From: Bjorn Helgaas <bhelgaas@google.com>
To: Duc Dang <dhdang@apm.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>,
"linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>,
linux-arm <linux-arm-kernel@lists.infradead.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: X-Gene: Unhandled fault: synchronous external abort in pci_generic_config_read32
Date: Tue, 28 Jul 2015 16:29:44 -0500 [thread overview]
Message-ID: <20150728212944.GA12958@google.com> (raw)
In-Reply-To: <CADaLNDn95H=g73DKWRsrB4SuWcf+-8mkepbwb_DC-sFsVkrk6g@mail.gmail.com>
On Tue, Jul 28, 2015 at 10:45:26AM -0700, Duc Dang wrote:
> On Tue, Jul 28, 2015 at 9:43 AM, Bjorn Helgaas <bhelgaas@google.com> wrote:
> > On Fri, Jul 24, 2015 at 7:05 PM, Duc Dang <dhdang@apm.com> wrote:
> >> Hi Bjorn,
> >>
> >> On Fri, Jul 24, 2015 at 3:42 PM, Bjorn Helgaas <bhelgaas@google.com> wrote:
> >>>
> >>> I regularly see faults like this on an APM X-Gene:
> >>>
> >>> U-Boot 2013.04-mustang_sw_1.14.14 (Dec 16 2014 - 15:59:33)
> >>> CPU0: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
> >>> 32 KB ICACHE, 32 KB DCACHE
> >>> SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
> >>> ...
> >>> Unhandled fault: synchronous external abort (0x96000010) at 0xffffff8000110034
> >>> Internal error: : 96000010 [#1] SMP
> >>> Modules linked in:
> >>> CPU: 0 PID: 3723 Comm: ... 4.1.0-smp-DEV #3
> >>> Hardware name: APM X-Gene Mustang board (DT)
> >>> task: ffffffc7dc1a4140 ti: ffffffc7dc118000 task.ti: ffffffc7dc118000
> >>> PC is at pci_generic_config_read32+0x4c/0xb8
> >>> LR is at pci_generic_config_read32+0x40/0xb8
> >>> pc : [<ffffffc00033b90c>] lr : [<ffffffc00033b900>] pstate: 600001c5
> >>> ...
> >>> Call trace:
> >>> [<ffffffc00033b90c>] pci_generic_config_read32+0x4c/0xb8
> >>> [<ffffffc00033bf58>] pci_user_read_config_byte+0x60/0xc4
> >>> [<ffffffc0003496a8>] pci_read_config+0x15c/0x238
> >>> [<ffffffc0002393b4>] sysfs_kf_bin_read+0x68/0xa0
> >>> [<ffffffc00023896c>] kernfs_fop_read+0x9c/0x1ac
> >>> [<ffffffc0001c361c>] __vfs_read+0x44/0x128
> >>> [<ffffffc0001c3e28>] vfs_read+0x84/0x144
> >>> [<ffffffc0001c4764>] SyS_read+0x50/0xb0
> >>
> >> The log shows kernel gets an exception when trying to access Mellanox
> >> card configuration space. This is usually due to suboptimal PCIe
> >> SerDes parameters are using in your board, which will cause bad link
> >> quality.
> >> The PCIe SerDes programming is done in U-Boot, so I suggest you do a
> >> U-Boot upgrade to our latest X-Gene U-Boot release.
> >
> > I installed U-Boot 1.15.12, which I thought was the latest. I'm still
> > seeing this issue regularly, approx once/hour.
>
> Our latest U-Boot is 1.15.15, but U-Boot 1.15.12 is already a good
> version to use. Are you running any PCIe traffic test when the error
> happens?
Nope, the machine was either idle or running a reboot test; no PCIe stress
test or anything.
> And it will be useful if you can share your "lspci -vvv" output when
> the board is running, we can check to see if there is any error status
> reported.
Here's some lspci output and info about the firmware I'm running.
