* [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator
@ 2015-07-28 14:48 Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition Peng Fan
` (4 more replies)
0 siblings, 5 replies; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
This patch set is to support driver model for pfuze100 and implement
regulator driver for pfuze100. Patches has been tested on i.MX7D
validation board.
Here registeres for standby mode are not touched, all operation read/write
register are for NORMAL state. For example, to pfuze100,
sw1volt is for controlling voltage for normal state, sw1stdby is for
controlling voltage for standby state. The driver only read/write sw1volt,
but not touch sw1stdby. This will be done later, since I do not come up
with a good idea to operate sw1stdby.
This pfuze driver model part and regulator driver use max77686 driver
as a reference.
Peng Fan (5):
power: pfuze100 correct SWBST macro definition
power: regulator use node name when no regulator-name
power: pmic: pfuze100 support driver model
power: regulator: add pfuze100 support
fsl: common: pfuze: no use original pfuze code if DM_PMIC
board/freescale/common/pfuze.c | 2 +
drivers/power/pmic/Kconfig | 7 +
drivers/power/pmic/pmic_pfuze100.c | 89 +++++
drivers/power/regulator/Kconfig | 8 +
drivers/power/regulator/Makefile | 1 +
drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++
drivers/power/regulator/regulator-uclass.c | 4 +-
include/power/pfuze100_pmic.h | 29 +-
8 files changed, 730 insertions(+), 6 deletions(-)
create mode 100644 drivers/power/regulator/pfuze100.c
--
1.8.4
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
@ 2015-07-28 14:48 ` Peng Fan
2015-08-02 22:30 ` Simon Glass
2015-07-28 14:48 ` [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name Peng Fan
` (3 subsequent siblings)
4 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
According to datasheet, SWBST_MODE starts from bit 2 and it occupies 2 bits.
So SWBST_MODE_MASK should be 0xC, and SWBST_MODE_xx should be ([mode] << 2).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
---
include/power/pfuze100_pmic.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
index 57b9ca9..cb10605 100644
--- a/include/power/pfuze100_pmic.h
+++ b/include/power/pfuze100_pmic.h
@@ -193,11 +193,11 @@ enum {
#define SWBST_5_15V 3
#define SWBST_VOL_MASK 0x3
-#define SWBST_MODE_MASK 0x6
-#define SWBST_MODE_OFF (2 << 0)
-#define SWBST_MODE_PFM (2 << 1)
+#define SWBST_MODE_MASK 0xC
+#define SWBST_MODE_OFF (0 << 2)
+#define SWBST_MODE_PFM (1 << 2)
#define SWBST_MODE_AUTO (2 << 2)
-#define SWBST_MODE_APS (2 << 3)
+#define SWBST_MODE_APS (3 << 2)
/*
* Regulator Mode Control
--
1.8.4
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition Peng Fan
@ 2015-07-28 14:48 ` Peng Fan
2015-08-02 22:31 ` Simon Glass
2015-07-28 14:48 ` [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model Peng Fan
` (2 subsequent siblings)
4 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
---
drivers/power/regulator/regulator-uclass.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/power/regulator/regulator-uclass.c b/drivers/power/regulator/regulator-uclass.c
index 12e141b..d4f06d5 100644
--- a/drivers/power/regulator/regulator-uclass.c
+++ b/drivers/power/regulator/regulator-uclass.c
@@ -256,7 +256,9 @@ static int regulator_post_bind(struct udevice *dev)
if (!uc_pdata->name) {
debug("%s: dev: %s has no property 'regulator-name'\n",
__func__, dev->name);
- return -EINVAL;
+ uc_pdata->name = fdt_get_name(blob, offset, NULL);
+ if (!uc_pdata->name)
+ return -EINVAL;
}
if (regulator_name_is_unique(dev, uc_pdata->name))
--
1.8.4
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name Peng Fan
@ 2015-07-28 14:48 ` Peng Fan
2015-08-02 22:31 ` Simon Glass
2015-08-03 15:01 ` Przemyslaw Marczak
2015-07-28 14:48 ` [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC Peng Fan
4 siblings, 2 replies; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
---
drivers/power/pmic/Kconfig | 7 +++
drivers/power/pmic/pmic_pfuze100.c | 89 ++++++++++++++++++++++++++++++++++++++
include/power/pfuze100_pmic.h | 3 ++
3 files changed, 99 insertions(+)
diff --git a/drivers/power/pmic/Kconfig b/drivers/power/pmic/Kconfig
index 164f421..0df91be 100644
--- a/drivers/power/pmic/Kconfig
+++ b/drivers/power/pmic/Kconfig
@@ -10,6 +10,13 @@ config DM_PMIC
- 'drivers/power/pmic/pmic-uclass.c'
- 'include/power/pmic.h'
+config DM_PMIC_PFUZE100
+ bool "Enable Driver Model for PMIC PFUZE100"
+ depends on DM_PMIC
+ ---help---
+ This config enables implementation of driver-model pmic uclass features
+ for PMIC PFUZE100. The driver implements read/write operations.
+
config DM_PMIC_MAX77686
bool "Enable Driver Model for PMIC MAX77686"
depends on DM_PMIC
diff --git a/drivers/power/pmic/pmic_pfuze100.c b/drivers/power/pmic/pmic_pfuze100.c
index 22a04c0..be9d05c 100644
--- a/drivers/power/pmic/pmic_pfuze100.c
+++ b/drivers/power/pmic/pmic_pfuze100.c
@@ -2,15 +2,22 @@
* Copyright (C) 2014 Gateworks Corporation
* Tim Harvey <tharvey@gateworks.com>
*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc
+ * Peng Fan <Peng.Fan@freescale.com>
+ *
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
+#include <fdtdec.h>
#include <errno.h>
+#include <dm.h>
#include <i2c.h>
#include <power/pmic.h>
+#include <power/regulator.h>
#include <power/pfuze100_pmic.h>
+#ifndef CONFIG_DM_PMIC
int power_pfuze100_init(unsigned char bus)
{
static const char name[] = "PFUZE100";
@@ -30,3 +37,85 @@ int power_pfuze100_init(unsigned char bus)
return 0;
}
+#else
+DECLARE_GLOBAL_DATA_PTR;
+
+static const struct pmic_child_info pmic_children_info[] = {
+ /* sw[x], swbst */
+ { .prefix = "s", .driver = "pfuze100_regulator" },
+ /* vgen[x], vsnvs, vcc, v33, vcc_sd */
+ { .prefix = "v", .driver = "pfuze100_regulator" },
+ { },
+};
+
+static int pfuze100_reg_count(struct udevice *dev)
+{
+ return PMIC_NUM_OF_REGS;
+}
+
+static int pfuze100_write(struct udevice *dev, uint reg, const uint8_t *buff,
+ int len)
+{
+ if (dm_i2c_write(dev, reg, buff, len)) {
+ error("write error to device: %p register: %#x!", dev, reg);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int pfuze100_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
+{
+ if (dm_i2c_read(dev, reg, buff, len)) {
+ error("read error from device: %p register: %#x!", dev, reg);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int pfuze100_bind(struct udevice *dev)
+{
+ int regulators_node;
+ const void *blob = gd->fdt_blob;
+ int children;
+
+ regulators_node = fdt_subnode_offset(blob, dev->of_offset,
+ "regulators");
+ if (regulators_node <= 0) {
+ debug("%s: %s regulators subnode not found!", __func__,
+ dev->name);
+ return -ENXIO;
+ }
+
+ debug("%s: '%s' - found regulators subnode\n", __func__, dev->name);
+
+ children = pmic_bind_children(dev, regulators_node, pmic_children_info);
+ if (!children)
+ debug("%s: %s - no child found\n", __func__, dev->name);
+
+ /* Always return success for this device */
+ return 0;
+}
+
+static struct dm_pmic_ops pfuze100_ops = {
+ .reg_count = pfuze100_reg_count,
+ .read = pfuze100_read,
+ .write = pfuze100_write,
+};
+
+static const struct udevice_id pfuze100_ids[] = {
+ { .compatible = "fsl,pfuze100", .data = (long)PFUZE100, },
+ { .compatible = "fsl,pfuze200", .data = (long)PFUZE200, },
+ { .compatible = "fsl,pfuze3000", .data = (long)PFUZE3000, },
+ { }
+};
+
+U_BOOT_DRIVER(pmic_pfuze100) = {
+ .name = "pfuze100 pmic",
+ .id = UCLASS_PMIC,
+ .of_match = pfuze100_ids,
+ .bind = pfuze100_bind,
+ .ops = &pfuze100_ops,
+};
+#endif
diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
index cb10605..b13a780 100644
--- a/include/power/pfuze100_pmic.h
+++ b/include/power/pfuze100_pmic.h
@@ -8,6 +8,9 @@
#ifndef __PFUZE100_PMIC_H_
#define __PFUZE100_PMIC_H_
+/* Device ID */
+enum {PFUZE100 = 0x10, PFUZE200 = 0x11, PFUZE3000 = 0x30};
+
/* PFUZE100 registers */
enum {
PFUZE100_DEVICEID = 0x00,
--
1.8.4
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
` (2 preceding siblings ...)
2015-07-28 14:48 ` [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model Peng Fan
@ 2015-07-28 14:48 ` Peng Fan
2015-08-02 22:30 ` Simon Glass
2015-07-28 14:48 ` [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC Peng Fan
4 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for mataining info for regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
---
drivers/power/regulator/Kconfig | 8 +
drivers/power/regulator/Makefile | 1 +
drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
include/power/pfuze100_pmic.h | 24 +-
4 files changed, 625 insertions(+), 4 deletions(-)
create mode 100644 drivers/power/regulator/pfuze100.c
diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
index 6289b83..b854773 100644
--- a/drivers/power/regulator/Kconfig
+++ b/drivers/power/regulator/Kconfig
@@ -16,6 +16,14 @@ config DM_REGULATOR
for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
otherwise. Detailed information can be found in the header file.
+config DM_REGULATOR_PFUZE100
+ bool "Enable Driver Model for REGULATOR PFUZE100"
+ depends on DM_REGULATOR && DM_PMIC_PFUZE100
+ ---help---
+ This config enables implementation of driver-model regulator uclass
+ features for REGULATOR PFUZE100. The driver implements get/set api for:
+ value, enable and mode.
+
config DM_REGULATOR_MAX77686
bool "Enable Driver Model for REGULATOR MAX77686"
depends on DM_REGULATOR && DM_PMIC_MAX77686
diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
index 96aa624..9f8f17b 100644
--- a/drivers/power/regulator/Makefile
+++ b/drivers/power/regulator/Makefile
@@ -7,5 +7,6 @@
obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
+obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
new file mode 100644
index 0000000..6c513e9
--- /dev/null
+++ b/drivers/power/regulator/pfuze100.c
@@ -0,0 +1,596 @@
+#include <common.h>
+#include <fdtdec.h>
+#include <errno.h>
+#include <dm.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <power/regulator.h>
+#include <power/pfuze100_pmic.h>
+
+/**
+ * struct pfuze100_regulator_desc - regulator descriptor
+ *
+ * @name: Identify name for the regulator.
+ * @type: Indicates the regulator type.
+ * @uV_step: Voltage increase for each selector.
+ * @vsel_reg: Register for adjust regulator voltage for normal.
+ * @vsel_mask: Mask bit for setting regulator voltage for normal.
+ * @stby_reg: Register for adjust regulator voltage for standby.
+ * @stby_mask: Mask bit for setting regulator voltage for standby.
+ * @volt_table: Voltage mapping table (if table based mapping).
+ * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
+ */
+struct pfuze100_regulator_desc {
+ char *name;
+ enum regulator_type type;
+ unsigned int uV_step;
+ unsigned int vsel_reg;
+ unsigned int vsel_mask;
+ unsigned int stby_reg;
+ unsigned int stby_mask;
+ unsigned int *volt_table;
+ unsigned int voltage;
+};
+
+#define PFUZE100_FIXED_REG(_name, base, vol) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_FIXED, \
+ .voltage = (vol), \
+ }
+
+#define PFUZE100_SW_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_BUCK, \
+ .uV_step = (step), \
+ .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
+ .vsel_mask = 0x3F, \
+ .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
+ .stby_mask = 0x3F, \
+ }
+
+#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_BUCK, \
+ .uV_step = (step), \
+ .vsel_reg = (base), \
+ .vsel_mask = (mask), \
+ .volt_table = (voltages), \
+ }
+
+#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_OTHER, \
+ .vsel_reg = (base), \
+ .vsel_mask = (mask), \
+ .volt_table = (voltages), \
+ }
+
+#define PFUZE100_VGEN_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_LDO, \
+ .uV_step = (step), \
+ .vsel_reg = (base), \
+ .vsel_mask = 0xF, \
+ .stby_reg = (base), \
+ .stby_mask = 0x20, \
+ }
+
+#define PFUZE3000_VCC_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_LDO, \
+ .uV_step = (step), \
+ .vsel_reg = (base), \
+ .vsel_mask = 0x3, \
+ .stby_reg = (base), \
+ .stby_mask = 0x20, \
+}
+
+#define PFUZE3000_SW1_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_BUCK, \
+ .uV_step = (step), \
+ .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
+ .vsel_mask = 0x1F, \
+ .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
+ .stby_mask = 0x1F, \
+ }
+
+#define PFUZE3000_SW2_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_BUCK, \
+ .uV_step = (step), \
+ .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
+ .vsel_mask = 0x7, \
+ .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
+ .stby_mask = 0x7, \
+ }
+
+#define PFUZE3000_SW3_REG(_name, base, step) \
+ { \
+ .name = #_name, \
+ .type = REGULATOR_TYPE_BUCK, \
+ .uV_step = (step), \
+ .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
+ .vsel_mask = 0xF, \
+ .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
+ .stby_mask = 0xF, \
+ }
+
+static unsigned int pfuze100_swbst[] = {
+ 5000000, 5050000, 5100000, 5150000
+};
+
+static unsigned int pfuze100_vsnvs[] = {
+ 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
+};
+
+static unsigned int pfuze3000_vsnvs[] = {
+ -1, -1, -1, -1, -1, -1, 3000000, -1
+};
+
+static unsigned int pfuze3000_sw2lo[] = {
+ 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
+};
+
+/* PFUZE100 */
+static struct pfuze100_regulator_desc pfuze100_regulators[] = {
+ PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
+ PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
+ PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
+ PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
+ PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
+ PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
+ PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
+ PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
+ PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
+ PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
+ PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
+ PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
+ PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
+ PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
+ PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
+};
+
+/* PFUZE200 */
+static struct pfuze100_regulator_desc pfuze200_regulators[] = {
+ PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
+ PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
+ PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
+ PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
+ PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
+ PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
+ PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
+ PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
+ PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
+ PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
+ PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
+ PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
+ PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
+};
+
+/* PFUZE3000 */
+static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
+ PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
+ PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
+ PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
+ PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
+ PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
+ PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
+ PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
+ PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
+ PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
+ PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
+ PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
+ PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
+ PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
+};
+
+#define MODE(_id, _val, _name) { \
+ .id = _id, \
+ .register_value = _val, \
+ .name = _name, \
+}
+
+/* SWx Buck regulator mode */
+static struct dm_regulator_mode pfuze_sw_modes[] = {
+ MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
+ MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
+ MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
+ MODE(APS_OFF, APS_OFF, "APS_OFF"),
+ MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
+ MODE(PWM_APS, PWM_APS, "PWM_APS"),
+ MODE(APS_APS, APS_APS, "APS_APS"),
+ MODE(APS_PFM, APS_PFM, "APS_PFM"),
+ MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
+};
+
+/* Boost Buck regulator mode for normal operation */
+static struct dm_regulator_mode pfuze_swbst_modes[] = {
+ MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
+ MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
+ MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
+ MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
+};
+
+/* VGENx LDO regulator mode for normal operation */
+static struct dm_regulator_mode pfuze_ldo_modes[] = {
+ MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
+ MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
+};
+
+static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
+ int size,
+ const char *name)
+{
+ int i;
+ for (i = 0; i < size; desc++) {
+ if (!strcmp(desc->name, name))
+ return desc;
+ continue;
+ }
+
+ return NULL;
+}
+
+static int pfuze100_regulator_probe(struct udevice *dev)
+{
+ struct dm_regulator_uclass_platdata *uc_pdata;
+ struct pfuze100_regulator_desc **desc = NULL;
+
+ desc = dev_get_platdata(dev);
+
+ switch (dev_get_driver_data(dev_get_parent(dev))) {
+ case PFUZE100:
+ *desc = se_desc(pfuze100_regulators,
+ ARRAY_SIZE(pfuze100_regulators),
+ dev->name);
+ break;
+ case PFUZE200:
+ *desc = se_desc(pfuze200_regulators,
+ ARRAY_SIZE(pfuze200_regulators),
+ dev->name);
+ break;
+ case PFUZE3000:
+ *desc = se_desc(pfuze3000_regulators,
+ ARRAY_SIZE(pfuze3000_regulators),
+ dev->name);
+ break;
+ }
+ if (!*desc) {
+ debug("Do not support regulator %s\n", dev->name);
+ return -EINVAL;
+ }
+
+ uc_pdata = dev_get_uclass_platdata(dev);
+
+ uc_pdata->type = (*desc)->type;
+ if (uc_pdata->type == REGULATOR_TYPE_BUCK) {
+ if (!strcmp(dev->name, "swbst")) {
+ uc_pdata->mode = pfuze_swbst_modes;
+ uc_pdata->mode_count = ARRAY_SIZE(pfuze_swbst_modes);
+ } else {
+ uc_pdata->mode = pfuze_sw_modes;
+ uc_pdata->mode_count = ARRAY_SIZE(pfuze_sw_modes);
+ }
+ } else if (uc_pdata->type == REGULATOR_TYPE_LDO) {
+ uc_pdata->mode = pfuze_ldo_modes;
+ uc_pdata->mode_count = ARRAY_SIZE(pfuze_ldo_modes);
+ } else {
+ uc_pdata->mode = NULL;
+ uc_pdata->mode_count = 0;
+ }
+
+ return 0;
+}
+
+static int pfuze100_regulator_mode(struct udevice *dev, int op, int *opmode)
+{
+ unsigned char val;
+ int ret;
+ struct pfuze100_regulator_desc *desc =
+ *(struct pfuze100_regulator_desc **)dev_get_platdata(dev);
+
+ if (op == PMIC_OP_GET) {
+ if (desc->type == REGULATOR_TYPE_BUCK) {
+ if (!strcmp(dev->name, "swbst")) {
+ ret = pmic_read(dev->parent, desc->vsel_reg,
+ &val, 1);
+ if (ret)
+ return ret;
+
+ val &= SWBST_MODE_MASK;
+ val >>= SWBST_MODE_SHIFT;
+ *opmode = val;
+
+ return 0;
+ }
+ ret = pmic_read(dev->parent,
+ desc->vsel_reg + PFUZE100_MODE_OFFSET,
+ &val, 1);
+ if (ret)
+ return ret;
+
+ val &= SW_MODE_MASK;
+ val >>= SW_MODE_SHIFT;
+ *opmode = val;
+
+ return 0;
+
+ } else if (desc->type == REGULATOR_TYPE_LDO) {
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ val &= LDO_MODE_MASK;
+ val >>= LDO_MODE_SHIFT;
+ *opmode = val;
+
+ return 0;
+ } else {
+ return -EINVAL;
+ }
+ }
+
+ if (desc->type == REGULATOR_TYPE_BUCK) {
+ if (!strcmp(dev->name, "swbst")) {
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ val &= ~SWBST_MODE_MASK;
+ val |= *opmode << SWBST_MODE_SHIFT;
+
+ ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ return 0;
+ }
+ ret = pmic_read(dev->parent,
+ desc->vsel_reg + PFUZE100_MODE_OFFSET,
+ &val, 1);
+ if (ret)
+ return ret;
+
+ val &= ~SW_MODE_MASK;
+ val |= *opmode << SW_MODE_SHIFT;
+
+ ret = pmic_write(dev->parent,
+ desc->vsel_reg + PFUZE100_MODE_OFFSET,
+ &val, 1);
+ if (ret)
+ return ret;
+
+ return 0;
+ } else if (desc->type == REGULATOR_TYPE_LDO) {
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ val &= ~LDO_MODE_MASK;
+ val |= *opmode << LDO_MODE_SHIFT;
+
+ ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ return 0;
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int pfuze100_regulator_enable(struct udevice *dev, int op, bool *enable)
+{
+ int ret, on_off;
+ unsigned char val;
+ struct dm_regulator_uclass_platdata *uc_pdata =
+ dev_get_uclass_platdata(dev);
+ if (op == PMIC_OP_GET) {
+ if (!strcmp(dev->name, "vrefddr")) {
+ ret = pmic_read(dev->parent, PFUZE100_VREFDDRCON,
+ &val, 1);
+ if (ret)
+ return ret;
+ if (val & VREFDDRCON_EN)
+ *enable = true;
+ else
+ *enable = false;
+ return 0;
+ }
+ ret = pfuze100_regulator_mode(dev, op, &on_off);
+ if (ret)
+ return ret;
+ switch (on_off) {
+ /* OFF_OFF, SWBST_MODE_OFF, LDO_MODE_OFF have same value */
+ case OFF_OFF:
+ *enable = false;
+ break;
+ default:
+ *enable = true;
+ break;
+ }
+ } else if (op == PMIC_OP_SET) {
+ if (!strcmp(dev->name, "vrefddr")) {
+ ret = pmic_read(dev->parent, PFUZE100_VREFDDRCON,
+ &val, 1);
+ if (ret)
+ return ret;
+
+ if (val & VREFDDRCON_EN)
+ return 0;
+ val |= VREFDDRCON_EN;
+
+ return pmic_write(dev->parent, PFUZE100_VREFDDRCON,
+ &val, 1);
+ }
+
+ if (uc_pdata->type == REGULATOR_TYPE_LDO) {
+ on_off = *enable ? LDO_MODE_ON : LDO_MODE_OFF;
+ } else if (uc_pdata->type == REGULATOR_TYPE_BUCK) {
+ if (!strcmp(dev->name, "swbst"))
+ on_off = *enable ? SWBST_MODE_AUTO :
+ SWBST_MODE_OFF;
+ else
+ on_off = *enable ? APS_PFM : OFF_OFF;
+ } else {
+ return -EINVAL;
+ }
+
+ return pfuze100_regulator_mode(dev, op, &on_off);
+ }
+
+ return 0;
+}
+
+static int pfuze100_regulator_val(struct udevice *dev, int op, int *uV)
+{
+ unsigned char val;
+ int i, ret;
+ struct pfuze100_regulator_desc *desc =
+ *(struct pfuze100_regulator_desc **)dev_get_platdata(dev);
+ struct dm_regulator_uclass_platdata *uc_pdata =
+ dev_get_uclass_platdata(dev);
+
+ if (op == PMIC_OP_GET) {
+ *uV = 0;
+ if (uc_pdata->type == REGULATOR_TYPE_FIXED) {
+ *uV = desc->voltage;
+ } else if (desc->volt_table) {
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+ val &= desc->vsel_mask;
+ *uV = desc->volt_table[val];
+ } else {
+ if (uc_pdata->min_uV < 0) {
+ debug("Need to provide min_uV in dts.\n");
+ return -EINVAL;
+ }
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+ val &= desc->vsel_mask;
+ *uV = uc_pdata->min_uV + (int)val * desc->uV_step;
+ }
+
+ return 0;
+ }
+
+ if (uc_pdata->type == REGULATOR_TYPE_FIXED) {
+ debug("Set voltage for REGULATOR_TYPE_FIXED regulator\n");
+ return -EINVAL;
+ } else if (desc->volt_table) {
+ for (i = 0; i < desc->vsel_mask; i++) {
+ if (*uV == desc->volt_table[i])
+ break;
+ }
+ if (i == desc->vsel_mask) {
+ debug("Unsupported voltage %u\n", *uV);
+ return -EINVAL;
+ }
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+ val &= ~(desc->vsel_mask);
+ val |= i;
+ ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+ } else {
+ if (uc_pdata->min_uV < 0) {
+ debug("Need to provide min_uV in dts.\n");
+ return -EINVAL;
+ }
+ ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+
+ val &= ~(desc->vsel_mask);
+ val |= (*uV - uc_pdata->min_uV) / desc->uV_step;
+
+ ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int pfuze100_regulator_get_value(struct udevice *dev)
+{
+ int uV;
+ int ret;
+
+ ret = pfuze100_regulator_val(dev, PMIC_OP_GET, &uV);
+ if (ret)
+ return ret;
+
+ return uV;
+}
+
+static int pfuze100_regulator_set_value(struct udevice *dev, int uV)
+{
+ return pfuze100_regulator_val(dev, PMIC_OP_SET, &uV);
+}
+
+static bool pfuze100_regulator_get_enable(struct udevice *dev)
+{
+ bool enable = false;
+ int ret;
+
+ ret = pfuze100_regulator_enable(dev, PMIC_OP_GET, &enable);
+ if (ret)
+ return ret;
+
+ return enable;
+}
+
+static int pfuze100_regulator_set_enable(struct udevice *dev, bool enable)
+{
+ return pfuze100_regulator_enable(dev, PMIC_OP_SET, &enable);
+}
+
+static int pfuze100_regulator_get_mode(struct udevice *dev)
+{
+ int mode;
+ int ret;
+
+ ret = pfuze100_regulator_mode(dev, PMIC_OP_GET, &mode);
+ if (ret)
+ return ret;
+
+ return mode;
+}
+
+static int pfuze100_regulator_set_mode(struct udevice *dev, int mode)
+{
+ return pfuze100_regulator_mode(dev, PMIC_OP_SET, &mode);
+}
+
+static const struct dm_regulator_ops pfuze100_regulator_ops = {
+ .get_value = pfuze100_regulator_get_value,
+ .set_value = pfuze100_regulator_set_value,
+ .get_enable = pfuze100_regulator_get_enable,
+ .set_enable = pfuze100_regulator_set_enable,
+ .get_mode = pfuze100_regulator_get_mode,
+ .set_mode = pfuze100_regulator_set_mode,
+};
+
+U_BOOT_DRIVER(pfuze100_regulator) = {
+ .name = "pfuze100_regulator",
+ .id = UCLASS_REGULATOR,
+ .ops = &pfuze100_regulator_ops,
+ .probe = pfuze100_regulator_probe,
+ .platdata_auto_alloc_size = sizeof(struct pfuze100_regulator_desc **),
+};
diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
index b13a780..36cc212 100644
--- a/include/power/pfuze100_pmic.h
+++ b/include/power/pfuze100_pmic.h
@@ -60,6 +60,13 @@ enum {
PMIC_NUM_OF_REGS = 0x7f,
};
+/* Registor offset based on VOLT register */
+#define PFUZE100_VOL_OFFSET 0
+#define PFUZE100_STBY_OFFSET 1
+#define PFUZE100_OFF_OFFSET 2
+#define PFUZE100_MODE_OFFSET 3
+#define PFUZE100_CONF_OFFSET 4
+
/*
* Buck Regulators
*/
@@ -136,6 +143,9 @@ enum {
#define SW1x_STBY_MASK 0x3f
#define SW1x_OFF_MASK 0x3f
+#define SW_MODE_MASK 0xf
+#define SW_MODE_SHIFT 0
+
#define SW1xCONF_DVSSPEED_MASK 0xc0
#define SW1xCONF_DVSSPEED_2US 0x00
#define SW1xCONF_DVSSPEED_4US 0x40
@@ -184,7 +194,12 @@ enum {
#define LDO_VOL_MASK 0xf
#define LDO_EN (1 << 4)
+#define LDO_MODE_SHIFT 4
+#define LDO_MODE_MASK (1 << 4)
+#define LDO_MODE_OFF 0
+#define LDO_MODE_ON 1
+#define VREFDDRCON_EN (1 << 4)
/*
* Boost Regulator
*/
@@ -197,10 +212,11 @@ enum {
#define SWBST_VOL_MASK 0x3
#define SWBST_MODE_MASK 0xC
-#define SWBST_MODE_OFF (0 << 2)
-#define SWBST_MODE_PFM (1 << 2)
-#define SWBST_MODE_AUTO (2 << 2)
-#define SWBST_MODE_APS (3 << 2)
+#define SWBST_MODE_SHIFT 0x2
+#define SWBST_MODE_OFF 0
+#define SWBST_MODE_PFM 1
+#define SWBST_MODE_AUTO 2
+#define SWBST_MODE_APS 3
/*
* Regulator Mode Control
--
1.8.4
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
` (3 preceding siblings ...)
2015-07-28 14:48 ` [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support Peng Fan
@ 2015-07-28 14:48 ` Peng Fan
2015-08-02 22:30 ` Simon Glass
4 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-07-28 14:48 UTC (permalink / raw)
To: u-boot
If enable DM PMIC and REGULATOR, we should not use original power
framework. So need to comment out the pfuze code for original power
framework, when CONFIG_DM_PMIC_PFUZE100 defined.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
---
board/freescale/common/pfuze.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c
index d6a209e..783c46d 100644
--- a/board/freescale/common/pfuze.c
+++ b/board/freescale/common/pfuze.c
@@ -9,6 +9,7 @@
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
+#ifndef CONFIG_DM_PMIC_PFUZE100
int pfuze_mode_init(struct pmic *p, u32 mode)
{
unsigned char offset, i, switch_num;
@@ -90,3 +91,4 @@ struct pmic *pfuze_common_init(unsigned char i2cbus)
return p;
}
+#endif
--
1.8.4
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition
2015-07-28 14:48 ` [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition Peng Fan
@ 2015-08-02 22:30 ` Simon Glass
0 siblings, 0 replies; 21+ messages in thread
From: Simon Glass @ 2015-08-02 22:30 UTC (permalink / raw)
To: u-boot
On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
> According to datasheet, SWBST_MODE starts from bit 2 and it occupies 2 bits.
> So SWBST_MODE_MASK should be 0xC, and SWBST_MODE_xx should be ([mode] << 2).
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
> include/power/pfuze100_pmic.h | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-07-28 14:48 ` [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support Peng Fan
@ 2015-08-02 22:30 ` Simon Glass
2015-08-03 0:38 ` Peng Fan
0 siblings, 1 reply; 21+ messages in thread
From: Simon Glass @ 2015-08-02 22:30 UTC (permalink / raw)
To: u-boot
Hi Peng,
On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
> 1. Add new regulator driver pfuze100.
> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
> 3. This driver intends to support PF100, PF200 and PF3000.
> 4. Add related macro definition in pfuze header file.
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Simon Glass <sjg@chromium.org>
It looks correct but I have code style comments - see below. They all
apply globally.
