* [PATCH v4 2/5] cfg80211: Pass new RSSI level in CQM RSSI notification
2017-01-25 11:43 [PATCH v4 1/5] mac80211: Pass new RSSI level in CQM RSSI notification Andrew Zaborowski
@ 2017-01-25 11:43 ` Andrew Zaborowski
2017-02-08 9:47 ` Johannes Berg
2017-01-25 11:43 ` [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM Andrew Zaborowski
` (2 subsequent siblings)
3 siblings, 1 reply; 12+ messages in thread
From: Andrew Zaborowski @ 2017-01-25 11:43 UTC (permalink / raw)
To: linux-wireless
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
---
drivers/net/wireless/marvell/mwifiex/sta_event.c | 4 ++--
drivers/net/wireless/rndis_wlan.c | 2 +-
include/net/cfg80211.h | 3 ++-
include/uapi/linux/nl80211.h | 3 +++
net/mac80211/mlme.c | 2 +-
net/wireless/nl80211.c | 9 +++++++--
net/wireless/trace.h | 11 +++++++----
7 files changed, 23 insertions(+), 11 deletions(-)
diff --git a/drivers/net/wireless/marvell/mwifiex/sta_event.c b/drivers/net/wireless/marvell/mwifiex/sta_event.c
index 9df0c4d..5cc3aa7 100644
--- a/drivers/net/wireless/marvell/mwifiex/sta_event.c
+++ b/drivers/net/wireless/marvell/mwifiex/sta_event.c
@@ -824,7 +824,7 @@ int mwifiex_process_sta_event(struct mwifiex_private *priv)
case EVENT_RSSI_LOW:
cfg80211_cqm_rssi_notify(priv->netdev,
NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
- GFP_KERNEL);
+ 0, GFP_KERNEL);
mwifiex_send_cmd(priv, HostCmd_CMD_RSSI_INFO,
HostCmd_ACT_GEN_GET, 0, NULL, false);
priv->subsc_evt_rssi_state = RSSI_LOW_RECVD;
@@ -839,7 +839,7 @@ int mwifiex_process_sta_event(struct mwifiex_private *priv)
case EVENT_RSSI_HIGH:
cfg80211_cqm_rssi_notify(priv->netdev,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
- GFP_KERNEL);
+ 0, GFP_KERNEL);
mwifiex_send_cmd(priv, HostCmd_CMD_RSSI_INFO,
HostCmd_ACT_GEN_GET, 0, NULL, false);
priv->subsc_evt_rssi_state = RSSI_HIGH_RECVD;
diff --git a/drivers/net/wireless/rndis_wlan.c b/drivers/net/wireless/rndis_wlan.c
index 603c904..785334f 100644
--- a/drivers/net/wireless/rndis_wlan.c
+++ b/drivers/net/wireless/rndis_wlan.c
@@ -3187,7 +3187,7 @@ static void rndis_do_cqm(struct usbnet *usbdev, s32 rssi)
return;
priv->last_cqm_event_rssi = rssi;
- cfg80211_cqm_rssi_notify(usbdev->net, event, GFP_KERNEL);
+ cfg80211_cqm_rssi_notify(usbdev->net, event, rssi, GFP_KERNEL);
}
#define DEVICE_POLLER_JIFFIES (HZ)
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 57383a1..9adff4e 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -5303,6 +5303,7 @@ void cfg80211_mgmt_tx_status(struct wireless_dev *wdev, u64 cookie,
* cfg80211_cqm_rssi_notify - connection quality monitoring rssi event
* @dev: network device
* @rssi_event: the triggered RSSI event
+ * @rssi_level: new RSSI level value or 0 if not available
* @gfp: context flags
*
* This function is called when a configured connection quality monitoring
@@ -5310,7 +5311,7 @@ void cfg80211_mgmt_tx_status(struct wireless_dev *wdev, u64 cookie,
*/
void cfg80211_cqm_rssi_notify(struct net_device *dev,
enum nl80211_cqm_rssi_threshold_event rssi_event,
- gfp_t gfp);
+ s32 rssi_level, gfp_t gfp);
/**
* cfg80211_cqm_pktloss_notify - notify userspace about packetloss to peer
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 455ed9b..5cd7a81 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -3918,6 +3918,8 @@ enum nl80211_ps_state {
* %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting.
* @NL80211_ATTR_CQM_BEACON_LOSS_EVENT: flag attribute that's set in a beacon
* loss event
+ * @NL80211_ATTR_CQM_RSSI_LEVEL: the RSSI value in dBm that triggered the
+ * RSSI threshold event.
* @__NL80211_ATTR_CQM_AFTER_LAST: internal
* @NL80211_ATTR_CQM_MAX: highest key attribute
*/
@@ -3931,6 +3933,7 @@ enum nl80211_attr_cqm {
NL80211_ATTR_CQM_TXE_PKTS,
NL80211_ATTR_CQM_TXE_INTVL,
NL80211_ATTR_CQM_BEACON_LOSS_EVENT,
+ NL80211_ATTR_CQM_RSSI_LEVEL,
/* keep last */
__NL80211_ATTR_CQM_AFTER_LAST,
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index a40b90b..0cfa215 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -5052,7 +5052,7 @@ void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
trace_api_cqm_rssi_notify(sdata, rssi_event, rssi_level);
- cfg80211_cqm_rssi_notify(sdata->dev, rssi_event, gfp);
+ cfg80211_cqm_rssi_notify(sdata->dev, rssi_event, rssi_level, gfp);
}
EXPORT_SYMBOL(ieee80211_cqm_rssi_notify);
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index cc05d36..7749687 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -9386,6 +9386,7 @@ nl80211_attr_cqm_policy[NL80211_ATTR_CQM_MAX + 1] = {
[NL80211_ATTR_CQM_TXE_RATE] = { .type = NLA_U32 },
[NL80211_ATTR_CQM_TXE_PKTS] = { .type = NLA_U32 },
[NL80211_ATTR_CQM_TXE_INTVL] = { .type = NLA_U32 },
+ [NL80211_ATTR_CQM_RSSI_LEVEL] = { .type = NLA_S32 },
};
static int nl80211_set_cqm_txe(struct genl_info *info,
@@ -13873,11 +13874,11 @@ static void cfg80211_send_cqm(struct sk_buff *msg, gfp_t gfp)
void cfg80211_cqm_rssi_notify(struct net_device *dev,
enum nl80211_cqm_rssi_threshold_event rssi_event,
- gfp_t gfp)
+ s32 rssi_level, gfp_t gfp)
{
struct sk_buff *msg;
- trace_cfg80211_cqm_rssi_notify(dev, rssi_event);
+ trace_cfg80211_cqm_rssi_notify(dev, rssi_event, rssi_level);
if (WARN_ON(rssi_event != NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW &&
rssi_event != NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH))
@@ -13891,6 +13892,10 @@ void cfg80211_cqm_rssi_notify(struct net_device *dev,
rssi_event))
goto nla_put_failure;
+ if (rssi_level && nla_put_s32(msg, NL80211_ATTR_CQM_RSSI_LEVEL,
+ rssi_level))
+ goto nla_put_failure;
+
cfg80211_send_cqm(msg, gfp);
return;
diff --git a/net/wireless/trace.h b/net/wireless/trace.h
index ea1b47e..2419c39 100644
--- a/net/wireless/trace.h
+++ b/net/wireless/trace.h
@@ -2490,18 +2490,21 @@ TRACE_EVENT(cfg80211_mgmt_tx_status,
TRACE_EVENT(cfg80211_cqm_rssi_notify,
TP_PROTO(struct net_device *netdev,
- enum nl80211_cqm_rssi_threshold_event rssi_event),
- TP_ARGS(netdev, rssi_event),
+ enum nl80211_cqm_rssi_threshold_event rssi_event,
+ s32 rssi_level),
+ TP_ARGS(netdev, rssi_event, rssi_level),
TP_STRUCT__entry(
NETDEV_ENTRY
__field(enum nl80211_cqm_rssi_threshold_event, rssi_event)
+ __field(s32, rssi_level)
),
TP_fast_assign(
NETDEV_ASSIGN;
__entry->rssi_event = rssi_event;
+ __entry->rssi_level = rssi_level;
),
- TP_printk(NETDEV_PR_FMT ", rssi event: %d",
- NETDEV_PR_ARG, __entry->rssi_event)
+ TP_printk(NETDEV_PR_FMT ", rssi event: %d, level: %d",
+ NETDEV_PR_ARG, __entry->rssi_event, __entry->rssi_level)
);
TRACE_EVENT(cfg80211_reg_can_beacon,
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-01-25 11:43 [PATCH v4 1/5] mac80211: Pass new RSSI level in CQM RSSI notification Andrew Zaborowski
2017-01-25 11:43 ` [PATCH v4 2/5] cfg80211: " Andrew Zaborowski
@ 2017-01-25 11:43 ` Andrew Zaborowski
2017-02-08 9:58 ` Johannes Berg
2017-01-25 11:43 ` [PATCH v4 4/5] mac80211: Add set_cqm_rssi_range_config Andrew Zaborowski
2017-01-25 11:43 ` [PATCH v4 5/5] wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple drivers Andrew Zaborowski
3 siblings, 1 reply; 12+ messages in thread
From: Andrew Zaborowski @ 2017-01-25 11:43 UTC (permalink / raw)
To: linux-wireless
Change the SET CQM command's RSSI threshold attribute to accept any
number of thresholds as a sorted array. The API should be backwards
compatible so that if one s32 threshold value is passed, the old
mechanism is enabled. The netlink event generated is the same in both
cases.
