[RFC v2 1/5] ieee80211: add new VHT capability fields/parsing

[RFC v2 1/5] ieee80211: add new VHT capability fields/parsing

[Johannes Berg]

From: Johannes Berg <johannes.berg@intel.com>

IEEE 802.11-2016 extended the VHT capability fields to allow
indicating the number of spatial streams depending on the
actually used bandwidth, add support for decoding this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 include/linux/ieee80211.h |  35 ++++++++++++++-
 net/wireless/util.c       | 107 ++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 140 insertions(+), 2 deletions(-)

diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h
index 4a7200c6c9ea..aed8faaacc38 100644
--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -1457,13 +1457,16 @@ struct ieee80211_ht_operation {
  *	STA can receive. Rate expressed in units of 1 Mbps.
  *	If this field is 0 this value should not be used to
  *	consider the highest RX data rate supported.
- *	The top 3 bits of this field are reserved.
+ *	The top 3 bits of this field indicate the Maximum NSTS,total
+ *	(a beamformee capability.)
  * @tx_mcs_map: TX MCS map 2 bits for each stream, total 8 streams
  * @tx_highest: Indicates highest long GI VHT PPDU data rate
  *	STA can transmit. Rate expressed in units of 1 Mbps.
  *	If this field is 0 this value should not be used to
  *	consider the highest TX data rate supported.
- *	The top 3 bits of this field are reserved.
+ *	The top 2 bits of this field are reserved, the
+ *	3rd bit from the top indiciates VHT Extended NSS BW
+ *	Capability.
  */
 struct ieee80211_vht_mcs_info {
 	__le16 rx_mcs_map;
@@ -1472,6 +1475,13 @@ struct ieee80211_vht_mcs_info {
 	__le16 tx_highest;
 } __packed;
 
+/* for rx_highest */
+#define IEEE80211_VHT_MAX_NSTS_TOTAL_SHIFT	13
+#define IEEE80211_VHT_MAX_NSTS_TOTAL_MASK	(7 << IEEE80211_VHT_MAX_NSTS_TOTAL_SHIFT)
+
+/* for tx_highest */
+#define IEEE80211_VHT_EXT_NSS_BW_CAPABLE	(1 << 13)
+
 /**
  * enum ieee80211_vht_mcs_support - VHT MCS support definitions
  * @IEEE80211_VHT_MCS_SUPPORT_0_7: MCSes 0-7 are supported for the
@@ -1547,6 +1557,7 @@ struct ieee80211_vht_operation {
 #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ		0x00000004
 #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ	0x00000008
 #define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK			0x0000000C
+#define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_SHIFT			2
 #define IEEE80211_VHT_CAP_RXLDPC				0x00000010
 #define IEEE80211_VHT_CAP_SHORT_GI_80				0x00000020
 #define IEEE80211_VHT_CAP_SHORT_GI_160				0x00000040
@@ -1575,6 +1586,26 @@ struct ieee80211_vht_operation {
 #define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_MRQ_MFB	0x0c000000
 #define IEEE80211_VHT_CAP_RX_ANTENNA_PATTERN			0x10000000
 #define IEEE80211_VHT_CAP_TX_ANTENNA_PATTERN			0x20000000
+#define IEEE80211_VHT_CAP_EXT_NSS_BW_SHIFT			30
+#define IEEE80211_VHT_CAP_EXT_NSS_BW_MASK			0xc0000000
+
+/**
+ * ieee80211_get_vht_max_nss - return max NSS for a given bandwidth/MCS
+ * @cap: VHT capabilities of the peer
+ * @bw: bandwidth to use
+ * @mcs: MCS index to use
+ * @ext_nss_bw_capable: indicates whether or not the local transmitter
+ *	(rate scaling algorithm) can deal with the new logic
+ *	(dot11VHTExtendedNSSBWCapable)
+ *
+ * Due to the VHT Extended NSS Bandwidth Support, the maximum NSS can
+ * vary for a given BW/MCS. This function parses the data.
+ *
+ * Note: This function is exported by cfg80211.
+ */
+int ieee80211_get_vht_max_nss(struct ieee80211_vht_cap *cap,
+			      enum ieee80211_vht_chanwidth bw,
+			      int mcs, bool ext_nss_bw_capable);
 
