[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Doug Berger]

This patch set contains changes to enable the GISB arbiter driver
on the latest ARM64 architecture Set-Top Box chips from Broadcom.

Since the ARM64 architecture does not support the hooking of low
level fault handlers the driver has been adjusted to depend solely
on GISB interrupts and notify events to provide diagnostic
messaging.  The GISB hardware still triggers bus faults for the
processor so the default low-level aborts will occur and will be
handled based on the architecture specific kernel implementation.

While this tends to obsure the GISB error messaging it is still
reasonable so the same approach is applied to the ARM architecture
for consistency.

The patches also correct some issues with the existing driver
and add the new register map for the GISBv7 hardware first
appearing in the BCM7278 device.

Changes since v2 at [2]:
 - Removed code associated with enabling the hooking of ARM64
   memory faults as well as the code that hooks them for both
   ARM and ARM64 architectures within the GISB arbiter driver.
 - Created separate notifiers for die and panic events to
   prevent list corruption, and substituted the notifier return
   name for the previous magic number (Thanks Mark!)

Changes since v1 at [1]:
 - Removed code associated with hooking SError handling in favor
   of a registered notifier (Thanks Mark!)
 - Removed an unnecessary explicit cast (Thanks Gregory!)

[1] https://lkml.org/lkml/2017/3/24/413
[2] https://lkml.org/lkml/2017/3/28/1125

Doug Berger (6):
  bus: brcmstb_gisb: Use register offsets with writes too
  bus: brcmstb_gisb: correct support for 64-bit address output
  bus: brcmstb_gisb: add notifier handling
  bus: brcmstb_gisb: remove low-level ARM hooks
  bus: brcmstb_gisb: enable driver for ARM64 architecture
  bus: brcmstb_gisb: update to support new revision

 .../devicetree/bindings/bus/brcm,gisb-arb.txt      |   3 +-
 drivers/bus/Kconfig                                |   2 +-
 drivers/bus/brcmstb_gisb.c                         | 121 ++++++++++++---------
 3 files changed, 75 insertions(+), 51 deletions(-)

-- 
2.12.0

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Doug Berger]

This patch set contains changes to enable the GISB arbiter driver
on the latest ARM64 architecture Set-Top Box chips from Broadcom.

Since the ARM64 architecture does not support the hooking of low
level fault handlers the driver has been adjusted to depend solely
on GISB interrupts and notify events to provide diagnostic
messaging.  The GISB hardware still triggers bus faults for the
processor so the default low-level aborts will occur and will be
handled based on the architecture specific kernel implementation.

While this tends to obsure the GISB error messaging it is still
reasonable so the same approach is applied to the ARM architecture
for consistency.

The patches also correct some issues with the existing driver
and add the new register map for the GISBv7 hardware first
appearing in the BCM7278 device.

Changes since v2 at [2]:
 - Removed code associated with enabling the hooking of ARM64
   memory faults as well as the code that hooks them for both
   ARM and ARM64 architectures within the GISB arbiter driver.
 - Created separate notifiers for die and panic events to
   prevent list corruption, and substituted the notifier return
   name for the previous magic number (Thanks Mark!)

Changes since v1 at [1]:
 - Removed code associated with hooking SError handling in favor
   of a registered notifier (Thanks Mark!)
 - Removed an unnecessary explicit cast (Thanks Gregory!)

[1] https://lkml.org/lkml/2017/3/24/413
[2] https://lkml.org/lkml/2017/3/28/1125

Doug Berger (6):
  bus: brcmstb_gisb: Use register offsets with writes too
  bus: brcmstb_gisb: correct support for 64-bit address output
  bus: brcmstb_gisb: add notifier handling
  bus: brcmstb_gisb: remove low-level ARM hooks
  bus: brcmstb_gisb: enable driver for ARM64 architecture
  bus: brcmstb_gisb: update to support new revision

 .../devicetree/bindings/bus/brcm,gisb-arb.txt      |   3 +-
 drivers/bus/Kconfig                                |   2 +-
 drivers/bus/brcmstb_gisb.c                         | 121 ++++++++++++---------
 3 files changed, 75 insertions(+), 51 deletions(-)

-- 
2.12.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Doug Berger]

This patch set contains changes to enable the GISB arbiter driver
on the latest ARM64 architecture Set-Top Box chips from Broadcom.

