* [PATCH v6 0/4] Allwinner H5 and Orange Pi PC2 support
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3, and it's pin-to-pin compatible with H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Several H5 boards by Sinovoip Banana Pi and FriendlyARM Nano Pi
are coming, so we should get ready for them.
The rename of sun8i-h3-ccu driver is dropped in this version,
according to the recommendation by Maxime Ripard.
This patchset depends on patchset [1] to finally take effect. At
least the patch 1 of that patchset is needed if you want to test
the kernel image -- without it the pinctrl driver won't be built
and the kernel will become unusable without pinctrl.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490780.html
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (1):
clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 602 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 586 ++++++++++++++++++++
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
12 files changed, 1247 insertions(+), 573 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
--
2.11.1
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v6 0/4] Allwinner H5 and Orange Pi PC2 support
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3, and it's pin-to-pin compatible with H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Several H5 boards by Sinovoip Banana Pi and FriendlyARM Nano Pi
are coming, so we should get ready for them.
The rename of sun8i-h3-ccu driver is dropped in this version,
according to the recommendation by Maxime Ripard.
This patchset depends on patchset [1] to finally take effect. At
least the patch 1 of that patchset is needed if you want to test
the kernel image -- without it the pinctrl driver won't be built
and the kernel will become unusable without pinctrl.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490780.html
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (1):
clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 602 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 586 ++++++++++++++++++++
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
12 files changed, 1247 insertions(+), 573 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v6 0/4] Allwinner H5 and Orange Pi PC2 support
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3, and it's pin-to-pin compatible with H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Several H5 boards by Sinovoip Banana Pi and FriendlyARM Nano Pi
are coming, so we should get ready for them.
The rename of sun8i-h3-ccu driver is dropped in this version,
according to the recommendation by Maxime Ripard.
This patchset depends on patchset [1] to finally take effect. At
least the patch 1 of that patchset is needed if you want to test
the kernel image -- without it the pinctrl driver won't be built
and the kernel will become unusable without pinctrl.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490780.html
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (1):
clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
arch/arm/boot/dts/sun8i-h3.dtsi | 602 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 586 ++++++++++++++++++++
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
12 files changed, 1247 insertions(+), 573 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
--
2.11.1
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
2017-03-01 20:13 ` Icenowy Zheng
(?)
@ 2017-03-01 20:13 ` Icenowy Zheng
-1 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
The rename of ccu-sun8i-h3 driver is dropped according to the
recommendation by Maxime Ripard, which saved me 2 commits ;-)
Users of H3 device tree binding header may find the *_BUS_SCR is changed
to *_BUS_SCR0, but I'm sure that currently there won't be mainline device
tree that uses this gate/reset, as there's no driver for it.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
6 files changed, 332 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..7013c205d0e8 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
index a26c8a19fe93..4cbc1b701b7c 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -546,7 +548,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -677,7 +787,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -727,7 +837,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
};
static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
@@ -790,7 +1016,71 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+};
+
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
@@ -803,6 +1093,16 @@ static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
.num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
};
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
+};
+
static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
@@ -810,7 +1110,8 @@ static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -827,10 +1128,22 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
val &= ~GENMASK(19, 16);
writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
&sun8i_h3_cpu_nb);
}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
+}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
index 78be712c7487..85973d1e8165 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index efb7ba2bd515..c2afc41d6964 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
index 6b7af80c26ec..484c2a22919d 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -98,6 +98,9 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
The rename of ccu-sun8i-h3 driver is dropped according to the
recommendation by Maxime Ripard, which saved me 2 commits ;-)
Users of H3 device tree binding header may find the *_BUS_SCR is changed
to *_BUS_SCR0, but I'm sure that currently there won't be mainline device
tree that uses this gate/reset, as there's no driver for it.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
6 files changed, 332 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..7013c205d0e8 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
index a26c8a19fe93..4cbc1b701b7c 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -546,7 +548,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -677,7 +787,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -727,7 +837,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
};
static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
@@ -790,7 +1016,71 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+};
+
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
@@ -803,6 +1093,16 @@ static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
.num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
};
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
+};
+
static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
@@ -810,7 +1110,8 @@ static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -827,10 +1128,22 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
val &= ~GENMASK(19, 16);
writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
&sun8i_h3_cpu_nb);
}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
+}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
index 78be712c7487..85973d1e8165 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index efb7ba2bd515..c2afc41d6964 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
index 6b7af80c26ec..484c2a22919d 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -98,6 +98,9 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
The rename of ccu-sun8i-h3 driver is dropped according to the
recommendation by Maxime Ripard, which saved me 2 commits ;-)
Users of H3 device tree binding header may find the *_BUS_SCR is changed
to *_BUS_SCR0, but I'm sure that currently there won't be mainline device
tree that uses this gate/reset, as there's no driver for it.
