[PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/Kconfig      |  6 +++---
 drivers/rtc/rtc-jz4740.c | 50 ++++++++++++++++++++++++++++++++++++++++++++++--
 2 files changed, 51 insertions(+), 5 deletions(-)

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index e593c55..b322f08 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1494,10 +1494,10 @@ config RTC_DRV_MPC5121
 
 config RTC_DRV_JZ4740
 	tristate "Ingenic JZ4740 SoC"
-	depends on MACH_JZ4740 || COMPILE_TEST
+	depends on MACH_INGENIC || COMPILE_TEST
 	help
-	  If you say yes here you get support for the Ingenic JZ4740 SoC RTC
-	  controller.
+	  If you say yes here you get support for the Ingenic JZ47xx SoCs RTC
+	  controllers.
 
 	  This driver can also be buillt as a module. If so, the module
 	  will be called rtc-jz4740.
diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index b2bcfc0..47617bd 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -29,6 +29,10 @@
 #define JZ_REG_RTC_HIBERNATE	0x20
 #define JZ_REG_RTC_SCRATCHPAD	0x34
 
+/* The following are present on the jz4780 */
+#define JZ_REG_RTC_WENR	0x3C
+#define JZ_RTC_WENR_WEN	BIT(31)
+
 #define JZ_RTC_CTRL_WRDY	BIT(7)
 #define JZ_RTC_CTRL_1HZ		BIT(6)
 #define JZ_RTC_CTRL_1HZ_IRQ	BIT(5)
@@ -37,8 +41,17 @@
 #define JZ_RTC_CTRL_AE		BIT(2)
 #define JZ_RTC_CTRL_ENABLE	BIT(0)
 
+/* Magic value to enable writes on jz4780 */
+#define JZ_RTC_WENR_MAGIC	0xA55A
+
+enum jz4740_rtc_type {
+	ID_JZ4740,
+	ID_JZ4780,
+};
+
 struct jz4740_rtc {
 	void __iomem *base;
+	enum jz4740_rtc_type type;
 
 	struct rtc_device *rtc;
 
@@ -64,11 +77,33 @@ static int jz4740_rtc_wait_write_ready(struct jz4740_rtc *rtc)
 	return timeout ? 0 : -EIO;
 }
 
+static inline int jz4780_rtc_enable_write(struct jz4740_rtc *rtc)
+{
+	uint32_t ctrl;
+	int ret, timeout = 1000;
+
+	ret = jz4740_rtc_wait_write_ready(rtc);
+	if (ret != 0)
+		return ret;
+
+	writel(JZ_RTC_WENR_MAGIC, rtc->base + JZ_REG_RTC_WENR);
+
+	do {
+		ctrl = readl(rtc->base + JZ_REG_RTC_WENR);
+	} while (!(ctrl & JZ_RTC_WENR_WEN) && --timeout);
+
+	return timeout ? 0 : -EIO;
+}
+
 static inline int jz4740_rtc_reg_write(struct jz4740_rtc *rtc, size_t reg,
 	uint32_t val)
 {
-	int ret;
-	ret = jz4740_rtc_wait_write_ready(rtc);
+	int ret = 0;
+
+	if (rtc->type >= ID_JZ4780)
+		ret = jz4780_rtc_enable_write(rtc);
+	if (ret == 0)
+		ret = jz4740_rtc_wait_write_ready(rtc);
 	if (ret == 0)
 		writel(val, rtc->base + reg);
 
@@ -216,11 +251,14 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 	struct jz4740_rtc *rtc;
 	uint32_t scratchpad;
 	struct resource *mem;
+	const struct platform_device_id *id = platform_get_device_id(pdev);
 
 	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
+	rtc->type = id->driver_data;
+
 	rtc->irq = platform_get_irq(pdev, 0);
 	if (rtc->irq < 0) {
 		dev_err(&pdev->dev, "Failed to get platform irq\n");
@@ -295,12 +333,20 @@ static const struct dev_pm_ops jz4740_pm_ops = {
 #define JZ4740_RTC_PM_OPS NULL
 #endif  /* CONFIG_PM */
 
+static const struct platform_device_id jz4740_rtc_ids[] = {
+	{"jz4740-rtc", ID_JZ4740},
+	{"jz4780-rtc", ID_JZ4780},
+	{}
+};
+MODULE_DEVICE_TABLE(platform, jz4740_rtc_ids);
+
 static struct platform_driver jz4740_rtc_driver = {
 	.probe	 = jz4740_rtc_probe,
 	.driver	 = {
 		.name  = "jz4740-rtc",
 		.pm    = JZ4740_RTC_PM_OPS,
 	},
+	.id_table = jz4740_rtc_ids,
 };
 
 module_platform_driver(jz4740_rtc_driver);
-- 
2.7.0

[rtc-linux] [PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/Kconfig      |  6 +++---
 drivers/rtc/rtc-jz4740.c | 50 ++++++++++++++++++++++++++++++++++++++++++++++--
 2 files changed, 51 insertions(+), 5 deletions(-)

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index e593c55..b322f08 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1494,10 +1494,10 @@ config RTC_DRV_MPC5121
 
 config RTC_DRV_JZ4740
 	tristate "Ingenic JZ4740 SoC"
-	depends on MACH_JZ4740 || COMPILE_TEST
+	depends on MACH_INGENIC || COMPILE_TEST
 	help
-	  If you say yes here you get support for the Ingenic JZ4740 SoC RTC
-	  controller.
+	  If you say yes here you get support for the Ingenic JZ47xx SoCs RTC
+	  controllers.
 
 	  This driver can also be buillt as a module. If so, the module
 	  will be called rtc-jz4740.
diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index b2bcfc0..47617bd 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -29,6 +29,10 @@
 #define JZ_REG_RTC_HIBERNATE	0x20
 #define JZ_REG_RTC_SCRATCHPAD	0x34
 
+/* The following are present on the jz4780 */
+#define JZ_REG_RTC_WENR	0x3C
+#define JZ_RTC_WENR_WEN	BIT(31)
+
 #define JZ_RTC_CTRL_WRDY	BIT(7)
 #define JZ_RTC_CTRL_1HZ		BIT(6)
 #define JZ_RTC_CTRL_1HZ_IRQ	BIT(5)
@@ -37,8 +41,17 @@
 #define JZ_RTC_CTRL_AE		BIT(2)
 #define JZ_RTC_CTRL_ENABLE	BIT(0)
 
+/* Magic value to enable writes on jz4780 */
+#define JZ_RTC_WENR_MAGIC	0xA55A
+
+enum jz4740_rtc_type {
+	ID_JZ4740,
+	ID_JZ4780,
+};
+
 struct jz4740_rtc {
 	void __iomem *base;
+	enum jz4740_rtc_type type;
 
 	struct rtc_device *rtc;
 
@@ -64,11 +77,33 @@ static int jz4740_rtc_wait_write_ready(struct jz4740_rtc *rtc)
 	return timeout ? 0 : -EIO;
 }
 
+static inline int jz4780_rtc_enable_write(struct jz4740_rtc *rtc)
+{
+	uint32_t ctrl;
+	int ret, timeout = 1000;
+
+	ret = jz4740_rtc_wait_write_ready(rtc);
+	if (ret != 0)
+		return ret;
+
+	writel(JZ_RTC_WENR_MAGIC, rtc->base + JZ_REG_RTC_WENR);
+
+	do {
+		ctrl = readl(rtc->base + JZ_REG_RTC_WENR);
+	} while (!(ctrl & JZ_RTC_WENR_WEN) && --timeout);
+
+	return timeout ? 0 : -EIO;
+}
+
 static inline int jz4740_rtc_reg_write(struct jz4740_rtc *rtc, size_t reg,
 	uint32_t val)
 {
-	int ret;
-	ret = jz4740_rtc_wait_write_ready(rtc);
+	int ret = 0;
+
+	if (rtc->type >= ID_JZ4780)
+		ret = jz4780_rtc_enable_write(rtc);
+	if (ret == 0)
+		ret = jz4740_rtc_wait_write_ready(rtc);
 	if (ret == 0)
 		writel(val, rtc->base + reg);
 
@@ -216,11 +251,14 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 	struct jz4740_rtc *rtc;
 	uint32_t scratchpad;
 	struct resource *mem;
+	const struct platform_device_id *id = platform_get_device_id(pdev);
 
 	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
+	rtc->type = id->driver_data;
+
 	rtc->irq = platform_get_irq(pdev, 0);
 	if (rtc->irq < 0) {
 		dev_err(&pdev->dev, "Failed to get platform irq\n");
@@ -295,12 +333,20 @@ static const struct dev_pm_ops jz4740_pm_ops = {
 #define JZ4740_RTC_PM_OPS NULL
 #endif  /* CONFIG_PM */
 
