* [PATCH net-next v5 0/4] net: dsa: Support for pdata in dsa2
@ 2017-02-04 21:02 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: linux-arm-kernel
Hi all,
This is not exactly new, and was sent before, although back then, I did not
have an user of the pre-declared MDIO board information, but now we do. Note
that I have additional changes queued up to have b53 register platform data for
MIPS bcm47xx and bcm63xx.
Yes I know that we should have the Orion platforms eventually be converted to
Device Tree, but until that happens, I don't want any remaining users of the
old "dsa" platform device (hence the previous DTS submissions for ARM/mvebu)
and, there will be platforms out there that most likely won't never see DT
coming their way (BCM47xx is almost 100% sure, BCM63xx maybe not in a distant
future).
We would probably want the whole series to be merged via David Miller's tree
to simplify things.
Thanks!
Changes in v5:
- dropped changes to drivers/base/ because after more than a month, we cannot
get any answer from Greg KH
- rebased against latest net-next/master
Changes in v4:
- Changed device_find_class() to device_find_in_class_name()
- Added kerneldoc above device_find_in_class_name() to explain what it does
and the calling convention regarding device reference counts
- Changed dev_to_net_device to device_to_net_device() added comments
about what it does and the caller conventions regarding reference counts
Changes in v3:
- Tested EPROBE_DEFER from a mockup MDIO/DSA switch driver and everything
is fine, once the driver finally probes we have access to platform data
as expected
- added comment above dsa_port_is_valid() that port->name is mandatory
for platform data cases
- added an extra check in dsa_parse_member() for a NULL pdata pointer
- fixed a bunch of checkpatch errors and warnings
Changes in v2:
- Rebased against latest net-next/master
- Moved dev_find_class() to device_find_class() into drivers/base/core.c
- Moved dev_to_net_device into net/core/dev.c
- Utilize dsa_chip_data directly instead of dsa_platform_data
- Augmented dsa_chip_data to be multi-CPU port ready
Changes from last submission (few months back):
- rebased against latest net-next
- do not introduce dsa2_platform_data which was overkill and was meant to
allow us to do exaclty the same things with platform data and Device Tree
we use the existing dsa_platform_data instead
- properly register MDIO devices when the MDIO bus is registered and associate
platform_data with them
- add a change to the Orion platform code to demonstrate how this can be used
Thank you
Florian Fainelli (4):
net: dsa: Rename and export dev_to_net_device()
net: dsa: Add support for platform data
net: phy: Allow pre-declaration of MDIO devices
ARM: orion: Register DSA switch as a MDIO device
arch/arm/mach-orion5x/common.c | 2 +-
arch/arm/mach-orion5x/common.h | 4 +-
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 7 +-
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 7 +-
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 7 +-
arch/arm/mach-orion5x/wnr854t-setup.c | 2 +-
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 7 +-
arch/arm/plat-orion/common.c | 25 +++++--
arch/arm/plat-orion/include/plat/common.h | 4 +-
drivers/net/phy/Makefile | 3 +-
drivers/net/phy/mdio-boardinfo.c | 86 ++++++++++++++++++++++
drivers/net/phy/mdio-boardinfo.h | 19 +++++
drivers/net/phy/mdio_bus.c | 4 ++
drivers/net/phy/mdio_device.c | 11 +++
include/linux/mdio.h | 3 +
include/linux/mod_devicetable.h | 1 +
include/linux/phy.h | 19 +++++
include/net/dsa.h | 7 ++
net/dsa/dsa.c | 5 +-
net/dsa/dsa2.c | 102 ++++++++++++++++++++++-----
20 files changed, 268 insertions(+), 57 deletions(-)
create mode 100644 drivers/net/phy/mdio-boardinfo.c
create mode 100644 drivers/net/phy/mdio-boardinfo.h
--
2.9.3
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH net-next v5 1/4] net: dsa: Rename and export dev_to_net_device()
2017-02-04 21:02 ` Florian Fainelli
@ 2017-02-04 21:02 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Jason Cooper, Andrew Lunn,
Sebastian Hesselbarth, Gregory Clement, Russell King,
Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
include/net/dsa.h | 1 +
net/dsa/dsa.c | 5 +++--
2 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 2cb77e64d648..4327b0b03293 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -428,6 +428,7 @@ struct dsa_switch_driver {
void register_switch_driver(struct dsa_switch_driver *type);
void unregister_switch_driver(struct dsa_switch_driver *type);
struct mii_bus *dsa_host_dev_to_mii_bus(struct device *dev);
+struct net_device *dsa_dev_to_net_device(struct device *dev);
static inline bool dsa_uses_tagged_protocol(struct dsa_switch_tree *dst)
{
diff --git a/net/dsa/dsa.c b/net/dsa/dsa.c
index 619e57a44d1d..5a5f79bbda6f 100644
--- a/net/dsa/dsa.c
+++ b/net/dsa/dsa.c
@@ -486,7 +486,7 @@ struct mii_bus *dsa_host_dev_to_mii_bus(struct device *dev)
}
EXPORT_SYMBOL_GPL(dsa_host_dev_to_mii_bus);
-static struct net_device *dev_to_net_device(struct device *dev)
+struct net_device *dsa_dev_to_net_device(struct device *dev)
{
struct device *d;
@@ -503,6 +503,7 @@ static struct net_device *dev_to_net_device(struct device *dev)
return NULL;
}
+EXPORT_SYMBOL_GPL(dsa_dev_to_net_device);
#ifdef CONFIG_OF
static int dsa_of_setup_routing_table(struct dsa_platform_data *pd,
@@ -811,7 +812,7 @@ static int dsa_probe(struct platform_device *pdev)
dev = pd->of_netdev;
dev_hold(dev);
} else {
- dev = dev_to_net_device(pd->netdev);
+ dev = dsa_dev_to_net_device(pd->netdev);
}
if (dev == NULL) {
ret = -EPROBE_DEFER;
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH net-next v5 1/4] net: dsa: Rename and export dev_to_net_device()
@ 2017-02-04 21:02 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: linux-arm-kernel
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
include/net/dsa.h | 1 +
net/dsa/dsa.c | 5 +++--
2 files changed, 4 insertions(+), 2 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 2cb77e64d648..4327b0b03293 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -428,6 +428,7 @@ struct dsa_switch_driver {
void register_switch_driver(struct dsa_switch_driver *type);
void unregister_switch_driver(struct dsa_switch_driver *type);
struct mii_bus *dsa_host_dev_to_mii_bus(struct device *dev);
+struct net_device *dsa_dev_to_net_device(struct device *dev);
static inline bool dsa_uses_tagged_protocol(struct dsa_switch_tree *dst)
{
diff --git a/net/dsa/dsa.c b/net/dsa/dsa.c
index 619e57a44d1d..5a5f79bbda6f 100644
--- a/net/dsa/dsa.c
+++ b/net/dsa/dsa.c
@@ -486,7 +486,7 @@ struct mii_bus *dsa_host_dev_to_mii_bus(struct device *dev)
}
EXPORT_SYMBOL_GPL(dsa_host_dev_to_mii_bus);
-static struct net_device *dev_to_net_device(struct device *dev)
+struct net_device *dsa_dev_to_net_device(struct device *dev)
{
struct device *d;
@@ -503,6 +503,7 @@ static struct net_device *dev_to_net_device(struct device *dev)
return NULL;
}
+EXPORT_SYMBOL_GPL(dsa_dev_to_net_device);
#ifdef CONFIG_OF
static int dsa_of_setup_routing_table(struct dsa_platform_data *pd,
@@ -811,7 +812,7 @@ static int dsa_probe(struct platform_device *pdev)
dev = pd->of_netdev;
dev_hold(dev);
} else {
- dev = dev_to_net_device(pd->netdev);
+ dev = dsa_dev_to_net_device(pd->netdev);
}
if (dev == NULL) {
ret = -EPROBE_DEFER;
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH net-next v5 2/4] net: dsa: Add support for platform data
2017-02-04 21:02 ` Florian Fainelli
@ 2017-02-04 21:02 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Jason Cooper, Andrew Lunn,
Sebastian Hesselbarth, Gregory Clement, Russell King,
Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
include/net/dsa.h | 6 ++++
net/dsa/dsa2.c | 102 ++++++++++++++++++++++++++++++++++++++++++++----------
2 files changed, 90 insertions(+), 18 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 4327b0b03293..4449f22c64ba 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -44,6 +44,11 @@ struct dsa_chip_data {
struct device *host_dev;
int sw_addr;
+ /*
+ * Reference to network devices
+ */
+ struct device *netdev[DSA_MAX_PORTS];
+
/* set to size of eeprom if supported by the switch */
