* [PATCH v7 0/6] Allwinner H5 and Orange Pi PC2 support
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3, and it's pin-to-pin compatible with H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Several H5 boards by Sinovoip Banana Pi and FriendlyARM Nano Pi
are coming, so we should get ready for them.
CCU changes are already said to be merged by Maxime Ripard, so
this patchset now contains only device tree patches.
Some cleanups applied to H3 DTSI is extracted to separated commits,
according to the suggestion of Maxime.
This patchset depends on patchset [1] to finally take effect. At
least the patch 1 of that patchset is needed if you want to test
the kernel image -- without it the pinctrl driver won't be built
and the kernel will become unusable without pinctrl.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490780.html
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (3):
ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
ARM: dts: sun8i: drop pinctrl-a10.h inclusion for H3 DTSI
ARM: dts: sun8i: correct the GIC compatible in H3 to gic-400
arch/arm/boot/dts/sun8i-h3.dtsi | 602 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 586 ++++++++++++++++++++
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
6 files changed, 915 insertions(+), 562 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
--
2.11.1
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 0/6] Allwinner H5 and Orange Pi PC2 support
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
Allwinner H5 is a 64-bit SoC with a design like the 32-bit
H3, and it's pin-to-pin compatible with H3.
This patchset adds support for it, along with the first available
board -- Orange Pi PC2.
Several H5 boards by Sinovoip Banana Pi and FriendlyARM Nano Pi
are coming, so we should get ready for them.
CCU changes are already said to be merged by Maxime Ripard, so
this patchset now contains only device tree patches.
Some cleanups applied to H3 DTSI is extracted to separated commits,
according to the suggestion of Maxime.
This patchset depends on patchset [1] to finally take effect. At
least the patch 1 of that patchset is needed if you want to test
the kernel image -- without it the pinctrl driver won't be built
and the kernel will become unusable without pinctrl.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490780.html
Andre Przywara (3):
arm: dts: sun8i: split Allwinner H3 .dtsi
arm64: dts: allwinner: add Allwinner H5 .dtsi
arm64: dts: sunxi: add support for the Orange Pi PC 2 board
Icenowy Zheng (3):
ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
ARM: dts: sun8i: drop pinctrl-a10.h inclusion for H3 DTSI
ARM: dts: sun8i: correct the GIC compatible in H3 to gic-400
arch/arm/boot/dts/sun8i-h3.dtsi | 602 ++-------------------
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 586 ++++++++++++++++++++
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 ++++++
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
6 files changed, 915 insertions(+), 562 deletions(-)
create mode 100644 arch/arm/boot/dts/sunxi-h3-h5.dtsi
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
--
2.11.1
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 27780b97c863..9a3435527fde 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,8 +40,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 27780b97c863..9a3435527fde 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,8 +40,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 2/6] ARM: dts: sun8i: drop pinctrl-a10.h inclusion for H3 DTSI
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 9a3435527fde..b250e6d03b57 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,7 +42,6 @@
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 2/6] ARM: dts: sun8i: drop pinctrl-a10.h inclusion for H3 DTSI
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 9a3435527fde..b250e6d03b57 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -42,7 +42,6 @@
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 3/6] ARM: dts: sun8i: correct the GIC compatible in H3 to gic-400
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index b250e6d03b57..c13fbfb92592 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -586,7 +586,7 @@
};
gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 3/6] ARM: dts: sun8i: correct the GIC compatible in H3 to gic-400
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
New patch extracted in v7.
arch/arm/boot/dts/sun8i-h3.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index b250e6d03b57..c13fbfb92592 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -586,7 +586,7 @@
};
gic: interrupt-controller at 01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Andre Przywara,
Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a separated patch]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v7:
- Extract GIC, skeleton.dtsi and pinctrl-a10.h changes to seperate patches.
Changes in v6:
- Extract GIC device node to sunxi-h3-h5.dtsi and correct its compatible
as "arm,gic-400".