+static const struct platform_device_id jz4740_rtc_ids[] = {
+	{"jz4740-rtc", ID_JZ4740},
+	{"jz4780-rtc", ID_JZ4780},
+	{}
+};
+MODULE_DEVICE_TABLE(platform, jz4740_rtc_ids);
+
 static struct platform_driver jz4740_rtc_driver = {
 	.probe	 = jz4740_rtc_probe,
 	.driver	 = {
 		.name  = "jz4740-rtc",
 		.pm    = JZ4740_RTC_PM_OPS,
 	},
+	.id_table = jz4740_rtc_ids,
 };
 
 module_platform_driver(jz4740_rtc_driver);
-- 
2.7.0

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt

diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
new file mode 100644
index 0000000..71e4ad0
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
@@ -0,0 +1,38 @@
+JZ4740 and similar SoCs real-time clock driver
+
+Required properties:
+
+- compatible: One of:
+  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
+  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
+- reg: Address range of rtc register set
+- interrupts: IRQ number for the alarm interrupt
+- interrupt-parent: phandle of the interrupt controller
+- clocks: phandle to the "rtc" clock
+- clock-names: must be "rtc"
+
+Optional properties:
+- system-power-controller: To use this component as the
+  system power controller
+- reset-pin-assert-time: Reset pin low-level assertion time
+  after wakeup (default 60ms; range 0-125ms if RTC clock at 
+  32 kHz)
+- min-wakeup-pin-assert-time: Minimum wakeup pin assertion time
+  (default 100ms; range 0-2s if RTC clock at 32 kHz)
+
+Example:
+
+rtc@10003000 {
+	compatible = "ingenic,jz4740-rtc";
+	reg = <0x10003000 0x3F>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <32>;
+
+	clocks = <&rtc_clock>;
+	clock-names = "rtc";
+
+	system-power-controller;
+	reset-pin-assert-time = <60>;
+	min-wakeup-pin-assert-time = <100>;
+};
-- 
2.7.0

[rtc-linux] [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt

diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
new file mode 100644
index 0000000..71e4ad0
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
@@ -0,0 +1,38 @@
+JZ4740 and similar SoCs real-time clock driver
+
+Required properties:
+
+- compatible: One of:
+  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
+  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
+- reg: Address range of rtc register set
+- interrupts: IRQ number for the alarm interrupt
+- interrupt-parent: phandle of the interrupt controller
+- clocks: phandle to the "rtc" clock
+- clock-names: must be "rtc"
+
+Optional properties:
+- system-power-controller: To use this component as the
+  system power controller
+- reset-pin-assert-time: Reset pin low-level assertion time
+  after wakeup (default 60ms; range 0-125ms if RTC clock at 
+  32 kHz)
+- min-wakeup-pin-assert-time: Minimum wakeup pin assertion time
+  (default 100ms; range 0-2s if RTC clock at 32 kHz)
+
+Example:
+
+rtc@10003000 {
+	compatible = "ingenic,jz4740-rtc";
+	reg = <0x10003000 0x3F>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <32>;
+
+	clocks = <&rtc_clock>;
+	clock-names = "rtc";
+
+	system-power-controller;
+	reset-pin-assert-time = <60>;
+	min-wakeup-pin-assert-time = <100>;
+};
-- 
2.7.0

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index 47617bd..3914b1c 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -17,6 +17,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/rtc.h>
 #include <linux/slab.h>
@@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
 
+static const struct of_device_id jz4740_rtc_of_match[] = {
+	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
+	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, jz4740_rtc_of_match);
+
 static int jz4740_rtc_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -252,12 +260,17 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 	uint32_t scratchpad;
 	struct resource *mem;
 	const struct platform_device_id *id = platform_get_device_id(pdev);
+	const struct of_device_id *of_id = of_match_device(
+			jz4740_rtc_of_match, &pdev->dev);
 
 	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
-	rtc->type = id->driver_data;
+	if (of_id)
+		rtc->type = (enum jz4740_rtc_type) of_id->data;
+	else
+		rtc->type = id->driver_data;
 
 	rtc->irq = platform_get_irq(pdev, 0);
 	if (rtc->irq < 0) {
@@ -345,6 +358,7 @@ static struct platform_driver jz4740_rtc_driver = {
 	.driver	 = {
 		.name  = "jz4740-rtc",
 		.pm    = JZ4740_RTC_PM_OPS,
+		.of_match_table = of_match_ptr(jz4740_rtc_of_match),
 	},
 	.id_table = jz4740_rtc_ids,
 };
-- 
2.7.0

[rtc-linux] [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index 47617bd..3914b1c 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -17,6 +17,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/rtc.h>
 #include <linux/slab.h>
@@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
 
+static const struct of_device_id jz4740_rtc_of_match[] = {
+	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
+	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, jz4740_rtc_of_match);
+
 static int jz4740_rtc_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -252,12 +260,17 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 	uint32_t scratchpad;
 	struct resource *mem;
 	const struct platform_device_id *id = platform_get_device_id(pdev);
+	const struct of_device_id *of_id = of_match_device(
+			jz4740_rtc_of_match, &pdev->dev);
 
 	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
-	rtc->type = id->driver_data;
+	if (of_id)
+		rtc->type = (enum jz4740_rtc_type) of_id->data;
+	else
+		rtc->type = id->driver_data;
 
 	rtc->irq = platform_get_irq(pdev, 0);
 	if (rtc->irq < 0) {
@@ -345,6 +358,7 @@ static struct platform_driver jz4740_rtc_driver = {
 	.driver	 = {
 		.name  = "jz4740-rtc",
 		.pm    = JZ4740_RTC_PM_OPS,
+		.of_match_table = of_match_ptr(jz4740_rtc_of_match),
 	},
 	.id_table = jz4740_rtc_ids,
 };
-- 
2.7.0

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH 4/5] rtc: jz4740_rtc: Add support for acting as the system power controller

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/rtc-jz4740.c | 77 ++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index 3914b1c..f53cfd6 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -14,11 +14,13 @@
  *
  */
 
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reboot.h>
 #include <linux/rtc.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
@@ -28,6 +30,8 @@
 #define JZ_REG_RTC_SEC_ALARM	0x08
 #define JZ_REG_RTC_REGULATOR	0x0C
 #define JZ_REG_RTC_HIBERNATE	0x20
+#define JZ_REG_RTC_WAKEUP_FILTER	0x24
+#define JZ_REG_RTC_RESET_COUNTER	0x28
 #define JZ_REG_RTC_SCRATCHPAD	0x34
 
 /* The following are present on the jz4780 */
@@ -45,6 +49,9 @@
 /* Magic value to enable writes on jz4780 */
 #define JZ_RTC_WENR_MAGIC	0xA55A
 
+#define JZ_RTC_WAKEUP_FILTER_MASK	0x0000FFE0
+#define JZ_RTC_RESET_COUNTER_MASK	0x00000FE0
+
 enum jz4740_rtc_type {
 	ID_JZ4740,
 	ID_JZ4780,
@@ -59,8 +66,13 @@ struct jz4740_rtc {
 	int irq;
 
 	spinlock_t lock;
+
+	unsigned int min_wakeup_pin_assert_time;
+	unsigned int reset_pin_assert_time;
 };
 
+static struct device *dev_for_power_off;
+
 static inline uint32_t jz4740_rtc_reg_read(struct jz4740_rtc *rtc, size_t reg)
 {
 	return readl(rtc->base + reg);
@@ -246,6 +258,49 @@ void jz4740_rtc_poweroff(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
 
