* [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics
@ 2016-01-12 18:01 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
This patchset adds support for some more modules from Ka-Ro
electronics GmbH based on i.MX6SOLO and i.MX6UL.
The last patch adds another LVDS display for the existing TX6 LVDS
modules.
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics
@ 2016-01-12 18:01 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: linux-arm-kernel
This patchset adds support for some more modules from Ka-Ro
electronics GmbH based on i.MX6SOLO and i.MX6UL.
The last patch adds another LVDS display for the existing TX6 LVDS
modules.
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
2016-01-12 18:01 ` Lothar Waßmann
@ 2016-01-12 18:01 ` Lothar Waßmann
-1 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Cc: Lothar Waßmann
Add support for the TX6S-8034 module from Ka-Ro electronics.
The module is equipped with an i.MX6SOLO at 792MHz, 256MiB DDR3 SDRAM
and 128MiB NAND flash.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 255 +++++++++++++++++++++++++++++++++
2 files changed, 256 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a4a6d70..ac406d8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
+ imx6dl-tx6s-8034.dtb \
imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-811x.dtb \
imx6dl-udoo.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
new file mode 100644
index 0000000..6545335
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
@@ -0,0 +1,255 @@
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8034 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+ timestamp = __DATE__, __TIME__;
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu@1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display@di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ interface-pix-fmt = "rgb24";
+// fsl,panel = <&lcd0_panel>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lcd0_panel: lcd-panel {
+ compatible = "edt,et070080dh6", "simple-panel";
+ power-supply = <®_lcd0_pwr>;
+ enable-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+ status = "disabled";
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&pinctrl_hog {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
+ >;
+};
+
+&pinctrl_usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+®_lcd1_pwr {
+ status = "disabled";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
@ 2016-01-12 18:01 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: linux-arm-kernel
Add support for the TX6S-8034 module from Ka-Ro electronics.
The module is equipped with an i.MX6SOLO at 792MHz, 256MiB DDR3 SDRAM
and 128MiB NAND flash.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 255 +++++++++++++++++++++++++++++++++
2 files changed, 256 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a4a6d70..ac406d8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
+ imx6dl-tx6s-8034.dtb \
imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-811x.dtb \
imx6dl-udoo.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
new file mode 100644
index 0000000..6545335
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
@@ -0,0 +1,255 @@
+/*
+ * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8034 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+ timestamp = __DATE__, __TIME__;
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ interface-pix-fmt = "rgb24";
+// fsl,panel = <&lcd0_panel>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lcd0_panel: lcd-panel {
+ compatible = "edt,et070080dh6", "simple-panel";
+ power-supply = <®_lcd0_pwr>;
+ enable-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+ status = "disabled";
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&pinctrl_hog {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
+ >;
+};
+
+&pinctrl_usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+®_lcd1_pwr {
+ status = "disabled";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
2016-01-12 18:01 ` Lothar Waßmann
@ 2016-01-12 18:01 ` Lothar Waßmann
-1 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Cc: Lothar Waßmann
Add support for two module variants from Ka-Ro electronics equipped
with an i.MX6UL processor running at 528MHz.
Both modules are equipped with 256MiB DDR3 SDRAM.
