[PATCH RESEND V4 0/4] i2c: busses: xgene: I2C proxy driver for X-Gene

[PATCH RESEND V4 0/4] i2c: busses: xgene: I2C proxy driver for X-Gene

[Feng Kan]

This is a proxy I2C driver for APM X-Gene SoC. It uses the mailbox driver
to tunnel i2c transactions via the SLIMpro processor.

V4 Change:
	- Remove PRP0001 and use a real ACPI id
V3 Change:
	- Add ACPI support
	- Fix previous comments.

Feng Kan (4):
  i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform
  i2c: busses: xgene: add acpi support for i2c xgene SLIMpro driver
  Documentation: i2c: Add APM X-Gene platform SLIMpro I2C driver
    documentation
  arm64: dts: add proxy I2C device driver on APM X-Gene platform

 .../devicetree/bindings/i2c/i2c-xgene-slimpro.txt  |  15 +
 arch/arm64/boot/dts/apm/apm-storm.dtsi             |   5 +
 drivers/i2c/busses/Kconfig                         |   9 +
 drivers/i2c/busses/Makefile                        |   1 +
 drivers/i2c/busses/i2c-xgene-slimpro.c             | 469 +++++++++++++++++++++
 5 files changed, 499 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt
 create mode 100644 drivers/i2c/busses/i2c-xgene-slimpro.c

-- 
1.9.1

[PATCH RESEND V4 1/4] i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform

[Feng Kan]

Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.

Signed-off-by: Feng Kan <fkan-qTEPVZfXA3Y@public.gmane.org>
Signed-off-by: Hieu Le <hnle-qTEPVZfXA3Y@public.gmane.org>
---
 drivers/i2c/busses/Kconfig             |   9 +
 drivers/i2c/busses/Makefile            |   1 +
 drivers/i2c/busses/i2c-xgene-slimpro.c | 459 +++++++++++++++++++++++++++++++++
 3 files changed, 469 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-xgene-slimpro.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 22da9c2..1ac07d0 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -1082,6 +1082,15 @@ config I2C_CROS_EC_TUNNEL
 	  connected there. This will work whatever the interface used to
 	  talk to the EC (SPI, I2C or LPC).
 
+config I2C_XGENE_SLIMPRO
+	tristate "APM X-Gene SoC I2C SLIMpro devices support"
+	depends on ARCH_XGENE && MAILBOX
+	help
+	  Enable I2C bus access using the APM X-Gene SoC SLIMpro
+	  co-processor. The I2C device access the I2C bus via the X-Gene
+	  to SLIMpro (On chip coprocessor) mailbox mechanism.
+	  If unsure, say N.
+
 config SCx200_ACB
 	tristate "Geode ACCESS.bus support"
 	depends on X86_32 && PCI
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 3638feb..9cf9c4b 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -107,6 +107,7 @@ obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_OPAL)		+= i2c-opal.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
+obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
 
 ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
diff --git a/drivers/i2c/busses/i2c-xgene-slimpro.c b/drivers/i2c/busses/i2c-xgene-slimpro.c
new file mode 100644
index 0000000..f994b8a0
--- /dev/null
+++ b/drivers/i2c/busses/i2c-xgene-slimpro.c
@@ -0,0 +1,459 @@
+/*
+ * X-Gene SLIMpro I2C Driver
+ *
+ * Copyright (c) 2014, Applied Micro Circuits Corporation
+ * Author: Feng Kan <fkan-qTEPVZfXA3Y@public.gmane.org>
+ * Author: Hieu Le <hnle-qTEPVZfXA3Y@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ *
+ * This driver provides support for X-Gene SLIMpro I2C device access
+ * using the APM X-Gene SLIMpro mailbox driver.
+ *
+ */
+#include <linux/dma-mapping.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/version.h>
+
+#define MAILBOX_OP_TIMEOUT		1000	/* Operation time out in ms */
+#define MAILBOX_I2C_INDEX		0
+#define SLIMPRO_IIC_BUS			1	/* Use I2C bus 1 only */
+
+#define SMBUS_CMD_LEN			1
+#define BYTE_DATA			1
+#define WORD_DATA			2
+#define BLOCK_DATA			3
+
+#define SLIMPRO_IIC_I2C_PROTOCOL	0
+#define SLIMPRO_IIC_SMB_PROTOCOL	1
+
+#define SLIMPRO_IIC_READ		0
+#define SLIMPRO_IIC_WRITE		1
+
+#define IIC_SMB_WITHOUT_DATA_LEN	0
+#define IIC_SMB_WITH_DATA_LEN		1
+
+#define SLIMPRO_DEBUG_MSG		0
+#define SLIMPRO_MSG_TYPE_SHIFT		28
+#define SLIMPRO_DBG_SUBTYPE_I2C1READ	4
+#define SLIMPRO_DBGMSG_TYPE_SHIFT	24
+#define SLIMPRO_DBGMSG_TYPE_MASK	0x0F000000U
+#define SLIMPRO_IIC_DEV_SHIFT		23
+#define SLIMPRO_IIC_DEV_MASK		0x00800000U
+#define SLIMPRO_IIC_DEVID_SHIFT		13
+#define SLIMPRO_IIC_DEVID_MASK		0x007FE000U
+#define SLIMPRO_IIC_RW_SHIFT		12
+#define SLIMPRO_IIC_RW_MASK		0x00001000U
+#define SLIMPRO_IIC_PROTO_SHIFT		11
+#define SLIMPRO_IIC_PROTO_MASK		0x00000800U
+#define SLIMPRO_IIC_ADDRLEN_SHIFT	8
+#define SLIMPRO_IIC_ADDRLEN_MASK	0x00000700U
+#define SLIMPRO_IIC_DATALEN_SHIFT	0
+#define SLIMPRO_IIC_DATALEN_MASK	0x000000FFU
+
+/*
+ * SLIMpro I2C message encode
+ *
+ * dev		- Controller number (0-based)
+ * chip		- I2C chip address
+ * op		- SLIMPRO_IIC_READ or SLIMPRO_IIC_WRITE
+ * proto	- SLIMPRO_IIC_SMB_PROTOCOL or SLIMPRO_IIC_I2C_PROTOCOL
+ * addrlen	- Length of the address field
+ * datalen	- Length of the data field
+ */
+#define SLIMPRO_IIC_ENCODE_MSG(dev, chip, op, proto, addrlen, datalen) \
+	((SLIMPRO_DEBUG_MSG << SLIMPRO_MSG_TYPE_SHIFT) | \
+	((SLIMPRO_DBG_SUBTYPE_I2C1READ << SLIMPRO_DBGMSG_TYPE_SHIFT) & \
+	SLIMPRO_DBGMSG_TYPE_MASK) | \
+	((dev << SLIMPRO_IIC_DEV_SHIFT) & SLIMPRO_IIC_DEV_MASK) | \
+	((chip << SLIMPRO_IIC_DEVID_SHIFT) & SLIMPRO_IIC_DEVID_MASK) | \
+	((op << SLIMPRO_IIC_RW_SHIFT) & SLIMPRO_IIC_RW_MASK) | \
+	((proto << SLIMPRO_IIC_PROTO_SHIFT) & SLIMPRO_IIC_PROTO_MASK) | \
+	((addrlen << SLIMPRO_IIC_ADDRLEN_SHIFT) & SLIMPRO_IIC_ADDRLEN_MASK) | \
+	((datalen << SLIMPRO_IIC_DATALEN_SHIFT) & SLIMPRO_IIC_DATALEN_MASK))
+
+/*
+ * Encode for upper address for block data
+ */
+#define SLIMPRO_IIC_ENCODE_FLAG_BUFADDR			0x80000000
+#define SLIMPRO_IIC_ENCODE_FLAG_WITH_DATA_LEN(a)	((u32) (((a) << 30) \
+								& 0x40000000))
+#define SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(a)		((u32) (((a) >> 12) \
+								& 0x3FF00000))
+#define SLIMPRO_IIC_ENCODE_ADDR(a)			((a) & 0x000FFFFF)
+
+struct slimpro_i2c_dev {
+	struct i2c_adapter adapter;
+	struct device *dev;
+	struct mbox_chan *mbox_chan;
+	struct mbox_client mbox_client;
+	struct completion rd_complete;
+	u8 dma_buffer[I2C_SMBUS_BLOCK_MAX];
+	u32 *resp_msg;
+};
+
+#define to_slimpro_i2c_dev(cl)	\
+		container_of(cl, struct slimpro_i2c_dev, mbox_client)
+
+static void slimpro_i2c_rx_cb(struct mbox_client *cl, void *mssg)
+{
+	struct slimpro_i2c_dev *ctx = to_slimpro_i2c_dev(cl);
+
+	/*
+	 * Response message format:
+	 * mssg[0] is the return code of the operation
+	 * mssg[1] is the first data word
+	 * mssg[2] is NOT used
+	 */
+	if (ctx->resp_msg)
+		*ctx->resp_msg = ((u32 *)mssg)[1];
+
+	if (ctx->mbox_client.tx_block)
+		complete(&ctx->rd_complete);
+}
+
+static int start_i2c_msg_xfer(struct slimpro_i2c_dev *ctx)
+{
+	if (ctx->mbox_client.tx_block) {
+		if (!wait_for_completion_timeout(&ctx->rd_complete,
+						 msecs_to_jiffies(MAILBOX_OP_TIMEOUT)))
+			return -ETIMEDOUT;
+	}
+
+	/* Check of invalid data or no device */
+	if (*ctx->resp_msg == 0xffffffff)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int slimpro_i2c_rd(struct slimpro_i2c_dev *ctx, u32 chip,
+			  u32 addr, u32 addrlen, u32 protocol,
+			  u32 readlen, u32 *data)
+{
+	u32 msg[3];
+	int rc;
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip,
+					SLIMPRO_IIC_READ, protocol, addrlen, readlen);
+	msg[1] = SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = 0;
+	ctx->resp_msg = data;
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err;
+
+	rc = start_i2c_msg_xfer(ctx);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_wr(struct slimpro_i2c_dev *ctx, u32 chip,
+			  u32 addr, u32 addrlen, u32 protocol, u32 writelen,
+			  u32 data)
+{
+	u32 msg[3];
+	int rc;
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip,
+					SLIMPRO_IIC_WRITE, protocol, addrlen, writelen);
+	msg[1] = SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = data;
+	ctx->resp_msg = msg;
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err;
+
+	rc = start_i2c_msg_xfer(ctx);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_blkrd(struct slimpro_i2c_dev *ctx, u32 chip, u32 addr,
+			     u32 addrlen, u32 protocol, u32 readlen,
+			     u32 with_data_len, void *data)
+{
+	dma_addr_t paddr;
+	u32 msg[3];
+	int rc;
+
+	paddr = dma_map_single(ctx->dev, ctx->dma_buffer, readlen, DMA_FROM_DEVICE);
+	rc = dma_mapping_error(ctx->dev, paddr);
+	if (rc) {
+		dev_err(&ctx->adapter.dev, "Error in mapping dma buffer %p\n",
+			ctx->dma_buffer);
+		goto err;
+	}
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip, SLIMPRO_IIC_READ,
+					protocol, addrlen, readlen);
+	msg[1] = SLIMPRO_IIC_ENCODE_FLAG_BUFADDR |
+		 SLIMPRO_IIC_ENCODE_FLAG_WITH_DATA_LEN(with_data_len) |
+		 SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(paddr) |
+		 SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = (u32)paddr;