cfg80211 handles an arbitrary number of RSSI thresholds but drivers have
to provide a method (set_cqm_rssi_range_config) that configures a range
set by a high and a low value. Drivers have to call back when the RSSI
goes out of that range and there's no additional event every time the
range is reconfigured as there was with the current API.
This method doesn't have a hysteresis parameter because there's no
benefit to the cfg80211 code from having the hysteresis be handled by
hardware/driver in terms of the number of wakeups. At the same time
it would likely be less consistent between drivers if offloaded or
done in the drivers.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
---
changes in v3:
- define NL80211_EXT_FEATURE_CQM_RSSI_LIST which drivers need to set
if they implement set_cqm_rssi_range_config (mac80211 is a special
case)
- error check the kzalloc in nl80211_set_cqm_rssi
- add a rdev->ops->get_station check before calling get_station
changes in v4:
- simplify the case of disabling CQM in nl80211_set_cqm_rssi
---
include/net/cfg80211.h | 13 ++++
include/uapi/linux/nl80211.h | 9 ++-
net/wireless/core.c | 9 +++
net/wireless/core.h | 9 +++
net/wireless/nl80211.c | 145 +++++++++++++++++++++++++++++++++++++++----
net/wireless/rdev-ops.h | 12 ++++
net/wireless/trace.h | 22 +++++++
7 files changed, 205 insertions(+), 14 deletions(-)
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 9adff4e..bb84edb 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -2660,6 +2660,11 @@ struct cfg80211_nan_func {
* the current level is above/below the configured threshold; this may
* need some care when the configuration is changed (without first being
* disabled.)
+ * @set_cqm_rssi_range_config: Configure two RSSI thresholds in the
+ * connection quality monitor. An event is to be sent only when the
+ * signal level is found to be outside the two values. The driver should
+ * set %NL80211_EXT_FEATURE_CQM_RSSI_LIST if this method is implemented.
+ * If it is provided then there's no point providing @set_cqm_rssi_config.
* @set_cqm_txe_config: Configure connection quality monitor TX error
* thresholds.
* @sched_scan_start: Tell the driver to start a scheduled scan.
@@ -2949,6 +2954,10 @@ struct cfg80211_ops {
struct net_device *dev,
s32 rssi_thold, u32 rssi_hyst);
+ int (*set_cqm_rssi_range_config)(struct wiphy *wiphy,
+ struct net_device *dev,
+ s32 rssi_low, s32 rssi_high);
+
int (*set_cqm_txe_config)(struct wiphy *wiphy,
struct net_device *dev,
u32 rate, u32 pkts, u32 intvl);
@@ -3782,6 +3791,7 @@ void wiphy_free(struct wiphy *wiphy);
struct cfg80211_conn;
struct cfg80211_internal_bss;
struct cfg80211_cached_keys;
+struct cfg80211_cqm_config;
/**
* struct wireless_dev - wireless device state
@@ -3845,6 +3855,7 @@ struct cfg80211_cached_keys;
* @event_list: (private) list for internal event processing
* @event_lock: (private) lock for event list
* @owner_nlportid: (private) owner socket port ID
+ * @cqm_config: (private) nl80211 RSSI monitor state
*/
struct wireless_dev {
struct wiphy *wiphy;
@@ -3913,6 +3924,8 @@ struct wireless_dev {
bool prev_bssid_valid;
} wext;
#endif
+
+ struct cfg80211_cqm_config *cqm_config;
};
static inline u8 *wdev_address(struct wireless_dev *wdev)
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 5cd7a81..e011b75 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -3898,7 +3898,10 @@ enum nl80211_ps_state {
* @__NL80211_ATTR_CQM_INVALID: invalid
* @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies
* the threshold for the RSSI level at which an event will be sent. Zero
- * to disable.
+ * to disable. Alternatively, if %NL80211_EXT_FEATURE_CQM_RSSI_LIST is
+ * set, multiple values can be supplied as a low-to-high sorted array of
+ * threshold values in dBm. Events will be sent when the RSSI value
+ * crosses any of the thresholds.
* @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies
* the minimum amount the RSSI level must change after an event before a
* new event may be issued (to reduce effects of RSSI oscillation).
@@ -4702,6 +4705,9 @@ enum nl80211_feature_flags {
* configuration (AP/mesh) with VHT rates.
* @NL80211_EXT_FEATURE_FILS_STA: This driver supports Fast Initial Link Setup
* with user space SME (NL80211_CMD_AUTHENTICATE) in station mode.
+ * @NL80211_EXT_FEATURE_CQM_RSSI_LIST: This driver accepts lists of RSSI
+ * threshold values to monitor in the %NL80211_ATTR_CQM_RSSI_THOLD
+ * attribute rather than exactly one threshold.