+static void jz4740_rtc_power_off(void)
+{
+	struct jz4740_rtc *rtc = dev_get_drvdata(dev_for_power_off);
+	unsigned long wakeup_filter_ticks;
+	unsigned long reset_counter_ticks;
+	struct clk *rtc_clk;
+	unsigned long rtc_rate;
+
+	rtc_clk = clk_get(dev_for_power_off, "rtc");
+	if (IS_ERR(rtc_clk))
+		panic("unable to get RTC clock");
+	rtc_rate = clk_get_rate(rtc_clk);
+	clk_put(rtc_clk);
+
+	/*
+	 * Set minimum wakeup pin assertion time: 100 ms.
+	 * Range is 0 to 2 sec if RTC is clocked at 32 kHz.
+	 */
+	wakeup_filter_ticks =
+		(rtc->min_wakeup_pin_assert_time * rtc_rate) / 1000;
+	if (wakeup_filter_ticks < JZ_RTC_WAKEUP_FILTER_MASK)
+		wakeup_filter_ticks &= JZ_RTC_WAKEUP_FILTER_MASK;
+	else
+		wakeup_filter_ticks = JZ_RTC_WAKEUP_FILTER_MASK;
+	jz4740_rtc_reg_write(rtc,
+			JZ_REG_RTC_WAKEUP_FILTER, wakeup_filter_ticks);
+
+	/*
+	 * Set reset pin low-level assertion time after wakeup: 60 ms.
+	 * Range is 0 to 125 ms if RTC is clocked at 32 kHz.
+	 */
+	reset_counter_ticks = (rtc->reset_pin_assert_time * rtc_rate) / 1000;
+	if (reset_counter_ticks < JZ_RTC_RESET_COUNTER_MASK)
+		reset_counter_ticks &= JZ_RTC_RESET_COUNTER_MASK;
+	else
+		reset_counter_ticks = JZ_RTC_RESET_COUNTER_MASK;
+	jz4740_rtc_reg_write(rtc,
+			JZ_REG_RTC_RESET_COUNTER, reset_counter_ticks);
+
+	jz4740_rtc_poweroff(dev_for_power_off);
+	machine_halt();
+}
+
 static const struct of_device_id jz4740_rtc_of_match[] = {
 	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
 	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
@@ -314,6 +369,28 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (of_device_is_system_power_controller(pdev->dev.of_node)) {
+		if (!pm_power_off) {
+			/* Default: 60ms */
+			rtc->reset_pin_assert_time = 60;
+			device_property_read_u32(&pdev->dev,
+					"reset-pin-assert-time",
+					&rtc->reset_pin_assert_time);
+
+			/* Default: 100ms */
+			rtc->min_wakeup_pin_assert_time = 100;
+			device_property_read_u32(&pdev->dev,
+					"min-wakeup-pin-assert-time",
+					&rtc->min_wakeup_pin_assert_time);
+
+			dev_for_power_off = &pdev->dev;
+			pm_power_off = jz4740_rtc_power_off;
+		} else {
+			dev_err(&pdev->dev,
+					"Poweroff handler already present!\n");
+		}
+	}
+
 	return 0;
 }
 
-- 
2.7.0

[rtc-linux] [PATCH 4/5] rtc: jz4740_rtc: Add support for acting as the system power controller

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 drivers/rtc/rtc-jz4740.c | 77 ++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
index 3914b1c..f53cfd6 100644
--- a/drivers/rtc/rtc-jz4740.c
+++ b/drivers/rtc/rtc-jz4740.c
@@ -14,11 +14,13 @@
  *
  */
 
+#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/reboot.h>
 #include <linux/rtc.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
@@ -28,6 +30,8 @@
 #define JZ_REG_RTC_SEC_ALARM	0x08
 #define JZ_REG_RTC_REGULATOR	0x0C
 #define JZ_REG_RTC_HIBERNATE	0x20
+#define JZ_REG_RTC_WAKEUP_FILTER	0x24
+#define JZ_REG_RTC_RESET_COUNTER	0x28
 #define JZ_REG_RTC_SCRATCHPAD	0x34
 
 /* The following are present on the jz4780 */
@@ -45,6 +49,9 @@
 /* Magic value to enable writes on jz4780 */
 #define JZ_RTC_WENR_MAGIC	0xA55A
 
+#define JZ_RTC_WAKEUP_FILTER_MASK	0x0000FFE0
+#define JZ_RTC_RESET_COUNTER_MASK	0x00000FE0
+
 enum jz4740_rtc_type {
 	ID_JZ4740,
 	ID_JZ4780,
@@ -59,8 +66,13 @@ struct jz4740_rtc {
 	int irq;
 
 	spinlock_t lock;
+
+	unsigned int min_wakeup_pin_assert_time;
+	unsigned int reset_pin_assert_time;
 };
 
+static struct device *dev_for_power_off;
+
 static inline uint32_t jz4740_rtc_reg_read(struct jz4740_rtc *rtc, size_t reg)
 {
 	return readl(rtc->base + reg);
@@ -246,6 +258,49 @@ void jz4740_rtc_poweroff(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
 
+static void jz4740_rtc_power_off(void)
+{
+	struct jz4740_rtc *rtc = dev_get_drvdata(dev_for_power_off);
+	unsigned long wakeup_filter_ticks;
+	unsigned long reset_counter_ticks;
+	struct clk *rtc_clk;
+	unsigned long rtc_rate;
+
+	rtc_clk = clk_get(dev_for_power_off, "rtc");
+	if (IS_ERR(rtc_clk))
+		panic("unable to get RTC clock");
+	rtc_rate = clk_get_rate(rtc_clk);
+	clk_put(rtc_clk);
+
+	/*
+	 * Set minimum wakeup pin assertion time: 100 ms.
+	 * Range is 0 to 2 sec if RTC is clocked at 32 kHz.
+	 */
+	wakeup_filter_ticks =
+		(rtc->min_wakeup_pin_assert_time * rtc_rate) / 1000;
+	if (wakeup_filter_ticks < JZ_RTC_WAKEUP_FILTER_MASK)
+		wakeup_filter_ticks &= JZ_RTC_WAKEUP_FILTER_MASK;
+	else
+		wakeup_filter_ticks = JZ_RTC_WAKEUP_FILTER_MASK;
+	jz4740_rtc_reg_write(rtc,
+			JZ_REG_RTC_WAKEUP_FILTER, wakeup_filter_ticks);
+
+	/*
+	 * Set reset pin low-level assertion time after wakeup: 60 ms.
+	 * Range is 0 to 125 ms if RTC is clocked at 32 kHz.
+	 */
+	reset_counter_ticks = (rtc->reset_pin_assert_time * rtc_rate) / 1000;
+	if (reset_counter_ticks < JZ_RTC_RESET_COUNTER_MASK)
+		reset_counter_ticks &= JZ_RTC_RESET_COUNTER_MASK;
+	else
+		reset_counter_ticks = JZ_RTC_RESET_COUNTER_MASK;
+	jz4740_rtc_reg_write(rtc,
+			JZ_REG_RTC_RESET_COUNTER, reset_counter_ticks);
+
+	jz4740_rtc_poweroff(dev_for_power_off);
+	machine_halt();
+}
+
 static const struct of_device_id jz4740_rtc_of_match[] = {
 	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
 	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
@@ -314,6 +369,28 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (of_device_is_system_power_controller(pdev->dev.of_node)) {
+		if (!pm_power_off) {
+			/* Default: 60ms */
+			rtc->reset_pin_assert_time = 60;
+			device_property_read_u32(&pdev->dev,
+					"reset-pin-assert-time",
+					&rtc->reset_pin_assert_time);
+
+			/* Default: 100ms */
+			rtc->min_wakeup_pin_assert_time = 100;
+			device_property_read_u32(&pdev->dev,
+					"min-wakeup-pin-assert-time",
+					&rtc->min_wakeup_pin_assert_time);
+
+			dev_for_power_off = &pdev->dev;
+			pm_power_off = jz4740_rtc_power_off;
+		} else {
+			dev_err(&pdev->dev,
+					"Poweroff handler already present!\n");
+		}
+	}
+
 	return 0;
 }
 
-- 
2.7.0

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
 arch/mips/jz4740/reset.c               | 64 ----------------------------------
 2 files changed, 2 insertions(+), 64 deletions(-)

diff --git a/arch/mips/boot/dts/ingenic/jz4740.dtsi b/arch/mips/boot/dts/ingenic/jz4740.dtsi
index 8b2437c..f2ddacb 100644
--- a/arch/mips/boot/dts/ingenic/jz4740.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4740.dtsi
@@ -32,6 +32,8 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
+
+		system-power-controller;
 	};
 
 	cgu: jz4740-cgu@10000000 {
diff --git a/arch/mips/jz4740/reset.c b/arch/mips/jz4740/reset.c
index 954e669..0a88b17 100644
--- a/arch/mips/jz4740/reset.c
+++ b/arch/mips/jz4740/reset.c
@@ -12,7 +12,6 @@
  *
  */
 
-#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/pm.h>
@@ -57,71 +56,8 @@ static void jz4740_restart(char *command)
 	jz4740_halt();
 }
 
