[rtc-linux] [PATCH v3 0/2] AMLogic Meson SoC RTC driver

[rtc-linux] [PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Thanks to Kevin Hilmand and Neil Armstrong for reviewing the driver.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks@codethink.co.uk>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Thanks to Kevin Hilmand and Neil Armstrong for reviewing the driver.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Thanks to Kevin Hilmand and Neil Armstrong for reviewing the driver.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks@codethink.co.uk>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

[rtc-linux] [PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks@codethink.co.uk>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 0/2] AMLogic Meson SoC RTC driver

[Ben Dooks]

This series adds support for the on SoC RTC driver on the
AMLogic Meson devices. The device-tree updates are not included
as they depend on the reset-controller support in -next.

The series does not have any build dependencies, but does require
the reset controller and device-tree entries for the relevant boards
and has been tested on the ODroid-C1 board.

Changes since V1:
  <1467039135-26588-1-git-send-email-ben.dooks@codethink.co.uk>

 - Fixed checkpatch and sparse errors
 - Fixed minor locking bug when writing static-control register
 - Updated the code ordering in the rtc-meson.c driver
 - Fixed alphanumeric ordering in on-cpu rtc block
 - Added Rob Hering's ack for the DT binding documentation
 - Added better description to the RTC driver header.

Ben Dooks (2):
  rtc: support for amlogic meson rtc
  meson-rtc: add device-tree binding

 .../devicetree/bindings/rtc/rtc-amlogic.txt        |  21 ++
 drivers/rtc/Kconfig                                |   9 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-meson.c                            | 349 +++++++++++++++++++++
 6 files changed, 392 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
 create mode 100644 drivers/rtc/rtc-meson.c

-- 
2.8.1

[rtc-linux] [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

Add support for the AMLogic meson8b/meson6 RTC block.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
V3..V1:
 - Fixed alpha-ordering in Kconfig
 - Fixed checkpatch errors
 - Added basic driver information
 - Re-organised static-register access functions above rtc driver layer

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
 drivers/rtc/Kconfig     |   9 ++
 drivers/rtc/Makefile    |   1 +
 drivers/rtc/rtc-meson.c | 349 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 359 insertions(+)
 create mode 100644 drivers/rtc/rtc-meson.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 18639e0..6f4097e 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1181,6 +1181,15 @@ config RTC_DRV_ASM9260
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-asm9260.
 