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun8i-h3.c | 327 ++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun8i-h3.h | 3 +-
include/dt-bindings/clock/sun8i-h3-ccu.h | 5 +-
include/dt-bindings/reset/sun8i-h3-ccu.h | 5 +-
6 files changed, 332 insertions(+), 11 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index bae5668cf427..68512aa398a9 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -10,6 +10,7 @@ Required properties :
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
+ - "allwinner,sun50i-h5-ccu"
- reg: Must contain the registers base address and length
- clocks: phandle to the oscillators feeding the CCU. Two are needed:
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 695bbf9ef428..7013c205d0e8 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -118,7 +118,7 @@ config SUN8I_H3_CCU
select SUNXI_CCU_NM
select SUNXI_CCU_MP
select SUNXI_CCU_PHASE
- default MACH_SUN8I
+ default MACH_SUN8I || (ARM64 && ARCH_SUNXI)
config SUN8I_V3S_CCU
bool "Support for the Allwinner V3s CCU"
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
index a26c8a19fe93..4cbc1b701b7c 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.c
@@ -300,8 +300,10 @@ static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
0x06c, BIT(18), 0);
static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
0x06c, BIT(19), 0);
-static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+static SUNXI_CCU_GATE(bus_scr0_clk, "bus-scr0", "apb2",
0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_scr1_clk, "bus-scr1", "apb2",
+ 0x06c, BIT(21), 0);
static SUNXI_CCU_GATE(bus_ephy_clk, "bus-ephy", "ahb1",
0x070, BIT(0), 0);
@@ -546,7 +548,7 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&bus_uart1_clk.common,
&bus_uart2_clk.common,
&bus_uart3_clk.common,
- &bus_scr_clk.common,
+ &bus_scr0_clk.common,
&bus_ephy_clk.common,
&bus_dbg_clk.common,
&ths_clk.common,
@@ -597,6 +599,114 @@ static struct ccu_common *sun8i_h3_ccu_clks[] = {
&gpu_clk.common,
};
+static struct ccu_common *sun50i_h5_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_clk.common,
+ &pll_periph0_clk.common,
+ &pll_gpu_clk.common,
+ &pll_periph1_clk.common,
+ &pll_de_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &ahb2_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ve_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi_clk.common,
+ &bus_tve_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_gpu_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_pio_clk.common,
+ &bus_ths_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_scr0_clk.common,
+ &bus_scr1_clk.common,
+ &bus_ephy_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &spdif_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_phy3_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci3_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_deinterlace_clk.common,
+ &dram_ts_clk.common,
+ &de_clk.common,
+ &tcon_clk.common,
+ &tve_clk.common,
+ &deinterlace_clk.common,
+ &csi_misc_clk.common,
+ &csi_sclk_clk.common,
+ &csi_mclk_clk.common,
+ &ve_clk.common,
+ &ac_dig_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_ddc_clk.common,
+ &mbus_clk.common,
+ &gpu_clk.common,
+};
+
/* We hardcode the divider to 4 for now */
static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
"pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
@@ -677,7 +787,7 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
[CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
[CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
- [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
[CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
[CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
[CLK_THS] = &ths_clk.common.hw,
@@ -727,7 +837,123 @@ static struct clk_hw_onecell_data sun8i_h3_hw_clks = {
[CLK_MBUS] = &mbus_clk.common.hw,
[CLK_GPU] = &gpu_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H3,
+};
+
+static struct clk_hw_onecell_data sun50i_h5_hw_clks = {
+ .hws = {
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO] = &pll_video_clk.common.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_AHB2] = &ahb2_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_BUS_TVE] = &bus_tve_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_SCR0] = &bus_scr0_clk.common.hw,
+ [CLK_BUS_SCR1] = &bus_scr1_clk.common.hw,
+ [CLK_BUS_EPHY] = &bus_ephy_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_TCON0] = &tcon_clk.common.hw,
+ [CLK_TVE] = &tve_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI_MISC] = &csi_misc_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI_MCLK] = &csi_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_AC_DIG] = &ac_dig_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_DDC] = &hdmi_ddc_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H5,
};
static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
@@ -790,7 +1016,71 @@ static struct ccu_reset_map sun8i_h3_ccu_resets[] = {
[RST_BUS_UART1] = { 0x2d8, BIT(17) },
[RST_BUS_UART2] = { 0x2d8, BIT(18) },
[RST_BUS_UART3] = { 0x2d8, BIT(19) },
- [RST_BUS_SCR] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+};
+