*
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
@@ -4717,6 +4723,7 @@ enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_BEACON_RATE_HT,
NL80211_EXT_FEATURE_BEACON_RATE_VHT,
NL80211_EXT_FEATURE_FILS_STA,
+ NL80211_EXT_FEATURE_CQM_RSSI_LIST,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
diff --git a/net/wireless/core.c b/net/wireless/core.c
index 903fc41..7f5760c 100644
--- a/net/wireless/core.c
+++ b/net/wireless/core.c
@@ -953,6 +953,12 @@ void wiphy_rfkill_set_hw_state(struct wiphy *wiphy, bool blocked)
}
EXPORT_SYMBOL(wiphy_rfkill_set_hw_state);
+void cfg80211_cqm_config_free(struct wireless_dev *wdev)
+{
+ kfree(wdev->cqm_config);
+ wdev->cqm_config = NULL;
+}
+
void cfg80211_unregister_wdev(struct wireless_dev *wdev)
{
struct cfg80211_registered_device *rdev = wiphy_to_rdev(wdev->wiphy);
@@ -979,6 +985,8 @@ void cfg80211_unregister_wdev(struct wireless_dev *wdev)
WARN_ON_ONCE(1);
break;
}
+
+ cfg80211_cqm_config_free(wdev);
}
EXPORT_SYMBOL(cfg80211_unregister_wdev);
@@ -1233,6 +1241,7 @@ static int cfg80211_netdev_notifier_call(struct notifier_block *nb,
kzfree(wdev->wext.keys);
#endif
flush_work(&wdev->disconnect_wk);
+ cfg80211_cqm_config_free(wdev);
}
/*
* synchronise (so that we won't find this netdev
diff --git a/net/wireless/core.h b/net/wireless/core.h
index 9d1a030..c8e218b 100644
--- a/net/wireless/core.h
+++ b/net/wireless/core.h
@@ -271,6 +271,13 @@ struct cfg80211_iface_destroy {
u32 nlportid;
};
+struct cfg80211_cqm_config {
+ u32 rssi_hyst;
+ s32 last_rssi_event_value;
+ int n_rssi_thresholds;
+ s32 rssi_thresholds[0];
+};
+
void cfg80211_destroy_ifaces(struct cfg80211_registered_device *rdev);
/* free object */
@@ -507,4 +514,6 @@ void cfg80211_stop_nan(struct cfg80211_registered_device *rdev,
#define CFG80211_DEV_WARN_ON(cond) ({bool __r = (cond); __r; })
#endif
+void cfg80211_cqm_config_free(struct wireless_dev *wdev);
+
#endif /* __NET_WIRELESS_CORE_H */
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 7749687..623bf0a 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -9380,7 +9380,7 @@ static int nl80211_get_power_save(struct sk_buff *skb, struct genl_info *info)
static const struct nla_policy
nl80211_attr_cqm_policy[NL80211_ATTR_CQM_MAX + 1] = {
- [NL80211_ATTR_CQM_RSSI_THOLD] = { .type = NLA_U32 },
+ [NL80211_ATTR_CQM_RSSI_THOLD] = { .type = NLA_BINARY },
[NL80211_ATTR_CQM_RSSI_HYST] = { .type = NLA_U32 },
[NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT] = { .type = NLA_U32 },
[NL80211_ATTR_CQM_TXE_RATE] = { .type = NLA_U32 },
@@ -9409,28 +9409,130 @@ static int nl80211_set_cqm_txe(struct genl_info *info,
return rdev_set_cqm_txe_config(rdev, dev, rate, pkts, intvl);
}
+static int cfg80211_cqm_rssi_update(struct cfg80211_registered_device *rdev,
+ struct net_device *dev)
+{
+ struct wireless_dev *wdev = dev->ieee80211_ptr;
+ s32 last, low, high;
+ u32 hyst;
+ int i, n;
+ int err;
+
+ /* RSSI reporting disabled? */
+ if (!wdev->cqm_config)
+ return rdev_set_cqm_rssi_range_config(rdev, dev, 0, 0);
+
+ /*
+ * Obtain current RSSI value if possible, if not and no RSSI threshold
+ * event has been received yet, we should receive an event after a
+ * connection is established and enough beacons received to calculate
+ * the average.
+ */
+ if (!wdev->cqm_config->last_rssi_event_value && wdev->current_bss &&
+ rdev->ops->get_station) {
+ struct station_info sinfo;
+ u8 *mac_addr;
+
+ mac_addr = wdev->current_bss->pub.bssid;
+
+ err = rdev_get_station(rdev, dev, mac_addr, &sinfo);
+ if (err)
+ return err;
+
+ if (sinfo.filled & BIT(NL80211_STA_INFO_BEACON_SIGNAL_AVG))
+ wdev->cqm_config->last_rssi_event_value =
+ (s8) sinfo.rx_beacon_signal_avg;
+ }
+
+ if (!wiphy_ext_feature_isset(&rdev->wiphy,
+ NL80211_EXT_FEATURE_CQM_RSSI_LIST))
+ return -EOPNOTSUPP;
+
+ last = wdev->cqm_config->last_rssi_event_value;
+ hyst = wdev->cqm_config->rssi_hyst;
+ n = wdev->cqm_config->n_rssi_thresholds;
+
+ for (i = 0; i < n; i++)
+ if (last < wdev->cqm_config->rssi_thresholds[i])
+ break;
+
+ low = i > 0 ? wdev->cqm_config->rssi_thresholds[i - 1] : S32_MIN;
+ high = i < n ? wdev->cqm_config->rssi_thresholds[i] : S32_MAX;
+
+ if (low > (s32) (last - hyst))
+ low = last - hyst;
+ if (high < (s32) (last + hyst))
+ high = last + hyst;
+
+ return rdev_set_cqm_rssi_range_config(rdev, dev, low, high - 1);
+}
+
static int nl80211_set_cqm_rssi(struct genl_info *info,
- s32 threshold, u32 hysteresis)
+ const s32 *thresholds, int n_thresholds,
+ u32 hysteresis)
{
struct cfg80211_registered_device *rdev = info->user_ptr[0];
struct net_device *dev = info->user_ptr[1];
struct wireless_dev *wdev = dev->ieee80211_ptr;
+ int i, err;
+ s32 prev = S32_MIN;
- if (threshold > 0)
- return -EINVAL;
-
- /* disabling - hysteresis should also be zero then */
- if (threshold == 0)
- hysteresis = 0;
+ /* Check all values negative and sorted */
+ for (i = 0; i < n_thresholds; i++) {
+ if (thresholds[i] > 0 || thresholds[i] <= prev)
+ return -EINVAL;
- if (!rdev->ops->set_cqm_rssi_config)
- return -EOPNOTSUPP;
+ prev = thresholds[i];
+ }
if (wdev->iftype != NL80211_IFTYPE_STATION &&
wdev->iftype != NL80211_IFTYPE_P2P_CLIENT)
return -EOPNOTSUPP;
- return rdev_set_cqm_rssi_config(rdev, dev, threshold, hysteresis);
+ wdev_lock(wdev);
+ cfg80211_cqm_config_free(wdev);
+ wdev_unlock(wdev);
+
+ if (n_thresholds <= 1 && rdev->ops->set_cqm_rssi_config) {
+ if (n_thresholds == 0 || thresholds[0] == 0) /* Disabling */
+ return rdev_set_cqm_rssi_config(rdev, dev, 0, 0);
+
+ return rdev_set_cqm_rssi_config(rdev, dev,
+ thresholds[0], hysteresis);
+ }
+
+ if (!wiphy_ext_feature_isset(&rdev->wiphy,
+ NL80211_EXT_FEATURE_CQM_RSSI_LIST))
+ return -EOPNOTSUPP;
+
+ if (n_thresholds == 1 && thresholds[0] == 0) /* Disabling */
+ n_thresholds = 0;
+
+ wdev_lock(wdev);
+ if (n_thresholds) {
+ struct cfg80211_cqm_config *cqm_config;
+
+ cqm_config = kzalloc(sizeof(struct cfg80211_cqm_config) +
+ n_thresholds * sizeof(s32), GFP_KERNEL);
+ if (!cqm_config) {
+ err = -ENOMEM;
+ goto unlock;
+ }
+
+ cqm_config->rssi_hyst = hysteresis;
+ cqm_config->n_rssi_thresholds = n_thresholds;
+ memcpy(cqm_config->rssi_thresholds, thresholds,
