[PATCH V2 0/3] dmaengine: bcm2835: support dma channel 11 to 14

[PATCH V2 0/3] dmaengine: bcm2835: support dma channel 11 to 14

[kernel-TqfNSX0MhmxHKSADF0wUEw]

From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>

Right now the dma engine officially supports dma channel 11 and 12.
But the use of dma channel 12 immediately stalls the system.

The reason is that the interrupt assigned right now to dma channel 11
is actually a shared interrupt for dma channels 11 to 12.
So whenever the dma channel 12, 13 or 14 is used, it triggers the interrupt
for dma 11 which only clears the interrupt flag for dma channel 11.
This results in the interrupt 11 is triggered all the time.

On top the requesting dma channel12 (and the corresponding irq) triggers
an immeditate stall of the system, because for the 12th interrupt
any dma channel will trigger also this interrupt - even if the dma channel
is controlled by the firmware.

As the description in the default device-tree is (for the above reasons)
wrong a new means had to get devised that allows correct representation
of the mapping between interrupts and dma channels.

For this the existing (but unused) device-tree property "interrupt-names"
is used to define the mapping.

Implementing shared interrupts is another necessity when using dma channel
11 to 14, so it is a part of this patch.

This patchset requires: [PATCH 0/8 v4] bcm2835 DMA slave support
to be applied.

Tested playing BigBuckBunny on:
* fb-tft device (fb_st7735r)
  - via spi-bcm2835 using slave_sg dma
* I2S Hifiberry DAC (snd_soc_hifiberry_dac)
  - via bcm2835-i2s using cyclic dma
(with a few pending patches to make i2s work propperly)

Interrupt statistics after playing Big Buck Bunny:
root@raspcm:~# cat /proc/interrupts
           CPU0
 17:          0  ARMCTRL-level   1 Edge      2000b880.mailbox
 27:      47685  ARMCTRL-level  35 Edge      timer
 33:    6042130  ARMCTRL-level  41 Edge      20980000.usb, dwc2_hsotg:usb1
 40:      13250  ARMCTRL-level  48 Edge      DMA IRQ
 42:      13250  ARMCTRL-level  50 Edge      DMA IRQ
 44:      19087  ARMCTRL-level  52 Edge      DMA IRQ
 45:          0  ARMCTRL-level  53 Edge      DMA IRQ
 73:          0  ARMCTRL-level  81 Edge      20200000.gpio:bank0
 74:          0  ARMCTRL-level  82 Edge      20200000.gpio:bank1
 77:          0  ARMCTRL-level  85 Edge      20205000.i2c, 20804000.i2c, 20805000.i2c
 78:          0  ARMCTRL-level  86 Edge      20204000.spi
 81:        708  ARMCTRL-level  89 Edge      uart-pl011
 86:     277629  ARMCTRL-level  94 Edge      mmc0
Err:          0

Tested also with the following property set:
  brcm,dma-channel-mask = <0x7800>;
which results in only dma channels 11-14 being available
and thus all using the single shared irq.

Interrupt statistics for this case:
           CPU0
 17:          0  ARMCTRL-level   1 Edge      2000b880.mailbox
 27:      46843  ARMCTRL-level  35 Edge      timer
 33:    5412801  ARMCTRL-level  41 Edge      20980000.usb, dwc2_hsotg:usb1
 51:      45502  ARMCTRL-level  59 Edge      DMA IRQ, DMA IRQ, DMA IRQ, DMA IRQ
 73:          0  ARMCTRL-level  81 Edge      20200000.gpio:bank0
 74:          0  ARMCTRL-level  82 Edge      20200000.gpio:bank1
 77:          0  ARMCTRL-level  85 Edge      20205000.i2c, 20804000.i2c, 20805000.i2c
 78:          0  ARMCTRL-level  86 Edge      20204000.spi
 81:        706  ARMCTRL-level  89 Edge      uart-pl011
 86:     297235  ARMCTRL-level  94 Edge      mmc0
Err:          0

Note that support for more interrupts than irq 0 to 14
is not implemented (and this value is also hard-coded).

Allowing dma channel 15 to get controlled well would require
further extensive changes to the device-tree (separate register region).

Also as mentioned above dma-channel 15 is used by the firmware
and is - for all practical purposes - not available to
the kernel.

Only when this situation changes a valid effort can get made.

One major concern here is the fact that we have no dedicated interrupt
for dma channel 15. There is only the "catch all" interrupt, which - as
mentioned above - also triggers for dma channels used by the firmware,
which leads to an unnecessary amount of interrupts and can result
in system lockups...

The only potential usage would be for dma transfers where we do
not need an interrupt, but that may require further changes
to the dmaengine and more to support correctly.

One such "candidate" for the use of dma channel 15 could be
the tx-dma of spi-bcm2835, as for this specifically we only need
to get the interrupt when the rx-dma finishes, but that is a
very special case.

Avoiding the interrupt for the spi-tx-dma is still something that
could get investigated in a different patch-set.