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 771 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 73 +-
2 files changed, 133 insertions(+), 711 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (83%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (90%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 83%
index c13fbfb92592..b36f9f423c39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,645 +1,126 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0@0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1@0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif@0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0@0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi@01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi@01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif@01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm@01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec@01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c@01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c@01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller@01c81000 {
- compatible = "arm,gic-400";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog@01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir@0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 90%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index c13fbfb92592..2494ea063cd4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -46,43 +46,8 @@
/ {
interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu@2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu@3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -147,16 +112,8 @@
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -166,16 +123,8 @@
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -185,16 +134,8 @@
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -305,7 +246,7 @@
};
ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -314,7 +255,7 @@
};
pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a separated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v7:
- Extract GIC, skeleton.dtsi and pinctrl-a10.h changes to seperate patches.
Changes in v6:
- Extract GIC device node to sunxi-h3-h5.dtsi and correct its compatible
as "arm,gic-400".
Changes in v3:
- Use label-based syntax to reference nodes in H3 DTSI file.
Changes in v2:
- Rebase on current linux-next (because of the add of audio codec)
arch/arm/boot/dts/sun8i-h3.dtsi | 771 ++++-----------------
.../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 73 +-
2 files changed, 133 insertions(+), 711 deletions(-)
rewrite arch/arm/boot/dts/sun8i-h3.dtsi (83%)
copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (90%)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
dissimilarity index 83%
index c13fbfb92592..b36f9f423c39 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -1,645 +1,126 @@
-/*
- * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
-
-/ {
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk at 01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk at 01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller at 01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy at 01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb at 01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb at 01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at 01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb at 01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb at 01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0 at 0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin at 0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1 at 0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spdif_tx_pins_a: spdif at 0 {
- pins = "PA17";
- function = "spdif";
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0 at 0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
- };
-
- timer at 01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- spi0: spi at 01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi at 01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog at 01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- spdif: spdif at 01c21000 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-spdif";
- reg = <0x01c21000 0x400>;
- interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
- resets = <&ccu RST_BUS_SPDIF>;
- clock-names = "apb", "spdif";
- dmas = <&dma 2>;
- dma-names = "tx";
- status = "disabled";
- };
-
- pwm: pwm at 01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- codec: codec at 01c22c00 {
- #sound-dai-cells = <0>;
- compatible = "allwinner,sun8i-h3-codec";
- reg = <0x01c22c00 0x400>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
- clock-names = "apb", "codec";
- resets = <&ccu RST_BUS_CODEC>;
- dmas = <&dma 15>, <&dma 15>;
- dma-names = "rx", "tx";
- allwinner,codec-analog-controls = <&codec_analog>;
- status = "disabled";
- };
-
- uart0: serial at 01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial at 01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial at 01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial at 01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c at 01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gic: interrupt-controller at 01c81000 {
- compatible = "arm,gic-400";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x2000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- rtc: rtc at 01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset at 01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- codec_analog: codec-analog at 01f015c0 {
- compatible = "allwinner,sun8i-h3-codec-analog";
- reg = <0x01f015c0 0x4>;
- };
-
- ir: ir at 01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir at 0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
- };
-};
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
+
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
similarity index 90%
copy from arch/arm/boot/dts/sun8i-h3.dtsi
copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi
index c13fbfb92592..2494ea063cd4 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -46,43 +46,8 @@
/ {
interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- };
-
- cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <1>;
- };
-
- cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <2>;
- };
-
- cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <3>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- };
+ #address-cells = <1>;
+ #size-cells = <1>;
clocks {
#address-cells = <1>;
@@ -147,16 +112,8 @@
};
mmc0: mmc at 01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
@@ -166,16 +123,8 @@
};
mmc1: mmc at 01c10000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
@@ -185,16 +134,8 @@
};
mmc2: mmc at 01c11000 {
- compatible = "allwinner,sun7i-a20-mmc";
+ /* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
@@ -305,7 +246,7 @@
};
ccu: clock at 01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
@@ -314,7 +255,7 @@
};
pio: pinctrl at 01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
+ /* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Andre Przywara,
Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v6:
- Dropped GIC node as it's in sunxi-h3-h5.dtsi now
- Fixed some words in commit message, thanks to Rask Ingemann Lambertsen
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
incompatible
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..4d314a253fd9
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Dropped GIC node as it's in sunxi-h3-h5.dtsi now
- Fixed some words in commit message, thanks to Rask Ingemann Lambertsen
Changes in v3:
- Dropped sun5i-a13-mmc, sun8i-h3-ccu compatibles.
- Used sun50i-{h5,a64}-emmc compatible for mmc2.