+ n_thresholds * sizeof(s32));
+
+ wdev->cqm_config = cqm_config;
+ }
+
+ err = cfg80211_cqm_rssi_update(rdev, dev);
+
+unlock:
+ wdev_unlock(wdev);
+
+ return err;
}
static int nl80211_set_cqm(struct sk_buff *skb, struct genl_info *info)
@@ -9450,10 +9552,16 @@ static int nl80211_set_cqm(struct sk_buff *skb, struct genl_info *info)
if (attrs[NL80211_ATTR_CQM_RSSI_THOLD] &&
attrs[NL80211_ATTR_CQM_RSSI_HYST]) {
- s32 threshold = nla_get_s32(attrs[NL80211_ATTR_CQM_RSSI_THOLD]);
+ const s32 *thresholds =
+ nla_data(attrs[NL80211_ATTR_CQM_RSSI_THOLD]);
+ int len = nla_len(attrs[NL80211_ATTR_CQM_RSSI_THOLD]);
u32 hysteresis = nla_get_u32(attrs[NL80211_ATTR_CQM_RSSI_HYST]);
- return nl80211_set_cqm_rssi(info, threshold, hysteresis);
+ if (len % 4)
+ return -EINVAL;
+
+ return nl80211_set_cqm_rssi(info, thresholds, len / 4,
+ hysteresis);
}
if (attrs[NL80211_ATTR_CQM_TXE_RATE] &&
@@ -13877,6 +13985,8 @@ void cfg80211_cqm_rssi_notify(struct net_device *dev,
s32 rssi_level, gfp_t gfp)
{
struct sk_buff *msg;
+ struct wireless_dev *wdev = dev->ieee80211_ptr;
+ struct cfg80211_registered_device *rdev = wiphy_to_rdev(wdev->wiphy);
trace_cfg80211_cqm_rssi_notify(dev, rssi_event, rssi_level);
@@ -13884,6 +13994,15 @@ void cfg80211_cqm_rssi_notify(struct net_device *dev,
rssi_event != NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH))
return;
+ if (wdev->cqm_config) {
+ wdev->cqm_config->last_rssi_event_value = rssi_level;
+
+ cfg80211_cqm_rssi_update(rdev, dev);
+
+ if (rssi_level == 0)
+ rssi_level = wdev->cqm_config->last_rssi_event_value;
+ }
+
msg = cfg80211_prepare_cqm(dev, NULL, gfp);
if (!msg)
return;
diff --git a/net/wireless/rdev-ops.h b/net/wireless/rdev-ops.h
index 2f42507..f2baf59 100644
--- a/net/wireless/rdev-ops.h
+++ b/net/wireless/rdev-ops.h
@@ -750,6 +750,18 @@ rdev_set_cqm_rssi_config(struct cfg80211_registered_device *rdev,
}
static inline int
+rdev_set_cqm_rssi_range_config(struct cfg80211_registered_device *rdev,
+ struct net_device *dev, s32 low, s32 high)
+{
+ int ret;
+ trace_rdev_set_cqm_rssi_range_config(&rdev->wiphy, dev, low, high);
+ ret = rdev->ops->set_cqm_rssi_range_config(&rdev->wiphy, dev,
+ low, high);
+ trace_rdev_return_int(&rdev->wiphy, ret);
+ return ret;
+}
+
+static inline int
rdev_set_cqm_txe_config(struct cfg80211_registered_device *rdev,
struct net_device *dev, u32 rate, u32 pkts, u32 intvl)
{
diff --git a/net/wireless/trace.h b/net/wireless/trace.h
index 2419c39..4e6dab3 100644
--- a/net/wireless/trace.h
+++ b/net/wireless/trace.h
@@ -1322,6 +1322,28 @@ TRACE_EVENT(rdev_set_cqm_rssi_config,
__entry->rssi_thold, __entry->rssi_hyst)
);
+TRACE_EVENT(rdev_set_cqm_rssi_range_config,
+ TP_PROTO(struct wiphy *wiphy,
+ struct net_device *netdev, s32 low, s32 high),
+ TP_ARGS(wiphy, netdev, low, high),
+ TP_STRUCT__entry(
+ WIPHY_ENTRY
+ NETDEV_ENTRY
+ __field(s32, rssi_low)
+ __field(s32, rssi_high)
+ ),
+ TP_fast_assign(
+ WIPHY_ASSIGN;
+ NETDEV_ASSIGN;
+ __entry->rssi_low = low;
+ __entry->rssi_high = high;
+ ),
+ TP_printk(WIPHY_PR_FMT ", " NETDEV_PR_FMT
+ ", range: %d - %d ",
+ WIPHY_PR_ARG, NETDEV_PR_ARG,
+ __entry->rssi_low, __entry->rssi_high)
+);
+
TRACE_EVENT(rdev_set_cqm_txe_config,
TP_PROTO(struct wiphy *wiphy, struct net_device *netdev, u32 rate,
u32 pkts, u32 intvl),
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-01-25 11:43 ` [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM Andrew Zaborowski
@ 2017-02-08 9:58 ` Johannes Berg
2017-02-08 11:26 ` Andrew Zaborowski
0 siblings, 1 reply; 12+ messages in thread
From: Johannes Berg @ 2017-02-08 9:58 UTC (permalink / raw)
To: Andrew Zaborowski, linux-wireless
> This method doesn't have a hysteresis parameter because there's no
> benefit to the cfg80211 code from having the hysteresis be handled by
> hardware/driver in terms of the number of wakeups. At the same time
> it would likely be less consistent between drivers if offloaded or
> done in the drivers.
I'm not really sure I buy this.
What if I configure a few ranges, and let's say one of the boundaries
is -50dBm. Now if I sit just on that value of -50dBm and thus my signal
fluctuates say -48..-52, I'd have to continuously wake up the host.
You try to avoid that here, I think:
+ if (low > (s32) (last - hyst))
+ low = last - hyst;
+ if (high < (s32) (last + hyst))
+ high = last + hyst;
but it's not clear to me that this is effective?
Let's see. last is -52, so low will be -60 and high will be -50.
Let's say hyst is 3 since I chose the ranges so closely. I'm guessing a
higher hysteresis and larger ranges would actually be better, but let's
stick to this for the sake of the example.
last-hyst = -55, so low isn't > that, low = -60
last+hyst = -49, so high = -49
but now it still fluctuates around -50, so if I next hit -48 you do the
same dance again with -50/-40, getting -51/-40 and never really
applying a full hysteresis, no?
I'll probably see an intermediate value of -50 at some point, but I'll
never actually *report* it, so "last" can switch between -48 and -52
constantly in this scenario, no?
I think it would make sense to unconditionally apply the hysteresis to
low/high, i.e. always set
low = low - hyst
high = high + hyst
so that you get "sticky" ranges once you're in them?
> + if (!wiphy_ext_feature_isset(&rdev->wiphy,
> +
> NL80211_EXT_FEATURE_CQM_RSSI_LIST))
> + return
> -EOPNOTSUPP;
That check should be earlier in the function
cfg80211_cqm_rssi_update(), no?
johannes
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-02-08 9:58 ` Johannes Berg
@ 2017-02-08 11:26 ` Andrew Zaborowski
2017-02-08 12:32 ` Johannes Berg
0 siblings, 1 reply; 12+ messages in thread
From: Andrew Zaborowski @ 2017-02-08 11:26 UTC (permalink / raw)
To: Johannes Berg; +Cc: linux-wireless
Hi,
On 8 February 2017 at 10:58, Johannes Berg <johannes@sipsolutions.net> wrote:
>
>> This method doesn't have a hysteresis parameter because there's no
>> benefit to the cfg80211 code from having the hysteresis be handled by
>> hardware/driver in terms of the number of wakeups. At the same time
>> it would likely be less consistent between drivers if offloaded or
>> done in the drivers.