Changelog:
  V1 -> V2: added explicit documentation for "dma-shared-all"
            to the dt-bindings documentation

Martin Sperl (3):
  dt/bindings: bcm2835: add interrupt-names property
  dmaengine: bcm2835: use platform_get_irq_byname
  ARM: bcm2835: add interrupt-names and apply correct mapping

 .../devicetree/bindings/dma/brcm,bcm2835-dma.txt   | 26 ++++++++
 arch/arm/boot/dts/bcm283x.dtsi                     | 22 ++++++-
 drivers/dma/bcm2835-dma.c                          | 77 ++++++++++++++++++----
 3 files changed, 110 insertions(+), 15 deletions(-)

--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 0/3] dmaengine: bcm2835: support dma channel 11 to 14

[kernel at martin.sperl.org]

From: Martin Sperl <kernel@martin.sperl.org>

Right now the dma engine officially supports dma channel 11 and 12.
But the use of dma channel 12 immediately stalls the system.

The reason is that the interrupt assigned right now to dma channel 11
is actually a shared interrupt for dma channels 11 to 12.
So whenever the dma channel 12, 13 or 14 is used, it triggers the interrupt
for dma 11 which only clears the interrupt flag for dma channel 11.
This results in the interrupt 11 is triggered all the time.

On top the requesting dma channel12 (and the corresponding irq) triggers
an immeditate stall of the system, because for the 12th interrupt
any dma channel will trigger also this interrupt - even if the dma channel
is controlled by the firmware.

As the description in the default device-tree is (for the above reasons)
wrong a new means had to get devised that allows correct representation
of the mapping between interrupts and dma channels.

For this the existing (but unused) device-tree property "interrupt-names"
is used to define the mapping.

Implementing shared interrupts is another necessity when using dma channel
11 to 14, so it is a part of this patch.

This patchset requires: [PATCH 0/8 v4] bcm2835 DMA slave support
to be applied.

Tested playing BigBuckBunny on:
* fb-tft device (fb_st7735r)
  - via spi-bcm2835 using slave_sg dma
* I2S Hifiberry DAC (snd_soc_hifiberry_dac)
  - via bcm2835-i2s using cyclic dma
(with a few pending patches to make i2s work propperly)

Interrupt statistics after playing Big Buck Bunny:
root at raspcm:~# cat /proc/interrupts
           CPU0
 17:          0  ARMCTRL-level   1 Edge      2000b880.mailbox
 27:      47685  ARMCTRL-level  35 Edge      timer
 33:    6042130  ARMCTRL-level  41 Edge      20980000.usb, dwc2_hsotg:usb1
 40:      13250  ARMCTRL-level  48 Edge      DMA IRQ
 42:      13250  ARMCTRL-level  50 Edge      DMA IRQ
 44:      19087  ARMCTRL-level  52 Edge      DMA IRQ
 45:          0  ARMCTRL-level  53 Edge      DMA IRQ
 73:          0  ARMCTRL-level  81 Edge      20200000.gpio:bank0
 74:          0  ARMCTRL-level  82 Edge      20200000.gpio:bank1
 77:          0  ARMCTRL-level  85 Edge      20205000.i2c, 20804000.i2c, 20805000.i2c
 78:          0  ARMCTRL-level  86 Edge      20204000.spi
 81:        708  ARMCTRL-level  89 Edge      uart-pl011
 86:     277629  ARMCTRL-level  94 Edge      mmc0
Err:          0

Tested also with the following property set:
  brcm,dma-channel-mask = <0x7800>;
which results in only dma channels 11-14 being available
and thus all using the single shared irq.

Interrupt statistics for this case:
           CPU0
 17:          0  ARMCTRL-level   1 Edge      2000b880.mailbox
 27:      46843  ARMCTRL-level  35 Edge      timer
 33:    5412801  ARMCTRL-level  41 Edge      20980000.usb, dwc2_hsotg:usb1
 51:      45502  ARMCTRL-level  59 Edge      DMA IRQ, DMA IRQ, DMA IRQ, DMA IRQ
 73:          0  ARMCTRL-level  81 Edge      20200000.gpio:bank0
 74:          0  ARMCTRL-level  82 Edge      20200000.gpio:bank1
 77:          0  ARMCTRL-level  85 Edge      20205000.i2c, 20804000.i2c, 20805000.i2c
 78:          0  ARMCTRL-level  86 Edge      20204000.spi
 81:        706  ARMCTRL-level  89 Edge      uart-pl011
 86:     297235  ARMCTRL-level  94 Edge      mmc0
Err:          0

Note that support for more interrupts than irq 0 to 14
is not implemented (and this value is also hard-coded).

Allowing dma channel 15 to get controlled well would require
further extensive changes to the device-tree (separate register region).

Also as mentioned above dma-channel 15 is used by the firmware
and is - for all practical purposes - not available to
the kernel.

Only when this situation changes a valid effort can get made.

One major concern here is the fact that we have no dedicated interrupt
for dma channel 15. There is only the "catch all" interrupt, which - as
mentioned above - also triggers for dma channels used by the firmware,
which leads to an unnecessary amount of interrupts and can result
in system lockups...