-#define JZ_REG_RTC_CTRL			0x00
-#define JZ_REG_RTC_HIBERNATE		0x20
-#define JZ_REG_RTC_WAKEUP_FILTER	0x24
-#define JZ_REG_RTC_RESET_COUNTER	0x28
-
-#define JZ_RTC_CTRL_WRDY		BIT(7)
-#define JZ_RTC_WAKEUP_FILTER_MASK	0x0000FFE0
-#define JZ_RTC_RESET_COUNTER_MASK	0x00000FE0
-
-static inline void jz4740_rtc_wait_ready(void __iomem *rtc_base)
-{
-	uint32_t ctrl;
-
-	do {
-		ctrl = readl(rtc_base + JZ_REG_RTC_CTRL);
-	} while (!(ctrl & JZ_RTC_CTRL_WRDY));
-}
-
-static void jz4740_power_off(void)
-{
-	void __iomem *rtc_base = ioremap(JZ4740_RTC_BASE_ADDR, 0x38);
-	unsigned long wakeup_filter_ticks;
-	unsigned long reset_counter_ticks;
-	struct clk *rtc_clk;
-	unsigned long rtc_rate;
-
-	rtc_clk = clk_get(NULL, "rtc");
-	if (IS_ERR(rtc_clk))
-		panic("unable to get RTC clock");
-	rtc_rate = clk_get_rate(rtc_clk);
-	clk_put(rtc_clk);
-
-	/*
-	 * Set minimum wakeup pin assertion time: 100 ms.
-	 * Range is 0 to 2 sec if RTC is clocked at 32 kHz.
-	 */
-	wakeup_filter_ticks = (100 * rtc_rate) / 1000;
-	if (wakeup_filter_ticks < JZ_RTC_WAKEUP_FILTER_MASK)
-		wakeup_filter_ticks &= JZ_RTC_WAKEUP_FILTER_MASK;
-	else
-		wakeup_filter_ticks = JZ_RTC_WAKEUP_FILTER_MASK;
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(wakeup_filter_ticks, rtc_base + JZ_REG_RTC_WAKEUP_FILTER);
-
-	/*
-	 * Set reset pin low-level assertion time after wakeup: 60 ms.
-	 * Range is 0 to 125 ms if RTC is clocked at 32 kHz.
-	 */
-	reset_counter_ticks = (60 * rtc_rate) / 1000;
-	if (reset_counter_ticks < JZ_RTC_RESET_COUNTER_MASK)
-		reset_counter_ticks &= JZ_RTC_RESET_COUNTER_MASK;
-	else
-		reset_counter_ticks = JZ_RTC_RESET_COUNTER_MASK;
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(reset_counter_ticks, rtc_base + JZ_REG_RTC_RESET_COUNTER);
-
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(1, rtc_base + JZ_REG_RTC_HIBERNATE);
-
-	jz4740_halt();
-}
-
 void jz4740_reset_init(void)
 {
 	_machine_restart = jz4740_restart;
 	_machine_halt = jz4740_halt;
-	pm_power_off = jz4740_power_off;
 }
-- 
2.7.0

[rtc-linux] [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Paul Cercueil]

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
 arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
 arch/mips/jz4740/reset.c               | 64 ----------------------------------
 2 files changed, 2 insertions(+), 64 deletions(-)

diff --git a/arch/mips/boot/dts/ingenic/jz4740.dtsi b/arch/mips/boot/dts/ingenic/jz4740.dtsi
index 8b2437c..f2ddacb 100644
--- a/arch/mips/boot/dts/ingenic/jz4740.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4740.dtsi
@@ -32,6 +32,8 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
+
+		system-power-controller;
 	};
 
 	cgu: jz4740-cgu@10000000 {
diff --git a/arch/mips/jz4740/reset.c b/arch/mips/jz4740/reset.c
index 954e669..0a88b17 100644
--- a/arch/mips/jz4740/reset.c
+++ b/arch/mips/jz4740/reset.c
@@ -12,7 +12,6 @@
  *
  */
 
-#include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/pm.h>
@@ -57,71 +56,8 @@ static void jz4740_restart(char *command)
 	jz4740_halt();
 }
 
-#define JZ_REG_RTC_CTRL			0x00
-#define JZ_REG_RTC_HIBERNATE		0x20
-#define JZ_REG_RTC_WAKEUP_FILTER	0x24
-#define JZ_REG_RTC_RESET_COUNTER	0x28
-
-#define JZ_RTC_CTRL_WRDY		BIT(7)
-#define JZ_RTC_WAKEUP_FILTER_MASK	0x0000FFE0
-#define JZ_RTC_RESET_COUNTER_MASK	0x00000FE0
-
-static inline void jz4740_rtc_wait_ready(void __iomem *rtc_base)
-{
-	uint32_t ctrl;
-
-	do {
-		ctrl = readl(rtc_base + JZ_REG_RTC_CTRL);
-	} while (!(ctrl & JZ_RTC_CTRL_WRDY));
-}
-
-static void jz4740_power_off(void)
-{
-	void __iomem *rtc_base = ioremap(JZ4740_RTC_BASE_ADDR, 0x38);
-	unsigned long wakeup_filter_ticks;
-	unsigned long reset_counter_ticks;
-	struct clk *rtc_clk;
-	unsigned long rtc_rate;
-
-	rtc_clk = clk_get(NULL, "rtc");
-	if (IS_ERR(rtc_clk))
-		panic("unable to get RTC clock");
-	rtc_rate = clk_get_rate(rtc_clk);
-	clk_put(rtc_clk);
-
-	/*
-	 * Set minimum wakeup pin assertion time: 100 ms.
-	 * Range is 0 to 2 sec if RTC is clocked at 32 kHz.
-	 */
-	wakeup_filter_ticks = (100 * rtc_rate) / 1000;
-	if (wakeup_filter_ticks < JZ_RTC_WAKEUP_FILTER_MASK)
-		wakeup_filter_ticks &= JZ_RTC_WAKEUP_FILTER_MASK;
-	else
-		wakeup_filter_ticks = JZ_RTC_WAKEUP_FILTER_MASK;
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(wakeup_filter_ticks, rtc_base + JZ_REG_RTC_WAKEUP_FILTER);
-
-	/*
-	 * Set reset pin low-level assertion time after wakeup: 60 ms.
-	 * Range is 0 to 125 ms if RTC is clocked at 32 kHz.
-	 */
-	reset_counter_ticks = (60 * rtc_rate) / 1000;
-	if (reset_counter_ticks < JZ_RTC_RESET_COUNTER_MASK)
-		reset_counter_ticks &= JZ_RTC_RESET_COUNTER_MASK;
-	else
-		reset_counter_ticks = JZ_RTC_RESET_COUNTER_MASK;
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(reset_counter_ticks, rtc_base + JZ_REG_RTC_RESET_COUNTER);
-
-	jz4740_rtc_wait_ready(rtc_base);
-	writel(1, rtc_base + JZ_REG_RTC_HIBERNATE);
-
-	jz4740_halt();
-}
-
 void jz4740_reset_init(void)
 {
 	_machine_restart = jz4740_restart;
 	_machine_halt = jz4740_halt;
-	pm_power_off = jz4740_power_off;
 }
-- 
2.7.0

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Sergei Shtylyov]

Hello.

On 3/6/2016 1:38 AM, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>   .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>   1 file changed, 38 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
>
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller

    This is never a required property, it can be inherited from the parent node.

[...]

MBR, Sergei

[rtc-linux] Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Sergei Shtylyov]

Hello.

On 3/6/2016 1:38 AM, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>   .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>   1 file changed, 38 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
>
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller

    This is never a required property, it can be inherited from the parent node.

[...]

MBR, Sergei

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Sergei Shtylyov]

Hello.

On 3/6/2016 1:38 AM, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>   .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>   1 file changed, 38 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
>
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller

    This is never a required property, it can be inherited from the parent node.

[...]

MBR, Sergei

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Ralf Baechle]

On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
>  arch/mips/jz4740/reset.c               | 64 ----------------------------------

Acked-by: Ralf Baechle <ralf@linux-mips.org>

Feel free to funnel this patch upstream through the RTC tree.  Or I can
carry the whole series, just lemme know.

  Ralf

[rtc-linux] Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Ralf Baechle]

On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
>  arch/mips/jz4740/reset.c               | 64 ----------------------------------

Acked-by: Ralf Baechle <ralf@linux-mips.org>

Feel free to funnel this patch upstream through the RTC tree.  Or I can
carry the whole series, just lemme know.

  Ralf

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Ralf Baechle]

On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:

> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
>  arch/mips/jz4740/reset.c               | 64 ----------------------------------

Acked-by: Ralf Baechle <ralf-6z/3iImG2C8G8FEW9MqTrA@public.gmane.org>

Feel free to funnel this patch upstream through the RTC tree.  Or I can
carry the whole series, just lemme know.

  Ralf
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Rob Herring]

On Sat, Mar 05, 2016 at 11:38:48PM +0100, Paul Cercueil wrote:
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller

> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 
> +  32 kHz)
> +- min-wakeup-pin-assert-time: Minimum wakeup pin assertion time
> +  (default 100ms; range 0-2s if RTC clock at 32 kHz)

Please append units on these (-msec).

