[Buildroot] [git commit] configs/mx6sx_udoo_neo: Bump to U-Boot 2017.01

* [Buildroot] [git commit] configs/mx6sx_udoo_neo: Bump to U-Boot 2017.01
@ 2017-01-10 20:05 Peter Korsgaard
  0 siblings, 0 replies; 2+ messages in thread
From: Peter Korsgaard @ 2017-01-10 20:05 UTC (permalink / raw)
  To: buildroot

commit: https://git.buildroot.net/buildroot/commit/?id=a50e9b95bf46372fc74a84528ba2ac7e72214d16
branch: https://git.buildroot.net/buildroot/commit/?id=refs/heads/master

Bump to U-Boot 2017.01, which supports mx6sx_udoo_neo by default.

Remove the U-Boot patch that we used for the previous version.

Also adjust the 'fdtfile' name as it has been changed in U-Boot
mainline.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
---
 board/udoo/neo/patches/uboot/0001-udoo.patch | 691 ---------------------------
 1 file changed, 691 deletions(-)

diff --git a/board/udoo/neo/patches/uboot/0001-udoo.patch b/board/udoo/neo/patches/uboot/0001-udoo.patch
deleted file mode 100644
index ec1e00d..0000000
--- a/board/udoo/neo/patches/uboot/0001-udoo.patch
+++ /dev/null
@@ -1,691 +0,0 @@
-From 792f186846672140deca7dfbf2f20aece26b5348 Mon Sep 17 00:00:00 2001
-From: Breno Lima <breno.lima@nxp.com>
-Date: Fri, 25 Nov 2016 16:56:57 -0200
-Subject: [PATCH] mx6sx: Add initial support for UDOO Neo Board
-
-UDOO Neo Board is a development board from Seco that has three models:
- - UDOO Neo Basic
- - UDOO Neo Basic Kick Starter
- - UDOO Neo Extended
- - UDOO Neo Full
-
-All versions are based on the i.MX6 SoloX processor.
-
-For more details about the UDOO Neo board, please refer to:
-http://www.udoo.org/udoo-neo/
-
-This work is based on a previous commit of Francesco Montefoschi
-<francesco.monte@gmail.com>:
-https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844
-
-Only tested on the UDOO Neo Full board.
-
-Signed-off-by: Breno Lima <breno.lima@nxp.com>
-Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
----
- arch/arm/cpu/armv7/mx6/Kconfig |    5 +
- board/udoo/neo/Kconfig         |   12 ++
- board/udoo/neo/MAINTAINERS     |    7 +
- board/udoo/neo/Makefile        |    6 +
- board/udoo/neo/neo.c           |  441 ++++++++++++++++++++++++++++++++++++++++
- configs/udoo_neo_defconfig     |   30 +++
- include/configs/udoo_neo.h     |   94 +++++++++
- 7 files changed, 595 insertions(+)
- create mode 100644 board/udoo/neo/Kconfig
- create mode 100644 board/udoo/neo/MAINTAINERS
- create mode 100644 board/udoo/neo/Makefile
- create mode 100644 board/udoo/neo/neo.c
- create mode 100644 configs/udoo_neo_defconfig
- create mode 100644 include/configs/udoo_neo.h
-
-diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
-index 8b2217e..a81d944 100644
---- a/arch/arm/cpu/armv7/mx6/Kconfig
-+++ b/arch/arm/cpu/armv7/mx6/Kconfig
-@@ -200,6 +200,10 @@ config TARGET_UDOO
- 	bool "udoo"
- 	select SUPPORT_SPL
- 
-+config TARGET_UDOO_NEO
-+	bool "UDOO Neo"
-+	select SUPPORT_SPL
-+
- config TARGET_WANDBOARD
- 	bool "wandboard"
- 	select SUPPORT_SPL
-@@ -261,6 +265,7 @@ source "board/technexion/pico-imx6ul/Kconfig"
- source "board/tbs/tbs2910/Kconfig"
- source "board/tqc/tqma6/Kconfig"
- source "board/udoo/Kconfig"
-+source "board/udoo/neo/Kconfig"
- source "board/wandboard/Kconfig"
- source "board/warp/Kconfig"
- 
-diff --git a/board/udoo/neo/Kconfig b/board/udoo/neo/Kconfig
-new file mode 100644
-index 0000000..8f474df
---- /dev/null
-+++ b/board/udoo/neo/Kconfig
-@@ -0,0 +1,12 @@
-+if TARGET_UDOO_NEO
-+
-+config SYS_VENDOR
-+	default "udoo"
-+
-+config SYS_BOARD
-+	default "neo"
-+
-+config SYS_CONFIG_NAME
-+	default "udoo_neo"
-+
-+endif
-diff --git a/board/udoo/neo/MAINTAINERS b/board/udoo/neo/MAINTAINERS
-new file mode 100644
-index 0000000..743fe33
---- /dev/null
-+++ b/board/udoo/neo/MAINTAINERS
-@@ -0,0 +1,7 @@
-+UDOO NEO BOARD
-+M:	Breno Lima <breno.lima@nxp.com>
