct mx25_tsadc *tsadc)
> >> +{
> >> + struct device *dev = &pdev->dev;
> >> + struct device_node *np = dev->of_node;
> >> + int irq;
> >> +
> >> + irq = platform_get_irq(pdev, 0);
> >> + if (irq < 0) {
> >
> > What if 0 is returned?
>
> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> totally wrong.
Exactly, so it should be <=.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 8:01 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 8:01 UTC (permalink / raw)
To: Fabio Estevam
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Tue, 17 Feb 2015, Fabio Estevam wrote:
> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>
> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> + struct mx25_tsadc *tsadc)
> >> +{
> >> + struct device *dev = &pdev->dev;
> >> + struct device_node *np = dev->of_node;
> >> + int irq;
> >> +
> >> + irq = platform_get_irq(pdev, 0);
> >> + if (irq < 0) {
> >
> > What if 0 is returned?
>
> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> totally wrong.
Exactly, so it should be <=.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 8:01 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 8:01 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, 17 Feb 2015, Fabio Estevam wrote:
> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>
> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> + struct mx25_tsadc *tsadc)
> >> +{
> >> + struct device *dev = &pdev->dev;
> >> + struct device_node *np = dev->of_node;
> >> + int irq;
> >> +
> >> + irq = platform_get_irq(pdev, 0);
> >> + if (irq < 0) {
> >
> > What if 0 is returned?
>
> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> totally wrong.
Exactly, so it should be <=.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-18 8:01 ` Lee Jones
(?)
@ 2015-02-18 11:57 ` Fabio Estevam
-1 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-18 11:57 UTC (permalink / raw)
To: Lee Jones
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-input-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA, Lars-Peter Clausen,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala
On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
> On Tue, 17 Feb 2015, Fabio Estevam wrote:
>
>> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> wrote:
>>
>> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> >> + struct mx25_tsadc *tsadc)
>> >> +{
>> >> + struct device *dev = &pdev->dev;
>> >> + struct device_node *np = dev->of_node;
>> >> + int irq;
>> >> +
>> >> + irq = platform_get_irq(pdev, 0);
>> >> + if (irq < 0) {
>> >
>> > What if 0 is returned?
>>
>> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
>> totally wrong.
>
> Exactly, so it should be <=.
imx25.dtsi passes interrupts = <46>; for the touch screen controller,
so the irq number will never be zero.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 11:57 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-18 11:57 UTC (permalink / raw)
To: Lee Jones
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Tue, 17 Feb 2015, Fabio Estevam wrote:
>
>> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>>
>> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> >> + struct mx25_tsadc *tsadc)
>> >> +{
>> >> + struct device *dev = &pdev->dev;
>> >> + struct device_node *np = dev->of_node;
>> >> + int irq;
>> >> +
>> >> + irq = platform_get_irq(pdev, 0);
>> >> + if (irq < 0) {
>> >
>> > What if 0 is returned?
>>
>> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
>> totally wrong.
>
> Exactly, so it should be <=.
imx25.dtsi passes interrupts = <46>; for the touch screen controller,
so the irq number will never be zero.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 11:57 ` Fabio Estevam
0 siblings, 0 replies; 50+ messages in thread
From: Fabio Estevam @ 2015-02-18 11:57 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> On Tue, 17 Feb 2015, Fabio Estevam wrote:
>
>> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
>>
>> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
>> >> + struct mx25_tsadc *tsadc)
>> >> +{
>> >> + struct device *dev = &pdev->dev;
>> >> + struct device_node *np = dev->of_node;
>> >> + int irq;
>> >> +
>> >> + irq = platform_get_irq(pdev, 0);
>> >> + if (irq < 0) {
>> >
>> > What if 0 is returned?
>>
>> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
>> totally wrong.
>
> Exactly, so it should be <=.
imx25.dtsi passes interrupts = <46>; for the touch screen controller,
so the irq number will never be zero.
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-18 11:57 ` Fabio Estevam
(?)