Since the ARM64 architecture does not support the hooking of low
level fault handlers the driver has been adjusted to depend solely
on GISB interrupts and notify events to provide diagnostic
messaging.  The GISB hardware still triggers bus faults for the
processor so the default low-level aborts will occur and will be
handled based on the architecture specific kernel implementation.

While this tends to obsure the GISB error messaging it is still
reasonable so the same approach is applied to the ARM architecture
for consistency.

The patches also correct some issues with the existing driver
and add the new register map for the GISBv7 hardware first
appearing in the BCM7278 device.

Changes since v2 at [2]:
 - Removed code associated with enabling the hooking of ARM64
   memory faults as well as the code that hooks them for both
   ARM and ARM64 architectures within the GISB arbiter driver.
 - Created separate notifiers for die and panic events to
   prevent list corruption, and substituted the notifier return
   name for the previous magic number (Thanks Mark!)

Changes since v1 at [1]:
 - Removed code associated with hooking SError handling in favor
   of a registered notifier (Thanks Mark!)
 - Removed an unnecessary explicit cast (Thanks Gregory!)

[1] https://lkml.org/lkml/2017/3/24/413
[2] https://lkml.org/lkml/2017/3/28/1125

Doug Berger (6):
  bus: brcmstb_gisb: Use register offsets with writes too
  bus: brcmstb_gisb: correct support for 64-bit address output
  bus: brcmstb_gisb: add notifier handling
  bus: brcmstb_gisb: remove low-level ARM hooks
  bus: brcmstb_gisb: enable driver for ARM64 architecture
  bus: brcmstb_gisb: update to support new revision

 .../devicetree/bindings/bus/brcm,gisb-arb.txt      |   3 +-
 drivers/bus/Kconfig                                |   2 +-
 drivers/bus/brcmstb_gisb.c                         | 121 ++++++++++++---------
 3 files changed, 75 insertions(+), 51 deletions(-)

-- 
2.12.0

[PATCH v3 1/6] bus: brcmstb_gisb: Use register offsets with writes too

[Doug Berger]

This commit corrects the bug introduced in commit f80835875d3d
("bus: brcmstb_gisb: Look up register offsets in a table") such
that gisb_write() translates the register enumeration into an
offset from the base address for writes as well as reads.

Fixes: f80835875d3d ("bus: brcmstb_gisb: Look up register offsets in a table")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 72fe0a5a8bf3..a94598d0945a 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Broadcom Corporation
+ * Copyright (C) 2014-2017 Broadcom
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -127,9 +127,9 @@ static void gisb_write(struct brcmstb_gisb_arb_device *gdev, u32 val, int reg)
 		return;
 
 	if (gdev->big_endian)
-		iowrite32be(val, gdev->base + reg);
+		iowrite32be(val, gdev->base + offset);
 	else
-		iowrite32(val, gdev->base + reg);
+		iowrite32(val, gdev->base + offset);
 }
 
 static ssize_t gisb_arb_get_timeout(struct device *dev,
-- 
2.12.0

[PATCH v3 1/6] bus: brcmstb_gisb: Use register offsets with writes too

[Doug Berger]

This commit corrects the bug introduced in commit f80835875d3d
("bus: brcmstb_gisb: Look up register offsets in a table") such
that gisb_write() translates the register enumeration into an
offset from the base address for writes as well as reads.

Fixes: f80835875d3d ("bus: brcmstb_gisb: Look up register offsets in a table")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 72fe0a5a8bf3..a94598d0945a 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2014 Broadcom Corporation
+ * Copyright (C) 2014-2017 Broadcom
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -127,9 +127,9 @@ static void gisb_write(struct brcmstb_gisb_arb_device *gdev, u32 val, int reg)
 		return;
 
 	if (gdev->big_endian)
-		iowrite32be(val, gdev->base + reg);
+		iowrite32be(val, gdev->base + offset);
 	else
-		iowrite32(val, gdev->base + reg);
+		iowrite32(val, gdev->base + offset);
 }
 
 static ssize_t gisb_arb_get_timeout(struct device *dev,
-- 
2.12.0

[PATCH v3 2/6] bus: brcmstb_gisb: correct support for 64-bit address output

[Doug Berger]

The GISB bus can support addresses beyond 32-bits.  So this commit
corrects support for reading a captured 64-bit address into a 64-bit
variable by obtaining the high bits from the ARB_ERR_CAP_HI_ADDR
register (when present) and then outputting the full 64-bit value.