int eeprom_len;
@@ -166,6 +171,7 @@ struct dsa_mall_tc_entry {
struct dsa_port {
struct dsa_switch *ds;
unsigned int index;
+ const char *name;
struct net_device *netdev;
struct device_node *dn;
unsigned int ageing_time;
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 9f8cc26be9ea..3a7631f63638 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -78,19 +78,28 @@ static void dsa_dst_del_ds(struct dsa_switch_tree *dst,
kref_put(&dst->refcount, dsa_free_dst);
}
+/* For platform data configurations, we need to have a valid name argument to
+ * differentiate a disabled port from an enabled one
+ */
static bool dsa_port_is_valid(struct dsa_port *port)
{
- return !!port->dn;
+ return !!(port->dn || port->name);
}
static bool dsa_port_is_dsa(struct dsa_port *port)
{
- return !!of_parse_phandle(port->dn, "link", 0);
+ if (port->name && !strcmp(port->name, "dsa"))
+ return true;
+ else
+ return !!of_parse_phandle(port->dn, "link", 0);
}
static bool dsa_port_is_cpu(struct dsa_port *port)
{
- return !!of_parse_phandle(port->dn, "ethernet", 0);
+ if (port->name && !strcmp(port->name, "cpu"))
+ return true;
+ else
+ return !!of_parse_phandle(port->dn, "ethernet", 0);
}
static bool dsa_ds_find_port_dn(struct dsa_switch *ds,
@@ -250,10 +259,11 @@ static void dsa_cpu_port_unapply(struct dsa_port *port, u32 index,
static int dsa_user_port_apply(struct dsa_port *port, u32 index,
struct dsa_switch *ds)
{
- const char *name;
+ const char *name = port->name;
int err;
- name = of_get_property(port->dn, "label", NULL);
+ if (port->dn)
+ name = of_get_property(port->dn, "label", NULL);
if (!name)
name = "eth%d";
@@ -438,11 +448,16 @@ static int dsa_cpu_parse(struct dsa_port *port, u32 index,
struct net_device *ethernet_dev;
struct device_node *ethernet;
- ethernet = of_parse_phandle(port->dn, "ethernet", 0);
- if (!ethernet)
- return -EINVAL;
+ if (port->dn) {
+ ethernet = of_parse_phandle(port->dn, "ethernet", 0);
+ if (!ethernet)
+ return -EINVAL;
+ ethernet_dev = of_find_net_device_by_node(ethernet);
+ } else {
+ ethernet_dev = dsa_dev_to_net_device(ds->cd->netdev[index]);
+ dev_put(ethernet_dev);
+ }
- ethernet_dev = of_find_net_device_by_node(ethernet);
if (!ethernet_dev)
return -EPROBE_DEFER;
@@ -545,6 +560,33 @@ static int dsa_parse_ports_dn(struct device_node *ports, struct dsa_switch *ds)
return 0;
}
+static int dsa_parse_ports(struct dsa_chip_data *cd, struct dsa_switch *ds)
+{
+ bool valid_name_found = false;
+ unsigned int i;
+
+ for (i = 0; i < DSA_MAX_PORTS; i++) {
+ if (!cd->port_names[i])
+ continue;
+
+ ds->ports[i].name = cd->port_names[i];
+
+ /* Initialize enabled_port_mask now for drv->setup()
+ * to have access to a correct value, just like what
+ * net/dsa/dsa.c::dsa_switch_setup_one does.
+ */
+ if (!dsa_port_is_cpu(&ds->ports[i]))
+ ds->enabled_port_mask |= 1 << i;
+
+ valid_name_found = true;
+ }
+
+ if (!valid_name_found && i == DSA_MAX_PORTS)
+ return -EINVAL;
+
+ return 0;
+}
+
static int dsa_parse_member_dn(struct device_node *np, u32 *tree, u32 *index)
{
int err;
@@ -569,6 +611,18 @@ static int dsa_parse_member_dn(struct device_node *np, u32 *tree, u32 *index)
return 0;
}
+static int dsa_parse_member(struct dsa_chip_data *pd, u32 *tree, u32 *index)
+{
+ if (!pd)
+ return -ENODEV;
+
+ /* We do not support complex trees with dsa_chip_data */
+ *tree = 0;
+ *index = 0;
+
+ return 0;
+}
+
static struct device_node *dsa_get_ports(struct dsa_switch *ds,
struct device_node *np)
{
@@ -585,23 +639,34 @@ static struct device_node *dsa_get_ports(struct dsa_switch *ds,
static int _dsa_register_switch(struct dsa_switch *ds, struct device *dev)
{
+ struct dsa_chip_data *pdata = dev->platform_data;
struct device_node *np = dev->of_node;
struct dsa_switch_tree *dst;
struct device_node *ports;
u32 tree, index;
int i, err;
- err = dsa_parse_member_dn(np, &tree, &index);
- if (err)
- return err;
+ if (np) {
+ err = dsa_parse_member_dn(np, &tree, &index);
+ if (err)
+ return err;
- ports = dsa_get_ports(ds, np);
- if (IS_ERR(ports))
- return PTR_ERR(ports);
+ ports = dsa_get_ports(ds, np);
+ if (IS_ERR(ports))
+ return PTR_ERR(ports);
- err = dsa_parse_ports_dn(ports, ds);
- if (err)
- return err;
+ err = dsa_parse_ports_dn(ports, ds);
+ if (err)
+ return err;
+ } else {
+ err = dsa_parse_member(pdata, &tree, &index);
+ if (err)
+ return err;
+
+ err = dsa_parse_ports(pdata, ds);
+ if (err)
+ return err;
+ }
dst = dsa_get_dst(tree);
if (!dst) {
@@ -617,6 +682,7 @@ static int _dsa_register_switch(struct dsa_switch *ds, struct device *dev)
ds->dst = dst;
ds->index = index;
+ ds->cd = pdata;
/* Initialize the routing table */
for (i = 0; i < DSA_MAX_SWITCHES; ++i)
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH net-next v5 2/4] net: dsa: Add support for platform data
@ 2017-02-04 21:02 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: linux-arm-kernel
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
include/net/dsa.h | 6 ++++
net/dsa/dsa2.c | 102 ++++++++++++++++++++++++++++++++++++++++++++----------
2 files changed, 90 insertions(+), 18 deletions(-)
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 4327b0b03293..4449f22c64ba 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -44,6 +44,11 @@ struct dsa_chip_data {
struct device *host_dev;
int sw_addr;
+ /*
+ * Reference to network devices
+ */
+ struct device *netdev[DSA_MAX_PORTS];
+
/* set to size of eeprom if supported by the switch */
int eeprom_len;
@@ -166,6 +171,7 @@ struct dsa_mall_tc_entry {
struct dsa_port {
struct dsa_switch *ds;
unsigned int index;
+ const char *name;
struct net_device *netdev;
struct device_node *dn;
unsigned int ageing_time;
diff --git a/net/dsa/dsa2.c b/net/dsa/dsa2.c
index 9f8cc26be9ea..3a7631f63638 100644
--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -78,19 +78,28 @@ static void dsa_dst_del_ds(struct dsa_switch_tree *dst,
kref_put(&dst->refcount, dsa_free_dst);
}
+/* For platform data configurations, we need to have a valid name argument to
+ * differentiate a disabled port from an enabled one
+ */
static bool dsa_port_is_valid(struct dsa_port *port)
{
- return !!port->dn;
+ return !!(port->dn || port->name);
}
static bool dsa_port_is_dsa(struct dsa_port *port)
{
- return !!of_parse_phandle(port->dn, "link", 0);
+ if (port->name && !strcmp(port->name, "dsa"))
+ return true;
+ else
+ return !!of_parse_phandle(port->dn, "link", 0);
}
static bool dsa_port_is_cpu(struct dsa_port *port)
{
- return !!of_parse_phandle(port->dn, "ethernet", 0);
+ if (port->name && !strcmp(port->name, "cpu"))
+ return true;
+ else
+ return !!of_parse_phandle(port->dn, "ethernet", 0);
}
static bool dsa_ds_find_port_dn(struct dsa_switch *ds,
@@ -250,10 +259,11 @@ static void dsa_cpu_port_unapply(struct dsa_port *port, u32 index,
static int dsa_user_port_apply(struct dsa_port *port, u32 index,
struct dsa_switch *ds)
{
- const char *name;
+ const char *name = port->name;
int err;
- name = of_get_property(port->dn, "label", NULL);
+ if (port->dn)
+ name = of_get_property(port->dn, "label", NULL);
if (!name)
name = "eth%d";
@@ -438,11 +448,16 @@ static int dsa_cpu_parse(struct dsa_port *port, u32 index,
struct net_device *ethernet_dev;
struct device_node *ethernet;
- ethernet = of_parse_phandle(port->dn, "ethernet", 0);
- if (!ethernet)
- return -EINVAL;
+ if (port->dn) {
+ ethernet = of_parse_phandle(port->dn, "ethernet", 0);
+ if (!ethernet)
+ return -EINVAL;
+ ethernet_dev = of_find_net_device_by_node(ethernet);
+ } else {
+ ethernet_dev = dsa_dev_to_net_device(ds->cd->netdev[index]);
+ dev_put(ethernet_dev);
+ }
- ethernet_dev = of_find_net_device_by_node(ethernet);
if (!ethernet_dev)
return -EPROBE_DEFER;
@@ -545,6 +560,33 @@ static int dsa_parse_ports_dn(struct device_node *ports, struct dsa_switch *ds)
return 0;
}
+static int dsa_parse_ports(struct dsa_chip_data *cd, struct dsa_switch *ds)
+{
+ bool valid_name_found = false;
+ unsigned int i;
+
+ for (i = 0; i < DSA_MAX_PORTS; i++) {
+ if (!cd->port_names[i])
+ continue;
+
+ ds->ports[i].name = cd->port_names[i];
+
+ /* Initialize enabled_port_mask now for drv->setup()
+ * to have access to a correct value, just like what
+ * net/dsa/dsa.c::dsa_switch_setup_one does.