+config RTC_DRV_MESON
+	tristate "AMLogic Meson Real Time Clock"
+	depends on ARCH_MESON || COMPILE_TEST
+	help
+	   Support for AMLogic Meson RTC block.
+
+	   This driver can also be built as a module, if so, the module
+	   will be called "rtc-meson".
+
 config RTC_DRV_DAVINCI
 	tristate "TI DaVinci RTC"
 	depends on ARCH_DAVINCI_DM365 || COMPILE_TEST
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index ea28337..0b4f106 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -92,6 +92,7 @@ obj-$(CONFIG_RTC_DRV_MAX8997)	+= rtc-max8997.o
 obj-$(CONFIG_RTC_DRV_MAX8998)	+= rtc-max8998.o
 obj-$(CONFIG_RTC_DRV_MC13XXX)	+= rtc-mc13xxx.o
 obj-$(CONFIG_RTC_DRV_MCP795)	+= rtc-mcp795.o
+obj-$(CONFIG_RTC_DRV_MESON)	+= rtc-meson.o
 obj-$(CONFIG_RTC_DRV_MOXART)	+= rtc-moxart.o
 obj-$(CONFIG_RTC_DRV_MPC5121)	+= rtc-mpc5121.o
 obj-$(CONFIG_RTC_DRV_VRTC)	+= rtc-mrst.o
diff --git a/drivers/rtc/rtc-meson.c b/drivers/rtc/rtc-meson.c
new file mode 100644
index 0000000..b40b0c9
--- /dev/null
+++ b/drivers/rtc/rtc-meson.c
@@ -0,0 +1,349 @@
+/* drivers/rtc/rtc-meson.c
+ *
+ * RTC driver for the interal RTC block in the AMlogic SoCs.
+ *
+ * The RTC is split in to two parts, the AHB front end and a simple serial
+ * connection to the actual registers. This driver manages both parts.
+ *
+ * Copyright (c) 2015 Codethink Ltd
+ *	 Ben Dooks <ben.dooks@codethink.co.uk>
+ * Based on origin by Carlo Caione <carlo@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
+#include <linux/rtc.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+/* registers accessed from cpu bus */
+#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
+
+#define LINE_SDI		(1 << 2)
+#define LINE_SEN		(1 << 1)
+#define LINE_SCLK		(1 << 0)
+
+#define RTCREG0_START_SER	BIT(17)
+#define RTCREG0_WAIT_SER	BIT(22)
+#define RTC_REG0_DATA(__data)	((__data) << 24)
+
+#define RTCREG1_READY		BIT(1)
+
+/* rtc registers accessed via rtc-serial interface */
+#define RTC_COUNTER		(0)
+#define RTC_SEC_ADJ		(2)
+
+#define RTC_ADDR_BITS		(3)	/* number of address bits to send */
+#define RTC_DATA_BITS		(32)	/* number of data bits to tx/rx */
+
+#define MESON_STATIC_BIAS_CUR	(0x5 << 1)
+#define MESON_STATIC_VOLTAGE	(0x3 << 11)
+#define MESON_STATIC_DEFAULT    (MESON_STATIC_BIAS_CUR | MESON_STATIC_VOLTAGE)
+
+struct meson_rtc {
+	struct rtc_device	*rtc;	/* rtc device we created */
+	struct device		*dev;	/* device we bound from */
+	struct reset_control	*reset;	/* reset source */
+	struct mutex		lock;	/* rtc lock */
+	void __iomem		*regs;	/* rtc register access */
+};
+
+/* RTC front-end serialiser controls */
+
+static void meson_rtc_setline(struct meson_rtc *rtc,
+			      unsigned int bit, unsigned int to)
+{
+	u32 reg0;
+
+	reg0 = readl(rtc->regs + RTC_REG(0));
+	if (to)
+		reg0 |= bit;
+	else
+		reg0 &= ~bit;
+	writel(reg0, rtc->regs + RTC_REG(0));
+}
+
+static void meson_rtc_sclk_pulse(struct meson_rtc *rtc)
+{
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 0);
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 1);
+}
+
+static void meson_rtc_send_bit(struct meson_rtc *rtc, unsigned int bit)
+{
+	meson_rtc_setline(rtc, LINE_SDI, bit ? 1 : 0);
+	meson_rtc_sclk_pulse(rtc);
+}
+
+static void meson_rtc_send_bits(struct meson_rtc *rtc,
+				u32 data, unsigned int nr)
+{
+	u32 bit = 1 << (nr - 1);
+
+	while (bit) {
+		meson_rtc_send_bit(rtc, data & bit);
+		bit >>= 1;
+	}
+}
+
+static void meson_rtc_set_dir(struct meson_rtc *rtc, u32 mode)
+{
+	meson_rtc_setline(rtc, LINE_SEN, 0);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+	meson_rtc_send_bit(rtc, mode);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+}
+
+static u32 meson_rtc_read_sdo(struct meson_rtc *rtc)
+{
+	return readl(rtc->regs + RTC_REG(1)) & BIT(0);
+}
+
+static u32 meson_rtc_get_data(struct meson_rtc *rtc)
+{
+	u32 val = 0;
+	int bit;
+
+	for (bit = 0; bit < RTC_DATA_BITS; bit++) {
+		meson_rtc_sclk_pulse(rtc);
+		val <<= 1;
+		val |= meson_rtc_read_sdo(rtc);
+	}
+
+	return val;
+}
+
+static int meson_rtc_wait_bus(struct meson_rtc *rtc, unsigned int timeout_ms)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
+	u32 val;
+
+	while (time_before(jiffies, timeout)) {
+		val = readl(rtc->regs + RTC_REG(1));
+		if (val & RTCREG1_READY)
+			return 1;
+
+		dev_dbg(rtc->dev, "%s: reg0=%08x reg1=%08x\n",
+			__func__, readl(rtc->regs + RTC_REG(0)), val);
+		msleep(10);
+	}
+
+	return 0;
+}
+
+static int meson_rtc_get_bus(struct meson_rtc *rtc)
+{
+	int ret, retries = 3;
+	u32 val;
+
+	/* prepare bus for transfers, set all lines low */
+	val = readl(rtc->regs + RTC_REG(0));
+	val &= ~(LINE_SDI | LINE_SEN | LINE_SCLK);
+	writel(val, rtc->regs + RTC_REG(0));
+
+	while (retries) {
+		if (meson_rtc_wait_bus(rtc, 300))
+			return 0;
+
+		dev_warn(rtc->dev, "failed to get bus, re-setting\n");
+
+		retries--;
+		ret = reset_control_reset(rtc->reset);
+		if (ret)
+			return ret;
+	}
+
+	dev_err(rtc->dev, "%s: bus is not ready\n", __func__);
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_read(struct meson_rtc *rtc, unsigned int reg, u32 *data)
+{
+	int ret;
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 0);
+	*data = meson_rtc_get_data(rtc);
+
+	return 0;
+}
+
+static int meson_rtc_write(struct meson_rtc *rtc, unsigned int reg, u32 data)
+{
+	int ret;
+
+	dev_dbg(rtc->dev, "%s: reg %d val %08x)\n", __func__, reg, data);
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, data, RTC_DATA_BITS);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 1);
+
+	return 0;
+}
+
+static int meson_rtc_wait_serialiser(struct meson_rtc *rtc)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+	while (time_before(jiffies, timeout)) {
+		if (!(readl(rtc->regs + RTC_REG(0)) & RTCREG0_WAIT_SER))
+			return 0;
+		msleep(10);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_write_static(struct meson_rtc *rtc, u32 data)
+{
+	u32 tmp;
+	int ret = 0;
+
+	mutex_lock(&rtc->lock);
+
+	writel(data >> 8, rtc->regs + RTC_REG(4));
+
+	tmp = readl(rtc->regs + RTC_REG(0));
+	tmp &= ~RTC_REG0_DATA(0xff);
+	tmp |= RTC_REG0_DATA(data);
+	tmp |= RTCREG0_START_SER;
+	writel(tmp, rtc->regs + RTC_REG(0));
+
+	if (meson_rtc_wait_serialiser(rtc))
+		ret = -ETIMEDOUT;
+
+	dev_dbg(rtc->dev, "%s: ret=%d, rtc_reg0 = %08x\n",
+		__func__, ret, readl(rtc->regs + RTC_REG(0)));
+	mutex_unlock(&rtc->lock);
+
+	return ret;
+}
+
+/* RTC interface layer functions */
+
+static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	int ret;
+	u32 time;
+
+	mutex_lock(&rtc->lock);
+
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
+	if (!ret) {
+		rtc_time_to_tm(time, tm);
+		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
+	}
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time;
+	int ret;
+
+	mutex_lock(&rtc->lock);
+
+	rtc_tm_to_time(tm, &time);
+	ret = meson_rtc_write(rtc, RTC_COUNTER, time);
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static const struct rtc_class_ops meson_rtc_ops = {
+	.read_time	= meson_rtc_gettime,
+	.set_time	= meson_rtc_settime,
+};
+
+static int meson_rtc_probe(struct platform_device *pdev)
+{
+	struct meson_rtc *rtc;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	u32 tm;
+	int ret;
+
+	rtc = devm_kzalloc(dev, sizeof(struct meson_rtc), GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	rtc->regs = devm_ioremap_resource(dev, res);
+	rtc->dev = dev;
+
+	if (IS_ERR(rtc->regs))
+		return PTR_ERR(rtc->regs);
+
+	mutex_init(&rtc->lock);
+	platform_set_drvdata(pdev, rtc);
+
+	ret = meson_rtc_write_static(rtc, MESON_STATIC_DEFAULT);
+	if (ret) {
+		dev_err(dev, "failed to set static values\n");
+		return ret;
+	}
+
+	rtc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(rtc->reset))
+		dev_warn(dev, "no reset available, rtc may not work\n");
+
+	/* check if we can read RTC counter, if not then the RTC is probably
+	 * not functional. If it isn't probably best to not bind.
+	 */
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &tm);
+	if (ret) {
+		dev_err(dev, "cannot read RTC counter, RTC not functional\n");
+		return ret;
+	}
+
+	rtc->rtc = devm_rtc_device_register(dev, "meson",
+					    &meson_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc->rtc))
+		return PTR_ERR(rtc->rtc);
+
+	return 0;
+}
+
+static const struct of_device_id meson_rtc_dt_match[] = {
+	{ .compatible = "amlogic,meson6-rtc", },
+	{ .compatible = "amlogic,meson8-rtc", },
+	{ .compatible = "amlogic,meson8b-rtc", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, meson_rtc_dt_match);
+
+static struct platform_driver meson_rtc_driver = {
+	.probe		= meson_rtc_probe,
+	.driver		= {
+		.name	= "meson-rtc",
+		.of_match_table	= of_match_ptr(meson_rtc_dt_match),
+	},
+};
+module_platform_driver(meson_rtc_driver);
+
+MODULE_DESCRIPTION("AMLogic MESON RTC Driver");
+MODULE_AUTHOR("Ben Dooks <ben.doosk@codethink.co.uk>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:meson-rtc");
-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

Add support for the AMLogic meson8b/meson6 RTC block.

Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
---
V3..V1:
 - Fixed alpha-ordering in Kconfig
 - Fixed checkpatch errors
 - Added basic driver information
 - Re-organised static-register access functions above rtc driver layer

Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
---
 drivers/rtc/Kconfig     |   9 ++
 drivers/rtc/Makefile    |   1 +
 drivers/rtc/rtc-meson.c | 349 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 359 insertions(+)
 create mode 100644 drivers/rtc/rtc-meson.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 18639e0..6f4097e 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1181,6 +1181,15 @@ config RTC_DRV_ASM9260
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-asm9260.
 
