* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
@ 2016-04-19 19:45 Uwe Kleine-König
2016-04-19 21:19 ` Russell King - ARM Linux
0 siblings, 1 reply; 12+ messages in thread
From: Uwe Kleine-König @ 2016-04-19 19:45 UTC (permalink / raw)
To: linux-arm-kernel
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
---
arch/arm/boot/dts/imx25-pinfunc.h | 620 +++++++++++++++++++-------------------
1 file changed, 310 insertions(+), 310 deletions(-)
diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h
index f96fa2df8f11..289e3576f56c 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/imx25-pinfunc.h
@@ -26,77 +26,77 @@
#define MX25_PAD_A13__GPIO_4_1 0x00c 0x22C 0x000 0x05 0x000
#define MX25_PAD_A13__LCDC_CLS 0x00c 0x22C 0x000 0x07 0x000
-#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x10 0x000
-#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x15 0x000
-#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x16 0x000
-#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x17 0x000
-
-#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x10 0x000
-#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x15 0x000
-#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x16 0x000
-#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x17 0x000
-
-#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x10 0x000
-#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x15 0x000
-#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x16 0x000
-#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x10 0x000
-#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x15 0x000
-#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x16 0x000
-#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x17 0x000
-
-#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x10 0x000
-#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x15 0x000
-#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x16 0x000
-#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x17 0x000
-
-#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x10 0x000
-#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x15 0x000
-#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x16 0x000
-#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x17 0x000
-
-#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x10 0x000
-#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x15 0x000
-#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x16 0x000
-#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x17 0x000
-
-#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x10 0x000
-#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x15 0x000
-#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x16 0x000
-#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x17 0x000
-
-#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x10 0x000
-#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x15 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x16 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x10 0x000
-#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x15 0x000
-#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x16 0x000
-#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x17 0x000
-
-#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x10 0x000
-#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x15 0x000
-#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x16 0x000
-#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x17 0x000
-
-#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x10 0x000
-#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x15 0x000
-#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x17 0x000
-
-#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x10 0x000
-#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x14 0x000
-#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x15 0x000
-
-#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x10 0x000
-#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x14 0x000
-#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x15 0x000
-
-#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x10 0x000
-#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x14 0x000
-#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x15 0x000
+#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x00 0x000
+#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x05 0x000
+#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x06 0x000
+#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x07 0x000
+
+#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x00 0x000
+#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x05 0x000
+#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x06 0x000
+#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x07 0x000
+
+#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x00 0x000
+#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x05 0x000
+#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x06 0x000
+#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x00 0x000
+#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x05 0x000
+#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x06 0x000
+#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x07 0x000
+
+#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x00 0x000
+#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x05 0x000
+#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x06 0x000
+#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x07 0x000
+
+#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x00 0x000
+#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x05 0x000
+#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x06 0x000
+#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x07 0x000
+
+#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x00 0x000
+#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x05 0x000
+#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x06 0x000
+#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x07 0x000
+
+#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x00 0x000
+#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x05 0x000
+#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x06 0x000
+#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x07 0x000
+
+#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x00 0x000
+#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x05 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x06 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x00 0x000
+#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x05 0x000
+#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x06 0x000
+#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x07 0x000
+
+#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x00 0x000
+#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x05 0x000
+#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x06 0x000
+#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x07 0x000
+
+#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x00 0x000
+#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x05 0x000
+#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x07 0x000
+
+#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x00 0x000
+#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x04 0x000
+#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x05 0x000
+
+#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x00 0x000
+#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x04 0x000
+#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x05 0x000
+
+#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x00 0x000
+#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x04 0x000
+#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x05 0x000
#define MX25_PAD_CS0__CS0 0x04c 0x000 0x000 0x00 0x000
#define MX25_PAD_CS0__GPIO_4_2 0x04c 0x000 0x000 0x05 0x000
@@ -105,51 +105,51 @@
#define MX25_PAD_CS1__NF_CE3 0x050 0x000 0x000 0x01 0x000
#define MX25_PAD_CS1__GPIO_4_3 0x050 0x000 0x000 0x05 0x000
-#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x10 0x000
+#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x00 0x000
#define MX25_PAD_CS4__NF_CE1 0x054 0x264 0x000 0x01 0x000
-#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x13 0x000
-#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x15 0x000
+#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x03 0x000
+#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x05 0x000
#define MX25_PAD_CS5__CS5 0x058 0x268 0x000 0x00 0x000
#define MX25_PAD_CS5__NF_CE2 0x058 0x268 0x000 0x01 0x000
#define MX25_PAD_CS5__UART5_RTS 0x058 0x268 0x574 0x03 0x000
#define MX25_PAD_CS5__GPIO_3_21 0x058 0x268 0x000 0x05 0x000
-#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x10 0x000
-#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x15 0x000
+#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x00 0x000
+#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x05 0x000
-#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x10 0x000
-#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x13 0x000
-#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x15 0x000
+#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x00 0x000
+#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x03 0x000
+#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x05 0x000
-#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x10 0x000
-#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x13 0x000
-#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x15 0x000
+#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x00 0x000
+#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x03 0x000
+#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x05 0x000
#define MX25_PAD_BCLK__BCLK 0x068 0x000 0x000 0x00 0x000
#define MX25_PAD_BCLK__GPIO_4_4 0x068 0x000 0x000 0x05 0x000
-#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x10 0x000
-#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x14 0x000
-#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x15 0x000
+#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x00 0x000
+#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x04 0x000
+#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x05 0x000
-#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x10 0x000
-#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x15 0x000
+#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x00 0x000
+#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x05 0x000
#define MX25_PAD_D15__D15 0x088 0x280 0x000 0x00 0x000
#define MX25_PAD_D15__LD16 0x088 0x280 0x000 0x01 0x000
@@ -210,101 +210,101 @@
#define MX25_PAD_D0__D0 0x0c4 0x2bc 0x000 0x00 0x000
#define MX25_PAD_D0__GPIO_4_20 0x0c4 0x2bc 0x000 0x05 0x000
-#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x10 0x000
-#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x12 0x000
-#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x15 0x000
+#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x00 0x000
+#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x02 0x000
+#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x05 0x000
-#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x10 0x000
-#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x12 0x000
-#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x15 0x000
+#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x00 0x000
+#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x02 0x000
+#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x05 0x000
-#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x10 0x000
-#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x15 0x000
+#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x00 0x000
+#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x05 0x000
-#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x10 0x000
-#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x15 0x000
+#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x00 0x000
+#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x05 0x000
-#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x10 0x000
-#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x15 0x000
+#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x00 0x000
+#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x05 0x000
-#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x10 0x000
-#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x15 0x000
+#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x00 0x000
+#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x05 0x000
-#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x10 0x000
-#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x15 0x000
+#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x00 0x000
+#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x05 0x000
-#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x10 0x000
-#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x15 0x000
+#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x00 0x000
+#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x05 0x000
-#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x10 0x000
-#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x12 0x000
-#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x15 0x000
+#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x00 0x000
+#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x02 0x000
+#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x05 0x000
#define MX25_PAD_LD8__SDHC2_CMD 0x0e8 0x2e0 0x4e0 0x06 0x000
-#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x10 0x000
-#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x12 0x000
-#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x15 0x001
+#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x00 0x000
+#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x02 0x000
+#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x05 0x001
#define MX25_PAD_LD9__SDHC2_CLK 0x0ec 0x2e4 0x4dc 0x06 0x000
#define MX25_PAD_LD10__LD10 0x0f0 0x2e8 0x000 0x00 0x000
#define MX25_PAD_LD10__UART4_RTS 0x0f0 0x2e8 0x56c 0x02 0x000
#define MX25_PAD_LD10__FEC_RX_ERR 0x0f0 0x2e8 0x518 0x05 0x001
-#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x10 0x000
-#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x12 0x000
-#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x15 0x001
+#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x00 0x000
+#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x02 0x000
+#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x05 0x001