 /* Authentication algorithms */
 #define WLAN_AUTH_OPEN 0
diff --git a/net/wireless/util.c b/net/wireless/util.c
index 23ee3d66dfe0..bc676d9b7e80 100644
--- a/net/wireless/util.c
+++ b/net/wireless/util.c
@@ -8,6 +8,7 @@
 #include <linux/bitops.h>
 #include <linux/etherdevice.h>
 #include <linux/slab.h>
+#include <linux/ieee80211.h>
 #include <net/cfg80211.h>
 #include <net/ip.h>
 #include <net/dsfield.h>
@@ -1874,3 +1875,109 @@ EXPORT_SYMBOL(rfc1042_header);
 const unsigned char bridge_tunnel_header[] __aligned(2) =
 	{ 0xaa, 0xaa, 0x03, 0x00, 0x00, 0xf8 };
 EXPORT_SYMBOL(bridge_tunnel_header);
+
+int ieee80211_get_vht_max_nss(struct ieee80211_vht_cap *cap,
+			      enum ieee80211_vht_chanwidth bw,
+			      int mcs, bool ext_nss_bw_capable)
+{
+	u16 map = le16_to_cpu(cap->supp_mcs.rx_mcs_map);
+	int max_vht_nss = 0;
+	int ext_nss_bw;
+	int supp_width;
+	int i, mcs_encoding;
+
+	if (map == 0xffff)
+		return 0;
+
+	if (WARN_ON(mcs > 9))
+		return 0;
+	if (mcs <= 7)
+		mcs_encoding = 0;
+	else if (mcs == 8)
+		mcs_encoding = 1;
+	else
+		mcs_encoding = 2;
+
+	/* find max_vht_nss for the given MCS */
+	for (i = 7; i >= 0; i--) {
+		int supp = (map >> (2*i)) & 3;
+
+		if (supp == 3)
+			continue;
+
+		if (supp >= mcs_encoding) {
+			max_vht_nss = i;
+			break;
+		}
+	}
+
+	if (!(cap->supp_mcs.tx_mcs_map & cpu_to_le16(IEEE80211_VHT_EXT_NSS_BW_CAPABLE)))
+		return max_vht_nss;
+
+	ext_nss_bw = (le32_to_cpu(cap->vht_cap_info) &
+					IEEE80211_VHT_CAP_EXT_NSS_BW_MASK)
+			>> IEEE80211_VHT_CAP_EXT_NSS_BW_SHIFT;
+	supp_width = (le32_to_cpu(cap->vht_cap_info) &
+					IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK)
+			>> IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_SHIFT;
+
+	/* if not capable, treat ext_nss_bw as 0 */
+	if (!ext_nss_bw_capable)
+		ext_nss_bw = 0;
+
+	/* This is invalid */
+	if (supp_width == 3)
+		return 0;
+
+	/* This is an invalid combination so pretend nothing is supported */
+	if (supp_width == 2 && (ext_nss_bw == 1 || ext_nss_bw == 2))
+		return 0;
+
+	/*
+	 * Cover all the special cases according to IEEE 802.11-2016 Table 9-250.
+	 * All other cases are either factor of 1 or not valid/supported.
+	 */
+	switch (bw) {
+	case IEEE80211_VHT_CHANWIDTH_USE_HT:
+	case IEEE80211_VHT_CHANWIDTH_80MHZ:
+		if ((supp_width == 1 || supp_width == 2) &&
+		    ext_nss_bw == 3)
+			return 2 * max_vht_nss;
+		break;
+	case IEEE80211_VHT_CHANWIDTH_160MHZ:
+		if (supp_width == 0 &&
+		    (ext_nss_bw == 1 || ext_nss_bw == 2))
+			return DIV_ROUND_UP(max_vht_nss, 2);
+		if (supp_width == 0 &&
+		    ext_nss_bw == 3)
+			return DIV_ROUND_UP(3 * max_vht_nss, 4);
+		if (supp_width == 1 &&
+		    ext_nss_bw == 3)
+			return 2 * max_vht_nss;
+		break;
+	case IEEE80211_VHT_CHANWIDTH_80P80MHZ:
+		if (supp_width == 0 &&
+		    (ext_nss_bw == 1 || ext_nss_bw == 2))
+			return 0; /* not possible */
+		if (supp_width == 0 &&
+		    ext_nss_bw == 2)
+			return DIV_ROUND_UP(max_vht_nss, 2);
+		if (supp_width == 0 &&
+		    ext_nss_bw == 3)
+			return DIV_ROUND_UP(3 * max_vht_nss, 4);
+		if (supp_width == 1 &&
+		    ext_nss_bw == 0)
+			return 0; /* not possible */
+		if (supp_width == 1 &&
+		    ext_nss_bw == 1)
+			return DIV_ROUND_UP(max_vht_nss, 2);
+		if (supp_width == 1 &&
+		    ext_nss_bw == 2)
+			return DIV_ROUND_UP(3 * max_vht_nss, 4);
+		break;
+	}
+
+	/* not covered or invalid combination received */
+	return max_vht_nss;
+}
+EXPORT_SYMBOL(ieee80211_get_vht_max_nss);
-- 
2.9.3

[RFC v2 2/5] mac80211: introduce capability flags for VHT EXT NSS support

[Johannes Berg]

From: Johannes Berg <johannes.berg@intel.com>

Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.

