* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel, linux-kernel
Cc: kernel, maxime.coquelin, viresh.kumar, linux-pm, rjw, devicetree,
ajitpal.singh, Lee Jones
Hi Rafael,
Would you be kind enough to pick these 2 patches up please.
The have the required Acks.
Kind regards,
Lee
This is a re-write of the original submission, hence why the
change-log is omitted. Basically almost everything has changed.
We are now using the new OPP framework and generic bindings
written by Viresh.
There are 'ARM' patches in the set which are not necessarily
related to CPUFreq, but are required to get it to work. Anyone
who is not interested in general STi DT changes can safely
ignore these.
v5 => v6:
- Converted Kconfig and header comment to describe new driver
- Complete re-write, using new Generic OPP framework
- Supply description for "suitable for ALL versions" DEFINE
- Pedantically re-ordered the #include files
- Removed platform device registration in arch/arm/mach-sti
v4 => v5:
- Converted driver away from being a platform device
v1 => v2 => v3 => v4:
- Moot
Lee Jones (2):
cpufreq: st: Provide runtime initialised driver for ST's platforms
dt: cpufreq: st: Provide bindings for ST's CPUFreq implementation
.../devicetree/bindings/cpufreq/cpufreq-st.txt | 91 +++++++
drivers/cpufreq/Kconfig.arm | 10 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/sti-cpufreq.c | 294 +++++++++++++++++++++
4 files changed, 396 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
create mode 100644 drivers/cpufreq/sti-cpufreq.c
--
1.9.1
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel
Hi Rafael,
Would you be kind enough to pick these 2 patches up please.
The have the required Acks.
Kind regards,
Lee
This is a re-write of the original submission, hence why the
change-log is omitted. Basically almost everything has changed.
We are now using the new OPP framework and generic bindings
written by Viresh.
There are 'ARM' patches in the set which are not necessarily
related to CPUFreq, but are required to get it to work. Anyone
who is not interested in general STi DT changes can safely
ignore these.
v5 => v6:
- Converted Kconfig and header comment to describe new driver
- Complete re-write, using new Generic OPP framework
- Supply description for "suitable for ALL versions" DEFINE
- Pedantically re-ordered the #include files
- Removed platform device registration in arch/arm/mach-sti
v4 => v5:
- Converted driver away from being a platform device
v1 => v2 => v3 => v4:
- Moot
Lee Jones (2):
cpufreq: st: Provide runtime initialised driver for ST's platforms
dt: cpufreq: st: Provide bindings for ST's CPUFreq implementation
.../devicetree/bindings/cpufreq/cpufreq-st.txt | 91 +++++++
drivers/cpufreq/Kconfig.arm | 10 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/sti-cpufreq.c | 294 +++++++++++++++++++++
4 files changed, 396 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
create mode 100644 drivers/cpufreq/sti-cpufreq.c
--
1.9.1
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 1/2] cpufreq: st: Provide runtime initialised driver for ST's platforms
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel, linux-kernel
Cc: kernel, maxime.coquelin, viresh.kumar, linux-pm, rjw, devicetree,
ajitpal.singh, Lee Jones
The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree. This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/cpufreq/Kconfig.arm | 10 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/sti-cpufreq.c | 294 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 305 insertions(+)
create mode 100644 drivers/cpufreq/sti-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 1582c1c..2dfc327 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -216,6 +216,16 @@ config ARM_SPEAR_CPUFREQ
help
This adds the CPUFreq driver support for SPEAr SOCs.
+config ARM_STI_CPUFREQ
+ tristate "STi CPUFreq support"
+ depends on SOC_STIH407
+ help
+ This driver uses the generic OPP framework to match the running
+ platform with a predefined set of suitable values. If not provided
+ we will fall-back so safe-values contained in Device Tree. Enable
+ this config option if you wish to add CPUFreq support for STi based
+ SoCs.
+
config ARM_TEGRA20_CPUFREQ
bool "Tegra20 CPUFreq support"
depends on ARCH_TEGRA
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index c0af1a1..9e63fb1 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -73,6 +73,7 @@ obj-$(CONFIG_ARM_SA1100_CPUFREQ) += sa1100-cpufreq.o
obj-$(CONFIG_ARM_SA1110_CPUFREQ) += sa1110-cpufreq.o
obj-$(CONFIG_ARM_SCPI_CPUFREQ) += scpi-cpufreq.o
obj-$(CONFIG_ARM_SPEAR_CPUFREQ) += spear-cpufreq.o
+obj-$(CONFIG_ARM_STI_CPUFREQ) += sti-cpufreq.o
obj-$(CONFIG_ARM_TEGRA20_CPUFREQ) += tegra20-cpufreq.o
obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
diff --git a/drivers/cpufreq/sti-cpufreq.c b/drivers/cpufreq/sti-cpufreq.c
new file mode 100644
index 0000000..a9c659f
--- /dev/null
+++ b/drivers/cpufreq/sti-cpufreq.c
@@ -0,0 +1,294 @@
+/*
+ * Match running platform with pre-defined OPP values for CPUFreq
+ *
+ * Author: Ajit Pal Singh <ajitpal.singh@st.com>
+ * Lee Jones <lee.jones@linaro.org>
+ *
+ * Copyright (C) 2015 STMicroelectronics (R&D) Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#include <linux/cpu.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_opp.h>
+#include <linux/regmap.h>
+
+#define VERSION_ELEMENTS 3
+#define MAX_PCODE_NAME_LEN 7
+
+#define VERSION_SHIFT 28
+#define HW_INFO_INDEX 1
+#define MAJOR_ID_INDEX 1
+#define MINOR_ID_INDEX 2
+
+/*
+ * Only match on "suitable for ALL versions" entries
+ *
+ * This will be used with the BIT() macro. It sets the
+ * top bit of a 32bit value and is equal to 0x80000000.