#define MX25_PAD_LD11__SDHC2_DAT1 0x0f4 0x2ec 0x4e8 0x06 0x000
-#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x10 0x000
+#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x00 0x000
#define MX25_PAD_LD12__CSPI2_MOSI 0x0f8 0x2f0 0x4a0 0x02 0x000
-#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x15 0x001
+#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x05 0x001
-#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x10 0x000
+#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x00 0x000
#define MX25_PAD_LD13__CSPI2_MISO 0x0fc 0x2f4 0x49c 0x02 0x000
-#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x15 0x000
+#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x05 0x000
-#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x10 0x000
+#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x00 0x000
#define MX25_PAD_LD14__CSPI2_SCLK 0x100 0x2f8 0x494 0x02 0x000
-#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x15 0x000
+#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x05 0x000
-#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x10 0x000
+#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x00 0x000
#define MX25_PAD_LD15__CSPI2_RDY 0x104 0x2fc 0x498 0x02 0x000
-#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x15 0x001
+#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x05 0x001
-#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x10 0x000
-#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x15 0x000
+#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x00 0x000
+#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x05 0x000
-#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x10 0x000
-#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x15 0x000
+#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x00 0x000
+#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x05 0x000
-#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x10 0x000
-#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x15 0x000
+#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x00 0x000
+#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x05 0x000
-#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x10 0x000
+#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x00 0x000
#define MX25_PAD_OE_ACD__CSPI2_SS0 0x114 0x30c 0x4a4 0x02 0x000
-#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x15 0x000
+#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x05 0x000
-#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x10 0x000
-#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x11 0x000
-#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x14 0x000
-#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x15 0x001
-#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x16 0x000
+#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x00 0x000
+#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x01 0x000
+#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x04 0x000
+#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x05 0x001
+#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x06 0x000
-#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x10 0x000
-#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x15 0x000
-#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x16 0x001
+#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x00 0x000
+#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x05 0x000
+#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x06 0x001
-#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x10 0x000
-#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x11 0x001
+#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x00 0x000
+#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x01 0x001
#define MX25_PAD_CSI_D2__SIM1_CLK0 0x120 0x318 0x000 0x04 0x000
-#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x15 0x000
-#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x17 0x000
+#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x05 0x000
+#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x07 0x000
-#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x11 0x000
+#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x01 0x000
#define MX25_PAD_CSI_D3__SIM1_RST0 0x124 0x31c 0x000 0x04 0x000
-#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x15 0x000
-#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x17 0x001
+#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x05 0x000
+#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x07 0x001
#define MX25_PAD_CSI_D4__CSI_D4 0x128 0x320 0x000 0x00 0x000
#define MX25_PAD_CSI_D4__UART5_RTS 0x128 0x320 0x574 0x01 0x001
@@ -312,80 +312,80 @@
#define MX25_PAD_CSI_D4__GPIO_1_29 0x128 0x320 0x000 0x05 0x000
#define MX25_PAD_CSI_D4__CSPI3_SCLK 0x128 0x320 0x000 0x07 0x000
-#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x10 0x000
-#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x11 0x000
+#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x00 0x000
+#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x01 0x000
#define MX25_PAD_CSI_D5__SIM1_TX0 0x12c 0x324 0x000 0x04 0x000
-#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x15 0x000
-#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x17 0x000
+#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x05 0x000
+#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x07 0x000
-#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x10 0x000
-#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x12 0x001
+#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x00 0x000
+#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x02 0x001
#define MX25_PAD_CSI_D6__SIM1_PD0 0x130 0x328 0x000 0x04 0x000
-#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x15 0x000
+#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x05 0x000
-#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x12 0x001
-#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x15 0x000
+#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x02 0x001
+#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x05 0x000
-#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x10 0x000
-#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x12 0x000
-#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x15 0x000
-#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x17 0x000
+#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x00 0x000
+#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x02 0x000
+#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x05 0x000
+#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x07 0x000
-#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x10 0x000
-#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x12 0x000
-#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x15 0x000
-#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x17 0x000
+#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x00 0x000
+#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x02 0x000
+#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x05 0x000
+#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x07 0x000
-#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x10 0x000
-#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x11 0x000
-#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x12 0x001
-#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x15 0x000
+#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x00 0x000
+#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x01 0x000
+#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x02 0x001
+#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x05 0x000
-#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x10 0x000
-#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x11 0x000
-#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x12 0x001
-#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x15 0x000
+#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x00 0x000
+#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x01 0x000
+#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x02 0x001
+#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x05 0x000
-#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x10 0x000
-#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x11 0x000
-#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x12 0x001
-#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x15 0x000
+#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x00 0x000
+#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x01 0x000
+#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x02 0x001
+#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x05 0x000
-#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x10 0x000
-#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x11 0x000
-#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x12 0x001
-#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x15 0x000
+#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x00 0x000
+#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x01 0x000
+#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x02 0x001
+#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x05 0x000
-#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x10 0x000
-#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x15 0x000
+#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x00 0x000
+#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x05 0x000
-#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x10 0x000
-#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x15 0x000
+#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x00 0x000
+#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x12 0x000
-#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x02 0x000
+#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x05 0x000
#define MX25_PAD_CSPI1_SS1__CSPI1_SS1 0x164 0x35c 0x000 0x00 0x000
#define MX25_PAD_CSPI1_SS1__I2C3_DAT 0x164 0x35C 0x528 0x01 0x001
#define MX25_PAD_CSPI1_SS1__UART3_RTS 0x164 0x35c 0x000 0x02 0x000
#define MX25_PAD_CSPI1_SS1__GPIO_1_17 0x164 0x35c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x05 0x000
#define MX25_PAD_UART1_RXD__UART1_RXD 0x170 0x368 0x000 0x00 0x000
#define MX25_PAD_UART1_RXD__UART2_DTR 0x170 0x368 0x000 0x03 0x000
@@ -406,46 +406,46 @@
#define MX25_PAD_UART1_CTS__UART2_RI 0x17c 0x374 0x000 0x03 0x001
#define MX25_PAD_UART1_CTS__GPIO_4_25 0x17c 0x374 0x000 0x05 0x000
-#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x10 0x000
-#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x15 0x000
+#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x00 0x000
+#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x05 0x000
-#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x10 0x000
-#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x15 0x000
+#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x00 0x000
+#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x05 0x000
#define MX25_PAD_UART2_RTS__UART2_RTS 0x188 0x380 0x000 0x00 0x000
#define MX25_PAD_UART2_RTS__FEC_COL 0x188 0x380 0x504 0x02 0x002
#define MX25_PAD_UART2_RTS__CC1 0x188 0x380 0x000 0x03 0x000
#define MX25_PAD_UART2_RTS__GPIO_4_28 0x188 0x380 0x000 0x05 0x000
-#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x10 0x000
-#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x12 0x002
-#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000
+#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x00 0x000
+#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x02 0x002
+#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x05 0x000
-#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000
-#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x11 0x001
-#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x12 0x002
-#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x15 0x000
+#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x00 0x000
+#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x01 0x001
+#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x02 0x002
+#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x05 0x000
-#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x10 0x000
-#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x11 0x001
-#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x12 0x002
-#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x15 0x000
+#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x00 0x000
+#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x01 0x001
+#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x02 0x002
+#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x11 0x001
-#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x01 0x001
+#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x13 0x000
-#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x03 0x000
+#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x12 0x002
-#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x02 0x002
+#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x12 0x002
-#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x02 0x002
+#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x05 0x000
#define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x00 0x000
#define MX25_PAD_KPP_ROW0__UART3_RXD 0x1a8 0x3a0 0x568 0x01 0x001
@@ -469,123 +469,123 @@
#define MX25_PAD_KPP_ROW3__UART1_RI 0x1b4 0x3ac 0x000 0x04 0x000
#define MX25_PAD_KPP_ROW3__GPIO_3_0 0x1b4 0x3ac 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x11 0x001
-#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x01 0x001
+#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x05 0x000
#define MX25_PAD_KPP_COL2__KPP_COL2 0x1c0 0x3b8 0x000 0x00 0x000
#define MX25_PAD_KPP_COL2__UART4_RTS 0x1c0 0x3b8 0x56c 0x01 0x001
#define MX25_PAD_KPP_COL2__AUD5_TXC 0x1c0 0x3b8 0x000 0x02 0x000
#define MX25_PAD_KPP_COL2__GPIO_3_3 0x1c0 0x3b8 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x12 0x001
-#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x02 0x001
+#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x12 0x001
-#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x02 0x001
+#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x12 0x001
-#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x02 0x001
+#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x10 0x000
-#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x00 0x000
+#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x10 0x000
+#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_TX but that's wrong.