The TXUL-0010 has 128MiB NAND flash, while the TXUL-0011 is equipped
with 4GiB eMMC.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +-
arch/arm/boot/dts/imx6ul-txul-0010.dts | 54 ++
arch/arm/boot/dts/imx6ul-txul-0011.dts | 85 +++
arch/arm/boot/dts/imx6ul-txul.dtsi | 948 +++++++++++++++++++++++++++++++++
4 files changed, 1090 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ul-txul-0010.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-0011.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ac406d8..d7c3bdd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -359,7 +359,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb.dtb
dtb-$(CONFIG_SOC_IMX6UL) += \
- imx6ul-14x14-evk.dtb
+ imx6ul-14x14-evk.dtb \
+ imx6ul-txul-0010.dtb \
+ imx6ul-txul-0011.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-sbc-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-txul-0010.dts b/arch/arm/boot/dts/imx6ul-txul-0010.dts
new file mode 100644
index 0000000..5e0b09f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-0010.dts
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-txul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0010 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ mmc0 = &usdhc1;
+ /delete-property/ mmc1;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-0011.dts b/arch/arm/boot/dts/imx6ul-txul-0011.dts
new file mode 100644
index 0000000..40103ea
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-0011.dts
@@ -0,0 +1,85 @@
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-txul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0011 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ };
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&iomuxc {
+ imx6qdl-tx6 {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
+ /* eMMC RESET */
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ fsl,wp-controller;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul.dtsi b/arch/arm/boot/dts/imx6ul-txul.dtsi
new file mode 100644
index 0000000..e203999
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul.dtsi
@@ -0,0 +1,948 @@
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ can0 = &can2;
+ can1 = &can1;
+ display = &display;
+ i2c0 = &i2c_gpio;
+ i2c1 = &i2c2;
+ lcdif_23bit_pins_a = &pinctrl_disp0_1;
+ lcdif_24bit_pins_a = &pinctrl_disp0_2;
+ pwm0 = &pwm5;
+ reg_can_xcvr = ®_can_xcvr;
+ serial2 = &uart5;
+ serial4 = &uart3;
+ spi0 = &ecspi2;
+ spi1 = &spi_gpio;
+ stk5led = &user_led;
+ usbh1 = &usbotg2;
+ usbotg = &usbotg1;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0 0>; /* will be filled by U-Boot */
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mclk: clock@0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ };
+
+ i2c_gpio: i2c-gpio {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio>;
+ gpios = <
+ &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
+ &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
+ >;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ds1339: rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ status = "disabled";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led: user {
+ label = "Heartbeat";
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3v3_etn: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_2v5: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_can_xcvr: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
+
+ reg_lcd_pwr: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwr>;
+ gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_lcd_reset: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_reset>;
+ gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: regulator@8 {
+ compatible = "regulator-fixed";
+ reg = <8>;
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ spi_gpio: spi-gpio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "spi-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi_gpio>;
+ gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "disabled";
+
+ spi@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+ };
+
+ spi@1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <54000000>;
+ };
+ };
+
+ sound {
+ compatible = "karo,imx6ul-tx6ul-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6ul-tx6ul-sgtl5000-audio";
+ ssi-controller = <&sai2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ fsl,no-audmux;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "okay";
+
+ spi@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+ };
+
+ spi@1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <54000000>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet_mdio>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+ phy-supply = <®_3v3_etn>;
+ phy-handle = <&etnphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5>;
+ status = "okay";
+ };
+
+ etnphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ status = "okay";
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-supply = <®_3v3_etn>;
+ phy-handle = <&etnphy1>;
+ status = "disabled";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ fsl,no-blockmark-swap;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ sgtl5000: sgtl5000@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_2v5>;
+ VDDIO-supply = <®_3v3>;
+ clocks = <&mclk>;
+ };
+
+ polytouch: edt-ft5x06@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+
+ touchscreen: tsc2007@48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2007>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 0>;
+ gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ ti,x-plate-ohms = <660>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6qdl-tx6 {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */
+ MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */
+ >;
+ };
+
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */
+ MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x0b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x0b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x0b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x0b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x0b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x0b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x0b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40000031