+config RTC_DRV_MESON
+	tristate "AMLogic Meson Real Time Clock"
+	depends on ARCH_MESON || COMPILE_TEST
+	help
+	   Support for AMLogic Meson RTC block.
+
+	   This driver can also be built as a module, if so, the module
+	   will be called "rtc-meson".
+
 config RTC_DRV_DAVINCI
 	tristate "TI DaVinci RTC"
 	depends on ARCH_DAVINCI_DM365 || COMPILE_TEST
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index ea28337..0b4f106 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -92,6 +92,7 @@ obj-$(CONFIG_RTC_DRV_MAX8997)	+= rtc-max8997.o
 obj-$(CONFIG_RTC_DRV_MAX8998)	+= rtc-max8998.o
 obj-$(CONFIG_RTC_DRV_MC13XXX)	+= rtc-mc13xxx.o
 obj-$(CONFIG_RTC_DRV_MCP795)	+= rtc-mcp795.o
+obj-$(CONFIG_RTC_DRV_MESON)	+= rtc-meson.o
 obj-$(CONFIG_RTC_DRV_MOXART)	+= rtc-moxart.o
 obj-$(CONFIG_RTC_DRV_MPC5121)	+= rtc-mpc5121.o
 obj-$(CONFIG_RTC_DRV_VRTC)	+= rtc-mrst.o
diff --git a/drivers/rtc/rtc-meson.c b/drivers/rtc/rtc-meson.c
new file mode 100644
index 0000000..b40b0c9
--- /dev/null
+++ b/drivers/rtc/rtc-meson.c
@@ -0,0 +1,349 @@
+/* drivers/rtc/rtc-meson.c
+ *
+ * RTC driver for the interal RTC block in the AMlogic SoCs.
+ *
+ * The RTC is split in to two parts, the AHB front end and a simple serial
+ * connection to the actual registers. This driver manages both parts.
+ *
+ * Copyright (c) 2015 Codethink Ltd
+ *	 Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
+ * Based on origin by Carlo Caione <carlo-6IF/jdPJHihWk0Htik3J/w@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
+#include <linux/rtc.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+/* registers accessed from cpu bus */
+#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
+
+#define LINE_SDI		(1 << 2)
+#define LINE_SEN		(1 << 1)
+#define LINE_SCLK		(1 << 0)
+
+#define RTCREG0_START_SER	BIT(17)
+#define RTCREG0_WAIT_SER	BIT(22)
+#define RTC_REG0_DATA(__data)	((__data) << 24)
+
+#define RTCREG1_READY		BIT(1)
+
+/* rtc registers accessed via rtc-serial interface */
+#define RTC_COUNTER		(0)
+#define RTC_SEC_ADJ		(2)
+
+#define RTC_ADDR_BITS		(3)	/* number of address bits to send */
+#define RTC_DATA_BITS		(32)	/* number of data bits to tx/rx */
+
+#define MESON_STATIC_BIAS_CUR	(0x5 << 1)
+#define MESON_STATIC_VOLTAGE	(0x3 << 11)
+#define MESON_STATIC_DEFAULT    (MESON_STATIC_BIAS_CUR | MESON_STATIC_VOLTAGE)
+
+struct meson_rtc {
+	struct rtc_device	*rtc;	/* rtc device we created */
+	struct device		*dev;	/* device we bound from */
+	struct reset_control	*reset;	/* reset source */
+	struct mutex		lock;	/* rtc lock */
+	void __iomem		*regs;	/* rtc register access */
+};
+
+/* RTC front-end serialiser controls */
+
+static void meson_rtc_setline(struct meson_rtc *rtc,
+			      unsigned int bit, unsigned int to)
+{
+	u32 reg0;
+
+	reg0 = readl(rtc->regs + RTC_REG(0));
+	if (to)
+		reg0 |= bit;
+	else
+		reg0 &= ~bit;
+	writel(reg0, rtc->regs + RTC_REG(0));
+}
+
+static void meson_rtc_sclk_pulse(struct meson_rtc *rtc)
+{
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 0);
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 1);
+}
+
+static void meson_rtc_send_bit(struct meson_rtc *rtc, unsigned int bit)
+{
+	meson_rtc_setline(rtc, LINE_SDI, bit ? 1 : 0);
+	meson_rtc_sclk_pulse(rtc);
+}
+
+static void meson_rtc_send_bits(struct meson_rtc *rtc,
+				u32 data, unsigned int nr)
+{
+	u32 bit = 1 << (nr - 1);
+
+	while (bit) {
+		meson_rtc_send_bit(rtc, data & bit);
+		bit >>= 1;
+	}
+}
+
+static void meson_rtc_set_dir(struct meson_rtc *rtc, u32 mode)
+{
+	meson_rtc_setline(rtc, LINE_SEN, 0);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+	meson_rtc_send_bit(rtc, mode);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+}
+
+static u32 meson_rtc_read_sdo(struct meson_rtc *rtc)
+{
+	return readl(rtc->regs + RTC_REG(1)) & BIT(0);
+}
+
+static u32 meson_rtc_get_data(struct meson_rtc *rtc)
+{
+	u32 val = 0;
+	int bit;
+
+	for (bit = 0; bit < RTC_DATA_BITS; bit++) {
+		meson_rtc_sclk_pulse(rtc);
+		val <<= 1;
+		val |= meson_rtc_read_sdo(rtc);
+	}
+
+	return val;
+}
+
+static int meson_rtc_wait_bus(struct meson_rtc *rtc, unsigned int timeout_ms)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
+	u32 val;
+
+	while (time_before(jiffies, timeout)) {
+		val = readl(rtc->regs + RTC_REG(1));
+		if (val & RTCREG1_READY)
+			return 1;
+
+		dev_dbg(rtc->dev, "%s: reg0=%08x reg1=%08x\n",
+			__func__, readl(rtc->regs + RTC_REG(0)), val);
+		msleep(10);
+	}
+
+	return 0;
+}
+
+static int meson_rtc_get_bus(struct meson_rtc *rtc)
+{
+	int ret, retries = 3;
+	u32 val;
+
+	/* prepare bus for transfers, set all lines low */
+	val = readl(rtc->regs + RTC_REG(0));
+	val &= ~(LINE_SDI | LINE_SEN | LINE_SCLK);
+	writel(val, rtc->regs + RTC_REG(0));
+
+	while (retries) {
+		if (meson_rtc_wait_bus(rtc, 300))
+			return 0;
+
+		dev_warn(rtc->dev, "failed to get bus, re-setting\n");
+
+		retries--;
+		ret = reset_control_reset(rtc->reset);
+		if (ret)
+			return ret;
+	}
+
+	dev_err(rtc->dev, "%s: bus is not ready\n", __func__);
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_read(struct meson_rtc *rtc, unsigned int reg, u32 *data)
+{
+	int ret;
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 0);
+	*data = meson_rtc_get_data(rtc);
+
+	return 0;
+}
+
+static int meson_rtc_write(struct meson_rtc *rtc, unsigned int reg, u32 data)
+{
+	int ret;
+
+	dev_dbg(rtc->dev, "%s: reg %d val %08x)\n", __func__, reg, data);
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, data, RTC_DATA_BITS);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 1);
+
+	return 0;
+}
+
+static int meson_rtc_wait_serialiser(struct meson_rtc *rtc)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+	while (time_before(jiffies, timeout)) {
+		if (!(readl(rtc->regs + RTC_REG(0)) & RTCREG0_WAIT_SER))
+			return 0;
+		msleep(10);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_write_static(struct meson_rtc *rtc, u32 data)
+{
+	u32 tmp;
+	int ret = 0;
+
+	mutex_lock(&rtc->lock);
+
+	writel(data >> 8, rtc->regs + RTC_REG(4));
+
+	tmp = readl(rtc->regs + RTC_REG(0));
+	tmp &= ~RTC_REG0_DATA(0xff);
+	tmp |= RTC_REG0_DATA(data);
+	tmp |= RTCREG0_START_SER;
+	writel(tmp, rtc->regs + RTC_REG(0));
+
+	if (meson_rtc_wait_serialiser(rtc))
+		ret = -ETIMEDOUT;
+
+	dev_dbg(rtc->dev, "%s: ret=%d, rtc_reg0 = %08x\n",
+		__func__, ret, readl(rtc->regs + RTC_REG(0)));
+	mutex_unlock(&rtc->lock);
+
+	return ret;
+}
+
+/* RTC interface layer functions */
+
+static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	int ret;
+	u32 time;
+
+	mutex_lock(&rtc->lock);
+
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
+	if (!ret) {
+		rtc_time_to_tm(time, tm);
+		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
+	}
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time;
+	int ret;
+
+	mutex_lock(&rtc->lock);
+
+	rtc_tm_to_time(tm, &time);
+	ret = meson_rtc_write(rtc, RTC_COUNTER, time);
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static const struct rtc_class_ops meson_rtc_ops = {
+	.read_time	= meson_rtc_gettime,
+	.set_time	= meson_rtc_settime,
+};
+
+static int meson_rtc_probe(struct platform_device *pdev)
+{
+	struct meson_rtc *rtc;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	u32 tm;
+	int ret;
+
+	rtc = devm_kzalloc(dev, sizeof(struct meson_rtc), GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	rtc->regs = devm_ioremap_resource(dev, res);
+	rtc->dev = dev;
+
+	if (IS_ERR(rtc->regs))
+		return PTR_ERR(rtc->regs);
+
+	mutex_init(&rtc->lock);
+	platform_set_drvdata(pdev, rtc);
+
+	ret = meson_rtc_write_static(rtc, MESON_STATIC_DEFAULT);
+	if (ret) {
+		dev_err(dev, "failed to set static values\n");
+		return ret;
+	}
+
+	rtc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(rtc->reset))
+		dev_warn(dev, "no reset available, rtc may not work\n");
+
+	/* check if we can read RTC counter, if not then the RTC is probably
+	 * not functional. If it isn't probably best to not bind.
+	 */
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &tm);
+	if (ret) {
+		dev_err(dev, "cannot read RTC counter, RTC not functional\n");
+		return ret;
+	}
+
+	rtc->rtc = devm_rtc_device_register(dev, "meson",
+					    &meson_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc->rtc))
+		return PTR_ERR(rtc->rtc);
+
+	return 0;
+}
+
+static const struct of_device_id meson_rtc_dt_match[] = {
+	{ .compatible = "amlogic,meson6-rtc", },
+	{ .compatible = "amlogic,meson8-rtc", },
+	{ .compatible = "amlogic,meson8b-rtc", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, meson_rtc_dt_match);
+
+static struct platform_driver meson_rtc_driver = {
+	.probe		= meson_rtc_probe,
+	.driver		= {
+		.name	= "meson-rtc",
+		.of_match_table	= of_match_ptr(meson_rtc_dt_match),
+	},
+};
+module_platform_driver(meson_rtc_driver);
+
+MODULE_DESCRIPTION("AMLogic MESON RTC Driver");
+MODULE_AUTHOR("Ben Dooks <ben.doosk-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:meson-rtc");
-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