*/
-#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x14 0x000
-#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x04 0x000
+#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x05 0x000
-#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x10 0x000
+#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_RX but that's wrong.
*/
-#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x14 0x000
-#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x15 0x000
+#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x04 0x000
+#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x05 0x000
-#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x10 0x000
-#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x11 0x000
-#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x15 0x000
+#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x00 0x000
+#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x01 0x000
+#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x05 0x000
-#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x10 0x000
-#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x15 0x000
+#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x00 0x000
+#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x05 0x000
-#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x10 0x000
-#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x16 0x000
-#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x12 0x000
+#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x06 0x000
+#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x02 0x000
-#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x10 0x000
-#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x12 0x001
-#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001
+#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x02 0x001
+#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x06 0x001
-#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x10 0x000
-#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x11 0x000
-#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x12 0x001
-#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x13 0x001
-#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x16 0x000
+#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x01 0x000
+#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x02 0x001
+#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x03 0x001
+#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x06 0x000
-#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x10 0x000
-#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x12 0x001
-#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x16 0x001
+#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x02 0x001
+#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x06 0x001
-#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x10 0x000
-#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x11 0x002
-#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x12 0x000
-#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x14 0x000
-#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x16 0x002
+#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x01 0x002
+#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x02 0x000
+#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x04 0x000
+#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x06 0x002
-#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x10 0x000
-#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x12 0x000
-#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x14 0x000
-#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x16 0x000
+#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x02 0x000
+#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x04 0x000
+#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x06 0x000
-#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x10 0x000
-#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x15 0x000
+#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x00 0x000
+#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x05 0x000
-#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x10 0x000
-#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x15 0x000
+#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x00 0x000
+#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__VSTBY_REQ 0x214 0x408 0x000 0x00 0x000
#define MX25_PAD_VSTBY_REQ__AUD7_TXFS 0x214 0x408 0x000 0x04 0x000
#define MX25_PAD_VSTBY_REQ__GPIO_3_17 0x214 0x408 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__UART4_RTS 0x214 0x408 0x56c 0x06 0x002
-#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x10 0x000
-#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x15 0x000
+#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x00 0x000
+#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x05 0x000
-#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x10 0x000
-#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x14 0x001
-#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x15 0x000
-#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x16 0x000
+#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x00 0x000
+#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x04 0x001
+#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x05 0x000
+#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x06 0x000
-#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x10 0x000
-#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x15 0x000
+#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x00 0x000
+#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x05 0x000
#define MX25_PAD_BOOT_MODE0__BOOT_MODE0 0x224 0x000 0x000 0x00 0x000
#define MX25_PAD_BOOT_MODE0__GPIO_4_30 0x224 0x000 0x000 0x05 0x000
--
2.8.0.rc3
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-04-19 19:45 [PATCH] ARM: imx25-pinfunc: remove SION from all modes Uwe Kleine-König
@ 2016-04-19 21:19 ` Russell King - ARM Linux
2016-04-20 7:51 ` Uwe Kleine-König
2016-04-20 8:46 ` Lothar Waßmann
0 siblings, 2 replies; 12+ messages in thread
From: Russell King - ARM Linux @ 2016-04-19 21:19 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Apr 19, 2016 at 09:45:14PM +0200, Uwe Kleine-K?nig wrote:
> With the SION bit set a pin can be read as GPIO even though it's not muxed
> as GPIO. This is useful at times. The downside however is that the signal
> is not only routed to the GPIO IP but also all other IPs that can make use
> of the pin. This resulted in more than one issue for me in the past. Things
> like spi transfers that result in usb reenumeration or setting a GPIO to a
> value that triggers an RTS irq for an UART.
Isn't SION required for all GPIOs such that reading the value of a GPIO
pin returns the actual state of the pin, not the output value written
to it?
What about the ethernet pins? I know that on iMX6, SION is required for
correct functionality of certain phy clocking modes, and I wouldn't be
surprised if this was true in earlier designs as well.
--
RMK's Patch system: http://www.arm.linux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-04-19 21:19 ` Russell King - ARM Linux
@ 2016-04-20 7:51 ` Uwe Kleine-König
2016-04-20 8:46 ` Lothar Waßmann
1 sibling, 0 replies; 12+ messages in thread
From: Uwe Kleine-König @ 2016-04-20 7:51 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Apr 19, 2016 at 10:19:58PM +0100, Russell King - ARM Linux wrote:
> On Tue, Apr 19, 2016 at 09:45:14PM +0200, Uwe Kleine-K?nig wrote:
> > With the SION bit set a pin can be read as GPIO even though it's not muxed
> > as GPIO. This is useful at times. The downside however is that the signal
> > is not only routed to the GPIO IP but also all other IPs that can make use
> > of the pin. This resulted in more than one issue for me in the past. Things
> > like spi transfers that result in usb reenumeration or setting a GPIO to a
> > value that triggers an RTS irq for an UART.
>
> Isn't SION required for all GPIOs such that reading the value of a GPIO
> pin returns the actual state of the pin, not the output value written
> to it?
The documentation for the i.MX25 tells for the GPIO Data Register:
This register defines the value of the GPIO output when the
signal is configured as an output (GDIR[n]=1). Writes to this
register are stored in a register. Reading DR returns the value
stored in the register if the signal is configured as an output
(GDIR[n]=1), or the input signal's value if configured as an
input (GDIR[n]=0).
Note: The IOMUX must be configured to GPIO mode for the DR value
to connect with the signal. Reading the data register with the
input path disabled always returns a zero value.
And the gpio driver uses the GPIO Pad Status Register to implement
get_value, which has:
Each read-only bit of the PSR stores the value of the
corresponding input signal (as configured in the IOMUX).
I can confirm what's written in the manual on my i.MX25 machine:
# KPP_COL1: no pull, open drain disabled
barebox at i.MX25:/ mw 0x43fac3b4 0x0
# configure KPP_COL1 as GPIO_3_2, SION off
barebox at i.MX25:/ mw 0x43fac1bc 0x5
# set output to 0
barebox at i.MX25:/ mw 0x53fa4000 0xcddb8041
# configure GPIO_3_2 as output
barebox at i.MX25:/ mw 0x53fa4004 0x4
# both DR and PSR have 0:
barebox at i.MX25:/ md 0x53fa4000+12
53fa4000: cddba061 00000004 cddb8041 a.......A...
# set output to 1
barebox at i.MX25:/ mw 0x53fa4000 0xcddb8045
# DR reports 1, PSR has 0:
barebox at i.MX25:/ md 0x53fa4000+12
53fa4000: cddb8045 00000004 cddb8061 E.......a...
# now set SION:
barebox at i.MX25:/ mw 0x43fac1bc 0x15
# both, DR and PSR report 1
barebox at i.MX25:/ md 0x53fa4000+12
53fa4000: cddb8065 00000004 cddb8065 e.......e...
# set output to 0
barebox at i.MX25:/ mw 0x53fa4000 0xcddb8041
# both, DR and PSR report 0
barebox at i.MX25:/ md 0x53fa4000+12
53fa4000: cddba041 00000004 cddb8061 A.......a...
If I'm not mistaken, the gpio-mxc driver doesn't make use of SION
anyhow, because it uses BGPIOF_READ_OUTPUT_REG_SET (since commit
442b2494b17d ("gpio: mxc: read output value from GPIO_DR register")
which is included in 4.2-rc1).