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x0b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x0b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x0b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x0b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x0b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x0b0b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x0b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x40000031
+ >;
+ };
+
+ pinctrl_enet_mdio: enet-mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_etnphy_power: etnphy-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b0b0
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c_gpio: i2c-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0
+ MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0
+ >;
+ };
+
+ pinctrl_lcd_pwr: lcd-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */
+ >;
+ };
+
+ pinctrl_lcd_reset: lcd-resetgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD RESET */
+ >;
+ };
+
+ pinctrl_pwm5: pwm5grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */
+ >;
+ };
+
+ pinctrl_spi_gpio: spi-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart1_rtscts: uart1_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2_rtscts: uart2_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0
+ MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5_rtscts: uart5_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0
+ MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_usbh1_oc: usbh1-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */
+ >;
+ };
+
+ pinctrl_usbotg_oc: usbotg-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
+ /* SD1 CD */
+ MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */
+ >;
+ };
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
+ /* eMMC RESET */
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7 */
+ linux,keymap = <
+ MATRIX_KEY(6, 6, KEY_POWER) /* 0x06060074 */
+ MATRIX_KEY(6, 7, KEY_KP0) /* 0x06070052 */
+ MATRIX_KEY(6, 2, KEY_KP1) /* 0x0602004f */
+ MATRIX_KEY(6, 3, KEY_KP2) /* 0x06030050 */
+ MATRIX_KEY(7, 6, KEY_KP3) /* 0x07060051 */
+ MATRIX_KEY(7, 7, KEY_KP4) /* 0x0707004b */
+ MATRIX_KEY(7, 2, KEY_KP5) /* 0x0702004c */
+ MATRIX_KEY(7, 3, KEY_KP6) /* 0x0703004d */
+ MATRIX_KEY(2, 6, KEY_KP7) /* 0x02060047 */
+ MATRIX_KEY(2, 7, KEY_KP8) /* 0x02070048 */
+ MATRIX_KEY(2, 2, KEY_KP9) /* 0x02020049 */
+ >;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ lcd-supply = <®_lcd_pwr>;
+ display = <&display>;
+ status = "okay";
+
+ display: display@di0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+ status = "okay";
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm5>;
+ #pwm-cells = <3>;
+ status = "okay";
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usbotg_vbus>;
+ dr_mode = "peripheral";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ bus-width = <4>;
+ no-1-8-v;
+ cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+ fsl,wp-controller;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-12 18:01 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: linux-arm-kernel
Add support for two module variants from Ka-Ro electronics equipped
with an i.MX6UL processor running at 528MHz.
Both modules are equipped with 256MiB DDR3 SDRAM.
The TXUL-0010 has 128MiB NAND flash, while the TXUL-0011 is equipped
with 4GiB eMMC.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +-
arch/arm/boot/dts/imx6ul-txul-0010.dts | 54 ++
arch/arm/boot/dts/imx6ul-txul-0011.dts | 85 +++
arch/arm/boot/dts/imx6ul-txul.dtsi | 948 +++++++++++++++++++++++++++++++++
4 files changed, 1090 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ul-txul-0010.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul-0011.dts
create mode 100644 arch/arm/boot/dts/imx6ul-txul.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ac406d8..d7c3bdd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -359,7 +359,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb.dtb
dtb-$(CONFIG_SOC_IMX6UL) += \
- imx6ul-14x14-evk.dtb
+ imx6ul-14x14-evk.dtb \
+ imx6ul-txul-0010.dtb \
+ imx6ul-txul-0011.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-sbc-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-txul-0010.dts b/arch/arm/boot/dts/imx6ul-txul-0010.dts
new file mode 100644
index 0000000..5e0b09f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-0010.dts
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-txul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0010 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ mmc0 = &usdhc1;
+ /delete-property/ mmc1;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul-0011.dts b/arch/arm/boot/dts/imx6ul-txul-0011.dts
new file mode 100644
index 0000000..40103ea
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul-0011.dts
@@ -0,0 +1,85 @@
+/*
+ * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-txul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0011 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ };
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&iomuxc {
+ imx6qdl-tx6 {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
+ /* eMMC RESET */
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ fsl,wp-controller;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul-txul.dtsi b/arch/arm/boot/dts/imx6ul-txul.dtsi
new file mode 100644
index 0000000..e203999
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-txul.dtsi
@@ -0,0 +1,948 @@
+/*
+ * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ can0 = &can2;
+ can1 = &can1;
+ display = &display;
+ i2c0 = &i2c_gpio;
+ i2c1 = &i2c2;
+ lcdif_23bit_pins_a = &pinctrl_disp0_1;
+ lcdif_24bit_pins_a = &pinctrl_disp0_2;
+ pwm0 = &pwm5;
+ reg_can_xcvr = ®_can_xcvr;
+ serial2 = &uart5;
+ serial4 = &uart3;
+ spi0 = &ecspi2;
+ spi1 = &spi_gpio;
+ stk5led = &user_led;
+ usbh1 = &usbotg2;
+ usbotg = &usbotg1;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0 0>; /* will be filled by U-Boot */
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mclk: clock at 0 {