>
> I'm not really sure I buy this.
>
> What if I configure a few ranges, and let's say one of the boundaries
> is -50dBm. Now if I sit just on that value of -50dBm and thus my signal
> fluctuates say -48..-52, I'd have to continuously wake up the host.
>
> You try to avoid that here, I think:
>
> + if (low > (s32) (last - hyst))
> + low = last - hyst;
> + if (high < (s32) (last + hyst))
> + high = last + hyst;
>
> but it's not clear to me that this is effective?
>
> Let's see. last is -52, so low will be -60 and high will be -50.
>
> Let's say hyst is 3 since I chose the ranges so closely. I'm guessing a
> higher hysteresis and larger ranges would actually be better, but let's
> stick to this for the sake of the example.
>
> last-hyst = -55, so low isn't > that, low = -60
> last+hyst = -49, so high = -49
>
> but now it still fluctuates around -50, so if I next hit -48 you do the
> same dance again with -50/-40, getting -51/-40 and never really
> applying a full hysteresis, no?
>
> I'll probably see an intermediate value of -50 at some point, but I'll
> never actually *report* it, so "last" can switch between -48 and -52
> constantly in this scenario, no?
Yes, sounds like this could happen.
>
>
> I think it would make sense to unconditionally apply the hysteresis to
> low/high, i.e. always set
> low = low - hyst
> high = high + hyst
>
> so that you get "sticky" ranges once you're in them?
Yes, maybe that's better, I guess I want to avoid just adding a lag /
delay in reporting changes that are not due to measurement error or
temporary. Could also do something in between, e.g. use "low - hyst"
if signal is close to low, otherwise just "low".
The question is how the current hysteresis parameter is defined, what
is expected of the firmware and how do driver authors decide whether
their firmware/hardware implements the same mechanism as expected by
the kernel. Would the same thing happen with firmware implementations
if the hysteresis value is 3 and the rssi fluctuates by +/- 2? Or
would it have to be +/- 3 or +/- 4 before this starts to happen. (If
this isn't well specified then it makes more sense to try to do it in
one place for consistency.)
>
>
>
>> + if (!wiphy_ext_feature_isset(&rdev->wiphy,
>> +
>> NL80211_EXT_FEATURE_CQM_RSSI_LIST))
>> + return
>> -EOPNOTSUPP;
>
>
> That check should be earlier in the function
> cfg80211_cqm_rssi_update(), no?
Oh looks like it can actually be removed in the current code because
nl80211_set_cqm_rssi already has this check and wdev->cqm_config can't
be set outside that function.
Best regards
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-02-08 11:26 ` Andrew Zaborowski
@ 2017-02-08 12:32 ` Johannes Berg
2017-02-10 9:39 ` Andrew Zaborowski
0 siblings, 1 reply; 12+ messages in thread
From: Johannes Berg @ 2017-02-08 12:32 UTC (permalink / raw)
To: Andrew Zaborowski; +Cc: linux-wireless
> > I think it would make sense to unconditionally apply the hysteresis
> > to low/high, i.e. always set
> > low = low - hyst
> > high = high + hyst
> >
> > so that you get "sticky" ranges once you're in them?
>
> Yes, maybe that's better, I guess I want to avoid just adding a lag /
> delay in reporting changes that are not due to measurement error or
> temporary. Could also do something in between, e.g. use "low - hyst"
> if signal is close to low, otherwise just "low".
That's sort of what you had, but except for the precise definition of
"close", no?
Actually, no, because you used "last - hyst" rather than "low - hyst"
it's different. I think we can live with checking if it's close, say
setting to "low - hyst" when it's within low + hyst - that avoids the
problem I outlined above and gets a bit more responsiveness, I guess.
> The question is how the current hysteresis parameter is defined, what
> is expected of the firmware and how do driver authors decide whether
> their firmware/hardware implements the same mechanism as expected by
> the kernel. Would the same thing happen with firmware
> implementations if the hysteresis value is 3 and the rssi fluctuates
> by +/- 2? Or would it have to be +/- 3 or +/- 4 before this starts
> to happen. (If this isn't well specified then it makes more sense to
> try to do it in one place for consistency.)
I'm not sure it's well-defined.
johannes
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-02-08 12:32 ` Johannes Berg
@ 2017-02-10 9:39 ` Andrew Zaborowski
2017-02-10 9:41 ` Johannes Berg
0 siblings, 1 reply; 12+ messages in thread
From: Andrew Zaborowski @ 2017-02-10 9:39 UTC (permalink / raw)
To: Johannes Berg; +Cc: linux-wireless
On 8 February 2017 at 13:32, Johannes Berg <johannes@sipsolutions.net> wrote:
>> > I think it would make sense to unconditionally apply the hysteresis
>> > to low/high, i.e. always set
>> > low = low - hyst
>> > high = high + hyst
>> >
>> > so that you get "sticky" ranges once you're in them?
>>
>> Yes, maybe that's better, I guess I want to avoid just adding a lag /
>> delay in reporting changes that are not due to measurement error or
>> temporary. Could also do something in between, e.g. use "low - hyst"
>> if signal is close to low, otherwise just "low".
>
> That's sort of what you had, but except for the precise definition of
> "close", no?
>
> Actually, no, because you used "last - hyst" rather than "low - hyst"
> it's different. I think we can live with checking if it's close, say
> setting to "low - hyst" when it's within low + hyst - that avoids the
> problem I outlined above and gets a bit more responsiveness, I guess.
I sent a version with this logic but came up with values that would
still cause the continous events as in your example, specifically with
a hyst of 3 and the reported RSSI values jumping between -51 and -47.
This could be avoided by changing operators between "less than" and
"less or equal" but I eventually sent a version with the "sticky"
ranges you suggested, I think that is just as good.
Best regards
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM
2017-02-10 9:39 ` Andrew Zaborowski
@ 2017-02-10 9:41 ` Johannes Berg
0 siblings, 0 replies; 12+ messages in thread
From: Johannes Berg @ 2017-02-10 9:41 UTC (permalink / raw)
To: Andrew Zaborowski; +Cc: linux-wireless
> I sent a version with this logic but came up with values that would
> still cause the continous events as in your example, specifically
> with a hyst of 3 and the reported RSSI values jumping between -51 and
> -47. This could be avoided by changing operators between "less than"
> and "less or equal" but I eventually sent a version with the "sticky"
> ranges you suggested, I think that is just as good.
Ah, I was just wondering why you'd sent a new version, hadn't checked
the difference yet :)
Thanks for the note.
johannes
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v4 4/5] mac80211: Add set_cqm_rssi_range_config
2017-01-25 11:43 [PATCH v4 1/5] mac80211: Pass new RSSI level in CQM RSSI notification Andrew Zaborowski
2017-01-25 11:43 ` [PATCH v4 2/5] cfg80211: " Andrew Zaborowski
2017-01-25 11:43 ` [PATCH v4 3/5] cfg80211: Accept multiple RSSI thresholds for CQM Andrew Zaborowski
@ 2017-01-25 11:43 ` Andrew Zaborowski
2017-01-25 11:43 ` [PATCH v4 5/5] wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple drivers Andrew Zaborowski
3 siblings, 0 replies; 12+ messages in thread
From: Andrew Zaborowski @ 2017-01-25 11:43 UTC (permalink / raw)
To: linux-wireless
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch as I don't have the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
---
changes in v3:
- set NL80211_EXT_FEATURE_CQM_RSSI_LIST automatically in
ieee80211_register_hw based on the default interface's
IEEE80211_VIF_BEACON_FILTER flag.
changes in v4:
- drop the above attempt and set NL80211_EXT_FEATURE_CQM_RSSI_LIST
in a separate patch in each driver.