+static struct ccu_reset_map sun50i_h5_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+ [RST_USB_PHY3] = { 0x0cc, BIT(3) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(23) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(24) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI3] = { 0x2c0, BIT(27) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI3] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(3) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(4) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI] = { 0x2c4, BIT(8) },
+ [RST_BUS_TVE] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI0] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI1] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_MSGBOX] = { 0x2c4, BIT(21) },
+ [RST_BUS_SPINLOCK] = { 0x2c4, BIT(22) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_EPHY] = { 0x2c8, BIT(2) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_SCR0] = { 0x2d8, BIT(20) },
+ [RST_BUS_SCR1] = { 0x2d8, BIT(20) },
};
static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
@@ -803,6 +1093,16 @@ static const struct sunxi_ccu_desc sun8i_h3_ccu_desc = {
.num_resets = ARRAY_SIZE(sun8i_h3_ccu_resets),
};
+static const struct sunxi_ccu_desc sun50i_h5_ccu_desc = {
+ .ccu_clks = sun50i_h5_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h5_ccu_clks),
+
+ .hw_clks = &sun50i_h5_hw_clks,
+
+ .resets = sun50i_h5_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h5_ccu_resets),
+};
+
static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.common = &cpux_clk.common,
.cm = &cpux_clk.mux,
@@ -810,7 +1110,8 @@ static struct ccu_mux_nb sun8i_h3_cpu_nb = {
.bypass_index = 1, /* index of 24 MHz oscillator */
};
-static void __init sun8i_h3_ccu_setup(struct device_node *node)
+static void __init sunxi_h3_h5_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
{
void __iomem *reg;
u32 val;
@@ -827,10 +1128,22 @@ static void __init sun8i_h3_ccu_setup(struct device_node *node)
val &= ~GENMASK(19, 16);
writel(val | (3 << 16), reg + SUN8I_H3_PLL_AUDIO_REG);
- sunxi_ccu_probe(node, reg, &sun8i_h3_ccu_desc);
+ sunxi_ccu_probe(node, reg, desc);
ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
&sun8i_h3_cpu_nb);
}
+
+static void __init sun8i_h3_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun8i_h3_ccu_desc);
+}
CLK_OF_DECLARE(sun8i_h3_ccu, "allwinner,sun8i-h3-ccu",
sun8i_h3_ccu_setup);
+
+static void __init sun50i_h5_ccu_setup(struct device_node *node)
+{
+ sunxi_h3_h5_ccu_init(node, &sun50i_h5_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h5_ccu, "allwinner,sun50i-h5-ccu",
+ sun50i_h5_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
index 78be712c7487..85973d1e8165 100644
--- a/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-h3.h
@@ -57,6 +57,7 @@
/* And the GPU module clock is exported */
-#define CLK_NUMBER (CLK_GPU + 1)
+#define CLK_NUMBER_H3 (CLK_GPU + 1)
+#define CLK_NUMBER_H5 (CLK_BUS_SCR1 + 1)
#endif /* _CCU_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index efb7ba2bd515..c2afc41d6964 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -91,7 +91,7 @@
#define CLK_BUS_UART1 63
#define CLK_BUS_UART2 64
#define CLK_BUS_UART3 65
-#define CLK_BUS_SCR 66
+#define CLK_BUS_SCR0 66
#define CLK_BUS_EPHY 67
#define CLK_BUS_DBG 68
@@ -142,4 +142,7 @@
#define CLK_GPU 114
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1 115
+
#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
index 6b7af80c26ec..484c2a22919d 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -98,6 +98,9 @@
#define RST_BUS_UART1 50
#define RST_BUS_UART2 51
#define RST_BUS_UART3 52
-#define RST_BUS_SCR 53
+#define RST_BUS_SCR0 53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1 54
#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
2017-03-01 20:13 ` Icenowy Zheng
(?)
@ 2017-03-01 20:13 ` Icenowy Zheng
-1 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
controller (see the "Note" after the interrupt source table), so the GIC
node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
changed to "arm,gic-400".
On the way get rid of skeleton.dtsi, as recommended in that very file.
The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
at all after changing pinctrl binding to the generic pinconf binding.
[1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
[2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, drop pinctrl-a10.h which is now unused with generic
pinconf binding]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v6:
- Extract GIC device node to sunxi-h3-h5.dtsi and correct its compatible
as "arm,gic-400".
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 774 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 78 +--
2 files changed, 134 insertions(+), 718 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (83%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (90%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 83%
index 27780b97c863..b36f9f423c39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,126 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif@0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif@01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 90%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 27780b97c863..2494ea063cd4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -589,7 +527,7 @@
};
gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
controller (see the "Note" after the interrupt source table), so the GIC
