[PATCH 0/3] Update pm8941 spmi regulators for USB OTG

[PATCH 0/3] Update pm8941 spmi regulators for USB OTG

[Stephen Boyd]

While rewriting the USB support for MSM SoCs I ran into a few
minor bugs with the pm8941 regulator driver that hadn't been found
before. These patches are part of a larger series that allows me
to get proper USB OTG support working on the apq8074 dragonboard.

Stephen Boyd (3):
  regulator: qcom_spmi: Add support for S4 supply on pm8941
  regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941
  regulator: qcom_spmi: Add support for get_mode/set_mode on switches

 .../devicetree/bindings/regulator/qcom,spmi-regulator.txt          | 6 +++---
 drivers/regulator/qcom_spmi-regulator.c                            | 7 +++++--
 2 files changed, 8 insertions(+), 5 deletions(-)

-- 
2.9.0.rc2.8.ga28705d

[PATCH 0/3] Update pm8941 spmi regulators for USB OTG

[Stephen Boyd]

While rewriting the USB support for MSM SoCs I ran into a few
minor bugs with the pm8941 regulator driver that hadn't been found
before. These patches are part of a larger series that allows me
to get proper USB OTG support working on the apq8074 dragonboard.

Stephen Boyd (3):
  regulator: qcom_spmi: Add support for S4 supply on pm8941
  regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941
  regulator: qcom_spmi: Add support for get_mode/set_mode on switches

 .../devicetree/bindings/regulator/qcom,spmi-regulator.txt          | 6 +++---
 drivers/regulator/qcom_spmi-regulator.c                            | 7 +++++--
 2 files changed, 8 insertions(+), 5 deletions(-)

-- 
2.9.0.rc2.8.ga28705d

[PATCH 1/3] regulator: qcom_spmi: Add support for S4 supply on pm8941

[Stephen Boyd]

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++--
 drivers/regulator/qcom_spmi-regulator.c                             | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 46c6f3ed1a1c..3e827bb9a56d 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -113,8 +113,8 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
 	mvs1, mvs2
 
 pm8994:
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 84cce21e98cd..fe09407b150b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1496,6 +1496,7 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "s1", 0x1400, "vdd_s1", },
 	{ "s2", 0x1700, "vdd_s2", },
 	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0xa000, },
 	{ "l1", 0x4000, "vdd_l1_l3", },
 	{ "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
 	{ "l3", 0x4200, "vdd_l1_l3", },
-- 
2.9.0.rc2.8.ga28705d

[PATCH 1/3] regulator: qcom_spmi: Add support for S4 supply on pm8941

[Stephen Boyd]

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++--
 drivers/regulator/qcom_spmi-regulator.c                             | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 46c6f3ed1a1c..3e827bb9a56d 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -113,8 +113,8 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
 	mvs1, mvs2
 
 pm8994:
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 84cce21e98cd..fe09407b150b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1496,6 +1496,7 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "s1", 0x1400, "vdd_s1", },
 	{ "s2", 0x1700, "vdd_s2", },
 	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0xa000, },
 	{ "l1", 0x4000, "vdd_l1_l3", },
 	{ "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
 	{ "l3", 0x4200, "vdd_l1_l3", },
-- 
2.9.0.rc2.8.ga28705d

[PATCH 2/3] regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

[Stephen Boyd]

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 2 +-
 drivers/regulator/qcom_spmi-regulator.c                             | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 3e827bb9a56d..0fa3b0fac129 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -115,7 +115,7 @@ pm8916:
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	5vs1, 5vs2
 
 pm8994:
 	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fe09407b150b..43f8f20b82e9 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1524,8 +1524,8 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
 	{ "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
 	{ "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
-	{ "mvs1", 0x8300, "vin_5vs", },
-	{ "mvs2", 0x8400, "vin_5vs", },
+	{ "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", },
+	{ "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", },
 	{ }
 };
 
-- 
2.9.0.rc2.8.ga28705d

[PATCH 2/3] regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

[Stephen Boyd]

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 2 +-
 drivers/regulator/qcom_spmi-regulator.c                             | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 3e827bb9a56d..0fa3b0fac129 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -115,7 +115,7 @@ pm8916:
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	5vs1, 5vs2
 
 pm8994:
 	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fe09407b150b..43f8f20b82e9 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1524,8 +1524,8 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
 	{ "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
 	{ "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
-	{ "mvs1", 0x8300, "vin_5vs", },
-	{ "mvs2", 0x8400, "vin_5vs", },
+	{ "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", },
+	{ "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", },
 	{ }
 };
 
-- 
2.9.0.rc2.8.ga28705d

[PATCH 3/3] regulator: qcom_spmi: Add support for get_mode/set_mode on switches

[Stephen Boyd]