The only potential usage would be for dma transfers where we do
not need an interrupt, but that may require further changes
to the dmaengine and more to support correctly.

One such "candidate" for the use of dma channel 15 could be
the tx-dma of spi-bcm2835, as for this specifically we only need
to get the interrupt when the rx-dma finishes, but that is a
very special case.

Avoiding the interrupt for the spi-tx-dma is still something that
could get investigated in a different patch-set.

Changelog:
  V1 -> V2: added explicit documentation for "dma-shared-all"
            to the dt-bindings documentation

Martin Sperl (3):
  dt/bindings: bcm2835: add interrupt-names property
  dmaengine: bcm2835: use platform_get_irq_byname
  ARM: bcm2835: add interrupt-names and apply correct mapping

 .../devicetree/bindings/dma/brcm,bcm2835-dma.txt   | 26 ++++++++
 arch/arm/boot/dts/bcm283x.dtsi                     | 22 ++++++-
 drivers/dma/bcm2835-dma.c                          | 77 ++++++++++++++++++----
 3 files changed, 110 insertions(+), 15 deletions(-)

--
2.1.4

[PATCH V2 1/3] dt/bindings: bcm2835: add interrupt-names property

[kernel-TqfNSX0MhmxHKSADF0wUEw]

From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>

Added standard interrupt-names property so that
platform_get_irq_byname() can get used to fetch the
interrupt corresponding to each dma_channel
instead of the current platform_get_irq() with
an assumed ordering of the interrupts.

Signed-off-by: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Acked-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
Acked-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
---
 .../devicetree/bindings/dma/brcm,bcm2835-dma.txt   | 26 ++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
index 1396078..baf9b34 100644
--- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
+++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
@@ -12,6 +12,10 @@ Required properties:
 - reg: Should contain DMA registers location and length.
 - interrupts: Should contain the DMA interrupts associated
 		to the DMA channels in ascending order.
+- interrupt-names: Should contain the names of the interrupt
+		   in the form "dmaXX".
+		   Use "dma-shared-all" for the common interrupt line
+		   that is shared by all dma channels.
 - #dma-cells: Must be <1>, the cell in the dmas property of the
 		client device represents the DREQ number.
 - brcm,dma-channel-mask: Bit mask representing the channels
@@ -34,13 +38,35 @@ dma: dma@7e007000 {
 		     <1 24>,
 		     <1 25>,
 		     <1 26>,
+		     /* dma channel 11-14 share one irq */
 		     <1 27>,
+		     <1 27>,
+		     <1 27>,
+		     <1 27>,
+		     /* unused shared irq for all channels */
 		     <1 28>;
+	interrupt-names = "dma0",
+			  "dma1",
+			  "dma2",
+			  "dma3",
+			  "dma4",
+			  "dma5",
+			  "dma6",
+			  "dma7",
+			  "dma8",
+			  "dma9",
+			  "dma10",
+			  "dma11",
+			  "dma12",
+			  "dma13",
+			  "dma14",
+			  "dma-shared-all";
 
 	#dma-cells = <1>;
 	brcm,dma-channel-mask = <0x7f35>;
 };
 
+
 DMA clients connected to the BCM2835 DMA controller must use the format
 described in the dma.txt file, using a two-cell specifier for each channel.
 
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 1/3] dt/bindings: bcm2835: add interrupt-names property

[kernel at martin.sperl.org]

From: Martin Sperl <kernel@martin.sperl.org>

Added standard interrupt-names property so that
platform_get_irq_byname() can get used to fetch the
interrupt corresponding to each dma_channel
instead of the current platform_get_irq() with
an assumed ordering of the interrupts.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
---
 .../devicetree/bindings/dma/brcm,bcm2835-dma.txt   | 26 ++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
index 1396078..baf9b34 100644
--- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
+++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
@@ -12,6 +12,10 @@ Required properties:
 - reg: Should contain DMA registers location and length.
 - interrupts: Should contain the DMA interrupts associated
 		to the DMA channels in ascending order.
+- interrupt-names: Should contain the names of the interrupt
+		   in the form "dmaXX".
+		   Use "dma-shared-all" for the common interrupt line
+		   that is shared by all dma channels.
 - #dma-cells: Must be <1>, the cell in the dmas property of the
 		client device represents the DREQ number.
 - brcm,dma-channel-mask: Bit mask representing the channels
@@ -34,13 +38,35 @@ dma: dma at 7e007000 {
 		     <1 24>,
 		     <1 25>,
 		     <1 26>,
+		     /* dma channel 11-14 share one irq */
 		     <1 27>,
+		     <1 27>,
+		     <1 27>,
+		     <1 27>,
+		     /* unused shared irq for all channels */
 		     <1 28>;
+	interrupt-names = "dma0",
+			  "dma1",
+			  "dma2",
+			  "dma3",
+			  "dma4",
+			  "dma5",
+			  "dma6",
+			  "dma7",
+			  "dma8",
+			  "dma9",
+			  "dma10",
+			  "dma11",
+			  "dma12",
+			  "dma13",
+			  "dma14",
+			  "dma-shared-all";
 
 	#dma-cells = <1>;
 	brcm,dma-channel-mask = <0x7f35>;
 };
 
+
 DMA clients connected to the BCM2835 DMA controller must use the format
 described in the dma.txt file, using a two-cell specifier for each channel.
 