If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 include/net/mac80211.h     | 18 ++++++++++++++++
 net/mac80211/debugfs.c     |  1 +
 net/mac80211/ieee80211_i.h |  3 +++
 net/mac80211/main.c        | 52 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 74 insertions(+)

diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 3edb469a6de1..9017feff1784 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -2049,6 +2049,11 @@ struct ieee80211_txq {
  *	The stack will not do fragmentation.
  *	The callback for @set_frag_threshold should be set as well.
  *
+ * @IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW: (Hardware) rate control supports VHT
+ *	extended NSS BW (dot11VHTExtendedNSSBWCapable). This flag will be set if
+ *	the selected rate control algorithm sets %RATE_CTRL_CAPA_VHT_EXT_NSS_BW
+ *	but if the rate control is built-in then it must be set by the driver.
+ *
  * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
  */
 enum ieee80211_hw_flags {
@@ -2091,6 +2096,7 @@ enum ieee80211_hw_flags {
 	IEEE80211_HW_TX_FRAG_LIST,
 	IEEE80211_HW_REPORTS_LOW_ACK,
 	IEEE80211_HW_SUPPORTS_TX_FRAG,
+	IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW,
 
 	/* keep last, obviously */
 	NUM_IEEE80211_HW_FLAGS
@@ -5464,7 +5470,19 @@ struct ieee80211_tx_rate_control {
 	bool bss;
 };
 
+/**
+ * enum rate_control_capabilities - rate control capabilities
+ */
+enum rate_control_capabilities {
+	/**
+	 * @RATE_CTRL_CAPA_VHT_EXT_NSS_BW:
+	 *	support for extended NSS BW support (dot11VHTExtendedNSSCapable)
+	 */
+	RATE_CTRL_CAPA_VHT_EXT_NSS_BW = BIT(0),
+};
+
 struct rate_control_ops {
+	unsigned long capa;
 	const char *name;
 	void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
 	void (*free)(void *priv);
diff --git a/net/mac80211/debugfs.c b/net/mac80211/debugfs.c
index 5fae001f286c..a431514ea01c 100644
--- a/net/mac80211/debugfs.c
+++ b/net/mac80211/debugfs.c
@@ -211,6 +211,7 @@ static const char *hw_flag_names[] = {
 	FLAG(TX_FRAG_LIST),
 	FLAG(REPORTS_LOW_ACK),
 	FLAG(SUPPORTS_TX_FRAG),
+	FLAG(SUPPORTS_VHT_EXT_NSS_BW),
 #undef FLAG
 };
 
diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 159a1a733725..4047fc528977 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -1217,6 +1217,9 @@ struct ieee80211_local {
 	/* number of RX chains the hardware has */
 	u8 rx_chains;
 
+	/* bitmap of which sbands were copied */
+	u8 sband_allocated;
+
 	int tx_headroom; /* required headroom for hardware/radiotap */
 
 	/* Tasklet and skb queue to process calls from IRQ mode. All frames
diff --git a/net/mac80211/main.c b/net/mac80211/main.c
index 56fb47953b72..b83a1e2ba002 100644
--- a/net/mac80211/main.c
+++ b/net/mac80211/main.c
@@ -1095,6 +1095,51 @@ int ieee80211_register_hw(struct ieee80211_hw *hw)
 		goto fail_rate;
 	}
 
+	if (local->rate_ctrl) {
+		clear_bit(IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW, hw->flags);
+		if (local->rate_ctrl->ops->capa & RATE_CTRL_CAPA_VHT_EXT_NSS_BW)
+			ieee80211_hw_set(hw, SUPPORTS_VHT_EXT_NSS_BW);
+	}
+
+	/*
+	 * If the VHT capabilities don't have IEEE80211_VHT_EXT_NSS_BW_CAPABLE,
+	 * or have it when we don't, copy the sband structure and set/clear it.
+	 * This is necessary because rate scaling algorithms could be switched
+	 * and have different support values.
+	 * Print a message so that in the common case the reallocation can be
+	 * avoided.
+	 */
+	BUILD_BUG_ON(NUM_NL80211_BANDS > 8 * sizeof(local->sband_allocated));
+	for (band = 0; band < NUM_NL80211_BANDS; band++) {
+		struct ieee80211_supported_band *sband;
+		bool local_cap, ie_cap;
+
+		local_cap = ieee80211_hw_check(hw, SUPPORTS_VHT_EXT_NSS_BW);
+
+		sband = local->hw.wiphy->bands[band];
+		if (!sband || !sband->vht_cap.vht_supported)
+			continue;
+
+		ie_cap = !!(sband->vht_cap.vht_mcs.tx_highest &
+			    cpu_to_le16(IEEE80211_VHT_EXT_NSS_BW_CAPABLE));
+
+		if (local_cap == ie_cap)
+			continue;
+
+		sband = kmemdup(sband, sizeof(*sband), GFP_KERNEL);
+		if (!sband)
+			goto fail_rate;
+
+		wiphy_dbg(hw->wiphy, "copying sband (band %d) due to VHT EXT NSS BW flag\n",
+			  band);
+
+		sband->vht_cap.vht_mcs.tx_highest ^=
+			cpu_to_le16(IEEE80211_VHT_EXT_NSS_BW_CAPABLE);
+
+		local->hw.wiphy->bands[band] = sband;
+		local->sband_allocated |= BIT(band);
+	}
+
 	/* add one default STA interface if supported */
 	if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_STATION) &&
 	    !ieee80211_hw_check(hw, NO_AUTO_VIF)) {
@@ -1216,6 +1261,7 @@ static int ieee80211_free_ack_frame(int id, void *p, void *data)
 void ieee80211_free_hw(struct ieee80211_hw *hw)
 {
 	struct ieee80211_local *local = hw_to_local(hw);
+	enum nl80211_band band;
 
 	mutex_destroy(&local->iflist_mtx);
 	mutex_destroy(&local->mtx);
@@ -1231,6 +1277,12 @@ void ieee80211_free_hw(struct ieee80211_hw *hw)
 
 	ieee80211_free_led_names(local);
 