+ */
+#define DEFAULT_VERSION 31
+
+enum {
+ PCODE = 0,
+ SUBSTRATE,
+ DVFS_MAX_REGFIELDS,
+};
+
+/**
+ * ST CPUFreq Driver Data
+ *
+ * @cpu_node CPU's OF node
+ * @syscfg_eng Engineering Syscon register map
+ * @regmap Syscon register map
+ */
+static struct sti_cpufreq_ddata {
+ struct device *cpu;
+ struct regmap *syscfg_eng;
+ struct regmap *syscfg;
+} ddata;
+
+static int sti_cpufreq_fetch_major(void) {
+ struct device_node *np = ddata.cpu->of_node;
+ struct device *dev = ddata.cpu;
+ unsigned int major_offset;
+ unsigned int socid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg",
+ MAJOR_ID_INDEX, &major_offset);
+ if (ret) {
+ dev_err(dev, "No major number offset provided in %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg, major_offset, &socid);
+ if (ret) {
+ dev_err(dev, "Failed to read major number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return ((socid >> VERSION_SHIFT) & 0xf) + 1;
+}
+
+static int sti_cpufreq_fetch_minor(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ unsigned int minor_offset;
+ unsigned int minid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ MINOR_ID_INDEX, &minor_offset);
+ if (ret) {
+ dev_err(dev,
+ "No minor number offset provided %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg_eng, minor_offset, &minid);
+ if (ret) {
+ dev_err(dev,
+ "Failed to read the minor number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return minid & 0xf;
+}
+
+static int sti_cpufreq_fetch_regmap_field(const struct reg_field *reg_fields,
+ int hw_info_offset, int field)
+{
+ struct regmap_field *regmap_field;
+ struct reg_field reg_field = reg_fields[field];
+ struct device *dev = ddata.cpu;
+ unsigned int value;
+ int ret;
+
+ reg_field.reg = hw_info_offset;
+ regmap_field = devm_regmap_field_alloc(dev,
+ ddata.syscfg_eng,
+ reg_field);
+ if (IS_ERR(regmap_field)) {
+ dev_err(dev, "Failed to allocate reg field\n");
+ return PTR_ERR(regmap_field);
+ }
+
+ ret = regmap_field_read(regmap_field, &value);
+ if (ret) {
+ dev_err(dev, "Failed to read %s code\n",
+ field ? "SUBSTRATE" : "PCODE");
+ return ret;
+ }
+
+ return value;
+}
+
+static const struct reg_field sti_stih407_dvfs_regfields[DVFS_MAX_REGFIELDS] = {
+ [PCODE] = REG_FIELD(0, 16, 19),
+ [SUBSTRATE] = REG_FIELD(0, 0, 2),
+};
+
+static const struct reg_field *sti_cpufreq_match(void)
+{
+ if (of_machine_is_compatible("st,stih407") ||
+ of_machine_is_compatible("st,stih410"))
+ return sti_stih407_dvfs_regfields;
+
+ return NULL;
+}
+
+static int sti_cpufreq_set_opp_info(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ const struct reg_field *reg_fields;
+ unsigned int hw_info_offset;
+ unsigned int version[VERSION_ELEMENTS];
+ int pcode, substrate, major, minor;
+ int ret;
+ char name[MAX_PCODE_NAME_LEN];
+
+ reg_fields = sti_cpufreq_match();
+ if (!reg_fields) {
+ dev_err(dev, "This SoC doesn't support voltage scaling");
+ return -ENODEV;
+ }
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ HW_INFO_INDEX, &hw_info_offset);
+ if (ret) {
+ dev_warn(dev, "Failed to read HW info offset from DT\n");
+ substrate = DEFAULT_VERSION;
+ pcode = 0;
+ goto use_defaults;
+ }
+
+ pcode = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ PCODE);
+ if (pcode < 0) {
+ dev_warn(dev, "Failed to obtain process code\n");
+ /* Use default pcode */
+ pcode = 0;
+ }
+
+ substrate = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ SUBSTRATE);
+ if (substrate) {
+ dev_warn(dev, "Failed to obtain substrate code\n");
+ /* Use default substrate */
+ substrate = DEFAULT_VERSION;
+ }
+
+use_defaults:
+ major = sti_cpufreq_fetch_major();
+ if (major < 0) {
+ dev_err(dev, "Failed to obtain major version\n");
+ /* Use default major number */
+ major = DEFAULT_VERSION;
+ }
+
+ minor = sti_cpufreq_fetch_minor();
+ if (minor < 0) {
+ dev_err(dev, "Failed to obtain minor version\n");
+ /* Use default minor number */
+ minor = DEFAULT_VERSION;
+ }
+
+ snprintf(name, MAX_PCODE_NAME_LEN, "pcode%d", pcode);
+
+ ret = dev_pm_opp_set_prop_name(dev, name);
+ if (ret) {
+ dev_err(dev, "Failed to set prop name\n");
+ return ret;
+ }
+
+ version[0] = BIT(major);
+ version[1] = BIT(minor);
+ version[2] = BIT(substrate);
+
+ ret = dev_pm_opp_set_supported_hw(dev, version, VERSION_ELEMENTS);
+ if (ret) {
+ dev_err(dev, "Failed to set supported hardware\n");
+ return ret;
+ }
+
+ dev_dbg(dev, "pcode: %d major: %d minor: %d substrate: %d\n",
+ pcode, major, minor, substrate);
+ dev_dbg(dev, "version[0]: %x version[1]: %x version[2]: %x\n",
+ version[0], version[1], version[2]);
+
+ return 0;
+}
+
+static int sti_cpufreq_fetch_syscon_regsiters(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+
+ ddata.syscfg = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(ddata.syscfg)) {
+ dev_err(dev, "\"st,syscfg\" not supplied\n");
+ return PTR_ERR(ddata.syscfg);
+ }
+
+ ddata.syscfg_eng = syscon_regmap_lookup_by_phandle(np, "st,syscfg-eng");
+ if (IS_ERR(ddata.syscfg_eng)) {
+ dev_err(dev, "\"st,syscfg-eng\" not supplied\n");
+ return PTR_ERR(ddata.syscfg_eng);
+ }
+
+ return 0;
+}
+
+static int sti_cpufreq_init(void)
+{
+ int ret;
+
+ ddata.cpu = get_cpu_device(0);
+ if (!ddata.cpu) {
+ dev_err(ddata.cpu, "Failed to get device for CPU0\n");
+ goto skip_voltage_scaling;
+ }
+
+ if (!of_get_property(ddata.cpu->of_node, "operating-points-v2", NULL)) {
+ dev_err(ddata.cpu, "OPP-v2 not supported\n");
+ goto skip_voltage_scaling;
+ }
+
+ ret = sti_cpufreq_fetch_syscon_regsiters();
+ if (ret)
+ goto skip_voltage_scaling;
+
+ ret = sti_cpufreq_set_opp_info();
+ if (!ret)
+ goto register_cpufreq_dt;
+
+skip_voltage_scaling:
+ dev_err(ddata.cpu, "Not doing voltage scaling\n");
+
+register_cpufreq_dt:
+ platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
+
+ return 0;
+}
+module_init(sti_cpufreq_init);
+
+MODULE_DESCRIPTION("STMicroelectronics CPUFreq/OPP driver");
+MODULE_AUTHOR("Ajitpal Singh <ajitpal.singh@st.com>");
+MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PICKME 1/2] cpufreq: st: Provide runtime initialised driver for ST's platforms
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: kernel-F5mvAk5X5gdBDgjK7y7TUQ, maxime.coquelin-qxv4g6HH51o,
viresh.kumar-QSEj5FYQhm4dnm+yROfE0A,
linux-pm-u79uwXL29TY76Z2rM5mHXA, rjw-LthD3rsA81gm4RdzfppkhA,
devicetree-u79uwXL29TY76Z2rM5mHXA, ajitpal.singh-qxv4g6HH51o,
Lee Jones
The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree. This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.