Changes in v2:
- Dropped sun8i-h3-pinctrl compatible, as the interrupt of H3 and H5 is
incompatible
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 124 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi | 1 +
2 files changed, 125 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..4d314a253fd9
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,124 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-h3-h5.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&ccu {
+ compatible = "allwinner,sun50i-h5-ccu";
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc1 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+};
+
+&mmc2 {
+ compatible = "allwinner,sun50i-h5-emmc",
+ "allwinner,sun50i-a64-emmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+};
+
+&pio {
+ compatible = "allwinner,sun50i-h5-pinctrl";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
new file mode 120000
index 000000000000..036f01dc2b9b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sunxi-h3-h5.dtsi
\ No newline at end of file
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-03-05 23:31 ` Icenowy Zheng
@ 2017-03-05 23:31 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Andre Przywara,
Icenowy Zheng
From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
---
Changes in v6:
- Renamed some node names to prevent underscores and changed MMC card
detect GPIO to active-low. Thanks to Rask Ingemann Lambertsen.
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 +++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..30639729920d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-05 23:31 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-05 23:31 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
Changes in v6:
- Renamed some node names to prevent underscores and changed MMC card
detect GPIO to active-low. Thanks to Rask Ingemann Lambertsen.
Changes in v2:
- Dropped all GPIO pinctrl nodes.
- Changed red LED gpio to the correct one.
- Added audio codec configuration copied from Orange Pi PC.
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 163 +++++++++++++++++++++
2 files changed, 164 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index bc6f342be59f..244e8b7565f9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..30639729920d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.1
^ permalink raw reply related [flat|nested] 27+ messages in thread
* Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:35 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:35 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 523 bytes --]
Hi,
On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
> environment.
>
> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
> chip, drop skeleton.dtsi inclusion now.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Your prefix (and in the three later patches) should be
ARM: sun8i: h3
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:35 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:35 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 522 bytes --]
Hi,
On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
> environment.
>
> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
> chip, drop skeleton.dtsi inclusion now.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Your prefix (and in the three later patches) should be
ARM: sun8i: h3
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:35 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:35 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
> environment.
>
> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
> chip, drop skeleton.dtsi inclusion now.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Your prefix (and in the three later patches) should be
ARM: sun8i: h3
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170306/b996f653/attachment-0001.sig>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-06 10:37 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:37 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi, Andre Przywara
[-- Attachment #1: Type: text/plain, Size: 1080 bytes --]
On Mon, Mar 06, 2017 at 07:31:38AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Orange Pi PC 2 is a typical single board computer using the
> Allwinner H5 SoC. Apart from the usual suspects it features three
> separately driven USB ports and a Gigabit Ethernet port.
> Also it has a SPI NOR flash soldered, from which the board can boot
> from. This enables the SBC to behave like a "real computer" with
> built-in firmware.
>
> Add the board specific .dts file, which includes the H5 .dtsi and
> enables the peripherals that we support so far.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
> change MMC cd to active-low, rename some node names to prevent
> underscores]
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
And here your prefix should be "arm64: allwinner: h5:"
(This also applies to your previous patch).
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-06 10:37 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:37 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Andre Przywara
[-- Attachment #1: Type: text/plain, Size: 1112 bytes --]
On Mon, Mar 06, 2017 at 07:31:38AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>
> The Orange Pi PC 2 is a typical single board computer using the
> Allwinner H5 SoC. Apart from the usual suspects it features three
> separately driven USB ports and a Gigabit Ethernet port.
> Also it has a SPI NOR flash soldered, from which the board can boot
> from. This enables the SBC to behave like a "real computer" with
> built-in firmware.
>
> Add the board specific .dts file, which includes the H5 .dtsi and
> enables the peripherals that we support so far.
>
> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
> [Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
> change MMC cd to active-low, rename some node names to prevent
> underscores]
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
And here your prefix should be "arm64: allwinner: h5:"
(This also applies to your previous patch).
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-06 10:37 ` Maxime Ripard
0 siblings, 0 replies; 27+ messages in thread
From: Maxime Ripard @ 2017-03-06 10:37 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Mar 06, 2017 at 07:31:38AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Orange Pi PC 2 is a typical single board computer using the
> Allwinner H5 SoC. Apart from the usual suspects it features three
> separately driven USB ports and a Gigabit Ethernet port.