-- 
2.1.4

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[kernel-TqfNSX0MhmxHKSADF0wUEw]

From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>

Use platform_get_irq_byname to allow for correct mapping of
interrupts to dma channels.

The currently implemented device tree is unfortunately
implemented with the wrong assumption, that each dma-channel
has its own dma channel, but dma-irq 11 is handling
dma-channel 11-14 and dma-irq 12 is actually a "catch all"
interrupt.

So here we use the byname variant and require that interrupts
are explicitly named via the interrupts-name property in the
device tree.

The use of shared interrupts is also implemented.

As a side-effect this means we can now use dma channels 12, 13 and 14
in a correct manner - also testing shows that onl using
channels 11 to 14 for spi and i2s works perfectly (when playing
some video)

Signed-off-by: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
Acked-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
Acked-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
---
 drivers/dma/bcm2835-dma.c | 77 ++++++++++++++++++++++++++++++++++++++---------
 1 file changed, 63 insertions(+), 14 deletions(-)

diff --git a/drivers/dma/bcm2835-dma.c b/drivers/dma/bcm2835-dma.c
index cc771cd..9740151 100644
--- a/drivers/dma/bcm2835-dma.c
+++ b/drivers/dma/bcm2835-dma.c
@@ -46,6 +46,9 @@
 
 #include "virt-dma.h"
 
+#define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14
+#define BCM2835_DMA_CHAN_NAME_SIZE 8
+
 struct bcm2835_dmadev {
 	struct dma_device ddev;
 	spinlock_t lock;
@@ -81,6 +84,7 @@ struct bcm2835_chan {
 
 	void __iomem *chan_base;
 	int irq_number;
+	unsigned int irq_flags;
 
 	bool is_lite_channel;
 };
@@ -466,6 +470,15 @@ static irqreturn_t bcm2835_dma_callback(int irq, void *data)
 	struct bcm2835_desc *d;
 	unsigned long flags;
 
+	/* check the shared interrupt */
+	if (c->irq_flags & IRQF_SHARED) {
+		/* check if the interrupt is enabled */
+		flags = readl(c->chan_base + BCM2835_DMA_CS);
+		/* if not set then we are not the reason for the irq */
+		if (!(flags & BCM2835_DMA_INT))
+			return IRQ_NONE;
+	}
+
 	spin_lock_irqsave(&c->vc.lock, flags);
 
 	/* Acknowledge interrupt */
@@ -506,8 +519,8 @@ static int bcm2835_dma_alloc_chan_resources(struct dma_chan *chan)
 		return -ENOMEM;
 	}
 
-	return request_irq(c->irq_number,
-			bcm2835_dma_callback, 0, "DMA IRQ", c);
+	return request_irq(c->irq_number, bcm2835_dma_callback,
+			   c->irq_flags, "DMA IRQ", c);
 }
 
 static void bcm2835_dma_free_chan_resources(struct dma_chan *chan)
@@ -819,7 +832,8 @@ static int bcm2835_dma_terminate_all(struct dma_chan *chan)
 	return 0;
 }
 
-static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq)
+static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id,
+				 int irq, unsigned int irq_flags)
 {
 	struct bcm2835_chan *c;
 
@@ -834,6 +848,7 @@ static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq)
 	c->chan_base = BCM2835_DMA_CHANIO(d->base, chan_id);
 	c->ch = chan_id;
 	c->irq_number = irq;
+	c->irq_flags = irq_flags;
 
 	/* check in DEBUG register if this is a LITE channel */
 	if (readl(c->chan_base + BCM2835_DMA_DEBUG) &
@@ -882,9 +897,11 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int rc;
-	int i;
-	int irq;
+	int i, j;
+	int irq[BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED + 1];
+	int irq_flags;
 	uint32_t chans_available;
+	char chan_name[BCM2835_DMA_CHAN_NAME_SIZE];
 
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
@@ -941,16 +958,48 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 		goto err_no_dma;
 	}
 