node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
changed to "arm,gic-400".
On the way get rid of skeleton.dtsi, as recommended in that very file.
The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
at all after changing pinctrl binding to the generic pinconf binding.
[1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
[2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, drop pinctrl-a10.h which is now unused with generic
pinconf binding]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Extract GIC device node to sunxi-h3-h5.dtsi and correct its compatible
as "arm,gic-400".
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 774 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 78 +--
2 files changed, 134 insertions(+), 718 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (83%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (90%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 83%
index 27780b97c863..b36f9f423c39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,126 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif@0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif@01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 90%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 27780b97c863..2494ea063cd4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -589,7 +527,7 @@
};
gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
controller (see the "Note" after the interrupt source table), so the GIC
node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
changed to "arm,gic-400".
On the way get rid of skeleton.dtsi, as recommended in that very file.
The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
at all after changing pinctrl binding to the generic pinconf binding.
[1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
[2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, drop pinctrl-a10.h which is now unused with generic
pinconf binding]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Extract GIC device node to sunxi-h3-h5.dtsi and correct its compatible
as "arm,gic-400".
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 774 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 78 +--
2 files changed, 134 insertions(+), 718 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (83%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (90%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 83%
index 27780b97c863..b36f9f423c39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,648 +1,126 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk at 01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk at 01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller at 01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy at 01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb at 01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb at 01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at 01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb at 01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb at 01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0 at 0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin at 0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1 at 0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif at 0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0 at 0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer at 01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi at 01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi at 01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog at 01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif at 01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm at 01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec at 01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial at 01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial at 01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial at 01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial at 01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c at 01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller at 01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc at 01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset at 01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog at 01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir at 01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir at 0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 90%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 27780b97c863..2494ea063cd4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,52 +40,14 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -150,16 +112,8 @@
};
mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -169,16 +123,8 @@
};
mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -188,16 +134,8 @@
};
mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -308,7 +246,7 @@
};
ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -317,7 +255,7 @@
};
pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -589,7 +527,7 @@
};
gic: interrupt-controller at 01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 3/4] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-03-01 20:13 ` Icenowy Zheng
(?)