It also removes unused definitions.

Fixes: 44127b771d9c ("bus: add Broadcom GISB bus arbiter timeout/error handler")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 36 ++++++++++++++++++++----------------
 1 file changed, 20 insertions(+), 16 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index a94598d0945a..017c37b9c7c1 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -37,8 +37,6 @@
 #define  ARB_ERR_CAP_CLEAR		(1 << 0)
 #define  ARB_ERR_CAP_STATUS_TIMEOUT	(1 << 12)
 #define  ARB_ERR_CAP_STATUS_TEA		(1 << 11)
-#define  ARB_ERR_CAP_STATUS_BS_SHIFT	(1 << 2)
-#define  ARB_ERR_CAP_STATUS_BS_MASK	0x3c
 #define  ARB_ERR_CAP_STATUS_WRITE	(1 << 1)
 #define  ARB_ERR_CAP_STATUS_VALID	(1 << 0)
 
@@ -47,7 +45,6 @@ enum {
 	ARB_ERR_CAP_CLR,
 	ARB_ERR_CAP_HI_ADDR,
 	ARB_ERR_CAP_ADDR,
-	ARB_ERR_CAP_DATA,
 	ARB_ERR_CAP_STATUS,
 	ARB_ERR_CAP_MASTER,
 };
@@ -57,7 +54,6 @@ static const int gisb_offsets_bcm7038[] = {
 	[ARB_ERR_CAP_CLR]	= 0x0c4,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0c8,
-	[ARB_ERR_CAP_DATA]	= 0x0cc,
 	[ARB_ERR_CAP_STATUS]	= 0x0d0,
 	[ARB_ERR_CAP_MASTER]	= -1,
 };
@@ -67,7 +63,6 @@ static const int gisb_offsets_bcm7400[] = {
 	[ARB_ERR_CAP_CLR]	= 0x0c8,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0cc,
-	[ARB_ERR_CAP_DATA]	= 0x0d0,
 	[ARB_ERR_CAP_STATUS]	= 0x0d4,
 	[ARB_ERR_CAP_MASTER]	= 0x0d8,
 };
@@ -77,7 +72,6 @@ static const int gisb_offsets_bcm7435[] = {
 	[ARB_ERR_CAP_CLR]	= 0x168,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x16c,
-	[ARB_ERR_CAP_DATA]	= 0x170,
 	[ARB_ERR_CAP_STATUS]	= 0x174,
 	[ARB_ERR_CAP_MASTER]	= 0x178,
 };
@@ -87,7 +81,6 @@ static const int gisb_offsets_bcm7445[] = {
 	[ARB_ERR_CAP_CLR]	= 0x7e4,
 	[ARB_ERR_CAP_HI_ADDR]	= 0x7e8,
 	[ARB_ERR_CAP_ADDR]	= 0x7ec,
-	[ARB_ERR_CAP_DATA]	= 0x7f0,
 	[ARB_ERR_CAP_STATUS]	= 0x7f4,
 	[ARB_ERR_CAP_MASTER]	= 0x7f8,
 };
@@ -109,9 +102,13 @@ static u32 gisb_read(struct brcmstb_gisb_arb_device *gdev, int reg)
 {
 	int offset = gdev->gisb_offsets[reg];
 
-	/* return 1 if the hardware doesn't have ARB_ERR_CAP_MASTER */
-	if (offset == -1)
-		return 1;
+	if (offset < 0) {
+		/* return 1 if the hardware doesn't have ARB_ERR_CAP_MASTER */
+		if (reg == ARB_ERR_CAP_MASTER)
+			return 1;
+		else
+			return 0;
+	}
 
 	if (gdev->big_endian)
 		return ioread32be(gdev->base + offset);
@@ -119,6 +116,16 @@ static u32 gisb_read(struct brcmstb_gisb_arb_device *gdev, int reg)
 		return ioread32(gdev->base + offset);
 }
 