> Also it has a SPI NOR flash soldered, from which the board can boot
> from. This enables the SBC to behave like a "real computer" with
> built-in firmware.
>
> Add the board specific .dts file, which includes the H5 .dtsi and
> enables the peripherals that we support so far.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> [Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
> change MMC cd to active-low, rename some node names to prevent
> underscores]
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
And here your prefix should be "arm64: allwinner: h5:"
(This also applies to your previous patch).
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170306/8607d32a/attachment.sig>
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
2017-03-06 10:35 ` Maxime Ripard
@ 2017-03-06 10:46 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-06 10:46 UTC (permalink / raw)
To: Maxime Ripard
Cc: Rob Herring, Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
06.03.2017, 18:35, "Maxime Ripard" <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>:
> Hi,
>
> On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
>> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
>> environment.
>>
>> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
>> chip, drop skeleton.dtsi inclusion now.
>>
>> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>
> Your prefix (and in the three later patches) should be
> ARM: sun8i: h3
Oh I think we never added SoC name in prefix...
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:46 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-06 10:46 UTC (permalink / raw)
To: linux-arm-kernel
06.03.2017, 18:35, "Maxime Ripard" <maxime.ripard@free-electrons.com>:
> Hi,
>
> On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
>> ?The skeleton.dtsi file is now deprecated, and do not exist in ARM64
>> ?environment.
>>
>> ?Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
>> ?chip, drop skeleton.dtsi inclusion now.
>>
>> ?Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>
> Your prefix (and in the three later patches) should be
> ARM: sun8i: h3
Oh I think we never added SoC name in prefix...
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2017-03-06 10:37 ` Maxime Ripard
@ 2017-03-06 10:47 ` Icenowy Zheng
-1 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-06 10:47 UTC (permalink / raw)
To: Maxime Ripard
Cc: Rob Herring, Chen-Yu Tsai, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Andre Przywara
06.03.2017, 18:37, "Maxime Ripard" <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>:
> On Mon, Mar 06, 2017 at 07:31:38AM +0800, Icenowy Zheng wrote:
>> From: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>>
>> The Orange Pi PC 2 is a typical single board computer using the
>> Allwinner H5 SoC. Apart from the usual suspects it features three
>> separately driven USB ports and a Gigabit Ethernet port.
>> Also it has a SPI NOR flash soldered, from which the board can boot
>> from. This enables the SBC to behave like a "real computer" with
>> built-in firmware.
>>
>> Add the board specific .dts file, which includes the H5 .dtsi and
>> enables the peripherals that we support so far.
>>
>> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
>> [Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
>> change MMC cd to active-low, rename some node names to prevent
>> underscores]
>> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>
> And here your prefix should be "arm64: allwinner: h5:"
Is this a new standard to have SoC name in prefix?
>
> (This also applies to your previous patch).
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 27+ messages in thread
* [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
@ 2017-03-06 10:47 ` Icenowy Zheng
0 siblings, 0 replies; 27+ messages in thread
From: Icenowy Zheng @ 2017-03-06 10:47 UTC (permalink / raw)
To: linux-arm-kernel
06.03.2017, 18:37, "Maxime Ripard" <maxime.ripard@free-electrons.com>:
> On Mon, Mar 06, 2017 at 07:31:38AM +0800, Icenowy Zheng wrote:
>> ?From: Andre Przywara <andre.przywara@arm.com>
>>
>> ?The Orange Pi PC 2 is a typical single board computer using the
>> ?Allwinner H5 SoC. Apart from the usual suspects it features three
>> ?separately driven USB ports and a Gigabit Ethernet port.
>> ?Also it has a SPI NOR flash soldered, from which the board can boot
>> ?from. This enables the SBC to behave like a "real computer" with
>> ?built-in firmware.
>>
>> ?Add the board specific .dts file, which includes the H5 .dtsi and
>> ?enables the peripherals that we support so far.
>>
>> ?Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> ?[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
>> ??change MMC cd to active-low, rename some node names to prevent
>> ??underscores]
>> ?Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>
> And here your prefix should be "arm64: allwinner: h5:"
Is this a new standard to have SoC name in prefix?
>
> (This also applies to your previous patch).