+ compatible = "fixed-clock";
+ reg = <0>;
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ };
+
+ i2c_gpio: i2c-gpio {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio>;
+ gpios = <
+ &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
+ &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
+ >;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ds1339: rtc at 68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ status = "disabled";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led: user {
+ label = "Heartbeat";
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3v3_etn: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_2v5: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_can_xcvr: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
+
+ reg_lcd_pwr: regulator at 5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwr>;
+ gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_lcd_reset: regulator at 6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_reset>;
+ gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: regulator at 7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: regulator at 8 {
+ compatible = "regulator-fixed";
+ reg = <8>;
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ spi_gpio: spi-gpio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "spi-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi_gpio>;
+ gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "disabled";
+
+ spi at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+ };
+
+ spi at 1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <54000000>;
+ };
+ };
+
+ sound {
+ compatible = "karo,imx6ul-tx6ul-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6ul-tx6ul-sgtl5000-audio";
+ ssi-controller = <&sai2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ fsl,no-audmux;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "okay";
+
+ spi at 0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+ };
+
+ spi at 1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <54000000>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet_mdio>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+ phy-supply = <®_3v3_etn>;
+ phy-handle = <&etnphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5>;
+ status = "okay";
+ };
+
+ etnphy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ status = "okay";
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-supply = <®_3v3_etn>;
+ phy-handle = <&etnphy1>;
+ status = "disabled";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ fsl,no-blockmark-swap;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ sgtl5000: sgtl5000 at 0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_2v5>;
+ VDDIO-supply = <®_3v3>;
+ clocks = <&mclk>;
+ };
+
+ polytouch: edt-ft5x06 at 38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+
+ touchscreen: tsc2007 at 48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2007>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 0>;
+ gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ ti,x-plate-ohms = <660>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6qdl-tx6 {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */
+ MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */
+ >;
+ };
+
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */
+ MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x0b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x0b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x0b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x0b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x0b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x0b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x0b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x40000031
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x0b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x0b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x0b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x0b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x0b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x0b0b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x0b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x40000031
+ >;
+ };
+
+ pinctrl_enet_mdio: enet-mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_etnphy_power: etnphy-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b0b0
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c_gpio: i2c-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0
+ MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0
+ >;
+ };
+
+ pinctrl_lcd_pwr: lcd-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */
+ >;
+ };
+
+ pinctrl_lcd_reset: lcd-resetgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD RESET */
+ >;
+ };
+
+ pinctrl_pwm5: pwm5grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */
+ >;
+ };
+
+ pinctrl_spi_gpio: spi-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart1_rtscts: uart1_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2_rtscts: uart2_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0
+ MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5_rtscts: uart5_rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0
+ MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_usbh1_oc: usbh1-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */
+ >;
+ };
+
+ pinctrl_usbotg_oc: usbotg-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
+ /* SD1 CD */
+ MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */
+ >;
+ };
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
+ /* eMMC RESET */
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ /* sample keymap */
+ /* row/col 0,1 are mapped to KPP row/col 6,7 */
+ linux,keymap = <
+ MATRIX_KEY(6, 6, KEY_POWER) /* 0x06060074 */
+ MATRIX_KEY(6, 7, KEY_KP0) /* 0x06070052 */
+ MATRIX_KEY(6, 2, KEY_KP1) /* 0x0602004f */
+ MATRIX_KEY(6, 3, KEY_KP2) /* 0x06030050 */
+ MATRIX_KEY(7, 6, KEY_KP3) /* 0x07060051 */
+ MATRIX_KEY(7, 7, KEY_KP4) /* 0x0707004b */
+ MATRIX_KEY(7, 2, KEY_KP5) /* 0x0702004c */
+ MATRIX_KEY(7, 3, KEY_KP6) /* 0x0703004d */