+	ctx->resp_msg = msg;
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err_unmap;
+
+	rc = start_i2c_msg_xfer(ctx);
+
+	/* Copy to destination */
+	memcpy(data, ctx->dma_buffer, readlen);
+
+err_unmap:
+	dma_unmap_single(ctx->dev, paddr, readlen, DMA_FROM_DEVICE);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_blkwr(struct slimpro_i2c_dev *ctx, u32 chip,
+			     u32 addr, u32 addrlen, u32 protocol, u32 writelen,
+			     void *data)
+{
+	dma_addr_t paddr;
+	u32 msg[3];
+	int rc;
+
+	memcpy(ctx->dma_buffer, data, writelen);
+	paddr = dma_map_single(ctx->dev, ctx->dma_buffer, writelen,
+			       DMA_TO_DEVICE);
+	rc = dma_mapping_error(ctx->dev, paddr);
+	if (rc) {
+		dev_err(&ctx->adapter.dev, "Error in mapping dma buffer %p\n",
+			ctx->dma_buffer);
+		goto err;
+	}
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip, SLIMPRO_IIC_WRITE,
+					protocol, addrlen, writelen);
+	msg[1] = SLIMPRO_IIC_ENCODE_FLAG_BUFADDR |
+		 SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(paddr) |
+		 SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = (u32)paddr;
+	ctx->resp_msg = msg;
+
+	if (ctx->mbox_client.tx_block)
+		reinit_completion(&ctx->rd_complete);
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err_unmap;
+
+	rc = start_i2c_msg_xfer(ctx);
+
+err_unmap:
+	dma_unmap_single(ctx->dev, paddr, writelen, DMA_TO_DEVICE);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int xgene_slimpro_i2c_xfer(struct i2c_adapter *adap, u16 addr,
+				  unsigned short flags, char read_write,
+				  u8 command, int size,
+				  union i2c_smbus_data *data)
+{
+	struct slimpro_i2c_dev *ctx = i2c_get_adapdata(adap);
+	int ret = -EOPNOTSUPP;
+	u32 val;
+
+	switch (size) {
+	case I2C_SMBUS_BYTE:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, 0, 0,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, &val);
+			data->byte = val;
+		} else {
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     0, 0);
+		}
+		break;
+	case I2C_SMBUS_BYTE_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, &val);
+			data->byte = val;
+		} else {
+			val = data->byte;
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, val);
+		}
+		break;
+	case I2C_SMBUS_WORD_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     WORD_DATA, &val);
+			data->word = val;
+		} else {
+			val = data->word;
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     WORD_DATA, val);
+		}
+		break;
+	case I2C_SMBUS_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_blkrd(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_SMB_PROTOCOL,
+						I2C_SMBUS_BLOCK_MAX + 1,
+						IIC_SMB_WITH_DATA_LEN,
+						&data->block[0]);
+
+		} else {
+			ret = slimpro_i2c_blkwr(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_SMB_PROTOCOL,
+						data->block[0] + 1,
+						&data->block[0]);
+		}
+		break;
+	case I2C_SMBUS_I2C_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_blkrd(ctx, addr,
+						command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_I2C_PROTOCOL,
+						I2C_SMBUS_BLOCK_MAX,
+						IIC_SMB_WITHOUT_DATA_LEN,
+						&data->block[1]);
+		} else {
+			ret = slimpro_i2c_blkwr(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_I2C_PROTOCOL,
+						data->block[0],
+						&data->block[1]);
+		}
+		break;
+	default:
+		break;
+	}
+	return ret;
+}
+
+/*
+* Return list of supported functionality.
+*/
+static u32 xgene_slimpro_i2c_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_SMBUS_BYTE |
+		I2C_FUNC_SMBUS_BYTE_DATA |
+		I2C_FUNC_SMBUS_WORD_DATA |
+		I2C_FUNC_SMBUS_BLOCK_DATA |
+		I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static struct i2c_algorithm xgene_slimpro_i2c_algorithm = {
+	.smbus_xfer = xgene_slimpro_i2c_xfer,
+	.functionality = xgene_slimpro_i2c_func,
+};
+
+static int __init xgene_slimpro_i2c_probe(struct platform_device *pdev)
+{
+	struct slimpro_i2c_dev *ctx;
+	struct i2c_adapter *adapter;
+	struct mbox_client *cl;
+	int rc;
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->dev = &pdev->dev;
+	platform_set_drvdata(pdev, ctx);
+	cl = &ctx->mbox_client;
+
+	/* Request mailbox channel */
+	cl->dev = &pdev->dev;
+	cl->rx_callback = slimpro_i2c_rx_cb;
+	cl->tx_block = true;
+	init_completion(&ctx->rd_complete);
+	cl->tx_tout = MAILBOX_OP_TIMEOUT;
+	cl->knows_txdone = false;
+	ctx->mbox_chan = mbox_request_channel(cl, MAILBOX_I2C_INDEX);
+	if (IS_ERR(ctx->mbox_chan)) {
+		dev_err(&pdev->dev, "i2c mailbox channel request failed\n");
+		return PTR_ERR(ctx->mbox_chan);
+	}
+
+	rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (rc)
+		dev_warn(&pdev->dev, "Unable to set dma mask\n");
+
+	/* Setup I2C adapter */
+	adapter = &ctx->adapter;
+	snprintf(adapter->name, sizeof(adapter->name), "MAILBOX I2C");
+	adapter->algo = &xgene_slimpro_i2c_algorithm;
+	adapter->class = I2C_CLASS_HWMON;
+	adapter->dev.parent = &pdev->dev;
+	i2c_set_adapdata(adapter, ctx);
+	rc = i2c_add_adapter(adapter);
+	if (rc) {
+		dev_err(&pdev->dev, "Adapter registeration failed\n");
+		return rc;
+	}
+
+	dev_info(&pdev->dev, "Mailbox I2C Adapter registered\n");
+	return 0;
+}
+
+static int xgene_slimpro_i2c_remove(struct platform_device *pdev)
+{
+	struct slimpro_i2c_dev *ctx = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&ctx->adapter);
+
+	mbox_free_channel(ctx->mbox_chan);
+
+	return 0;
+}
+
+static const struct of_device_id xgene_slimpro_i2c_dt_ids[] = {
+	{.compatible = "apm,xgene-slimpro-i2c" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xgene_slimpro_i2c_dt_ids);
+
+static struct platform_driver xgene_slimpro_i2c_driver = {
+	.probe	= xgene_slimpro_i2c_probe,
+	.remove	= xgene_slimpro_i2c_remove,
+	.driver	= {
+		.name	= "xgene-slimpro-i2c",
+		.of_match_table = of_match_ptr(xgene_slimpro_i2c_dt_ids),
+	},
+};
+
+module_platform_driver(xgene_slimpro_i2c_driver);
+
+MODULE_DESCRIPTION("APM X-Gene SLIMpro I2C driver");
+MODULE_AUTHOR("Feng Kan <fkan-qTEPVZfXA3Y@public.gmane.org>");
+MODULE_AUTHOR("Hieu Le <hnle-qTEPVZfXA3Y@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH RESEND V4 1/4] i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform

[Feng Kan]

Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
---
 drivers/i2c/busses/Kconfig             |   9 +
 drivers/i2c/busses/Makefile            |   1 +
 drivers/i2c/busses/i2c-xgene-slimpro.c | 459 +++++++++++++++++++++++++++++++++
 3 files changed, 469 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-xgene-slimpro.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 22da9c2..1ac07d0 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -1082,6 +1082,15 @@ config I2C_CROS_EC_TUNNEL
 	  connected there. This will work whatever the interface used to
 	  talk to the EC (SPI, I2C or LPC).
 
+config I2C_XGENE_SLIMPRO
+	tristate "APM X-Gene SoC I2C SLIMpro devices support"
+	depends on ARCH_XGENE && MAILBOX
+	help
+	  Enable I2C bus access using the APM X-Gene SoC SLIMpro
+	  co-processor. The I2C device access the I2C bus via the X-Gene
+	  to SLIMpro (On chip coprocessor) mailbox mechanism.
+	  If unsure, say N.
+
 config SCx200_ACB
 	tristate "Geode ACCESS.bus support"
 	depends on X86_32 && PCI
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 3638feb..9cf9c4b 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -107,6 +107,7 @@ obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_OPAL)		+= i2c-opal.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
+obj-$(CONFIG_I2C_XGENE_SLIMPRO) += i2c-xgene-slimpro.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
 
 ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
diff --git a/drivers/i2c/busses/i2c-xgene-slimpro.c b/drivers/i2c/busses/i2c-xgene-slimpro.c
new file mode 100644
index 0000000..f994b8a0
--- /dev/null
+++ b/drivers/i2c/busses/i2c-xgene-slimpro.c
@@ -0,0 +1,459 @@
+/*
+ * X-Gene SLIMpro I2C Driver
+ *
+ * Copyright (c) 2014, Applied Micro Circuits Corporation
+ * Author: Feng Kan <fkan@apm.com>
+ * Author: Hieu Le <hnle@apm.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ *
+ * This driver provides support for X-Gene SLIMpro I2C device access
+ * using the APM X-Gene SLIMpro mailbox driver.
+ *
+ */
+#include <linux/dma-mapping.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/version.h>
+
+#define MAILBOX_OP_TIMEOUT		1000	/* Operation time out in ms */
+#define MAILBOX_I2C_INDEX		0
+#define SLIMPRO_IIC_BUS			1	/* Use I2C bus 1 only */
+
+#define SMBUS_CMD_LEN			1
+#define BYTE_DATA			1
+#define WORD_DATA			2
+#define BLOCK_DATA			3
+
+#define SLIMPRO_IIC_I2C_PROTOCOL	0
+#define SLIMPRO_IIC_SMB_PROTOCOL	1
+
+#define SLIMPRO_IIC_READ		0
+#define SLIMPRO_IIC_WRITE		1
+
+#define IIC_SMB_WITHOUT_DATA_LEN	0
+#define IIC_SMB_WITH_DATA_LEN		1
+
+#define SLIMPRO_DEBUG_MSG		0
+#define SLIMPRO_MSG_TYPE_SHIFT		28
+#define SLIMPRO_DBG_SUBTYPE_I2C1READ	4
+#define SLIMPRO_DBGMSG_TYPE_SHIFT	24
+#define SLIMPRO_DBGMSG_TYPE_MASK	0x0F000000U
+#define SLIMPRO_IIC_DEV_SHIFT		23
+#define SLIMPRO_IIC_DEV_MASK		0x00800000U
+#define SLIMPRO_IIC_DEVID_SHIFT		13
+#define SLIMPRO_IIC_DEVID_MASK		0x007FE000U
+#define SLIMPRO_IIC_RW_SHIFT		12
+#define SLIMPRO_IIC_RW_MASK		0x00001000U
+#define SLIMPRO_IIC_PROTO_SHIFT		11
+#define SLIMPRO_IIC_PROTO_MASK		0x00000800U
+#define SLIMPRO_IIC_ADDRLEN_SHIFT	8
+#define SLIMPRO_IIC_ADDRLEN_MASK	0x00000700U
+#define SLIMPRO_IIC_DATALEN_SHIFT	0
+#define SLIMPRO_IIC_DATALEN_MASK	0x000000FFU
+
+/*
+ * SLIMpro I2C message encode
+ *
+ * dev		- Controller number (0-based)
+ * chip		- I2C chip address
+ * op		- SLIMPRO_IIC_READ or SLIMPRO_IIC_WRITE
+ * proto	- SLIMPRO_IIC_SMB_PROTOCOL or SLIMPRO_IIC_I2C_PROTOCOL
+ * addrlen	- Length of the address field
+ * datalen	- Length of the data field
+ */
+#define SLIMPRO_IIC_ENCODE_MSG(dev, chip, op, proto, addrlen, datalen) \
+	((SLIMPRO_DEBUG_MSG << SLIMPRO_MSG_TYPE_SHIFT) | \
+	((SLIMPRO_DBG_SUBTYPE_I2C1READ << SLIMPRO_DBGMSG_TYPE_SHIFT) & \
+	SLIMPRO_DBGMSG_TYPE_MASK) | \
+	((dev << SLIMPRO_IIC_DEV_SHIFT) & SLIMPRO_IIC_DEV_MASK) | \
+	((chip << SLIMPRO_IIC_DEVID_SHIFT) & SLIMPRO_IIC_DEVID_MASK) | \
+	((op << SLIMPRO_IIC_RW_SHIFT) & SLIMPRO_IIC_RW_MASK) | \
+	((proto << SLIMPRO_IIC_PROTO_SHIFT) & SLIMPRO_IIC_PROTO_MASK) | \
+	((addrlen << SLIMPRO_IIC_ADDRLEN_SHIFT) & SLIMPRO_IIC_ADDRLEN_MASK) | \
+	((datalen << SLIMPRO_IIC_DATALEN_SHIFT) & SLIMPRO_IIC_DATALEN_MASK))
+
+/*
+ * Encode for upper address for block data
+ */
+#define SLIMPRO_IIC_ENCODE_FLAG_BUFADDR			0x80000000
+#define SLIMPRO_IIC_ENCODE_FLAG_WITH_DATA_LEN(a)	((u32) (((a) << 30) \
+								& 0x40000000))
+#define SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(a)		((u32) (((a) >> 12) \
+								& 0x3FF00000))
+#define SLIMPRO_IIC_ENCODE_ADDR(a)			((a) & 0x000FFFFF)
+
+struct slimpro_i2c_dev {
+	struct i2c_adapter adapter;
+	struct device *dev;
+	struct mbox_chan *mbox_chan;
+	struct mbox_client mbox_client;
+	struct completion rd_complete;
+	u8 dma_buffer[I2C_SMBUS_BLOCK_MAX];
+	u32 *resp_msg;
+};
+
+#define to_slimpro_i2c_dev(cl)	\
+		container_of(cl, struct slimpro_i2c_dev, mbox_client)
+
+static void slimpro_i2c_rx_cb(struct mbox_client *cl, void *mssg)
+{
+	struct slimpro_i2c_dev *ctx = to_slimpro_i2c_dev(cl);
+
+	/*
+	 * Response message format:
+	 * mssg[0] is the return code of the operation
+	 * mssg[1] is the first data word
+	 * mssg[2] is NOT used
+	 */
+	if (ctx->resp_msg)
+		*ctx->resp_msg = ((u32 *)mssg)[1];
+
+	if (ctx->mbox_client.tx_block)
+		complete(&ctx->rd_complete);
+}
+
+static int start_i2c_msg_xfer(struct slimpro_i2c_dev *ctx)
+{
+	if (ctx->mbox_client.tx_block) {
+		if (!wait_for_completion_timeout(&ctx->rd_complete,
+						 msecs_to_jiffies(MAILBOX_OP_TIMEOUT)))
+			return -ETIMEDOUT;
+	}
+
+	/* Check of invalid data or no device */
+	if (*ctx->resp_msg == 0xffffffff)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int slimpro_i2c_rd(struct slimpro_i2c_dev *ctx, u32 chip,
+			  u32 addr, u32 addrlen, u32 protocol,
+			  u32 readlen, u32 *data)
+{
+	u32 msg[3];
+	int rc;
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip,
+					SLIMPRO_IIC_READ, protocol, addrlen, readlen);
+	msg[1] = SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = 0;
+	ctx->resp_msg = data;
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err;
+
+	rc = start_i2c_msg_xfer(ctx);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_wr(struct slimpro_i2c_dev *ctx, u32 chip,
+			  u32 addr, u32 addrlen, u32 protocol, u32 writelen,
+			  u32 data)
+{
+	u32 msg[3];
+	int rc;
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip,
+					SLIMPRO_IIC_WRITE, protocol, addrlen, writelen);
+	msg[1] = SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = data;
+	ctx->resp_msg = msg;
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err;
+
+	rc = start_i2c_msg_xfer(ctx);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_blkrd(struct slimpro_i2c_dev *ctx, u32 chip, u32 addr,
+			     u32 addrlen, u32 protocol, u32 readlen,
+			     u32 with_data_len, void *data)
+{
+	dma_addr_t paddr;
+	u32 msg[3];
+	int rc;
+
+	paddr = dma_map_single(ctx->dev, ctx->dma_buffer, readlen, DMA_FROM_DEVICE);
+	rc = dma_mapping_error(ctx->dev, paddr);
+	if (rc) {
+		dev_err(&ctx->adapter.dev, "Error in mapping dma buffer %p\n",
+			ctx->dma_buffer);
+		goto err;
+	}
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip, SLIMPRO_IIC_READ,
+					protocol, addrlen, readlen);
+	msg[1] = SLIMPRO_IIC_ENCODE_FLAG_BUFADDR |
+		 SLIMPRO_IIC_ENCODE_FLAG_WITH_DATA_LEN(with_data_len) |
+		 SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(paddr) |
+		 SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = (u32)paddr;
+	ctx->resp_msg = msg;