> ---
> drivers/power/regulator/Kconfig | 8 +
> drivers/power/regulator/Makefile | 1 +
> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
> include/power/pfuze100_pmic.h | 24 +-
> 4 files changed, 625 insertions(+), 4 deletions(-)
> create mode 100644 drivers/power/regulator/pfuze100.c
>
> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
> index 6289b83..b854773 100644
> --- a/drivers/power/regulator/Kconfig
> +++ b/drivers/power/regulator/Kconfig
> @@ -16,6 +16,14 @@ config DM_REGULATOR
> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
> otherwise. Detailed information can be found in the header file.
>
> +config DM_REGULATOR_PFUZE100
> + bool "Enable Driver Model for REGULATOR PFUZE100"
> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
> + ---help---
> + This config enables implementation of driver-model regulator uclass
> + features for REGULATOR PFUZE100. The driver implements get/set api for:
> + value, enable and mode.
> +
> config DM_REGULATOR_MAX77686
> bool "Enable Driver Model for REGULATOR MAX77686"
> depends on DM_REGULATOR && DM_PMIC_MAX77686
> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
> index 96aa624..9f8f17b 100644
> --- a/drivers/power/regulator/Makefile
> +++ b/drivers/power/regulator/Makefile
> @@ -7,5 +7,6 @@
>
> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
> new file mode 100644
> index 0000000..6c513e9
> --- /dev/null
> +++ b/drivers/power/regulator/pfuze100.c
> @@ -0,0 +1,596 @@
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <errno.h>
> +#include <dm.h>
> +#include <i2c.h>
> +#include <power/pmic.h>
> +#include <power/regulator.h>
> +#include <power/pfuze100_pmic.h>
> +
> +/**
> + * struct pfuze100_regulator_desc - regulator descriptor
> + *
> + * @name: Identify name for the regulator.
> + * @type: Indicates the regulator type.
> + * @uV_step: Voltage increase for each selector.
> + * @vsel_reg: Register for adjust regulator voltage for normal.
> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
> + * @stby_reg: Register for adjust regulator voltage for standby.
> + * @stby_mask: Mask bit for setting regulator voltage for standby.
> + * @volt_table: Voltage mapping table (if table based mapping).
> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
> + */
> +struct pfuze100_regulator_desc {
> + char *name;
> + enum regulator_type type;
> + unsigned int uV_step;
> + unsigned int vsel_reg;
> + unsigned int vsel_mask;
> + unsigned int stby_reg;
> + unsigned int stby_mask;
> + unsigned int *volt_table;
> + unsigned int voltage;
> +};
> +
> +#define PFUZE100_FIXED_REG(_name, base, vol) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_FIXED, \
> + .voltage = (vol), \
> + }
> +
> +#define PFUZE100_SW_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_BUCK, \
> + .uV_step = (step), \
> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
> + .vsel_mask = 0x3F, \
> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
> + .stby_mask = 0x3F, \
> + }
> +
> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_BUCK, \
> + .uV_step = (step), \
> + .vsel_reg = (base), \
> + .vsel_mask = (mask), \
> + .volt_table = (voltages), \
> + }
> +
> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_OTHER, \
> + .vsel_reg = (base), \
> + .vsel_mask = (mask), \
> + .volt_table = (voltages), \
> + }
> +
> +#define PFUZE100_VGEN_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_LDO, \
> + .uV_step = (step), \
> + .vsel_reg = (base), \
> + .vsel_mask = 0xF, \
> + .stby_reg = (base), \
> + .stby_mask = 0x20, \
> + }
> +
> +#define PFUZE3000_VCC_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_LDO, \
> + .uV_step = (step), \
> + .vsel_reg = (base), \
> + .vsel_mask = 0x3, \
> + .stby_reg = (base), \
> + .stby_mask = 0x20, \
> +}
> +
> +#define PFUZE3000_SW1_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_BUCK, \
> + .uV_step = (step), \
> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
> + .vsel_mask = 0x1F, \
> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
> + .stby_mask = 0x1F, \
> + }
> +
> +#define PFUZE3000_SW2_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_BUCK, \
> + .uV_step = (step), \
> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
> + .vsel_mask = 0x7, \
> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
> + .stby_mask = 0x7, \
> + }
> +
> +#define PFUZE3000_SW3_REG(_name, base, step) \
> + { \
> + .name = #_name, \
> + .type = REGULATOR_TYPE_BUCK, \
> + .uV_step = (step), \
> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
> + .vsel_mask = 0xF, \
> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
> + .stby_mask = 0xF, \
> + }
> +
> +static unsigned int pfuze100_swbst[] = {
> + 5000000, 5050000, 5100000, 5150000
> +};
> +
> +static unsigned int pfuze100_vsnvs[] = {
> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
> +};
> +
> +static unsigned int pfuze3000_vsnvs[] = {
> + -1, -1, -1, -1, -1, -1, 3000000, -1
> +};
> +
> +static unsigned int pfuze3000_sw2lo[] = {
> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
> +};
> +
> +/* PFUZE100 */
> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
> +};
> +
> +/* PFUZE200 */
> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
> +};
> +
> +/* PFUZE3000 */
> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
> +};
> +
> +#define MODE(_id, _val, _name) { \
> + .id = _id, \
> + .register_value = _val, \
> + .name = _name, \
> +}
> +
> +/* SWx Buck regulator mode */
> +static struct dm_regulator_mode pfuze_sw_modes[] = {
> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
> + MODE(APS_APS, APS_APS, "APS_APS"),
> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
> +};
> +
> +/* Boost Buck regulator mode for normal operation */
> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
> +};
> +
> +/* VGENx LDO regulator mode for normal operation */
> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
> +};
> +
> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
> + int size,
> + const char *name)
> +{
> + int i;
blank line between declarations and rest - please fix global
> + for (i = 0; i < size; desc++) {
> + if (!strcmp(desc->name, name))
> + return desc;
> + continue;
> + }
> +
> + return NULL;
> +}
> +
> +static int pfuze100_regulator_probe(struct udevice *dev)
> +{
> + struct dm_regulator_uclass_platdata *uc_pdata;
> + struct pfuze100_regulator_desc **desc = NULL;
Can't this just be a single pointer?
> +
> + desc = dev_get_platdata(dev);
> +
> + switch (dev_get_driver_data(dev_get_parent(dev))) {
> + case PFUZE100:
> + *desc = se_desc(pfuze100_regulators,
> + ARRAY_SIZE(pfuze100_regulators),
> + dev->name);
> + break;
> + case PFUZE200:
> + *desc = se_desc(pfuze200_regulators,
> + ARRAY_SIZE(pfuze200_regulators),
> + dev->name);
> + break;
> + case PFUZE3000:
> + *desc = se_desc(pfuze3000_regulators,
> + ARRAY_SIZE(pfuze3000_regulators),
> + dev->name);
> + break;
> + }
> + if (!*desc) {
> + debug("Do not support regulator %s\n", dev->name);
> + return -EINVAL;
> + }
> +
> + uc_pdata = dev_get_uclass_platdata(dev);
> +
> + uc_pdata->type = (*desc)->type;
> + if (uc_pdata->type == REGULATOR_TYPE_BUCK) {
> + if (!strcmp(dev->name, "swbst")) {
> + uc_pdata->mode = pfuze_swbst_modes;
> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_swbst_modes);
> + } else {
> + uc_pdata->mode = pfuze_sw_modes;
> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_sw_modes);
> + }
> + } else if (uc_pdata->type == REGULATOR_TYPE_LDO) {
> + uc_pdata->mode = pfuze_ldo_modes;
> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_ldo_modes);
> + } else {
> + uc_pdata->mode = NULL;
> + uc_pdata->mode_count = 0;
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_regulator_mode(struct udevice *dev, int op, int *opmode)
> +{
> + unsigned char val;
> + int ret;
> + struct pfuze100_regulator_desc *desc =
> + *(struct pfuze100_regulator_desc **)dev_get_platdata(dev);
You don't actually need the cast.
> +
> + if (op == PMIC_OP_GET) {
> + if (desc->type == REGULATOR_TYPE_BUCK) {
> + if (!strcmp(dev->name, "swbst")) {
> + ret = pmic_read(dev->parent, desc->vsel_reg,
> + &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= SWBST_MODE_MASK;
> + val >>= SWBST_MODE_SHIFT;
> + *opmode = val;
> +
> + return 0;
> + }
> + ret = pmic_read(dev->parent,
> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
> + &val, 1);
pmic_reg_read()
> + if (ret)
> + return ret;
> +
> + val &= SW_MODE_MASK;
> + val >>= SW_MODE_SHIFT;
> + *opmode = val;
> +
> + return 0;
> +
> + } else if (desc->type == REGULATOR_TYPE_LDO) {
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= LDO_MODE_MASK;
> + val >>= LDO_MODE_SHIFT;
> + *opmode = val;
> +
> + return 0;
> + } else {
> + return -EINVAL;
> + }
> + }
> +
> + if (desc->type == REGULATOR_TYPE_BUCK) {
> + if (!strcmp(dev->name, "swbst")) {
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= ~SWBST_MODE_MASK;
> + val |= *opmode << SWBST_MODE_SHIFT;
> +
> + ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
pmic_reg_write
> + if (ret)
> + return ret;
> +
> + return 0;
> + }
> + ret = pmic_read(dev->parent,
> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
> + &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= ~SW_MODE_MASK;
> + val |= *opmode << SW_MODE_SHIFT;
> +
> + ret = pmic_write(dev->parent,
> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
> + &val, 1);
pmic_clrsetbits() can replace all of this
> + if (ret)
> + return ret;
> +
> + return 0;
> + } else if (desc->type == REGULATOR_TYPE_LDO) {
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= ~LDO_MODE_MASK;
> + val |= *opmode << LDO_MODE_SHIFT;
> +
> + ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> +
> + return 0;
> + } else {
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_regulator_enable(struct udevice *dev, int op, bool *enable)
> +{
> + int ret, on_off;
> + unsigned char val;
> + struct dm_regulator_uclass_platdata *uc_pdata =
> + dev_get_uclass_platdata(dev);
> + if (op == PMIC_OP_GET) {
> + if (!strcmp(dev->name, "vrefddr")) {
> + ret = pmic_read(dev->parent, PFUZE100_VREFDDRCON,
> + &val, 1);
> + if (ret)
> + return ret;
> + if (val & VREFDDRCON_EN)
> + *enable = true;
> + else
> + *enable = false;
> + return 0;
> + }
> + ret = pfuze100_regulator_mode(dev, op, &on_off);
> + if (ret)
> + return ret;
> + switch (on_off) {
> + /* OFF_OFF, SWBST_MODE_OFF, LDO_MODE_OFF have same value */
> + case OFF_OFF:
> + *enable = false;
> + break;
> + default:
> + *enable = true;
> + break;
> + }
> + } else if (op == PMIC_OP_SET) {
> + if (!strcmp(dev->name, "vrefddr")) {
> + ret = pmic_read(dev->parent, PFUZE100_VREFDDRCON,
> + &val, 1);
> + if (ret)
> + return ret;
> +
> + if (val & VREFDDRCON_EN)
> + return 0;
> + val |= VREFDDRCON_EN;
> +
> + return pmic_write(dev->parent, PFUZE100_VREFDDRCON,
> + &val, 1);
> + }
> +
> + if (uc_pdata->type == REGULATOR_TYPE_LDO) {
> + on_off = *enable ? LDO_MODE_ON : LDO_MODE_OFF;
> + } else if (uc_pdata->type == REGULATOR_TYPE_BUCK) {
> + if (!strcmp(dev->name, "swbst"))
> + on_off = *enable ? SWBST_MODE_AUTO :
> + SWBST_MODE_OFF;
> + else
> + on_off = *enable ? APS_PFM : OFF_OFF;
> + } else {
> + return -EINVAL;
> + }
> +
> + return pfuze100_regulator_mode(dev, op, &on_off);
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_regulator_val(struct udevice *dev, int op, int *uV)
> +{
> + unsigned char val;
> + int i, ret;
> + struct pfuze100_regulator_desc *desc =
> + *(struct pfuze100_regulator_desc **)dev_get_platdata(dev);
> + struct dm_regulator_uclass_platdata *uc_pdata =
> + dev_get_uclass_platdata(dev);
> +
> + if (op == PMIC_OP_GET) {
> + *uV = 0;
> + if (uc_pdata->type == REGULATOR_TYPE_FIXED) {
> + *uV = desc->voltage;
> + } else if (desc->volt_table) {
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> + val &= desc->vsel_mask;
> + *uV = desc->volt_table[val];
> + } else {
> + if (uc_pdata->min_uV < 0) {
> + debug("Need to provide min_uV in dts.\n");
> + return -EINVAL;
> + }
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> + val &= desc->vsel_mask;
> + *uV = uc_pdata->min_uV + (int)val * desc->uV_step;
> + }
> +
> + return 0;
> + }
> +
> + if (uc_pdata->type == REGULATOR_TYPE_FIXED) {
> + debug("Set voltage for REGULATOR_TYPE_FIXED regulator\n");
> + return -EINVAL;
> + } else if (desc->volt_table) {
> + for (i = 0; i < desc->vsel_mask; i++) {
> + if (*uV == desc->volt_table[i])
> + break;
> + }
> + if (i == desc->vsel_mask) {
> + debug("Unsupported voltage %u\n", *uV);
> + return -EINVAL;
> + }
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> + val &= ~(desc->vsel_mask);
> + val |= i;
> + ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> + } else {
> + if (uc_pdata->min_uV < 0) {
> + debug("Need to provide min_uV in dts.\n");
> + return -EINVAL;
> + }
> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> +
> + val &= ~(desc->vsel_mask);
> + val |= (*uV - uc_pdata->min_uV) / desc->uV_step;
> +
> + ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_regulator_get_value(struct udevice *dev)
> +{
> + int uV;
> + int ret;
> +
> + ret = pfuze100_regulator_val(dev, PMIC_OP_GET, &uV);
> + if (ret)
> + return ret;
> +
> + return uV;
> +}
> +
> +static int pfuze100_regulator_set_value(struct udevice *dev, int uV)
> +{
> + return pfuze100_regulator_val(dev, PMIC_OP_SET, &uV);
> +}
> +
> +static bool pfuze100_regulator_get_enable(struct udevice *dev)
> +{
> + bool enable = false;
> + int ret;
> +
> + ret = pfuze100_regulator_enable(dev, PMIC_OP_GET, &enable);
> + if (ret)
> + return ret;
> +
> + return enable;
> +}
> +
> +static int pfuze100_regulator_set_enable(struct udevice *dev, bool enable)
> +{
> + return pfuze100_regulator_enable(dev, PMIC_OP_SET, &enable);
> +}
> +
> +static int pfuze100_regulator_get_mode(struct udevice *dev)
> +{
> + int mode;
> + int ret;
> +
> + ret = pfuze100_regulator_mode(dev, PMIC_OP_GET, &mode);
> + if (ret)
> + return ret;
> +
> + return mode;
> +}
> +
> +static int pfuze100_regulator_set_mode(struct udevice *dev, int mode)
> +{
> + return pfuze100_regulator_mode(dev, PMIC_OP_SET, &mode);
> +}
> +
> +static const struct dm_regulator_ops pfuze100_regulator_ops = {
> + .get_value = pfuze100_regulator_get_value,
> + .set_value = pfuze100_regulator_set_value,
> + .get_enable = pfuze100_regulator_get_enable,
> + .set_enable = pfuze100_regulator_set_enable,
> + .get_mode = pfuze100_regulator_get_mode,
> + .set_mode = pfuze100_regulator_set_mode,
> +};
> +
> +U_BOOT_DRIVER(pfuze100_regulator) = {
> + .name = "pfuze100_regulator",
> + .id = UCLASS_REGULATOR,
> + .ops = &pfuze100_regulator_ops,
> + .probe = pfuze100_regulator_probe,
> + .platdata_auto_alloc_size = sizeof(struct pfuze100_regulator_desc **),
> +};
> diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
> index b13a780..36cc212 100644
> --- a/include/power/pfuze100_pmic.h
> +++ b/include/power/pfuze100_pmic.h
> @@ -60,6 +60,13 @@ enum {
> PMIC_NUM_OF_REGS = 0x7f,
> };
>
> +/* Registor offset based on VOLT register */
> +#define PFUZE100_VOL_OFFSET 0
> +#define PFUZE100_STBY_OFFSET 1
> +#define PFUZE100_OFF_OFFSET 2
> +#define PFUZE100_MODE_OFFSET 3
> +#define PFUZE100_CONF_OFFSET 4
> +
> /*
> * Buck Regulators
> */
> @@ -136,6 +143,9 @@ enum {
> #define SW1x_STBY_MASK 0x3f
> #define SW1x_OFF_MASK 0x3f
>
> +#define SW_MODE_MASK 0xf
> +#define SW_MODE_SHIFT 0
> +
> #define SW1xCONF_DVSSPEED_MASK 0xc0
> #define SW1xCONF_DVSSPEED_2US 0x00
> #define SW1xCONF_DVSSPEED_4US 0x40
> @@ -184,7 +194,12 @@ enum {
>
> #define LDO_VOL_MASK 0xf
> #define LDO_EN (1 << 4)
> +#define LDO_MODE_SHIFT 4
> +#define LDO_MODE_MASK (1 << 4)
> +#define LDO_MODE_OFF 0
> +#define LDO_MODE_ON 1
>
> +#define VREFDDRCON_EN (1 << 4)
> /*
> * Boost Regulator
> */
> @@ -197,10 +212,11 @@ enum {
>
> #define SWBST_VOL_MASK 0x3
> #define SWBST_MODE_MASK 0xC
> -#define SWBST_MODE_OFF (0 << 2)
> -#define SWBST_MODE_PFM (1 << 2)
> -#define SWBST_MODE_AUTO (2 << 2)
> -#define SWBST_MODE_APS (3 << 2)
> +#define SWBST_MODE_SHIFT 0x2
> +#define SWBST_MODE_OFF 0
> +#define SWBST_MODE_PFM 1
> +#define SWBST_MODE_AUTO 2
> +#define SWBST_MODE_APS 3
>
> /*
> * Regulator Mode Control
> --
> 1.8.4
>
>
Regards,
Simon
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC
2015-07-28 14:48 ` [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC Peng Fan
@ 2015-08-02 22:30 ` Simon Glass
0 siblings, 0 replies; 21+ messages in thread
From: Simon Glass @ 2015-08-02 22:30 UTC (permalink / raw)
To: u-boot
On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
> If enable DM PMIC and REGULATOR, we should not use original power
> framework. So need to comment out the pfuze code for original power
> framework, when CONFIG_DM_PMIC_PFUZE100 defined.