+ MATRIX_KEY(2, 6, KEY_KP7) /* 0x02060047 */
+ MATRIX_KEY(2, 7, KEY_KP8) /* 0x02070048 */
+ MATRIX_KEY(2, 2, KEY_KP9) /* 0x02020049 */
+ >;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ lcd-supply = <®_lcd_pwr>;
+ display = <&display>;
+ status = "okay";
+
+ display: display at di0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+ status = "okay";
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm5>;
+ #pwm-cells = <3>;
+ status = "okay";
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usbotg_vbus>;
+ dr_mode = "peripheral";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ bus-width = <4>;
+ no-1-8-v;
+ cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+ fsl,wp-controller;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules
2016-01-12 18:01 ` Lothar Waßmann
@ 2016-01-12 18:01 ` Lothar Waßmann
-1 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Cc: Lothar Waßmann
Add support for the NLT Technologies WXGA LVDS display NL12880BC20 to
the TX6 LVDS modules from Ka-Ro electronics.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 42 ++++++++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1110.dts | 42 ++++++++++++++++++++++++++++++----
2 files changed, 76 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
index c275eec..c14ee8f 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
@@ -104,8 +104,9 @@
status = "okay";
display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -118,6 +119,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds0_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
@@ -127,8 +144,9 @@
status = "disabled";
display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -141,6 +159,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds1_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
index 88aa1e4..7a8be02 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
@@ -104,8 +104,9 @@
status = "okay";
display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -118,6 +119,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds0_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
@@ -127,8 +144,9 @@
status = "disabled";
display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -141,6 +159,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds1_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules
@ 2016-01-12 18:01 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-12 18:01 UTC (permalink / raw)
To: linux-arm-kernel
Add support for the NLT Technologies WXGA LVDS display NL12880BC20 to
the TX6 LVDS modules from Ka-Ro electronics.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 42 ++++++++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1110.dts | 42 ++++++++++++++++++++++++++++++----
2 files changed, 76 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
index c275eec..c14ee8f 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
@@ -104,8 +104,9 @@
status = "okay";
display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -118,6 +119,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds0_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
@@ -127,8 +144,9 @@
status = "disabled";
display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -141,6 +159,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds1_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
index 88aa1e4..7a8be02 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
@@ -104,8 +104,9 @@
status = "okay";
display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -118,6 +119,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds0_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
@@ -127,8 +144,9 @@
status = "disabled";
display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
clock-frequency = <65000000>;
hactive = <1024>;
vactive = <768>;
@@ -141,6 +159,22 @@
de-active = <1>;
pixelclk-active = <1>;
};
+
+ lvds1_timing1: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hsync-len = <60>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vsync-len = <13>;
+ vfront-porch = <5>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
};
};
};
--
2.1.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-12 18:43 ` Fabio Estevam
0 siblings, 0 replies; 19+ messages in thread
From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw)
To: Lothar Waßmann
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote:
> + spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <54000000>;
> + };
> +
> + spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <54000000>;
> + };
> + };
If you leave the spidev node, the spi core will complain loudly about it.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-12 18:43 ` Fabio Estevam
0 siblings, 0 replies; 19+ messages in thread
From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw)
To: Lothar Waßmann
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel
On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote:
> + spi@0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <54000000>;
> + };
> +
> + spi@1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <54000000>;
> + };
> + };
If you leave the spidev node, the spi core will complain loudly about it.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-12 18:43 ` Fabio Estevam
0 siblings, 0 replies; 19+ messages in thread
From: Fabio Estevam @ 2016-01-12 18:43 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Jan 12, 2016 at 4:01 PM, Lothar Wa?mann <LW@karo-electronics.de> wrote:
> + spi at 0 {
> + compatible = "spidev";
> + reg = <0>;
> + spi-max-frequency = <54000000>;
> + };
> +
> + spi at 1 {
> + compatible = "spidev";
> + reg = <1>;
> + spi-max-frequency = <54000000>;
> + };
> + };
If you leave the spidev node, the spi core will complain loudly about it.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
@ 2016-01-13 7:35 ` Holger Schurig
0 siblings, 0 replies; 19+ messages in thread
From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw)
To: Lothar Waßmann
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Lothar Waßmann <LW@KARO-electronics.de> writes:
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> + timestamp = __DATE__, __TIME__;
Is this needed or useful?