+static u64 gisb_read_address(struct brcmstb_gisb_arb_device *gdev)
+{
+	u64 value;
+
+	value = gisb_read(gdev, ARB_ERR_CAP_ADDR);
+	value |= (u64)gisb_read(gdev, ARB_ERR_CAP_HI_ADDR) << 32;
+
+	return value;
+}
+
 static void gisb_write(struct brcmstb_gisb_arb_device *gdev, u32 val, int reg)
 {
 	int offset = gdev->gisb_offsets[reg];
@@ -185,7 +192,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 					const char *reason)
 {
 	u32 cap_status;
-	unsigned long arb_addr;
+	u64 arb_addr;
 	u32 master;
 	const char *m_name;
 	char m_fmt[11];
@@ -197,10 +204,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 		return 1;
 
 	/* Read the address and master */
-	arb_addr = gisb_read(gdev, ARB_ERR_CAP_ADDR) & 0xffffffff;
-#if (IS_ENABLED(CONFIG_PHYS_ADDR_T_64BIT))
-	arb_addr |= (u64)gisb_read(gdev, ARB_ERR_CAP_HI_ADDR) << 32;
-#endif
+	arb_addr = gisb_read_address(gdev);
 	master = gisb_read(gdev, ARB_ERR_CAP_MASTER);
 
 	m_name = brcmstb_gisb_master_to_str(gdev, master);
@@ -209,7 +213,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 		m_name = m_fmt;
 	}
 
-	pr_crit("%s: %s at 0x%lx [%c %s], core: %s\n",
+	pr_crit("%s: %s at 0x%llx [%c %s], core: %s\n",
 		__func__, reason, arb_addr,
 		cap_status & ARB_ERR_CAP_STATUS_WRITE ? 'W' : 'R',
 		cap_status & ARB_ERR_CAP_STATUS_TIMEOUT ? "timeout" : "",
-- 
2.12.0

[PATCH v3 2/6] bus: brcmstb_gisb: correct support for 64-bit address output

[Doug Berger]

The GISB bus can support addresses beyond 32-bits.  So this commit
corrects support for reading a captured 64-bit address into a 64-bit
variable by obtaining the high bits from the ARB_ERR_CAP_HI_ADDR
register (when present) and then outputting the full 64-bit value.

It also removes unused definitions.

Fixes: 44127b771d9c ("bus: add Broadcom GISB bus arbiter timeout/error handler")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 36 ++++++++++++++++++++----------------
 1 file changed, 20 insertions(+), 16 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index a94598d0945a..017c37b9c7c1 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -37,8 +37,6 @@
 #define  ARB_ERR_CAP_CLEAR		(1 << 0)
 #define  ARB_ERR_CAP_STATUS_TIMEOUT	(1 << 12)
 #define  ARB_ERR_CAP_STATUS_TEA		(1 << 11)
-#define  ARB_ERR_CAP_STATUS_BS_SHIFT	(1 << 2)
-#define  ARB_ERR_CAP_STATUS_BS_MASK	0x3c
 #define  ARB_ERR_CAP_STATUS_WRITE	(1 << 1)
 #define  ARB_ERR_CAP_STATUS_VALID	(1 << 0)
 
@@ -47,7 +45,6 @@ enum {
 	ARB_ERR_CAP_CLR,
 	ARB_ERR_CAP_HI_ADDR,
 	ARB_ERR_CAP_ADDR,
-	ARB_ERR_CAP_DATA,
 	ARB_ERR_CAP_STATUS,
 	ARB_ERR_CAP_MASTER,
 };
@@ -57,7 +54,6 @@ static const int gisb_offsets_bcm7038[] = {
 	[ARB_ERR_CAP_CLR]	= 0x0c4,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0c8,
-	[ARB_ERR_CAP_DATA]	= 0x0cc,
 	[ARB_ERR_CAP_STATUS]	= 0x0d0,
 	[ARB_ERR_CAP_MASTER]	= -1,
 };
@@ -67,7 +63,6 @@ static const int gisb_offsets_bcm7400[] = {
 	[ARB_ERR_CAP_CLR]	= 0x0c8,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x0cc,
-	[ARB_ERR_CAP_DATA]	= 0x0d0,
 	[ARB_ERR_CAP_STATUS]	= 0x0d4,
 	[ARB_ERR_CAP_MASTER]	= 0x0d8,
 };
@@ -77,7 +72,6 @@ static const int gisb_offsets_bcm7435[] = {
 	[ARB_ERR_CAP_CLR]	= 0x168,
 	[ARB_ERR_CAP_HI_ADDR]	= -1,
 	[ARB_ERR_CAP_ADDR]	= 0x16c,
-	[ARB_ERR_CAP_DATA]	= 0x170,
 	[ARB_ERR_CAP_STATUS]	= 0x174,
 	[ARB_ERR_CAP_MASTER]	= 0x178,
 };
@@ -87,7 +81,6 @@ static const int gisb_offsets_bcm7445[] = {
 	[ARB_ERR_CAP_CLR]	= 0x7e4,
 	[ARB_ERR_CAP_HI_ADDR]	= 0x7e8,
 	[ARB_ERR_CAP_ADDR]	= 0x7ec,
-	[ARB_ERR_CAP_DATA]	= 0x7f0,
 	[ARB_ERR_CAP_STATUS]	= 0x7f4,
 	[ARB_ERR_CAP_MASTER]	= 0x7f8,
 };
@@ -109,9 +102,13 @@ static u32 gisb_read(struct brcmstb_gisb_arb_device *gdev, int reg)
 {
 	int offset = gdev->gisb_offsets[reg];
 