Acked-by: Viresh Kumar <viresh.kumar-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
drivers/cpufreq/Kconfig.arm | 10 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/sti-cpufreq.c | 294 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 305 insertions(+)
create mode 100644 drivers/cpufreq/sti-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 1582c1c..2dfc327 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -216,6 +216,16 @@ config ARM_SPEAR_CPUFREQ
help
This adds the CPUFreq driver support for SPEAr SOCs.
+config ARM_STI_CPUFREQ
+ tristate "STi CPUFreq support"
+ depends on SOC_STIH407
+ help
+ This driver uses the generic OPP framework to match the running
+ platform with a predefined set of suitable values. If not provided
+ we will fall-back so safe-values contained in Device Tree. Enable
+ this config option if you wish to add CPUFreq support for STi based
+ SoCs.
+
config ARM_TEGRA20_CPUFREQ
bool "Tegra20 CPUFreq support"
depends on ARCH_TEGRA
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index c0af1a1..9e63fb1 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -73,6 +73,7 @@ obj-$(CONFIG_ARM_SA1100_CPUFREQ) += sa1100-cpufreq.o
obj-$(CONFIG_ARM_SA1110_CPUFREQ) += sa1110-cpufreq.o
obj-$(CONFIG_ARM_SCPI_CPUFREQ) += scpi-cpufreq.o
obj-$(CONFIG_ARM_SPEAR_CPUFREQ) += spear-cpufreq.o
+obj-$(CONFIG_ARM_STI_CPUFREQ) += sti-cpufreq.o
obj-$(CONFIG_ARM_TEGRA20_CPUFREQ) += tegra20-cpufreq.o
obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
diff --git a/drivers/cpufreq/sti-cpufreq.c b/drivers/cpufreq/sti-cpufreq.c
new file mode 100644
index 0000000..a9c659f
--- /dev/null
+++ b/drivers/cpufreq/sti-cpufreq.c
@@ -0,0 +1,294 @@
+/*
+ * Match running platform with pre-defined OPP values for CPUFreq
+ *
+ * Author: Ajit Pal Singh <ajitpal.singh-qxv4g6HH51o@public.gmane.org>
+ * Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *
+ * Copyright (C) 2015 STMicroelectronics (R&D) Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#include <linux/cpu.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_opp.h>
+#include <linux/regmap.h>
+
+#define VERSION_ELEMENTS 3
+#define MAX_PCODE_NAME_LEN 7
+
+#define VERSION_SHIFT 28
+#define HW_INFO_INDEX 1
+#define MAJOR_ID_INDEX 1
+#define MINOR_ID_INDEX 2
+
+/*
+ * Only match on "suitable for ALL versions" entries
+ *
+ * This will be used with the BIT() macro. It sets the
+ * top bit of a 32bit value and is equal to 0x80000000.
+ */
+#define DEFAULT_VERSION 31
+
+enum {
+ PCODE = 0,
+ SUBSTRATE,
+ DVFS_MAX_REGFIELDS,
+};
+
+/**
+ * ST CPUFreq Driver Data
+ *
+ * @cpu_node CPU's OF node
+ * @syscfg_eng Engineering Syscon register map
+ * @regmap Syscon register map
+ */
+static struct sti_cpufreq_ddata {
+ struct device *cpu;
+ struct regmap *syscfg_eng;
+ struct regmap *syscfg;
+} ddata;
+
+static int sti_cpufreq_fetch_major(void) {
+ struct device_node *np = ddata.cpu->of_node;
+ struct device *dev = ddata.cpu;
+ unsigned int major_offset;
+ unsigned int socid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg",
+ MAJOR_ID_INDEX, &major_offset);
+ if (ret) {
+ dev_err(dev, "No major number offset provided in %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg, major_offset, &socid);
+ if (ret) {
+ dev_err(dev, "Failed to read major number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return ((socid >> VERSION_SHIFT) & 0xf) + 1;
+}
+
+static int sti_cpufreq_fetch_minor(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ unsigned int minor_offset;
+ unsigned int minid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ MINOR_ID_INDEX, &minor_offset);
+ if (ret) {
+ dev_err(dev,
+ "No minor number offset provided %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg_eng, minor_offset, &minid);
+ if (ret) {
+ dev_err(dev,
+ "Failed to read the minor number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return minid & 0xf;
+}
+
+static int sti_cpufreq_fetch_regmap_field(const struct reg_field *reg_fields,
+ int hw_info_offset, int field)
+{
+ struct regmap_field *regmap_field;
+ struct reg_field reg_field = reg_fields[field];
+ struct device *dev = ddata.cpu;
+ unsigned int value;
+ int ret;
+
+ reg_field.reg = hw_info_offset;
+ regmap_field = devm_regmap_field_alloc(dev,
+ ddata.syscfg_eng,
+ reg_field);
+ if (IS_ERR(regmap_field)) {
+ dev_err(dev, "Failed to allocate reg field\n");
+ return PTR_ERR(regmap_field);
+ }
+
+ ret = regmap_field_read(regmap_field, &value);
+ if (ret) {
+ dev_err(dev, "Failed to read %s code\n",
+ field ? "SUBSTRATE" : "PCODE");
+ return ret;
+ }
+
+ return value;
+}
+
+static const struct reg_field sti_stih407_dvfs_regfields[DVFS_MAX_REGFIELDS] = {
+ [PCODE] = REG_FIELD(0, 16, 19),