> +
> +Example:
> +
> +rtc@10003000 {
> +	compatible = "ingenic,jz4740-rtc";
> +	reg = <0x10003000 0x3F>;
> +
> +	interrupt-parent = <&intc>;
> +	interrupts = <32>;
> +
> +	clocks = <&rtc_clock>;
> +	clock-names = "rtc";
> +
> +	system-power-controller;
> +	reset-pin-assert-time = <60>;
> +	min-wakeup-pin-assert-time = <100>;
> +};
> -- 
> 2.7.0
> 

[rtc-linux] Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Rob Herring]

On Sat, Mar 05, 2016 at 11:38:48PM +0100, Paul Cercueil wrote:
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller

> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 
> +  32 kHz)
> +- min-wakeup-pin-assert-time: Minimum wakeup pin assertion time
> +  (default 100ms; range 0-2s if RTC clock at 32 kHz)

Please append units on these (-msec).

> +
> +Example:
> +
> +rtc@10003000 {
> +	compatible = "ingenic,jz4740-rtc";
> +	reg = <0x10003000 0x3F>;
> +
> +	interrupt-parent = <&intc>;
> +	interrupts = <32>;
> +
> +	clocks = <&rtc_clock>;
> +	clock-names = "rtc";
> +
> +	system-power-controller;
> +	reset-pin-assert-time = <60>;
> +	min-wakeup-pin-assert-time = <100>;
> +};
> -- 
> 2.7.0
> 

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Rob Herring]

On Sat, Mar 05, 2016 at 11:38:48PM +0100, Paul Cercueil wrote:
> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller

> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 
> +  32 kHz)
> +- min-wakeup-pin-assert-time: Minimum wakeup pin assertion time
> +  (default 100ms; range 0-2s if RTC clock at 32 kHz)

Please append units on these (-msec).

> +
> +Example:
> +
> +rtc@10003000 {
> +	compatible = "ingenic,jz4740-rtc";
> +	reg = <0x10003000 0x3F>;
> +
> +	interrupt-parent = <&intc>;
> +	interrupts = <32>;
> +
> +	clocks = <&rtc_clock>;
> +	clock-names = "rtc";
> +
> +	system-power-controller;
> +	reset-pin-assert-time = <60>;
> +	min-wakeup-pin-assert-time = <100>;
> +};
> -- 
> 2.7.0
> 
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[Alexandre Belloni]

Please, always include a commit message, even if it is short.

On 05/03/2016 at 23:38:47 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  drivers/rtc/Kconfig      |  6 +++---
>  drivers/rtc/rtc-jz4740.c | 50 ++++++++++++++++++++++++++++++++++++++++++++++--
>  2 files changed, 51 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
> index e593c55..b322f08 100644
> --- a/drivers/rtc/Kconfig
> +++ b/drivers/rtc/Kconfig
> @@ -1494,10 +1494,10 @@ config RTC_DRV_MPC5121
>  
>  config RTC_DRV_JZ4740
>  	tristate "Ingenic JZ4740 SoC"
> -	depends on MACH_JZ4740 || COMPILE_TEST
> +	depends on MACH_INGENIC || COMPILE_TEST
>  	help
> -	  If you say yes here you get support for the Ingenic JZ4740 SoC RTC
> -	  controller.
> +	  If you say yes here you get support for the Ingenic JZ47xx SoCs RTC
> +	  controllers.
>  
>  	  This driver can also be buillt as a module. If so, the module
>  	  will be called rtc-jz4740.
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index b2bcfc0..47617bd 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -29,6 +29,10 @@
>  #define JZ_REG_RTC_HIBERNATE	0x20
>  #define JZ_REG_RTC_SCRATCHPAD	0x34
>  
> +/* The following are present on the jz4780 */
> +#define JZ_REG_RTC_WENR	0x3C
> +#define JZ_RTC_WENR_WEN	BIT(31)
> +
>  #define JZ_RTC_CTRL_WRDY	BIT(7)
>  #define JZ_RTC_CTRL_1HZ		BIT(6)
>  #define JZ_RTC_CTRL_1HZ_IRQ	BIT(5)
> @@ -37,8 +41,17 @@
>  #define JZ_RTC_CTRL_AE		BIT(2)
>  #define JZ_RTC_CTRL_ENABLE	BIT(0)
>  
> +/* Magic value to enable writes on jz4780 */
> +#define JZ_RTC_WENR_MAGIC	0xA55A
> +
> +enum jz4740_rtc_type {
> +	ID_JZ4740,
> +	ID_JZ4780,
> +};
> +
>  struct jz4740_rtc {
>  	void __iomem *base;
> +	enum jz4740_rtc_type type;
>  
>  	struct rtc_device *rtc;
>  
> @@ -64,11 +77,33 @@ static int jz4740_rtc_wait_write_ready(struct jz4740_rtc *rtc)
>  	return timeout ? 0 : -EIO;
>  }
>  
> +static inline int jz4780_rtc_enable_write(struct jz4740_rtc *rtc)
> +{
> +	uint32_t ctrl;
> +	int ret, timeout = 1000;
> +
> +	ret = jz4740_rtc_wait_write_ready(rtc);
> +	if (ret != 0)
> +		return ret;
> +
> +	writel(JZ_RTC_WENR_MAGIC, rtc->base + JZ_REG_RTC_WENR);
> +
> +	do {
> +		ctrl = readl(rtc->base + JZ_REG_RTC_WENR);
> +	} while (!(ctrl & JZ_RTC_WENR_WEN) && --timeout);
> +
> +	return timeout ? 0 : -EIO;
> +}
> +
>  static inline int jz4740_rtc_reg_write(struct jz4740_rtc *rtc, size_t reg,
>  	uint32_t val)
>  {
> -	int ret;
> -	ret = jz4740_rtc_wait_write_ready(rtc);
> +	int ret = 0;
> +
> +	if (rtc->type >= ID_JZ4780)
> +		ret = jz4780_rtc_enable_write(rtc);
> +	if (ret == 0)
> +		ret = jz4740_rtc_wait_write_ready(rtc);
>  	if (ret == 0)
>  		writel(val, rtc->base + reg);
>  
> @@ -216,11 +251,14 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	struct jz4740_rtc *rtc;
>  	uint32_t scratchpad;
>  	struct resource *mem;
> +	const struct platform_device_id *id = platform_get_device_id(pdev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> +	rtc->type = id->driver_data;
> +
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
>  		dev_err(&pdev->dev, "Failed to get platform irq\n");
> @@ -295,12 +333,20 @@ static const struct dev_pm_ops jz4740_pm_ops = {
>  #define JZ4740_RTC_PM_OPS NULL
>  #endif  /* CONFIG_PM */
>  
> +static const struct platform_device_id jz4740_rtc_ids[] = {
> +	{"jz4740-rtc", ID_JZ4740},
> +	{"jz4780-rtc", ID_JZ4780},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(platform, jz4740_rtc_ids);
> +
>  static struct platform_driver jz4740_rtc_driver = {
>  	.probe	 = jz4740_rtc_probe,
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
>  	},
> +	.id_table = jz4740_rtc_ids,
>  };
>  
>  module_platform_driver(jz4740_rtc_driver);
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[Alexandre Belloni]

Please, always include a commit message, even if it is short.