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
> board/freescale/common/pfuze.c | 2 ++
> 1 file changed, 2 insertions(+)
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model
2015-07-28 14:48 ` [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model Peng Fan
@ 2015-08-02 22:31 ` Simon Glass
2015-08-03 15:01 ` Przemyslaw Marczak
1 sibling, 0 replies; 21+ messages in thread
From: Simon Glass @ 2015-08-02 22:31 UTC (permalink / raw)
To: u-boot
On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
> 1. Support driver model for pfuze100.
> 2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
> 3. This driver intends to support PF100, PF200 and PF3000, so add
> the device id into the udevice_id array.
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Simon Glass <sjg@chromium.org>
> ---
> drivers/power/pmic/Kconfig | 7 +++
> drivers/power/pmic/pmic_pfuze100.c | 89 ++++++++++++++++++++++++++++++++++++++
> include/power/pfuze100_pmic.h | 3 ++
> 3 files changed, 99 insertions(+)
Reviewed-by: Simon Glass <sjg@chromium.org>
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name
2015-07-28 14:48 ` [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name Peng Fan
@ 2015-08-02 22:31 ` Simon Glass
2015-08-03 0:23 ` Peng Fan
0 siblings, 1 reply; 21+ messages in thread
From: Simon Glass @ 2015-08-02 22:31 UTC (permalink / raw)
To: u-boot
Hi Peng,
On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
> If there is no property named 'regulator-name' for regulators,
> choose node name instead, but not directly return failure value.
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Simon Glass <sjg@chromium.org>
> ---
> drivers/power/regulator/regulator-uclass.c | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/power/regulator/regulator-uclass.c b/drivers/power/regulator/regulator-uclass.c
> index 12e141b..d4f06d5 100644
> --- a/drivers/power/regulator/regulator-uclass.c
> +++ b/drivers/power/regulator/regulator-uclass.c
> @@ -256,7 +256,9 @@ static int regulator_post_bind(struct udevice *dev)
> if (!uc_pdata->name) {
> debug("%s: dev: %s has no property 'regulator-name'\n",
> __func__, dev->name);
> - return -EINVAL;
> + uc_pdata->name = fdt_get_name(blob, offset, NULL);
> + if (!uc_pdata->name)
> + return -EINVAL;
> }
>
> if (regulator_name_is_unique(dev, uc_pdata->name))
> --
> 1.8.4
>
>
What is this for please? Can you point me to the device tree binding
that needs this? I suspect it is fine, but I would like to understand
the purpose.
Regards,
Simon
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name
2015-08-02 22:31 ` Simon Glass
@ 2015-08-03 0:23 ` Peng Fan
2015-08-03 15:00 ` Przemyslaw Marczak
0 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-08-03 0:23 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Sun, Aug 02, 2015 at 04:31:06PM -0600, Simon Glass wrote:
>Hi Peng,
>
>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>> If there is no property named 'regulator-name' for regulators,
>> choose node name instead, but not directly return failure value.
>>
>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>> Cc: Simon Glass <sjg@chromium.org>
>> ---
>> drivers/power/regulator/regulator-uclass.c | 4 +++-
>> 1 file changed, 3 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/power/regulator/regulator-uclass.c b/drivers/power/regulator/regulator-uclass.c
>> index 12e141b..d4f06d5 100644
>> --- a/drivers/power/regulator/regulator-uclass.c
>> +++ b/drivers/power/regulator/regulator-uclass.c
>> @@ -256,7 +256,9 @@ static int regulator_post_bind(struct udevice *dev)
>> if (!uc_pdata->name) {
>> debug("%s: dev: %s has no property 'regulator-name'\n",
>> __func__, dev->name);
>> - return -EINVAL;
>> + uc_pdata->name = fdt_get_name(blob, offset, NULL);
>> + if (!uc_pdata->name)
>> + return -EINVAL;
>> }
>>
>> if (regulator_name_is_unique(dev, uc_pdata->name))
>> --
>> 1.8.4
>>
>>
>
>What is this for please? Can you point me to the device tree binding
>that needs this? I suspect it is fine, but I would like to understand
>the purpose.
The regulator device tree is as following:
regulators {
sw1a_reg: sw1a {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1475000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
/* use sw1c_reg to align with pfuze100/pfuze200 */
sw1c_reg: sw1b {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1475000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <6250>;
};
There is no regulator-name property. From the current regulator framework,
if there is no regulator-name property, it will return -EINVAL. So,
I did this patch to use node name, if there is no regulator-name property.
Regards,
Peng.
--
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-08-02 22:30 ` Simon Glass
@ 2015-08-03 0:38 ` Peng Fan
2015-08-04 2:08 ` Peng Fan
0 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-08-03 0:38 UTC (permalink / raw)
To: u-boot
Hi Simon,
On Sun, Aug 02, 2015 at 04:30:52PM -0600, Simon Glass wrote:
>Hi Peng,
>
>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>> 1. Add new regulator driver pfuze100.
>> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
>> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
>> 3. This driver intends to support PF100, PF200 and PF3000.
>> 4. Add related macro definition in pfuze header file.
>>
>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>> Cc: Simon Glass <sjg@chromium.org>
>
>It looks correct but I have code style comments - see below. They all
>apply globally.
Ok. Will fix them in V2.
>
>> ---
>> drivers/power/regulator/Kconfig | 8 +
>> drivers/power/regulator/Makefile | 1 +
>> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
>> include/power/pfuze100_pmic.h | 24 +-
>> 4 files changed, 625 insertions(+), 4 deletions(-)
>> create mode 100644 drivers/power/regulator/pfuze100.c
>>
>> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
>> index 6289b83..b854773 100644
>> --- a/drivers/power/regulator/Kconfig
>> +++ b/drivers/power/regulator/Kconfig
>> @@ -16,6 +16,14 @@ config DM_REGULATOR
>> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
>> otherwise. Detailed information can be found in the header file.
>>
>> +config DM_REGULATOR_PFUZE100
>> + bool "Enable Driver Model for REGULATOR PFUZE100"
>> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
>> + ---help---
>> + This config enables implementation of driver-model regulator uclass
>> + features for REGULATOR PFUZE100. The driver implements get/set api for:
>> + value, enable and mode.
>> +
>> config DM_REGULATOR_MAX77686
>> bool "Enable Driver Model for REGULATOR MAX77686"
>> depends on DM_REGULATOR && DM_PMIC_MAX77686
>> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
>> index 96aa624..9f8f17b 100644
>> --- a/drivers/power/regulator/Makefile
>> +++ b/drivers/power/regulator/Makefile
>> @@ -7,5 +7,6 @@
>>
>> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
>> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
>> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
>> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
>> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
>> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
>> new file mode 100644
>> index 0000000..6c513e9
>> --- /dev/null
>> +++ b/drivers/power/regulator/pfuze100.c
>> @@ -0,0 +1,596 @@
>> +#include <common.h>
>> +#include <fdtdec.h>
>> +#include <errno.h>
>> +#include <dm.h>
>> +#include <i2c.h>
>> +#include <power/pmic.h>
>> +#include <power/regulator.h>
>> +#include <power/pfuze100_pmic.h>
>> +
>> +/**
>> + * struct pfuze100_regulator_desc - regulator descriptor
>> + *
>> + * @name: Identify name for the regulator.
>> + * @type: Indicates the regulator type.
>> + * @uV_step: Voltage increase for each selector.
>> + * @vsel_reg: Register for adjust regulator voltage for normal.
>> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
>> + * @stby_reg: Register for adjust regulator voltage for standby.
>> + * @stby_mask: Mask bit for setting regulator voltage for standby.
>> + * @volt_table: Voltage mapping table (if table based mapping).
>> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
>> + */
>> +struct pfuze100_regulator_desc {
>> + char *name;
>> + enum regulator_type type;
>> + unsigned int uV_step;
>> + unsigned int vsel_reg;
>> + unsigned int vsel_mask;
>> + unsigned int stby_reg;
>> + unsigned int stby_mask;
>> + unsigned int *volt_table;
>> + unsigned int voltage;
>> +};
>> +
>> +#define PFUZE100_FIXED_REG(_name, base, vol) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_FIXED, \
>> + .voltage = (vol), \
>> + }
>> +
>> +#define PFUZE100_SW_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_BUCK, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>> + .vsel_mask = 0x3F, \
>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>> + .stby_mask = 0x3F, \
>> + }
>> +
>> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_BUCK, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base), \
>> + .vsel_mask = (mask), \
>> + .volt_table = (voltages), \
>> + }
>> +
>> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_OTHER, \
>> + .vsel_reg = (base), \
>> + .vsel_mask = (mask), \
>> + .volt_table = (voltages), \
>> + }
>> +
>> +#define PFUZE100_VGEN_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_LDO, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base), \
>> + .vsel_mask = 0xF, \
>> + .stby_reg = (base), \
>> + .stby_mask = 0x20, \
>> + }
>> +
>> +#define PFUZE3000_VCC_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_LDO, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base), \
>> + .vsel_mask = 0x3, \
>> + .stby_reg = (base), \
>> + .stby_mask = 0x20, \
>> +}
>> +
>> +#define PFUZE3000_SW1_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_BUCK, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>> + .vsel_mask = 0x1F, \
>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>> + .stby_mask = 0x1F, \
>> + }
>> +
>> +#define PFUZE3000_SW2_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_BUCK, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>> + .vsel_mask = 0x7, \
>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>> + .stby_mask = 0x7, \
>> + }
>> +
>> +#define PFUZE3000_SW3_REG(_name, base, step) \
>> + { \
>> + .name = #_name, \
>> + .type = REGULATOR_TYPE_BUCK, \
>> + .uV_step = (step), \
>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>> + .vsel_mask = 0xF, \
>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>> + .stby_mask = 0xF, \
>> + }
>> +
>> +static unsigned int pfuze100_swbst[] = {
>> + 5000000, 5050000, 5100000, 5150000
>> +};
>> +
>> +static unsigned int pfuze100_vsnvs[] = {
>> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
>> +};
>> +
>> +static unsigned int pfuze3000_vsnvs[] = {
>> + -1, -1, -1, -1, -1, -1, 3000000, -1
>> +};
>> +
>> +static unsigned int pfuze3000_sw2lo[] = {
>> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
>> +};
>> +
>> +/* PFUZE100 */
>> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>> +};
>> +
>> +/* PFUZE200 */
>> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>> +};
>> +
>> +/* PFUZE3000 */
>> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
>> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
>> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
>> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
>> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
>> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
>> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
>> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
>> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
>> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
>> +};
>> +
>> +#define MODE(_id, _val, _name) { \
>> + .id = _id, \
>> + .register_value = _val, \
>> + .name = _name, \
>> +}
>> +
>> +/* SWx Buck regulator mode */
>> +static struct dm_regulator_mode pfuze_sw_modes[] = {
>> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
>> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
>> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
>> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
>> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
>> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
>> + MODE(APS_APS, APS_APS, "APS_APS"),
>> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
>> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
>> +};
>> +
>> +/* Boost Buck regulator mode for normal operation */
>> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
>> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
>> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
>> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
>> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
>> +};
>> +
>> +/* VGENx LDO regulator mode for normal operation */
>> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
>> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
>> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
>> +};
>> +
>> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
>> + int size,
>> + const char *name)
>> +{
>> + int i;
>
>blank line between declarations and rest - please fix global
Will fix in V2.
>
>> + for (i = 0; i < size; desc++) {
>> + if (!strcmp(desc->name, name))
>> + return desc;
>> + continue;
>> + }
>> +
>> + return NULL;
>> +}
>> +
>> +static int pfuze100_regulator_probe(struct udevice *dev)
>> +{
>> + struct dm_regulator_uclass_platdata *uc_pdata;
>> + struct pfuze100_regulator_desc **desc = NULL;
>
>Can't this just be a single pointer?
hmm. My bad, will fix this.