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err_unmap;
+
+	rc = start_i2c_msg_xfer(ctx);
+
+	/* Copy to destination */
+	memcpy(data, ctx->dma_buffer, readlen);
+
+err_unmap:
+	dma_unmap_single(ctx->dev, paddr, readlen, DMA_FROM_DEVICE);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int slimpro_i2c_blkwr(struct slimpro_i2c_dev *ctx, u32 chip,
+			     u32 addr, u32 addrlen, u32 protocol, u32 writelen,
+			     void *data)
+{
+	dma_addr_t paddr;
+	u32 msg[3];
+	int rc;
+
+	memcpy(ctx->dma_buffer, data, writelen);
+	paddr = dma_map_single(ctx->dev, ctx->dma_buffer, writelen,
+			       DMA_TO_DEVICE);
+	rc = dma_mapping_error(ctx->dev, paddr);
+	if (rc) {
+		dev_err(&ctx->adapter.dev, "Error in mapping dma buffer %p\n",
+			ctx->dma_buffer);
+		goto err;
+	}
+
+	msg[0] = SLIMPRO_IIC_ENCODE_MSG(SLIMPRO_IIC_BUS, chip, SLIMPRO_IIC_WRITE,
+					protocol, addrlen, writelen);
+	msg[1] = SLIMPRO_IIC_ENCODE_FLAG_BUFADDR |
+		 SLIMPRO_IIC_ENCODE_UPPER_BUFADDR(paddr) |
+		 SLIMPRO_IIC_ENCODE_ADDR(addr);
+	msg[2] = (u32)paddr;
+	ctx->resp_msg = msg;
+
+	if (ctx->mbox_client.tx_block)
+		reinit_completion(&ctx->rd_complete);
+
+	rc = mbox_send_message(ctx->mbox_chan, &msg);
+	if (rc < 0)
+		goto err_unmap;
+
+	rc = start_i2c_msg_xfer(ctx);
+
+err_unmap:
+	dma_unmap_single(ctx->dev, paddr, writelen, DMA_TO_DEVICE);
+err:
+	ctx->resp_msg = NULL;
+	return rc;
+}
+
+static int xgene_slimpro_i2c_xfer(struct i2c_adapter *adap, u16 addr,
+				  unsigned short flags, char read_write,
+				  u8 command, int size,
+				  union i2c_smbus_data *data)
+{
+	struct slimpro_i2c_dev *ctx = i2c_get_adapdata(adap);
+	int ret = -EOPNOTSUPP;
+	u32 val;
+
+	switch (size) {
+	case I2C_SMBUS_BYTE:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, 0, 0,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, &val);
+			data->byte = val;
+		} else {
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     0, 0);
+		}
+		break;
+	case I2C_SMBUS_BYTE_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, &val);
+			data->byte = val;
+		} else {
+			val = data->byte;
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     BYTE_DATA, val);
+		}
+		break;
+	case I2C_SMBUS_WORD_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_rd(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     WORD_DATA, &val);
+			data->word = val;
+		} else {
+			val = data->word;
+			ret = slimpro_i2c_wr(ctx, addr, command, SMBUS_CMD_LEN,
+					     SLIMPRO_IIC_SMB_PROTOCOL,
+					     WORD_DATA, val);
+		}
+		break;
+	case I2C_SMBUS_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_blkrd(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_SMB_PROTOCOL,
+						I2C_SMBUS_BLOCK_MAX + 1,
+						IIC_SMB_WITH_DATA_LEN,
+						&data->block[0]);
+
+		} else {
+			ret = slimpro_i2c_blkwr(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_SMB_PROTOCOL,
+						data->block[0] + 1,
+						&data->block[0]);
+		}
+		break;
+	case I2C_SMBUS_I2C_BLOCK_DATA:
+		if (read_write == I2C_SMBUS_READ) {
+			ret = slimpro_i2c_blkrd(ctx, addr,
+						command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_I2C_PROTOCOL,
+						I2C_SMBUS_BLOCK_MAX,
+						IIC_SMB_WITHOUT_DATA_LEN,
+						&data->block[1]);
+		} else {
+			ret = slimpro_i2c_blkwr(ctx, addr, command,
+						SMBUS_CMD_LEN,
+						SLIMPRO_IIC_I2C_PROTOCOL,
+						data->block[0],
+						&data->block[1]);
+		}
+		break;
+	default:
+		break;
+	}
+	return ret;
+}
+
+/*
+* Return list of supported functionality.
+*/
+static u32 xgene_slimpro_i2c_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_SMBUS_BYTE |
+		I2C_FUNC_SMBUS_BYTE_DATA |
+		I2C_FUNC_SMBUS_WORD_DATA |
+		I2C_FUNC_SMBUS_BLOCK_DATA |
+		I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static struct i2c_algorithm xgene_slimpro_i2c_algorithm = {
+	.smbus_xfer = xgene_slimpro_i2c_xfer,
+	.functionality = xgene_slimpro_i2c_func,
+};
+
+static int __init xgene_slimpro_i2c_probe(struct platform_device *pdev)
+{
+	struct slimpro_i2c_dev *ctx;
+	struct i2c_adapter *adapter;
+	struct mbox_client *cl;
+	int rc;
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->dev = &pdev->dev;
+	platform_set_drvdata(pdev, ctx);
+	cl = &ctx->mbox_client;
+
+	/* Request mailbox channel */
+	cl->dev = &pdev->dev;
+	cl->rx_callback = slimpro_i2c_rx_cb;
+	cl->tx_block = true;
+	init_completion(&ctx->rd_complete);
+	cl->tx_tout = MAILBOX_OP_TIMEOUT;
+	cl->knows_txdone = false;
+	ctx->mbox_chan = mbox_request_channel(cl, MAILBOX_I2C_INDEX);
+	if (IS_ERR(ctx->mbox_chan)) {
+		dev_err(&pdev->dev, "i2c mailbox channel request failed\n");
+		return PTR_ERR(ctx->mbox_chan);
+	}
+
+	rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
+	if (rc)
+		dev_warn(&pdev->dev, "Unable to set dma mask\n");
+
+	/* Setup I2C adapter */
+	adapter = &ctx->adapter;
+	snprintf(adapter->name, sizeof(adapter->name), "MAILBOX I2C");
+	adapter->algo = &xgene_slimpro_i2c_algorithm;
+	adapter->class = I2C_CLASS_HWMON;
+	adapter->dev.parent = &pdev->dev;
+	i2c_set_adapdata(adapter, ctx);
+	rc = i2c_add_adapter(adapter);
+	if (rc) {
+		dev_err(&pdev->dev, "Adapter registeration failed\n");
+		return rc;
+	}
+
+	dev_info(&pdev->dev, "Mailbox I2C Adapter registered\n");
+	return 0;
+}
+
+static int xgene_slimpro_i2c_remove(struct platform_device *pdev)
+{
+	struct slimpro_i2c_dev *ctx = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&ctx->adapter);
+
+	mbox_free_channel(ctx->mbox_chan);
+
+	return 0;
+}
+
+static const struct of_device_id xgene_slimpro_i2c_dt_ids[] = {
+	{.compatible = "apm,xgene-slimpro-i2c" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xgene_slimpro_i2c_dt_ids);
+
+static struct platform_driver xgene_slimpro_i2c_driver = {
+	.probe	= xgene_slimpro_i2c_probe,
+	.remove	= xgene_slimpro_i2c_remove,
+	.driver	= {
+		.name	= "xgene-slimpro-i2c",
+		.of_match_table = of_match_ptr(xgene_slimpro_i2c_dt_ids),
+	},
+};
+
+module_platform_driver(xgene_slimpro_i2c_driver);
+
+MODULE_DESCRIPTION("APM X-Gene SLIMpro I2C driver");
+MODULE_AUTHOR("Feng Kan <fkan@apm.com>");
+MODULE_AUTHOR("Hieu Le <hnle@apm.com>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