-	for (i = 0; i < pdev->num_resources; i++) {
-		irq = platform_get_irq(pdev, i);
-		if (irq < 0)
-			break;
-
-		if (chans_available & (1 << i)) {
-			rc = bcm2835_dma_chan_init(od, i, irq);
-			if (rc)
-				goto err_no_dma;
+	/* get irqs for each channel that we support */
+	for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
+		/* skip masked out channels */
+		if (!(chans_available & (1 << i))) {
+			irq[i] = -1;
+			continue;
 		}
+
+		/* get the named irq */
+		snprintf(chan_name, sizeof(chan_name), "dma%i", i);
+		irq[i] = platform_get_irq_byname(pdev, chan_name);
+		if (irq[i] >= 0)
+			continue;
+
+		/* legacy device tree case handling */
+		dev_warn_once(&pdev->dev,
+			      "missing interrupts-names property in device tree - legacy interpretation is used");
+		/*
+		 * in case of channel >= 11
+		 * use the 11th interrupt and that is shared
+		 */
+		irq[i] = platform_get_irq(pdev, i < 11 ? i : 11);
+	}
+
+	/* get irqs for each channel */
+	for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
+		/* skip channels without irq */
+		if (irq[i] < 0)
+			continue;
+
+		/* check if there are other channels that also use this irq */
+		irq_flags = 0;
+		for (j = 0; j <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; j++)
+			if ((i != j) && (irq[j] == irq[i])) {
+				irq_flags = IRQF_SHARED;
+				break;
+			}
+
+		/* initialize the channel */
+		rc = bcm2835_dma_chan_init(od, i, irq[i], irq_flags);
+		if (rc)
+			goto err_no_dma;
 	}
 
 	dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", i);
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[kernel at martin.sperl.org]

From: Martin Sperl <kernel@martin.sperl.org>

Use platform_get_irq_byname to allow for correct mapping of
interrupts to dma channels.

The currently implemented device tree is unfortunately
implemented with the wrong assumption, that each dma-channel
has its own dma channel, but dma-irq 11 is handling
dma-channel 11-14 and dma-irq 12 is actually a "catch all"
interrupt.

So here we use the byname variant and require that interrupts
are explicitly named via the interrupts-name property in the
device tree.

The use of shared interrupts is also implemented.

As a side-effect this means we can now use dma channels 12, 13 and 14
in a correct manner - also testing shows that onl using
channels 11 to 14 for spi and i2s works perfectly (when playing
some video)

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
---
 drivers/dma/bcm2835-dma.c | 77 ++++++++++++++++++++++++++++++++++++++---------
 1 file changed, 63 insertions(+), 14 deletions(-)

diff --git a/drivers/dma/bcm2835-dma.c b/drivers/dma/bcm2835-dma.c
index cc771cd..9740151 100644
--- a/drivers/dma/bcm2835-dma.c
+++ b/drivers/dma/bcm2835-dma.c
@@ -46,6 +46,9 @@
 
 #include "virt-dma.h"
 
+#define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14
+#define BCM2835_DMA_CHAN_NAME_SIZE 8
+
 struct bcm2835_dmadev {
 	struct dma_device ddev;
 	spinlock_t lock;
@@ -81,6 +84,7 @@ struct bcm2835_chan {
 
 	void __iomem *chan_base;
 	int irq_number;
+	unsigned int irq_flags;
 
 	bool is_lite_channel;
 };
@@ -466,6 +470,15 @@ static irqreturn_t bcm2835_dma_callback(int irq, void *data)
 	struct bcm2835_desc *d;
 	unsigned long flags;
 
+	/* check the shared interrupt */
+	if (c->irq_flags & IRQF_SHARED) {
+		/* check if the interrupt is enabled */
+		flags = readl(c->chan_base + BCM2835_DMA_CS);
+		/* if not set then we are not the reason for the irq */
+		if (!(flags & BCM2835_DMA_INT))
+			return IRQ_NONE;
+	}
+
 	spin_lock_irqsave(&c->vc.lock, flags);
 
 	/* Acknowledge interrupt */
@@ -506,8 +519,8 @@ static int bcm2835_dma_alloc_chan_resources(struct dma_chan *chan)
 		return -ENOMEM;
 	}
 
-	return request_irq(c->irq_number,
-			bcm2835_dma_callback, 0, "DMA IRQ", c);
+	return request_irq(c->irq_number, bcm2835_dma_callback,
+			   c->irq_flags, "DMA IRQ", c);
 }
 
 static void bcm2835_dma_free_chan_resources(struct dma_chan *chan)
@@ -819,7 +832,8 @@ static int bcm2835_dma_terminate_all(struct dma_chan *chan)
 	return 0;
 }
 
-static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq)
+static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id,
+				 int irq, unsigned int irq_flags)
 {
 	struct bcm2835_chan *c;
 
@@ -834,6 +848,7 @@ static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq)
 	c->chan_base = BCM2835_DMA_CHANIO(d->base, chan_id);
 	c->ch = chan_id;
 	c->irq_number = irq;
+	c->irq_flags = irq_flags;
 
 	/* check in DEBUG register if this is a LITE channel */
 	if (readl(c->chan_base + BCM2835_DMA_DEBUG) &
@@ -882,9 +897,11 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int rc;
-	int i;
-	int irq;
+	int i, j;
+	int irq[BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED + 1];
+	int irq_flags;
 	uint32_t chans_available;
+	char chan_name[BCM2835_DMA_CHAN_NAME_SIZE];
 
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
@@ -941,16 +958,48 @@ static int bcm2835_dma_probe(struct platform_device *pdev)
 		goto err_no_dma;
 	}
 