Add support for the AMLogic meson8b/meson6 RTC block.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
V3..V1:
 - Fixed alpha-ordering in Kconfig
 - Fixed checkpatch errors
 - Added basic driver information
 - Re-organised static-register access functions above rtc driver layer

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
---
 drivers/rtc/Kconfig     |   9 ++
 drivers/rtc/Makefile    |   1 +
 drivers/rtc/rtc-meson.c | 349 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 359 insertions(+)
 create mode 100644 drivers/rtc/rtc-meson.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 18639e0..6f4097e 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1181,6 +1181,15 @@ config RTC_DRV_ASM9260
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-asm9260.
 
+config RTC_DRV_MESON
+	tristate "AMLogic Meson Real Time Clock"
+	depends on ARCH_MESON || COMPILE_TEST
+	help
+	   Support for AMLogic Meson RTC block.
+
+	   This driver can also be built as a module, if so, the module
+	   will be called "rtc-meson".
+
 config RTC_DRV_DAVINCI
 	tristate "TI DaVinci RTC"
 	depends on ARCH_DAVINCI_DM365 || COMPILE_TEST
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index ea28337..0b4f106 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -92,6 +92,7 @@ obj-$(CONFIG_RTC_DRV_MAX8997)	+= rtc-max8997.o
 obj-$(CONFIG_RTC_DRV_MAX8998)	+= rtc-max8998.o
 obj-$(CONFIG_RTC_DRV_MC13XXX)	+= rtc-mc13xxx.o
 obj-$(CONFIG_RTC_DRV_MCP795)	+= rtc-mcp795.o
+obj-$(CONFIG_RTC_DRV_MESON)	+= rtc-meson.o
 obj-$(CONFIG_RTC_DRV_MOXART)	+= rtc-moxart.o
 obj-$(CONFIG_RTC_DRV_MPC5121)	+= rtc-mpc5121.o
 obj-$(CONFIG_RTC_DRV_VRTC)	+= rtc-mrst.o
diff --git a/drivers/rtc/rtc-meson.c b/drivers/rtc/rtc-meson.c
new file mode 100644
index 0000000..b40b0c9
--- /dev/null
+++ b/drivers/rtc/rtc-meson.c
@@ -0,0 +1,349 @@
+/* drivers/rtc/rtc-meson.c
+ *
+ * RTC driver for the interal RTC block in the AMlogic SoCs.
+ *
+ * The RTC is split in to two parts, the AHB front end and a simple serial
+ * connection to the actual registers. This driver manages both parts.
+ *
+ * Copyright (c) 2015 Codethink Ltd
+ *	 Ben Dooks <ben.dooks@codethink.co.uk>
+ * Based on origin by Carlo Caione <carlo@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
+#include <linux/rtc.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+/* registers accessed from cpu bus */
+#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
+
+#define LINE_SDI		(1 << 2)
+#define LINE_SEN		(1 << 1)
+#define LINE_SCLK		(1 << 0)
+
+#define RTCREG0_START_SER	BIT(17)
+#define RTCREG0_WAIT_SER	BIT(22)
+#define RTC_REG0_DATA(__data)	((__data) << 24)
+
+#define RTCREG1_READY		BIT(1)
+
+/* rtc registers accessed via rtc-serial interface */
+#define RTC_COUNTER		(0)
+#define RTC_SEC_ADJ		(2)
+
+#define RTC_ADDR_BITS		(3)	/* number of address bits to send */
+#define RTC_DATA_BITS		(32)	/* number of data bits to tx/rx */
+
+#define MESON_STATIC_BIAS_CUR	(0x5 << 1)
+#define MESON_STATIC_VOLTAGE	(0x3 << 11)
+#define MESON_STATIC_DEFAULT    (MESON_STATIC_BIAS_CUR | MESON_STATIC_VOLTAGE)
+
+struct meson_rtc {
+	struct rtc_device	*rtc;	/* rtc device we created */
+	struct device		*dev;	/* device we bound from */
+	struct reset_control	*reset;	/* reset source */
+	struct mutex		lock;	/* rtc lock */
+	void __iomem		*regs;	/* rtc register access */
+};
+
+/* RTC front-end serialiser controls */
+
+static void meson_rtc_setline(struct meson_rtc *rtc,
+			      unsigned int bit, unsigned int to)
+{
+	u32 reg0;
+
+	reg0 = readl(rtc->regs + RTC_REG(0));
+	if (to)
+		reg0 |= bit;
+	else
+		reg0 &= ~bit;
+	writel(reg0, rtc->regs + RTC_REG(0));
+}
+
+static void meson_rtc_sclk_pulse(struct meson_rtc *rtc)
+{
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 0);
+	udelay(5);
+	meson_rtc_setline(rtc, LINE_SCLK, 1);
+}
+
+static void meson_rtc_send_bit(struct meson_rtc *rtc, unsigned int bit)
+{
+	meson_rtc_setline(rtc, LINE_SDI, bit ? 1 : 0);
+	meson_rtc_sclk_pulse(rtc);
+}
+
+static void meson_rtc_send_bits(struct meson_rtc *rtc,
+				u32 data, unsigned int nr)
+{
+	u32 bit = 1 << (nr - 1);
+
+	while (bit) {
+		meson_rtc_send_bit(rtc, data & bit);
+		bit >>= 1;
+	}
+}
+
+static void meson_rtc_set_dir(struct meson_rtc *rtc, u32 mode)
+{
+	meson_rtc_setline(rtc, LINE_SEN, 0);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+	meson_rtc_send_bit(rtc, mode);
+	meson_rtc_setline(rtc, LINE_SDI, 0);
+}
+
+static u32 meson_rtc_read_sdo(struct meson_rtc *rtc)
+{
+	return readl(rtc->regs + RTC_REG(1)) & BIT(0);
+}
+
+static u32 meson_rtc_get_data(struct meson_rtc *rtc)
+{
+	u32 val = 0;
+	int bit;
+
+	for (bit = 0; bit < RTC_DATA_BITS; bit++) {
+		meson_rtc_sclk_pulse(rtc);
+		val <<= 1;
+		val |= meson_rtc_read_sdo(rtc);
+	}
+
+	return val;
+}
+
+static int meson_rtc_wait_bus(struct meson_rtc *rtc, unsigned int timeout_ms)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(timeout_ms);
+	u32 val;
+