+ [SUBSTRATE] = REG_FIELD(0, 0, 2),
+};
+
+static const struct reg_field *sti_cpufreq_match(void)
+{
+ if (of_machine_is_compatible("st,stih407") ||
+ of_machine_is_compatible("st,stih410"))
+ return sti_stih407_dvfs_regfields;
+
+ return NULL;
+}
+
+static int sti_cpufreq_set_opp_info(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ const struct reg_field *reg_fields;
+ unsigned int hw_info_offset;
+ unsigned int version[VERSION_ELEMENTS];
+ int pcode, substrate, major, minor;
+ int ret;
+ char name[MAX_PCODE_NAME_LEN];
+
+ reg_fields = sti_cpufreq_match();
+ if (!reg_fields) {
+ dev_err(dev, "This SoC doesn't support voltage scaling");
+ return -ENODEV;
+ }
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ HW_INFO_INDEX, &hw_info_offset);
+ if (ret) {
+ dev_warn(dev, "Failed to read HW info offset from DT\n");
+ substrate = DEFAULT_VERSION;
+ pcode = 0;
+ goto use_defaults;
+ }
+
+ pcode = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ PCODE);
+ if (pcode < 0) {
+ dev_warn(dev, "Failed to obtain process code\n");
+ /* Use default pcode */
+ pcode = 0;
+ }
+
+ substrate = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ SUBSTRATE);
+ if (substrate) {
+ dev_warn(dev, "Failed to obtain substrate code\n");
+ /* Use default substrate */
+ substrate = DEFAULT_VERSION;
+ }
+
+use_defaults:
+ major = sti_cpufreq_fetch_major();
+ if (major < 0) {
+ dev_err(dev, "Failed to obtain major version\n");
+ /* Use default major number */
+ major = DEFAULT_VERSION;
+ }
+
+ minor = sti_cpufreq_fetch_minor();
+ if (minor < 0) {
+ dev_err(dev, "Failed to obtain minor version\n");
+ /* Use default minor number */
+ minor = DEFAULT_VERSION;
+ }
+
+ snprintf(name, MAX_PCODE_NAME_LEN, "pcode%d", pcode);
+
+ ret = dev_pm_opp_set_prop_name(dev, name);
+ if (ret) {
+ dev_err(dev, "Failed to set prop name\n");
+ return ret;
+ }
+
+ version[0] = BIT(major);
+ version[1] = BIT(minor);
+ version[2] = BIT(substrate);
+
+ ret = dev_pm_opp_set_supported_hw(dev, version, VERSION_ELEMENTS);
+ if (ret) {
+ dev_err(dev, "Failed to set supported hardware\n");
+ return ret;
+ }
+
+ dev_dbg(dev, "pcode: %d major: %d minor: %d substrate: %d\n",
+ pcode, major, minor, substrate);
+ dev_dbg(dev, "version[0]: %x version[1]: %x version[2]: %x\n",
+ version[0], version[1], version[2]);
+
+ return 0;
+}
+
+static int sti_cpufreq_fetch_syscon_regsiters(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+
+ ddata.syscfg = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(ddata.syscfg)) {
+ dev_err(dev, "\"st,syscfg\" not supplied\n");
+ return PTR_ERR(ddata.syscfg);
+ }
+
+ ddata.syscfg_eng = syscon_regmap_lookup_by_phandle(np, "st,syscfg-eng");
+ if (IS_ERR(ddata.syscfg_eng)) {
+ dev_err(dev, "\"st,syscfg-eng\" not supplied\n");
+ return PTR_ERR(ddata.syscfg_eng);
+ }
+
+ return 0;
+}
+
+static int sti_cpufreq_init(void)
+{
+ int ret;
+
+ ddata.cpu = get_cpu_device(0);
+ if (!ddata.cpu) {
+ dev_err(ddata.cpu, "Failed to get device for CPU0\n");
+ goto skip_voltage_scaling;
+ }
+
+ if (!of_get_property(ddata.cpu->of_node, "operating-points-v2", NULL)) {
+ dev_err(ddata.cpu, "OPP-v2 not supported\n");
+ goto skip_voltage_scaling;
+ }
+
+ ret = sti_cpufreq_fetch_syscon_regsiters();
+ if (ret)
+ goto skip_voltage_scaling;
+
+ ret = sti_cpufreq_set_opp_info();
+ if (!ret)
+ goto register_cpufreq_dt;
+
+skip_voltage_scaling:
+ dev_err(ddata.cpu, "Not doing voltage scaling\n");
+
+register_cpufreq_dt:
+ platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
+
+ return 0;
+}
+module_init(sti_cpufreq_init);
+
+MODULE_DESCRIPTION("STMicroelectronics CPUFreq/OPP driver");
+MODULE_AUTHOR("Ajitpal Singh <ajitpal.singh-qxv4g6HH51o@public.gmane.org>");
+MODULE_AUTHOR("Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PICKME 1/2] cpufreq: st: Provide runtime initialised driver for ST's platforms
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel
The bootloader is charged with the responsibility to provide platform
specific Dynamic Voltage and Frequency Scaling (DVFS) information via
Device Tree. This driver takes the supplied configuration and
registers it with the new generic OPP framework, to then be used with
CPUFreq.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/cpufreq/Kconfig.arm | 10 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/sti-cpufreq.c | 294 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 305 insertions(+)
create mode 100644 drivers/cpufreq/sti-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 1582c1c..2dfc327 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -216,6 +216,16 @@ config ARM_SPEAR_CPUFREQ
help
This adds the CPUFreq driver support for SPEAr SOCs.