On 05/03/2016 at 23:38:47 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  drivers/rtc/Kconfig      |  6 +++---
>  drivers/rtc/rtc-jz4740.c | 50 ++++++++++++++++++++++++++++++++++++++++++++++--
>  2 files changed, 51 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
> index e593c55..b322f08 100644
> --- a/drivers/rtc/Kconfig
> +++ b/drivers/rtc/Kconfig
> @@ -1494,10 +1494,10 @@ config RTC_DRV_MPC5121
>  
>  config RTC_DRV_JZ4740
>  	tristate "Ingenic JZ4740 SoC"
> -	depends on MACH_JZ4740 || COMPILE_TEST
> +	depends on MACH_INGENIC || COMPILE_TEST
>  	help
> -	  If you say yes here you get support for the Ingenic JZ4740 SoC RTC
> -	  controller.
> +	  If you say yes here you get support for the Ingenic JZ47xx SoCs RTC
> +	  controllers.
>  
>  	  This driver can also be buillt as a module. If so, the module
>  	  will be called rtc-jz4740.
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index b2bcfc0..47617bd 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -29,6 +29,10 @@
>  #define JZ_REG_RTC_HIBERNATE	0x20
>  #define JZ_REG_RTC_SCRATCHPAD	0x34
>  
> +/* The following are present on the jz4780 */
> +#define JZ_REG_RTC_WENR	0x3C
> +#define JZ_RTC_WENR_WEN	BIT(31)
> +
>  #define JZ_RTC_CTRL_WRDY	BIT(7)
>  #define JZ_RTC_CTRL_1HZ		BIT(6)
>  #define JZ_RTC_CTRL_1HZ_IRQ	BIT(5)
> @@ -37,8 +41,17 @@
>  #define JZ_RTC_CTRL_AE		BIT(2)
>  #define JZ_RTC_CTRL_ENABLE	BIT(0)
>  
> +/* Magic value to enable writes on jz4780 */
> +#define JZ_RTC_WENR_MAGIC	0xA55A
> +
> +enum jz4740_rtc_type {
> +	ID_JZ4740,
> +	ID_JZ4780,
> +};
> +
>  struct jz4740_rtc {
>  	void __iomem *base;
> +	enum jz4740_rtc_type type;
>  
>  	struct rtc_device *rtc;
>  
> @@ -64,11 +77,33 @@ static int jz4740_rtc_wait_write_ready(struct jz4740_rtc *rtc)
>  	return timeout ? 0 : -EIO;
>  }
>  
> +static inline int jz4780_rtc_enable_write(struct jz4740_rtc *rtc)
> +{
> +	uint32_t ctrl;
> +	int ret, timeout = 1000;
> +
> +	ret = jz4740_rtc_wait_write_ready(rtc);
> +	if (ret != 0)
> +		return ret;
> +
> +	writel(JZ_RTC_WENR_MAGIC, rtc->base + JZ_REG_RTC_WENR);
> +
> +	do {
> +		ctrl = readl(rtc->base + JZ_REG_RTC_WENR);
> +	} while (!(ctrl & JZ_RTC_WENR_WEN) && --timeout);
> +
> +	return timeout ? 0 : -EIO;
> +}
> +
>  static inline int jz4740_rtc_reg_write(struct jz4740_rtc *rtc, size_t reg,
>  	uint32_t val)
>  {
> -	int ret;
> -	ret = jz4740_rtc_wait_write_ready(rtc);
> +	int ret = 0;
> +
> +	if (rtc->type >= ID_JZ4780)
> +		ret = jz4780_rtc_enable_write(rtc);
> +	if (ret == 0)
> +		ret = jz4740_rtc_wait_write_ready(rtc);
>  	if (ret == 0)
>  		writel(val, rtc->base + reg);
>  
> @@ -216,11 +251,14 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	struct jz4740_rtc *rtc;
>  	uint32_t scratchpad;
>  	struct resource *mem;
> +	const struct platform_device_id *id = platform_get_device_id(pdev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> +	rtc->type = id->driver_data;
> +
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
>  		dev_err(&pdev->dev, "Failed to get platform irq\n");
> @@ -295,12 +333,20 @@ static const struct dev_pm_ops jz4740_pm_ops = {
>  #define JZ4740_RTC_PM_OPS NULL
>  #endif  /* CONFIG_PM */
>  
> +static const struct platform_device_id jz4740_rtc_ids[] = {
> +	{"jz4740-rtc", ID_JZ4740},
> +	{"jz4780-rtc", ID_JZ4780},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(platform, jz4740_rtc_ids);
> +
>  static struct platform_driver jz4740_rtc_driver = {
>  	.probe	 = jz4740_rtc_probe,
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
>  	},
> +	.id_table = jz4740_rtc_ids,
>  };
>  
>  module_platform_driver(jz4740_rtc_driver);
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 1/5] rtc: rtc-jz4740: Add support for the RTC in the jz4780 SoC

[Alexandre Belloni]

Please, always include a commit message, even if it is short.

On 05/03/2016 at 23:38:47 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>  drivers/rtc/Kconfig      |  6 +++---
>  drivers/rtc/rtc-jz4740.c | 50 ++++++++++++++++++++++++++++++++++++++++++++++--
>  2 files changed, 51 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
> index e593c55..b322f08 100644
> --- a/drivers/rtc/Kconfig
> +++ b/drivers/rtc/Kconfig
> @@ -1494,10 +1494,10 @@ config RTC_DRV_MPC5121
>  
>  config RTC_DRV_JZ4740
>  	tristate "Ingenic JZ4740 SoC"
> -	depends on MACH_JZ4740 || COMPILE_TEST
> +	depends on MACH_INGENIC || COMPILE_TEST
>  	help
> -	  If you say yes here you get support for the Ingenic JZ4740 SoC RTC
> -	  controller.
> +	  If you say yes here you get support for the Ingenic JZ47xx SoCs RTC
> +	  controllers.
>  
>  	  This driver can also be buillt as a module. If so, the module
>  	  will be called rtc-jz4740.
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index b2bcfc0..47617bd 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -29,6 +29,10 @@
>  #define JZ_REG_RTC_HIBERNATE	0x20
>  #define JZ_REG_RTC_SCRATCHPAD	0x34
>  
> +/* The following are present on the jz4780 */
> +#define JZ_REG_RTC_WENR	0x3C
> +#define JZ_RTC_WENR_WEN	BIT(31)
> +
>  #define JZ_RTC_CTRL_WRDY	BIT(7)
>  #define JZ_RTC_CTRL_1HZ		BIT(6)
>  #define JZ_RTC_CTRL_1HZ_IRQ	BIT(5)
> @@ -37,8 +41,17 @@
>  #define JZ_RTC_CTRL_AE		BIT(2)
>  #define JZ_RTC_CTRL_ENABLE	BIT(0)
>  
> +/* Magic value to enable writes on jz4780 */
> +#define JZ_RTC_WENR_MAGIC	0xA55A
> +
> +enum jz4740_rtc_type {
> +	ID_JZ4740,
> +	ID_JZ4780,
> +};
> +
>  struct jz4740_rtc {
>  	void __iomem *base;
> +	enum jz4740_rtc_type type;
>  
>  	struct rtc_device *rtc;
>  
> @@ -64,11 +77,33 @@ static int jz4740_rtc_wait_write_ready(struct jz4740_rtc *rtc)
>  	return timeout ? 0 : -EIO;
>  }
>  
> +static inline int jz4780_rtc_enable_write(struct jz4740_rtc *rtc)
> +{
> +	uint32_t ctrl;
> +	int ret, timeout = 1000;
> +
> +	ret = jz4740_rtc_wait_write_ready(rtc);
> +	if (ret != 0)
> +		return ret;
> +
> +	writel(JZ_RTC_WENR_MAGIC, rtc->base + JZ_REG_RTC_WENR);
> +
> +	do {
> +		ctrl = readl(rtc->base + JZ_REG_RTC_WENR);
> +	} while (!(ctrl & JZ_RTC_WENR_WEN) && --timeout);
> +
> +	return timeout ? 0 : -EIO;
> +}
> +
>  static inline int jz4740_rtc_reg_write(struct jz4740_rtc *rtc, size_t reg,
>  	uint32_t val)
>  {
> -	int ret;
> -	ret = jz4740_rtc_wait_write_ready(rtc);
> +	int ret = 0;
> +
> +	if (rtc->type >= ID_JZ4780)
> +		ret = jz4780_rtc_enable_write(rtc);
> +	if (ret == 0)
> +		ret = jz4740_rtc_wait_write_ready(rtc);
>  	if (ret == 0)
>  		writel(val, rtc->base + reg);
>  
> @@ -216,11 +251,14 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	struct jz4740_rtc *rtc;
>  	uint32_t scratchpad;
>  	struct resource *mem;
> +	const struct platform_device_id *id = platform_get_device_id(pdev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> +	rtc->type = id->driver_data;
> +
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
>  		dev_err(&pdev->dev, "Failed to get platform irq\n");
> @@ -295,12 +333,20 @@ static const struct dev_pm_ops jz4740_pm_ops = {
>  #define JZ4740_RTC_PM_OPS NULL
>  #endif  /* CONFIG_PM */
>  
> +static const struct platform_device_id jz4740_rtc_ids[] = {
> +	{"jz4740-rtc", ID_JZ4740},
> +	{"jz4780-rtc", ID_JZ4780},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(platform, jz4740_rtc_ids);
> +
>  static struct platform_driver jz4740_rtc_driver = {
>  	.probe	 = jz4740_rtc_probe,
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
>  	},
> +	.id_table = jz4740_rtc_ids,
>  };
>  
>  module_platform_driver(jz4740_rtc_driver);
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Alexandre Belloni]

On 05/03/2016 at 23:38:48 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller
> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 

Trailing whitespace on that line.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Alexandre Belloni]