+	while (time_before(jiffies, timeout)) {
+		val = readl(rtc->regs + RTC_REG(1));
+		if (val & RTCREG1_READY)
+			return 1;
+
+		dev_dbg(rtc->dev, "%s: reg0=%08x reg1=%08x\n",
+			__func__, readl(rtc->regs + RTC_REG(0)), val);
+		msleep(10);
+	}
+
+	return 0;
+}
+
+static int meson_rtc_get_bus(struct meson_rtc *rtc)
+{
+	int ret, retries = 3;
+	u32 val;
+
+	/* prepare bus for transfers, set all lines low */
+	val = readl(rtc->regs + RTC_REG(0));
+	val &= ~(LINE_SDI | LINE_SEN | LINE_SCLK);
+	writel(val, rtc->regs + RTC_REG(0));
+
+	while (retries) {
+		if (meson_rtc_wait_bus(rtc, 300))
+			return 0;
+
+		dev_warn(rtc->dev, "failed to get bus, re-setting\n");
+
+		retries--;
+		ret = reset_control_reset(rtc->reset);
+		if (ret)
+			return ret;
+	}
+
+	dev_err(rtc->dev, "%s: bus is not ready\n", __func__);
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_read(struct meson_rtc *rtc, unsigned int reg, u32 *data)
+{
+	int ret;
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 0);
+	*data = meson_rtc_get_data(rtc);
+
+	return 0;
+}
+
+static int meson_rtc_write(struct meson_rtc *rtc, unsigned int reg, u32 data)
+{
+	int ret;
+
+	dev_dbg(rtc->dev, "%s: reg %d val %08x)\n", __func__, reg, data);
+
+	ret = meson_rtc_get_bus(rtc);
+	if (ret)
+		return ret;
+
+	meson_rtc_setline(rtc, LINE_SEN, 1);
+	meson_rtc_send_bits(rtc, data, RTC_DATA_BITS);
+	meson_rtc_send_bits(rtc, reg, RTC_ADDR_BITS);
+	meson_rtc_set_dir(rtc, 1);
+
+	return 0;
+}
+
+static int meson_rtc_wait_serialiser(struct meson_rtc *rtc)
+{
+	unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+	while (time_before(jiffies, timeout)) {
+		if (!(readl(rtc->regs + RTC_REG(0)) & RTCREG0_WAIT_SER))
+			return 0;
+		msleep(10);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int meson_rtc_write_static(struct meson_rtc *rtc, u32 data)
+{
+	u32 tmp;
+	int ret = 0;
+
+	mutex_lock(&rtc->lock);
+
+	writel(data >> 8, rtc->regs + RTC_REG(4));
+
+	tmp = readl(rtc->regs + RTC_REG(0));
+	tmp &= ~RTC_REG0_DATA(0xff);
+	tmp |= RTC_REG0_DATA(data);
+	tmp |= RTCREG0_START_SER;
+	writel(tmp, rtc->regs + RTC_REG(0));
+
+	if (meson_rtc_wait_serialiser(rtc))
+		ret = -ETIMEDOUT;
+
+	dev_dbg(rtc->dev, "%s: ret=%d, rtc_reg0 = %08x\n",
+		__func__, ret, readl(rtc->regs + RTC_REG(0)));
+	mutex_unlock(&rtc->lock);
+
+	return ret;
+}
+
+/* RTC interface layer functions */
+
+static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	int ret;
+	u32 time;
+
+	mutex_lock(&rtc->lock);
+
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
+	if (!ret) {
+		rtc_time_to_tm(time, tm);
+		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
+	}
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
+{
+	struct meson_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time;
+	int ret;
+
+	mutex_lock(&rtc->lock);
+
+	rtc_tm_to_time(tm, &time);
+	ret = meson_rtc_write(rtc, RTC_COUNTER, time);
+
+	mutex_unlock(&rtc->lock);
+	return ret;
+}
+
+static const struct rtc_class_ops meson_rtc_ops = {
+	.read_time	= meson_rtc_gettime,
+	.set_time	= meson_rtc_settime,
+};
+
+static int meson_rtc_probe(struct platform_device *pdev)
+{
+	struct meson_rtc *rtc;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	u32 tm;
+	int ret;
+
+	rtc = devm_kzalloc(dev, sizeof(struct meson_rtc), GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	rtc->regs = devm_ioremap_resource(dev, res);
+	rtc->dev = dev;
+
+	if (IS_ERR(rtc->regs))
+		return PTR_ERR(rtc->regs);
+
+	mutex_init(&rtc->lock);
+	platform_set_drvdata(pdev, rtc);
+
+	ret = meson_rtc_write_static(rtc, MESON_STATIC_DEFAULT);
+	if (ret) {
+		dev_err(dev, "failed to set static values\n");
+		return ret;
+	}
+
+	rtc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(rtc->reset))
+		dev_warn(dev, "no reset available, rtc may not work\n");
+
+	/* check if we can read RTC counter, if not then the RTC is probably
+	 * not functional. If it isn't probably best to not bind.
+	 */
+	ret = meson_rtc_read(rtc, RTC_COUNTER, &tm);
+	if (ret) {
+		dev_err(dev, "cannot read RTC counter, RTC not functional\n");
+		return ret;
+	}
+
+	rtc->rtc = devm_rtc_device_register(dev, "meson",
+					    &meson_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc->rtc))
+		return PTR_ERR(rtc->rtc);
+
+	return 0;
+}
+
+static const struct of_device_id meson_rtc_dt_match[] = {
+	{ .compatible = "amlogic,meson6-rtc", },
+	{ .compatible = "amlogic,meson8-rtc", },
+	{ .compatible = "amlogic,meson8b-rtc", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, meson_rtc_dt_match);
+
+static struct platform_driver meson_rtc_driver = {
+	.probe		= meson_rtc_probe,
+	.driver		= {
+		.name	= "meson-rtc",
+		.of_match_table	= of_match_ptr(meson_rtc_dt_match),
+	},
+};
+module_platform_driver(meson_rtc_driver);
+
+MODULE_DESCRIPTION("AMLogic MESON RTC Driver");
+MODULE_AUTHOR("Ben Dooks <ben.doosk@codethink.co.uk>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:meson-rtc");
-- 
2.8.1