There's a movement that aims to do "reproducible builds" ... being
able to recompile an image and verify it against the supplied can be
helpful for security audit purposes.
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + interface-pix-fmt = "rgb24";
> +// fsl,panel = <&lcd0_panel>;
Probably not for upstream inclusion?
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
@ 2016-01-13 7:35 ` Holger Schurig
0 siblings, 0 replies; 19+ messages in thread
From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw)
To: Lothar Waßmann
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Lothar Waßmann <LW-bxm8fMRDkQLDiMYJYoSAnRvVK+yQ3ZXh@public.gmane.org> writes:
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> + timestamp = __DATE__, __TIME__;
Is this needed or useful?
There's a movement that aims to do "reproducible builds" ... being
able to recompile an image and verify it against the supplied can be
helpful for security audit purposes.
> + display: display@di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + interface-pix-fmt = "rgb24";
> +// fsl,panel = <&lcd0_panel>;
Probably not for upstream inclusion?
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
@ 2016-01-13 7:35 ` Holger Schurig
0 siblings, 0 replies; 19+ messages in thread
From: Holger Schurig @ 2016-01-13 7:35 UTC (permalink / raw)
To: linux-arm-kernel
Lothar Wa?mann <LW@KARO-electronics.de> writes:
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> + timestamp = __DATE__, __TIME__;
Is this needed or useful?
There's a movement that aims to do "reproducible builds" ... being
able to recompile an image and verify it against the supplied can be
helpful for security audit purposes.
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + interface-pix-fmt = "rgb24";
> +// fsl,panel = <&lcd0_panel>;
Probably not for upstream inclusion?
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
2016-01-13 7:35 ` Holger Schurig
@ 2016-01-13 11:10 ` Lothar Waßmann
-1 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-13 11:10 UTC (permalink / raw)
To: Holger Schurig
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Hi,
> Lothar Waßmann <LW@KARO-electronics.de> writes:
>
> > +/ {
> > + model = "Ka-Ro electronics TX6S-8034 Module";
> > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> > + timestamp = __DATE__, __TIME__;
>
> Is this needed or useful?
>
> There's a movement that aims to do "reproducible builds" ... being
> able to recompile an image and verify it against the supplied can be
> helpful for security audit purposes.
>
Ooops. I was on the wrong branch when creating these patches. Will
resend this patch series soon.
> > + display: display@di0 {
> > + compatible = "fsl,imx-parallel-display";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_disp0_1>;
> > + interface-pix-fmt = "rgb24";
> > +// fsl,panel = <&lcd0_panel>;
>
> Probably not for upstream inclusion?
>
see above.
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module
@ 2016-01-13 11:10 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-13 11:10 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
> Lothar Wa?mann <LW@KARO-electronics.de> writes:
>
> > +/ {
> > + model = "Ka-Ro electronics TX6S-8034 Module";
> > + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> > + timestamp = __DATE__, __TIME__;
>
> Is this needed or useful?
>
> There's a movement that aims to do "reproducible builds" ... being
> able to recompile an image and verify it against the supplied can be
> helpful for security audit purposes.
>
Ooops. I was on the wrong branch when creating these patches. Will
resend this patch series soon.
> > + display: display at di0 {
> > + compatible = "fsl,imx-parallel-display";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_disp0_1>;
> > + interface-pix-fmt = "rgb24";
> > +// fsl,panel = <&lcd0_panel>;
>
> Probably not for upstream inclusion?