> What about the ethernet pins? I know that on iMX6, SION is required for
> correct functionality of certain phy clocking modes, and I wouldn't be
> surprised if this was true in earlier designs as well.
I don't know the details, then maybe we should default to SION=0 and
give the board.dts a simple way to set it for selected pins.
I found
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-September/200949.html.
That's what you have in mind, right?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-04-19 21:19 ` Russell King - ARM Linux
2016-04-20 7:51 ` Uwe Kleine-König
@ 2016-04-20 8:46 ` Lothar Waßmann
2016-04-20 8:58 ` Uwe Kleine-König
1 sibling, 1 reply; 12+ messages in thread
From: Lothar Waßmann @ 2016-04-20 8:46 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Tue, 19 Apr 2016 22:19:58 +0100 Russell King - ARM Linux wrote:
> On Tue, Apr 19, 2016 at 09:45:14PM +0200, Uwe Kleine-K?nig wrote:
> > With the SION bit set a pin can be read as GPIO even though it's not muxed
> > as GPIO. This is useful at times. The downside however is that the signal
> > is not only routed to the GPIO IP but also all other IPs that can make use
> > of the pin. This resulted in more than one issue for me in the past. Things
> > like spi transfers that result in usb reenumeration or setting a GPIO to a
> > value that triggers an RTS irq for an UART.
>
> Isn't SION required for all GPIOs such that reading the value of a GPIO
> pin returns the actual state of the pin, not the output value written
> to it?
>
> What about the ethernet pins? I know that on iMX6, SION is required for
> correct functionality of certain phy clocking modes, and I wouldn't be
> surprised if this was true in earlier designs as well.
>
SION essentially makes any OUTPUT pin (GPIO or other function)
bidirectional.
Lothar Wa?mann
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-04-20 8:46 ` Lothar Waßmann
@ 2016-04-20 8:58 ` Uwe Kleine-König
2016-06-03 13:32 ` Uwe Kleine-König
0 siblings, 1 reply; 12+ messages in thread
From: Uwe Kleine-König @ 2016-04-20 8:58 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Apr 20, 2016 at 10:46:17AM +0200, Lothar Wa?mann wrote:
> Hi,
>
> On Tue, 19 Apr 2016 22:19:58 +0100 Russell King - ARM Linux wrote:
> > On Tue, Apr 19, 2016 at 09:45:14PM +0200, Uwe Kleine-K?nig wrote:
> > > With the SION bit set a pin can be read as GPIO even though it's not muxed
> > > as GPIO. This is useful at times. The downside however is that the signal
> > > is not only routed to the GPIO IP but also all other IPs that can make use
> > > of the pin. This resulted in more than one issue for me in the past. Things
> > > like spi transfers that result in usb reenumeration or setting a GPIO to a
> > > value that triggers an RTS irq for an UART.
> >
> > Isn't SION required for all GPIOs such that reading the value of a GPIO
> > pin returns the actual state of the pin, not the output value written
> > to it?
> >
> > What about the ethernet pins? I know that on iMX6, SION is required for
> > correct functionality of certain phy clocking modes, and I wouldn't be
> > surprised if this was true in earlier designs as well.
> >
> SION essentially makes any OUTPUT pin (GPIO or other function)
> bidirectional.
Yes, and the bad thing is that the input is routed to all modules that
the pin can be muxed for. So if on i.MX25 you intend to set the value of
gpio 3.21 you also toggle UART5's RTS signal with SION set.
And note that SION also has an effect on input pins (i.e. it is routed
to all modules instead of only the muxed one).
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-04-20 8:58 ` Uwe Kleine-König
@ 2016-06-03 13:32 ` Uwe Kleine-König
2016-06-03 14:01 ` Shawn Guo
0 siblings, 1 reply; 12+ messages in thread
From: Uwe Kleine-König @ 2016-06-03 13:32 UTC (permalink / raw)
To: linux-arm-kernel
Hello,
On Wed, Apr 20, 2016 at 10:58:39AM +0200, Uwe Kleine-K?nig wrote:
> On Wed, Apr 20, 2016 at 10:46:17AM +0200, Lothar Wa?mann wrote:
> > On Tue, 19 Apr 2016 22:19:58 +0100 Russell King - ARM Linux wrote:
> > > On Tue, Apr 19, 2016 at 09:45:14PM +0200, Uwe Kleine-K?nig wrote:
> > > > With the SION bit set a pin can be read as GPIO even though it's not muxed
> > > > as GPIO. This is useful at times. The downside however is that the signal
> > > > is not only routed to the GPIO IP but also all other IPs that can make use
> > > > of the pin. This resulted in more than one issue for me in the past. Things
> > > > like spi transfers that result in usb reenumeration or setting a GPIO to a
> > > > value that triggers an RTS irq for an UART.
> > >
> > > Isn't SION required for all GPIOs such that reading the value of a GPIO
> > > pin returns the actual state of the pin, not the output value written
> > > to it?
> > >
> > > What about the ethernet pins? I know that on iMX6, SION is required for
> > > correct functionality of certain phy clocking modes, and I wouldn't be
> > > surprised if this was true in earlier designs as well.
> > >
> > SION essentially makes any OUTPUT pin (GPIO or other function)
> > bidirectional.
>
> Yes, and the bad thing is that the input is routed to all modules that
> the pin can be muxed for. So if on i.MX25 you intend to set the value of
> gpio 3.21 you also toggle UART5's RTS signal with SION set.
>
> And note that SION also has an effect on input pins (i.e. it is routed
> to all modules instead of only the muxed one).
I found a regression of the patch under discussion (which was not
applied, so no big problem). On the custom mx25 based hardware an
SD-card isn't detected any more after removing SION from
MX25_PAD_SD1_CMD__SD1_CMD. I verified the same happens on a tx25.
Is this expected? IMHO it's unfortunate (if not a silicon bug) that you
need the SION bit here as the SION bit has some more side effects. If
you ask me, muxing a certain function for a pin should enable the input
path to the respective module if the pin is bidirectional.
Is there a list of pin/function pairs that need the SION bit set? Shawn,
would you agree to accept this patch with the high risk that it
introduces regressions? Or maybe we should make the SION bit more easily
overridable for board dts files (and default to off unless known it's
needed)?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-06-03 13:32 ` Uwe Kleine-König
@ 2016-06-03 14:01 ` Shawn Guo
2016-06-03 19:31 ` Uwe Kleine-König
0 siblings, 1 reply; 12+ messages in thread
From: Shawn Guo @ 2016-06-03 14:01 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 03, 2016 at 03:32:47PM +0200, Uwe Kleine-K?nig wrote:
> I found a regression of the patch under discussion (which was not
> applied, so no big problem). On the custom mx25 based hardware an
> SD-card isn't detected any more after removing SION from
> MX25_PAD_SD1_CMD__SD1_CMD. I verified the same happens on a tx25.
>
> Is this expected? IMHO it's unfortunate (if not a silicon bug) that you
> need the SION bit here as the SION bit has some more side effects. If
> you ask me, muxing a certain function for a pin should enable the input
> path to the respective module if the pin is bidirectional.
>
> Is there a list of pin/function pairs that need the SION bit set? Shawn,
> would you agree to accept this patch with the high risk that it
> introduces regressions? Or maybe we should make the SION bit more easily
> overridable for board dts files (and default to off unless known it's
> needed)?
I would be conservative on this. Can we just fix the SION bits that are
known doing harm?
Shawn
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-06-03 14:01 ` Shawn Guo
@ 2016-06-03 19:31 ` Uwe Kleine-König
2016-06-13 10:16 ` Uwe Kleine-König
0 siblings, 1 reply; 12+ messages in thread
From: Uwe Kleine-König @ 2016-06-03 19:31 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 03, 2016 at 10:01:07PM +0800, Shawn Guo wrote:
> On Fri, Jun 03, 2016 at 03:32:47PM +0200, Uwe Kleine-K?nig wrote:
> > I found a regression of the patch under discussion (which was not
> > applied, so no big problem). On the custom mx25 based hardware an
> > SD-card isn't detected any more after removing SION from
> > MX25_PAD_SD1_CMD__SD1_CMD. I verified the same happens on a tx25.