+config ARM_STI_CPUFREQ
+ tristate "STi CPUFreq support"
+ depends on SOC_STIH407
+ help
+ This driver uses the generic OPP framework to match the running
+ platform with a predefined set of suitable values. If not provided
+ we will fall-back so safe-values contained in Device Tree. Enable
+ this config option if you wish to add CPUFreq support for STi based
+ SoCs.
+
config ARM_TEGRA20_CPUFREQ
bool "Tegra20 CPUFreq support"
depends on ARCH_TEGRA
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index c0af1a1..9e63fb1 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -73,6 +73,7 @@ obj-$(CONFIG_ARM_SA1100_CPUFREQ) += sa1100-cpufreq.o
obj-$(CONFIG_ARM_SA1110_CPUFREQ) += sa1110-cpufreq.o
obj-$(CONFIG_ARM_SCPI_CPUFREQ) += scpi-cpufreq.o
obj-$(CONFIG_ARM_SPEAR_CPUFREQ) += spear-cpufreq.o
+obj-$(CONFIG_ARM_STI_CPUFREQ) += sti-cpufreq.o
obj-$(CONFIG_ARM_TEGRA20_CPUFREQ) += tegra20-cpufreq.o
obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
diff --git a/drivers/cpufreq/sti-cpufreq.c b/drivers/cpufreq/sti-cpufreq.c
new file mode 100644
index 0000000..a9c659f
--- /dev/null
+++ b/drivers/cpufreq/sti-cpufreq.c
@@ -0,0 +1,294 @@
+/*
+ * Match running platform with pre-defined OPP values for CPUFreq
+ *
+ * Author: Ajit Pal Singh <ajitpal.singh@st.com>
+ * Lee Jones <lee.jones@linaro.org>
+ *
+ * Copyright (C) 2015 STMicroelectronics (R&D) Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#include <linux/cpu.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_opp.h>
+#include <linux/regmap.h>
+
+#define VERSION_ELEMENTS 3
+#define MAX_PCODE_NAME_LEN 7
+
+#define VERSION_SHIFT 28
+#define HW_INFO_INDEX 1
+#define MAJOR_ID_INDEX 1
+#define MINOR_ID_INDEX 2
+
+/*
+ * Only match on "suitable for ALL versions" entries
+ *
+ * This will be used with the BIT() macro. It sets the
+ * top bit of a 32bit value and is equal to 0x80000000.
+ */
+#define DEFAULT_VERSION 31
+
+enum {
+ PCODE = 0,
+ SUBSTRATE,
+ DVFS_MAX_REGFIELDS,
+};
+
+/**
+ * ST CPUFreq Driver Data
+ *
+ * @cpu_node CPU's OF node
+ * @syscfg_eng Engineering Syscon register map
+ * @regmap Syscon register map
+ */
+static struct sti_cpufreq_ddata {
+ struct device *cpu;
+ struct regmap *syscfg_eng;
+ struct regmap *syscfg;
+} ddata;
+
+static int sti_cpufreq_fetch_major(void) {
+ struct device_node *np = ddata.cpu->of_node;
+ struct device *dev = ddata.cpu;
+ unsigned int major_offset;
+ unsigned int socid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg",
+ MAJOR_ID_INDEX, &major_offset);
+ if (ret) {
+ dev_err(dev, "No major number offset provided in %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg, major_offset, &socid);
+ if (ret) {
+ dev_err(dev, "Failed to read major number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return ((socid >> VERSION_SHIFT) & 0xf) + 1;
+}
+
+static int sti_cpufreq_fetch_minor(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ unsigned int minor_offset;
+ unsigned int minid;
+ int ret;
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ MINOR_ID_INDEX, &minor_offset);
+ if (ret) {
+ dev_err(dev,
+ "No minor number offset provided %s [%d]\n",
+ np->full_name, ret);
+ return ret;
+ }
+
+ ret = regmap_read(ddata.syscfg_eng, minor_offset, &minid);
+ if (ret) {
+ dev_err(dev,
+ "Failed to read the minor number from syscon [%d]\n",
+ ret);
+ return ret;
+ }
+
+ return minid & 0xf;
+}
+
+static int sti_cpufreq_fetch_regmap_field(const struct reg_field *reg_fields,
+ int hw_info_offset, int field)
+{
+ struct regmap_field *regmap_field;
+ struct reg_field reg_field = reg_fields[field];
+ struct device *dev = ddata.cpu;
+ unsigned int value;
+ int ret;
+
+ reg_field.reg = hw_info_offset;
+ regmap_field = devm_regmap_field_alloc(dev,
+ ddata.syscfg_eng,
+ reg_field);
+ if (IS_ERR(regmap_field)) {
+ dev_err(dev, "Failed to allocate reg field\n");
+ return PTR_ERR(regmap_field);
+ }
+
+ ret = regmap_field_read(regmap_field, &value);
+ if (ret) {
+ dev_err(dev, "Failed to read %s code\n",
+ field ? "SUBSTRATE" : "PCODE");
+ return ret;
+ }
+
+ return value;
+}
+
+static const struct reg_field sti_stih407_dvfs_regfields[DVFS_MAX_REGFIELDS] = {
+ [PCODE] = REG_FIELD(0, 16, 19),
+ [SUBSTRATE] = REG_FIELD(0, 0, 2),
+};
+
+static const struct reg_field *sti_cpufreq_match(void)
+{
+ if (of_machine_is_compatible("st,stih407") ||
+ of_machine_is_compatible("st,stih410"))
+ return sti_stih407_dvfs_regfields;
+
+ return NULL;
+}
+
+static int sti_cpufreq_set_opp_info(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+ const struct reg_field *reg_fields;
+ unsigned int hw_info_offset;
+ unsigned int version[VERSION_ELEMENTS];
+ int pcode, substrate, major, minor;
+ int ret;
+ char name[MAX_PCODE_NAME_LEN];
+