-+M:	Francesco Montefoschi <francesco.montefoschi@udoo.org>
-+S:	Maintained
-+F:	board/udoo/neo/
-+F:	include/configs/udoo_neo.h
-+F:	configs/udoo_neo_defconfig
-diff --git a/board/udoo/neo/Makefile b/board/udoo/neo/Makefile
-new file mode 100644
-index 0000000..150cbc1
---- /dev/null
-+++ b/board/udoo/neo/Makefile
-@@ -0,0 +1,6 @@
-+# (C) Copyright 2015 UDOO Team
-+#
-+# SPDX-License-Identifier:	GPL-2.0+
-+#
-+
-+obj-y  := neo.o
-diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
-new file mode 100644
-index 0000000..7f17469
---- /dev/null
-+++ b/board/udoo/neo/neo.c
-@@ -0,0 +1,441 @@
-+/*
-+ * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
-+ * Copyright (C) Jasbir Matharu
-+ * Copyright (C) UDOO Team
-+ *
-+ * Author: Breno Lima <breno.lima@nxp.com>
-+ * Author: Francesco Montefoschi <francesco.monte@gmail.com>
-+ *
-+ * SPDX-License-Identifier:	GPL-2.0+
-+ */
-+
-+#include <asm/arch/clock.h>
-+#include <asm/arch/imx-regs.h>
-+#include <asm/arch/iomux.h>
-+#include <asm/arch/mx6-pins.h>
-+#include <asm/gpio.h>
-+#include <asm/imx-common/iomux-v3.h>
-+#include <mmc.h>
-+#include <fsl_esdhc.h>
-+#include <asm/arch/crm_regs.h>
-+#include <asm/io.h>
-+#include <asm/arch/sys_proto.h>
-+#include <spl.h>
-+#include <linux/sizes.h>
-+#include <common.h>
-+
-+DECLARE_GLOBAL_DATA_PTR;
-+
-+enum {
-+	UDOO_NEO_TYPE_BASIC,
-+	UDOO_NEO_TYPE_BASIC_KS,
-+	UDOO_NEO_TYPE_FULL,
-+	UDOO_NEO_TYPE_EXTENDED,
-+};
-+
-+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
-+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
-+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-+
-+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
-+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
-+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-+
-+#define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED |	\
-+	PAD_CTL_DSE_40ohm)
-+
-+#define BOARD_DETECT_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
-+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
-+	PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
-+#define BOARD_DETECT_PAD_CFG (MUX_PAD_CTRL(BOARD_DETECT_PAD_CTRL) |	\
-+	MUX_MODE_SION)
-+
-+int dram_init(void)
-+{
-+	gd->ram_size = imx_ddr_size();
-+	return 0;
-+}
-+
-+static iomux_v3_cfg_t const uart1_pads[] = {
-+	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-+	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-+};
-+
-+static iomux_v3_cfg_t const usdhc2_pads[] = {
-+	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	/* CD pin */
-+	MX6_PAD_SD1_DATA0__GPIO6_IO_2 | MUX_PAD_CTRL(NO_PAD_CTRL),
-+	/* Power */
-+	MX6_PAD_SD1_CMD__GPIO6_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL),
-+};
-+
-+static iomux_v3_cfg_t const board_recognition_pads[] = {
-+	/*Connected to R184*/
-+	MX6_PAD_NAND_READY_B__GPIO4_IO_13 | BOARD_DETECT_PAD_CFG,
-+	/*Connected to R185*/
-+	MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG,
-+};
-+
-+static iomux_v3_cfg_t const usdhc3_pads[] = {
-+    /* Configured for WLAN */
-+	MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+	MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-+};
-+
-+static iomux_v3_cfg_t const wdog_b_pad = {
-+	MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL),
-+};
-+
-+static iomux_v3_cfg_t const peri_3v3_pads[] = {
-+	MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL),
-+};
-+
-+static void setup_iomux_uart(void)
-+{
-+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-+}
-+
-+int board_init(void)
-+{
-+	/* Address of boot parameters */
-+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-+
-+	/*
-+	 * Because kernel set WDOG_B mux before pad with the commone pinctrl
-+	 * framwork now and wdog reset will be triggered once set WDOG_B mux
-+	 * with default pad setting, we set pad setting here to workaround this.