---
include/net/mac80211.h | 6 ++++++
net/mac80211/cfg.c | 28 ++++++++++++++++++++++++++++
net/mac80211/mlme.c | 24 ++++++++++++++++++++++++
3 files changed, 58 insertions(+)
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 8810ae7..d3992c4 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -502,6 +502,10 @@ struct ieee80211_mu_group_data {
* implies disabled. As with the cfg80211 callback, a change here should
* cause an event to be sent indicating where the current value is in
* relation to the newly configured threshold.
+ * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
+ * implies disabled. This is an alternative mechanism to the single
+ * threshold event and can't be enabled simultaneously with it.
+ * @cqm_rssi_high: Connection quality monitor RSSI upper threshold.
* @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
* @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
* may filter ARP queries targeted for other addresses than listed here.
@@ -554,6 +558,8 @@ struct ieee80211_bss_conf {
u16 ht_operation_mode;
s32 cqm_rssi_thold;
u32 cqm_rssi_hyst;
+ s32 cqm_rssi_low;
+ s32 cqm_rssi_high;
struct cfg80211_chan_def chandef;
struct ieee80211_mu_group_data mu_group;
__be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index e91e503..cf02aaa 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -2630,6 +2630,33 @@ static int ieee80211_set_cqm_rssi_config(struct wiphy *wiphy,
bss_conf->cqm_rssi_thold = rssi_thold;
bss_conf->cqm_rssi_hyst = rssi_hyst;
+ bss_conf->cqm_rssi_low = 0;
+ bss_conf->cqm_rssi_high = 0;
+ sdata->u.mgd.last_cqm_event_signal = 0;
+
+ /* tell the driver upon association, unless already associated */
+ if (sdata->u.mgd.associated &&
+ sdata->vif.driver_flags & IEEE80211_VIF_SUPPORTS_CQM_RSSI)
+ ieee80211_bss_info_change_notify(sdata, BSS_CHANGED_CQM);
+
+ return 0;
+}
+
+static int ieee80211_set_cqm_rssi_range_config(struct wiphy *wiphy,
+ struct net_device *dev,
+ s32 rssi_low, s32 rssi_high)
+{
+ struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_vif *vif = &sdata->vif;
+ struct ieee80211_bss_conf *bss_conf = &vif->bss_conf;
+
+ if (sdata->vif.driver_flags & IEEE80211_VIF_BEACON_FILTER)
+ return -EOPNOTSUPP;
+
+ bss_conf->cqm_rssi_low = rssi_low;
+ bss_conf->cqm_rssi_high = rssi_high;
+ bss_conf->cqm_rssi_thold = 0;
+ bss_conf->cqm_rssi_hyst = 0;
sdata->u.mgd.last_cqm_event_signal = 0;
/* tell the driver upon association, unless already associated */
@@ -3628,6 +3655,7 @@ const struct cfg80211_ops mac80211_config_ops = {
.mgmt_tx = ieee80211_mgmt_tx,
.mgmt_tx_cancel_wait = ieee80211_mgmt_tx_cancel_wait,
.set_cqm_rssi_config = ieee80211_set_cqm_rssi_config,
+ .set_cqm_rssi_range_config = ieee80211_set_cqm_rssi_range_config,
.mgmt_frame_register = ieee80211_mgmt_frame_register,
.set_antenna = ieee80211_set_antenna,
.get_antenna = ieee80211_get_antenna,
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index 0cfa215..260e20d 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -3434,6 +3434,30 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_sub_if_data *sdata,
}
}
+ if (bss_conf->cqm_rssi_low &&
+ ifmgd->count_beacon_signal >= IEEE80211_SIGNAL_AVE_MIN_COUNT) {
+ int sig = -ewma_beacon_signal_read(&ifmgd->ave_beacon_signal);
+ int last_event = ifmgd->last_cqm_event_signal;
+ int low = bss_conf->cqm_rssi_low;
+ int high = bss_conf->cqm_rssi_high;
+
+ if (sig < low &&
+ (last_event == 0 || last_event >= low)) {
+ ifmgd->last_cqm_event_signal = sig;
+ ieee80211_cqm_rssi_notify(
+ &sdata->vif,
+ NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
+ sig, GFP_KERNEL);
+ } else if (sig > high &&
+ (last_event == 0 || last_event <= high)) {
+ ifmgd->last_cqm_event_signal = sig;
+ ieee80211_cqm_rssi_notify(
+ &sdata->vif,
+ NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
+ sig, GFP_KERNEL);
+ }
+ }
+
if (ifmgd->flags & IEEE80211_STA_CONNECTION_POLL) {
mlme_dbg_ratelimited(sdata,
"cancelling AP probe due to a received beacon\n");
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v4 5/5] wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple drivers
2017-01-25 11:43 [PATCH v4 1/5] mac80211: Pass new RSSI level in CQM RSSI notification Andrew Zaborowski
` (2 preceding siblings ...)
2017-01-25 11:43 ` [PATCH v4 4/5] mac80211: Add set_cqm_rssi_range_config Andrew Zaborowski
@ 2017-01-25 11:43 ` Andrew Zaborowski
2017-02-08 10:00 ` Johannes Berg
3 siblings, 1 reply; 12+ messages in thread
From: Andrew Zaborowski @ 2017-01-25 11:43 UTC (permalink / raw)
To: linux-wireless
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
---
drivers/net/wireless/admtek/adm8211.c | 2 ++
drivers/net/wireless/ath/ar5523/ar5523.c | 2 ++
drivers/net/wireless/ath/ath10k/mac.c | 2 ++
drivers/net/wireless/ath/ath5k/base.c | 2 ++
drivers/net/wireless/ath/ath9k/htc_drv_init.c | 2 ++
drivers/net/wireless/ath/ath9k/init.c | 2 ++
drivers/net/wireless/ath/carl9170/main.c | 2 ++
drivers/net/wireless/ath/wcn36xx/main.c | 3 +++
drivers/net/wireless/atmel/at76c50x-usb.c | 2 ++
drivers/net/wireless/broadcom/b43/main.c | 2 ++
drivers/net/wireless/broadcom/b43legacy/main.c | 2 ++
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c | 2 ++
drivers/net/wireless/intel/iwlegacy/3945-mac.c | 2 ++
drivers/net/wireless/intel/iwlegacy/4965-mac.c | 2 ++
drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c | 2 ++
drivers/net/wireless/mac80211_hwsim.c | 2 ++
drivers/net/wireless/marvell/libertas_tf/main.c | 2 ++
drivers/net/wireless/marvell/mwl8k.c | 2 ++
drivers/net/wireless/mediatek/mt7601u/init.c | 2 ++
drivers/net/wireless/ralink/rt2x00/rt2x00dev.c | 3 +++
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c | 2 ++
drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c | 2 ++
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c | 2 ++
drivers/net/wireless/rsi/rsi_91x_mac80211.c | 2 ++
drivers/net/wireless/zydas/zd1211rw/zd_mac.c | 2 ++
drivers/staging/vt6655/device_main.c | 2 ++
drivers/staging/vt6656/main_usb.c | 2 ++
27 files changed, 56 insertions(+)
diff --git a/drivers/net/wireless/admtek/adm8211.c b/drivers/net/wireless/admtek/adm8211.c
index 70ecd82..96362f0 100644
--- a/drivers/net/wireless/admtek/adm8211.c
+++ b/drivers/net/wireless/admtek/adm8211.c
@@ -1896,6 +1896,8 @@ static int adm8211_probe(struct pci_dev *pdev,
dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band;
+ wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
err = ieee80211_register_hw(dev);
if (err) {
printk(KERN_ERR "%s (adm8211): Cannot register device\n",
diff --git a/drivers/net/wireless/ath/ar5523/ar5523.c b/drivers/net/wireless/ath/ar5523/ar5523.c
index 7a60d2e..f2f4ccf 100644
--- a/drivers/net/wireless/ath/ar5523/ar5523.c
+++ b/drivers/net/wireless/ath/ar5523/ar5523.c
@@ -1689,6 +1689,8 @@ static int ar5523_probe(struct usb_interface *intf,
if (error)
goto out_cancel_rx_cmd;
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
usb_set_intfdata(intf, hw);
error = ieee80211_register_hw(hw);
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index aa545a1..fe7eab3 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -8146,6 +8146,8 @@ int ath10k_mac_register(struct ath10k *ar)
ar->hw->wiphy->cipher_suites = cipher_suites;
ar->hw->wiphy->n_cipher_suites = ARRAY_SIZE(cipher_suites);
+ wiphy_ext_feature_set(ar->hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(ar->hw);
if (ret) {
ath10k_err(ar, "failed to register ieee80211: %d\n", ret);
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index d98fd42..92ece64 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -2564,6 +2564,8 @@ ath5k_init_ah(struct ath5k_hw *ah, const struct ath_bus_ops *bus_ops)
hw->extra_tx_headroom = 2;
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
/*
* Mark the device as detached to avoid processing
* interrupts until setup is complete.