-	for (i = 0; i < pdev->num_resources; i++) {
-		irq = platform_get_irq(pdev, i);
-		if (irq < 0)
-			break;
-
-		if (chans_available & (1 << i)) {
-			rc = bcm2835_dma_chan_init(od, i, irq);
-			if (rc)
-				goto err_no_dma;
+	/* get irqs for each channel that we support */
+	for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
+		/* skip masked out channels */
+		if (!(chans_available & (1 << i))) {
+			irq[i] = -1;
+			continue;
 		}
+
+		/* get the named irq */
+		snprintf(chan_name, sizeof(chan_name), "dma%i", i);
+		irq[i] = platform_get_irq_byname(pdev, chan_name);
+		if (irq[i] >= 0)
+			continue;
+
+		/* legacy device tree case handling */
+		dev_warn_once(&pdev->dev,
+			      "missing interrupts-names property in device tree - legacy interpretation is used");
+		/*
+		 * in case of channel >= 11
+		 * use the 11th interrupt and that is shared
+		 */
+		irq[i] = platform_get_irq(pdev, i < 11 ? i : 11);
+	}
+
+	/* get irqs for each channel */
+	for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
+		/* skip channels without irq */
+		if (irq[i] < 0)
+			continue;
+
+		/* check if there are other channels that also use this irq */
+		irq_flags = 0;
+		for (j = 0; j <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; j++)
+			if ((i != j) && (irq[j] == irq[i])) {
+				irq_flags = IRQF_SHARED;
+				break;
+			}
+
+		/* initialize the channel */
+		rc = bcm2835_dma_chan_init(od, i, irq[i], irq_flags);
+		if (rc)
+			goto err_no_dma;
 	}
 
 	dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", i);
-- 
2.1.4

[PATCH V2 3/3] ARM: bcm2835: add interrupt-names and apply correct mapping

[kernel-TqfNSX0MhmxHKSADF0wUEw]

From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>

Add interrupt-names properties to dt and apply the correct
mapping between irq and dma channels.

Signed-off-by: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
Acked-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
Acked-by: Eric Anholt <eric-WhKQ6XTQaPysTnJN9+BGXg@public.gmane.org>
---
 arch/arm/boot/dts/bcm283x.dtsi | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 8aaf193..84dcf3e 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -47,9 +47,29 @@
 				     <1 24>,
 				     <1 25>,
 				     <1 26>,
+				     /* dma channel 11-14 share one irq */
 				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
 				     <1 28>;
-
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
 			#dma-cells = <1>;
 			brcm,dma-channel-mask = <0x7f35>;
 		};
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 3/3] ARM: bcm2835: add interrupt-names and apply correct mapping

[kernel at martin.sperl.org]

From: Martin Sperl <kernel@martin.sperl.org>

Add interrupt-names properties to dt and apply the correct
mapping between irq and dma channels.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 8aaf193..84dcf3e 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -47,9 +47,29 @@
 				     <1 24>,
 				     <1 25>,
 				     <1 26>,
+				     /* dma channel 11-14 share one irq */
 				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     <1 27>,
+				     /* unused shared irq for all channels */
 				     <1 28>;
-
+			interrupt-names = "dma0",
+					  "dma1",
+					  "dma2",
+					  "dma3",
+					  "dma4",
+					  "dma5",
+					  "dma6",
+					  "dma7",
+					  "dma8",
+					  "dma9",
+					  "dma10",
+					  "dma11",
+					  "dma12",
+					  "dma13",
+					  "dma14",
+					  "dma-shared-all";
 			#dma-cells = <1>;
 			brcm,dma-channel-mask = <0x7f35>;
 		};
-- 
2.1.4

Re: [PATCH V2 0/3] dmaengine: bcm2835: support dma channel 11 to 14

[Vinod Koul]

On Mon, Apr 11, 2016 at 01:29:06PM +0000, kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org wrote:
> From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
> 
> Right now the dma engine officially supports dma channel 11 and 12.
> But the use of dma channel 12 immediately stalls the system.
> 
> The reason is that the interrupt assigned right now to dma channel 11
> is actually a shared interrupt for dma channels 11 to 12.
> So whenever the dma channel 12, 13 or 14 is used, it triggers the interrupt
> for dma 11 which only clears the interrupt flag for dma channel 11.
> This results in the interrupt 11 is triggered all the time.
> 
> On top the requesting dma channel12 (and the corresponding irq) triggers
> an immeditate stall of the system, because for the 12th interrupt
> any dma channel will trigger also this interrupt - even if the dma channel
> is controlled by the firmware.
> 
> As the description in the default device-tree is (for the above reasons)
> wrong a new means had to get devised that allows correct representation
> of the mapping between interrupts and dma channels.
> 
> For this the existing (but unused) device-tree property "interrupt-names"
> is used to define the mapping.
> 
> Implementing shared interrupts is another necessity when using dma channel
> 11 to 14, so it is a part of this patch.