+ */
+ if (!dsa_port_is_cpu(&ds->ports[i]))
+ ds->enabled_port_mask |= 1 << i;
+
+ valid_name_found = true;
+ }
+
+ if (!valid_name_found && i == DSA_MAX_PORTS)
+ return -EINVAL;
+
+ return 0;
+}
+
static int dsa_parse_member_dn(struct device_node *np, u32 *tree, u32 *index)
{
int err;
@@ -569,6 +611,18 @@ static int dsa_parse_member_dn(struct device_node *np, u32 *tree, u32 *index)
return 0;
}
+static int dsa_parse_member(struct dsa_chip_data *pd, u32 *tree, u32 *index)
+{
+ if (!pd)
+ return -ENODEV;
+
+ /* We do not support complex trees with dsa_chip_data */
+ *tree = 0;
+ *index = 0;
+
+ return 0;
+}
+
static struct device_node *dsa_get_ports(struct dsa_switch *ds,
struct device_node *np)
{
@@ -585,23 +639,34 @@ static struct device_node *dsa_get_ports(struct dsa_switch *ds,
static int _dsa_register_switch(struct dsa_switch *ds, struct device *dev)
{
+ struct dsa_chip_data *pdata = dev->platform_data;
struct device_node *np = dev->of_node;
struct dsa_switch_tree *dst;
struct device_node *ports;
u32 tree, index;
int i, err;
- err = dsa_parse_member_dn(np, &tree, &index);
- if (err)
- return err;
+ if (np) {
+ err = dsa_parse_member_dn(np, &tree, &index);
+ if (err)
+ return err;
- ports = dsa_get_ports(ds, np);
- if (IS_ERR(ports))
- return PTR_ERR(ports);
+ ports = dsa_get_ports(ds, np);
+ if (IS_ERR(ports))
+ return PTR_ERR(ports);
- err = dsa_parse_ports_dn(ports, ds);
- if (err)
- return err;
+ err = dsa_parse_ports_dn(ports, ds);
+ if (err)
+ return err;
+ } else {
+ err = dsa_parse_member(pdata, &tree, &index);
+ if (err)
+ return err;
+
+ err = dsa_parse_ports(pdata, ds);
+ if (err)
+ return err;
+ }
dst = dsa_get_dst(tree);
if (!dst) {
@@ -617,6 +682,7 @@ static int _dsa_register_switch(struct dsa_switch *ds, struct device *dev)
ds->dst = dst;
ds->index = index;
+ ds->cd = pdata;
/* Initialize the routing table */
for (i = 0; i < DSA_MAX_SWITCHES; ++i)
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
2017-02-04 21:02 ` Florian Fainelli
@ 2017-02-04 21:02 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Jason Cooper, Andrew Lunn,
Sebastian Hesselbarth, Gregory Clement, Russell King,
Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/Makefile | 3 +-
drivers/net/phy/mdio-boardinfo.c | 86 ++++++++++++++++++++++++++++++++++++++++
drivers/net/phy/mdio-boardinfo.h | 19 +++++++++
drivers/net/phy/mdio_bus.c | 4 ++
drivers/net/phy/mdio_device.c | 11 +++++
include/linux/mdio.h | 3 ++
include/linux/mod_devicetable.h | 1 +
include/linux/phy.h | 19 +++++++++
8 files changed, 145 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/phy/mdio-boardinfo.c
create mode 100644 drivers/net/phy/mdio-boardinfo.h
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 356859ac7c18..407b0b601ea8 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -1,6 +1,7 @@
# Makefile for Linux PHY drivers and MDIO bus drivers
-libphy-y := phy.o phy_device.o mdio_bus.o mdio_device.o
+libphy-y := phy.o phy_device.o mdio_bus.o mdio_device.o \
+ mdio-boardinfo.o
libphy-$(CONFIG_SWPHY) += swphy.o
libphy-$(CONFIG_LED_TRIGGER_PHY) += phy_led_triggers.o
diff --git a/drivers/net/phy/mdio-boardinfo.c b/drivers/net/phy/mdio-boardinfo.c
new file mode 100644
index 000000000000..6b988f77da08
--- /dev/null
+++ b/drivers/net/phy/mdio-boardinfo.c
@@ -0,0 +1,86 @@
+/*
+ * mdio-boardinfo - Collect pre-declarations for MDIO devices
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/export.h>
+#include <linux/mutex.h>
+#include <linux/list.h>
+
+#include "mdio-boardinfo.h"
+
+static LIST_HEAD(mdio_board_list);
+static DEFINE_MUTEX(mdio_board_lock);
+
+/**
+ * mdiobus_setup_mdiodev_from_board_info - create and setup MDIO devices
+ * from pre-collected board specific MDIO information
+ * @mdiodev: MDIO device pointer
+ * Context: can sleep
+ */
+void mdiobus_setup_mdiodev_from_board_info(struct mii_bus *bus)
+{
+ struct mdio_board_entry *be;
+ struct mdio_device *mdiodev;
+ struct mdio_board_info *bi;
+ int ret;
+
+ mutex_lock(&mdio_board_lock);
+ list_for_each_entry(be, &mdio_board_list, list) {
+ bi = &be->board_info;
+
+ if (strcmp(bus->id, bi->bus_id))
+ continue;
+
+ mdiodev = mdio_device_create(bus, bi->mdio_addr);
+ if (IS_ERR(mdiodev))
+ continue;
+
+ strncpy(mdiodev->modalias, bi->modalias,
+ sizeof(mdiodev->modalias));
+ mdiodev->bus_match = mdio_device_bus_match;
+ mdiodev->dev.platform_data = (void *)bi->platform_data;
+
+ ret = mdio_device_register(mdiodev);
+ if (ret) {
+ mdio_device_free(mdiodev);
+ continue;
+ }
+ }
+ mutex_unlock(&mdio_board_lock);
+}
+
+/**
+ * mdio_register_board_info - register MDIO devices for a given board
+ * @info: array of devices descriptors
+ * @n: number of descriptors provided
+ * Context: can sleep
+ *
+ * The board info passed can be marked with __initdata but be pointers
+ * such as platform_data etc. are copied as-is
+ */
+int mdiobus_register_board_info(const struct mdio_board_info *info,
+ unsigned int n)
+{
+ struct mdio_board_entry *be;
+ unsigned int i;
+
+ be = kcalloc(n, sizeof(*be), GFP_KERNEL);
+ if (!be)
+ return -ENOMEM;
+
+ for (i = 0; i < n; i++, be++, info++) {
+ memcpy(&be->board_info, info, sizeof(*info));
+ mutex_lock(&mdio_board_lock);
+ list_add_tail(&be->list, &mdio_board_list);
+ mutex_unlock(&mdio_board_lock);
+ }
+
+ return 0;
+}
diff --git a/drivers/net/phy/mdio-boardinfo.h b/drivers/net/phy/mdio-boardinfo.h
new file mode 100644
index 000000000000..00f98163e90e
--- /dev/null
+++ b/drivers/net/phy/mdio-boardinfo.h
@@ -0,0 +1,19 @@
+/*
+ * mdio-boardinfo.h - board info interface internal to the mdio_bus
+ * component
+ */
+
+#ifndef __MDIO_BOARD_INFO_H
+#define __MDIO_BOARD_INFO_H
+
+#include <linux/phy.h>
+#include <linux/mutex.h>
+
+struct mdio_board_entry {
+ struct list_head list;
+ struct mdio_board_info board_info;
+};
+
+void mdiobus_setup_mdiodev_from_board_info(struct mii_bus *bus);
+
+#endif /* __MDIO_BOARD_INFO_H */
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 653d076eafe5..fa7d51f14869 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -41,6 +41,8 @@
#define CREATE_TRACE_POINTS
#include <trace/events/mdio.h>
+#include "mdio-boardinfo.h"
+
int mdiobus_register_device(struct mdio_device *mdiodev)
{
if (mdiodev->bus->mdio_map[mdiodev->addr])
@@ -343,6 +345,8 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
}
}
+ mdiobus_setup_mdiodev_from_board_info(bus);
+
bus->state = MDIOBUS_REGISTERED;
pr_info("%s: probed\n", bus->name);
return 0;
diff --git a/drivers/net/phy/mdio_device.c b/drivers/net/phy/mdio_device.c
index fc3aaaa36b1d..e24f28924af8 100644
--- a/drivers/net/phy/mdio_device.c
+++ b/drivers/net/phy/mdio_device.c
@@ -34,6 +34,17 @@ static void mdio_device_release(struct device *dev)
kfree(to_mdio_device(dev));
}
+int mdio_device_bus_match(struct device *dev, struct device_driver *drv)
+{
+ struct mdio_device *mdiodev = to_mdio_device(dev);
+ struct mdio_driver *mdiodrv = to_mdio_driver(drv);
+
+ if (mdiodrv->mdiodrv.flags & MDIO_DEVICE_IS_PHY)
+ return 0;
+
+ return strcmp(mdiodev->modalias, drv->name) == 0;
+}
+
struct mdio_device *mdio_device_create(struct mii_bus *bus, int addr)
{
struct mdio_device *mdiodev;