-+	 * Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
-+	 * as GPIO mux firstly here to workaround it.
-+	 */
-+	imx_iomux_v3_setup_pad(wdog_b_pad);
-+
-+	/* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */
-+	imx_iomux_v3_setup_multiple_pads(peri_3v3_pads,
-+					 ARRAY_SIZE(peri_3v3_pads));
-+
-+	/* Active high for ncp692 */
-+	gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
-+
-+	return 0;
-+}
-+
-+static int get_board_value(void)
-+{
-+	int r184, r185;
-+
-+	imx_iomux_v3_setup_multiple_pads(board_recognition_pads,
-+					 ARRAY_SIZE(board_recognition_pads));
-+
-+	gpio_direction_input(IMX_GPIO_NR(4, 13));
-+	gpio_direction_input(IMX_GPIO_NR(4, 0));
-+
-+	r184 = gpio_get_value(IMX_GPIO_NR(4, 13));
-+	r185 = gpio_get_value(IMX_GPIO_NR(4, 0));
-+
-+	/*
-+	 * Machine selection -
-+	 * Machine          r184,    r185
-+	 * ---------------------------------
-+	 * Basic              0        0
-+	 * Basic Ks           0        1
-+	 * Full               1        0
-+	 * Extended           1        1
-+	 */
-+
-+	return (r184 << 1) + r185;
-+}
-+
-+int board_early_init_f(void)
-+{
-+	setup_iomux_uart();
-+
-+	return 0;
-+}
-+
-+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
-+	{USDHC2_BASE_ADDR, 0, 4},
-+	{USDHC3_BASE_ADDR, 0, 4},
-+};
-+
-+#define USDHC2_PWR_GPIO IMX_GPIO_NR(6, 1)
-+#define USDHC2_CD_GPIO	IMX_GPIO_NR(6, 2)
-+
-+int board_mmc_getcd(struct mmc *mmc)
-+{
-+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-+	int ret = 0;
-+
-+	switch (cfg->esdhc_base) {
-+	case USDHC2_BASE_ADDR:
-+		ret = !gpio_get_value(USDHC2_CD_GPIO);
-+		break;
-+	}
-+
-+	return ret;
-+}
-+
-+int board_mmc_init(bd_t *bis)
-+{
-+#ifndef CONFIG_SPL_BUILD
-+	int i, ret;
-+
-+	/*
-+	 * According to the board_mmc_init() the following map is done:
-+	 * (U-boot device node)    (Physical Port)
-+	 * mmc0                    USDHC2
-+	 */
-+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
-+		switch (i) {
-+		case 0:
-+			imx_iomux_v3_setup_multiple_pads(
-+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-+			gpio_direction_input(USDHC2_CD_GPIO);
-+			gpio_direction_output(USDHC2_PWR_GPIO, 1);
-+			break;
-+		case 1:
-+			imx_iomux_v3_setup_multiple_pads(
-+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-+			break;
-+		default:
-+			printf("Warning: you configured more USDHC controllers\
-+				(%d) than supported by the board\n", i + 1);
-+			return -EINVAL;
-+			}
-+
-+			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
-+			if (ret) {
-+				printf("Warning:\
-+					failed to initialize mmc dev %d\n", i);
-+				return ret;
-+			}
-+	}
-+
-+	return 0;
-+#else
-+	struct src *src_regs = (struct src *)SRC_BASE_ADDR;
-+	u32 val;
-+	u32 port;
-+
-+	val = readl(&src_regs->sbmr1);
-+
-+	if ((val & 0xc0) != 0x40) {
-+		printf("Not boot from USDHC!\n");
-+		return -EINVAL;
-+	}
-+
-+	port = (val >> 11) & 0x3;
-+	printf("port %d\n", port);
-+	switch (port) {
-+	case 1:
-+		imx_iomux_v3_setup_multiple_pads(
-+			usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
-+		gpio_direction_input(USDHC2_CD_GPIO);