[rtc-linux] [PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

Add documentation for the AMLogic Meson RTC.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

diff --git a/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
new file mode 100644
index 0000000..efc7672
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
@@ -0,0 +1,21 @@
+* AMlogic Meson RTC
+
+Required properties:
+- compatible: should be one of the following describing the hardware:
+	* "amlogic,meson6-rtc"
+	* "amlogic,meson8-rtc"
+	* "amlogic,meson8b-rtc"
+
+- reg: physical register space for the controller's memory mapped registers.
+
+Optional properties:
+- resets: reset controller reference to allow reset of the controller
+- interrupts: single interrupt reference if interrupt support needed
+
+Example:
+
+	rtc: rtc@c8100740 {
+		compatible = "amlogic,meson6-rtc";
+		reg = <0xc8100740 0x14>;
+		status = "disabled";
+	};
-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

Add documentation for the AMLogic Meson RTC.

Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

diff --git a/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
new file mode 100644
index 0000000..efc7672
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
@@ -0,0 +1,21 @@
+* AMlogic Meson RTC
+
+Required properties:
+- compatible: should be one of the following describing the hardware:
+	* "amlogic,meson6-rtc"
+	* "amlogic,meson8-rtc"
+	* "amlogic,meson8b-rtc"
+
+- reg: physical register space for the controller's memory mapped registers.
+
+Optional properties:
+- resets: reset controller reference to allow reset of the controller
+- interrupts: single interrupt reference if interrupt support needed
+
+Example:
+
+	rtc: rtc@c8100740 {
+		compatible = "amlogic,meson6-rtc";
+		reg = <0xc8100740 0x14>;
+		status = "disabled";
+	};
-- 
2.8.1

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

Add documentation for the AMLogic Meson RTC.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

diff --git a/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
new file mode 100644
index 0000000..efc7672
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
@@ -0,0 +1,21 @@
+* AMlogic Meson RTC
+
+Required properties:
+- compatible: should be one of the following describing the hardware:
+	* "amlogic,meson6-rtc"
+	* "amlogic,meson8-rtc"
+	* "amlogic,meson8b-rtc"
+
+- reg: physical register space for the controller's memory mapped registers.
+
+Optional properties:
+- resets: reset controller reference to allow reset of the controller
+- interrupts: single interrupt reference if interrupt support needed
+
+Example:
+
+	rtc: rtc at c8100740 {
+		compatible = "amlogic,meson6-rtc";
+		reg = <0xc8100740 0x14>;
+		status = "disabled";
+	};
-- 
2.8.1

[rtc-linux] Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Kevin Hilman]

Ben Dooks <ben.dooks@codethink.co.uk> writes:

> Add support for the AMLogic meson8b/meson6 RTC block.
>
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

Tested-by: Kevin Hilman <khilman@baylibre.com>

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Kevin Hilman]

Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org> writes:

> Add support for the AMLogic meson8b/meson6 RTC block.
>
> Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>

Tested-by: Kevin Hilman <khilman-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Kevin Hilman]

Ben Dooks <ben.dooks@codethink.co.uk> writes:

> Add support for the AMLogic meson8b/meson6 RTC block.
>
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

Tested-by: Kevin Hilman <khilman@baylibre.com>

[rtc-linux] Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

Hi,

Very few comments below

On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> +/* registers accessed from cpu bus */
> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> +
> +#define LINE_SDI		(1 << 2)
> +#define LINE_SEN		(1 << 1)
> +#define LINE_SCLK		(1 << 0)
> +

Maybe use BIT() here.

> +/* RTC interface layer functions */
> +
> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	int ret;
> +	u32 time;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> +	if (!ret) {
> +		rtc_time_to_tm(time, tm);

Can you use the 64bit version?

> +		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
> +	}
> +
> +	mutex_unlock(&rtc->lock);
> +	return ret;
> +}
> +
> +static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	unsigned long time;
> +	int ret;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	rtc_tm_to_time(tm, &time);

Ditto.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

Hi,

Very few comments below

On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> +/* registers accessed from cpu bus */
> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> +
> +#define LINE_SDI		(1 << 2)
> +#define LINE_SEN		(1 << 1)
> +#define LINE_SCLK		(1 << 0)
> +

Maybe use BIT() here.

> +/* RTC interface layer functions */
> +
> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	int ret;
> +	u32 time;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> +	if (!ret) {
> +		rtc_time_to_tm(time, tm);

Can you use the 64bit version?

> +		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
> +	}
> +
> +	mutex_unlock(&rtc->lock);
> +	return ret;
> +}
> +
> +static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	unsigned long time;
> +	int ret;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	rtc_tm_to_time(tm, &time);

Ditto.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

Hi,

Very few comments below

On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> +/* registers accessed from cpu bus */
> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> +
> +#define LINE_SDI		(1 << 2)
> +#define LINE_SEN		(1 << 1)
> +#define LINE_SCLK		(1 << 0)
> +

Maybe use BIT() here.