>
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [linux-sunxi] Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:48 ` Chen-Yu Tsai
0 siblings, 0 replies; 27+ messages in thread
From: Chen-Yu Tsai @ 2017-03-06 10:48 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Rob Herring, Chen-Yu Tsai, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi
On Mon, Mar 6, 2017 at 6:46 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
>
>
> 06.03.2017, 18:35, "Maxime Ripard" <maxime.ripard@free-electrons.com>:
>> Hi,
>>
>> On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
>>> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
>>> environment.
>>>
>>> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
>>> chip, drop skeleton.dtsi inclusion now.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>>
>> Your prefix (and in the three later patches) should be
>> ARM: sun8i: h3
>
> Oh I think we never added SoC name in prefix...
It's better to add them for sun8i, which encompasses a whole
bunch of SoCs, unlike the older sun[4-7]i. Even sun5i patches
have them.
ChenYu
^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:48 ` Chen-Yu Tsai
0 siblings, 0 replies; 27+ messages in thread
From: Chen-Yu Tsai @ 2017-03-06 10:48 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Rob Herring, Chen-Yu Tsai,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
On Mon, Mar 6, 2017 at 6:46 PM, Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org> wrote:
>
>
> 06.03.2017, 18:35, "Maxime Ripard" <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>:
>> Hi,
>>
>> On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
>>> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
>>> environment.
>>>
>>> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
>>> chip, drop skeleton.dtsi inclusion now.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>>
>> Your prefix (and in the three later patches) should be
>> ARM: sun8i: h3
>
> Oh I think we never added SoC name in prefix...
It's better to add them for sun8i, which encompasses a whole
bunch of SoCs, unlike the older sun[4-7]i. Even sun5i patches
have them.
ChenYu
^ permalink raw reply [flat|nested] 27+ messages in thread
* [linux-sunxi] Re: [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI
@ 2017-03-06 10:48 ` Chen-Yu Tsai
0 siblings, 0 replies; 27+ messages in thread
From: Chen-Yu Tsai @ 2017-03-06 10:48 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Mar 6, 2017 at 6:46 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
>
>
> 06.03.2017, 18:35, "Maxime Ripard" <maxime.ripard@free-electrons.com>:
>> Hi,
>>
>> On Mon, Mar 06, 2017 at 07:31:33AM +0800, Icenowy Zheng wrote:
>>> The skeleton.dtsi file is now deprecated, and do not exist in ARM64
>>> environment.
>>>
>>> Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
>>> chip, drop skeleton.dtsi inclusion now.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
>>
>> Your prefix (and in the three later patches) should be
>> ARM: sun8i: h3
>
> Oh I think we never added SoC name in prefix...
It's better to add them for sun8i, which encompasses a whole
bunch of SoCs, unlike the older sun[4-7]i. Even sun5i patches
have them.
ChenYu
^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2017-03-06 10:59 UTC | newest]
Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-05 23:31 [PATCH v7 0/6] Allwinner H5 and Orange Pi PC2 support Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
[not found] ` <20170305233138.64574-1-icenowy-ymACFijhrKM@public.gmane.org>
2017-03-05 23:31 ` [PATCH v7 1/6] ARM: dts: sun8i: drop skeleton.dtsi inclusion in H3 DTSI Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-06 10:35 ` Maxime Ripard
2017-03-06 10:35 ` Maxime Ripard
2017-03-06 10:35 ` Maxime Ripard
2017-03-06 10:46 ` Icenowy Zheng
2017-03-06 10:46 ` Icenowy Zheng
2017-03-06 10:48 ` [linux-sunxi] " Chen-Yu Tsai
2017-03-06 10:48 ` Chen-Yu Tsai
2017-03-06 10:48 ` Chen-Yu Tsai
2017-03-05 23:31 ` [PATCH v7 2/6] ARM: dts: sun8i: drop pinctrl-a10.h inclusion for " Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-05 23:31 ` [PATCH v7 3/6] ARM: dts: sun8i: correct the GIC compatible in H3 to gic-400 Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-05 23:31 ` [PATCH v7 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-05 23:31 ` [PATCH v7 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-05 23:31 ` [PATCH v7 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
2017-03-05 23:31 ` Icenowy Zheng
2017-03-06 10:37 ` Maxime Ripard
2017-03-06 10:37 ` Maxime Ripard
2017-03-06 10:37 ` Maxime Ripard
2017-03-06 10:47 ` Icenowy Zheng
2017-03-06 10:47 ` Icenowy Zheng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.