>
>> +
>> + desc = dev_get_platdata(dev);
>> +
>> + switch (dev_get_driver_data(dev_get_parent(dev))) {
>> + case PFUZE100:
>> + *desc = se_desc(pfuze100_regulators,
>> + ARRAY_SIZE(pfuze100_regulators),
>> + dev->name);
>> + break;
>> + case PFUZE200:
>> + *desc = se_desc(pfuze200_regulators,
>> + ARRAY_SIZE(pfuze200_regulators),
>> + dev->name);
>> + break;
>> + case PFUZE3000:
>> + *desc = se_desc(pfuze3000_regulators,
>> + ARRAY_SIZE(pfuze3000_regulators),
>> + dev->name);
>> + break;
>> + }
>> + if (!*desc) {
>> + debug("Do not support regulator %s\n", dev->name);
>> + return -EINVAL;
>> + }
>> +
>> + uc_pdata = dev_get_uclass_platdata(dev);
>> +
>> + uc_pdata->type = (*desc)->type;
>> + if (uc_pdata->type == REGULATOR_TYPE_BUCK) {
>> + if (!strcmp(dev->name, "swbst")) {
>> + uc_pdata->mode = pfuze_swbst_modes;
>> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_swbst_modes);
>> + } else {
>> + uc_pdata->mode = pfuze_sw_modes;
>> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_sw_modes);
>> + }
>> + } else if (uc_pdata->type == REGULATOR_TYPE_LDO) {
>> + uc_pdata->mode = pfuze_ldo_modes;
>> + uc_pdata->mode_count = ARRAY_SIZE(pfuze_ldo_modes);
>> + } else {
>> + uc_pdata->mode = NULL;
>> + uc_pdata->mode_count = 0;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int pfuze100_regulator_mode(struct udevice *dev, int op, int *opmode)
>> +{
>> + unsigned char val;
>> + int ret;
>> + struct pfuze100_regulator_desc *desc =
>> + *(struct pfuze100_regulator_desc **)dev_get_platdata(dev);
>
>You don't actually need the cast.
Will discard the cast.
>
>> +
>> + if (op == PMIC_OP_GET) {
>> + if (desc->type == REGULATOR_TYPE_BUCK) {
>> + if (!strcmp(dev->name, "swbst")) {
>> + ret = pmic_read(dev->parent, desc->vsel_reg,
>> + &val, 1);
>> + if (ret)
>> + return ret;
>> +
>> + val &= SWBST_MODE_MASK;
>> + val >>= SWBST_MODE_SHIFT;
>> + *opmode = val;
>> +
>> + return 0;
>> + }
>> + ret = pmic_read(dev->parent,
>> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
>> + &val, 1);
>
>pmic_reg_read()
>
>> + if (ret)
>> + return ret;
>> +
>> + val &= SW_MODE_MASK;
>> + val >>= SW_MODE_SHIFT;
>> + *opmode = val;
>> +
>> + return 0;
>> +
>> + } else if (desc->type == REGULATOR_TYPE_LDO) {
>> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
>> + if (ret)
>> + return ret;
>> +
>> + val &= LDO_MODE_MASK;
>> + val >>= LDO_MODE_SHIFT;
>> + *opmode = val;
>> +
>> + return 0;
>> + } else {
>> + return -EINVAL;
>> + }
>> + }
>> +
>> + if (desc->type == REGULATOR_TYPE_BUCK) {
>> + if (!strcmp(dev->name, "swbst")) {
>> + ret = pmic_read(dev->parent, desc->vsel_reg, &val, 1);
>> + if (ret)
>> + return ret;
>> +
>> + val &= ~SWBST_MODE_MASK;
>> + val |= *opmode << SWBST_MODE_SHIFT;
>> +
>> + ret = pmic_write(dev->parent, desc->vsel_reg, &val, 1);
>
>pmic_reg_write
Ok.
>
>> + if (ret)
>> + return ret;
>> +
>> + return 0;
>> + }
>> + ret = pmic_read(dev->parent,
>> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
>> + &val, 1);
>> + if (ret)
>> + return ret;
>> +
>> + val &= ~SW_MODE_MASK;
>> + val |= *opmode << SW_MODE_SHIFT;
>> +
>> + ret = pmic_write(dev->parent,
>> + desc->vsel_reg + PFUZE100_MODE_OFFSET,
>> + &val, 1);
>
>pmic_clrsetbits() can replace all of this
ok. Will use this new way.
[...]
Thanks,
Peng.
--
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name
2015-08-03 0:23 ` Peng Fan
@ 2015-08-03 15:00 ` Przemyslaw Marczak
2015-08-04 0:12 ` Peng Fan
0 siblings, 1 reply; 21+ messages in thread
From: Przemyslaw Marczak @ 2015-08-03 15:00 UTC (permalink / raw)
To: u-boot
Hello,
On 08/03/2015 02:23 AM, Peng Fan wrote:
> Hi Simon,
>
> On Sun, Aug 02, 2015 at 04:31:06PM -0600, Simon Glass wrote:
>> Hi Peng,
>>
>> On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>> If there is no property named 'regulator-name' for regulators,
>>> choose node name instead, but not directly return failure value.
>>>
>>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>> Cc: Simon Glass <sjg@chromium.org>
>>> ---
>>> drivers/power/regulator/regulator-uclass.c | 4 +++-
>>> 1 file changed, 3 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/power/regulator/regulator-uclass.c b/drivers/power/regulator/regulator-uclass.c
>>> index 12e141b..d4f06d5 100644
>>> --- a/drivers/power/regulator/regulator-uclass.c
>>> +++ b/drivers/power/regulator/regulator-uclass.c
>>> @@ -256,7 +256,9 @@ static int regulator_post_bind(struct udevice *dev)
>>> if (!uc_pdata->name) {
>>> debug("%s: dev: %s has no property 'regulator-name'\n",
>>> __func__, dev->name);
>>> - return -EINVAL;
>>> + uc_pdata->name = fdt_get_name(blob, offset, NULL);
>>> + if (!uc_pdata->name)
>>> + return -EINVAL;
>>> }
>>>
>>> if (regulator_name_is_unique(dev, uc_pdata->name))
>>> --
>>> 1.8.4
>>>
>>>
>>
>> What is this for please? Can you point me to the device tree binding
>> that needs this? I suspect it is fine, but I would like to understand
>> the purpose.
>
> The regulator device tree is as following:
>
> regulators {
> sw1a_reg: sw1a {
> regulator-min-microvolt = <700000>;
> regulator-max-microvolt = <1475000>;
> regulator-boot-on;
> regulator-always-on;
> regulator-ramp-delay = <6250>;
> };
>
> /* use sw1c_reg to align with pfuze100/pfuze200 */
> sw1c_reg: sw1b {
> regulator-min-microvolt = <700000>;
> regulator-max-microvolt = <1475000>;
> regulator-boot-on;
> regulator-always-on;
> regulator-ramp-delay = <6250>;
> };
>
> There is no regulator-name property. From the current regulator framework,
> if there is no regulator-name property, it will return -EINVAL. So,
> I did this patch to use node name, if there is no regulator-name property.
>
> Regards,
> Peng.
>
There are few boards in the kernel without the "regulator-name"
properties in device tree files, so this is right solution.
Please also update the comments in those files:
- include/power/regulator.h
- doc/device-tree-bindings/regulator/regulator.txt
Best regards,
--
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model
2015-07-28 14:48 ` [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model Peng Fan
2015-08-02 22:31 ` Simon Glass
@ 2015-08-03 15:01 ` Przemyslaw Marczak
2015-08-04 0:15 ` Peng Fan
1 sibling, 1 reply; 21+ messages in thread
From: Przemyslaw Marczak @ 2015-08-03 15:01 UTC (permalink / raw)
To: u-boot
Hello Peng,
I have few comments.
On 07/28/2015 04:48 PM, Peng Fan wrote:
> 1. Support driver model for pfuze100.
> 2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
> 3. This driver intends to support PF100, PF200 and PF3000, so add
> the device id into the udevice_id array.
>
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
> Cc: Simon Glass <sjg@chromium.org>
> ---
> drivers/power/pmic/Kconfig | 7 +++
> drivers/power/pmic/pmic_pfuze100.c | 89 ++++++++++++++++++++++++++++++++++++++
> include/power/pfuze100_pmic.h | 3 ++
> 3 files changed, 99 insertions(+)
>
> diff --git a/drivers/power/pmic/Kconfig b/drivers/power/pmic/Kconfig
> index 164f421..0df91be 100644
> --- a/drivers/power/pmic/Kconfig
> +++ b/drivers/power/pmic/Kconfig
> @@ -10,6 +10,13 @@ config DM_PMIC
> - 'drivers/power/pmic/pmic-uclass.c'
> - 'include/power/pmic.h'
>
> +config DM_PMIC_PFUZE100
> + bool "Enable Driver Model for PMIC PFUZE100"
> + depends on DM_PMIC
> + ---help---
> + This config enables implementation of driver-model pmic uclass features
> + for PMIC PFUZE100. The driver implements read/write operations.
> +
> config DM_PMIC_MAX77686
> bool "Enable Driver Model for PMIC MAX77686"
> depends on DM_PMIC
> diff --git a/drivers/power/pmic/pmic_pfuze100.c b/drivers/power/pmic/pmic_pfuze100.c
> index 22a04c0..be9d05c 100644
> --- a/drivers/power/pmic/pmic_pfuze100.c
> +++ b/drivers/power/pmic/pmic_pfuze100.c
Please keep the new convention of file naming and use just pfuze100.c.
Then, later we will remove the old files.
> @@ -2,15 +2,22 @@
> * Copyright (C) 2014 Gateworks Corporation
> * Tim Harvey <tharvey@gateworks.com>
> *
> + * Copyright (C) 2015 Freescale Semiconductor, Inc
> + * Peng Fan <Peng.Fan@freescale.com>
> + *
> * SPDX-License-Identifier: GPL-2.0+
> */
>
> #include <common.h>
> +#include <fdtdec.h>
> #include <errno.h>
> +#include <dm.h>
> #include <i2c.h>
> #include <power/pmic.h>
> +#include <power/regulator.h>
> #include <power/pfuze100_pmic.h>
>
> +#ifndef CONFIG_DM_PMIC
> int power_pfuze100_init(unsigned char bus)
> {
> static const char name[] = "PFUZE100";
> @@ -30,3 +37,85 @@ int power_pfuze100_init(unsigned char bus)
>
> return 0;
> }
> +#else
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static const struct pmic_child_info pmic_children_info[] = {
> + /* sw[x], swbst */
The driver name is used at two places, so could please define it in the
header?
> + { .prefix = "s", .driver = "pfuze100_regulator" },
> + /* vgen[x], vsnvs, vcc, v33, vcc_sd */
> + { .prefix = "v", .driver = "pfuze100_regulator" },
> + { },
> +};
> +
> +static int pfuze100_reg_count(struct udevice *dev)
> +{
This enum name is too general, so please add proper prefix.
> + return PMIC_NUM_OF_REGS;
> +}
> +
> +static int pfuze100_write(struct udevice *dev, uint reg, const uint8_t *buff,
> + int len)
> +{
> + if (dm_i2c_write(dev, reg, buff, len)) {
> + error("write error to device: %p register: %#x!", dev, reg);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
> +{
> + if (dm_i2c_read(dev, reg, buff, len)) {
> + error("read error from device: %p register: %#x!", dev, reg);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int pfuze100_bind(struct udevice *dev)
> +{
Please sort the variables below.
> + int regulators_node;
> + const void *blob = gd->fdt_blob;
> + int children;
> +
...snip...
Best regards,
--
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name
2015-08-03 15:00 ` Przemyslaw Marczak
@ 2015-08-04 0:12 ` Peng Fan
0 siblings, 0 replies; 21+ messages in thread
From: Peng Fan @ 2015-08-04 0:12 UTC (permalink / raw)
To: u-boot
Hello Przemyslaw,
On Mon, Aug 03, 2015 at 05:00:50PM +0200, Przemyslaw Marczak wrote:
>Hello,
>
>On 08/03/2015 02:23 AM, Peng Fan wrote:
>>Hi Simon,
>>
>>On Sun, Aug 02, 2015 at 04:31:06PM -0600, Simon Glass wrote:
>>>Hi Peng,
>>>
>>>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>>>If there is no property named 'regulator-name' for regulators,
>>>>choose node name instead, but not directly return failure value.
>>>>
>>>>Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>>>Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>>>Cc: Simon Glass <sjg@chromium.org>
>>>>---
>>>> drivers/power/regulator/regulator-uclass.c | 4 +++-
>>>> 1 file changed, 3 insertions(+), 1 deletion(-)
>>>>
>>>>diff --git a/drivers/power/regulator/regulator-uclass.c b/drivers/power/regulator/regulator-uclass.c
>>>>index 12e141b..d4f06d5 100644
>>>>--- a/drivers/power/regulator/regulator-uclass.c
>>>>+++ b/drivers/power/regulator/regulator-uclass.c
>>>>@@ -256,7 +256,9 @@ static int regulator_post_bind(struct udevice *dev)
>>>> if (!uc_pdata->name) {
>>>> debug("%s: dev: %s has no property 'regulator-name'\n",
>>>> __func__, dev->name);
>>>>- return -EINVAL;
>>>>+ uc_pdata->name = fdt_get_name(blob, offset, NULL);
>>>>+ if (!uc_pdata->name)
>>>>+ return -EINVAL;
>>>> }
>>>>
>>>> if (regulator_name_is_unique(dev, uc_pdata->name))
>>>>--
>>>>1.8.4
>>>>
>>>>
>>>
>>>What is this for please? Can you point me to the device tree binding
>>>that needs this? I suspect it is fine, but I would like to understand
>>>the purpose.
>>
>>The regulator device tree is as following:
>>
>> regulators {
>> sw1a_reg: sw1a {
>> regulator-min-microvolt = <700000>;
>> regulator-max-microvolt = <1475000>;
>> regulator-boot-on;
>> regulator-always-on;
>> regulator-ramp-delay = <6250>;
>> };
>>
>> /* use sw1c_reg to align with pfuze100/pfuze200 */
>> sw1c_reg: sw1b {
>> regulator-min-microvolt = <700000>;
>> regulator-max-microvolt = <1475000>;
>> regulator-boot-on;
>> regulator-always-on;
>> regulator-ramp-delay = <6250>;
>> };
>>
>>There is no regulator-name property. From the current regulator framework,
>>if there is no regulator-name property, it will return -EINVAL. So,
>>I did this patch to use node name, if there is no regulator-name property.
>>
>>Regards,
>>Peng.
>>
>
>There are few boards in the kernel without the "regulator-name"
>properties in device tree files, so this is right solution.
>
>Please also update the comments in those files:
>- include/power/regulator.h
>- doc/device-tree-bindings/regulator/regulator.txt
Ok. I'll do this, but I prefer to make the documentation update a single patch.
Regards,
Peng.
>
>Best regards,
>--
>Przemyslaw Marczak
>Samsung R&D Institute Poland
>Samsung Electronics
>p.marczak at samsung.com
--
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model
2015-08-03 15:01 ` Przemyslaw Marczak
@ 2015-08-04 0:15 ` Peng Fan
0 siblings, 0 replies; 21+ messages in thread
From: Peng Fan @ 2015-08-04 0:15 UTC (permalink / raw)
To: u-boot
Hello Przemyslaw,
On Mon, Aug 03, 2015 at 05:01:12PM +0200, Przemyslaw Marczak wrote:
>Hello Peng,
>
>I have few comments.
>
>On 07/28/2015 04:48 PM, Peng Fan wrote:
>>1. Support driver model for pfuze100.
>>2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
>>3. This driver intends to support PF100, PF200 and PF3000, so add
>> the device id into the udevice_id array.