-	/* return 1 if the hardware doesn't have ARB_ERR_CAP_MASTER */
-	if (offset == -1)
-		return 1;
+	if (offset < 0) {
+		/* return 1 if the hardware doesn't have ARB_ERR_CAP_MASTER */
+		if (reg == ARB_ERR_CAP_MASTER)
+			return 1;
+		else
+			return 0;
+	}
 
 	if (gdev->big_endian)
 		return ioread32be(gdev->base + offset);
@@ -119,6 +116,16 @@ static u32 gisb_read(struct brcmstb_gisb_arb_device *gdev, int reg)
 		return ioread32(gdev->base + offset);
 }
 
+static u64 gisb_read_address(struct brcmstb_gisb_arb_device *gdev)
+{
+	u64 value;
+
+	value = gisb_read(gdev, ARB_ERR_CAP_ADDR);
+	value |= (u64)gisb_read(gdev, ARB_ERR_CAP_HI_ADDR) << 32;
+
+	return value;
+}
+
 static void gisb_write(struct brcmstb_gisb_arb_device *gdev, u32 val, int reg)
 {
 	int offset = gdev->gisb_offsets[reg];
@@ -185,7 +192,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 					const char *reason)
 {
 	u32 cap_status;
-	unsigned long arb_addr;
+	u64 arb_addr;
 	u32 master;
 	const char *m_name;
 	char m_fmt[11];
@@ -197,10 +204,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 		return 1;
 
 	/* Read the address and master */
-	arb_addr = gisb_read(gdev, ARB_ERR_CAP_ADDR) & 0xffffffff;
-#if (IS_ENABLED(CONFIG_PHYS_ADDR_T_64BIT))
-	arb_addr |= (u64)gisb_read(gdev, ARB_ERR_CAP_HI_ADDR) << 32;
-#endif
+	arb_addr = gisb_read_address(gdev);
 	master = gisb_read(gdev, ARB_ERR_CAP_MASTER);
 
 	m_name = brcmstb_gisb_master_to_str(gdev, master);
@@ -209,7 +213,7 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 		m_name = m_fmt;
 	}
 
-	pr_crit("%s: %s at 0x%lx [%c %s], core: %s\n",
+	pr_crit("%s: %s@0x%llx [%c %s], core: %s\n",
 		__func__, reason, arb_addr,
 		cap_status & ARB_ERR_CAP_STATUS_WRITE ? 'W' : 'R',
 		cap_status & ARB_ERR_CAP_STATUS_TIMEOUT ? "timeout" : "",
-- 
2.12.0

[PATCH v3 3/6] bus: brcmstb_gisb: add notifier handling

[Doug Berger]

Check for GISB arbitration errors through a chained notifier
when a process dies or a kernel panic occurs.  This allows a
meaningful GISB diagnostic message to occur along with other
diagnostic information from the event.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 017c37b9c7c1..a2e1c5c25a3a 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -24,6 +24,9 @@
 #include <linux/of.h>
 #include <linux/bitops.h>
 #include <linux/pm.h>
+#include <linux/kernel.h>
+#include <linux/kdebug.h>
+#include <linux/notifier.h>
 