[PATCH RESEND V4 2/4] i2c: busses: xgene: add acpi support for i2c xgene SLIMpro driver

[Feng Kan]

This adds support for ACPI for the APM X-Gene I2C SLIMpro proxy
driver.

Signed-off-by: Feng Kan <fkan@apm.com>
---
 drivers/i2c/busses/i2c-xgene-slimpro.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/i2c/busses/i2c-xgene-slimpro.c b/drivers/i2c/busses/i2c-xgene-slimpro.c
index f994b8a0..0b33aa2e 100644
--- a/drivers/i2c/busses/i2c-xgene-slimpro.c
+++ b/drivers/i2c/busses/i2c-xgene-slimpro.c
@@ -22,6 +22,7 @@
  * using the APM X-Gene SLIMpro mailbox driver.
  *
  */
+#include <linux/acpi.h>
 #include <linux/dma-mapping.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
@@ -442,12 +443,21 @@ static const struct of_device_id xgene_slimpro_i2c_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, xgene_slimpro_i2c_dt_ids);
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id xgene_slimpro_i2c_acpi_ids[] = {
+	{"APMC0D40", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, xgene_slimpro_i2c_acpi_ids);
+#endif
+
 static struct platform_driver xgene_slimpro_i2c_driver = {
 	.probe	= xgene_slimpro_i2c_probe,
 	.remove	= xgene_slimpro_i2c_remove,
 	.driver	= {
 		.name	= "xgene-slimpro-i2c",
 		.of_match_table = of_match_ptr(xgene_slimpro_i2c_dt_ids),
+		.acpi_match_table = ACPI_PTR(xgene_slimpro_i2c_acpi_ids)
 	},
 };
 
-- 
1.9.1

[PATCH RESEND V4 3/4] Documentation: i2c: Add APM X-Gene platform SLIMpro I2C driver documentation