+ reg_fields = sti_cpufreq_match();
+ if (!reg_fields) {
+ dev_err(dev, "This SoC doesn't support voltage scaling");
+ return -ENODEV;
+ }
+
+ ret = of_property_read_u32_index(np, "st,syscfg-eng",
+ HW_INFO_INDEX, &hw_info_offset);
+ if (ret) {
+ dev_warn(dev, "Failed to read HW info offset from DT\n");
+ substrate = DEFAULT_VERSION;
+ pcode = 0;
+ goto use_defaults;
+ }
+
+ pcode = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ PCODE);
+ if (pcode < 0) {
+ dev_warn(dev, "Failed to obtain process code\n");
+ /* Use default pcode */
+ pcode = 0;
+ }
+
+ substrate = sti_cpufreq_fetch_regmap_field(reg_fields,
+ hw_info_offset,
+ SUBSTRATE);
+ if (substrate) {
+ dev_warn(dev, "Failed to obtain substrate code\n");
+ /* Use default substrate */
+ substrate = DEFAULT_VERSION;
+ }
+
+use_defaults:
+ major = sti_cpufreq_fetch_major();
+ if (major < 0) {
+ dev_err(dev, "Failed to obtain major version\n");
+ /* Use default major number */
+ major = DEFAULT_VERSION;
+ }
+
+ minor = sti_cpufreq_fetch_minor();
+ if (minor < 0) {
+ dev_err(dev, "Failed to obtain minor version\n");
+ /* Use default minor number */
+ minor = DEFAULT_VERSION;
+ }
+
+ snprintf(name, MAX_PCODE_NAME_LEN, "pcode%d", pcode);
+
+ ret = dev_pm_opp_set_prop_name(dev, name);
+ if (ret) {
+ dev_err(dev, "Failed to set prop name\n");
+ return ret;
+ }
+
+ version[0] = BIT(major);
+ version[1] = BIT(minor);
+ version[2] = BIT(substrate);
+
+ ret = dev_pm_opp_set_supported_hw(dev, version, VERSION_ELEMENTS);
+ if (ret) {
+ dev_err(dev, "Failed to set supported hardware\n");
+ return ret;
+ }
+
+ dev_dbg(dev, "pcode: %d major: %d minor: %d substrate: %d\n",
+ pcode, major, minor, substrate);
+ dev_dbg(dev, "version[0]: %x version[1]: %x version[2]: %x\n",
+ version[0], version[1], version[2]);
+
+ return 0;
+}
+
+static int sti_cpufreq_fetch_syscon_regsiters(void)
+{
+ struct device *dev = ddata.cpu;
+ struct device_node *np = dev->of_node;
+
+ ddata.syscfg = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(ddata.syscfg)) {
+ dev_err(dev, "\"st,syscfg\" not supplied\n");
+ return PTR_ERR(ddata.syscfg);
+ }
+
+ ddata.syscfg_eng = syscon_regmap_lookup_by_phandle(np, "st,syscfg-eng");
+ if (IS_ERR(ddata.syscfg_eng)) {
+ dev_err(dev, "\"st,syscfg-eng\" not supplied\n");
+ return PTR_ERR(ddata.syscfg_eng);
+ }
+
+ return 0;
+}
+
+static int sti_cpufreq_init(void)
+{
+ int ret;
+
+ ddata.cpu = get_cpu_device(0);
+ if (!ddata.cpu) {
+ dev_err(ddata.cpu, "Failed to get device for CPU0\n");
+ goto skip_voltage_scaling;
+ }
+
+ if (!of_get_property(ddata.cpu->of_node, "operating-points-v2", NULL)) {
+ dev_err(ddata.cpu, "OPP-v2 not supported\n");
+ goto skip_voltage_scaling;
+ }
+
+ ret = sti_cpufreq_fetch_syscon_regsiters();
+ if (ret)
+ goto skip_voltage_scaling;
+
+ ret = sti_cpufreq_set_opp_info();
+ if (!ret)
+ goto register_cpufreq_dt;
+
+skip_voltage_scaling:
+ dev_err(ddata.cpu, "Not doing voltage scaling\n");
+
+register_cpufreq_dt:
+ platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
+
+ return 0;
+}
+module_init(sti_cpufreq_init);
+
+MODULE_DESCRIPTION("STMicroelectronics CPUFreq/OPP driver");
+MODULE_AUTHOR("Ajitpal Singh <ajitpal.singh@st.com>");
+MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PICKME 2/2] dt: cpufreq: st: Provide bindings for ST's CPUFreq implementation
2015-12-10 9:42 ` Lee Jones
@ 2015-12-10 9:42 ` Lee Jones
-1 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel, linux-kernel
Cc: kernel, maxime.coquelin, viresh.kumar, linux-pm, rjw, devicetree,
ajitpal.singh, Lee Jones
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
.../devicetree/bindings/cpufreq/cpufreq-st.txt | 91 ++++++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
new file mode 100644
index 0000000..d91a02a
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
@@ -0,0 +1,91 @@
+Binding for ST's CPUFreq driver
+===============================
+
+ST's CPUFreq driver attempts to read 'process' and 'version' attributes
+from the SoC, then supplies the OPP framework with 'prop' and 'supported
+hardware' information respectively. The framework is then able to read
+the DT and operate in the usual way.
+
+For more information about the expected DT format [See: ../opp/opp.txt].
+
+Frequency Scaling only
+----------------------
+
+No vendor specific driver required for this.
+
+Located in CPU's node:
+
+- operating-points : [See: ../power/opp.txt]
+
+Example [safe]
+--------------
+
+cpus {
+ cpu@0 {
+ /* kHz uV */
+ operating-points = <1500000 0
+ 1200000 0
+ 800000 0
+ 500000 0>;
+ };
+};
+
+Dynamic Voltage and Frequency Scaling (DVFS)
+--------------------------------------------
+
+This requires the ST CPUFreq driver to supply 'process' and 'version' info.