> >
> > Is this expected? IMHO it's unfortunate (if not a silicon bug) that you
> > need the SION bit here as the SION bit has some more side effects. If
> > you ask me, muxing a certain function for a pin should enable the input
> > path to the respective module if the pin is bidirectional.
> >
> > Is there a list of pin/function pairs that need the SION bit set? Shawn,
> > would you agree to accept this patch with the high risk that it
> > introduces regressions? Or maybe we should make the SION bit more easily
> > overridable for board dts files (and default to off unless known it's
> > needed)?
>
> I would be conservative on this. Can we just fix the SION bits that are
> known doing harm?
I didn't do any measurements, but I'd expect that every SION bit that is
set without good reason increases current consumption. So each SION bit
does some harm. Plus debugging a missing SION bit is much easier than a
SION bit that is set without need.
The first problem I debugged was an UART problem and the SION bit had to
be removed from MX25_PAD_KPP_ROW3__GPIO_3_0 (plus back then
MX25_PAD_KPP_ROW3__UART1_RI wasn't defined). The problem I had now was a
broken SD card and I had to add SION to MX25_PAD_SD1_CMD__SD1_CMD.
So I expect my commit to (maybe) introduce some obvious and easy to
debug regressions and to (probably) fix some harder to debug and not so
obvious problems. I'd say it's a net win.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-06-03 19:31 ` Uwe Kleine-König
@ 2016-06-13 10:16 ` Uwe Kleine-König
2016-06-13 10:17 ` [PATCH 1/2] ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD Uwe Kleine-König
2016-06-16 0:32 ` [PATCH] " Shawn Guo
0 siblings, 2 replies; 12+ messages in thread
From: Uwe Kleine-König @ 2016-06-13 10:16 UTC (permalink / raw)
To: linux-arm-kernel
Hello Shawn,
On Fri, Jun 03, 2016 at 09:31:48PM +0200, Uwe Kleine-K?nig wrote:
> On Fri, Jun 03, 2016 at 10:01:07PM +0800, Shawn Guo wrote:
> > On Fri, Jun 03, 2016 at 03:32:47PM +0200, Uwe Kleine-K?nig wrote:
> > > I found a regression of the patch under discussion (which was not
> > > applied, so no big problem). On the custom mx25 based hardware an
> > > SD-card isn't detected any more after removing SION from
> > > MX25_PAD_SD1_CMD__SD1_CMD. I verified the same happens on a tx25.
> > >
> > > Is this expected? IMHO it's unfortunate (if not a silicon bug) that you
> > > need the SION bit here as the SION bit has some more side effects. If
> > > you ask me, muxing a certain function for a pin should enable the input
> > > path to the respective module if the pin is bidirectional.
> > >
> > > Is there a list of pin/function pairs that need the SION bit set? Shawn,
> > > would you agree to accept this patch with the high risk that it
> > > introduces regressions? Or maybe we should make the SION bit more easily
> > > overridable for board dts files (and default to off unless known it's
> > > needed)?
> >
> > I would be conservative on this. Can we just fix the SION bits that are
> > known doing harm?
>
> I didn't do any measurements, but I'd expect that every SION bit that is
> set without good reason increases current consumption. So each SION bit
> does some harm. Plus debugging a missing SION bit is much easier than a
> SION bit that is set without need.
>
> The first problem I debugged was an UART problem and the SION bit had to
> be removed from MX25_PAD_KPP_ROW3__GPIO_3_0 (plus back then
> MX25_PAD_KPP_ROW3__UART1_RI wasn't defined). The problem I had now was a
> broken SD card and I had to add SION to MX25_PAD_SD1_CMD__SD1_CMD.
>
> So I expect my commit to (maybe) introduce some obvious and easy to
> debug regressions and to (probably) fix some harder to debug and not so
> obvious problems. I'd say it's a net win.
I didn't hear anything back from you on this topic. So I created a patch
that documents that SION is needed for MX25_PAD_SD1_CMD__SD1_CMD and
then rebased the patch under discussion on top of that. I will send the
resulting patches as reply to this mail. IMHO the first patch should not
be controversal.
I still think that the second patch is a good one, did your view change?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
2016-06-13 10:16 ` Uwe Kleine-König
@ 2016-06-13 10:17 ` Uwe Kleine-König
2016-06-13 10:17 ` [PATCH 2/2] ARM: imx25-pinfunc: remove SION from all modes Uwe Kleine-König
2016-06-16 0:32 ` [PATCH] " Shawn Guo
1 sibling, 1 reply; 12+ messages in thread
From: Uwe Kleine-König @ 2016-06-13 10:17 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
---
arch/arm/boot/dts/imx25-pinfunc.h | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h
index f96fa2df8f11..953e646f3ea1 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/imx25-pinfunc.h
@@ -421,6 +421,15 @@
#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x12 0x002
#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000
+/*
+ * Removing the SION bit from MX25_PAD_SD1_CMD__SD1_CMD breaks detecting an SD
+ * card. According to the i.MX25 reference manual (e.g. Figure 23-2 in IMX25RM
+ * Rev. 2 from 01/2011) this pin is bidirectional. So it seems to be a silicon
+ * bug that configuring the SD1_CMD function doesn't enable the input path for
+ * this pin.
+ * This might have side effects for other hardware units that are connected to
+ * that pin and use the respective function as input.
+ */
#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000
#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x11 0x001
#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x12 0x002
--
2.8.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] ARM: imx25-pinfunc: remove SION from all modes
2016-06-13 10:17 ` [PATCH 1/2] ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD Uwe Kleine-König
@ 2016-06-13 10:17 ` Uwe Kleine-König
0 siblings, 0 replies; 12+ messages in thread
From: Uwe Kleine-König @ 2016-06-13 10:17 UTC (permalink / raw)
To: linux-arm-kernel
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed that are not known to be needed.