On 05/03/2016 at 23:38:48 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller
> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 

Trailing whitespace on that line.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 2/5] Documentation: dt: Add binding info for jz4740-rtc driver

[Alexandre Belloni]

On 05/03/2016 at 23:38:48 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>  .../devicetree/bindings/rtc/ingenic,jz4740-rtc.txt | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> 
> diff --git a/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> new file mode 100644
> index 0000000..71e4ad0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
> @@ -0,0 +1,38 @@
> +JZ4740 and similar SoCs real-time clock driver
> +
> +Required properties:
> +
> +- compatible: One of:
> +  - "ingenic,jz4740-rtc" - for use with the JZ4740 SoC
> +  - "ingenic,jz4780-rtc" - for use with the JZ4780 SoC
> +- reg: Address range of rtc register set
> +- interrupts: IRQ number for the alarm interrupt
> +- interrupt-parent: phandle of the interrupt controller
> +- clocks: phandle to the "rtc" clock
> +- clock-names: must be "rtc"
> +
> +Optional properties:
> +- system-power-controller: To use this component as the
> +  system power controller
> +- reset-pin-assert-time: Reset pin low-level assertion time
> +  after wakeup (default 60ms; range 0-125ms if RTC clock at 

Trailing whitespace on that line.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index 47617bd..3914b1c 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -17,6 +17,7 @@
>  #include <linux/io.h>
>  #include <linux/kernel.h>
>  #include <linux/module.h>
> +#include <linux/of_device.h>
>  #include <linux/platform_device.h>
>  #include <linux/rtc.h>
>  #include <linux/slab.h>
> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>  }
>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>  
> +static const struct of_device_id jz4740_rtc_of_match[] = {
> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },

ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
you have to add it there before using it.

Also, no space is necessary after the "(void *)" cast.

> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, jz4740_rtc_of_match);
> +
>  static int jz4740_rtc_probe(struct platform_device *pdev)
>  {
>  	int ret;
> @@ -252,12 +260,17 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	uint32_t scratchpad;
>  	struct resource *mem;
>  	const struct platform_device_id *id = platform_get_device_id(pdev);
> +	const struct of_device_id *of_id = of_match_device(
> +			jz4740_rtc_of_match, &pdev->dev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> -	rtc->type = id->driver_data;
> +	if (of_id)
> +		rtc->type = (enum jz4740_rtc_type) of_id->data;

No space after that cast either.

> +	else
> +		rtc->type = id->driver_data;
>  
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
> @@ -345,6 +358,7 @@ static struct platform_driver jz4740_rtc_driver = {
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
> +		.of_match_table = of_match_ptr(jz4740_rtc_of_match),
>  	},
>  	.id_table = jz4740_rtc_ids,
>  };
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index 47617bd..3914b1c 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -17,6 +17,7 @@
>  #include <linux/io.h>
>  #include <linux/kernel.h>
>  #include <linux/module.h>
> +#include <linux/of_device.h>
>  #include <linux/platform_device.h>
>  #include <linux/rtc.h>
>  #include <linux/slab.h>
> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>  }
>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>  
> +static const struct of_device_id jz4740_rtc_of_match[] = {
> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },

ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
you have to add it there before using it.

Also, no space is necessary after the "(void *)" cast.

> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, jz4740_rtc_of_match);
> +
>  static int jz4740_rtc_probe(struct platform_device *pdev)
>  {
>  	int ret;
> @@ -252,12 +260,17 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	uint32_t scratchpad;
>  	struct resource *mem;
>  	const struct platform_device_id *id = platform_get_device_id(pdev);
> +	const struct of_device_id *of_id = of_match_device(
> +			jz4740_rtc_of_match, &pdev->dev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> -	rtc->type = id->driver_data;
> +	if (of_id)
> +		rtc->type = (enum jz4740_rtc_type) of_id->data;

No space after that cast either.

> +	else
> +		rtc->type = id->driver_data;
>  
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
> @@ -345,6 +358,7 @@ static struct platform_driver jz4740_rtc_driver = {
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
> +		.of_match_table = of_match_ptr(jz4740_rtc_of_match),
>  	},
>  	.id_table = jz4740_rtc_ids,
>  };
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> ---
>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> index 47617bd..3914b1c 100644
> --- a/drivers/rtc/rtc-jz4740.c
> +++ b/drivers/rtc/rtc-jz4740.c
> @@ -17,6 +17,7 @@
>  #include <linux/io.h>
>  #include <linux/kernel.h>
>  #include <linux/module.h>
> +#include <linux/of_device.h>
>  #include <linux/platform_device.h>
>  #include <linux/rtc.h>
>  #include <linux/slab.h>
> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>  }
>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>  
> +static const struct of_device_id jz4740_rtc_of_match[] = {
> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },

ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
you have to add it there before using it.

Also, no space is necessary after the "(void *)" cast.

> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, jz4740_rtc_of_match);
> +
>  static int jz4740_rtc_probe(struct platform_device *pdev)
>  {
>  	int ret;
> @@ -252,12 +260,17 @@ static int jz4740_rtc_probe(struct platform_device *pdev)
>  	uint32_t scratchpad;
>  	struct resource *mem;
>  	const struct platform_device_id *id = platform_get_device_id(pdev);
> +	const struct of_device_id *of_id = of_match_device(
> +			jz4740_rtc_of_match, &pdev->dev);
>  
>  	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
>  	if (!rtc)
>  		return -ENOMEM;
>  
> -	rtc->type = id->driver_data;
> +	if (of_id)
> +		rtc->type = (enum jz4740_rtc_type) of_id->data;

No space after that cast either.

> +	else
> +		rtc->type = id->driver_data;
>  
>  	rtc->irq = platform_get_irq(pdev, 0);
>  	if (rtc->irq < 0) {
> @@ -345,6 +358,7 @@ static struct platform_driver jz4740_rtc_driver = {
>  	.driver	 = {
>  		.name  = "jz4740-rtc",
>  		.pm    = JZ4740_RTC_PM_OPS,
> +		.of_match_table = of_match_ptr(jz4740_rtc_of_match),
>  	},
>  	.id_table = jz4740_rtc_ids,
>  };
> -- 
> 2.7.0
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 4/5] rtc: jz4740_rtc: Add support for acting as the system power controller

[Alexandre Belloni]

On 05/03/2016 at 23:38:50 +0100, Paul Cercueil wrote :
> +	if (of_device_is_system_power_controller(pdev->dev.of_node)) {
> +		if (!pm_power_off) {
> +			/* Default: 60ms */
> +			rtc->reset_pin_assert_time = 60;
> +			device_property_read_u32(&pdev->dev,

It is probably more efficient to use of_property_read_u32 directly. Any
particular reason to use device_property_read_u32?

> +		} else {
> +			dev_err(&pdev->dev,
> +					"Poweroff handler already present!\n");

I'm not found of that alignement, it is probably better to let the
string go over 80 chars. checkpatch will not complain.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 4/5] rtc: jz4740_rtc: Add support for acting as the system power controller

[Alexandre Belloni]

On 05/03/2016 at 23:38:50 +0100, Paul Cercueil wrote :
> +	if (of_device_is_system_power_controller(pdev->dev.of_node)) {
> +		if (!pm_power_off) {
> +			/* Default: 60ms */
> +			rtc->reset_pin_assert_time = 60;
> +			device_property_read_u32(&pdev->dev,

It is probably more efficient to use of_property_read_u32 directly. Any
particular reason to use device_property_read_u32?

> +		} else {
> +			dev_err(&pdev->dev,
> +					"Poweroff handler already present!\n");

I'm not found of that alignement, it is probably better to let the
string go over 80 chars. checkpatch will not complain.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 4/5] rtc: jz4740_rtc: Add support for acting as the system power controller

[Alexandre Belloni]

On 05/03/2016 at 23:38:50 +0100, Paul Cercueil wrote :
> +	if (of_device_is_system_power_controller(pdev->dev.of_node)) {
> +		if (!pm_power_off) {
> +			/* Default: 60ms */
> +			rtc->reset_pin_assert_time = 60;
> +			device_property_read_u32(&pdev->dev,

It is probably more efficient to use of_property_read_u32 directly. Any
particular reason to use device_property_read_u32?