-+		gpio_direction_output(USDHC2_PWR_GPIO, 1);
-+		break;
-+	case 2:
-+		imx_iomux_v3_setup_multiple_pads(
-+			usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-+		usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-+		usdhc_cfg[1].esdhc_base = USDHC3_BASE_ADDR;
-+		break;
-+	}
-+
-+	gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
-+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-+#endif
-+}
-+
-+char *board_string(void)
-+{
-+	switch (get_board_value()) {
-+	case UDOO_NEO_TYPE_BASIC:
-+		return "BASIC";
-+	case UDOO_NEO_TYPE_BASIC_KS:
-+		return "BASICKS";
-+	case UDOO_NEO_TYPE_FULL:
-+		return "FULL";
-+	case UDOO_NEO_TYPE_EXTENDED:
-+		return "EXTENDED";
-+	}
-+	return "UNDEFINED";
-+}
-+
-+int checkboard(void)
-+{
-+	printf("Board: UDOO Neo %s\n", board_string());
-+	return 0;
-+}
-+
-+int board_late_init(void)
-+{
-+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-+	setenv("board_name", board_string());
-+#endif
-+
-+	return 0;
-+}
-+
-+#ifdef CONFIG_SPL_BUILD
-+
-+#include <libfdt.h>
-+#include <asm/arch/mx6-ddr.h>
-+
-+static const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = {
-+	.dram_dqm0 = 0x00000028,
-+	.dram_dqm1 = 0x00000028,
-+	.dram_dqm2 = 0x00000028,
-+	.dram_dqm3 = 0x00000028,
-+	.dram_ras = 0x00000020,
-+	.dram_cas = 0x00000020,
-+	.dram_odt0 = 0x00000020,
-+	.dram_odt1 = 0x00000020,
-+	.dram_sdba2 = 0x00000000,
-+	.dram_sdcke0 = 0x00003000,
-+	.dram_sdcke1 = 0x00003000,
-+	.dram_sdclk_0 = 0x00000030,
-+	.dram_sdqs0 = 0x00000028,
-+	.dram_sdqs1 = 0x00000028,
-+	.dram_sdqs2 = 0x00000028,
-+	.dram_sdqs3 = 0x00000028,
-+	.dram_reset = 0x00000020,
-+};
-+
-+static const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = {
-+	.grp_addds = 0x00000020,
-+	.grp_ddrmode_ctl = 0x00020000,
-+	.grp_ddrpke = 0x00000000,
-+	.grp_ddrmode = 0x00020000,
-+	.grp_b0ds = 0x00000028,
-+	.grp_b1ds = 0x00000028,
-+	.grp_ctlds = 0x00000020,
-+	.grp_ddr_type = 0x000c0000,
-+	.grp_b2ds = 0x00000028,
-+	.grp_b3ds = 0x00000028,
-+};
-+
-+static const struct mx6_mmdc_calibration neo_mmcd_calib = {
-+	.p0_mpwldectrl0 = 0x000E000B,
-+	.p0_mpwldectrl1 = 0x000E0010,
-+	.p0_mpdgctrl0 = 0x41600158,
-+	.p0_mpdgctrl1 = 0x01500140,
-+	.p0_mprddlctl = 0x3A383E3E,
-+	.p0_mpwrdlctl = 0x3A383C38,
-+};
-+
-+static const struct mx6_mmdc_calibration neo_basic_mmcd_calib = {
-+	.p0_mpwldectrl0 = 0x001E0022,
-+	.p0_mpwldectrl1 = 0x001C0019,
-+	.p0_mpdgctrl0 = 0x41540150,
-+	.p0_mpdgctrl1 = 0x01440138,
-+	.p0_mprddlctl = 0x403E4644,
-+	.p0_mpwrdlctl = 0x3C3A4038,
-+};
-+
-+/* MT41K256M16 */
-+static struct mx6_ddr3_cfg neo_mem_ddr = {
-+	.mem_speed = 1600,
-+	.density = 4,
-+	.width = 16,
-+	.banks = 8,
-+	.rowaddr = 15,
-+	.coladdr = 10,
-+	.pagesz = 2,
-+	.trcd = 1375,
-+	.trcmin = 4875,
-+	.trasmin = 3500,
-+};
-+
-+/* MT41K128M16 */
-+static struct mx6_ddr3_cfg neo_basic_mem_ddr = {
-+	.mem_speed = 1600,
-+	.density = 2,
-+	.width = 16,
-+	.banks = 8,
-+	.rowaddr = 14,
-+	.coladdr = 10,
-+	.pagesz = 2,
-+	.trcd = 1375,
-+	.trcmin = 4875,
-+	.trasmin = 3500,
-+};
-+
-+static void ccgr_init(void)
-+{