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index 55a80d73cfc1..ca08ab16ecdc 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -10,6 +10,7 @@
#define __LINUX_MDIO_H__
#include <uapi/linux/mdio.h>
+#include <linux/mod_devicetable.h>
struct mii_bus;
@@ -29,6 +30,7 @@ struct mdio_device {
const struct dev_pm_ops *pm_ops;
struct mii_bus *bus;
+ char modalias[MDIO_NAME_SIZE];
int (*bus_match)(struct device *dev, struct device_driver *drv);
void (*device_free)(struct mdio_device *mdiodev);
@@ -71,6 +73,7 @@ int mdio_device_register(struct mdio_device *mdiodev);
void mdio_device_remove(struct mdio_device *mdiodev);
int mdio_driver_register(struct mdio_driver *drv);
void mdio_driver_unregister(struct mdio_driver *drv);
+int mdio_device_bus_match(struct device *dev, struct device_driver *drv);
static inline bool mdio_phy_id_is_c45(int phy_id)
{
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 8a57f0b1242d..8850fcaf50db 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -501,6 +501,7 @@ struct platform_device_id {
kernel_ulong_t driver_data;
};
+#define MDIO_NAME_SIZE 32
#define MDIO_MODULE_PREFIX "mdio:"
#define MDIO_ID_FMT "%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d"
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 43474f39ef65..8ddef0fb83d0 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -877,6 +877,25 @@ void mdio_bus_exit(void);
extern struct bus_type mdio_bus_type;
+struct mdio_board_info {
+ const char *bus_id;
+ char modalias[MDIO_NAME_SIZE];
+ int mdio_addr;
+ const void *platform_data;
+};
+
+#if IS_ENABLED(CONFIG_PHYLIB)
+int mdiobus_register_board_info(const struct mdio_board_info *info,
+ unsigned int n);
+#else
+static inline int mdiobus_register_board_info(const struct mdio_board_info *i,
+ unsigned int n)
+{
+ return 0;
+}
+#endif
+
+
/**
* module_phy_driver() - Helper macro for registering PHY drivers
* @__phy_drivers: array of PHY drivers to register
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-04 21:02 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: linux-arm-kernel
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/Makefile | 3 +-
drivers/net/phy/mdio-boardinfo.c | 86 ++++++++++++++++++++++++++++++++++++++++
drivers/net/phy/mdio-boardinfo.h | 19 +++++++++
drivers/net/phy/mdio_bus.c | 4 ++
drivers/net/phy/mdio_device.c | 11 +++++
include/linux/mdio.h | 3 ++
include/linux/mod_devicetable.h | 1 +
include/linux/phy.h | 19 +++++++++
8 files changed, 145 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/phy/mdio-boardinfo.c
create mode 100644 drivers/net/phy/mdio-boardinfo.h
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 356859ac7c18..407b0b601ea8 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -1,6 +1,7 @@
# Makefile for Linux PHY drivers and MDIO bus drivers
-libphy-y := phy.o phy_device.o mdio_bus.o mdio_device.o
+libphy-y := phy.o phy_device.o mdio_bus.o mdio_device.o \
+ mdio-boardinfo.o
libphy-$(CONFIG_SWPHY) += swphy.o
libphy-$(CONFIG_LED_TRIGGER_PHY) += phy_led_triggers.o
diff --git a/drivers/net/phy/mdio-boardinfo.c b/drivers/net/phy/mdio-boardinfo.c
new file mode 100644
index 000000000000..6b988f77da08
--- /dev/null
+++ b/drivers/net/phy/mdio-boardinfo.c
@@ -0,0 +1,86 @@
+/*
+ * mdio-boardinfo - Collect pre-declarations for MDIO devices
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/export.h>
+#include <linux/mutex.h>
+#include <linux/list.h>
+
+#include "mdio-boardinfo.h"
+
+static LIST_HEAD(mdio_board_list);
+static DEFINE_MUTEX(mdio_board_lock);
+
+/**
+ * mdiobus_setup_mdiodev_from_board_info - create and setup MDIO devices
+ * from pre-collected board specific MDIO information
+ * @mdiodev: MDIO device pointer
+ * Context: can sleep
+ */
+void mdiobus_setup_mdiodev_from_board_info(struct mii_bus *bus)
+{
+ struct mdio_board_entry *be;
+ struct mdio_device *mdiodev;
+ struct mdio_board_info *bi;
+ int ret;
+
+ mutex_lock(&mdio_board_lock);
+ list_for_each_entry(be, &mdio_board_list, list) {
+ bi = &be->board_info;
+
+ if (strcmp(bus->id, bi->bus_id))
+ continue;
+
+ mdiodev = mdio_device_create(bus, bi->mdio_addr);
+ if (IS_ERR(mdiodev))
+ continue;
+
+ strncpy(mdiodev->modalias, bi->modalias,
+ sizeof(mdiodev->modalias));
+ mdiodev->bus_match = mdio_device_bus_match;
+ mdiodev->dev.platform_data = (void *)bi->platform_data;
+
+ ret = mdio_device_register(mdiodev);
+ if (ret) {
+ mdio_device_free(mdiodev);
+ continue;
+ }
+ }
+ mutex_unlock(&mdio_board_lock);
+}
+
+/**
+ * mdio_register_board_info - register MDIO devices for a given board
+ * @info: array of devices descriptors
+ * @n: number of descriptors provided
+ * Context: can sleep
+ *
+ * The board info passed can be marked with __initdata but be pointers
+ * such as platform_data etc. are copied as-is
+ */
+int mdiobus_register_board_info(const struct mdio_board_info *info,
+ unsigned int n)
+{
+ struct mdio_board_entry *be;
+ unsigned int i;
+
+ be = kcalloc(n, sizeof(*be), GFP_KERNEL);
+ if (!be)
+ return -ENOMEM;
+
+ for (i = 0; i < n; i++, be++, info++) {
+ memcpy(&be->board_info, info, sizeof(*info));
+ mutex_lock(&mdio_board_lock);
+ list_add_tail(&be->list, &mdio_board_list);
+ mutex_unlock(&mdio_board_lock);
+ }
+
+ return 0;
+}
diff --git a/drivers/net/phy/mdio-boardinfo.h b/drivers/net/phy/mdio-boardinfo.h
new file mode 100644
index 000000000000..00f98163e90e
--- /dev/null
+++ b/drivers/net/phy/mdio-boardinfo.h
@@ -0,0 +1,19 @@
+/*
+ * mdio-boardinfo.h - board info interface internal to the mdio_bus
+ * component
+ */
+
+#ifndef __MDIO_BOARD_INFO_H
+#define __MDIO_BOARD_INFO_H
+
+#include <linux/phy.h>
+#include <linux/mutex.h>
+
+struct mdio_board_entry {
+ struct list_head list;
+ struct mdio_board_info board_info;
+};
+
+void mdiobus_setup_mdiodev_from_board_info(struct mii_bus *bus);
+
+#endif /* __MDIO_BOARD_INFO_H */
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 653d076eafe5..fa7d51f14869 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -41,6 +41,8 @@
#define CREATE_TRACE_POINTS
#include <trace/events/mdio.h>
+#include "mdio-boardinfo.h"
+
int mdiobus_register_device(struct mdio_device *mdiodev)
{
if (mdiodev->bus->mdio_map[mdiodev->addr])
@@ -343,6 +345,8 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
}
}
+ mdiobus_setup_mdiodev_from_board_info(bus);
+
bus->state = MDIOBUS_REGISTERED;
pr_info("%s: probed\n", bus->name);
return 0;
diff --git a/drivers/net/phy/mdio_device.c b/drivers/net/phy/mdio_device.c
index fc3aaaa36b1d..e24f28924af8 100644
--- a/drivers/net/phy/mdio_device.c
+++ b/drivers/net/phy/mdio_device.c
@@ -34,6 +34,17 @@ static void mdio_device_release(struct device *dev)
kfree(to_mdio_device(dev));
}
+int mdio_device_bus_match(struct device *dev, struct device_driver *drv)
+{
+ struct mdio_device *mdiodev = to_mdio_device(dev);
+ struct mdio_driver *mdiodrv = to_mdio_driver(drv);
+
+ if (mdiodrv->mdiodrv.flags & MDIO_DEVICE_IS_PHY)
+ return 0;
+
+ return strcmp(mdiodev->modalias, drv->name) == 0;
+}
+
struct mdio_device *mdio_device_create(struct mii_bus *bus, int addr)
{
struct mdio_device *mdiodev;
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index 55a80d73cfc1..ca08ab16ecdc 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -10,6 +10,7 @@