+
+Located in CPU's node:
+
+- operating-points-v2 : [See ../power/opp.txt]
+
+Example [unsafe]
+----------------
+
+cpus {
+ cpu@0 {
+ operating-points-v2 = <&cpu0_opp_table>;
+ };
+};
+
+cpu0_opp_table: opp_table {
+ compatible = "operating-points-v2";
+
+ /* ############################################################### */
+ /* # WARNING: Do not attempt to copy/replicate these nodes, # */
+ /* # they are only to be supplied by the bootloader !!! # */
+ /* ############################################################### */
+ opp0 {
+ /* Major Minor Substrate */
+ /* 2 all all */
+ opp-supported-hw = <0x00000004 0xffffffff 0xffffffff>;
+ opp-hz = /bits/ 64 <1500000000>;
+ clock-latency-ns = <10000000>;
+
+ opp-microvolt-pcode0 = <1200000>;
+ opp-microvolt-pcode1 = <1200000>;
+ opp-microvolt-pcode2 = <1200000>;
+ opp-microvolt-pcode3 = <1200000>;
+ opp-microvolt-pcode4 = <1170000>;
+ opp-microvolt-pcode5 = <1140000>;
+ opp-microvolt-pcode6 = <1100000>;
+ opp-microvolt-pcode7 = <1070000>;
+ };
+
+ opp1 {
+ /* Major Minor Substrate */
+ /* all all all */
+ opp-supported-hw = <0xffffffff 0xffffffff 0xffffffff>;
+ opp-hz = /bits/ 64 <1200000000>;
+ clock-latency-ns = <10000000>;
+
+ opp-microvolt-pcode0 = <1110000>;
+ opp-microvolt-pcode1 = <1150000>;
+ opp-microvolt-pcode2 = <1100000>;
+ opp-microvolt-pcode3 = <1080000>;
+ opp-microvolt-pcode4 = <1040000>;
+ opp-microvolt-pcode5 = <1020000>;
+ opp-microvolt-pcode6 = <980000>;
+ opp-microvolt-pcode7 = <930000>;
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PICKME 2/2] dt: cpufreq: st: Provide bindings for ST's CPUFreq implementation
@ 2015-12-10 9:42 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-10 9:42 UTC (permalink / raw)
To: linux-arm-kernel
Cc: devicetree at vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
.../devicetree/bindings/cpufreq/cpufreq-st.txt | 91 ++++++++++++++++++++++
1 file changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
new file mode 100644
index 0000000..d91a02a
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt
@@ -0,0 +1,91 @@
+Binding for ST's CPUFreq driver
+===============================
+
+ST's CPUFreq driver attempts to read 'process' and 'version' attributes
+from the SoC, then supplies the OPP framework with 'prop' and 'supported
+hardware' information respectively. The framework is then able to read
+the DT and operate in the usual way.
+
+For more information about the expected DT format [See: ../opp/opp.txt].
+
+Frequency Scaling only
+----------------------
+
+No vendor specific driver required for this.
+
+Located in CPU's node:
+
+- operating-points : [See: ../power/opp.txt]
+
+Example [safe]
+--------------
+
+cpus {
+ cpu at 0 {
+ /* kHz uV */
+ operating-points = <1500000 0
+ 1200000 0
+ 800000 0
+ 500000 0>;
+ };
+};
+
+Dynamic Voltage and Frequency Scaling (DVFS)
+--------------------------------------------
+
+This requires the ST CPUFreq driver to supply 'process' and 'version' info.
+
+Located in CPU's node:
+
+- operating-points-v2 : [See ../power/opp.txt]
+
+Example [unsafe]
+----------------
+
+cpus {
+ cpu at 0 {
+ operating-points-v2 = <&cpu0_opp_table>;
+ };
+};
+
+cpu0_opp_table: opp_table {
+ compatible = "operating-points-v2";
+
+ /* ############################################################### */
+ /* # WARNING: Do not attempt to copy/replicate these nodes, # */
+ /* # they are only to be supplied by the bootloader !!! # */
+ /* ############################################################### */
+ opp0 {
+ /* Major Minor Substrate */
+ /* 2 all all */
+ opp-supported-hw = <0x00000004 0xffffffff 0xffffffff>;
+ opp-hz = /bits/ 64 <1500000000>;
+ clock-latency-ns = <10000000>;
+
+ opp-microvolt-pcode0 = <1200000>;
+ opp-microvolt-pcode1 = <1200000>;
+ opp-microvolt-pcode2 = <1200000>;
+ opp-microvolt-pcode3 = <1200000>;
+ opp-microvolt-pcode4 = <1170000>;
+ opp-microvolt-pcode5 = <1140000>;
+ opp-microvolt-pcode6 = <1100000>;
+ opp-microvolt-pcode7 = <1070000>;
+ };
+
+ opp1 {
+ /* Major Minor Substrate */
+ /* all all all */
+ opp-supported-hw = <0xffffffff 0xffffffff 0xffffffff>;
+ opp-hz = /bits/ 64 <1200000000>;
+ clock-latency-ns = <10000000>;
+
+ opp-microvolt-pcode0 = <1110000>;
+ opp-microvolt-pcode1 = <1150000>;
+ opp-microvolt-pcode2 = <1100000>;
+ opp-microvolt-pcode3 = <1080000>;
+ opp-microvolt-pcode4 = <1040000>;
+ opp-microvolt-pcode5 = <1020000>;
+ opp-microvolt-pcode6 = <980000>;
+ opp-microvolt-pcode7 = <930000>;
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PICKME 0/2] cpufreq: New ST driver
2015-12-10 9:42 ` Lee Jones
@ 2015-12-10 9:45 ` Viresh Kumar
-1 siblings, 0 replies; 17+ messages in thread
From: Viresh Kumar @ 2015-12-10 9:45 UTC (permalink / raw)
To: Lee Jones
Cc: linux-arm-kernel, linux-kernel, kernel, maxime.coquelin,
linux-pm, rjw, devicetree, ajitpal.singh
On 10-12-15, 09:42, Lee Jones wrote:
> Hi Rafael,
>
> Would you be kind enough to pick these 2 patches up please.
> The have the required Acks.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
--
viresh
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-10 9:45 ` Viresh Kumar
0 siblings, 0 replies; 17+ messages in thread
From: Viresh Kumar @ 2015-12-10 9:45 UTC (permalink / raw)
To: linux-arm-kernel
On 10-12-15, 09:42, Lee Jones wrote:
> Hi Rafael,
>
> Would you be kind enough to pick these 2 patches up please.