>>
>>Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>Cc: Simon Glass <sjg@chromium.org>
>>---
>> drivers/power/pmic/Kconfig | 7 +++
>> drivers/power/pmic/pmic_pfuze100.c | 89 ++++++++++++++++++++++++++++++++++++++
>> include/power/pfuze100_pmic.h | 3 ++
>> 3 files changed, 99 insertions(+)
>>
>>diff --git a/drivers/power/pmic/Kconfig b/drivers/power/pmic/Kconfig
>>index 164f421..0df91be 100644
>>--- a/drivers/power/pmic/Kconfig
>>+++ b/drivers/power/pmic/Kconfig
>>@@ -10,6 +10,13 @@ config DM_PMIC
>> - 'drivers/power/pmic/pmic-uclass.c'
>> - 'include/power/pmic.h'
>>
>>+config DM_PMIC_PFUZE100
>>+ bool "Enable Driver Model for PMIC PFUZE100"
>>+ depends on DM_PMIC
>>+ ---help---
>>+ This config enables implementation of driver-model pmic uclass features
>>+ for PMIC PFUZE100. The driver implements read/write operations.
>>+
>> config DM_PMIC_MAX77686
>> bool "Enable Driver Model for PMIC MAX77686"
>> depends on DM_PMIC
>>diff --git a/drivers/power/pmic/pmic_pfuze100.c b/drivers/power/pmic/pmic_pfuze100.c
>>index 22a04c0..be9d05c 100644
>>--- a/drivers/power/pmic/pmic_pfuze100.c
>>+++ b/drivers/power/pmic/pmic_pfuze100.c
>
>Please keep the new convention of file naming and use just
>pfuze100.c. Then, later we will remove the old files.
Ok. Will rename the file to pfuze100.c in V2.
>
>>@@ -2,15 +2,22 @@
>> * Copyright (C) 2014 Gateworks Corporation
>> * Tim Harvey <tharvey@gateworks.com>
>> *
>>+ * Copyright (C) 2015 Freescale Semiconductor, Inc
>>+ * Peng Fan <Peng.Fan@freescale.com>
>>+ *
>> * SPDX-License-Identifier: GPL-2.0+
>> */
>>
>> #include <common.h>
>>+#include <fdtdec.h>
>> #include <errno.h>
>>+#include <dm.h>
>> #include <i2c.h>
>> #include <power/pmic.h>
>>+#include <power/regulator.h>
>> #include <power/pfuze100_pmic.h>
>>
>>+#ifndef CONFIG_DM_PMIC
>> int power_pfuze100_init(unsigned char bus)
>> {
>> static const char name[] = "PFUZE100";
>>@@ -30,3 +37,85 @@ int power_pfuze100_init(unsigned char bus)
>>
>> return 0;
>> }
>>+#else
>>+DECLARE_GLOBAL_DATA_PTR;
>>+
>>+static const struct pmic_child_info pmic_children_info[] = {
>>+ /* sw[x], swbst */
>
>The driver name is used at two places, so could please define it in
>the header?
Ok. Will fix in V2.
>
>>+ { .prefix = "s", .driver = "pfuze100_regulator" },
>>+ /* vgen[x], vsnvs, vcc, v33, vcc_sd */
>>+ { .prefix = "v", .driver = "pfuze100_regulator" },
>>+ { },
>>+};
>>+
>>+static int pfuze100_reg_count(struct udevice *dev)
>>+{
>
>This enum name is too general, so please add proper prefix.
Will fix this in V2.
>
>>+ return PMIC_NUM_OF_REGS;
>>+}
>>+
>>+static int pfuze100_write(struct udevice *dev, uint reg, const uint8_t *buff,
>>+ int len)
>>+{
>>+ if (dm_i2c_write(dev, reg, buff, len)) {
>>+ error("write error to device: %p register: %#x!", dev, reg);
>>+ return -EIO;
>>+ }
>>+
>>+ return 0;
>>+}
>>+
>>+static int pfuze100_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
>>+{
>>+ if (dm_i2c_read(dev, reg, buff, len)) {
>>+ error("read error from device: %p register: %#x!", dev, reg);
>>+ return -EIO;
>>+ }
>>+
>>+ return 0;
>>+}
>>+
>>+static int pfuze100_bind(struct udevice *dev)
>>+{
>
>Please sort the variables below.
Ok.
[...]
Regards,
Peng.
--
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-08-03 0:38 ` Peng Fan
@ 2015-08-04 2:08 ` Peng Fan
2015-08-04 12:46 ` Simon Glass
0 siblings, 1 reply; 21+ messages in thread
From: Peng Fan @ 2015-08-04 2:08 UTC (permalink / raw)
To: u-boot
On Mon, Aug 03, 2015 at 08:38:49AM +0800, Peng Fan wrote:
>Hi Simon,
>On Sun, Aug 02, 2015 at 04:30:52PM -0600, Simon Glass wrote:
>>Hi Peng,
>>
>>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>> 1. Add new regulator driver pfuze100.
>>> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
>>> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
>>> 3. This driver intends to support PF100, PF200 and PF3000.
>>> 4. Add related macro definition in pfuze header file.
>>>
>>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>> Cc: Simon Glass <sjg@chromium.org>
>>
>>It looks correct but I have code style comments - see below. They all
>>apply globally.
>
>Ok. Will fix them in V2.
>
>>
>>> ---
>>> drivers/power/regulator/Kconfig | 8 +
>>> drivers/power/regulator/Makefile | 1 +
>>> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
>>> include/power/pfuze100_pmic.h | 24 +-
>>> 4 files changed, 625 insertions(+), 4 deletions(-)
>>> create mode 100644 drivers/power/regulator/pfuze100.c
>>>
>>> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
>>> index 6289b83..b854773 100644
>>> --- a/drivers/power/regulator/Kconfig
>>> +++ b/drivers/power/regulator/Kconfig
>>> @@ -16,6 +16,14 @@ config DM_REGULATOR
>>> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
>>> otherwise. Detailed information can be found in the header file.
>>>
>>> +config DM_REGULATOR_PFUZE100
>>> + bool "Enable Driver Model for REGULATOR PFUZE100"
>>> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
>>> + ---help---
>>> + This config enables implementation of driver-model regulator uclass
>>> + features for REGULATOR PFUZE100. The driver implements get/set api for:
>>> + value, enable and mode.
>>> +
>>> config DM_REGULATOR_MAX77686
>>> bool "Enable Driver Model for REGULATOR MAX77686"
>>> depends on DM_REGULATOR && DM_PMIC_MAX77686
>>> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
>>> index 96aa624..9f8f17b 100644
>>> --- a/drivers/power/regulator/Makefile
>>> +++ b/drivers/power/regulator/Makefile
>>> @@ -7,5 +7,6 @@
>>>
>>> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
>>> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
>>> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
>>> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
>>> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
>>> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
>>> new file mode 100644
>>> index 0000000..6c513e9
>>> --- /dev/null
>>> +++ b/drivers/power/regulator/pfuze100.c
>>> @@ -0,0 +1,596 @@
>>> +#include <common.h>
>>> +#include <fdtdec.h>
>>> +#include <errno.h>
>>> +#include <dm.h>
>>> +#include <i2c.h>
>>> +#include <power/pmic.h>
>>> +#include <power/regulator.h>
>>> +#include <power/pfuze100_pmic.h>
>>> +
>>> +/**
>>> + * struct pfuze100_regulator_desc - regulator descriptor
>>> + *
>>> + * @name: Identify name for the regulator.
>>> + * @type: Indicates the regulator type.
>>> + * @uV_step: Voltage increase for each selector.
>>> + * @vsel_reg: Register for adjust regulator voltage for normal.
>>> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
>>> + * @stby_reg: Register for adjust regulator voltage for standby.
>>> + * @stby_mask: Mask bit for setting regulator voltage for standby.
>>> + * @volt_table: Voltage mapping table (if table based mapping).
>>> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
>>> + */
>>> +struct pfuze100_regulator_desc {
>>> + char *name;
>>> + enum regulator_type type;
>>> + unsigned int uV_step;
>>> + unsigned int vsel_reg;
>>> + unsigned int vsel_mask;
>>> + unsigned int stby_reg;
>>> + unsigned int stby_mask;
>>> + unsigned int *volt_table;
>>> + unsigned int voltage;
>>> +};
>>> +
>>> +#define PFUZE100_FIXED_REG(_name, base, vol) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_FIXED, \
>>> + .voltage = (vol), \
>>> + }
>>> +
>>> +#define PFUZE100_SW_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_BUCK, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>> + .vsel_mask = 0x3F, \
>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>> + .stby_mask = 0x3F, \
>>> + }
>>> +
>>> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_BUCK, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base), \
>>> + .vsel_mask = (mask), \
>>> + .volt_table = (voltages), \
>>> + }
>>> +
>>> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_OTHER, \
>>> + .vsel_reg = (base), \
>>> + .vsel_mask = (mask), \
>>> + .volt_table = (voltages), \
>>> + }
>>> +
>>> +#define PFUZE100_VGEN_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_LDO, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base), \
>>> + .vsel_mask = 0xF, \
>>> + .stby_reg = (base), \
>>> + .stby_mask = 0x20, \
>>> + }
>>> +
>>> +#define PFUZE3000_VCC_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_LDO, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base), \
>>> + .vsel_mask = 0x3, \
>>> + .stby_reg = (base), \
>>> + .stby_mask = 0x20, \
>>> +}
>>> +
>>> +#define PFUZE3000_SW1_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_BUCK, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>> + .vsel_mask = 0x1F, \
>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>> + .stby_mask = 0x1F, \
>>> + }
>>> +
>>> +#define PFUZE3000_SW2_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_BUCK, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>> + .vsel_mask = 0x7, \
>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>> + .stby_mask = 0x7, \
>>> + }
>>> +
>>> +#define PFUZE3000_SW3_REG(_name, base, step) \
>>> + { \
>>> + .name = #_name, \
>>> + .type = REGULATOR_TYPE_BUCK, \
>>> + .uV_step = (step), \
>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>> + .vsel_mask = 0xF, \
>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>> + .stby_mask = 0xF, \
>>> + }
>>> +
>>> +static unsigned int pfuze100_swbst[] = {
>>> + 5000000, 5050000, 5100000, 5150000
>>> +};
>>> +
>>> +static unsigned int pfuze100_vsnvs[] = {
>>> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
>>> +};
>>> +
>>> +static unsigned int pfuze3000_vsnvs[] = {
>>> + -1, -1, -1, -1, -1, -1, 3000000, -1
>>> +};
>>> +
>>> +static unsigned int pfuze3000_sw2lo[] = {
>>> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
>>> +};
>>> +
>>> +/* PFUZE100 */
>>> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>> +};
>>> +
>>> +/* PFUZE200 */
>>> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>> +};
>>> +
>>> +/* PFUZE3000 */
>>> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
>>> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
>>> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
>>> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
>>> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
>>> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
>>> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
>>> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
>>> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
>>> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
>>> +};
>>> +
>>> +#define MODE(_id, _val, _name) { \
>>> + .id = _id, \
>>> + .register_value = _val, \
>>> + .name = _name, \
>>> +}
>>> +
>>> +/* SWx Buck regulator mode */
>>> +static struct dm_regulator_mode pfuze_sw_modes[] = {
>>> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
>>> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
>>> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
>>> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
>>> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
>>> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
>>> + MODE(APS_APS, APS_APS, "APS_APS"),
>>> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
>>> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
>>> +};
>>> +
>>> +/* Boost Buck regulator mode for normal operation */
>>> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
>>> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
>>> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
>>> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
>>> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
>>> +};
>>> +
>>> +/* VGENx LDO regulator mode for normal operation */
>>> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
>>> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
>>> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
>>> +};
>>> +
>>> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
>>> + int size,
>>> + const char *name)
>>> +{
>>> + int i;
>>
>>blank line between declarations and rest - please fix global
>
>Will fix in V2.
>
>>
>>> + for (i = 0; i < size; desc++) {
>>> + if (!strcmp(desc->name, name))
>>> + return desc;
>>> + continue;
>>> + }
>>> +
>>> + return NULL;
>>> +}
>>> +
>>> +static int pfuze100_regulator_probe(struct udevice *dev)
>>> +{
>>> + struct dm_regulator_uclass_platdata *uc_pdata;
>>> + struct pfuze100_regulator_desc **desc = NULL;
>>
>>Can't this just be a single pointer?
After a thought, a single pointer can not make it work.
struct pfuze100_regulator_desc is for per regulator.
If use a single pointer, then "desc = dev_get_platdata(dev);" can not
change the platdata for each regulator. I need to use "struct xx **" to
reflect the change into platdata for each regulator.
[...]
Regards,
Peng.
--
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-08-04 2:08 ` Peng Fan
@ 2015-08-04 12:46 ` Simon Glass
2015-08-04 13:16 ` Przemyslaw Marczak
2015-08-04 13:16 ` Peng Fan
0 siblings, 2 replies; 21+ messages in thread
From: Simon Glass @ 2015-08-04 12:46 UTC (permalink / raw)
To: u-boot
Hi Peng,
On 3 August 2015 at 20:08, Peng Fan <b51431@freescale.com> wrote:
> On Mon, Aug 03, 2015 at 08:38:49AM +0800, Peng Fan wrote:
>>Hi Simon,
>>On Sun, Aug 02, 2015 at 04:30:52PM -0600, Simon Glass wrote:
>>>Hi Peng,
>>>
>>>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>>> 1. Add new regulator driver pfuze100.
>>>> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
>>>> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
>>>> 3. This driver intends to support PF100, PF200 and PF3000.
>>>> 4. Add related macro definition in pfuze header file.
>>>>
>>>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>>> Cc: Simon Glass <sjg@chromium.org>
>>>
>>>It looks correct but I have code style comments - see below. They all
>>>apply globally.
>>
>>Ok. Will fix them in V2.
>>
>>>
>>>> ---
>>>> drivers/power/regulator/Kconfig | 8 +
>>>> drivers/power/regulator/Makefile | 1 +
>>>> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
>>>> include/power/pfuze100_pmic.h | 24 +-
>>>> 4 files changed, 625 insertions(+), 4 deletions(-)
>>>> create mode 100644 drivers/power/regulator/pfuze100.c
>>>>
>>>> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
>>>> index 6289b83..b854773 100644
>>>> --- a/drivers/power/regulator/Kconfig
>>>> +++ b/drivers/power/regulator/Kconfig
>>>> @@ -16,6 +16,14 @@ config DM_REGULATOR
>>>> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
>>>> otherwise. Detailed information can be found in the header file.
>>>>
>>>> +config DM_REGULATOR_PFUZE100
>>>> + bool "Enable Driver Model for REGULATOR PFUZE100"
>>>> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
>>>> + ---help---
>>>> + This config enables implementation of driver-model regulator uclass
>>>> + features for REGULATOR PFUZE100. The driver implements get/set api for:
>>>> + value, enable and mode.
>>>> +
>>>> config DM_REGULATOR_MAX77686
>>>> bool "Enable Driver Model for REGULATOR MAX77686"
>>>> depends on DM_REGULATOR && DM_PMIC_MAX77686
>>>> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
>>>> index 96aa624..9f8f17b 100644
>>>> --- a/drivers/power/regulator/Makefile
>>>> +++ b/drivers/power/regulator/Makefile
>>>> @@ -7,5 +7,6 @@
>>>>
>>>> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
>>>> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
>>>> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
>>>> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
>>>> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
>>>> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
>>>> new file mode 100644
>>>> index 0000000..6c513e9
>>>> --- /dev/null
>>>> +++ b/drivers/power/regulator/pfuze100.c
>>>> @@ -0,0 +1,596 @@
>>>> +#include <common.h>
>>>> +#include <fdtdec.h>
>>>> +#include <errno.h>
>>>> +#include <dm.h>
>>>> +#include <i2c.h>
>>>> +#include <power/pmic.h>
>>>> +#include <power/regulator.h>
>>>> +#include <power/pfuze100_pmic.h>
>>>> +
>>>> +/**
>>>> + * struct pfuze100_regulator_desc - regulator descriptor
>>>> + *
>>>> + * @name: Identify name for the regulator.