[Feng Kan]

Add APM X-Gene platform SLIMpro I2C driver documentation.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
---
 .../devicetree/bindings/i2c/i2c-xgene-slimpro.txt         | 15 +++++++++++++++
 1 file changed, 15 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt

diff --git a/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt
new file mode 100644
index 0000000..f6b2c20
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt
@@ -0,0 +1,15 @@
+APM X-Gene SLIMpro Mailbox I2C Driver
+
+An I2C controller accessed over the "SLIMpro" mailbox.
+
+Required properties :
+
+ - compatible : should be "apm,xgene-slimpro-i2c"
+ - mboxes : use the label reference for the mailbox as the first parameter.
+	    The second parameter is the channel number.
+
+Example :
+	i2cslimpro {
+		compatible = "apm,xgene-slimpro-i2c";
+		mboxes = <&mailbox 0>;
+	};
-- 
1.9.1

[PATCH RESEND V4 4/4] arm64: dts: add proxy I2C device driver on APM X-Gene platform

[Feng Kan]

Add proxy I2C device driver on APM X-Gene platform.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
---
 arch/arm64/boot/dts/apm/apm-storm.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/apm/apm-storm.dtsi b/arch/arm64/boot/dts/apm/apm-storm.dtsi
index 70c14fa..00ae4d8 100644
--- a/arch/arm64/boot/dts/apm/apm-storm.dtsi
+++ b/arch/arm64/boot/dts/apm/apm-storm.dtsi
@@ -483,6 +483,11 @@
 					<0x0 0x7 0x4>;
 		};
 
+		i2cslimpro {
+			compatible = "apm,xgene-slimpro-i2c";
+			mboxes = <&mailbox 0>;
+		};
+
 		serial0: serial@1c020000 {
 			status = "disabled";
 			device_type = "serial";
-- 
1.9.1

Re: [PATCH RESEND V4 0/4] i2c: busses: xgene: I2C proxy driver for X-Gene

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 161 bytes --]


> 	- Fix previous comments.

Next time, please specify what exactly you changed. This speeds up
reviewing *a lot*, because otherwise I have to do this myself.


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 1/4] i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 668 bytes --]

On Fri, Apr 24, 2015 at 03:17:50PM -0700, Feng Kan wrote:
> Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
> device driver use the SLIMpro Mailbox driver to tunnel message to
> the SLIMpro coprocessor to do the work of accessing I2C components.
> 
> Signed-off-by: Feng Kan <fkan-qTEPVZfXA3Y@public.gmane.org>
> Signed-off-by: Hieu Le <hnle-qTEPVZfXA3Y@public.gmane.org>

Applied to for-next, thanks!

One comment though:

> +	adapter->class = I2C_CLASS_HWMON;

Since you have DT and ACPI, you most likely won't need that, or?
It speeds up boot time if you don't use classes. Send me an incremental
patch if you want to change this.


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 1/4] i2c: busses: add SLIMpro I2C device driver on APM X-Gene platform

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 626 bytes --]

On Fri, Apr 24, 2015 at 03:17:50PM -0700, Feng Kan wrote:
> Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
> device driver use the SLIMpro Mailbox driver to tunnel message to
> the SLIMpro coprocessor to do the work of accessing I2C components.
> 
> Signed-off-by: Feng Kan <fkan@apm.com>
> Signed-off-by: Hieu Le <hnle@apm.com>

Applied to for-next, thanks!

One comment though:

> +	adapter->class = I2C_CLASS_HWMON;

Since you have DT and ACPI, you most likely won't need that, or?
It speeds up boot time if you don't use classes. Send me an incremental
patch if you want to change this.


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 2/4] i2c: busses: xgene: add acpi support for i2c xgene SLIMpro driver

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 237 bytes --]

On Fri, Apr 24, 2015 at 03:17:51PM -0700, Feng Kan wrote:
> This adds support for ACPI for the APM X-Gene I2C SLIMpro proxy
> driver.
> 
> Signed-off-by: Feng Kan <fkan@apm.com>

I squashed this into the previous patch, thanks.


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 3/4] Documentation: i2c: Add APM X-Gene platform SLIMpro I2C driver documentation

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 283 bytes --]

On Fri, Apr 24, 2015 at 03:17:52PM -0700, Feng Kan wrote:
> Add APM X-Gene platform SLIMpro I2C driver documentation.
> 
> Signed-off-by: Feng Kan <fkan-qTEPVZfXA3Y@public.gmane.org>
> Signed-off-by: Hieu Le <hnle-qTEPVZfXA3Y@public.gmane.org>

Applied to for-next, thanks!


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 3/4] Documentation: i2c: Add APM X-Gene platform SLIMpro I2C driver documentation

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 241 bytes --]

On Fri, Apr 24, 2015 at 03:17:52PM -0700, Feng Kan wrote:
> Add APM X-Gene platform SLIMpro I2C driver documentation.
> 
> Signed-off-by: Feng Kan <fkan@apm.com>
> Signed-off-by: Hieu Le <hnle@apm.com>

Applied to for-next, thanks!


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH RESEND V4 4/4] arm64: dts: add proxy I2C device driver on APM X-Gene platform

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 252 bytes --]

On Fri, Apr 24, 2015 at 03:17:53PM -0700, Feng Kan wrote:
> Add proxy I2C device driver on APM X-Gene platform.
> 
> Signed-off-by: Feng Kan <fkan@apm.com>
> Signed-off-by: Hieu Le <hnle@apm.com>

DTS updates need to go via arm trees usually.


[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]