+	for (band = 0; band < NUM_NL80211_BANDS; band++) {
+		if (!(local->sband_allocated & BIT(band)))
+			continue;
+		kfree(local->hw.wiphy->bands[band]);
+	}
+
 	wiphy_free(local->hw.wiphy);
 }
 EXPORT_SYMBOL(ieee80211_free_hw);
-- 
2.9.3

[RFC v2 3/5] mac80211: add ability to parse CCFS2

[Johannes Berg]

From: Johannes Berg <johannes.berg@intel.com>

With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 net/mac80211/ibss.c        |  4 +++-
 net/mac80211/ieee80211_i.h |  4 +++-
 net/mac80211/mesh.c        |  4 +++-
 net/mac80211/mlme.c        |  3 ++-
 net/mac80211/spectmgmt.c   |  5 ++++-
 net/mac80211/util.c        | 48 ++++++++++++++++++++++++++++++----------------
 6 files changed, 47 insertions(+), 21 deletions(-)

diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index 98999d3d5262..a5c0c5818da5 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -1065,7 +1065,9 @@ static void ieee80211_update_sta_info(struct ieee80211_sub_if_data *sdata,
 			struct ieee80211_vht_cap cap_ie;
 			struct ieee80211_sta_vht_cap cap = sta->sta.vht_cap;
 
-			ieee80211_chandef_vht_oper(elems->vht_operation,
+			ieee80211_chandef_vht_oper(&local->hw,
+						   elems->vht_operation,
+						   elems->ht_operation,
 						   &chandef);
 			memcpy(&cap_ie, elems->vht_cap_elem, sizeof(cap_ie));
 			ieee80211_vht_cap_ie_to_sta_vht_cap(sdata, sband,
diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 4047fc528977..b0690c2d7f7d 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -2074,7 +2074,9 @@ u8 *ieee80211_add_wmm_info_ie(u8 *buf, u8 qosinfo);
 /* channel management */
 bool ieee80211_chandef_ht_oper(const struct ieee80211_ht_operation *ht_oper,
 			       struct cfg80211_chan_def *chandef);
-bool ieee80211_chandef_vht_oper(const struct ieee80211_vht_operation *oper,
+bool ieee80211_chandef_vht_oper(struct ieee80211_hw *hw,
+				const struct ieee80211_vht_operation *oper,
+				const struct ieee80211_ht_operation *htop,
 				struct cfg80211_chan_def *chandef);
 u32 ieee80211_chandef_downgrade(struct cfg80211_chan_def *c);
 
diff --git a/net/mac80211/mesh.c b/net/mac80211/mesh.c
index c28b0af9c1f2..1b60b4350517 100644
--- a/net/mac80211/mesh.c
+++ b/net/mac80211/mesh.c
@@ -92,7 +92,9 @@ bool mesh_matches_local(struct ieee80211_sub_if_data *sdata,
 	cfg80211_chandef_create(&sta_chan_def, sdata->vif.bss_conf.chandef.chan,
 				NL80211_CHAN_NO_HT);
 	ieee80211_chandef_ht_oper(ie->ht_operation, &sta_chan_def);
-	ieee80211_chandef_vht_oper(ie->vht_operation, &sta_chan_def);
+	ieee80211_chandef_vht_oper(&sdata->local->hw,
+				   ie->vht_operation, ie->ht_operation,
+				   &sta_chan_def);
 
 	if (!cfg80211_chandef_compatible(&sdata->vif.bss_conf.chandef,
 					 &sta_chan_def))
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index 23986934d7af..2ff3040ebb09 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -213,7 +213,8 @@ ieee80211_determine_chantype(struct ieee80211_sub_if_data *sdata,
 	}
 
 	vht_chandef = *chandef;
-	if (!ieee80211_chandef_vht_oper(vht_oper, &vht_chandef)) {
+	if (!ieee80211_chandef_vht_oper(&sdata->local->hw,
+					vht_oper, ht_oper, &vht_chandef)) {
 		if (!(ifmgd->flags & IEEE80211_STA_DISABLE_VHT))
 			sdata_info(sdata,
 				   "AP VHT information is invalid, disable VHT\n");
diff --git a/net/mac80211/spectmgmt.c b/net/mac80211/spectmgmt.c
index 0782e486fe89..5a013b53b4f0 100644
--- a/net/mac80211/spectmgmt.c
+++ b/net/mac80211/spectmgmt.c
@@ -138,6 +138,7 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
 				wide_bw_chansw_ie->new_center_freq_seg1,
 			/* .basic_mcs_set doesn't matter */
 		};
+		struct ieee80211_ht_operation ht_oper = {};
 