> +		} else {
> +			dev_err(&pdev->dev,
> +					"Poweroff handler already present!\n");

I'm not found of that alignement, it is probably better to let the
string go over 80 chars. checkpatch will not complain.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Alexandre Belloni]

Hi,

On 14/03/2016 at 02:53:53 +0100, Ralf Baechle wrote :
> On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:
> 
> > Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> > ---
> >  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
> >  arch/mips/jz4740/reset.c               | 64 ----------------------------------
> 
> Acked-by: Ralf Baechle <ralf@linux-mips.org>
> 
> Feel free to funnel this patch upstream through the RTC tree.  Or I can
> carry the whole series, just lemme know.
> 

I made a few minor comments. I'll take the series once it has been
resent.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Alexandre Belloni]

Hi,

On 14/03/2016 at 02:53:53 +0100, Ralf Baechle wrote :
> On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:
> 
> > Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> > ---
> >  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
> >  arch/mips/jz4740/reset.c               | 64 ----------------------------------
> 
> Acked-by: Ralf Baechle <ralf@linux-mips.org>
> 
> Feel free to funnel this patch upstream through the RTC tree.  Or I can
> carry the whole series, just lemme know.
> 

I made a few minor comments. I'll take the series once it has been
resent.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 5/5] MIPS: jz4740: Use the jz4740-rtc driver as the power controller

[Alexandre Belloni]

Hi,

On 14/03/2016 at 02:53:53 +0100, Ralf Baechle wrote :
> On Sat, Mar 05, 2016 at 11:38:51PM +0100, Paul Cercueil wrote:
> 
> > Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> > ---
> >  arch/mips/boot/dts/ingenic/jz4740.dtsi |  2 ++
> >  arch/mips/jz4740/reset.c               | 64 ----------------------------------
> 
> Acked-by: Ralf Baechle <ralf-6z/3iImG2C8G8FEW9MqTrA@public.gmane.org>
> 
> Feel free to funnel this patch upstream through the RTC tree.  Or I can
> carry the whole series, just lemme know.
> 

I made a few minor comments. I'll take the series once it has been
resent.

-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Harvey Hunt]

Hi Alexandre,

On 17/03/16 12:08, Alexandre Belloni wrote:
> On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>>   drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>>   1 file changed, 15 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
>> index 47617bd..3914b1c 100644
>> --- a/drivers/rtc/rtc-jz4740.c
>> +++ b/drivers/rtc/rtc-jz4740.c
>> @@ -17,6 +17,7 @@
>>   #include <linux/io.h>
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>> +#include <linux/of_device.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/rtc.h>
>>   #include <linux/slab.h>
>> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>>   }
>>   EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>>
>> +static const struct of_device_id jz4740_rtc_of_match[] = {
>> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
>> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
>
> ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> you have to add it there before using it.

Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7 
("devicetree/bindings: add Ingenic Semiconductor vendor prefix").

Thanks,

Harvey

[rtc-linux] Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Harvey Hunt]

Hi Alexandre,

On 17/03/16 12:08, Alexandre Belloni wrote:
> On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>>   drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>>   1 file changed, 15 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
>> index 47617bd..3914b1c 100644
>> --- a/drivers/rtc/rtc-jz4740.c
>> +++ b/drivers/rtc/rtc-jz4740.c
>> @@ -17,6 +17,7 @@
>>   #include <linux/io.h>
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>> +#include <linux/of_device.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/rtc.h>
>>   #include <linux/slab.h>
>> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>>   }
>>   EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>>
>> +static const struct of_device_id jz4740_rtc_of_match[] = {
>> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
>> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
>
> ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> you have to add it there before using it.

Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7 
("devicetree/bindings: add Ingenic Semiconductor vendor prefix").

Thanks,

Harvey

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Harvey Hunt]

Hi Alexandre,

On 17/03/16 12:08, Alexandre Belloni wrote:
> On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>>   drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
>>   1 file changed, 15 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
>> index 47617bd..3914b1c 100644
>> --- a/drivers/rtc/rtc-jz4740.c
>> +++ b/drivers/rtc/rtc-jz4740.c
>> @@ -17,6 +17,7 @@
>>   #include <linux/io.h>
>>   #include <linux/kernel.h>
>>   #include <linux/module.h>
>> +#include <linux/of_device.h>
>>   #include <linux/platform_device.h>
>>   #include <linux/rtc.h>
>>   #include <linux/slab.h>
>> @@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
>>   }
>>   EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
>>
>> +static const struct of_device_id jz4740_rtc_of_match[] = {
>> +	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
>> +	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
>
> ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> you have to add it there before using it.

Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7 
("devicetree/bindings: add Ingenic Semiconductor vendor prefix").

Thanks,

Harvey

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 17/03/2016 at 13:33:04 +0000, Harvey Hunt wrote :
> On 17/03/16 12:08, Alexandre Belloni wrote:
> >On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> >>Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> >>---
> >>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
> >>  1 file changed, 15 insertions(+), 1 deletion(-)
> >>
> >>diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> >>index 47617bd..3914b1c 100644
> >>--- a/drivers/rtc/rtc-jz4740.c
> >>+++ b/drivers/rtc/rtc-jz4740.c
> >>@@ -17,6 +17,7 @@
> >>  #include <linux/io.h>
> >>  #include <linux/kernel.h>
> >>  #include <linux/module.h>
> >>+#include <linux/of_device.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/rtc.h>
> >>  #include <linux/slab.h>
> >>@@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
> >>  }
> >>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
> >>
> >>+static const struct of_device_id jz4740_rtc_of_match[] = {
> >>+	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> >>+	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
> >
> >ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> >you have to add it there before using it.
> 
> Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7
> ("devicetree/bindings: add Ingenic Semiconductor vendor prefix").
> 

Indeed, I was looking at an old v4.1 based branch instead of master.

You can forget that comment :)


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 17/03/2016 at 13:33:04 +0000, Harvey Hunt wrote :
> On 17/03/16 12:08, Alexandre Belloni wrote:
> >On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> >>Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> >>---
> >>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
> >>  1 file changed, 15 insertions(+), 1 deletion(-)
> >>
> >>diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> >>index 47617bd..3914b1c 100644
> >>--- a/drivers/rtc/rtc-jz4740.c
> >>+++ b/drivers/rtc/rtc-jz4740.c
> >>@@ -17,6 +17,7 @@
> >>  #include <linux/io.h>
> >>  #include <linux/kernel.h>
> >>  #include <linux/module.h>
> >>+#include <linux/of_device.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/rtc.h>
> >>  #include <linux/slab.h>
> >>@@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
> >>  }
> >>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
> >>
> >>+static const struct of_device_id jz4740_rtc_of_match[] = {
> >>+	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> >>+	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
> >
> >ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> >you have to add it there before using it.
> 
> Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7
> ("devicetree/bindings: add Ingenic Semiconductor vendor prefix").
> 

Indeed, I was looking at an old v4.1 based branch instead of master.

You can forget that comment :)


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

-- 
-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH 3/5] rtc: rtc-jz4740: Add support for devicetree

[Alexandre Belloni]

On 17/03/2016 at 13:33:04 +0000, Harvey Hunt wrote :
> On 17/03/16 12:08, Alexandre Belloni wrote:
> >On 05/03/2016 at 23:38:49 +0100, Paul Cercueil wrote :
> >>Signed-off-by: Paul Cercueil <paul-icTtO2rgO2OTuSrc4Mpeew@public.gmane.org>
> >>---
> >>  drivers/rtc/rtc-jz4740.c | 16 +++++++++++++++-
> >>  1 file changed, 15 insertions(+), 1 deletion(-)
> >>
> >>diff --git a/drivers/rtc/rtc-jz4740.c b/drivers/rtc/rtc-jz4740.c
> >>index 47617bd..3914b1c 100644
> >>--- a/drivers/rtc/rtc-jz4740.c
> >>+++ b/drivers/rtc/rtc-jz4740.c
> >>@@ -17,6 +17,7 @@
> >>  #include <linux/io.h>
> >>  #include <linux/kernel.h>
> >>  #include <linux/module.h>
> >>+#include <linux/of_device.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/rtc.h>
> >>  #include <linux/slab.h>
> >>@@ -245,6 +246,13 @@ void jz4740_rtc_poweroff(struct device *dev)
> >>  }
> >>  EXPORT_SYMBOL_GPL(jz4740_rtc_poweroff);
> >>
> >>+static const struct of_device_id jz4740_rtc_of_match[] = {
> >>+	{ .compatible = "ingenic,jz4740-rtc", .data = (void *) ID_JZ4740 },
> >>+	{ .compatible = "ingenic,jz4780-rtc", .data = (void *) ID_JZ4780 },
> >
> >ingenic is not in Documentation/devicetree/bindings/vendor-prefixes.txt,
> >you have to add it there before using it.
> 
> Ingenic is in vendor-prefixes.txt - it was added by Commit f289cc7
> ("devicetree/bindings: add Ingenic Semiconductor vendor prefix").
> 

Indeed, I was looking at an old v4.1 based branch instead of master.

You can forget that comment :)


-- 
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html