From: Chen-Yu Tsai <wens@csie.org> To: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Subject: [PATCH 3/3] ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi Date: Fri, 28 Oct 2016 18:11:54 +0800 [thread overview] Message-ID: <20161028101154.7350-4-wens@csie.org> (raw) In-Reply-To: <20161028101154.7350-1-wens@csie.org> The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with the enabling pin connected to PL2. The AC100 RTC provides a low power clock signal. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 32 +++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 439847acd41e..67b02fe7f11c 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -76,6 +76,14 @@ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &mmc0 { @@ -88,6 +96,21 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_cubieboard4>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc1_pins { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; @@ -128,6 +151,15 @@ status = "okay"; }; +&r_pio { + wifi_en_pin_cubieboard4: wifi_en_pin@0 { + allwinner,pins = "PL2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + &r_rsb { status = "okay"; -- 2.9.3
WARNING: multiple messages have this Message-ID (diff)
From: wens@csie.org (Chen-Yu Tsai) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 3/3] ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi Date: Fri, 28 Oct 2016 18:11:54 +0800 [thread overview] Message-ID: <20161028101154.7350-4-wens@csie.org> (raw) In-Reply-To: <20161028101154.7350-1-wens@csie.org> The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with the enabling pin connected to PL2. The AC100 RTC provides a low power clock signal. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 32 +++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 439847acd41e..67b02fe7f11c 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -76,6 +76,14 @@ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &mmc0 { @@ -88,6 +96,21 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>, <&wifi_en_pin_cubieboard4>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_cldo3>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc1_pins { + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; @@ -128,6 +151,15 @@ status = "okay"; }; +&r_pio { + wifi_en_pin_cubieboard4: wifi_en_pin at 0 { + allwinner,pins = "PL2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + &r_rsb { status = "okay"; -- 2.9.3
next prev parent reply other threads:[~2016-10-28 10:12 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-10-28 10:11 [PATCH 0/3] ARM: dts: sun9i: Enable SDIO-based WiFi Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai 2016-10-28 10:11 ` [PATCH 1/3] ARM: dts: sun9i: Add mmc1 pinmux setting Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai 2016-10-28 10:11 ` [PATCH 2/3] ARM: dts: sun9i: a80-optimus: Enable AP6330 WiFi Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai 2016-10-28 10:11 ` Chen-Yu Tsai [this message] 2016-10-28 10:11 ` [PATCH 3/3] ARM: dts: sun9i: cubieboard4: " Chen-Yu Tsai 2016-11-02 13:32 ` [PATCH 0/3] ARM: dts: sun9i: Enable SDIO-based WiFi Maxime Ripard 2016-11-02 13:32 ` Maxime Ripard
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20161028101154.7350-4-wens@csie.org \ --to=wens@csie.org \ --cc=devicetree@vger.kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=maxime.ripard@free-electrons.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.