@ 2015-02-18 12:08 ` Lee Jones
-1 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 12:08 UTC (permalink / raw)
To: Fabio Estevam
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Wed, 18 Feb 2015, Fabio Estevam wrote:
> On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Tue, 17 Feb 2015, Fabio Estevam wrote:
> >
> >> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> >> + struct mx25_tsadc *tsadc)
> >> >> +{
> >> >> + struct device *dev = &pdev->dev;
> >> >> + struct device_node *np = dev->of_node;
> >> >> + int irq;
> >> >> +
> >> >> + irq = platform_get_irq(pdev, 0);
> >> >> + if (irq < 0) {
> >> >
> >> > What if 0 is returned?
> >>
> >> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> >> totally wrong.
> >
> > Exactly, so it should be <=.
>
> imx25.dtsi passes interrupts = <46>; for the touch screen controller,
> so the irq number will never be zero.
It doesn't matter what happens to be passed at the moment. The
correct thing to do is enforce correct/full error checking. Yes <0 is
an error, but so is =0, so encompass it in the checks.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 12:08 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 12:08 UTC (permalink / raw)
To: Fabio Estevam
Cc: Markus Pargmann, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
On Wed, 18 Feb 2015, Fabio Estevam wrote:
> On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Tue, 17 Feb 2015, Fabio Estevam wrote:
> >
> >> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> >> + struct mx25_tsadc *tsadc)
> >> >> +{
> >> >> + struct device *dev = &pdev->dev;
> >> >> + struct device_node *np = dev->of_node;
> >> >> + int irq;
> >> >> +
> >> >> + irq = platform_get_irq(pdev, 0);
> >> >> + if (irq < 0) {
> >> >
> >> > What if 0 is returned?
> >>
> >> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> >> totally wrong.
> >
> > Exactly, so it should be <=.
>
> imx25.dtsi passes interrupts = <46>; for the touch screen controller,
> so the irq number will never be zero.
It doesn't matter what happens to be passed at the moment. The
correct thing to do is enforce correct/full error checking. Yes <0 is
an error, but so is =0, so encompass it in the checks.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-18 12:08 ` Lee Jones
0 siblings, 0 replies; 50+ messages in thread
From: Lee Jones @ 2015-02-18 12:08 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, 18 Feb 2015, Fabio Estevam wrote:
> On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > On Tue, 17 Feb 2015, Fabio Estevam wrote:
> >
> >> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
> >>
> >> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> >> >> + struct mx25_tsadc *tsadc)
> >> >> +{
> >> >> + struct device *dev = &pdev->dev;
> >> >> + struct device_node *np = dev->of_node;
> >> >> + int irq;
> >> >> +
> >> >> + irq = platform_get_irq(pdev, 0);
> >> >> + if (irq < 0) {
> >> >
> >> > What if 0 is returned?
> >>
> >> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> >> totally wrong.
> >
> > Exactly, so it should be <=.
>
> imx25.dtsi passes interrupts = <46>; for the touch screen controller,
> so the irq number will never be zero.
It doesn't matter what happens to be passed at the moment. The
correct thing to do is enforce correct/full error checking. Yes <0 is
an error, but so is =0, so encompass it in the checks.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-18 12:08 ` Lee Jones
@ 2015-02-26 15:32 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-02-26 15:32 UTC (permalink / raw)
To: Lee Jones
Cc: Fabio Estevam, Shawn Guo, Samuel Ortiz, Dmitry Torokhov,
Jonathan Cameron, Peter Meerwald, Hartmut Knaack, Denis Carikli,
Eric Bénard, Sascha Hauer, linux-arm-kernel, linux-input,
linux-iio, Lars-Peter Clausen, devicetree, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala
[-- Attachment #1: Type: text/plain, Size: 1668 bytes --]
On Wed, Feb 18, 2015 at 12:08:44PM +0000, Lee Jones wrote:
> On Wed, 18 Feb 2015, Fabio Estevam wrote:
>
> > On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > > On Tue, 17 Feb 2015, Fabio Estevam wrote:
> > >
> > >> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > >>
> > >> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> > >> >> + struct mx25_tsadc *tsadc)
> > >> >> +{
> > >> >> + struct device *dev = &pdev->dev;
> > >> >> + struct device_node *np = dev->of_node;
> > >> >> + int irq;
> > >> >> +
> > >> >> + irq = platform_get_irq(pdev, 0);
> > >> >> + if (irq < 0) {
> > >> >
> > >> > What if 0 is returned?