#define __LINUX_MDIO_H__
#include <uapi/linux/mdio.h>
+#include <linux/mod_devicetable.h>
struct mii_bus;
@@ -29,6 +30,7 @@ struct mdio_device {
const struct dev_pm_ops *pm_ops;
struct mii_bus *bus;
+ char modalias[MDIO_NAME_SIZE];
int (*bus_match)(struct device *dev, struct device_driver *drv);
void (*device_free)(struct mdio_device *mdiodev);
@@ -71,6 +73,7 @@ int mdio_device_register(struct mdio_device *mdiodev);
void mdio_device_remove(struct mdio_device *mdiodev);
int mdio_driver_register(struct mdio_driver *drv);
void mdio_driver_unregister(struct mdio_driver *drv);
+int mdio_device_bus_match(struct device *dev, struct device_driver *drv);
static inline bool mdio_phy_id_is_c45(int phy_id)
{
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 8a57f0b1242d..8850fcaf50db 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -501,6 +501,7 @@ struct platform_device_id {
kernel_ulong_t driver_data;
};
+#define MDIO_NAME_SIZE 32
#define MDIO_MODULE_PREFIX "mdio:"
#define MDIO_ID_FMT "%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d"
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 43474f39ef65..8ddef0fb83d0 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -877,6 +877,25 @@ void mdio_bus_exit(void);
extern struct bus_type mdio_bus_type;
+struct mdio_board_info {
+ const char *bus_id;
+ char modalias[MDIO_NAME_SIZE];
+ int mdio_addr;
+ const void *platform_data;
+};
+
+#if IS_ENABLED(CONFIG_PHYLIB)
+int mdiobus_register_board_info(const struct mdio_board_info *info,
+ unsigned int n);
+#else
+static inline int mdiobus_register_board_info(const struct mdio_board_info *i,
+ unsigned int n)
+{
+ return 0;
+}
+#endif
+
+
/**
* module_phy_driver() - Helper macro for registering PHY drivers
* @__phy_drivers: array of PHY drivers to register
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
2017-02-04 21:02 ` Florian Fainelli
(?)
@ 2017-02-06 13:48 ` Andrew Lunn
-1 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 13:48 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
> index 8a57f0b1242d..8850fcaf50db 100644
> --- a/include/linux/mod_devicetable.h
> +++ b/include/linux/mod_devicetable.h
> @@ -501,6 +501,7 @@ struct platform_device_id {
> kernel_ulong_t driver_data;
> };
>
> +#define MDIO_NAME_SIZE 32
...
> +struct mdio_board_info {
> + const char *bus_id;
> + char modalias[MDIO_NAME_SIZE];
> +
I think it might be better to use MII_BUS_ID_SIZE. These are all
related, so using one define should avoid surprise buffer overruns,
truncation's.
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 13:48 ` Andrew Lunn
0 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 13:48 UTC (permalink / raw)
To: linux-arm-kernel
> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
> index 8a57f0b1242d..8850fcaf50db 100644
> --- a/include/linux/mod_devicetable.h
> +++ b/include/linux/mod_devicetable.h
> @@ -501,6 +501,7 @@ struct platform_device_id {
> kernel_ulong_t driver_data;
> };
>
> +#define MDIO_NAME_SIZE 32
...
> +struct mdio_board_info {
> + const char *bus_id;
> + char modalias[MDIO_NAME_SIZE];
> +
I think it might be better to use MII_BUS_ID_SIZE. These are all
related, so using one define should avoid surprise buffer overruns,
truncation's.
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 13:48 ` Andrew Lunn
0 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 13:48 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
> index 8a57f0b1242d..8850fcaf50db 100644
> --- a/include/linux/mod_devicetable.h
> +++ b/include/linux/mod_devicetable.h
> @@ -501,6 +501,7 @@ struct platform_device_id {
> kernel_ulong_t driver_data;
> };
>
> +#define MDIO_NAME_SIZE 32
...
> +struct mdio_board_info {
> + const char *bus_id;
> + char modalias[MDIO_NAME_SIZE];
> +
I think it might be better to use MII_BUS_ID_SIZE. These are all
related, so using one define should avoid surprise buffer overruns,
truncation's.
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
2017-02-06 13:48 ` Andrew Lunn
(?)
@ 2017-02-06 19:08 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:08 UTC (permalink / raw)
To: Andrew Lunn
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
On 02/06/2017 05:48 AM, Andrew Lunn wrote:
>> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
>> index 8a57f0b1242d..8850fcaf50db 100644
>> --- a/include/linux/mod_devicetable.h
>> +++ b/include/linux/mod_devicetable.h
>> @@ -501,6 +501,7 @@ struct platform_device_id {
>> kernel_ulong_t driver_data;
>> };
>>
>> +#define MDIO_NAME_SIZE 32
>
> ...
>
>> +struct mdio_board_info {
>> + const char *bus_id;
>> + char modalias[MDIO_NAME_SIZE];
>> +
>
> I think it might be better to use MII_BUS_ID_SIZE. These are all
> related, so using one define should avoid surprise buffer overruns,
> truncation's.
I considered doing that, but left it that way because I valued the
"const" qualifier more than running out of buffer space. What I could do
though, is change the strcmp() in drivers/net/phy/mdio-boardinfo.c to be
bound by MII_BUS_ID_SIZE.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 19:08 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:08 UTC (permalink / raw)
To: linux-arm-kernel
On 02/06/2017 05:48 AM, Andrew Lunn wrote:
>> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
>> index 8a57f0b1242d..8850fcaf50db 100644
>> --- a/include/linux/mod_devicetable.h
>> +++ b/include/linux/mod_devicetable.h
>> @@ -501,6 +501,7 @@ struct platform_device_id {
>> kernel_ulong_t driver_data;
>> };
>>
>> +#define MDIO_NAME_SIZE 32
>
> ...
>
>> +struct mdio_board_info {
>> + const char *bus_id;
>> + char modalias[MDIO_NAME_SIZE];
>> +
>
> I think it might be better to use MII_BUS_ID_SIZE. These are all
> related, so using one define should avoid surprise buffer overruns,
> truncation's.
I considered doing that, but left it that way because I valued the
"const" qualifier more than running out of buffer space. What I could do
though, is change the strcmp() in drivers/net/phy/mdio-boardinfo.c to be
bound by MII_BUS_ID_SIZE.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 19:08 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:08 UTC (permalink / raw)
To: Andrew Lunn
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
On 02/06/2017 05:48 AM, Andrew Lunn wrote:
>> diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
>> index 8a57f0b1242d..8850fcaf50db 100644
>> --- a/include/linux/mod_devicetable.h
>> +++ b/include/linux/mod_devicetable.h
>> @@ -501,6 +501,7 @@ struct platform_device_id {
>> kernel_ulong_t driver_data;
>> };
>>
>> +#define MDIO_NAME_SIZE 32
>
> ...
>
>> +struct mdio_board_info {
>> + const char *bus_id;
>> + char modalias[MDIO_NAME_SIZE];
>> +
>
> I think it might be better to use MII_BUS_ID_SIZE. These are all
> related, so using one define should avoid surprise buffer overruns,
> truncation's.
I considered doing that, but left it that way because I valued the
"const" qualifier more than running out of buffer space. What I could do
though, is change the strcmp() in drivers/net/phy/mdio-boardinfo.c to be
bound by MII_BUS_ID_SIZE.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
2017-02-04 21:02 ` Florian Fainelli
(?)