Note that this has no influence on GPIOs under Linux as the gpio-mxc
driver just reports the level the pin is driven to for outputs and not
the level as seen on the pin.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
---
arch/arm/boot/dts/imx25-pinfunc.h | 618 +++++++++++++++++++-------------------
1 file changed, 309 insertions(+), 309 deletions(-)
diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h
index 953e646f3ea1..f840f03ad171 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/imx25-pinfunc.h
@@ -26,77 +26,77 @@
#define MX25_PAD_A13__GPIO_4_1 0x00c 0x22C 0x000 0x05 0x000
#define MX25_PAD_A13__LCDC_CLS 0x00c 0x22C 0x000 0x07 0x000
-#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x10 0x000
-#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x15 0x000
-#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x16 0x000
-#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x17 0x000
-
-#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x10 0x000
-#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x15 0x000
-#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x16 0x000
-#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x17 0x000
-
-#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x10 0x000
-#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x15 0x000
-#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x16 0x000
-#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x10 0x000
-#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x15 0x000
-#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x16 0x000
-#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x17 0x000
-
-#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x10 0x000
-#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x15 0x000
-#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x16 0x000
-#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x17 0x000
-
-#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x10 0x000
-#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x15 0x000
-#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x16 0x000
-#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x17 0x000
-
-#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x10 0x000
-#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x15 0x000
-#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x16 0x000
-#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x17 0x000
-
-#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x10 0x000
-#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x15 0x000
-#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x16 0x000
-#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x17 0x000
-
-#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x10 0x000
-#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x15 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x16 0x000
-#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000
-
-#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x10 0x000
-#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x15 0x000
-#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x16 0x000
-#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x17 0x000
-
-#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x10 0x000
-#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x15 0x000
-#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x16 0x000
-#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x17 0x000
-
-#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x10 0x000
-#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x15 0x000
-#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x17 0x000
-
-#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x10 0x000
-#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x14 0x000
-#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x15 0x000
-
-#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x10 0x000
-#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x14 0x000
-#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x15 0x000
-
-#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x10 0x000
-#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x14 0x000
-#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x15 0x000
+#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x00 0x000
+#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x05 0x000
+#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x06 0x000
+#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x07 0x000
+
+#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x00 0x000
+#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x05 0x000
+#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x06 0x000
+#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x07 0x000
+
+#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x00 0x000
+#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x05 0x000
+#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x06 0x000
+#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x00 0x000
+#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x05 0x000
+#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x06 0x000
+#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x07 0x000
+
+#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x00 0x000
+#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x05 0x000
+#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x06 0x000
+#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x07 0x000
+
+#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x00 0x000
+#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x05 0x000
+#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x06 0x000
+#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x07 0x000
+
+#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x00 0x000
+#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x05 0x000
+#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x06 0x000
+#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x07 0x000
+
+#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x00 0x000
+#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x05 0x000
+#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x06 0x000
+#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x07 0x000
+
+#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x00 0x000
+#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x05 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x06 0x000
+#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x07 0x000
+
+#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x00 0x000
+#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x05 0x000
+#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x06 0x000
+#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x07 0x000
+
+#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x00 0x000
+#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x05 0x000
+#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x06 0x000
+#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x07 0x000
+
+#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x00 0x000
+#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x05 0x000
+#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x07 0x000
+
+#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x00 0x000
+#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x04 0x000
+#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x05 0x000
+
+#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x00 0x000
+#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x04 0x000
+#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x05 0x000
+
+#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x00 0x000
+#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x04 0x000
+#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x05 0x000
#define MX25_PAD_CS0__CS0 0x04c 0x000 0x000 0x00 0x000
#define MX25_PAD_CS0__GPIO_4_2 0x04c 0x000 0x000 0x05 0x000
@@ -105,51 +105,51 @@
#define MX25_PAD_CS1__NF_CE3 0x050 0x000 0x000 0x01 0x000
#define MX25_PAD_CS1__GPIO_4_3 0x050 0x000 0x000 0x05 0x000
-#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x10 0x000
+#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x00 0x000
#define MX25_PAD_CS4__NF_CE1 0x054 0x264 0x000 0x01 0x000
-#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x13 0x000
-#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x15 0x000
+#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x03 0x000
+#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x05 0x000
#define MX25_PAD_CS5__CS5 0x058 0x268 0x000 0x00 0x000
#define MX25_PAD_CS5__NF_CE2 0x058 0x268 0x000 0x01 0x000
#define MX25_PAD_CS5__UART5_RTS 0x058 0x268 0x574 0x03 0x000
#define MX25_PAD_CS5__GPIO_3_21 0x058 0x268 0x000 0x05 0x000
-#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x10 0x000
-#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x15 0x000
+#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x00 0x000
+#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x05 0x000
-#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x10 0x000
-#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x13 0x000
-#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x15 0x000
+#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x00 0x000
+#define MX25_PAD_ECB__UART5_TXD 0x060 0x270 0x000 0x03 0x000
+#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x05 0x000
-#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x10 0x000
-#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x13 0x000
-#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x15 0x000
+#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x00 0x000
+#define MX25_PAD_LBA__UART5_RXD 0x064 0x274 0x578 0x03 0x000
+#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x05 0x000
#define MX25_PAD_BCLK__BCLK 0x068 0x000 0x000 0x00 0x000
#define MX25_PAD_BCLK__GPIO_4_4 0x068 0x000 0x000 0x05 0x000
-#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x10 0x000
-#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x14 0x000
-#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x15 0x000
+#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x00 0x000
+#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x04 0x000
+#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x05 0x000
-#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x10 0x000
-#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x15 0x000
+#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x00 0x000
+#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x05 0x000
-#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x10 0x000
-#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x15 0x000
+#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x00 0x000
+#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x05 0x000
#define MX25_PAD_D15__D15 0x088 0x280 0x000 0x00 0x000
#define MX25_PAD_D15__LD16 0x088 0x280 0x000 0x01 0x000
@@ -210,101 +210,101 @@
#define MX25_PAD_D0__D0 0x0c4 0x2bc 0x000 0x00 0x000
#define MX25_PAD_D0__GPIO_4_20 0x0c4 0x2bc 0x000 0x05 0x000
-#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x10 0x000
-#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x12 0x000
-#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x15 0x000
+#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x00 0x000
+#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x02 0x000
+#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x05 0x000
-#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x10 0x000
-#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x12 0x000
-#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x15 0x000
+#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x00 0x000
+#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x02 0x000
+#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x05 0x000
-#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x10 0x000
-#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x15 0x000
+#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x00 0x000
+#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x05 0x000
-#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x10 0x000
-#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x15 0x000
+#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x00 0x000
+#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x05 0x000
-#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x10 0x000
-#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x15 0x000
+#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x00 0x000
+#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x05 0x000
-#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x10 0x000
-#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x15 0x000
+#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x00 0x000
+#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x05 0x000
-#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x10 0x000
-#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x15 0x000
+#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x00 0x000
+#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x05 0x000
-#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x10 0x000
-#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x15 0x000
+#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x00 0x000
+#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x05 0x000
-#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x10 0x000
-#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x12 0x000
-#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x15 0x000
+#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x00 0x000
+#define MX25_PAD_LD8__UART4_RXD 0x0e8 0x2e0 0x570 0x02 0x000
+#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x05 0x000
#define MX25_PAD_LD8__SDHC2_CMD 0x0e8 0x2e0 0x4e0 0x06 0x000
-#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x10 0x000
-#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x12 0x000
-#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x15 0x001
+#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x00 0x000
+#define MX25_PAD_LD9__UART4_TXD 0x0ec 0x2e4 0x000 0x02 0x000
+#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x05 0x001
#define MX25_PAD_LD9__SDHC2_CLK 0x0ec 0x2e4 0x4dc 0x06 0x000
#define MX25_PAD_LD10__LD10 0x0f0 0x2e8 0x000 0x00 0x000
#define MX25_PAD_LD10__UART4_RTS 0x0f0 0x2e8 0x56c 0x02 0x000
#define MX25_PAD_LD10__FEC_RX_ERR 0x0f0 0x2e8 0x518 0x05 0x001
-#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x10 0x000
-#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x12 0x000
-#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x15 0x001
+#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x00 0x000
+#define MX25_PAD_LD11__UART4_CTS 0x0f4 0x2ec 0x000 0x02 0x000
+#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x05 0x001
#define MX25_PAD_LD11__SDHC2_DAT1 0x0f4 0x2ec 0x4e8 0x06 0x000
-#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x10 0x000
+#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x00 0x000
#define MX25_PAD_LD12__CSPI2_MOSI 0x0f8 0x2f0 0x4a0 0x02 0x000
-#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x15 0x001
+#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x05 0x001
-#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x10 0x000
+#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x00 0x000
#define MX25_PAD_LD13__CSPI2_MISO 0x0fc 0x2f4 0x49c 0x02 0x000
-#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x15 0x000
+#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x05 0x000
-#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x10 0x000
+#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x00 0x000
#define MX25_PAD_LD14__CSPI2_SCLK 0x100 0x2f8 0x494 0x02 0x000
-#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x15 0x000
+#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x05 0x000