> +/* RTC interface layer functions */
> +
> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	int ret;
> +	u32 time;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> +	if (!ret) {
> +		rtc_time_to_tm(time, tm);

Can you use the 64bit version?

> +		dev_dbg(dev, "read time %lu\n", (unsigned long)time);
> +	}
> +
> +	mutex_unlock(&rtc->lock);
> +	return ret;
> +}
> +
> +static int meson_rtc_settime(struct device *dev, struct rtc_time *tm)
> +{
> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> +	unsigned long time;
> +	int ret;
> +
> +	mutex_lock(&rtc->lock);
> +
> +	rtc_tm_to_time(tm, &time);

Ditto.


-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

On 12/07/16 18:22, Alexandre Belloni wrote:
> Hi,
> 
> Very few comments below
> 
> On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
>> +/* registers accessed from cpu bus */
>> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
>> +
>> +#define LINE_SDI		(1 << 2)
>> +#define LINE_SEN		(1 << 1)
>> +#define LINE_SCLK		(1 << 0)
> 
> Maybe use BIT() here.

I'll sort that out later.

>> +/* RTC interface layer functions */
>> +
>> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
>> +{
>> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
>> +	int ret;
>> +	u32 time;
>> +
>> +	mutex_lock(&rtc->lock);
>> +
>> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
>> +	if (!ret) {
>> +		rtc_time_to_tm(time, tm);
> 
> Can you use the 64bit version?

What would the 64bit version gain? The hardware register is 32bit.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

On 12/07/16 18:22, Alexandre Belloni wrote:
> Hi,
> 
> Very few comments below
> 
> On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
>> +/* registers accessed from cpu bus */
>> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
>> +
>> +#define LINE_SDI		(1 << 2)
>> +#define LINE_SEN		(1 << 1)
>> +#define LINE_SCLK		(1 << 0)
> 
> Maybe use BIT() here.

I'll sort that out later.

>> +/* RTC interface layer functions */
>> +
>> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
>> +{
>> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
>> +	int ret;
>> +	u32 time;
>> +
>> +	mutex_lock(&rtc->lock);
>> +
>> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
>> +	if (!ret) {
>> +		rtc_time_to_tm(time, tm);
> 
> Can you use the 64bit version?

What would the 64bit version gain? The hardware register is 32bit.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Ben Dooks]

On 12/07/16 18:22, Alexandre Belloni wrote:
> Hi,
> 
> Very few comments below
> 
> On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
>> +/* registers accessed from cpu bus */
>> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
>> +
>> +#define LINE_SDI		(1 << 2)
>> +#define LINE_SEN		(1 << 1)
>> +#define LINE_SCLK		(1 << 0)
> 
> Maybe use BIT() here.

I'll sort that out later.

>> +/* RTC interface layer functions */
>> +
>> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
>> +{
>> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
>> +	int ret;
>> +	u32 time;
>> +
>> +	mutex_lock(&rtc->lock);
>> +
>> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
>> +	if (!ret) {
>> +		rtc_time_to_tm(time, tm);
> 
> Can you use the 64bit version?

What would the 64bit version gain? The hardware register is 32bit.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

[rtc-linux] Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

On 12/07/2016 at 18:27:12 +0100, Ben Dooks wrote :
> On 12/07/16 18:22, Alexandre Belloni wrote:
> > Hi,
> > 
> > Very few comments below
> > 
> > On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> >> +/* registers accessed from cpu bus */
> >> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> >> +
> >> +#define LINE_SDI		(1 << 2)
> >> +#define LINE_SEN		(1 << 1)
> >> +#define LINE_SCLK		(1 << 0)
> > 
> > Maybe use BIT() here.
> 
> I'll sort that out later.
> 
> >> +/* RTC interface layer functions */
> >> +
> >> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> >> +{
> >> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> >> +	int ret;
> >> +	u32 time;
> >> +
> >> +	mutex_lock(&rtc->lock);
> >> +
> >> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> >> +	if (!ret) {
> >> +		rtc_time_to_tm(time, tm);
> > 
> > Can you use the 64bit version?
> 
> What would the 64bit version gain? The hardware register is 32bit.
> 

Well, at some point, I'll remove the 32bit version:
http://lxr.free-electrons.com/source/include/linux/rtc.h#L36

-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

On 12/07/2016 at 18:27:12 +0100, Ben Dooks wrote :
> On 12/07/16 18:22, Alexandre Belloni wrote:
> > Hi,
> > 
> > Very few comments below
> > 
> > On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> >> +/* registers accessed from cpu bus */
> >> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> >> +
> >> +#define LINE_SDI		(1 << 2)
> >> +#define LINE_SEN		(1 << 1)
> >> +#define LINE_SCLK		(1 << 0)
> > 
> > Maybe use BIT() here.
> 
> I'll sort that out later.
> 
> >> +/* RTC interface layer functions */
> >> +
> >> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> >> +{
> >> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> >> +	int ret;
> >> +	u32 time;
> >> +
> >> +	mutex_lock(&rtc->lock);
> >> +
> >> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> >> +	if (!ret) {
> >> +		rtc_time_to_tm(time, tm);
> > 
> > Can you use the 64bit version?
> 
> What would the 64bit version gain? The hardware register is 32bit.
> 

Well, at some point, I'll remove the 32bit version:
http://lxr.free-electrons.com/source/include/linux/rtc.h#L36

-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 1/4] rtc: support for amlogic meson rtc

[Alexandre Belloni]

On 12/07/2016 at 18:27:12 +0100, Ben Dooks wrote :
> On 12/07/16 18:22, Alexandre Belloni wrote:
> > Hi,
> > 
> > Very few comments below
> > 
> > On 05/07/2016 at 20:48:41 +0100, Ben Dooks wrote :
> >> +/* registers accessed from cpu bus */
> >> +#define RTC_REG(x)		((x) * 4)	/* rtc registers 0-4 */
> >> +
> >> +#define LINE_SDI		(1 << 2)
> >> +#define LINE_SEN		(1 << 1)
> >> +#define LINE_SCLK		(1 << 0)
> > 
> > Maybe use BIT() here.
> 
> I'll sort that out later.
> 
> >> +/* RTC interface layer functions */
> >> +
> >> +static int meson_rtc_gettime(struct device *dev, struct rtc_time *tm)
> >> +{
> >> +	struct meson_rtc *rtc = dev_get_drvdata(dev);
> >> +	int ret;
> >> +	u32 time;
> >> +
> >> +	mutex_lock(&rtc->lock);
> >> +
> >> +	ret = meson_rtc_read(rtc, RTC_COUNTER, &time);
> >> +	if (!ret) {
> >> +		rtc_time_to_tm(time, tm);
> > 
> > Can you use the 64bit version?
> 
> What would the 64bit version gain? The hardware register is 32bit.
> 

Well, at some point, I'll remove the 32bit version:
http://lxr.free-electrons.com/source/include/linux/rtc.h#L36

-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

[rtc-linux] Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Frank Rowand]

On 07/05/16 12:48, Ben Dooks wrote:
> Add documentation for the AMLogic Meson RTC.
> 
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