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 43f8f20b82e9..16c5f84e06a7 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1085,6 +1085,8 @@ static struct regulator_ops spmi_vs_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 	.set_over_current_protection = spmi_regulator_vs_ocp,
+	.set_mode		= spmi_regulator_common_set_mode,
+	.get_mode		= spmi_regulator_common_get_mode,
 };
 
 static struct regulator_ops spmi_boost_ops = {
-- 
2.9.0.rc2.8.ga28705d

[PATCH 3/3] regulator: qcom_spmi: Add support for get_mode/set_mode on switches

[Stephen Boyd]

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 43f8f20b82e9..16c5f84e06a7 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1085,6 +1085,8 @@ static struct regulator_ops spmi_vs_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 	.set_over_current_protection = spmi_regulator_vs_ocp,
+	.set_mode		= spmi_regulator_common_set_mode,
+	.get_mode		= spmi_regulator_common_get_mode,
 };
 
 static struct regulator_ops spmi_boost_ops = {
-- 
2.9.0.rc2.8.ga28705d

Applied "regulator: qcom_spmi: Add support for get_mode/set_mode on switches" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for get_mode/set_mode on switches

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 919163f6362ac23138d31fc8befdd52e5d7e488d Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:13 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for get_mode/set_mode on
 switches

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 43f8f20b82e9..16c5f84e06a7 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1085,6 +1085,8 @@ static struct regulator_ops spmi_vs_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 	.set_over_current_protection = spmi_regulator_vs_ocp,
+	.set_mode		= spmi_regulator_common_set_mode,
+	.get_mode		= spmi_regulator_common_get_mode,
 };
 
 static struct regulator_ops spmi_boost_ops = {
-- 
2.8.1

Applied "regulator: qcom_spmi: Add support for get_mode/set_mode on switches" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for get_mode/set_mode on switches

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 919163f6362ac23138d31fc8befdd52e5d7e488d Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:13 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for get_mode/set_mode on
 switches

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 43f8f20b82e9..16c5f84e06a7 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1085,6 +1085,8 @@ static struct regulator_ops spmi_vs_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 	.set_over_current_protection = spmi_regulator_vs_ocp,
+	.set_mode		= spmi_regulator_common_set_mode,
+	.get_mode		= spmi_regulator_common_get_mode,
 };
 
 static struct regulator_ops spmi_boost_ops = {
-- 
2.8.1

Applied "regulator: qcom_spmi: Add support for get_mode/set_mode on switches" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for get_mode/set_mode on switches

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 919163f6362ac23138d31fc8befdd52e5d7e488d Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:13 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for get_mode/set_mode on
 switches

The voltage switches support mode switching, so add support for
these ops to those types of regulators.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/qcom_spmi-regulator.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 43f8f20b82e9..16c5f84e06a7 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1085,6 +1085,8 @@ static struct regulator_ops spmi_vs_ops = {
 	.set_pull_down		= spmi_regulator_common_set_pull_down,
 	.set_soft_start		= spmi_regulator_common_set_soft_start,
 	.set_over_current_protection = spmi_regulator_vs_ocp,
+	.set_mode		= spmi_regulator_common_set_mode,
+	.get_mode		= spmi_regulator_common_get_mode,
 };
 
 static struct regulator_ops spmi_boost_ops = {
-- 
2.8.1

Applied "regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 93bfe79b03365f410aa91caf04263173c008ecdf Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:12 -0700
Subject: [PATCH] regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 2 +-
 drivers/regulator/qcom_spmi-regulator.c                             | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 3e827bb9a56d..0fa3b0fac129 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -115,7 +115,7 @@ pm8916:
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	5vs1, 5vs2
 
 pm8994:
 	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fe09407b150b..43f8f20b82e9 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1524,8 +1524,8 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
 	{ "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
 	{ "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
-	{ "mvs1", 0x8300, "vin_5vs", },
-	{ "mvs2", 0x8400, "vin_5vs", },
+	{ "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", },
+	{ "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", },
 	{ }
 };
 
-- 
2.8.1

Applied "regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 93bfe79b03365f410aa91caf04263173c008ecdf Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:12 -0700
Subject: [PATCH] regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 2 +-
 drivers/regulator/qcom_spmi-regulator.c                             | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 3e827bb9a56d..0fa3b0fac129 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -115,7 +115,7 @@ pm8916:
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	5vs1, 5vs2
 
 pm8994:
 	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fe09407b150b..43f8f20b82e9 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1524,8 +1524,8 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
 	{ "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
 	{ "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
-	{ "mvs1", 0x8300, "vin_5vs", },
-	{ "mvs2", 0x8400, "vin_5vs", },
+	{ "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", },
+	{ "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", },
 	{ }
 };
 