diff --git a/drivers/net/wireless/ath/ath9k/htc_drv_init.c b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
index b65c1b6..defacc6 100644
--- a/drivers/net/wireless/ath/ath9k/htc_drv_init.c
+++ b/drivers/net/wireless/ath/ath9k/htc_drv_init.c
@@ -780,6 +780,8 @@ static void ath9k_set_hw_capab(struct ath9k_htc_priv *priv,
}
SET_IEEE80211_PERM_ADDR(hw, common->macaddr);
+
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
}
static int ath9k_init_firmware_version(struct ath9k_htc_priv *priv)
diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index 2079466..6bacda1 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -951,6 +951,8 @@ static void ath9k_set_hw_capab(struct ath_softc *sc, struct ieee80211_hw *hw)
ath9k_cmn_reload_chainmask(ah);
SET_IEEE80211_PERM_ADDR(hw, common->macaddr);
+
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
}
int ath9k_init_device(u16 devid, struct ath_softc *sc,
diff --git a/drivers/net/wireless/ath/carl9170/main.c b/drivers/net/wireless/ath/carl9170/main.c
index ffb22a0..988c885 100644
--- a/drivers/net/wireless/ath/carl9170/main.c
+++ b/drivers/net/wireless/ath/carl9170/main.c
@@ -1874,6 +1874,8 @@ void *carl9170_alloc(size_t priv_size)
for (i = 0; i < ARRAY_SIZE(ar->noise); i++)
ar->noise[i] = -95; /* ATH_DEFAULT_NOISE_FLOOR */
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
return ar;
err_nomem:
diff --git a/drivers/net/wireless/ath/wcn36xx/main.c b/drivers/net/wireless/ath/wcn36xx/main.c
index e1d59da..1b6c173 100644
--- a/drivers/net/wireless/ath/wcn36xx/main.c
+++ b/drivers/net/wireless/ath/wcn36xx/main.c
@@ -1046,6 +1046,9 @@ static int wcn36xx_init_ieee80211(struct wcn36xx *wcn)
wcn->hw->sta_data_size = sizeof(struct wcn36xx_sta);
wcn->hw->vif_data_size = sizeof(struct wcn36xx_vif);
+ wiphy_ext_feature_set(wcn->hw->wiphy,
+ NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
return ret;
}
diff --git a/drivers/net/wireless/atmel/at76c50x-usb.c b/drivers/net/wireless/atmel/at76c50x-usb.c
index 0e18067..09defbc 100644
--- a/drivers/net/wireless/atmel/at76c50x-usb.c
+++ b/drivers/net/wireless/atmel/at76c50x-usb.c
@@ -2377,6 +2377,8 @@ static int at76_init_new_device(struct at76_priv *priv,
wiphy->hw_version = priv->board_type;
+ wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(priv->hw);
if (ret) {
printk(KERN_ERR "cannot register mac80211 hw (status %d)!\n",
diff --git a/drivers/net/wireless/broadcom/b43/main.c b/drivers/net/wireless/broadcom/b43/main.c
index 52f3541..d23aac7 100644
--- a/drivers/net/wireless/broadcom/b43/main.c
+++ b/drivers/net/wireless/broadcom/b43/main.c
@@ -5598,6 +5598,8 @@ static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev)
hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
wl->hw_registred = false;
hw->max_rates = 2;
SET_IEEE80211_DEV(hw, dev->dev);
diff --git a/drivers/net/wireless/broadcom/b43legacy/main.c b/drivers/net/wireless/broadcom/b43legacy/main.c
index e97ab2b..44781b8 100644
--- a/drivers/net/wireless/broadcom/b43legacy/main.c
+++ b/drivers/net/wireless/broadcom/b43legacy/main.c
@@ -3850,6 +3850,8 @@ static int b43legacy_wireless_init(struct ssb_device *dev)
else
SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
/* Get and initialize struct b43legacy_wl */
wl = hw_to_b43legacy_wl(hw);
memset(wl, 0, sizeof(*wl));
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c b/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c
index 7c2a9a9..ddfdfe1 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c
@@ -1082,6 +1082,8 @@ static int ieee_hw_init(struct ieee80211_hw *hw)
* hw->wiphy->flags |= WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD;
*/
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
hw->rate_control_algorithm = "minstrel_ht";
hw->sta_data_size = 0;
diff --git a/drivers/net/wireless/intel/iwlegacy/3945-mac.c b/drivers/net/wireless/intel/iwlegacy/3945-mac.c
index 466912e..ebd74f7 100644
--- a/drivers/net/wireless/intel/iwlegacy/3945-mac.c
+++ b/drivers/net/wireless/intel/iwlegacy/3945-mac.c
@@ -3592,6 +3592,8 @@ il3945_setup_mac(struct il_priv *il)
il_leds_init(il);
+ wiphy_ext_feature_set(il->hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(il->hw);
if (ret) {
IL_ERR("Failed to register hw (error %d)\n", ret);
diff --git a/drivers/net/wireless/intel/iwlegacy/4965-mac.c b/drivers/net/wireless/intel/iwlegacy/4965-mac.c
index a91d170..54ecda5 100644
--- a/drivers/net/wireless/intel/iwlegacy/4965-mac.c
+++ b/drivers/net/wireless/intel/iwlegacy/4965-mac.c
@@ -5799,6 +5799,8 @@ il4965_mac_setup_register(struct il_priv *il, u32 max_probe_length)
il_leds_init(il);
+ wiphy_ext_feature_set(il->hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(il->hw);
if (ret) {
IL_ERR("Failed to register hw (error %d)\n", ret);
diff --git a/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c b/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c
index 8c07194..2b23c3f 100644
--- a/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c
+++ b/drivers/net/wireless/intel/iwlwifi/dvm/mac80211.c
@@ -213,6 +213,8 @@ int iwlagn_mac_setup_register(struct iwl_priv *priv,
iwl_leds_init(priv);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(priv->hw);
if (ret) {
IWL_ERR(priv, "Failed to register hw (error %d)\n", ret);
diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c
index 1620a5d..0150747 100644
--- a/drivers/net/wireless/mac80211_hwsim.c
+++ b/drivers/net/wireless/mac80211_hwsim.c
@@ -2645,6 +2645,8 @@ static int mac80211_hwsim_new_radio(struct genl_info *info,
if (param->no_vif)
ieee80211_hw_set(hw, NO_AUTO_VIF);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
err = ieee80211_register_hw(hw);
if (err < 0) {
printk(KERN_DEBUG "mac80211_hwsim: ieee80211_register_hw failed (%d)\n",
diff --git a/drivers/net/wireless/marvell/libertas_tf/main.c b/drivers/net/wireless/marvell/libertas_tf/main.c
index 54e426c..d803331 100644
--- a/drivers/net/wireless/marvell/libertas_tf/main.c
+++ b/drivers/net/wireless/marvell/libertas_tf/main.c
@@ -641,6 +641,8 @@ struct lbtf_private *lbtf_add_card(void *card, struct device *dmdev)
BIT(NL80211_IFTYPE_ADHOC);
skb_queue_head_init(&priv->bc_ps_buf);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