Hi Ben,

I suspect you already know this since you have Rob's ack, but you need to
send bindings to

  Rob Herring <robh+dt@kernel.org>
  Mark Rutland <mark.rutland@arm.com>

-Frank

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Frank Rowand]

On 07/05/16 12:48, Ben Dooks wrote:
> Add documentation for the AMLogic Meson RTC.
> 
> Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> ---
>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

Hi Ben,

I suspect you already know this since you have Rob's ack, but you need to
send bindings to

  Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
  Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>

-Frank

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 2/4] meson-rtc: add device-tree binding

[Frank Rowand]

On 07/05/16 12:48, Ben Dooks wrote:
> Add documentation for the AMLogic Meson RTC.
> 
> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>  1 file changed, 21 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt

Hi Ben,

I suspect you already know this since you have Rob's ack, but you need to
send bindings to

  Rob Herring <robh+dt@kernel.org>
  Mark Rutland <mark.rutland@arm.com>

-Frank

[rtc-linux] Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

On 13/07/16 06:57, Frank Rowand wrote:
> On 07/05/16 12:48, Ben Dooks wrote:
>> Add documentation for the AMLogic Meson RTC.
>>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Acked-by: Rob Herring <robh@kernel.org>
>> ---
>>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>>  1 file changed, 21 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> 
> Hi Ben,
> 
> I suspect you already know this since you have Rob's ack, but you need to
> send bindings to
> 
>   Rob Herring <robh+dt@kernel.org>
>   Mark Rutland <mark.rutland@arm.com>

Sorry, missed copying the email when sending.

I hope he's seen them from being on the devicetree@vger.kernel.org
list? I've added him as an CC: on this one to check.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

On 13/07/16 06:57, Frank Rowand wrote:
> On 07/05/16 12:48, Ben Dooks wrote:
>> Add documentation for the AMLogic Meson RTC.
>>
>> Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
>> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> ---
>>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>>  1 file changed, 21 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> 
> Hi Ben,
> 
> I suspect you already know this since you have Rob's ack, but you need to
> send bindings to
> 
>   Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>   Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>

Sorry, missed copying the email when sending.

I hope he's seen them from being on the devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
list? I've added him as an CC: on this one to check.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 2/4] meson-rtc: add device-tree binding

[Ben Dooks]

On 13/07/16 06:57, Frank Rowand wrote:
> On 07/05/16 12:48, Ben Dooks wrote:
>> Add documentation for the AMLogic Meson RTC.
>>
>> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
>> Acked-by: Rob Herring <robh@kernel.org>
>> ---
>>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
>>  1 file changed, 21 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> 
> Hi Ben,
> 
> I suspect you already know this since you have Rob's ack, but you need to
> send bindings to
> 
>   Rob Herring <robh+dt@kernel.org>
>   Mark Rutland <mark.rutland@arm.com>

Sorry, missed copying the email when sending.

I hope he's seen them from being on the devicetree at vger.kernel.org
list? I've added him as an CC: on this one to check.

-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

[rtc-linux] Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Mark Rutland]

On Wed, Jul 13, 2016 at 10:09:44AM +0100, Ben Dooks wrote:
> On 13/07/16 06:57, Frank Rowand wrote:
> > On 07/05/16 12:48, Ben Dooks wrote:
> >> Add documentation for the AMLogic Meson RTC.
> >>
> >> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> >> Acked-by: Rob Herring <robh@kernel.org>
> >> ---
> >>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
> >>  1 file changed, 21 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> > 
> > Hi Ben,
> > 
> > I suspect you already know this since you have Rob's ack, but you need to
> > send bindings to
> > 
> >   Rob Herring <robh+dt@kernel.org>
> >   Mark Rutland <mark.rutland@arm.com>
> 
> Sorry, missed copying the email when sending.
> 
> I hope he's seen them from being on the devicetree@vger.kernel.org
> list? I've added him as an CC: on this one to check.

>From my perspective, having devicetree@vger.kernel.org alone is fine. I
appreciate tastes vary across maintainers, either way is fine by me. :)

You already have Rob's ack, which is sufficient, but FWIW the patch
looks fine, so feel free to add mine:

Acked-by: Mark Rutland <mark.rutland@arm.com>

Thanks,
Mark.

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Re: [PATCH v3 2/4] meson-rtc: add device-tree binding

[Mark Rutland]

On Wed, Jul 13, 2016 at 10:09:44AM +0100, Ben Dooks wrote:
> On 13/07/16 06:57, Frank Rowand wrote:
> > On 07/05/16 12:48, Ben Dooks wrote:
> >> Add documentation for the AMLogic Meson RTC.
> >>
> >> Signed-off-by: Ben Dooks <ben.dooks-4yDnlxn2s6sWdaTGBSpHTA@public.gmane.org>
> >> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> >> ---
> >>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
> >>  1 file changed, 21 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> > 
> > Hi Ben,
> > 
> > I suspect you already know this since you have Rob's ack, but you need to
> > send bindings to
> > 
> >   Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> >   Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
> 
> Sorry, missed copying the email when sending.
> 
> I hope he's seen them from being on the devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> list? I've added him as an CC: on this one to check.

>From my perspective, having devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org alone is fine. I
appreciate tastes vary across maintainers, either way is fine by me. :)

You already have Rob's ack, which is sufficient, but FWIW the patch
looks fine, so feel free to add mine:

Acked-by: Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>

Thanks,
Mark.

-- 
You received this message because you are subscribed to "rtc-linux".
Membership options at http://groups.google.com/group/rtc-linux .
Please read http://groups.google.com/group/rtc-linux/web/checklist
before submitting a driver.
--- 
You received this message because you are subscribed to the Google Groups "rtc-linux" group.
To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[PATCH v3 2/4] meson-rtc: add device-tree binding

[Mark Rutland]

On Wed, Jul 13, 2016 at 10:09:44AM +0100, Ben Dooks wrote:
> On 13/07/16 06:57, Frank Rowand wrote:
> > On 07/05/16 12:48, Ben Dooks wrote:
> >> Add documentation for the AMLogic Meson RTC.
> >>
> >> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
> >> Acked-by: Rob Herring <robh@kernel.org>
> >> ---
> >>  .../devicetree/bindings/rtc/rtc-amlogic.txt         | 21 +++++++++++++++++++++
> >>  1 file changed, 21 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/rtc/rtc-amlogic.txt
> > 
> > Hi Ben,
> > 
> > I suspect you already know this since you have Rob's ack, but you need to
> > send bindings to
> > 
> >   Rob Herring <robh+dt@kernel.org>
> >   Mark Rutland <mark.rutland@arm.com>
> 
> Sorry, missed copying the email when sending.
> 
> I hope he's seen them from being on the devicetree at vger.kernel.org
> list? I've added him as an CC: on this one to check.

>From my perspective, having devicetree at vger.kernel.org alone is fine. I
appreciate tastes vary across maintainers, either way is fine by me. :)

You already have Rob's ack, which is sufficient, but FWIW the patch
looks fine, so feel free to add mine:

Acked-by: Mark Rutland <mark.rutland@arm.com>

Thanks,
Mark.