 		/* default, for the case of IEEE80211_VHT_CHANWIDTH_USE_HT,
 		 * to the previously parsed chandef
@@ -145,7 +146,9 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
 		new_vht_chandef = csa_ie->chandef;
 
 		/* ignore if parsing fails */
-		if (!ieee80211_chandef_vht_oper(&vht_oper, &new_vht_chandef))
+		if (!ieee80211_chandef_vht_oper(&sdata->local->hw,
+						&vht_oper, &ht_oper,
+						&new_vht_chandef))
 			new_vht_chandef.chan = NULL;
 
 		if (sta_flags & IEEE80211_STA_DISABLE_80P80MHZ &&
diff --git a/net/mac80211/util.c b/net/mac80211/util.c
index 7a37ce78bb38..152aae54b67f 100644
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@ -2482,49 +2482,65 @@ bool ieee80211_chandef_ht_oper(const struct ieee80211_ht_operation *ht_oper,
 	return true;
 }
 
-bool ieee80211_chandef_vht_oper(const struct ieee80211_vht_operation *oper,
+bool ieee80211_chandef_vht_oper(struct ieee80211_hw *hw,
+				const struct ieee80211_vht_operation *oper,
+				const struct ieee80211_ht_operation *htop,
 				struct cfg80211_chan_def *chandef)
 {
 	struct cfg80211_chan_def new = *chandef;
-	int cf1, cf2;
+	int cf0, cf1;
+	int ccfs0, ccfs1, ccfs2;
+	int ccf0, ccf1;
 
-	if (!oper)
+	if (!oper || !htop)
 		return false;
 
-	cf1 = ieee80211_channel_to_frequency(oper->center_freq_seg0_idx,
-					     chandef->chan->band);
-	cf2 = ieee80211_channel_to_frequency(oper->center_freq_seg1_idx,
-					     chandef->chan->band);
+	ccfs0 = oper->center_freq_seg0_idx;
+	ccfs1 = oper->center_freq_seg1_idx;
+	ccfs2 = (le16_to_cpu(htop->operation_mode) &
+				IEEE80211_HT_OP_MODE_CCFS2_MASK)
+			>> IEEE80211_HT_OP_MODE_CCFS2_SHIFT;
+
+	/* when parsing (and we know how to) CCFS1 and CCFS2 are equivalent */
+	ccf0 = ccfs0;
+	ccf1 = ccfs1;
+	if (!ccfs1 && ieee80211_hw_check(hw, SUPPORTS_VHT_EXT_NSS_BW))
+		ccf1 = ccfs2;
+
+	cf0 = ieee80211_channel_to_frequency(ccf0, chandef->chan->band);
+	cf1 = ieee80211_channel_to_frequency(ccf1, chandef->chan->band);
 
 	switch (oper->chan_width) {
 	case IEEE80211_VHT_CHANWIDTH_USE_HT:
+		/* just use HT information directly */
 		break;
 	case IEEE80211_VHT_CHANWIDTH_80MHZ:
 		new.width = NL80211_CHAN_WIDTH_80;
-		new.center_freq1 = cf1;
+		new.center_freq1 = cf0;
 		/* If needed, adjust based on the newer interop workaround. */
-		if (oper->center_freq_seg1_idx) {
+		if (ccf1) {
 			unsigned int diff;
 
-			diff = abs(oper->center_freq_seg1_idx -
-				   oper->center_freq_seg0_idx);
+			diff = abs(ccf1 - ccf0);
 			if (diff == 8) {
 				new.width = NL80211_CHAN_WIDTH_160;
-				new.center_freq1 = cf2;
+				new.center_freq1 = cf1;
 			} else if (diff > 8) {
 				new.width = NL80211_CHAN_WIDTH_80P80;
-				new.center_freq2 = cf2;
+				new.center_freq2 = cf1;
 			}
 		}
 		break;
 	case IEEE80211_VHT_CHANWIDTH_160MHZ:
+		/* deprecated encoding */
 		new.width = NL80211_CHAN_WIDTH_160;
-		new.center_freq1 = cf1;
+		new.center_freq1 = cf0;
 		break;
 	case IEEE80211_VHT_CHANWIDTH_80P80MHZ:
+		/* deprecated encoding */
 		new.width = NL80211_CHAN_WIDTH_80P80;
-		new.center_freq1 = cf1;
-		new.center_freq2 = cf2;
+		new.center_freq1 = cf0;
+		new.center_freq2 = cf1;
 		break;
 	default:
 		return false;
-- 
2.9.3

[RFC v2 4/5] mac80211: copy VHT EXT NSS BW Support/Capable data to station

[Johannes Berg]

From: Johannes Berg <johannes.berg@intel.com>

When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.