@ 2017-03-01 20:13 ` Icenowy Zheng
-1 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v6:
- Dropped GIC node as it's in sunxi-h3-h5.dtsi now
- Fixed some words in commit message, thanks to Rask Ingemann Lambertsen
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..4d314a253fd9
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 3/4] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Dropped GIC node as it's in sunxi-h3-h5.dtsi now
- Fixed some words in commit message, thanks to Rask Ingemann Lambertsen
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..4d314a253fd9
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 3/4] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Dropped GIC node as it's in sunxi-h3-h5.dtsi now
- Fixed some words in commit message, thanks to Rask Ingemann Lambertsen
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..4d314a253fd9
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 4/4] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-03-01 20:13 ` Icenowy Zheng
(?)
@ 2017-03-01 20:13 ` Icenowy Zheng
-1 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v6:
- Renamed some node names to prevent underscores and changed MMC card
detect GPIO to active-low. Thanks to Rask Ingemann Lambertsen.
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 +++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..30639729920d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 4/4] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Andre Przywara
Cc: devicetree, linux-kernel, linux-sunxi, Icenowy Zheng, linux-clk,
linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Renamed some node names to prevent underscores and changed MMC card
detect GPIO to active-low. Thanks to Rask Ingemann Lambertsen.
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 +++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..30639729920d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [PATCH v6 4/4] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-01 20:13 ` Icenowy Zheng
0 siblings, 0 replies; 23+ messages in thread
From: Icenowy Zheng @ 2017-03-01 20:13 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Renamed some node names to prevent underscores and changed MMC card
detect GPIO to active-low. Thanks to Rask Ingemann Lambertsen.
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 +++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..30639729920d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-02 13:55 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Rob Herring, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 571 bytes --]
On Thu, Mar 02, 2017 at 04:13:39AM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a design which keeps the peripheral
> compatible with H3, so that it have also a CCU like the one on H3 --
> only one bus gate/reset is added, and the mmc sample/output phases are
> removed because of MMC controller update.
>
> Add its support in our existing H3 CCU driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-02 13:55 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Rob Herring, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 573 bytes --]
On Thu, Mar 02, 2017 at 04:13:39AM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a design which keeps the peripheral
> compatible with H3, so that it have also a CCU like the one on H3 --
> only one bus gate/reset is added, and the mmc sample/output phases are
> removed because of MMC controller update.
>
> Add its support in our existing H3 CCU driver.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-02 13:55 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:55 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Andre Przywara, linux-sunxi, linux-kernel,
Chen-Yu Tsai, Rob Herring, linux-clk, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 571 bytes --]
On Thu, Mar 02, 2017 at 04:13:39AM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a design which keeps the peripheral
> compatible with H3, so that it have also a CCU like the one on H3 --
> only one bus gate/reset is added, and the mmc sample/output phases are
> removed because of MMC controller update.
>
> Add its support in our existing H3 CCU driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver
@ 2017-03-02 13:55 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:55 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Mar 02, 2017 at 04:13:39AM +0800, Icenowy Zheng wrote:
> Allwinner H5 is a SoC that features a design which keeps the peripheral
> compatible with H3, so that it have also a CCU like the one on H3 --
> only one bus gate/reset is added, and the mmc sample/output phases are
> removed because of MMC controller update.
>
> Add its support in our existing H3 CCU driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170302/96cc8a9e/attachment.sig>
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-02 13:58 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Rob Herring, Andre Przywara, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 1574 bytes --]
On Thu, Mar 02, 2017 at 04:13:40AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
> Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
> 2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
> controller (see the "Note" after the interrupt source table), so the GIC
> node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
> changed to "arm,gic-400".