@ 2017-02-06 14:04 ` Andrew Lunn
-1 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 14:04 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
> +/**
> + * mdio_register_board_info - register MDIO devices for a given board
> + * @info: array of devices descriptors
> + * @n: number of descriptors provided
> + * Context: can sleep
> + *
> + * The board info passed can be marked with __initdata but be pointers
> + * such as platform_data etc. are copied as-is
> + */
> +int mdiobus_register_board_info(const struct mdio_board_info *info,
> + unsigned int n)
> +{
> + struct mdio_board_entry *be;
> + unsigned int i;
> +
> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
> + if (!be)
> + return -ENOMEM;
> +
> + for (i = 0; i < n; i++, be++, info++) {
> + memcpy(&be->board_info, info, sizeof(*info));
> + mutex_lock(&mdio_board_lock);
> + list_add_tail(&be->list, &mdio_board_list);
> + mutex_unlock(&mdio_board_lock);
> + }
> +
> + return 0;
Hi Florian
I've recently been playing with a hot-pluggable SPI bus controller. It
is a USB device, hence can come and go. On the SPI bus i have an
SRAM. On order to instantiate the MTD device, i need SPI board info. I
cannot add the board info until after the SPI bus master appears,
since i need to know its ID to fill in the board info. At the moment,
i have udev script which when the SPI bus master appears loads a
little kernel module which registers the board info.
Such a scheme will not work here. You need to iterate the list of MDIO
devices at the end of mdiobus_register_board_info() to see if the just
registered board info applies to any existing MDIO bus.
I don't think we yet have any hardware which would do this. But there
have been patches to one of the USB-Ethernet dongles to allow it run
without a PHY. My guess is, to allow an SFP module. But it is not too
big a step for somebody to make a USB attached Ethernet switch.
Maybe consider adding this functionality? Also an unregister call?
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 14:04 ` Andrew Lunn
0 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 14:04 UTC (permalink / raw)
To: linux-arm-kernel
> +/**
> + * mdio_register_board_info - register MDIO devices for a given board
> + * @info: array of devices descriptors
> + * @n: number of descriptors provided
> + * Context: can sleep
> + *
> + * The board info passed can be marked with __initdata but be pointers
> + * such as platform_data etc. are copied as-is
> + */
> +int mdiobus_register_board_info(const struct mdio_board_info *info,
> + unsigned int n)
> +{
> + struct mdio_board_entry *be;
> + unsigned int i;
> +
> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
> + if (!be)
> + return -ENOMEM;
> +
> + for (i = 0; i < n; i++, be++, info++) {
> + memcpy(&be->board_info, info, sizeof(*info));
> + mutex_lock(&mdio_board_lock);
> + list_add_tail(&be->list, &mdio_board_list);
> + mutex_unlock(&mdio_board_lock);
> + }
> +
> + return 0;
Hi Florian
I've recently been playing with a hot-pluggable SPI bus controller. It
is a USB device, hence can come and go. On the SPI bus i have an
SRAM. On order to instantiate the MTD device, i need SPI board info. I
cannot add the board info until after the SPI bus master appears,
since i need to know its ID to fill in the board info. At the moment,
i have udev script which when the SPI bus master appears loads a
little kernel module which registers the board info.
Such a scheme will not work here. You need to iterate the list of MDIO
devices at the end of mdiobus_register_board_info() to see if the just
registered board info applies to any existing MDIO bus.
I don't think we yet have any hardware which would do this. But there
have been patches to one of the USB-Ethernet dongles to allow it run
without a PHY. My guess is, to allow an SFP module. But it is not too
big a step for somebody to make a USB attached Ethernet switch.
Maybe consider adding this functionality? Also an unregister call?
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 14:04 ` Andrew Lunn
0 siblings, 0 replies; 22+ messages in thread
From: Andrew Lunn @ 2017-02-06 14:04 UTC (permalink / raw)
To: Florian Fainelli
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
> +/**
> + * mdio_register_board_info - register MDIO devices for a given board
> + * @info: array of devices descriptors
> + * @n: number of descriptors provided
> + * Context: can sleep
> + *
> + * The board info passed can be marked with __initdata but be pointers
> + * such as platform_data etc. are copied as-is
> + */
> +int mdiobus_register_board_info(const struct mdio_board_info *info,
> + unsigned int n)
> +{
> + struct mdio_board_entry *be;
> + unsigned int i;
> +
> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
> + if (!be)
> + return -ENOMEM;
> +
> + for (i = 0; i < n; i++, be++, info++) {
> + memcpy(&be->board_info, info, sizeof(*info));
> + mutex_lock(&mdio_board_lock);
> + list_add_tail(&be->list, &mdio_board_list);
> + mutex_unlock(&mdio_board_lock);
> + }
> +
> + return 0;
Hi Florian
I've recently been playing with a hot-pluggable SPI bus controller. It
is a USB device, hence can come and go. On the SPI bus i have an
SRAM. On order to instantiate the MTD device, i need SPI board info. I
cannot add the board info until after the SPI bus master appears,
since i need to know its ID to fill in the board info. At the moment,
i have udev script which when the SPI bus master appears loads a
little kernel module which registers the board info.
Such a scheme will not work here. You need to iterate the list of MDIO
devices at the end of mdiobus_register_board_info() to see if the just
registered board info applies to any existing MDIO bus.
I don't think we yet have any hardware which would do this. But there
have been patches to one of the USB-Ethernet dongles to allow it run
without a PHY. My guess is, to allow an SFP module. But it is not too
big a step for somebody to make a USB attached Ethernet switch.
Maybe consider adding this functionality? Also an unregister call?
Andrew
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
2017-02-06 14:04 ` Andrew Lunn
(?)
@ 2017-02-06 19:17 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:17 UTC (permalink / raw)
To: Andrew Lunn
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
On 02/06/2017 06:04 AM, Andrew Lunn wrote:
>> +/**
>> + * mdio_register_board_info - register MDIO devices for a given board
>> + * @info: array of devices descriptors
>> + * @n: number of descriptors provided
>> + * Context: can sleep
>> + *
>> + * The board info passed can be marked with __initdata but be pointers
>> + * such as platform_data etc. are copied as-is
>> + */
>> +int mdiobus_register_board_info(const struct mdio_board_info *info,
>> + unsigned int n)
>> +{
>> + struct mdio_board_entry *be;
>> + unsigned int i;
>> +
>> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
>> + if (!be)
>> + return -ENOMEM;
>> +
>> + for (i = 0; i < n; i++, be++, info++) {
>> + memcpy(&be->board_info, info, sizeof(*info));
>> + mutex_lock(&mdio_board_lock);
>> + list_add_tail(&be->list, &mdio_board_list);
>> + mutex_unlock(&mdio_board_lock);
>> + }
>> +
>> + return 0;
>
> Hi Florian
>
> I've recently been playing with a hot-pluggable SPI bus controller. It
> is a USB device, hence can come and go. On the SPI bus i have an
> SRAM. On order to instantiate the MTD device, i need SPI board info. I
> cannot add the board info until after the SPI bus master appears,
> since i need to know its ID to fill in the board info. At the moment,
> i have udev script which when the SPI bus master appears loads a
> little kernel module which registers the board info.
>
> Such a scheme will not work here. You need to iterate the list of MDIO
> devices at the end of mdiobus_register_board_info() to see if the just
> registered board info applies to any existing MDIO bus.
I was thinking when mdio_device_register() is called, see if there is a
matching board info for it, and if so, assign its platform_data
accordingly. In the case where mdiobus_register_with_board
>
> I don't think we yet have any hardware which would do this. But there
> have been patches to one of the USB-Ethernet dongles to allow it run
> without a PHY. My guess is, to allow an SFP module. But it is not too
> big a step for somebody to make a USB attached Ethernet switch.
>
> Maybe consider adding this functionality? Also an unregister call?
Sure, makes sense.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 19:17 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:17 UTC (permalink / raw)
To: linux-arm-kernel
On 02/06/2017 06:04 AM, Andrew Lunn wrote:
>> +/**
>> + * mdio_register_board_info - register MDIO devices for a given board
>> + * @info: array of devices descriptors
>> + * @n: number of descriptors provided
>> + * Context: can sleep
>> + *
>> + * The board info passed can be marked with __initdata but be pointers
>> + * such as platform_data etc. are copied as-is
>> + */
>> +int mdiobus_register_board_info(const struct mdio_board_info *info,
>> + unsigned int n)
>> +{
>> + struct mdio_board_entry *be;
>> + unsigned int i;
>> +
>> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
>> + if (!be)
>> + return -ENOMEM;
>> +
>> + for (i = 0; i < n; i++, be++, info++) {
>> + memcpy(&be->board_info, info, sizeof(*info));
>> + mutex_lock(&mdio_board_lock);
>> + list_add_tail(&be->list, &mdio_board_list);
>> + mutex_unlock(&mdio_board_lock);
>> + }
>> +
>> + return 0;
>
> Hi Florian
>
> I've recently been playing with a hot-pluggable SPI bus controller. It
> is a USB device, hence can come and go. On the SPI bus i have an
> SRAM. On order to instantiate the MTD device, i need SPI board info. I
> cannot add the board info until after the SPI bus master appears,
> since i need to know its ID to fill in the board info. At the moment,
> i have udev script which when the SPI bus master appears loads a
> little kernel module which registers the board info.