Also, since it was missing, copy tx_highest and rx_highest.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 net/mac80211/vht.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/net/mac80211/vht.c b/net/mac80211/vht.c
index 19ec2189d3ac..2d1e72747ab8 100644
--- a/net/mac80211/vht.c
+++ b/net/mac80211/vht.c
@@ -231,6 +231,13 @@ ieee80211_vht_cap_ie_to_sta_vht_cap(struct ieee80211_sub_if_data *sdata,
 	memcpy(&vht_cap->vht_mcs, &vht_cap_ie->supp_mcs,
 	       sizeof(struct ieee80211_vht_mcs_info));
 
+	/* copy EXT_NSS_BW Support value or remove the capability */
+	if (ieee80211_hw_check(&sdata->local->hw, SUPPORTS_VHT_EXT_NSS_BW))
+		vht_cap->cap |= (cap_info & IEEE80211_VHT_CAP_EXT_NSS_BW_MASK);
+	else
+		vht_cap->vht_mcs.tx_highest &=
+			~cpu_to_le16(IEEE80211_VHT_EXT_NSS_BW_CAPABLE);
+
 	/* but also restrict MCSes */
 	for (i = 0; i < 8; i++) {
 		u16 own_rx, own_tx, peer_rx, peer_tx;
@@ -294,6 +301,18 @@ ieee80211_vht_cap_ie_to_sta_vht_cap(struct ieee80211_sub_if_data *sdata,
 		break;
 	default:
 		sta->cur_max_bandwidth = IEEE80211_STA_RX_BW_80;
+
+		if (!(vht_cap->vht_mcs.tx_highest &
+				cpu_to_le16(IEEE80211_VHT_EXT_NSS_BW_CAPABLE))
+			break;
+
+		/*
+		 * If this is non-zero, then it does support 160 MHz after all,
+		 * in one form or the other. We don't distinguish here (or even
+		 * above) between 160 and 80+80 yet.
+		 */
+		if (cap_info & IEEE80211_VHT_CAP_EXT_NSS_BW_MASK)
+			sta->cur_max_bandwidth = IEEE80211_STA_RX_BW_160;
 	}
 
 	sta->sta.bandwidth = ieee80211_sta_cur_vht_bw(sta);
-- 
2.9.3

[RFC v2 5/5] cfg80211: add support for HE MCSs

[Johannes Berg]

From: Johannes Berg <johannes.berg@intel.com>

Add support for the HE MCSs in cfg80211 and also add userspace
API to nl80211 to send rate information out.

The bandwidth calculation is somewhat approximate to avoid all
the big tables that are otherwise necessary.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 include/net/cfg80211.h       | 15 +++++++--
 include/uapi/linux/nl80211.h | 42 +++++++++++++++++++++++
 net/wireless/nl80211.c       | 16 +++++++++
 net/wireless/util.c          | 80 ++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 151 insertions(+), 2 deletions(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 86c12f85fb53..48af8d6b4fc7 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -986,12 +986,14 @@ int cfg80211_check_station_change(struct wiphy *wiphy,
  * @RATE_INFO_FLAGS_VHT_MCS: mcs field filled with VHT MCS
  * @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
  * @RATE_INFO_FLAGS_60G: 60GHz MCS
+ * @RATE_INFO_FLAGS_HE_MCS: HE MCS information
  */
 enum rate_info_flags {
 	RATE_INFO_FLAGS_MCS			= BIT(0),
 	RATE_INFO_FLAGS_VHT_MCS			= BIT(1),
 	RATE_INFO_FLAGS_SHORT_GI		= BIT(2),
 	RATE_INFO_FLAGS_60G			= BIT(3),
+	RATE_INFO_FLAGS_HE_MCS			= BIT(4),
 };
 
 /**
@@ -1005,6 +1007,7 @@ enum rate_info_flags {
  * @RATE_INFO_BW_40: 40 MHz bandwidth
  * @RATE_INFO_BW_80: 80 MHz bandwidth
  * @RATE_INFO_BW_160: 160 MHz bandwidth
+ * @RATE_INFO_BW_HE_RU: bandwidth determined by HE RU allocation
  */
 enum rate_info_bw {
 	RATE_INFO_BW_5,
@@ -1013,6 +1016,7 @@ enum rate_info_bw {
 	RATE_INFO_BW_40,
 	RATE_INFO_BW_80,
 	RATE_INFO_BW_160,
+	RATE_INFO_BW_HE_RU,
 };
 