Obviously this lspci output was collected before a crash. I have also
seen lspci output where "CESta: RxErr+" was set on the 00:00.0 Root Port.
U-Boot 2013.04-mustang_sw_1.15.12 (May 20 2015 - 10:03:33)
CPU0: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
32 KB ICACHE, 32 KB DCACHE
SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
Boot from SPI-NOR
Slimpro FW:
Ver: 2.4 (build 01.15.12.00 2015/05/20)
PMD: 970 mV
SOC: 950 mV
Board: Mustang - AppliedMicro APM883208-xNA24SPT Reference Board
I2C: ready
DRAM: ECC 32 GiB @ 1600MHz
SF: Detected N25Q256 with page size 256 Bytes, total 32 MiB
MMC: X-Gene SD/SDIO/eMMC: 0
PCIE0: (RC) X8 GEN-3 link up
00:00.0 - 10e8:e004 - Bridge device
01:00.0 - 15b3:1007 - Network controller
# lspci -vvv
00:00.0 PCI bridge: Applied Micro Circuits Corp. Device e004 (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: 80000000-82ffffff
Prefetchable memory behind bridge: 0000000083000000-00000000830fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr+ UnsuppReq- AuxPwr- TransPend+
LnkCap: Port #0, Speed unknown, Width x8, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: Unknown, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [180 v1] #19
Capabilities: [150 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: pcieport
01:00.0 Ethernet controller: Mellanox Technologies MT27520 Family
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 226
Region 0: [virtual] Memory at e182000000 (32-bit, non-prefetchable) [size=1M]
Region 2: [virtual] Memory at e180000000 (32-bit, non-prefetchable) [size=32M]
[virtual] Expansion ROM at e183000000 [disabled] [size=1M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [9c] MSI-X: Enable- Count=64 Masked-
Vector table: BAR=0 offset=0007c000
PBA: BAR=0 offset=0007d000
Capabilities: [60] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #8, Speed unknown, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: Unknown, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 0
ARICtl: MFVC- ACS-, Function Group: 0
Capabilities: [148 v1] Device Serial Number xx-xx-xx-xx-xx-xx-xx-xx
Capabilities: [154 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [18c v1] #19
Kernel modules: mlx4_core
WARNING: multiple messages have this Message-ID (diff)
From: bhelgaas@google.com (Bjorn Helgaas)
To: linux-arm-kernel@lists.infradead.org
Subject: X-Gene: Unhandled fault: synchronous external abort in pci_generic_config_read32
Date: Tue, 28 Jul 2015 16:29:44 -0500 [thread overview]
Message-ID: <20150728212944.GA12958@google.com> (raw)
In-Reply-To: <CADaLNDn95H=g73DKWRsrB4SuWcf+-8mkepbwb_DC-sFsVkrk6g@mail.gmail.com>
On Tue, Jul 28, 2015 at 10:45:26AM -0700, Duc Dang wrote:
> On Tue, Jul 28, 2015 at 9:43 AM, Bjorn Helgaas <bhelgaas@google.com> wrote:
> > On Fri, Jul 24, 2015 at 7:05 PM, Duc Dang <dhdang@apm.com> wrote:
> >> Hi Bjorn,
> >>
> >> On Fri, Jul 24, 2015 at 3:42 PM, Bjorn Helgaas <bhelgaas@google.com> wrote:
> >>>
> >>> I regularly see faults like this on an APM X-Gene:
> >>>
> >>> U-Boot 2013.04-mustang_sw_1.14.14 (Dec 16 2014 - 15:59:33)
> >>> CPU0: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
> >>> 32 KB ICACHE, 32 KB DCACHE
> >>> SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
> >>> ...