-+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-+
-+	writel(0xFFFFFFFF, &ccm->CCGR0);
-+	writel(0xFFFFFFFF, &ccm->CCGR1);
-+	writel(0xFFFFFFFF, &ccm->CCGR2);
-+	writel(0xFFFFFFFF, &ccm->CCGR3);
-+	writel(0xFFFFFFFF, &ccm->CCGR4);
-+	writel(0xFFFFFFFF, &ccm->CCGR5);
-+	writel(0xFFFFFFFF, &ccm->CCGR6);
-+	writel(0xFFFFFFFF, &ccm->CCGR7);
-+}
-+
-+static void spl_dram_init(void)
-+{
-+	int board = get_board_value();
-+
-+	struct mx6_ddr_sysinfo sysinfo = {
-+		.dsize = 1, /* width of data bus: 1 = 32 bits */
-+		.cs_density = 24,
-+		.ncs = 1,
-+		.cs1_mirror = 0,
-+		.rtt_wr = 2,
-+		.rtt_nom = 2,		/* RTT_Nom = RZQ/2 */
-+		.walat = 1,		/* Write additional latency */
-+		.ralat = 5,		/* Read additional latency */
-+		.mif3_mode = 3,		/* Command prediction working mode */
-+		.bi_on = 1,		/* Bank interleaving enabled */
-+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
-+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
-+	};
-+
-+	mx6sx_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs);
-+	if (board == UDOO_NEO_TYPE_BASIC || board == UDOO_NEO_TYPE_BASIC_KS)
-+		mx6_dram_cfg(&sysinfo, &neo_basic_mmcd_calib,
-+			     &neo_basic_mem_ddr);
-+	else
-+		mx6_dram_cfg(&sysinfo, &neo_mmcd_calib, &neo_mem_ddr);
-+}
-+
-+void board_init_f(ulong dummy)
-+{
-+	ccgr_init();
-+
-+	/* setup AIPS and disable watchdog */
-+	arch_cpu_init();
-+
-+	board_early_init_f();
-+
-+	/* setup GP timer */
-+	timer_init();
-+
-+	/* UART clocks enabled and gd valid - init serial console */
-+	preloader_console_init();
-+
-+	/* DDR initialization */
-+	spl_dram_init();
-+
-+	/* Clear the BSS. */
-+	memset(__bss_start, 0, __bss_end - __bss_start);
-+
-+	/* load/boot image from boot device */
-+	board_init_r(NULL, 0);
-+}
-+
-+#endif
-diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
-new file mode 100644
-index 0000000..3304afb
---- /dev/null
-+++ b/configs/udoo_neo_defconfig
-@@ -0,0 +1,30 @@
-+CONFIG_ARM=y
-+CONFIG_ARCH_MX6=y
-+CONFIG_SPL_GPIO_SUPPORT=y
-+CONFIG_SPL_LIBCOMMON_SUPPORT=y
-+CONFIG_SPL_LIBGENERIC_SUPPORT=y
-+CONFIG_TARGET_UDOO_NEO=y
-+CONFIG_SPL_EXT_SUPPORT=y
-+CONFIG_SPL_LIBDISK_SUPPORT=y
-+CONFIG_SPL_MMC_SUPPORT=y
-+CONFIG_SPL_SERIAL_SUPPORT=y
-+CONFIG_SPL_ENV_SUPPORT=y
-+CONFIG_SPL_WATCHDOG_SUPPORT=y
-+CONFIG_SPL=y
-+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6SX"
-+CONFIG_HUSH_PARSER=y
-+CONFIG_CMD_BOOTZ=y
-+# CONFIG_CMD_IMLS is not set
-+# CONFIG_CMD_FLASH is not set
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_GPIO=y
-+# CONFIG_CMD_SETEXPR is not set
-+# CONFIG_CMD_DHCP=y
-+CONFIG_CMD_CACHE=y
-+CONFIG_CMD_TIME=y
-+CONFIG_CMD_EXT2=y
-+CONFIG_CMD_EXT4=y
-+CONFIG_CMD_EXT4_WRITE=y
-+CONFIG_CMD_FAT=y
-+CONFIG_CMD_FS_GENERIC=y
-+CONFIG_OF_LIBFDT=y
-diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
-new file mode 100644
-index 0000000..81e0481
---- /dev/null
-+++ b/include/configs/udoo_neo.h
-@@ -0,0 +1,94 @@
-+/*
-+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
-+ * Copyright Jasbir Matharu
-+ * Copyright 2015 UDOO Team
-+ *
-+ * Configuration settings for the UDOO NEO board.
