From: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> To: Gary Bisson <gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org, robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, fabio.estevam-3arQi8VN3Tc@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org, mturquette-rdvid1DuHRBWk0Htik3J/w@public.gmane.org, troy.kisky-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org Subject: Re: [PATCH v3 4/9] ARM: dts: imx: add Boundary Devices Nitrogen7 board Date: Wed, 6 Apr 2016 22:15:57 +0800 [thread overview] Message-ID: <20160406141555.GL18833@tiger> (raw) In-Reply-To: <1459614351-16731-5-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> On Sat, Apr 02, 2016 at 06:25:46PM +0200, Gary Bisson wrote: > Based on i.MX7 Dual with 1GB of RAM. > > https://boundarydevices.com/product/nitrogen7/ > > Signed-off-by: Gary Bisson <gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> > --- > > Changes v1 -> v2: > - none > Changes v2 -> v3: > - Fix Nitrogen7 BT UART clock parent > - Fix Nitrogen7 lvdo2 node to be always-on > > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx7d-nitrogen7.dts | 819 ++++++++++++++++++++++++++++++++++ > 2 files changed, 820 insertions(+) > create mode 100644 arch/arm/boot/dts/imx7d-nitrogen7.dts <snip> > +/ { > + model = "Boundary Devices i.MX7 Nitrogen7 Board"; > + compatible = "boundary,imx7d-nitrogen7", "fsl,imx7d"; > + > + aliases { > + fb_lcd = &lcdif; > + t_lcd = &t_lcd; > + }; > + > + memory { > + reg = <0x80000000 0x40000000>; > + }; > + > + backlight_j9 { Use hyphen instead of underscore in node name. > + compatible = "gpio-backlight"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_backlight_j9>; > + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + default-on; > + }; > + > + backlight_j20 { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 5000000>; > + brightness-levels = <0 4 8 16 32 64 128 255>; > + default-brightness-level = <6>; > + status = "okay"; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; DT maintainers do not like this fake "simple-bus". Please put all these fixed regulators directly under root node in the naming schema below. reg_xxx: regulator-xxx { ... }; > + > + reg_usb_otg1_vbus: regulator@0 { > + compatible = "regulator-fixed"; > + reg = <0>; > + regulator-name = "usb_otg1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; <snip> > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; > + control-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; > + uart-has-rs485-half-duplex; > + rs485-mode = <1>; The above 3 properties are undefined? > + status = "okay"; > +}; > + > +&uart6 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart6>; > + assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>; > + fsl,uart-has-rtscts; > + status = "okay"; > +}; > + > +&usbotg1 { > + vbus-supply = <®_usb_otg1_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg1>; > + status = "okay"; > +}; > + > +&usbotg2 { > + vbus-supply = <®_usb_otg2_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg2>; > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; > + vmmc-supply = <&vgen3_reg>; > + bus-width = <4>; > + fsl,tuning-step = <2>; > + wakeup-source; > + keep-power-in-suspend; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + bus-width = <4>; > + non-removable; > + vmmc-supply = <®_wlan>; > + vqmmc-1-8-v; Unsupported property? > + cap-power-off-card; > + keep-power-in-suspend; > + status = "okay"; > + > + #address-cells = <1>; > + #size-cells = <0>; Move these two up to the top of property list. > + wlcore: wlcore@2 { > + compatible = "ti,wl1271"; > + reg = <2>; > + interrupt-parent = <&gpio4>; > + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; > + ref-clock-frequency = <38400000>; > + }; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3>; > + assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>; > + assigned-clock-rates = <400000000>; > + bus-width = <8>; > + fsl,tuning-step = <2>; > + non-removable; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog1>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog_1 &pinctrl_j2>; > + > + imx7d-nitrogen7 { Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function nodes), we can drop this container code to save one level of indentation. > + pinctrl_hog_1: hoggrp-1 { > + fsl,pins = < > + MX7D_PAD_SD3_RESET_B__GPIO6_IO11 0x5d > + MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x7d > + MX7D_PAD_ECSPI2_MISO__GPIO4_IO22 0x7d > + >; > + }; > + > + pinctrl_bt_rfkill: btrfkillgrp { > + fsl,pins = < > + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x7d > + >; > + }; Drop unused pinctrl entries, and let's add it when needed. > + > + pinctrl_enet1: enet1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3 > + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x3 > + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x3 > + MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x71 > + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 > + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 > + MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x71 > + MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x71 > + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 > + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x71 > + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x11 > + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x11 > + MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x11 > + MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x71 > + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x11 > + MX7D_PAD_SD3_STROBE__GPIO6_IO10 0x75 /* Reset */ > + >; > + }; > + > + pinctrl_flash: flashgrp { Ditto > + fsl,pins = < > + MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 0x71 > + MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 0x71 > + MX7D_PAD_EPDC_DATA02__GPIO2_IO2 0x7d > + MX7D_PAD_EPDC_DATA03__GPIO2_IO3 0x7d > + MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK 0x71 > + MX7D_PAD_EPDC_DATA06__GPIO2_IO6 0x71 > + >; > + }; <snip> > +&iomuxc_lpsr { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog_2>; > + > + imx7d-nitrogen7 { Drop this container node. Shawn > + pinctrl_hog_2: hoggrp-2 { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO02__GPIO1_IO2 0x7d > + MX7D_PAD_GPIO1_IO03__CCM_CLKO2 0x7d > + >; > + }; > + > + pinctrl_backlight_j9: backlightj9grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO07__GPIO1_IO7 0x7d > + >; > + }; > + > + pinctrl_pwm1: pwm1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO01__PWM1_OUT 0x7d > + >; > + }; > + > + pinctrl_usbotg1: usbotg1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO04__USB_OTG1_OC 0x7d > + MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x14 > + >; > + }; > + > + pinctrl_wdog1: wdog1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x75 > + >; > + }; > + }; > +}; > -- > 2.7.0 > > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: shawnguo@kernel.org (Shawn Guo) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v3 4/9] ARM: dts: imx: add Boundary Devices Nitrogen7 board Date: Wed, 6 Apr 2016 22:15:57 +0800 [thread overview] Message-ID: <20160406141555.GL18833@tiger> (raw) In-Reply-To: <1459614351-16731-5-git-send-email-gary.bisson@boundarydevices.com> On Sat, Apr 02, 2016 at 06:25:46PM +0200, Gary Bisson wrote: > Based on i.MX7 Dual with 1GB of RAM. > > https://boundarydevices.com/product/nitrogen7/ > > Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> > --- > > Changes v1 -> v2: > - none > Changes v2 -> v3: > - Fix Nitrogen7 BT UART clock parent > - Fix Nitrogen7 lvdo2 node to be always-on > > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx7d-nitrogen7.dts | 819 ++++++++++++++++++++++++++++++++++ > 2 files changed, 820 insertions(+) > create mode 100644 arch/arm/boot/dts/imx7d-nitrogen7.dts <snip> > +/ { > + model = "Boundary Devices i.MX7 Nitrogen7 Board"; > + compatible = "boundary,imx7d-nitrogen7", "fsl,imx7d"; > + > + aliases { > + fb_lcd = &lcdif; > + t_lcd = &t_lcd; > + }; > + > + memory { > + reg = <0x80000000 0x40000000>; > + }; > + > + backlight_j9 { Use hyphen instead of underscore in node name. > + compatible = "gpio-backlight"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_backlight_j9>; > + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + default-on; > + }; > + > + backlight_j20 { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 5000000>; > + brightness-levels = <0 4 8 16 32 64 128 255>; > + default-brightness-level = <6>; > + status = "okay"; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; DT maintainers do not like this fake "simple-bus". Please put all these fixed regulators directly under root node in the naming schema below. reg_xxx: regulator-xxx { ... }; > + > + reg_usb_otg1_vbus: regulator at 0 { > + compatible = "regulator-fixed"; > + reg = <0>; > + regulator-name = "usb_otg1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; <snip> > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; > + control-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; > + uart-has-rs485-half-duplex; > + rs485-mode = <1>; The above 3 properties are undefined? > + status = "okay"; > +}; > + > +&uart6 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart6>; > + assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>; > + fsl,uart-has-rtscts; > + status = "okay"; > +}; > + > +&usbotg1 { > + vbus-supply = <®_usb_otg1_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg1>; > + status = "okay"; > +}; > + > +&usbotg2 { > + vbus-supply = <®_usb_otg2_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg2>; > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; > + vmmc-supply = <&vgen3_reg>; > + bus-width = <4>; > + fsl,tuning-step = <2>; > + wakeup-source; > + keep-power-in-suspend; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + bus-width = <4>; > + non-removable; > + vmmc-supply = <®_wlan>; > + vqmmc-1-8-v; Unsupported property? > + cap-power-off-card; > + keep-power-in-suspend; > + status = "okay"; > + > + #address-cells = <1>; > + #size-cells = <0>; Move these two up to the top of property list. > + wlcore: wlcore at 2 { > + compatible = "ti,wl1271"; > + reg = <2>; > + interrupt-parent = <&gpio4>; > + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; > + ref-clock-frequency = <38400000>; > + }; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3>; > + assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>; > + assigned-clock-rates = <400000000>; > + bus-width = <8>; > + fsl,tuning-step = <2>; > + non-removable; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog1>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog_1 &pinctrl_j2>; > + > + imx7d-nitrogen7 { Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function nodes), we can drop this container code to save one level of indentation. > + pinctrl_hog_1: hoggrp-1 { > + fsl,pins = < > + MX7D_PAD_SD3_RESET_B__GPIO6_IO11 0x5d > + MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x7d > + MX7D_PAD_ECSPI2_MISO__GPIO4_IO22 0x7d > + >; > + }; > + > + pinctrl_bt_rfkill: btrfkillgrp { > + fsl,pins = < > + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x7d > + >; > + }; Drop unused pinctrl entries, and let's add it when needed. > + > + pinctrl_enet1: enet1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x3 > + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x3 > + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x3 > + MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC 0x71 > + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 > + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 > + MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 0x71 > + MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 0x71 > + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 > + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC 0x71 > + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x11 > + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x11 > + MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 0x11 > + MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 0x71 > + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x11 > + MX7D_PAD_SD3_STROBE__GPIO6_IO10 0x75 /* Reset */ > + >; > + }; > + > + pinctrl_flash: flashgrp { Ditto > + fsl,pins = < > + MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0 0x71 > + MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1 0x71 > + MX7D_PAD_EPDC_DATA02__GPIO2_IO2 0x7d > + MX7D_PAD_EPDC_DATA03__GPIO2_IO3 0x7d > + MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK 0x71 > + MX7D_PAD_EPDC_DATA06__GPIO2_IO6 0x71 > + >; > + }; <snip> > +&iomuxc_lpsr { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog_2>; > + > + imx7d-nitrogen7 { Drop this container node. Shawn > + pinctrl_hog_2: hoggrp-2 { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO02__GPIO1_IO2 0x7d > + MX7D_PAD_GPIO1_IO03__CCM_CLKO2 0x7d > + >; > + }; > + > + pinctrl_backlight_j9: backlightj9grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO07__GPIO1_IO7 0x7d > + >; > + }; > + > + pinctrl_pwm1: pwm1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO01__PWM1_OUT 0x7d > + >; > + }; > + > + pinctrl_usbotg1: usbotg1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO04__USB_OTG1_OC 0x7d > + MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x14 > + >; > + }; > + > + pinctrl_wdog1: wdog1grp { > + fsl,pins = < > + MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x75 > + >; > + }; > + }; > +}; > -- > 2.7.0 > >
next prev parent reply other threads:[~2016-04-06 14:15 UTC|newest] Thread overview: 94+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-03-15 10:30 [PATCH 0/9] imx: add latest Boundary Devices boards support Gary Bisson 2016-03-15 10:30 ` Gary Bisson [not found] ` <1458037826-19375-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-03-15 10:30 ` [PATCH 1/9] ARM: dts: imx7d: add lcdif support Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 2/9] ARM: dts: imx7d: add flexcan support Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 3/9] clk: imx: add ckil clock for i.MX7 Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 4/9] ARM: dts: imx: add Boundary Devices Nitrogen7 board Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 5/9] ARM: dts: imx: add Boundary Devices Nitrogen6_MAX QP board Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 6/9] ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board Gary Bisson 2016-03-15 10:30 ` Gary Bisson [not found] ` <1458037826-19375-7-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-03-15 10:53 ` Vladimir Zapolskiy 2016-03-15 10:53 ` Vladimir Zapolskiy [not found] ` <56E7E98F.5030902-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org> 2016-03-15 10:58 ` Gary Bisson 2016-03-15 10:58 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 7/9] ARM: imx_v6_v7_defconfig: add FT5x06 and TSC2004 touch support Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 8/9] ARM: imx_v6_v7_defconfig: add