>>>> + * @type: Indicates the regulator type.
>>>> + * @uV_step: Voltage increase for each selector.
>>>> + * @vsel_reg: Register for adjust regulator voltage for normal.
>>>> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
>>>> + * @stby_reg: Register for adjust regulator voltage for standby.
>>>> + * @stby_mask: Mask bit for setting regulator voltage for standby.
>>>> + * @volt_table: Voltage mapping table (if table based mapping).
>>>> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
>>>> + */
>>>> +struct pfuze100_regulator_desc {
>>>> + char *name;
>>>> + enum regulator_type type;
>>>> + unsigned int uV_step;
>>>> + unsigned int vsel_reg;
>>>> + unsigned int vsel_mask;
>>>> + unsigned int stby_reg;
>>>> + unsigned int stby_mask;
>>>> + unsigned int *volt_table;
>>>> + unsigned int voltage;
>>>> +};
>>>> +
>>>> +#define PFUZE100_FIXED_REG(_name, base, vol) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_FIXED, \
>>>> + .voltage = (vol), \
>>>> + }
>>>> +
>>>> +#define PFUZE100_SW_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>> + .vsel_mask = 0x3F, \
>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>> + .stby_mask = 0x3F, \
>>>> + }
>>>> +
>>>> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base), \
>>>> + .vsel_mask = (mask), \
>>>> + .volt_table = (voltages), \
>>>> + }
>>>> +
>>>> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_OTHER, \
>>>> + .vsel_reg = (base), \
>>>> + .vsel_mask = (mask), \
>>>> + .volt_table = (voltages), \
>>>> + }
>>>> +
>>>> +#define PFUZE100_VGEN_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_LDO, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base), \
>>>> + .vsel_mask = 0xF, \
>>>> + .stby_reg = (base), \
>>>> + .stby_mask = 0x20, \
>>>> + }
>>>> +
>>>> +#define PFUZE3000_VCC_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_LDO, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base), \
>>>> + .vsel_mask = 0x3, \
>>>> + .stby_reg = (base), \
>>>> + .stby_mask = 0x20, \
>>>> +}
>>>> +
>>>> +#define PFUZE3000_SW1_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>> + .vsel_mask = 0x1F, \
>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>> + .stby_mask = 0x1F, \
>>>> + }
>>>> +
>>>> +#define PFUZE3000_SW2_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>> + .vsel_mask = 0x7, \
>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>> + .stby_mask = 0x7, \
>>>> + }
>>>> +
>>>> +#define PFUZE3000_SW3_REG(_name, base, step) \
>>>> + { \
>>>> + .name = #_name, \
>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>> + .uV_step = (step), \
>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>> + .vsel_mask = 0xF, \
>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>> + .stby_mask = 0xF, \
>>>> + }
>>>> +
>>>> +static unsigned int pfuze100_swbst[] = {
>>>> + 5000000, 5050000, 5100000, 5150000
>>>> +};
>>>> +
>>>> +static unsigned int pfuze100_vsnvs[] = {
>>>> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
>>>> +};
>>>> +
>>>> +static unsigned int pfuze3000_vsnvs[] = {
>>>> + -1, -1, -1, -1, -1, -1, 3000000, -1
>>>> +};
>>>> +
>>>> +static unsigned int pfuze3000_sw2lo[] = {
>>>> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
>>>> +};
>>>> +
>>>> +/* PFUZE100 */
>>>> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>> +};
>>>> +
>>>> +/* PFUZE200 */
>>>> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>> +};
>>>> +
>>>> +/* PFUZE3000 */
>>>> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
>>>> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
>>>> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
>>>> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
>>>> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
>>>> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
>>>> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
>>>> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
>>>> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
>>>> +};
>>>> +
>>>> +#define MODE(_id, _val, _name) { \
>>>> + .id = _id, \
>>>> + .register_value = _val, \
>>>> + .name = _name, \
>>>> +}
>>>> +
>>>> +/* SWx Buck regulator mode */
>>>> +static struct dm_regulator_mode pfuze_sw_modes[] = {
>>>> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
>>>> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
>>>> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
>>>> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
>>>> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
>>>> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
>>>> + MODE(APS_APS, APS_APS, "APS_APS"),
>>>> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
>>>> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
>>>> +};
>>>> +
>>>> +/* Boost Buck regulator mode for normal operation */
>>>> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
>>>> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
>>>> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
>>>> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
>>>> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
>>>> +};
>>>> +
>>>> +/* VGENx LDO regulator mode for normal operation */
>>>> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
>>>> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
>>>> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
>>>> +};
>>>> +
>>>> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
>>>> + int size,
>>>> + const char *name)
>>>> +{
>>>> + int i;
>>>
>>>blank line between declarations and rest - please fix global
>>
>>Will fix in V2.
>>
>>>
>>>> + for (i = 0; i < size; desc++) {
>>>> + if (!strcmp(desc->name, name))
>>>> + return desc;
>>>> + continue;
>>>> + }
>>>> +
>>>> + return NULL;
>>>> +}
>>>> +
>>>> +static int pfuze100_regulator_probe(struct udevice *dev)
>>>> +{
>>>> + struct dm_regulator_uclass_platdata *uc_pdata;
>>>> + struct pfuze100_regulator_desc **desc = NULL;
>>>
>>>Can't this just be a single pointer?
>
> After a thought, a single pointer can not make it work.
>
> struct pfuze100_regulator_desc is for per regulator.
> If use a single pointer, then "desc = dev_get_platdata(dev);" can not
> change the platdata for each regulator. I need to use "struct xx **" to
> reflect the change into platdata for each regulator.
>
> [...]
>
>
I see that you a searching your table based the device name. Normally
we name the regulators LDO1, LDO2 and use the number (1, 2) to find
the right device. Can you please point me to your device tree
contents?
You could make the platdata be something like
struct pfuze_platdata {
struct pfuze100_regulator_desc *desc;
};
I think the code would be clearer that way. You can assign to the desc
member instead of a double pointer indirect.
Regards,
Simon
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-08-04 12:46 ` Simon Glass
@ 2015-08-04 13:16 ` Przemyslaw Marczak
2015-08-04 13:16 ` Peng Fan
1 sibling, 0 replies; 21+ messages in thread
From: Przemyslaw Marczak @ 2015-08-04 13:16 UTC (permalink / raw)
To: u-boot
Hello Simon,
On 08/04/2015 02:46 PM, Simon Glass wrote:
> Hi Peng,
>
> On 3 August 2015 at 20:08, Peng Fan <b51431@freescale.com> wrote:
>> On Mon, Aug 03, 2015 at 08:38:49AM +0800, Peng Fan wrote:
>>> Hi Simon,
>>> On Sun, Aug 02, 2015 at 04:30:52PM -0600, Simon Glass wrote:
>>>> Hi Peng,
>>>>
>>>> On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>>>> 1. Add new regulator driver pfuze100.
>>>>> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
>>>>> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
>>>>> 3. This driver intends to support PF100, PF200 and PF3000.
>>>>> 4. Add related macro definition in pfuze header file.
>>>>>
>>>>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>>>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>>>> Cc: Simon Glass <sjg@chromium.org>
>>>>
>>>> It looks correct but I have code style comments - see below. They all
>>>> apply globally.
>>>
>>> Ok. Will fix them in V2.
>>>
>>>>
>>>>> ---
>>>>> drivers/power/regulator/Kconfig | 8 +
>>>>> drivers/power/regulator/Makefile | 1 +
>>>>> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
>>>>> include/power/pfuze100_pmic.h | 24 +-
>>>>> 4 files changed, 625 insertions(+), 4 deletions(-)
>>>>> create mode 100644 drivers/power/regulator/pfuze100.c
>>>>>
>>>>> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
>>>>> index 6289b83..b854773 100644
>>>>> --- a/drivers/power/regulator/Kconfig
>>>>> +++ b/drivers/power/regulator/Kconfig
>>>>> @@ -16,6 +16,14 @@ config DM_REGULATOR
>>>>> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
>>>>> otherwise. Detailed information can be found in the header file.
>>>>>
>>>>> +config DM_REGULATOR_PFUZE100
>>>>> + bool "Enable Driver Model for REGULATOR PFUZE100"
>>>>> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
>>>>> + ---help---
>>>>> + This config enables implementation of driver-model regulator uclass
>>>>> + features for REGULATOR PFUZE100. The driver implements get/set api for:
>>>>> + value, enable and mode.
>>>>> +
>>>>> config DM_REGULATOR_MAX77686
>>>>> bool "Enable Driver Model for REGULATOR MAX77686"
>>>>> depends on DM_REGULATOR && DM_PMIC_MAX77686
>>>>> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
>>>>> index 96aa624..9f8f17b 100644
>>>>> --- a/drivers/power/regulator/Makefile
>>>>> +++ b/drivers/power/regulator/Makefile
>>>>> @@ -7,5 +7,6 @@
>>>>>
>>>>> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
>>>>> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
>>>>> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
>>>>> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
>>>>> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
>>>>> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
>>>>> new file mode 100644
>>>>> index 0000000..6c513e9
>>>>> --- /dev/null
>>>>> +++ b/drivers/power/regulator/pfuze100.c
>>>>> @@ -0,0 +1,596 @@
>>>>> +#include <common.h>
>>>>> +#include <fdtdec.h>
>>>>> +#include <errno.h>
>>>>> +#include <dm.h>
>>>>> +#include <i2c.h>
>>>>> +#include <power/pmic.h>
>>>>> +#include <power/regulator.h>
>>>>> +#include <power/pfuze100_pmic.h>
>>>>> +
>>>>> +/**
>>>>> + * struct pfuze100_regulator_desc - regulator descriptor
>>>>> + *
>>>>> + * @name: Identify name for the regulator.
>>>>> + * @type: Indicates the regulator type.
>>>>> + * @uV_step: Voltage increase for each selector.
>>>>> + * @vsel_reg: Register for adjust regulator voltage for normal.
>>>>> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
>>>>> + * @stby_reg: Register for adjust regulator voltage for standby.
>>>>> + * @stby_mask: Mask bit for setting regulator voltage for standby.
>>>>> + * @volt_table: Voltage mapping table (if table based mapping).
>>>>> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
>>>>> + */
>>>>> +struct pfuze100_regulator_desc {
>>>>> + char *name;
>>>>> + enum regulator_type type;
>>>>> + unsigned int uV_step;
>>>>> + unsigned int vsel_reg;
>>>>> + unsigned int vsel_mask;
>>>>> + unsigned int stby_reg;
>>>>> + unsigned int stby_mask;
>>>>> + unsigned int *volt_table;
>>>>> + unsigned int voltage;
>>>>> +};
>>>>> +
>>>>> +#define PFUZE100_FIXED_REG(_name, base, vol) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_FIXED, \
>>>>> + .voltage = (vol), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SW_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x3F, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x3F, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = (mask), \
>>>>> + .volt_table = (voltages), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_OTHER, \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = (mask), \
>>>>> + .volt_table = (voltages), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_VGEN_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_LDO, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = 0xF, \
>>>>> + .stby_reg = (base), \
>>>>> + .stby_mask = 0x20, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_VCC_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_LDO, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = 0x3, \
>>>>> + .stby_reg = (base), \
>>>>> + .stby_mask = 0x20, \
>>>>> +}
>>>>> +
>>>>> +#define PFUZE3000_SW1_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x1F, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x1F, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_SW2_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x7, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x7, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_SW3_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0xF, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0xF, \
>>>>> + }
>>>>> +
>>>>> +static unsigned int pfuze100_swbst[] = {
>>>>> + 5000000, 5050000, 5100000, 5150000
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze100_vsnvs[] = {
>>>>> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze3000_vsnvs[] = {
>>>>> + -1, -1, -1, -1, -1, -1, 3000000, -1
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze3000_sw2lo[] = {
>>>>> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
>>>>> +};
>>>>> +
>>>>> +/* PFUZE100 */
>>>>> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
>>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +/* PFUZE200 */
>>>>> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
>>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +/* PFUZE3000 */
>>>>> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
>>>>> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
>>>>> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
>>>>> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
>>>>> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
>>>>> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +#define MODE(_id, _val, _name) { \
>>>>> + .id = _id, \
>>>>> + .register_value = _val, \
>>>>> + .name = _name, \
>>>>> +}
>>>>> +
>>>>> +/* SWx Buck regulator mode */
>>>>> +static struct dm_regulator_mode pfuze_sw_modes[] = {
>>>>> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
>>>>> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
>>>>> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
>>>>> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
>>>>> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
>>>>> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
>>>>> + MODE(APS_APS, APS_APS, "APS_APS"),
>>>>> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
>>>>> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
>>>>> +};
>>>>> +
>>>>> +/* Boost Buck regulator mode for normal operation */
>>>>> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
>>>>> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
>>>>> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
>>>>> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
>>>>> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
>>>>> +};
>>>>> +
>>>>> +/* VGENx LDO regulator mode for normal operation */
>>>>> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
>>>>> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
>>>>> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
>>>>> +};
>>>>> +
>>>>> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
>>>>> + int size,
>>>>> + const char *name)
>>>>> +{
>>>>> + int i;
>>>>
>>>> blank line between declarations and rest - please fix global
>>>
>>> Will fix in V2.
>>>
>>>>
>>>>> + for (i = 0; i < size; desc++) {
>>>>> + if (!strcmp(desc->name, name))
>>>>> + return desc;
>>>>> + continue;
>>>>> + }
>>>>> +
>>>>> + return NULL;
>>>>> +}
>>>>> +
>>>>> +static int pfuze100_regulator_probe(struct udevice *dev)
>>>>> +{
>>>>> + struct dm_regulator_uclass_platdata *uc_pdata;
>>>>> + struct pfuze100_regulator_desc **desc = NULL;
>>>>
>>>> Can't this just be a single pointer?
>>
>> After a thought, a single pointer can not make it work.
>>
>> struct pfuze100_regulator_desc is for per regulator.
>> If use a single pointer, then "desc = dev_get_platdata(dev);" can not
>> change the platdata for each regulator. I need to use "struct xx **" to
>> reflect the change into platdata for each regulator.
>>
>> [...]
>>
>>
>
> I see that you a searching your table based the device name. Normally
> we name the regulators LDO1, LDO2 and use the number (1, 2) to find
> the right device. Can you please point me to your device tree
> contents?
>
> You could make the platdata be something like
>
> struct pfuze_platdata {
> struct pfuze100_regulator_desc *desc;
> };
>
> I think the code would be clearer that way. You can assign to the desc
> member instead of a double pointer indirect.
>
> Regards,
> Simon
>
I think, that we can use a single pointer for this, because function
se_desc() returns a pointer to the single descriptor, for each regulator
device. Please look at my comments to this patch.