> >>> Unhandled fault: synchronous external abort (0x96000010) at 0xffffff8000110034
> >>> Internal error: : 96000010 [#1] SMP
> >>> Modules linked in:
> >>> CPU: 0 PID: 3723 Comm: ... 4.1.0-smp-DEV #3
> >>> Hardware name: APM X-Gene Mustang board (DT)
> >>> task: ffffffc7dc1a4140 ti: ffffffc7dc118000 task.ti: ffffffc7dc118000
> >>> PC is at pci_generic_config_read32+0x4c/0xb8
> >>> LR is at pci_generic_config_read32+0x40/0xb8
> >>> pc : [<ffffffc00033b90c>] lr : [<ffffffc00033b900>] pstate: 600001c5
> >>> ...
> >>> Call trace:
> >>> [<ffffffc00033b90c>] pci_generic_config_read32+0x4c/0xb8
> >>> [<ffffffc00033bf58>] pci_user_read_config_byte+0x60/0xc4
> >>> [<ffffffc0003496a8>] pci_read_config+0x15c/0x238
> >>> [<ffffffc0002393b4>] sysfs_kf_bin_read+0x68/0xa0
> >>> [<ffffffc00023896c>] kernfs_fop_read+0x9c/0x1ac
> >>> [<ffffffc0001c361c>] __vfs_read+0x44/0x128
> >>> [<ffffffc0001c3e28>] vfs_read+0x84/0x144
> >>> [<ffffffc0001c4764>] SyS_read+0x50/0xb0
> >>
> >> The log shows kernel gets an exception when trying to access Mellanox
> >> card configuration space. This is usually due to suboptimal PCIe
> >> SerDes parameters are using in your board, which will cause bad link
> >> quality.
> >> The PCIe SerDes programming is done in U-Boot, so I suggest you do a
> >> U-Boot upgrade to our latest X-Gene U-Boot release.
> >
> > I installed U-Boot 1.15.12, which I thought was the latest. I'm still
> > seeing this issue regularly, approx once/hour.
>
> Our latest U-Boot is 1.15.15, but U-Boot 1.15.12 is already a good
> version to use. Are you running any PCIe traffic test when the error
> happens?
Nope, the machine was either idle or running a reboot test; no PCIe stress
test or anything.
> And it will be useful if you can share your "lspci -vvv" output when
> the board is running, we can check to see if there is any error status
> reported.
Here's some lspci output and info about the firmware I'm running.
Obviously this lspci output was collected before a crash. I have also
seen lspci output where "CESta: RxErr+" was set on the 00:00.0 Root Port.
U-Boot 2013.04-mustang_sw_1.15.12 (May 20 2015 - 10:03:33)
CPU0: APM ARM 64-bit Potenza Rev B0 2400MHz PCP 2400MHz
32 KB ICACHE, 32 KB DCACHE
SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz
Boot from SPI-NOR
Slimpro FW:
Ver: 2.4 (build 01.15.12.00 2015/05/20)
PMD: 970 mV
SOC: 950 mV
Board: Mustang - AppliedMicro APM883208-xNA24SPT Reference Board
I2C: ready
DRAM: ECC 32 GiB @ 1600MHz
SF: Detected N25Q256 with page size 256 Bytes, total 32 MiB
MMC: X-Gene SD/SDIO/eMMC: 0
PCIE0: (RC) X8 GEN-3 link up
00:00.0 - 10e8:e004 - Bridge device
01:00.0 - 15b3:1007 - Network controller
# lspci -vvv
00:00.0 PCI bridge: Applied Micro Circuits Corp. Device e004 (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: 80000000-82ffffff
Prefetchable memory behind bridge: 0000000083000000-00000000830fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr+ UnsuppReq- AuxPwr- TransPend+
LnkCap: Port #0, Speed unknown, Width x8, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: Unknown, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [180 v1] #19