> > >>
> > >> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> > >> totally wrong.
> > >
> > > Exactly, so it should be <=.
> >
> > imx25.dtsi passes interrupts = <46>; for the touch screen controller,
> > so the irq number will never be zero.
>
> It doesn't matter what happens to be passed at the moment. The
> correct thing to do is enforce correct/full error checking. Yes <0 is
> an error, but so is =0, so encompass it in the checks.
I now changed all irq < 0 checks to irq <= 0 under the assumption that
irq 0 is always an error.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-02-26 15:32 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-02-26 15:32 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Feb 18, 2015 at 12:08:44PM +0000, Lee Jones wrote:
> On Wed, 18 Feb 2015, Fabio Estevam wrote:
>
> > On Wed, Feb 18, 2015 at 6:01 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > > On Tue, 17 Feb 2015, Fabio Estevam wrote:
> > >
> > >> On Mon, Feb 16, 2015 at 11:38 AM, Lee Jones <lee.jones@linaro.org> wrote:
> > >>
> > >> >> +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> > >> >> + struct mx25_tsadc *tsadc)
> > >> >> +{
> > >> >> + struct device *dev = &pdev->dev;
> > >> >> + struct device_node *np = dev->of_node;
> > >> >> + int irq;
> > >> >> +
> > >> >> + irq = platform_get_irq(pdev, 0);
> > >> >> + if (irq < 0) {
> > >> >
> > >> > What if 0 is returned?
> > >>
> > >> Then imx25.dtsi would be passing irq=0 for the ADC, which would be
> > >> totally wrong.
> > >
> > > Exactly, so it should be <=.
> >
> > imx25.dtsi passes interrupts = <46>; for the touch screen controller,
> > so the irq number will never be zero.
>
> It doesn't matter what happens to be passed at the moment. The
> correct thing to do is enforce correct/full error checking. Yes <0 is
> an error, but so is =0, so encompass it in the checks.
I now changed all irq < 0 checks to irq <= 0 under the assumption that
irq 0 is always an error.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150226/1944dc3f/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
2015-02-17 19:14 ` Uwe Kleine-König
@ 2015-03-02 19:12 ` Markus Pargmann
-1 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-03-02 19:12 UTC (permalink / raw)
To: Uwe Kleine-König
Cc: Shawn Guo, Samuel Ortiz, Dmitry Torokhov, Jonathan Cameron,
Fabio Estevam, Peter Meerwald, Hartmut Knaack, Mark Rutland,
devicetree, Lars-Peter Clausen, Eric Bénard, Pawel Moll,
Ian Campbell, linux-iio, Kumar Gala, Denis Carikli, Rob Herring,
Sascha Hauer, linux-input, Lee Jones, linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1561 bytes --]
Hi,
On Tue, Feb 17, 2015 at 08:14:38PM +0100, Uwe Kleine-König wrote:
> Hello Markus,
>
> On Sat, Jan 24, 2015 at 03:01:38PM +0100, Markus Pargmann wrote:
> > +config MFD_MX25_TSADC
> > + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> > + select REGMAP_MMIO
> > + depends on SOC_IMX25
> Can you make that:
>
> depends on SOC_IMX25 || COMPILE_TEST
>
> ?
Yes, changed.
>
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> Which version of the GPL is your code licensed under?
GPLv2 as described by MODULE_LICENSE. Will change the header
accordingly.
>
> > +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> > + struct mx25_tsadc *tsadc)
> > [...]
> > + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> > + irq_set_handler_data(irq, tsadc);
> Do you need to reverse the order of these two calls to prevent the
> handler being called while handler_data is still unset?
Yes that's probably better although the subdevices which may cause
interrupts here are not populated at this point.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver
@ 2015-03-02 19:12 ` Markus Pargmann
0 siblings, 0 replies; 50+ messages in thread
From: Markus Pargmann @ 2015-03-02 19:12 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Tue, Feb 17, 2015 at 08:14:38PM +0100, Uwe Kleine-K?nig wrote:
> Hello Markus,
>
> On Sat, Jan 24, 2015 at 03:01:38PM +0100, Markus Pargmann wrote:
> > +config MFD_MX25_TSADC
> > + tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
> > + select REGMAP_MMIO
> > + depends on SOC_IMX25
> Can you make that:
>
> depends on SOC_IMX25 || COMPILE_TEST
>
> ?