 /**
@@ -1021,10 +1025,14 @@ enum rate_info_bw {
  * Information about a receiving or transmitting bitrate
  *
  * @flags: bitflag of flags from &enum rate_info_flags
- * @mcs: mcs index if struct describes a 802.11n bitrate
+ * @mcs: mcs index if struct describes an HT/VHT/HE rate
  * @legacy: bitrate in 100kbit/s for 802.11abg
- * @nss: number of streams (VHT only)
+ * @nss: number of streams (VHT & HE only)
  * @bw: bandwidth (from &enum rate_info_bw)
+ * @he_gi: HE guard interval (from &enum nl80211_he_gi)
+ * @he_dcm: HE DCM value
+ * @he_ru_alloc: HE RU allocation (from &enum nl80211_he_ru_alloc,
+ *	only valid if bw is %RATE_INFO_BW_HE_RU)
  */
 struct rate_info {
 	u8 flags;
@@ -1032,6 +1040,9 @@ struct rate_info {
 	u16 legacy;
 	u8 nss;
 	u8 bw;
+	u8 he_gi;
+	u8 he_dcm;
+	u8 he_ru_alloc;
 };
 
 /**
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 9a499b15cfbc..f2b577dbaca0 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -2598,6 +2598,36 @@ struct nl80211_sta_flag_update {
 } __attribute__((packed));
 
 /**
+ * enum nl80211_he_gi - HE guard interval
+ * @NL80211_RATE_INFO_HE_GI_0_8: 0.8 usec
+ * @NL80211_RATE_INFO_HE_GI_1_6: 1.6 usec
+ * @NL80211_RATE_INFO_HE_GI_3_2: 3.2 usec
+ */
+enum nl80211_he_gi {
+	NL80211_RATE_INFO_HE_GI_0_8,
+	NL80211_RATE_INFO_HE_GI_1_6,
+	NL80211_RATE_INFO_HE_GI_3_2,
+};
+
+/**
+ * @enum nl80211_he_ru_alloc - HE RU allocation values
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_52: 52-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_106: 106-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_242: 242-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_484: 484-tone RU allocation
+ * @NL80211_RATE_INFO_HE_RU_ALLOC_969: 969-tone RU allocation
+ */
+enum nl80211_he_ru_alloc {
+	NL80211_RATE_INFO_HE_RU_ALLOC_26,
+	NL80211_RATE_INFO_HE_RU_ALLOC_52,
+	NL80211_RATE_INFO_HE_RU_ALLOC_106,
+	NL80211_RATE_INFO_HE_RU_ALLOC_242,
+	NL80211_RATE_INFO_HE_RU_ALLOC_484,
+	NL80211_RATE_INFO_HE_RU_ALLOC_969,
+};
+
+/**
  * enum nl80211_rate_info - bitrate information
  *
  * These attribute types are used with %NL80211_STA_INFO_TXRATE
@@ -2629,6 +2659,13 @@ struct nl80211_sta_flag_update {
  * @NL80211_RATE_INFO_5_MHZ_WIDTH: 5 MHz width - note that this is
  *	a legacy rate and will be reported as the actual bitrate, i.e.
  *	a quarter of the base (20 MHz) rate
+ * @NL80211_RATE_INFO_HE_MCS: HE MCS index (u8, 0-11)
+ * @NL80211_RATE_INFO_HE_NSS: HE NSS value (u8, 1-8)
+ * @NL80211_RATE_INFO_HE_GI: HE guard interval identifier
+ *	(u8, see &enum nl80211_he_gi)
+ * @NL80211_RATE_INFO_HE_DCM: HE DCM value (u8, 0/1)
+ * @NL80211_RATE_INFO_RU_ALLOC: HE RU allocation, if not present then
+ *	non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc)
  * @__NL80211_RATE_INFO_AFTER_LAST: internal use
  */
 enum nl80211_rate_info {
@@ -2645,6 +2682,11 @@ enum nl80211_rate_info {
 	NL80211_RATE_INFO_160_MHZ_WIDTH,
 	NL80211_RATE_INFO_10_MHZ_WIDTH,
 	NL80211_RATE_INFO_5_MHZ_WIDTH,
+	NL80211_RATE_INFO_HE_MCS,
+	NL80211_RATE_INFO_HE_NSS,
+	NL80211_RATE_INFO_HE_GI,
+	NL80211_RATE_INFO_HE_DCM,
+	NL80211_RATE_INFO_HE_RU_ALLOC,
 
 	/* keep last */
 	__NL80211_RATE_INFO_AFTER_LAST,
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index d516527fcb8e..e779733143b8 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -4204,6 +4204,9 @@ static bool nl80211_put_sta_rate(struct sk_buff *msg, struct rate_info *info,
 	case RATE_INFO_BW_160:
 		rate_flg = NL80211_RATE_INFO_160_MHZ_WIDTH;
 		break;
+	case RATE_INFO_BW_HE_RU:
+		rate_flg = 0;
+		WARN_ON(!(info->flags & RATE_INFO_FLAGS_HE_MCS));
 	}
 