-- 
2.8.1

Applied "regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 93bfe79b03365f410aa91caf04263173c008ecdf Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:12 -0700
Subject: [PATCH] regulator: qcom_spmi: Update mvs1/mvs2 switches on pm8941

The mvs1 and mvs2 switches are actually called 5vs1 and 5vs2 on
some datasheets. Let's rename them to match the datasheets and
also match the RPM based regulator driver which calls these by
their 5vs names (see qcom_smd-regulator.c). There aren't any
users of these regulators so far, so there aren't any concerns of
DT ABI breakage here. While we're here making updates to the
switches, also mandate usage of the OCP irq for these switches
too.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 2 +-
 drivers/regulator/qcom_spmi-regulator.c                             | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 3e827bb9a56d..0fa3b0fac129 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -115,7 +115,7 @@ pm8916:
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	mvs1, mvs2
+	5vs1, 5vs2
 
 pm8994:
 	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index fe09407b150b..43f8f20b82e9 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1524,8 +1524,8 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
 	{ "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
 	{ "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
-	{ "mvs1", 0x8300, "vin_5vs", },
-	{ "mvs2", 0x8400, "vin_5vs", },
+	{ "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", },
+	{ "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", },
 	{ }
 };
 
-- 
2.8.1

Applied "regulator: qcom_spmi: Add support for S4 supply on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for S4 supply on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From c333dfe8dba7d3e47e97e1cee3c38123e19ae73c Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:11 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for S4 supply on pm8941

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++--
 drivers/regulator/qcom_spmi-regulator.c                             | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 46c6f3ed1a1c..3e827bb9a56d 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -113,8 +113,8 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
 	mvs1, mvs2
 
 pm8994:
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 84cce21e98cd..fe09407b150b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1496,6 +1496,7 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "s1", 0x1400, "vdd_s1", },
 	{ "s2", 0x1700, "vdd_s2", },
 	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0xa000, },
 	{ "l1", 0x4000, "vdd_l1_l3", },
 	{ "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
 	{ "l3", 0x4200, "vdd_l1_l3", },
-- 
2.8.1

Applied "regulator: qcom_spmi: Add support for S4 supply on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for S4 supply on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From c333dfe8dba7d3e47e97e1cee3c38123e19ae73c Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:11 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for S4 supply on pm8941

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++--
 drivers/regulator/qcom_spmi-regulator.c                             | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 46c6f3ed1a1c..3e827bb9a56d 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -113,8 +113,8 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
 	mvs1, mvs2
 
 pm8994:
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 84cce21e98cd..fe09407b150b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1496,6 +1496,7 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "s1", 0x1400, "vdd_s1", },
 	{ "s2", 0x1700, "vdd_s2", },
 	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0xa000, },
 	{ "l1", 0x4000, "vdd_l1_l3", },
 	{ "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
 	{ "l3", 0x4200, "vdd_l1_l3", },
-- 
2.8.1

Applied "regulator: qcom_spmi: Add support for S4 supply on pm8941" to the regulator tree

[Mark Brown]

The patch

   regulator: qcom_spmi: Add support for S4 supply on pm8941

has been applied to the regulator tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From c333dfe8dba7d3e47e97e1cee3c38123e19ae73c Mon Sep 17 00:00:00 2001
From: Stephen Boyd <stephen.boyd@linaro.org>
Date: Sat, 25 Jun 2016 22:52:11 -0700
Subject: [PATCH] regulator: qcom_spmi: Add support for S4 supply on pm8941

The S4 supply is sometimes called the boost regulator because it
outputs 5V. Typically it's connected to the 5vs1 and 5vs2
switches for use in USB OTG and HDMI applications. Add support
for this regulator which was mistakenly left out from the initial
submission of this driver.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: e92a4047419c ("regulator: Add QCOM SPMI regulator driver")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 4 ++--
 drivers/regulator/qcom_spmi-regulator.c                             | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 46c6f3ed1a1c..3e827bb9a56d 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -113,8 +113,8 @@ pm8916:
 	l14, l15, l16, l17, l18
 
 pm8941:
-	s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
-	l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
 	mvs1, mvs2
 
 pm8994:
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 84cce21e98cd..fe09407b150b 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -1496,6 +1496,7 @@ static const struct spmi_regulator_data pm8941_regulators[] = {
 	{ "s1", 0x1400, "vdd_s1", },
 	{ "s2", 0x1700, "vdd_s2", },
 	{ "s3", 0x1a00, "vdd_s3", },
+	{ "s4", 0xa000, },
 	{ "l1", 0x4000, "vdd_l1_l3", },
 	{ "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
 	{ "l3", 0x4200, "vdd_l1_l3", },
-- 
2.8.1