Yes, changed.
>
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 or later at the following locations:
> Which version of the GPL is your code licensed under?
GPLv2 as described by MODULE_LICENSE. Will change the header
accordingly.
>
> > +static int mx25_tsadc_setup_irq(struct platform_device *pdev,
> > + struct mx25_tsadc *tsadc)
> > [...]
> > + irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
> > + irq_set_handler_data(irq, tsadc);
> Do you need to reverse the order of these two calls to prevent the
> handler being called while handler_data is still unset?
Yes that's probably better although the subdevices which may cause
interrupts here are not populated at this point.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150302/29932a84/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
end of thread, other threads:[~2015-03-02 19:12 UTC | newest]
Thread overview: 50+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-01-24 14:01 [PATCH v5 0/6] imx25 adc and touchscreen driver Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
2015-01-24 14:01 ` [PATCH v5 1/6] mfd: fsl imx25 Touchscreen ADC driver Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
[not found] ` <1422108103-15052-2-git-send-email-mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-02-16 13:38 ` Lee Jones
2015-02-16 13:38 ` Lee Jones
2015-02-16 13:38 ` Lee Jones
2015-02-17 18:54 ` Fabio Estevam
2015-02-17 18:54 ` Fabio Estevam
2015-02-17 18:54 ` Fabio Estevam
2015-02-18 8:01 ` Lee Jones
2015-02-18 8:01 ` Lee Jones
2015-02-18 8:01 ` Lee Jones
2015-02-18 11:57 ` Fabio Estevam
2015-02-18 11:57 ` Fabio Estevam
2015-02-18 11:57 ` Fabio Estevam
2015-02-18 12:08 ` Lee Jones
2015-02-18 12:08 ` Lee Jones
2015-02-18 12:08 ` Lee Jones
2015-02-26 15:32 ` Markus Pargmann
2015-02-26 15:32 ` Markus Pargmann
2015-02-17 19:14 ` Uwe Kleine-König
2015-02-17 19:14 ` Uwe Kleine-König
2015-02-17 19:14 ` Uwe Kleine-König
2015-03-02 19:12 ` Markus Pargmann
2015-03-02 19:12 ` Markus Pargmann
2015-01-24 14:01 ` [PATCH v5 2/6] ARM: dt: Binding documentation for imx25 ADC/TSC Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
2015-01-24 14:01 ` [PATCH v5 3/6] iio: adc: fsl,imx25-gcq driver Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
2015-01-27 20:30 ` Jonathan Cameron
2015-01-27 20:30 ` Jonathan Cameron
[not found] ` <54C7F580.1030901-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2015-01-29 10:11 ` Markus Pargmann
2015-01-29 10:11 ` Markus Pargmann
2015-01-29 10:11 ` Markus Pargmann
[not found] ` <20150129101104.GE27422-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-02-08 11:56 ` Jonathan Cameron
2015-02-08 11:56 ` Jonathan Cameron
2015-02-08 11:56 ` Jonathan Cameron
[not found] ` <1422108103-15052-4-git-send-email-mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-01-29 14:51 ` Fabio Estevam
2015-01-29 14:51 ` Fabio Estevam
2015-01-29 14:51 ` Fabio Estevam
2015-01-30 7:27 ` Markus Pargmann
2015-01-30 7:27 ` Markus Pargmann
2015-01-24 14:01 ` [PATCH v5 4/6] input: touchscreen: imx25 tcq driver Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
[not found] ` <1422108103-15052-1-git-send-email-mpa-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-01-24 14:01 ` [PATCH v5 5/6] ARM: dts: imx25: Add TSC and ADC support Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
2015-01-24 14:01 ` [PATCH v5 6/6] ARM: imx_v4_v5_defconfig: Add I.MX25 Touchscreen controller " Markus Pargmann
2015-01-24 14:01 ` Markus Pargmann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.