 	if (rate_flg && nla_put_flag(msg, rate_flg))
@@ -4223,6 +4226,19 @@ static bool nl80211_put_sta_rate(struct sk_buff *msg, struct rate_info *info,
 		if (info->flags & RATE_INFO_FLAGS_SHORT_GI &&
 		    nla_put_flag(msg, NL80211_RATE_INFO_SHORT_GI))
 			return false;
+	} else if (info->flags & RATE_INFO_FLAGS_HE_MCS) {
+		if (nla_put_u8(msg, NL80211_RATE_INFO_HE_MCS, info->mcs))
+			return false;
+		if (nla_put_u8(msg, NL80211_RATE_INFO_HE_NSS, info->nss))
+			return false;
+		if (nla_put_u8(msg, NL80211_RATE_INFO_HE_GI, info->he_gi))
+			return false;
+		if (nla_put_u8(msg, NL80211_RATE_INFO_HE_DCM, info->he_dcm))
+			return false;
+		if (info->bw == RATE_INFO_BW_HE_RU &&
+		    nla_put_u8(msg, NL80211_RATE_INFO_HE_RU_ALLOC,
+			       info->he_ru_alloc))
+			return false;
 	}
 
 	nla_nest_end(msg, rate);
diff --git a/net/wireless/util.c b/net/wireless/util.c
index bc676d9b7e80..967fc20e10f2 100644
--- a/net/wireless/util.c
+++ b/net/wireless/util.c
@@ -1258,6 +1258,84 @@ static u32 cfg80211_calculate_bitrate_vht(struct rate_info *rate)
 	return (bitrate + 50000) / 100000;
 }
 
+static u32 cfg80211_calculate_bitrate_he(struct rate_info *rate)
+{
+#define SCALE 2048
+	u16 mcs_divisors[12] = {
+		34133, /* 16.666666... */
+		17067, /*  8.333333... */
+		11378, /*  5.555555... */
+		 8533, /*  4.166666... */
+		 5689, /*  2.777777... */
+		 4267, /*  2.083333... */
+		 3923, /*  1.851851... */
+		 3413, /*  1.666666... */
+		 2844, /*  1.388888... */
+		 2560, /*  1.250000... */
+		 2276, /*  1.111111... */
+		 2048, /*  1.000000... */
+	};
+	u32 rates_160M[3] = { 960777777, 907400000, 816666666 };
+	u32 rates_969[3] =  { 480388888, 453700000, 408333333 };
+	u32 rates_484[3] =  { 229411111, 216666666, 195000000 };
+	u32 rates_242[3] =  { 114711111, 108333333,  97500000 };
+	u32 rates_106[3] =  {  40000000,  37777777,  34000000 };
+	u32 rates_52[3]  =  {  18820000,  17777777,  16000000 };
+	u32 rates_26[3]  =  {   9411111,   8888888,   8000000 };
+	u64 tmp;
+	u32 result;
+
+	if (WARN_ON_ONCE(rate->mcs > 11))
+		return 0;
+
+	if (WARN_ON_ONCE(rate->he_gi > NL80211_RATE_INFO_HE_GI_3_2))
+		return 0;
+	if (WARN_ON_ONCE(rate->he_ru_alloc > NL80211_RATE_INFO_HE_RU_ALLOC_969))
+		return 0;
+	if (WARN_ON_ONCE(rate->nss < 1 || rate->nss > 8))
+		return 0;
+
+	if (rate->bw == RATE_INFO_BW_160)
+		result = rates_160M[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_80 ||
+		 (rate->bw == RATE_INFO_BW_HE_RU &&
+		  rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_969))
+		result = rates_969[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_40 ||
+		 (rate->bw == RATE_INFO_BW_HE_RU &&
+		  rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_484))
+		result = rates_484[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_20 ||
+		 (rate->bw == RATE_INFO_BW_HE_RU &&
+		  rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_242))
+		result = rates_242[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_HE_RU &&
+		 rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_106)
+		result = rates_106[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_HE_RU &&
+		 rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_52)
+		result = rates_52[rate->he_gi];
+	else if (rate->bw == RATE_INFO_BW_HE_RU &&
+		 rate->he_ru_alloc == NL80211_RATE_INFO_HE_RU_ALLOC_26)
+		result = rates_26[rate->he_gi];
+	else if (WARN(1, "invalid HE MCS: bw:%d, ru:%d\n",
+		      rate->bw, rate->he_ru_alloc))
+		result = 0;
+
+	/* now scale to the appropriate MCS */
+	tmp = result;
+	tmp *= SCALE;
+	do_div(tmp, mcs_divisors[rate->mcs]);
+	result = tmp;
+
+	/* and take MCS, DCM into account */
+	result = (result / 8) * rate->nss;
+	if (rate->he_dcm)
+		result /= 2;
+
+	return result;
+}
+
 u32 cfg80211_calculate_bitrate(struct rate_info *rate)
 {
 	if (rate->flags & RATE_INFO_FLAGS_MCS)
@@ -1266,6 +1344,8 @@ u32 cfg80211_calculate_bitrate(struct rate_info *rate)
 		return cfg80211_calculate_bitrate_60g(rate);
 	if (rate->flags & RATE_INFO_FLAGS_VHT_MCS)
 		return cfg80211_calculate_bitrate_vht(rate);
+	if (rate->flags & RATE_INFO_FLAGS_HE_MCS)
+		return cfg80211_calculate_bitrate_he(rate);
 
 	return rate->legacy;
 }
-- 
2.9.3