-#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x10 0x000
+#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x00 0x000
#define MX25_PAD_LD15__CSPI2_RDY 0x104 0x2fc 0x498 0x02 0x000
-#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x15 0x001
+#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x05 0x001
-#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x10 0x000
-#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x15 0x000
+#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x00 0x000
+#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x05 0x000
-#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x10 0x000
-#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x15 0x000
+#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x00 0x000
+#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x05 0x000
-#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x10 0x000
-#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x15 0x000
+#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x00 0x000
+#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x05 0x000
-#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x10 0x000
+#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x00 0x000
#define MX25_PAD_OE_ACD__CSPI2_SS0 0x114 0x30c 0x4a4 0x02 0x000
-#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x15 0x000
+#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x05 0x000
-#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x10 0x000
-#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x11 0x000
-#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x14 0x000
-#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x15 0x001
-#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x16 0x000
+#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x00 0x000
+#define MX25_PAD_CONTRAST__CC4 0x118 0x310 0x000 0x01 0x000
+#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x04 0x000
+#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x05 0x001
+#define MX25_PAD_CONTRAST__USBH2_PWR 0x118 0x310 0x000 0x06 0x000
-#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x10 0x000
-#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x15 0x000
-#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x16 0x001
+#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x00 0x000
+#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x05 0x000
+#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x06 0x001
-#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x10 0x000
-#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x11 0x001
+#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x00 0x000
+#define MX25_PAD_CSI_D2__UART5_RXD 0x120 0x318 0x578 0x01 0x001
#define MX25_PAD_CSI_D2__SIM1_CLK0 0x120 0x318 0x000 0x04 0x000
-#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x15 0x000
-#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x17 0x000
+#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x05 0x000
+#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x07 0x000
-#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x11 0x000
+#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D3__UART5_TXD 0x124 0x31c 0x000 0x01 0x000
#define MX25_PAD_CSI_D3__SIM1_RST0 0x124 0x31c 0x000 0x04 0x000
-#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x15 0x000
-#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x17 0x001
+#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x05 0x000
+#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x07 0x001
#define MX25_PAD_CSI_D4__CSI_D4 0x128 0x320 0x000 0x00 0x000
#define MX25_PAD_CSI_D4__UART5_RTS 0x128 0x320 0x574 0x01 0x001
@@ -312,80 +312,80 @@
#define MX25_PAD_CSI_D4__GPIO_1_29 0x128 0x320 0x000 0x05 0x000
#define MX25_PAD_CSI_D4__CSPI3_SCLK 0x128 0x320 0x000 0x07 0x000
-#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x10 0x000
-#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x11 0x000
+#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x00 0x000
+#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x01 0x000
#define MX25_PAD_CSI_D5__SIM1_TX0 0x12c 0x324 0x000 0x04 0x000
-#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x15 0x000
-#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x17 0x000
+#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x05 0x000
+#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x07 0x000
-#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x10 0x000
-#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x12 0x001
+#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x00 0x000
+#define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x02 0x001
#define MX25_PAD_CSI_D6__SIM1_PD0 0x130 0x328 0x000 0x04 0x000
-#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x15 0x000
+#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x05 0x000
-#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x10 0x000
-#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x12 0x001
-#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x15 0x000
+#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x00 0x000
+#define MX25_PAD_CSI_D7__SDHC2_DAT_CLK 0x134 0x32C 0x4dc 0x02 0x001
+#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x05 0x000
-#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x10 0x000
-#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x12 0x000
-#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x15 0x000
-#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x17 0x000
+#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x00 0x000
+#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x02 0x000
+#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x05 0x000
+#define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x07 0x000
-#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x10 0x000
-#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x12 0x000
-#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x15 0x000
-#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x17 0x000
+#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x00 0x000
+#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x02 0x000
+#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x05 0x000
+#define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x07 0x000
-#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x10 0x000
-#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x11 0x000
-#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x12 0x001
-#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x15 0x000
+#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x00 0x000
+#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x01 0x000
+#define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x02 0x001
+#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x05 0x000
-#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x10 0x000
-#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x11 0x000
-#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x12 0x001
-#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x15 0x000
+#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x00 0x000
+#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x01 0x000
+#define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x02 0x001
+#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x05 0x000
-#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x10 0x000
-#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x11 0x000
-#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x12 0x001
-#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x15 0x000
+#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x00 0x000
+#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x01 0x000
+#define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x02 0x001
+#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x05 0x000
-#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x10 0x000
-#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x11 0x000
-#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x12 0x001
-#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x15 0x000
+#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x00 0x000
+#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x01 0x000
+#define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x02 0x001
+#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x05 0x000
-#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x10 0x000
-#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x15 0x000
+#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x00 0x000
+#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x05 0x000
-#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x10 0x000
-#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x15 0x000
+#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x00 0x000
+#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x12 0x000
-#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MOSI__UART3_RXD 0x158 0x350 0x568 0x02 0x000
+#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_MISO__UART3_TXD 0x15c 0x354 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SS0__PWM2_PWMO 0x160 0x358 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x05 0x000
#define MX25_PAD_CSPI1_SS1__CSPI1_SS1 0x164 0x35c 0x000 0x00 0x000
#define MX25_PAD_CSPI1_SS1__I2C3_DAT 0x164 0x35C 0x528 0x01 0x001
#define MX25_PAD_CSPI1_SS1__UART3_RTS 0x164 0x35c 0x000 0x02 0x000
#define MX25_PAD_CSPI1_SS1__GPIO_1_17 0x164 0x35c 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x12 0x000
-#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_SCLK__UART3_CTS 0x168 0x360 0x000 0x02 0x000
+#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x05 0x000
-#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x10 0x000
-#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x15 0x000
+#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x00 0x000
+#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x05 0x000
#define MX25_PAD_UART1_RXD__UART1_RXD 0x170 0x368 0x000 0x00 0x000
#define MX25_PAD_UART1_RXD__UART2_DTR 0x170 0x368 0x000 0x03 0x000
@@ -406,20 +406,20 @@
#define MX25_PAD_UART1_CTS__UART2_RI 0x17c 0x374 0x000 0x03 0x001
#define MX25_PAD_UART1_CTS__GPIO_4_25 0x17c 0x374 0x000 0x05 0x000
-#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x10 0x000
-#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x15 0x000
+#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x00 0x000
+#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x05 0x000
-#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x10 0x000
-#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x15 0x000
+#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x00 0x000
+#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x05 0x000
#define MX25_PAD_UART2_RTS__UART2_RTS 0x188 0x380 0x000 0x00 0x000
#define MX25_PAD_UART2_RTS__FEC_COL 0x188 0x380 0x504 0x02 0x002
#define MX25_PAD_UART2_RTS__CC1 0x188 0x380 0x000 0x03 0x000
#define MX25_PAD_UART2_RTS__GPIO_4_28 0x188 0x380 0x000 0x05 0x000
-#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x10 0x000
-#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x12 0x002
-#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000
+#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x00 0x000
+#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x02 0x002
+#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x05 0x000
/*
* Removing the SION bit from MX25_PAD_SD1_CMD__SD1_CMD breaks detecting an SD
@@ -431,30 +431,30 @@
* that pin and use the respective function as input.
*/
#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000
-#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x11 0x001
-#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x12 0x002
-#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x15 0x000
+#define MX25_PAD_SD1_CMD__CSPI2_MOSI 0x190 0x388 0x4a0 0x01 0x001
+#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x02 0x002
+#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x05 0x000
-#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x10 0x000
-#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x11 0x001
-#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x12 0x002
-#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x15 0x000
+#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x00 0x000
+#define MX25_PAD_SD1_CLK__CSPI2_MISO 0x194 0x38c 0x49c 0x01 0x001
+#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x02 0x002
+#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x11 0x001
-#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA0__CSPI2_SCLK 0x198 0x390 0x494 0x01 0x001
+#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x13 0x000
-#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x03 0x000
+#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x12 0x002
-#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x02 0x002
+#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x05 0x000
-#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x10 0x000
-#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x12 0x002
-#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000
+#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x00 0x000
+#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x02 0x002
+#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x05 0x000
#define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x00 0x000
#define MX25_PAD_KPP_ROW0__UART3_RXD 0x1a8 0x3a0 0x568 0x01 0x001
@@ -478,123 +478,123 @@
#define MX25_PAD_KPP_ROW3__UART1_RI 0x1b4 0x3ac 0x000 0x04 0x000
#define MX25_PAD_KPP_ROW3__GPIO_3_0 0x1b4 0x3ac 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x11 0x001
-#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL0__UART4_RXD 0x1b8 0x3b0 0x570 0x01 0x001
+#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL1__UART4_TXD 0x1bc 0x3b4 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x05 0x000
#define MX25_PAD_KPP_COL2__KPP_COL2 0x1c0 0x3b8 0x000 0x00 0x000
#define MX25_PAD_KPP_COL2__UART4_RTS 0x1c0 0x3b8 0x56c 0x01 0x001
#define MX25_PAD_KPP_COL2__AUD5_TXC 0x1c0 0x3b8 0x000 0x02 0x000
#define MX25_PAD_KPP_COL2__GPIO_3_3 0x1c0 0x3b8 0x000 0x05 0x000
-#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x10 0x000
-#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x11 0x000
-#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x12 0x000
-#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x15 0x000
+#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x00 0x000
+#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x01 0x000
+#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x02 0x000
+#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x12 0x001
-#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x02 0x001
+#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x05 0x000
-#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x10 0x000
-#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x12 0x001
-#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x15 0x000
+#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x00 0x000
+#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x02 0x001
+#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x05 0x000
-#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x10 0x000
-#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x12 0x001
-#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x15 0x000
+#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x00 0x000
+#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x02 0x001
+#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x10 0x000
-#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x00 0x000
+#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x05 0x000
-#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x10 0x000
+#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_TX but that's wrong.