CONFIG_I2C_MUX_GPIO Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 10:30 ` [PATCH 9/9] ARM: imx_v6_v7_defconfig: add CONFIG_RTC_DRV_M41T80 Gary Bisson 2016-03-15 10:30 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 0/9] imx: add latest Boundary Devices boards support Gary Bisson 2016-03-15 14:04 ` Gary Bisson [not found] ` <1458050668-26748-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-03-15 14:04 ` [PATCH v2 1/9] ARM: dts: imx7d: add lcdif support Gary Bisson 2016-03-15 14:04 ` Gary Bisson [not found] ` <1458050668-26748-2-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-02 1:29 ` Shawn Guo 2016-04-02 1:29 ` Shawn Guo 2016-04-02 16:08 ` Gary Bisson 2016-04-02 16:08 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 2/9] ARM: dts: imx7d: add flexcan support Gary Bisson 2016-03-15 14:04 ` Gary Bisson [not found] ` <1458050668-26748-3-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-02 1:31 ` Shawn Guo 2016-04-02 1:31 ` Shawn Guo 2016-04-02 16:10 ` Gary Bisson 2016-04-02 16:10 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 3/9] clk: imx: add ckil clock for i.MX7 Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 4/9] ARM: dts: imx: add Boundary Devices Nitrogen7 board Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 5/9] ARM: dts: imx: add Boundary Devices Nitrogen6_MAX QP board Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 6/9] ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 7/9] ARM: imx_v6_v7_defconfig: add FT5x06 and TSC2004 touch support Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 8/9] ARM: imx_v6_v7_defconfig: add CONFIG_I2C_MUX_GPIO Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-03-15 14:04 ` [PATCH v2 9/9] ARM: imx_v6_v7_defconfig: add CONFIG_RTC_DRV_M41T80 Gary Bisson 2016-03-15 14:04 ` Gary Bisson 2016-04-02 16:25 ` [PATCH v3 0/9] imx: add latest Boundary Devices boards support Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-02 16:25 ` [PATCH v3 1/9] ARM: dts: imx7d: add lcdif support Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-2-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-06 9:06 ` Shawn Guo 2016-04-06 9:06 ` Shawn Guo 2016-04-02 16:25 ` [PATCH v3 2/9] ARM: dts: imx7d: add flexcan support Gary Bisson 2016-04-02 16:25 ` Gary Bisson 2016-04-02 16:25 ` [PATCH v3 3/9] clk: imx: add ckil clock for i.MX7 Gary Bisson 2016-04-02 16:25 ` Gary Bisson 2016-04-02 16:25 ` [PATCH v3 4/9] ARM: dts: imx: add Boundary Devices Nitrogen7 board Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-5-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-06 14:15 ` Shawn Guo [this message] 2016-04-06 14:15 ` Shawn Guo 2016-04-07 10:07 ` Gary Bisson 2016-04-07 10:07 ` Gary Bisson 2016-04-07 13:50 ` [PATCH v4] " Gary Bisson 2016-04-07 13:50 ` Gary Bisson [not found] ` <1460037057-23191-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-11 14:13 ` Shawn Guo 2016-04-11 14:13 ` Shawn Guo 2016-04-02 16:25 ` [PATCH v3 5/9] ARM: dts: imx: add Boundary Devices Nitrogen6_MAX QP board Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-6-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-06 14:25 ` Shawn Guo 2016-04-06 14:25 ` Shawn Guo 2016-04-02 16:25 ` [PATCH v3 6/9] ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-7-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-07 13:52 ` [PATCH v4] " Gary Bisson 2016-04-07 13:52 ` Gary Bisson [not found] ` <1460037168-23292-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-11 14:31 ` Shawn Guo 2016-04-11 14:31 ` Shawn Guo 2016-04-11 21:01 ` [PATCH v5] " Gary Bisson 2016-04-11 21:01 ` Gary Bisson [not found] ` <1460408496-21164-1-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-12 0:47 ` Shawn Guo 2016-04-12 0:47 ` Shawn Guo 2016-04-02 16:25 ` [PATCH v3 7/9] ARM: imx_v6_v7_defconfig: add FT5x06 and TSC2004 touch support Gary Bisson 2016-04-02 16:25 ` Gary Bisson [not found] ` <1459614351-16731-8-git-send-email-gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org> 2016-04-06 14:35 ` Shawn Guo 2016-04-06 14:35 ` Shawn Guo 2016-04-02 16:25 ` [PATCH v3 8/9] ARM: imx_v6_v7_defconfig: add CONFIG_I2C_MUX_GPIO Gary Bisson 2016-04-02 16:25 ` Gary Bisson 2016-04-02 16:25 ` [PATCH v3 9/9] ARM: imx_v6_v7_defconfig: add CONFIG_RTC_DRV_M41T80 Gary Bisson 2016-04-02 16:25 ` Gary Bisson
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20160406141555.GL18833@tiger \ --to=shawnguo-dgejt+ai2ygdnm+yrofe0a@public.gmane.org \ --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \ --cc=fabio.estevam-3arQi8VN3Tc@public.gmane.org \ --cc=gary.bisson-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org \ --cc=kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \ --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \ --cc=linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \ --cc=mturquette-rdvid1DuHRBWk0Htik3J/w@public.gmane.org \ --cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \ --cc=troy.kisky-Q5RJGjKts06CY9SHAMCTRUEOCMrvLtNR@public.gmane.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.