>
> Such a scheme will not work here. You need to iterate the list of MDIO
> devices at the end of mdiobus_register_board_info() to see if the just
> registered board info applies to any existing MDIO bus.
I was thinking when mdio_device_register() is called, see if there is a
matching board info for it, and if so, assign its platform_data
accordingly. In the case where mdiobus_register_with_board
>
> I don't think we yet have any hardware which would do this. But there
> have been patches to one of the USB-Ethernet dongles to allow it run
> without a PHY. My guess is, to allow an SFP module. But it is not too
> big a step for somebody to make a USB attached Ethernet switch.
>
> Maybe consider adding this functionality? Also an unregister call?
Sure, makes sense.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH net-next v5 3/4] net: phy: Allow pre-declaration of MDIO devices
@ 2017-02-06 19:17 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-06 19:17 UTC (permalink / raw)
To: Andrew Lunn
Cc: netdev, Jason Cooper, Sebastian Hesselbarth, Gregory Clement,
Russell King, Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
On 02/06/2017 06:04 AM, Andrew Lunn wrote:
>> +/**
>> + * mdio_register_board_info - register MDIO devices for a given board
>> + * @info: array of devices descriptors
>> + * @n: number of descriptors provided
>> + * Context: can sleep
>> + *
>> + * The board info passed can be marked with __initdata but be pointers
>> + * such as platform_data etc. are copied as-is
>> + */
>> +int mdiobus_register_board_info(const struct mdio_board_info *info,
>> + unsigned int n)
>> +{
>> + struct mdio_board_entry *be;
>> + unsigned int i;
>> +
>> + be = kcalloc(n, sizeof(*be), GFP_KERNEL);
>> + if (!be)
>> + return -ENOMEM;
>> +
>> + for (i = 0; i < n; i++, be++, info++) {
>> + memcpy(&be->board_info, info, sizeof(*info));
>> + mutex_lock(&mdio_board_lock);
>> + list_add_tail(&be->list, &mdio_board_list);
>> + mutex_unlock(&mdio_board_lock);
>> + }
>> +
>> + return 0;
>
> Hi Florian
>
> I've recently been playing with a hot-pluggable SPI bus controller. It
> is a USB device, hence can come and go. On the SPI bus i have an
> SRAM. On order to instantiate the MTD device, i need SPI board info. I
> cannot add the board info until after the SPI bus master appears,
> since i need to know its ID to fill in the board info. At the moment,
> i have udev script which when the SPI bus master appears loads a
> little kernel module which registers the board info.
>
> Such a scheme will not work here. You need to iterate the list of MDIO
> devices at the end of mdiobus_register_board_info() to see if the just
> registered board info applies to any existing MDIO bus.
I was thinking when mdio_device_register() is called, see if there is a
matching board info for it, and if so, assign its platform_data
accordingly. In the case where mdiobus_register_with_board
>
> I don't think we yet have any hardware which would do this. But there
> have been patches to one of the USB-Ethernet dongles to allow it run
> without a PHY. My guess is, to allow an SFP module. But it is not too
> big a step for somebody to make a USB attached Ethernet switch.
>
> Maybe consider adding this functionality? Also an unregister call?
Sure, makes sense.
--
Florian
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH net-next v5 4/4] ARM: orion: Register DSA switch as a MDIO device
2017-02-04 21:02 ` Florian Fainelli
@ 2017-02-04 21:02 ` Florian Fainelli
-1 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: netdev
Cc: Florian Fainelli, Jason Cooper, Andrew Lunn,
Sebastian Hesselbarth, Gregory Clement, Russell King,
Vivien Didelot, David S. Miller,
moderated list:ARM/Marvell Dove/MV78xx0/Orion SOC support,
open list
Utilize the ability to pass board specific MDIO bus information towards a
particular MDIO device thus allowing us to provide the per-port switch layout
to the Marvell 88E6XXX switch driver.
Since we would end-up with conflicting registration paths, do not register the
"dsa" platform device anymore.
Note that the MDIO devices registered by code in net/dsa/dsa2.c does not
parse a dsa_platform_data, but directly take a dsa_chip_data (specific
to a single switch chip), so we update the different call sites to pass
this structure down to orion_ge00_switch_init().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/mach-orion5x/common.c | 2 +-
arch/arm/mach-orion5x/common.h | 4 ++--
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 7 +------
arch/arm/mach-orion5x/wnr854t-setup.c | 2 +-
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 7 +------
arch/arm/plat-orion/common.c | 25 +++++++++++++++++++------
arch/arm/plat-orion/include/plat/common.h | 4 ++--
9 files changed, 29 insertions(+), 36 deletions(-)
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 04910764c385..83a7ec4c16d0 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -105,7 +105,7 @@ void __init orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data)
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion5x_eth_switch_init(struct dsa_platform_data *d)
+void __init orion5x_eth_switch_init(struct dsa_chip_data *d)
{
orion_ge00_switch_init(d);
}
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 8a4115bd441d..efeffc6b4ebb 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -3,7 +3,7 @@
#include <linux/reboot.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv643xx_eth_platform_data;
struct mv_sata_platform_data;
@@ -41,7 +41,7 @@ void orion5x_setup_wins(void);
void orion5x_ehci0_init(void);
void orion5x_ehci1_init(void);
void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
-void orion5x_eth_switch_init(struct dsa_platform_data *d);
+void orion5x_eth_switch_init(struct dsa_chip_data *d);
void orion5x_i2c_init(void);
void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
void orion5x_spi_init(void);
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index dccadf68ea2b..a3c1336d30c9 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -101,11 +101,6 @@ static struct dsa_chip_data rd88f5181l_fxo_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_fxo_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_fxo_switch_chip_data,
-};
-
static void __init rd88f5181l_fxo_init(void)
{
/*
@@ -120,7 +115,7 @@ static void __init rd88f5181l_fxo_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_fxo_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index affe5ec825de..252efe29bd1a 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -102,11 +102,6 @@ static struct dsa_chip_data rd88f5181l_ge_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_ge_switch_chip_data,
-};
-
static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {
I2C_BOARD_INFO("ds1338", 0x68),
};
@@ -125,7 +120,7 @@ static void __init rd88f5181l_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_ge_switch_chip_data);
orion5x_i2c_init();
orion5x_uart0_init();
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index 67ee8571b03c..f4f1dbe1d91d 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -40,11 +40,6 @@ static struct dsa_chip_data rd88f6183ap_ge_switch_chip_data = {
.port_names[5] = "cpu",
};
-static struct dsa_platform_data __initdata rd88f6183ap_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f6183ap_ge_switch_chip_data,
-};
-
static struct mtd_partition rd88f6183ap_ge_partitions[] = {
{
.name = "kernel",
@@ -89,7 +84,7 @@ static void __init rd88f6183ap_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
- orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f6183ap_ge_switch_chip_data);
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 4dbcdbe1de7c..ac3376fc269f 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -124,7 +124,7 @@ static void __init wnr854t_init(void)
* Configure peripherals.
*/
orion5x_eth_init(&wnr854t_eth_data);
- orion5x_eth_switch_init(&wnr854t_switch_plat_data);
+ orion5x_eth_switch_init(&wnr854t_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index a6a8c4648d74..9250bb2e429c 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -191,11 +191,6 @@ static struct dsa_chip_data wrt350n_v2_switch_chip_data = {
.port_names[7] = "lan4",
};
-static struct dsa_platform_data __initdata wrt350n_v2_switch_plat_data = {
- .nr_chips = 1,
- .chip = &wrt350n_v2_switch_chip_data,
-};
-
static void __init wrt350n_v2_init(void)
{
/*
@@ -210,7 +205,7 @@ static void __init wrt350n_v2_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
- orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data);
+ orion5x_eth_switch_init(&wrt350n_v2_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c
index 272f49b2c68f..9255b6d67ba5 100644
--- a/arch/arm/plat-orion/common.c
+++ b/arch/arm/plat-orion/common.c
@@ -22,6 +22,7 @@
#include <linux/platform_data/dma-mv_xor.h>
#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
+#include <linux/phy.h>
/* Create a clkdev entry for a given device/clk */
void __init orion_clkdev_add(const char *con_id, const char *dev_id,
@@ -470,15 +471,27 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion_ge00_switch_init(struct dsa_platform_data *d)
+static __initconst const char *orion_ge00_mvmdio_bus_name = "orion-mii";
+static __initdata struct mdio_board_info
+ orion_ge00_switch_board_info;
+
+void __init orion_ge00_switch_init(struct dsa_chip_data *d)
{
- int i;
+ struct mdio_board_info *bd;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(d->port_names); i++)
+ if (!strcmp(d->port_names[i], "cpu"))
+ break;
- d->netdev = &orion_ge00.dev;
- for (i = 0; i < d->nr_chips; i++)
- d->chip[i].host_dev = &orion_ge_mvmdio.dev;
+ bd = &orion_ge00_switch_board_info;
+ bd->bus_id = orion_ge00_mvmdio_bus_name;
+ bd->mdio_addr = d->sw_addr;
+ d->netdev[i] = &orion_ge00.dev;
+ strcpy(bd->modalias, "mv88e6085");
+ bd->platform_data = d;
- platform_device_register_data(NULL, "dsa", 0, d, sizeof(d));
+ mdiobus_register_board_info(&orion_ge00_switch_board_info, 1);
}
/*****************************************************************************
diff --git a/arch/arm/plat-orion/include/plat/common.h b/arch/arm/plat-orion/include/plat/common.h
index 9347f3c58a6d..3647d3b33c20 100644
--- a/arch/arm/plat-orion/include/plat/common.h
+++ b/arch/arm/plat-orion/include/plat/common.h
@@ -12,7 +12,7 @@
#include <linux/mv643xx_eth.h>
#include <linux/platform_data/usb-ehci-orion.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv_sata_platform_data;
void __init orion_uart0_init(void __iomem *membase,
@@ -57,7 +57,7 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq);
-void __init orion_ge00_switch_init(struct dsa_platform_data *d);
+void __init orion_ge00_switch_init(struct dsa_chip_data *d);
void __init orion_i2c_init(unsigned long mapbase,
unsigned long irq,
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH net-next v5 4/4] ARM: orion: Register DSA switch as a MDIO device
@ 2017-02-04 21:02 ` Florian Fainelli
0 siblings, 0 replies; 22+ messages in thread
From: Florian Fainelli @ 2017-02-04 21:02 UTC (permalink / raw)
To: linux-arm-kernel
Utilize the ability to pass board specific MDIO bus information towards a
particular MDIO device thus allowing us to provide the per-port switch layout
to the Marvell 88E6XXX switch driver.