Capabilities: [150 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: pcieport
01:00.0 Ethernet controller: Mellanox Technologies MT27520 Family
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 226
Region 0: [virtual] Memory at e182000000 (32-bit, non-prefetchable) [size=1M]
Region 2: [virtual] Memory at e180000000 (32-bit, non-prefetchable) [size=32M]
[virtual] Expansion ROM@e183000000 [disabled] [size=1M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [9c] MSI-X: Enable- Count=64 Masked-
Vector table: BAR=0 offset=0007c000
PBA: BAR=0 offset=0007d000
Capabilities: [60] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #8, Speed unknown, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: Unknown, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 0
ARICtl: MFVC- ACS-, Function Group: 0
Capabilities: [148 v1] Device Serial Number xx-xx-xx-xx-xx-xx-xx-xx
Capabilities: [154 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [18c v1] #19
Kernel modules: mlx4_core
next prev parent reply other threads:[~2015-07-28 21:29 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-24 22:42 X-Gene: Unhandled fault: synchronous external abort in pci_generic_config_read32 Bjorn Helgaas
2015-07-24 22:42 ` Bjorn Helgaas
2015-07-25 0:05 ` Duc Dang
2015-07-25 0:05 ` Duc Dang
2015-07-27 11:36 ` Catalin Marinas
2015-07-27 11:36 ` Catalin Marinas
2015-07-28 17:39 ` Duc Dang
2015-07-28 17:39 ` Duc Dang
2015-07-28 18:36 ` Bjorn Helgaas
2015-07-28 18:36 ` Bjorn Helgaas
2015-07-28 16:43 ` Bjorn Helgaas
2015-07-28 16:43 ` Bjorn Helgaas
2015-07-28 17:45 ` Duc Dang
2015-07-28 17:45 ` Duc Dang
2015-07-28 21:29 ` Bjorn Helgaas [this message]
2015-07-28 21:29 ` Bjorn Helgaas
2015-07-28 21:50 ` Duc Dang
2015-07-28 21:50 ` Duc Dang
2015-07-29 1:22 ` Bjorn Helgaas
2015-07-29 1:22 ` Bjorn Helgaas
2015-07-29 15:55 ` Bjorn Helgaas
2015-07-29 15:55 ` Bjorn Helgaas
2015-07-31 17:00 ` Duc Dang
2015-07-31 17:00 ` Duc Dang
2015-08-10 16:18 ` Bjorn Helgaas
2015-08-10 16:18 ` Bjorn Helgaas
2015-08-10 17:38 ` Catalin Marinas
2015-08-10 17:38 ` Catalin Marinas
[not found] ` <CADaLNDkUQHzGACfFmYDeJWnaNrKmJUDx4Rby60OWr4FzOjx3rA@mail.gmail.com>
2015-08-10 17:42 ` Bjorn Helgaas
2015-08-10 17:42 ` Bjorn Helgaas
2015-08-10 19:07 ` Duc Dang
2015-08-10 19:07 ` Duc Dang
2015-08-11 19:28 ` Bjorn Helgaas
2015-08-11 19:28 ` Bjorn Helgaas
2015-09-05 20:13 ` Jon Masters
2015-09-05 20:13 ` Jon Masters
2015-09-05 20:22 ` Jon Masters
2015-09-05 20:22 ` Jon Masters
2016-04-13 9:58 ` Sudeep Holla
2016-04-13 9:58 ` Sudeep Holla
2016-04-13 13:21 ` Bjorn Helgaas
2016-04-13 13:21 ` Bjorn Helgaas
2016-04-13 13:29 ` Sudeep Holla
2016-04-13 13:29 ` Sudeep Holla
2016-04-13 22:17 ` Jon Masters
2016-04-13 22:17 ` Jon Masters
2015-07-28 14:37 ` Dall, Elizabeth J
2015-07-28 14:37 ` Dall, Elizabeth J
2015-07-28 14:37 ` Dall, Elizabeth J
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150728212944.GA12958@google.com \
--to=bhelgaas@google.com \
--cc=dhdang@apm.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=tinamdar@apm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.