-+ *
-+ * SPDX-License-Identifier:	GPL-2.0+
-+ */
-+
-+#ifndef __CONFIG_H
-+#define __CONFIG_H
-+
-+#include <config_distro_defaults.h>
-+#include "mx6_common.h"
-+
-+#include "imx6_spl.h"
-+
-+/* Size of malloc() pool */
-+#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
-+#define CONFIG_BOARD_EARLY_INIT_F
-+#define CONFIG_BOARD_LATE_INIT
-+#define CONFIG_MXC_UART
-+
-+/* MMC Configuration */
-+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
-+
-+/* Command definition */
-+#define CONFIG_MXC_UART_BASE		UART1_BASE
-+#define CONFIG_SYS_FSL_USDHC_NUM	2
-+#define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC2*/
-+
-+/* Linux only */
-+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-+#define CONFIG_EXTRA_ENV_SETTINGS \
-+	"console=ttymxc0,115200\0" \
-+	"fdt_high=0xffffffff\0" \
-+	"initrd_high=0xffffffff\0" \
-+	"fdt_file=undefined\0" \
-+	"fdt_addr=0x83000000\0" \
-+	"ip_dyn=yes\0" \
-+	"mmcdev=0\0" \
-+	"mmcrootfstype=ext4\0" \
-+	"mmcautodetect=no\0" \
-+	"findfdt="\
-+		"if test $board_name = BASIC; then " \
-+			"setenv fdt_file imx6sx-udoo-neo-basic.dtb; fi; " \
-+		"if test $board_name = BASICKS; then " \
-+			"setenv fdt_file imx6sx-udoo-neo-basic.dtb; fi; " \
-+		"if test $board_name = FULL; then " \
-+			"setenv fdt_file imx6sx-udoo-neo-full.dtb; fi; " \
-+		"if test $board_name = EXTENDED; then " \
-+			"setenv fdt_file imx6sx-udoo-neo-extended.dtb; fi; " \
-+		"if test $fdt_file = UNDEFINED; then " \
-+			"echo WARNING: Could not determine dtb to use; fi; \0" \
-+	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
-+	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
-+	"ramdisk_addr_r=0x83000000\0" \
-+	"ramdiskaddr=0x83000000\0" \
-+	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
-+	BOOTENV
-+
-+#define BOOT_TARGET_DEVICES(func) \
-+	func(MMC, mmc, 0)
-+
-+#define CONFIG_BOOTCOMMAND \
-+	"run findfdt; " \
-+	"run distro_bootcmd"
-+
-+#include <config_distro_bootcmd.h>
-+
-+/* Miscellaneous configurable options */
-+#define CONFIG_SYS_MEMTEST_START	0x80000000
-+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
-+#define CONFIG_STACKSIZE		SZ_128K
-+
-+/* Physical Memory Map */
-+#define CONFIG_NR_DRAM_BANKS		1
-+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-+
-+#define CONFIG_SYS_INIT_SP_OFFSET \
-+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-+#define CONFIG_SYS_INIT_SP_ADDR \
-+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-+
-+/* Environment organization */
-+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
-+#define CONFIG_ENV_SIZE			SZ_8K
-+#define CONFIG_ENV_IS_IN_MMC
-+
-+#endif				/* __CONFIG_H */
--- 
-1.7.10.4

^ permalink raw reply related	[flat|nested] 2+ messages in thread