Since we would end-up with conflicting registration paths, do not register the
"dsa" platform device anymore.
Note that the MDIO devices registered by code in net/dsa/dsa2.c does not
parse a dsa_platform_data, but directly take a dsa_chip_data (specific
to a single switch chip), so we update the different call sites to pass
this structure down to orion_ge00_switch_init().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/mach-orion5x/common.c | 2 +-
arch/arm/mach-orion5x/common.h | 4 ++--
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 7 +------
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 7 +------
arch/arm/mach-orion5x/wnr854t-setup.c | 2 +-
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 7 +------
arch/arm/plat-orion/common.c | 25 +++++++++++++++++++------
arch/arm/plat-orion/include/plat/common.h | 4 ++--
9 files changed, 29 insertions(+), 36 deletions(-)
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 04910764c385..83a7ec4c16d0 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -105,7 +105,7 @@ void __init orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data)
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion5x_eth_switch_init(struct dsa_platform_data *d)
+void __init orion5x_eth_switch_init(struct dsa_chip_data *d)
{
orion_ge00_switch_init(d);
}
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 8a4115bd441d..efeffc6b4ebb 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -3,7 +3,7 @@
#include <linux/reboot.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv643xx_eth_platform_data;
struct mv_sata_platform_data;
@@ -41,7 +41,7 @@ void orion5x_setup_wins(void);
void orion5x_ehci0_init(void);
void orion5x_ehci1_init(void);
void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
-void orion5x_eth_switch_init(struct dsa_platform_data *d);
+void orion5x_eth_switch_init(struct dsa_chip_data *d);
void orion5x_i2c_init(void);
void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
void orion5x_spi_init(void);
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index dccadf68ea2b..a3c1336d30c9 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -101,11 +101,6 @@ static struct dsa_chip_data rd88f5181l_fxo_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_fxo_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_fxo_switch_chip_data,
-};
-
static void __init rd88f5181l_fxo_init(void)
{
/*
@@ -120,7 +115,7 @@ static void __init rd88f5181l_fxo_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_fxo_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index affe5ec825de..252efe29bd1a 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -102,11 +102,6 @@ static struct dsa_chip_data rd88f5181l_ge_switch_chip_data = {
.port_names[7] = "lan3",
};
-static struct dsa_platform_data __initdata rd88f5181l_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f5181l_ge_switch_chip_data,
-};
-
static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {
I2C_BOARD_INFO("ds1338", 0x68),
};
@@ -125,7 +120,7 @@ static void __init rd88f5181l_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
- orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f5181l_ge_switch_chip_data);
orion5x_i2c_init();
orion5x_uart0_init();
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index 67ee8571b03c..f4f1dbe1d91d 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -40,11 +40,6 @@ static struct dsa_chip_data rd88f6183ap_ge_switch_chip_data = {
.port_names[5] = "cpu",
};
-static struct dsa_platform_data __initdata rd88f6183ap_ge_switch_plat_data = {
- .nr_chips = 1,
- .chip = &rd88f6183ap_ge_switch_chip_data,
-};
-
static struct mtd_partition rd88f6183ap_ge_partitions[] = {
{
.name = "kernel",
@@ -89,7 +84,7 @@ static void __init rd88f6183ap_ge_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
- orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data);
+ orion5x_eth_switch_init(&rd88f6183ap_ge_switch_chip_data);
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 4dbcdbe1de7c..ac3376fc269f 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -124,7 +124,7 @@ static void __init wnr854t_init(void)
* Configure peripherals.
*/
orion5x_eth_init(&wnr854t_eth_data);
- orion5x_eth_switch_init(&wnr854t_switch_plat_data);
+ orion5x_eth_switch_init(&wnr854t_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index a6a8c4648d74..9250bb2e429c 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -191,11 +191,6 @@ static struct dsa_chip_data wrt350n_v2_switch_chip_data = {
.port_names[7] = "lan4",
};
-static struct dsa_platform_data __initdata wrt350n_v2_switch_plat_data = {
- .nr_chips = 1,
- .chip = &wrt350n_v2_switch_chip_data,
-};
-
static void __init wrt350n_v2_init(void)
{
/*
@@ -210,7 +205,7 @@ static void __init wrt350n_v2_init(void)
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
- orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data);
+ orion5x_eth_switch_init(&wrt350n_v2_switch_chip_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
diff --git a/arch/arm/plat-orion/common.c b/arch/arm/plat-orion/common.c
index 272f49b2c68f..9255b6d67ba5 100644
--- a/arch/arm/plat-orion/common.c
+++ b/arch/arm/plat-orion/common.c
@@ -22,6 +22,7 @@
#include <linux/platform_data/dma-mv_xor.h>
#include <linux/platform_data/usb-ehci-orion.h>
#include <plat/common.h>
+#include <linux/phy.h>
/* Create a clkdev entry for a given device/clk */
void __init orion_clkdev_add(const char *con_id, const char *dev_id,
@@ -470,15 +471,27 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
/*****************************************************************************
* Ethernet switch
****************************************************************************/
-void __init orion_ge00_switch_init(struct dsa_platform_data *d)
+static __initconst const char *orion_ge00_mvmdio_bus_name = "orion-mii";
+static __initdata struct mdio_board_info
+ orion_ge00_switch_board_info;
+
+void __init orion_ge00_switch_init(struct dsa_chip_data *d)
{
- int i;
+ struct mdio_board_info *bd;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(d->port_names); i++)
+ if (!strcmp(d->port_names[i], "cpu"))
+ break;
- d->netdev = &orion_ge00.dev;
- for (i = 0; i < d->nr_chips; i++)
- d->chip[i].host_dev = &orion_ge_mvmdio.dev;
+ bd = &orion_ge00_switch_board_info;
+ bd->bus_id = orion_ge00_mvmdio_bus_name;
+ bd->mdio_addr = d->sw_addr;
+ d->netdev[i] = &orion_ge00.dev;
+ strcpy(bd->modalias, "mv88e6085");
+ bd->platform_data = d;
- platform_device_register_data(NULL, "dsa", 0, d, sizeof(d));
+ mdiobus_register_board_info(&orion_ge00_switch_board_info, 1);
}
/*****************************************************************************
diff --git a/arch/arm/plat-orion/include/plat/common.h b/arch/arm/plat-orion/include/plat/common.h
index 9347f3c58a6d..3647d3b33c20 100644
--- a/arch/arm/plat-orion/include/plat/common.h
+++ b/arch/arm/plat-orion/include/plat/common.h
@@ -12,7 +12,7 @@
#include <linux/mv643xx_eth.h>
#include <linux/platform_data/usb-ehci-orion.h>
-struct dsa_platform_data;
+struct dsa_chip_data;
struct mv_sata_platform_data;
void __init orion_uart0_init(void __iomem *membase,
@@ -57,7 +57,7 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
unsigned long mapbase,
unsigned long irq);
-void __init orion_ge00_switch_init(struct dsa_platform_data *d);
+void __init orion_ge00_switch_init(struct dsa_chip_data *d);
void __init orion_i2c_init(unsigned long mapbase,
unsigned long irq,
--
2.9.3
^ permalink raw reply related [flat|nested] 22+ messages in thread