This should be in a separate patch.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
That too.
> The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
> at all after changing pinctrl binding to the generic pinconf binding.
And that as well...
> [1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
> [2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Please don't put URLs in commit logs.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-02 13:58 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Rob Herring, Andre Przywara,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 1554 bytes --]
On Thu, Mar 02, 2017 at 04:13:40AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
> Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
> 2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
> controller (see the "Note" after the interrupt source table), so the GIC
> node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
> changed to "arm,gic-400".
This should be in a separate patch.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
That too.
> The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
> at all after changing pinctrl binding to the generic pinconf binding.
And that as well...
> [1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
> [2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Please don't put URLs in commit logs.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-02 13:58 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: devicetree, Andre Przywara, linux-sunxi, linux-kernel,
Chen-Yu Tsai, Rob Herring, linux-clk, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1574 bytes --]
On Thu, Mar 02, 2017 at 04:13:40AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
> Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
> 2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
> controller (see the "Note" after the interrupt source table), so the GIC
> node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
> changed to "arm,gic-400".
This should be in a separate patch.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
That too.
> The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
> at all after changing pinctrl binding to the generic pinconf binding.
And that as well...
> [1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
> [2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Please don't put URLs in commit logs.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-02 13:58 ` Maxime Ripard
0 siblings, 0 replies; 23+ messages in thread
From: Maxime Ripard @ 2017-03-02 13:58 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Mar 02, 2017 at 04:13:40AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
> Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
> updated. So we should really share almost the whole .dtsi.
> In preparation for that move the peripheral parts of the existing
> sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
> The actual sun8i-h3.dtsi then includes that and defines the H3 specific
> parts on top of it.
> According to "Allwinner H3 Datasheet Version 1.2 Apr. 23, 2015" [1]
> Chapter 4.12. GIC and "Allwinner H5 Datasheet Revision 1.0 May. 20,
> 2016" [2] Chapter 4.12. GIC, the two SoCs both use ARM GIC-400 interrupt
> controller (see the "Note" after the interrupt source table), so the GIC
> node is extracted to sunxi-h3-h5.dtsi as well, and the compatible is
> changed to "arm,gic-400".
This should be in a separate patch.
> On the way get rid of skeleton.dtsi, as recommended in that very file.
That too.
> The inclusion of pinctrl-a10.h is also dropped, as it's now not needed
> at all after changing pinctrl binding to the generic pinconf binding.
And that as well...
> [1] http://linux-sunxi.org/File:Allwinner_H3_Datasheet_V1.2.pdf
> [2] https://github.com/OrangePiLibra/OrangePi_H5SDK/blob/master/Documentation/Hardware/H5_User_Manual.pdf
Please don't put URLs in commit logs.
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170302/027496b3/attachment.sig>
^ permalink raw reply [flat|nested] 23+ messages in thread
end of thread, other threads:[~2017-03-02 14:02 UTC | newest]
Thread overview: 23+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-01 20:13 [PATCH v6 0/4] Allwinner H5 and Orange Pi PC2 support Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
[not found] ` <20170301201342.47583-1-icenowy-ymACFijhrKM@public.gmane.org>
2017-03-01 20:13 ` [PATCH v6 1/4] clk: sunxi-ng: add Allwinner H5 CCU support for H3 CCU driver Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-02 13:55 ` Maxime Ripard
2017-03-02 13:55 ` Maxime Ripard
2017-03-02 13:55 ` Maxime Ripard
2017-03-02 13:55 ` Maxime Ripard
2017-03-01 20:13 ` [PATCH] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-02 13:58 ` Maxime Ripard
2017-03-02 13:58 ` Maxime Ripard
2017-03-02 13:58 ` Maxime Ripard
2017-03-02 13:58 ` Maxime Ripard
2017-03-01 20:13 ` [PATCH v6 3/4] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` [PATCH v6 4/4] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
2017-03-01 20:13 ` Icenowy Zheng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.