*/
-#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x14 0x000
-#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x15 0x000
+#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x04 0x000
+#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x05 0x000
-#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x10 0x000
+#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x00 0x000
/*
* According to the i.MX25 Reference manual (IMX25RM, Rev. 2,
* 01/2011) this is CAN1_RX but that's wrong.
*/
-#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x14 0x000
-#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x15 0x000
+#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x04 0x000
+#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x05 0x000
-#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x10 0x000
-#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x15 0x000
+#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x00 0x000
+#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x05 0x000
-#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x10 0x000
-#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x11 0x000
-#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x15 0x000
+#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x00 0x000
+#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x01 0x000
+#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x05 0x000
-#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x10 0x000
-#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x15 0x000
+#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x00 0x000
+#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x05 0x000
-#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x10 0x000
-#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x16 0x000
-#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x12 0x000
+#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x06 0x000
+#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x02 0x000
-#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x10 0x000
-#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x12 0x001
-#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001
+#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x02 0x001
+#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x06 0x001
-#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x10 0x000
-#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x11 0x000
-#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x12 0x001
-#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x13 0x001
-#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x16 0x000
+#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x01 0x000
+#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x02 0x001
+#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x03 0x001
+#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x06 0x000
-#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x10 0x000
-#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x12 0x001
-#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x16 0x001
+#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x02 0x001
+#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x06 0x001
-#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x10 0x000
-#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x11 0x002
-#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x12 0x000
-#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x14 0x000
-#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x16 0x002
+#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x01 0x002
+#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x02 0x000
+#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x04 0x000
+#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x06 0x002
-#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x10 0x000
-#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x12 0x000
-#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x14 0x000
-#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x16 0x000
+#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x02 0x000
+#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x04 0x000
+#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x06 0x000
-#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x10 0x000
-#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x15 0x000
+#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x00 0x000
+#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x05 0x000
-#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x10 0x000
-#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x15 0x000
+#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x00 0x000
+#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__VSTBY_REQ 0x214 0x408 0x000 0x00 0x000
#define MX25_PAD_VSTBY_REQ__AUD7_TXFS 0x214 0x408 0x000 0x04 0x000
#define MX25_PAD_VSTBY_REQ__GPIO_3_17 0x214 0x408 0x000 0x05 0x000
#define MX25_PAD_VSTBY_REQ__UART4_RTS 0x214 0x408 0x56c 0x06 0x002
-#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x10 0x000
-#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x15 0x000
+#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x00 0x000
+#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x05 0x000
-#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x10 0x000
-#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x14 0x001
-#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x15 0x000
-#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x16 0x000
+#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x00 0x000
+#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x04 0x001
+#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x05 0x000
+#define MX25_PAD_POWER_FAIL__UART4_CTS 0x21c 0x410 0x000 0x06 0x000
-#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x10 0x000
-#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x15 0x000
+#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x00 0x000
+#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x05 0x000
#define MX25_PAD_BOOT_MODE0__BOOT_MODE0 0x224 0x000 0x000 0x00 0x000
#define MX25_PAD_BOOT_MODE0__GPIO_4_30 0x224 0x000 0x000 0x05 0x000
--
2.8.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH] ARM: imx25-pinfunc: remove SION from all modes
2016-06-13 10:16 ` Uwe Kleine-König
2016-06-13 10:17 ` [PATCH 1/2] ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD Uwe Kleine-König
@ 2016-06-16 0:32 ` Shawn Guo
1 sibling, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2016-06-16 0:32 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Jun 13, 2016 at 12:16:16PM +0200, Uwe Kleine-K?nig wrote:
> Hello Shawn,
>
> On Fri, Jun 03, 2016 at 09:31:48PM +0200, Uwe Kleine-K?nig wrote:
> > On Fri, Jun 03, 2016 at 10:01:07PM +0800, Shawn Guo wrote:
> > > On Fri, Jun 03, 2016 at 03:32:47PM +0200, Uwe Kleine-K?nig wrote:
> > > > I found a regression of the patch under discussion (which was not
> > > > applied, so no big problem). On the custom mx25 based hardware an
> > > > SD-card isn't detected any more after removing SION from
> > > > MX25_PAD_SD1_CMD__SD1_CMD. I verified the same happens on a tx25.
> > > >
> > > > Is this expected? IMHO it's unfortunate (if not a silicon bug) that you
> > > > need the SION bit here as the SION bit has some more side effects. If
> > > > you ask me, muxing a certain function for a pin should enable the input
> > > > path to the respective module if the pin is bidirectional.
> > > >
> > > > Is there a list of pin/function pairs that need the SION bit set? Shawn,
> > > > would you agree to accept this patch with the high risk that it
> > > > introduces regressions? Or maybe we should make the SION bit more easily
> > > > overridable for board dts files (and default to off unless known it's
> > > > needed)?
> > >
> > > I would be conservative on this. Can we just fix the SION bits that are
> > > known doing harm?
> >
> > I didn't do any measurements, but I'd expect that every SION bit that is
> > set without good reason increases current consumption. So each SION bit
> > does some harm. Plus debugging a missing SION bit is much easier than a
> > SION bit that is set without need.
> >
> > The first problem I debugged was an UART problem and the SION bit had to
> > be removed from MX25_PAD_KPP_ROW3__GPIO_3_0 (plus back then
> > MX25_PAD_KPP_ROW3__UART1_RI wasn't defined). The problem I had now was a
> > broken SD card and I had to add SION to MX25_PAD_SD1_CMD__SD1_CMD.
> >
> > So I expect my commit to (maybe) introduce some obvious and easy to
> > debug regressions and to (probably) fix some harder to debug and not so
> > obvious problems. I'd say it's a net win.
>
> I didn't hear anything back from you on this topic. So I created a patch
> that documents that SION is needed for MX25_PAD_SD1_CMD__SD1_CMD and
> then rebased the patch under discussion on top of that. I will send the
> resulting patches as reply to this mail. IMHO the first patch should not
> be controversal.
>
> I still think that the second patch is a good one, did your view change?
Okay, I chose to trust you and applied both patches :)
Shawn
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2016-06-16 0:32 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-04-19 19:45 [PATCH] ARM: imx25-pinfunc: remove SION from all modes Uwe Kleine-König
2016-04-19 21:19 ` Russell King - ARM Linux
2016-04-20 7:51 ` Uwe Kleine-König
2016-04-20 8:46 ` Lothar Waßmann
2016-04-20 8:58 ` Uwe Kleine-König
2016-06-03 13:32 ` Uwe Kleine-König
2016-06-03 14:01 ` Shawn Guo
2016-06-03 19:31 ` Uwe Kleine-König
2016-06-13 10:16 ` Uwe Kleine-König
2016-06-13 10:17 ` [PATCH 1/2] ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD Uwe Kleine-König
2016-06-13 10:17 ` [PATCH 2/2] ARM: imx25-pinfunc: remove SION from all modes Uwe Kleine-König
2016-06-16 0:32 ` [PATCH] " Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.