> The have the required Acks.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
--
viresh
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PICKME 0/2] cpufreq: New ST driver
2015-12-10 9:42 ` Lee Jones
@ 2015-12-10 21:38 ` Rafael J. Wysocki
-1 siblings, 0 replies; 17+ messages in thread
From: Rafael J. Wysocki @ 2015-12-10 21:38 UTC (permalink / raw)
To: Lee Jones
Cc: linux-arm-kernel, linux-kernel, kernel, maxime.coquelin,
viresh.kumar, linux-pm, devicetree, ajitpal.singh
On Thursday, December 10, 2015 09:42:15 AM Lee Jones wrote:
> Hi Rafael,
>
> Would you be kind enough to pick these 2 patches up please.
> The have the required Acks.
I can do that.
Do they depend on anything special?
Thanks,
Rafael
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-10 21:38 ` Rafael J. Wysocki
0 siblings, 0 replies; 17+ messages in thread
From: Rafael J. Wysocki @ 2015-12-10 21:38 UTC (permalink / raw)
To: linux-arm-kernel
On Thursday, December 10, 2015 09:42:15 AM Lee Jones wrote:
> Hi Rafael,
>
> Would you be kind enough to pick these 2 patches up please.
> The have the required Acks.
I can do that.
Do they depend on anything special?
Thanks,
Rafael
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PICKME 0/2] cpufreq: New ST driver
2015-12-10 21:38 ` Rafael J. Wysocki
@ 2015-12-11 3:19 ` Viresh Kumar
-1 siblings, 0 replies; 17+ messages in thread
From: Viresh Kumar @ 2015-12-11 3:19 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Lee Jones, linux-arm-kernel, linux-kernel, kernel,
maxime.coquelin, linux-pm, devicetree, ajitpal.singh
On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> Do they depend on anything special?
My opp-binding-parsing patches which you applied to bleeding-edge.
Yes, Lee should have mentioned that explicitly.
--
viresh
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-11 3:19 ` Viresh Kumar
0 siblings, 0 replies; 17+ messages in thread
From: Viresh Kumar @ 2015-12-11 3:19 UTC (permalink / raw)
To: linux-arm-kernel
On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> Do they depend on anything special?
My opp-binding-parsing patches which you applied to bleeding-edge.
Yes, Lee should have mentioned that explicitly.
--
viresh
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PICKME 0/2] cpufreq: New ST driver
2015-12-11 3:19 ` Viresh Kumar
@ 2015-12-11 7:05 ` Lee Jones
-1 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-11 7:05 UTC (permalink / raw)
To: Viresh Kumar
Cc: Rafael J. Wysocki, linux-arm-kernel, linux-kernel, kernel,
maxime.coquelin, linux-pm, devicetree, ajitpal.singh
On Fri, 11 Dec 2015, Viresh Kumar wrote:
> On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> > Do they depend on anything special?
>
> My opp-binding-parsing patches which you applied to bleeding-edge.
I thought these had already been applied.
> Yes, Lee should have mentioned that explicitly.
Aye, apologies for that.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-11 7:05 ` Lee Jones
0 siblings, 0 replies; 17+ messages in thread
From: Lee Jones @ 2015-12-11 7:05 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, 11 Dec 2015, Viresh Kumar wrote:
> On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> > Do they depend on anything special?
>
> My opp-binding-parsing patches which you applied to bleeding-edge.
I thought these had already been applied.
> Yes, Lee should have mentioned that explicitly.
Aye, apologies for that.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PICKME 0/2] cpufreq: New ST driver
2015-12-11 7:05 ` Lee Jones
@ 2015-12-15 0:01 ` Rafael J. Wysocki
-1 siblings, 0 replies; 17+ messages in thread
From: Rafael J. Wysocki @ 2015-12-15 0:01 UTC (permalink / raw)
To: Lee Jones
Cc: Viresh Kumar, linux-arm-kernel, linux-kernel, kernel,
maxime.coquelin, linux-pm, devicetree, ajitpal.singh
On Friday, December 11, 2015 07:05:32 AM Lee Jones wrote:
> On Fri, 11 Dec 2015, Viresh Kumar wrote:
> > On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> > > Do they depend on anything special?
> >
> > My opp-binding-parsing patches which you applied to bleeding-edge.
>
> I thought these had already been applied.
>
> > Yes, Lee should have mentioned that explicitly.
>
> Aye, apologies for that.
No prob, applied now.
Thanks,
Rafael
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PICKME 0/2] cpufreq: New ST driver
@ 2015-12-15 0:01 ` Rafael J. Wysocki
0 siblings, 0 replies; 17+ messages in thread
From: Rafael J. Wysocki @ 2015-12-15 0:01 UTC (permalink / raw)
To: linux-arm-kernel
On Friday, December 11, 2015 07:05:32 AM Lee Jones wrote:
> On Fri, 11 Dec 2015, Viresh Kumar wrote:
> > On 10-12-15, 22:38, Rafael J. Wysocki wrote:
> > > Do they depend on anything special?
> >
> > My opp-binding-parsing patches which you applied to bleeding-edge.
>
> I thought these had already been applied.
>
> > Yes, Lee should have mentioned that explicitly.
>
> Aye, apologies for that.
No prob, applied now.
Thanks,
Rafael
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2015-12-15 0:01 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-12-10 9:42 [PICKME 0/2] cpufreq: New ST driver Lee Jones
2015-12-10 9:42 ` Lee Jones
2015-12-10 9:42 ` [PICKME 1/2] cpufreq: st: Provide runtime initialised driver for ST's platforms Lee Jones
2015-12-10 9:42 ` Lee Jones
2015-12-10 9:42 ` Lee Jones
2015-12-10 9:42 ` [PICKME 2/2] dt: cpufreq: st: Provide bindings for ST's CPUFreq implementation Lee Jones
2015-12-10 9:42 ` Lee Jones
2015-12-10 9:45 ` [PICKME 0/2] cpufreq: New ST driver Viresh Kumar
2015-12-10 9:45 ` Viresh Kumar
2015-12-10 21:38 ` Rafael J. Wysocki
2015-12-10 21:38 ` Rafael J. Wysocki
2015-12-11 3:19 ` Viresh Kumar
2015-12-11 3:19 ` Viresh Kumar
2015-12-11 7:05 ` Lee Jones
2015-12-11 7:05 ` Lee Jones
2015-12-15 0:01 ` Rafael J. Wysocki
2015-12-15 0:01 ` Rafael J. Wysocki
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.