Applied, thanks

-- 
~Vinod
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 0/3] dmaengine: bcm2835: support dma channel 11 to 14

[Vinod Koul]

On Mon, Apr 11, 2016 at 01:29:06PM +0000, kernel at martin.sperl.org wrote:
> From: Martin Sperl <kernel@martin.sperl.org>
> 
> Right now the dma engine officially supports dma channel 11 and 12.
> But the use of dma channel 12 immediately stalls the system.
> 
> The reason is that the interrupt assigned right now to dma channel 11
> is actually a shared interrupt for dma channels 11 to 12.
> So whenever the dma channel 12, 13 or 14 is used, it triggers the interrupt
> for dma 11 which only clears the interrupt flag for dma channel 11.
> This results in the interrupt 11 is triggered all the time.
> 
> On top the requesting dma channel12 (and the corresponding irq) triggers
> an immeditate stall of the system, because for the 12th interrupt
> any dma channel will trigger also this interrupt - even if the dma channel
> is controlled by the firmware.
> 
> As the description in the default device-tree is (for the above reasons)
> wrong a new means had to get devised that allows correct representation
> of the mapping between interrupts and dma channels.
> 
> For this the existing (but unused) device-tree property "interrupt-names"
> is used to define the mapping.
> 
> Implementing shared interrupts is another necessity when using dma channel
> 11 to 14, so it is a part of this patch.

Applied, thanks

-- 
~Vinod

Re: [PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Geert Uytterhoeven]

On Mon, Apr 11, 2016 at 3:29 PM,  <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
> From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
>
> Use platform_get_irq_byname to allow for correct mapping of
> interrupts to dma channels.
>
> The currently implemented device tree is unfortunately
> implemented with the wrong assumption, that each dma-channel
> has its own dma channel, but dma-irq 11 is handling
> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
> interrupt.
>
> So here we use the byname variant and require that interrupts
> are explicitly named via the interrupts-name property in the

interrupt-names

> device tree.
>
> The use of shared interrupts is also implemented.

You're not explicitly looking for "dma-shared-all" for that?
You might as well just declare a single unnamed interrupt in the bindings.

> +               /* legacy device tree case handling */
> +               dev_warn_once(&pdev->dev,
> +                             "missing interrupts-names property in device tree - legacy interpretation is used");

interrupt-names

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Geert Uytterhoeven]

On Mon, Apr 11, 2016 at 3:29 PM,  <kernel@martin.sperl.org> wrote:
> From: Martin Sperl <kernel@martin.sperl.org>
>
> Use platform_get_irq_byname to allow for correct mapping of
> interrupts to dma channels.
>
> The currently implemented device tree is unfortunately
> implemented with the wrong assumption, that each dma-channel
> has its own dma channel, but dma-irq 11 is handling
> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
> interrupt.
>
> So here we use the byname variant and require that interrupts
> are explicitly named via the interrupts-name property in the

interrupt-names

> device tree.
>
> The use of shared interrupts is also implemented.

You're not explicitly looking for "dma-shared-all" for that?
You might as well just declare a single unnamed interrupt in the bindings.

> +               /* legacy device tree case handling */
> +               dev_warn_once(&pdev->dev,
> +                             "missing interrupts-names property in device tree - legacy interpretation is used");

interrupt-names

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Martin Sperl]

On 20.04.2016 08:51, Geert Uytterhoeven wrote:
> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
>> From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
>>
>> Use platform_get_irq_byname to allow for correct mapping of
>> interrupts to dma channels.
>>
>> The currently implemented device tree is unfortunately
>> implemented with the wrong assumption, that each dma-channel
>> has its own dma channel, but dma-irq 11 is handling
>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
>> interrupt.
>>
>> So here we use the byname variant and require that interrupts
>> are explicitly named via the interrupts-name property in the
>
> interrupt-names


Vinod has just merged this patch - do you want me to submit another
to correct those?

> You're not explicitly looking for "dma-shared-all" for that?
> You might as well just declare a single unnamed interrupt in the bindings.

dma-shared-all is unfortunately an interrupt-line that triggers
for interrupt-channels 0-15 and that includes the dma channels
that are owned by the firmware.

It is there mostly to document the interrupt-line (which is there in the 
existing device tree files - it is not used.

Martin
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Martin Sperl]

On 20.04.2016 08:51, Geert Uytterhoeven wrote:
> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel@martin.sperl.org> wrote:
>> From: Martin Sperl <kernel@martin.sperl.org>
>>
>> Use platform_get_irq_byname to allow for correct mapping of
>> interrupts to dma channels.
>>
>> The currently implemented device tree is unfortunately
>> implemented with the wrong assumption, that each dma-channel
>> has its own dma channel, but dma-irq 11 is handling
>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
>> interrupt.
>>
>> So here we use the byname variant and require that interrupts
>> are explicitly named via the interrupts-name property in the
>
> interrupt-names


Vinod has just merged this patch - do you want me to submit another
to correct those?