Best regards,
--
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com
^ permalink raw reply [flat|nested] 21+ messages in thread
* [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support
2015-08-04 12:46 ` Simon Glass
2015-08-04 13:16 ` Przemyslaw Marczak
@ 2015-08-04 13:16 ` Peng Fan
1 sibling, 0 replies; 21+ messages in thread
From: Peng Fan @ 2015-08-04 13:16 UTC (permalink / raw)
To: u-boot
On Tue, Aug 04, 2015 at 06:46:09AM -0600, Simon Glass wrote:
>Hi Peng,
>
>On 3 August 2015 at 20:08, Peng Fan <b51431@freescale.com> wrote:
>> On Mon, Aug 03, 2015 at 08:38:49AM +0800, Peng Fan wrote:
>>>Hi Simon,
>>>On Sun, Aug 02, 2015 at 04:30:52PM -0600, Simon Glass wrote:
>>>>Hi Peng,
>>>>
>>>>On 28 July 2015 at 08:48, Peng Fan <Peng.Fan@freescale.com> wrote:
>>>>> 1. Add new regulator driver pfuze100.
>>>>> * Introduce struct pfuze100_regulator_desc for mataining info for regulator.
>>>>> 2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
>>>>> 3. This driver intends to support PF100, PF200 and PF3000.
>>>>> 4. Add related macro definition in pfuze header file.
>>>>>
>>>>> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
>>>>> Cc: Przemyslaw Marczak <p.marczak@samsung.com>
>>>>> Cc: Simon Glass <sjg@chromium.org>
>>>>
>>>>It looks correct but I have code style comments - see below. They all
>>>>apply globally.
>>>
>>>Ok. Will fix them in V2.
>>>
>>>>
>>>>> ---
>>>>> drivers/power/regulator/Kconfig | 8 +
>>>>> drivers/power/regulator/Makefile | 1 +
>>>>> drivers/power/regulator/pfuze100.c | 596 +++++++++++++++++++++++++++++++++++++
>>>>> include/power/pfuze100_pmic.h | 24 +-
>>>>> 4 files changed, 625 insertions(+), 4 deletions(-)
>>>>> create mode 100644 drivers/power/regulator/pfuze100.c
>>>>>
>>>>> diff --git a/drivers/power/regulator/Kconfig b/drivers/power/regulator/Kconfig
>>>>> index 6289b83..b854773 100644
>>>>> --- a/drivers/power/regulator/Kconfig
>>>>> +++ b/drivers/power/regulator/Kconfig
>>>>> @@ -16,6 +16,14 @@ config DM_REGULATOR
>>>>> for this purpose if PMIC I/O driver is implemented or dm_scan_fdt_node()
>>>>> otherwise. Detailed information can be found in the header file.
>>>>>
>>>>> +config DM_REGULATOR_PFUZE100
>>>>> + bool "Enable Driver Model for REGULATOR PFUZE100"
>>>>> + depends on DM_REGULATOR && DM_PMIC_PFUZE100
>>>>> + ---help---
>>>>> + This config enables implementation of driver-model regulator uclass
>>>>> + features for REGULATOR PFUZE100. The driver implements get/set api for:
>>>>> + value, enable and mode.
>>>>> +
>>>>> config DM_REGULATOR_MAX77686
>>>>> bool "Enable Driver Model for REGULATOR MAX77686"
>>>>> depends on DM_REGULATOR && DM_PMIC_MAX77686
>>>>> diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
>>>>> index 96aa624..9f8f17b 100644
>>>>> --- a/drivers/power/regulator/Makefile
>>>>> +++ b/drivers/power/regulator/Makefile
>>>>> @@ -7,5 +7,6 @@
>>>>>
>>>>> obj-$(CONFIG_DM_REGULATOR) += regulator-uclass.o
>>>>> obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
>>>>> +obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
>>>>> obj-$(CONFIG_DM_REGULATOR_FIXED) += fixed.o
>>>>> obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
>>>>> diff --git a/drivers/power/regulator/pfuze100.c b/drivers/power/regulator/pfuze100.c
>>>>> new file mode 100644
>>>>> index 0000000..6c513e9
>>>>> --- /dev/null
>>>>> +++ b/drivers/power/regulator/pfuze100.c
>>>>> @@ -0,0 +1,596 @@
>>>>> +#include <common.h>
>>>>> +#include <fdtdec.h>
>>>>> +#include <errno.h>
>>>>> +#include <dm.h>
>>>>> +#include <i2c.h>
>>>>> +#include <power/pmic.h>
>>>>> +#include <power/regulator.h>
>>>>> +#include <power/pfuze100_pmic.h>
>>>>> +
>>>>> +/**
>>>>> + * struct pfuze100_regulator_desc - regulator descriptor
>>>>> + *
>>>>> + * @name: Identify name for the regulator.
>>>>> + * @type: Indicates the regulator type.
>>>>> + * @uV_step: Voltage increase for each selector.
>>>>> + * @vsel_reg: Register for adjust regulator voltage for normal.
>>>>> + * @vsel_mask: Mask bit for setting regulator voltage for normal.
>>>>> + * @stby_reg: Register for adjust regulator voltage for standby.
>>>>> + * @stby_mask: Mask bit for setting regulator voltage for standby.
>>>>> + * @volt_table: Voltage mapping table (if table based mapping).
>>>>> + * @voltage: Current voltage for REGULATOR_TYPE_FIXED type regulator.
>>>>> + */
>>>>> +struct pfuze100_regulator_desc {
>>>>> + char *name;
>>>>> + enum regulator_type type;
>>>>> + unsigned int uV_step;
>>>>> + unsigned int vsel_reg;
>>>>> + unsigned int vsel_mask;
>>>>> + unsigned int stby_reg;
>>>>> + unsigned int stby_mask;
>>>>> + unsigned int *volt_table;
>>>>> + unsigned int voltage;
>>>>> +};
>>>>> +
>>>>> +#define PFUZE100_FIXED_REG(_name, base, vol) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_FIXED, \
>>>>> + .voltage = (vol), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SW_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x3F, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x3F, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SWB_REG(_name, base, mask, step, voltages) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = (mask), \
>>>>> + .volt_table = (voltages), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_SNVS_REG(_name, base, mask, voltages) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_OTHER, \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = (mask), \
>>>>> + .volt_table = (voltages), \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE100_VGEN_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_LDO, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = 0xF, \
>>>>> + .stby_reg = (base), \
>>>>> + .stby_mask = 0x20, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_VCC_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_LDO, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base), \
>>>>> + .vsel_mask = 0x3, \
>>>>> + .stby_reg = (base), \
>>>>> + .stby_mask = 0x20, \
>>>>> +}
>>>>> +
>>>>> +#define PFUZE3000_SW1_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x1F, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x1F, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_SW2_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0x7, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0x7, \
>>>>> + }
>>>>> +
>>>>> +#define PFUZE3000_SW3_REG(_name, base, step) \
>>>>> + { \
>>>>> + .name = #_name, \
>>>>> + .type = REGULATOR_TYPE_BUCK, \
>>>>> + .uV_step = (step), \
>>>>> + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \
>>>>> + .vsel_mask = 0xF, \
>>>>> + .stby_reg = (base) + PFUZE100_STBY_OFFSET, \
>>>>> + .stby_mask = 0xF, \
>>>>> + }
>>>>> +
>>>>> +static unsigned int pfuze100_swbst[] = {
>>>>> + 5000000, 5050000, 5100000, 5150000
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze100_vsnvs[] = {
>>>>> + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, -1
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze3000_vsnvs[] = {
>>>>> + -1, -1, -1, -1, -1, -1, 3000000, -1
>>>>> +};
>>>>> +
>>>>> +static unsigned int pfuze3000_sw2lo[] = {
>>>>> + 1500000, 1550000, 1600000, 1650000, 1700000, 1750000, 1800000, 1850000
>>>>> +};
>>>>> +
>>>>> +/* PFUZE100 */
>>>>> +static struct pfuze100_regulator_desc pfuze100_regulators[] = {
>>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw1c, PFUZE100_SW1CVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw4, PFUZE100_SW4VOL, 25000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +/* PFUZE200 */
>>>>> +static struct pfuze100_regulator_desc pfuze200_regulators[] = {
>>>>> + PFUZE100_SW_REG(sw1ab, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw2, PFUZE100_SW2VOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3a, PFUZE100_SW3AVOL, 25000),
>>>>> + PFUZE100_SW_REG(sw3b, PFUZE100_SW3BVOL, 25000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vgen1, PFUZE100_VGEN1VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE100_VGEN_REG(vgen3, PFUZE100_VGEN3VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen4, PFUZE100_VGEN4VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen5, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vgen6, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +/* PFUZE3000 */
>>>>> +static struct pfuze100_regulator_desc pfuze3000_regulators[] = {
>>>>> + PFUZE3000_SW1_REG(sw1a, PFUZE100_SW1ABVOL, 25000),
>>>>> + PFUZE3000_SW1_REG(sw1b, PFUZE100_SW1CVOL, 25000),
>>>>> + PFUZE100_SWB_REG(sw2, PFUZE100_SW2VOL, 0x7, 50000, pfuze3000_sw2lo),
>>>>> + PFUZE3000_SW3_REG(sw3, PFUZE100_SW3AVOL, 50000),
>>>>> + PFUZE100_SWB_REG(swbst, PFUZE100_SWBSTCON1, 0x3, 50000, pfuze100_swbst),
>>>>> + PFUZE100_SNVS_REG(vsnvs, PFUZE100_VSNVSVOL, 0x7, pfuze3000_vsnvs),
>>>>> + PFUZE100_FIXED_REG(vrefddr, PFUZE100_VREFDDRCON, 750000),
>>>>> + PFUZE100_VGEN_REG(vldo1, PFUZE100_VGEN1VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vldo2, PFUZE100_VGEN2VOL, 50000),
>>>>> + PFUZE3000_VCC_REG(vccsd, PFUZE100_VGEN3VOL, 150000),
>>>>> + PFUZE3000_VCC_REG(v33, PFUZE100_VGEN4VOL, 150000),
>>>>> + PFUZE100_VGEN_REG(vldo3, PFUZE100_VGEN5VOL, 100000),
>>>>> + PFUZE100_VGEN_REG(vldo4, PFUZE100_VGEN6VOL, 100000),
>>>>> +};
>>>>> +
>>>>> +#define MODE(_id, _val, _name) { \
>>>>> + .id = _id, \
>>>>> + .register_value = _val, \
>>>>> + .name = _name, \
>>>>> +}
>>>>> +
>>>>> +/* SWx Buck regulator mode */
>>>>> +static struct dm_regulator_mode pfuze_sw_modes[] = {
>>>>> + MODE(OFF_OFF, OFF_OFF, "OFF_OFF"),
>>>>> + MODE(PWM_OFF, PWM_OFF, "PWM_OFF"),
>>>>> + MODE(PFM_OFF, PFM_OFF, "PFM_OFF"),
>>>>> + MODE(APS_OFF, APS_OFF, "APS_OFF"),
>>>>> + MODE(PWM_PWM, PWM_PWM, "PWM_PWM"),
>>>>> + MODE(PWM_APS, PWM_APS, "PWM_APS"),
>>>>> + MODE(APS_APS, APS_APS, "APS_APS"),
>>>>> + MODE(APS_PFM, APS_PFM, "APS_PFM"),
>>>>> + MODE(PWM_PFM, PWM_PFM, "PWM_PFM"),
>>>>> +};
>>>>> +
>>>>> +/* Boost Buck regulator mode for normal operation */
>>>>> +static struct dm_regulator_mode pfuze_swbst_modes[] = {
>>>>> + MODE(SWBST_MODE_OFF, SWBST_MODE_OFF , "SWBST_MODE_OFF"),
>>>>> + MODE(SWBST_MODE_PFM, SWBST_MODE_PFM, "SWBST_MODE_PFM"),
>>>>> + MODE(SWBST_MODE_AUTO, SWBST_MODE_AUTO, "SWBST_MODE_AUTO"),
>>>>> + MODE(SWBST_MODE_APS, SWBST_MODE_APS, "SWBST_MODE_APS"),
>>>>> +};
>>>>> +
>>>>> +/* VGENx LDO regulator mode for normal operation */
>>>>> +static struct dm_regulator_mode pfuze_ldo_modes[] = {
>>>>> + MODE(LDO_MODE_OFF, LDO_MODE_OFF, "LDO_MODE_OFF"),
>>>>> + MODE(LDO_MODE_ON, LDO_MODE_ON, "LDO_MODE_ON"),
>>>>> +};
>>>>> +
>>>>> +static struct pfuze100_regulator_desc *se_desc(struct pfuze100_regulator_desc *desc,
>>>>> + int size,
>>>>> + const char *name)
>>>>> +{
>>>>> + int i;
>>>>
>>>>blank line between declarations and rest - please fix global
>>>
>>>Will fix in V2.
>>>
>>>>
>>>>> + for (i = 0; i < size; desc++) {
>>>>> + if (!strcmp(desc->name, name))
>>>>> + return desc;
>>>>> + continue;
>>>>> + }
>>>>> +
>>>>> + return NULL;
>>>>> +}
>>>>> +
>>>>> +static int pfuze100_regulator_probe(struct udevice *dev)
>>>>> +{
>>>>> + struct dm_regulator_uclass_platdata *uc_pdata;
>>>>> + struct pfuze100_regulator_desc **desc = NULL;
>>>>
>>>>Can't this just be a single pointer?
>>
>> After a thought, a single pointer can not make it work.
>>
>> struct pfuze100_regulator_desc is for per regulator.
>> If use a single pointer, then "desc = dev_get_platdata(dev);" can not
>> change the platdata for each regulator. I need to use "struct xx **" to
>> reflect the change into platdata for each regulator.
>>
>> [...]
>>
>>
>
>I see that you a searching your table based the device name. Normally
>we name the regulators LDO1, LDO2 and use the number (1, 2) to find
>the right device. Can you please point me to your device tree
>contents?
I replied in v2 patch set. Still paste url here,
http://lxr.free-electrons.com/source/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
line from 208 to 306.
>
>You could make the platdata be something like
>
>struct pfuze_platdata {
> struct pfuze100_regulator_desc *desc;
>};
>
>I think the code would be clearer that way. You can assign to the desc
>member instead of a double pointer indirect.
Thanks. Will consider to use this way.
Regards,
Peng.
--
^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2015-08-04 13:16 UTC | newest]
Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-07-28 14:48 [U-Boot] [PATCH 0/5] Power: pfuze100: support driver model and regulator Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 1/5] power: pfuze100 correct SWBST macro definition Peng Fan
2015-08-02 22:30 ` Simon Glass
2015-07-28 14:48 ` [U-Boot] [PATCH 2/5] power: regulator use node name when no regulator-name Peng Fan
2015-08-02 22:31 ` Simon Glass
2015-08-03 0:23 ` Peng Fan
2015-08-03 15:00 ` Przemyslaw Marczak
2015-08-04 0:12 ` Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 3/5] power: pmic: pfuze100 support driver model Peng Fan
2015-08-02 22:31 ` Simon Glass
2015-08-03 15:01 ` Przemyslaw Marczak
2015-08-04 0:15 ` Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 4/5] power: regulator: add pfuze100 support Peng Fan
2015-08-02 22:30 ` Simon Glass
2015-08-03 0:38 ` Peng Fan
2015-08-04 2:08 ` Peng Fan
2015-08-04 12:46 ` Simon Glass
2015-08-04 13:16 ` Przemyslaw Marczak
2015-08-04 13:16 ` Peng Fan
2015-07-28 14:48 ` [U-Boot] [PATCH 5/5] fsl: common: pfuze: no use original pfuze code if DM_PMIC Peng Fan
2015-08-02 22:30 ` Simon Glass
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.