SET_IEEE80211_DEV(hw, dmdev);
INIT_WORK(&priv->cmd_work, lbtf_cmd_work);
diff --git a/drivers/net/wireless/marvell/mwl8k.c b/drivers/net/wireless/marvell/mwl8k.c
index b1b400b..c295a4c 100644
--- a/drivers/net/wireless/marvell/mwl8k.c
+++ b/drivers/net/wireless/marvell/mwl8k.c
@@ -6144,6 +6144,8 @@ static int mwl8k_firmware_load_success(struct mwl8k_priv *priv)
if (priv->sta_macids_supported || priv->device_info->fw_image_sta)
hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_STATION);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
rc = ieee80211_register_hw(hw);
if (rc) {
wiphy_err(hw->wiphy, "Cannot register device\n");
diff --git a/drivers/net/wireless/mediatek/mt7601u/init.c b/drivers/net/wireless/mediatek/mt7601u/init.c
index a6e9017..d3b611a 100644
--- a/drivers/net/wireless/mediatek/mt7601u/init.c
+++ b/drivers/net/wireless/mediatek/mt7601u/init.c
@@ -615,6 +615,8 @@ int mt7601u_register_device(struct mt7601u_dev *dev)
wiphy->features |= NL80211_FEATURE_ACTIVE_MONITOR;
wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
+ wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = mt76_init_sband_2g(dev);
if (ret)
return ret;
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
index eb7b714..139bb51 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
@@ -1389,6 +1389,9 @@ int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev)
rt2x00dev->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
+ wiphy_ext_feature_set(rt2x00dev->hw->wiphy,
+ NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
/*
* Initialize ieee80211 structure.
*/
diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c
index e895a84..e387dec 100644
--- a/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c
+++ b/drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c
@@ -1877,6 +1877,8 @@ static int rtl8180_probe(struct pci_dev *pdev,
else
ieee80211_hw_set(dev, SIGNAL_UNSPEC);
+ wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
rtl8180_eeprom_read(priv);
switch (priv->rf_type) {
diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c b/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
index 231f84d..274ad6d 100644
--- a/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
+++ b/drivers/net/wireless/realtek/rtl818x/rtl8187/dev.c
@@ -1609,6 +1609,8 @@ static int rtl8187_probe(struct usb_interface *intf,
dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
BIT(NL80211_IFTYPE_ADHOC) ;
+ wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
" info!\n");
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
index 3a86675..75fbb39 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
@@ -6134,6 +6134,8 @@ static int rtl8xxxu_probe(struct usb_interface *interface,
ieee80211_hw_set(hw, HAS_RATE_CONTROL);
ieee80211_hw_set(hw, AMPDU_AGGREGATION);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ret = ieee80211_register_hw(priv->hw);
if (ret) {
dev_err(&udev->dev, "%s: Failed to register: %i\n",
diff --git a/drivers/net/wireless/rsi/rsi_91x_mac80211.c b/drivers/net/wireless/rsi/rsi_91x_mac80211.c
index e321647..021e5ac 100644
--- a/drivers/net/wireless/rsi/rsi_91x_mac80211.c
+++ b/drivers/net/wireless/rsi/rsi_91x_mac80211.c
@@ -1261,6 +1261,8 @@ int rsi_mac80211_attach(struct rsi_common *common)
wiphy->reg_notifier = rsi_reg_notify;
+ wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
status = ieee80211_register_hw(hw);
if (status)
return status;
diff --git a/drivers/net/wireless/zydas/zd1211rw/zd_mac.c b/drivers/net/wireless/zydas/zd1211rw/zd_mac.c
index 3e37a04..fe6517a 100644
--- a/drivers/net/wireless/zydas/zd1211rw/zd_mac.c
+++ b/drivers/net/wireless/zydas/zd1211rw/zd_mac.c
@@ -1408,6 +1408,8 @@ struct ieee80211_hw *zd_mac_alloc_hw(struct usb_interface *intf)
BIT(NL80211_IFTYPE_ADHOC) |
BIT(NL80211_IFTYPE_AP);
+ wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
hw->max_signal = 100;
hw->queues = 1;
hw->extra_tx_headroom = sizeof(struct zd_ctrlset);
diff --git a/drivers/staging/vt6655/device_main.c b/drivers/staging/vt6655/device_main.c
index da0f711..7f18f70 100644
--- a/drivers/staging/vt6655/device_main.c
+++ b/drivers/staging/vt6655/device_main.c
@@ -1661,6 +1661,8 @@ vt6655_probe(struct pci_dev *pcid, const struct pci_device_id *ent)
wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
BIT(NL80211_IFTYPE_ADHOC) | BIT(NL80211_IFTYPE_AP);
+ wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ieee80211_hw_set(priv->hw, TIMING_BEACON_ONLY);
ieee80211_hw_set(priv->hw, SIGNAL_DBM);
ieee80211_hw_set(priv->hw, RX_INCLUDES_FCS);
diff --git a/drivers/staging/vt6656/main_usb.c b/drivers/staging/vt6656/main_usb.c
index 50d02d9..80b5c73 100644
--- a/drivers/staging/vt6656/main_usb.c
+++ b/drivers/staging/vt6656/main_usb.c
@@ -986,6 +986,8 @@ vt6656_probe(struct usb_interface *intf, const struct usb_device_id *id)
wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
BIT(NL80211_IFTYPE_ADHOC) | BIT(NL80211_IFTYPE_AP);
+ wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
+
ieee80211_hw_set(priv->hw, TIMING_BEACON_ONLY);
ieee80211_hw_set(priv->hw, SIGNAL_DBM);
ieee80211_hw_set(priv->hw, RX_INCLUDES_FCS);
--
2.9.3
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v4 5/5] wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple drivers
2017-01-25 11:43 ` [PATCH v4 5/5] wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple drivers Andrew Zaborowski
@ 2017-02-08 10:00 ` Johannes Berg
0 siblings, 0 replies; 12+ messages in thread
From: Johannes Berg @ 2017-02-08 10:00 UTC (permalink / raw)
To: Andrew Zaborowski, linux-wireless
On Wed, 2017-01-25 at 12:43 +0100, Andrew Zaborowski wrote:
> Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
> wholesale in all mac80211-based drivers that do not set the
> IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
> be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
> will detect when the thresholds set by
> ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
> drivers need code to enable the firmware to monitor the thresholds.
> This is mostly only compile-tested.
4 and 5 look fine, but obviously depend on 3.
johannes
^ permalink raw reply [flat|nested] 12+ messages in thread