>
see above.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-13 11:36 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw)
To: Fabio Estevam
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo, devicetree,
linux-arm-kernel, linux-kernel
Hi,
> On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote:
>
> > + spi@0 {
> > + compatible = "spidev";
> > + reg = <0>;
> > + spi-max-frequency = <54000000>;
> > + };
> > +
> > + spi@1 {
> > + compatible = "spidev";
> > + reg = <1>;
> > + spi-max-frequency = <54000000>;
> > + };
> > + };
>
> If you leave the spidev node, the spi core will complain loudly about it.
>
I know. But this gives the opportunity to test the SPI interface
without any bogus chip definitions.
Lothar Waßmann
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-13 11:36 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw)
To: Fabio Estevam
Cc: Ian Campbell, Kumar Gala, Mark Rutland, Pawel Moll, Rob Herring,
Russell King, Sascha Hauer, Shawn Guo,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-kernel
Hi,
> On Tue, Jan 12, 2016 at 4:01 PM, Lothar Waßmann <LW@karo-electronics.de> wrote:
>
> > + spi@0 {
> > + compatible = "spidev";
> > + reg = <0>;
> > + spi-max-frequency = <54000000>;
> > + };
> > +
> > + spi@1 {
> > + compatible = "spidev";
> > + reg = <1>;
> > + spi-max-frequency = <54000000>;
> > + };
> > + };
>
> If you leave the spidev node, the spi core will complain loudly about it.
>
I know. But this gives the opportunity to test the SPI interface
without any bogus chip definitions.
Lothar Waßmann
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
@ 2016-01-13 11:36 ` Lothar Waßmann
0 siblings, 0 replies; 19+ messages in thread
From: Lothar Waßmann @ 2016-01-13 11:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
> On Tue, Jan 12, 2016 at 4:01 PM, Lothar Wa?mann <LW@karo-electronics.de> wrote:
>
> > + spi at 0 {
> > + compatible = "spidev";
> > + reg = <0>;
> > + spi-max-frequency = <54000000>;
> > + };
> > +
> > + spi at 1 {
> > + compatible = "spidev";
> > + reg = <1>;
> > + spi-max-frequency = <54000000>;
> > + };
> > + };
>
> If you leave the spidev node, the spi core will complain loudly about it.
>
I know. But this gives the opportunity to test the SPI interface
without any bogus chip definitions.
Lothar Wa?mann
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2016-01-13 11:36 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-01-12 18:01 [PATCH 0/3] ARM: dts: imx6: add support for more i.MX6 modules from Ka-Ro electronics Lothar Waßmann
2016-01-12 18:01 ` Lothar Waßmann
2016-01-12 18:01 ` [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module Lothar Waßmann
2016-01-12 18:01 ` Lothar Waßmann
2016-01-12 18:01 ` [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules Lothar Waßmann
2016-01-12 18:01 ` Lothar Waßmann
2016-01-12 18:01 ` [PATCH 3/3] ARM: dts: imx6: add display timing for NL12880BC20 display to Ka-Ro electronics TX6 LVDS modules Lothar Waßmann
2016-01-12 18:01 ` Lothar Waßmann
2016-01-12 18:43 ` [PATCH 2/3] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules Fabio Estevam
2016-01-12 18:43 ` Fabio Estevam
2016-01-12 18:43 ` Fabio Estevam
2016-01-13 11:36 ` Lothar Waßmann
2016-01-13 11:36 ` Lothar Waßmann
2016-01-13 11:36 ` Lothar Waßmann
2016-01-13 7:35 ` [PATCH 1/3] ARM: dts: imx6: add support for Ka-Ro electronics TX6S-8034 module Holger Schurig
2016-01-13 7:35 ` Holger Schurig
2016-01-13 7:35 ` Holger Schurig
2016-01-13 11:10 ` Lothar Waßmann
2016-01-13 11:10 ` Lothar Waßmann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.