> You're not explicitly looking for "dma-shared-all" for that?
> You might as well just declare a single unnamed interrupt in the bindings.

dma-shared-all is unfortunately an interrupt-line that triggers
for interrupt-channels 0-15 and that includes the dma channels
that are owned by the firmware.

It is there mostly to document the interrupt-line (which is there in the 
existing device tree files - it is not used.

Martin

Re: [PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Geert Uytterhoeven]

Hi Martin,

On Wed, Apr 20, 2016 at 1:06 PM, Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
> On 20.04.2016 08:51, Geert Uytterhoeven wrote:
>>
>> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
>>>
>>> From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
>>>
>>> Use platform_get_irq_byname to allow for correct mapping of
>>> interrupts to dma channels.
>>>
>>> The currently implemented device tree is unfortunately
>>> implemented with the wrong assumption, that each dma-channel
>>> has its own dma channel, but dma-irq 11 is handling
>>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
>>> interrupt.
>>>
>>> So here we use the byname variant and require that interrupts
>>> are explicitly named via the interrupts-name property in the
>>
>> interrupt-names
>
> Vinod has just merged this patch - do you want me to submit another

Yeah, that's how I noticed by accident :-)

> to correct those?

For the commit message it's indeed too late. For the error message in the
code, yes please.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Geert Uytterhoeven]

Hi Martin,

On Wed, Apr 20, 2016 at 1:06 PM, Martin Sperl <kernel@martin.sperl.org> wrote:
> On 20.04.2016 08:51, Geert Uytterhoeven wrote:
>>
>> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel@martin.sperl.org> wrote:
>>>
>>> From: Martin Sperl <kernel@martin.sperl.org>
>>>
>>> Use platform_get_irq_byname to allow for correct mapping of
>>> interrupts to dma channels.
>>>
>>> The currently implemented device tree is unfortunately
>>> implemented with the wrong assumption, that each dma-channel
>>> has its own dma channel, but dma-irq 11 is handling
>>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
>>> interrupt.
>>>
>>> So here we use the byname variant and require that interrupts
>>> are explicitly named via the interrupts-name property in the
>>
>> interrupt-names
>
> Vinod has just merged this patch - do you want me to submit another

Yeah, that's how I noticed by accident :-)

> to correct those?

For the commit message it's indeed too late. For the error message in the
code, yes please.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Vinod Koul]

On Wed, Apr 20, 2016 at 01:12:36PM +0200, Geert Uytterhoeven wrote:
> Hi Martin,
> 
> On Wed, Apr 20, 2016 at 1:06 PM, Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
> > On 20.04.2016 08:51, Geert Uytterhoeven wrote:
> >>
> >> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org> wrote:
> >>>
> >>> From: Martin Sperl <kernel-TqfNSX0MhmxHKSADF0wUEw@public.gmane.org>
> >>>
> >>> Use platform_get_irq_byname to allow for correct mapping of
> >>> interrupts to dma channels.
> >>>
> >>> The currently implemented device tree is unfortunately
> >>> implemented with the wrong assumption, that each dma-channel
> >>> has its own dma channel, but dma-irq 11 is handling
> >>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
> >>> interrupt.
> >>>
> >>> So here we use the byname variant and require that interrupts
> >>> are explicitly named via the interrupts-name property in the
> >>
> >> interrupt-names

well spotted

> >
> > Vinod has just merged this patch - do you want me to submit another
> 
> Yeah, that's how I noticed by accident :-)
> 
> > to correct those?
> 
> For the commit message it's indeed too late. For the error message in the
> code, yes please.

I can drop the branch

-- 
~Vinod
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 2/3] dmaengine: bcm2835: use platform_get_irq_byname

[Vinod Koul]

On Wed, Apr 20, 2016 at 01:12:36PM +0200, Geert Uytterhoeven wrote:
> Hi Martin,
> 
> On Wed, Apr 20, 2016 at 1:06 PM, Martin Sperl <kernel@martin.sperl.org> wrote:
> > On 20.04.2016 08:51, Geert Uytterhoeven wrote:
> >>
> >> On Mon, Apr 11, 2016 at 3:29 PM,  <kernel@martin.sperl.org> wrote:
> >>>
> >>> From: Martin Sperl <kernel@martin.sperl.org>
> >>>
> >>> Use platform_get_irq_byname to allow for correct mapping of
> >>> interrupts to dma channels.
> >>>
> >>> The currently implemented device tree is unfortunately
> >>> implemented with the wrong assumption, that each dma-channel
> >>> has its own dma channel, but dma-irq 11 is handling
> >>> dma-channel 11-14 and dma-irq 12 is actually a "catch all"
> >>> interrupt.
> >>>
> >>> So here we use the byname variant and require that interrupts
> >>> are explicitly named via the interrupts-name property in the
> >>
> >> interrupt-names

well spotted

> >
> > Vinod has just merged this patch - do you want me to submit another
> 
> Yeah, that's how I noticed by accident :-)
> 
> > to correct those?
> 
> For the commit message it's indeed too late. For the error message in the
> code, yes please.

I can drop the branch

-- 
~Vinod