 #ifdef CONFIG_ARM
 #include <asm/bug.h>
@@ -283,6 +286,36 @@ static irqreturn_t brcmstb_gisb_tea_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+/*
+ * Dump out gisb errors on die or panic.
+ */
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p);
+
+static struct notifier_block gisb_die_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static struct notifier_block gisb_panic_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p)
+{
+	struct brcmstb_gisb_arb_device *gdev;
+	const char *reason = "panic";
+
+	if (self == &gisb_die_notifier)
+		reason = "die";
+
+	/* iterate over each GISB arb registered handlers */
+	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
+		brcmstb_gisb_arb_decode_addr(gdev, reason);
+
+	return NOTIFY_DONE;
+}
+
 static DEVICE_ATTR(gisb_arb_timeout, S_IWUSR | S_IRUGO,
 		gisb_arb_get_timeout, gisb_arb_set_timeout);
 
@@ -390,6 +423,12 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
 
+	if (list_is_singular(&brcmstb_gisb_arb_device_list)) {
+		register_die_notifier(&gisb_die_notifier);
+		atomic_notifier_chain_register(&panic_notifier_list,
+					       &gisb_panic_notifier);
+	}
+
 	dev_info(&pdev->dev, "registered mem: %p, irqs: %d, %d\n",
 			gdev->base, timeout_irq, tea_irq);
 
-- 
2.12.0

[PATCH v3 3/6] bus: brcmstb_gisb: add notifier handling

[Doug Berger]

Check for GISB arbitration errors through a chained notifier
when a process dies or a kernel panic occurs.  This allows a
meaningful GISB diagnostic message to occur along with other
diagnostic information from the event.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 017c37b9c7c1..a2e1c5c25a3a 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -24,6 +24,9 @@
 #include <linux/of.h>
 #include <linux/bitops.h>
 #include <linux/pm.h>
+#include <linux/kernel.h>
+#include <linux/kdebug.h>
+#include <linux/notifier.h>
 
 #ifdef CONFIG_ARM
 #include <asm/bug.h>
@@ -283,6 +286,36 @@ static irqreturn_t brcmstb_gisb_tea_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+/*
+ * Dump out gisb errors on die or panic.
+ */
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p);
+
+static struct notifier_block gisb_die_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static struct notifier_block gisb_panic_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p)
+{
+	struct brcmstb_gisb_arb_device *gdev;
+	const char *reason = "panic";
+
+	if (self == &gisb_die_notifier)
+		reason = "die";
+
+	/* iterate over each GISB arb registered handlers */
+	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
+		brcmstb_gisb_arb_decode_addr(gdev, reason);
+
+	return NOTIFY_DONE;
+}
+
 static DEVICE_ATTR(gisb_arb_timeout, S_IWUSR | S_IRUGO,
 		gisb_arb_get_timeout, gisb_arb_set_timeout);
 
@@ -390,6 +423,12 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
 
+	if (list_is_singular(&brcmstb_gisb_arb_device_list)) {
+		register_die_notifier(&gisb_die_notifier);
+		atomic_notifier_chain_register(&panic_notifier_list,
+					       &gisb_panic_notifier);
+	}
+
 	dev_info(&pdev->dev, "registered mem: %p, irqs: %d, %d\n",
 			gdev->base, timeout_irq, tea_irq);
 
-- 
2.12.0

[PATCH v3 3/6] bus: brcmstb_gisb: add notifier handling

[Doug Berger]

Check for GISB arbitration errors through a chained notifier
when a process dies or a kernel panic occurs.  This allows a
meaningful GISB diagnostic message to occur along with other
diagnostic information from the event.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 39 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 017c37b9c7c1..a2e1c5c25a3a 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -24,6 +24,9 @@
 #include <linux/of.h>
 #include <linux/bitops.h>
 #include <linux/pm.h>
+#include <linux/kernel.h>
+#include <linux/kdebug.h>
+#include <linux/notifier.h>
 
 #ifdef CONFIG_ARM
 #include <asm/bug.h>
@@ -283,6 +286,36 @@ static irqreturn_t brcmstb_gisb_tea_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+/*
+ * Dump out gisb errors on die or panic.
+ */
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p);
+
+static struct notifier_block gisb_die_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static struct notifier_block gisb_panic_notifier = {
+	.notifier_call = dump_gisb_error,
+};
+
+static int dump_gisb_error(struct notifier_block *self, unsigned long v,
+			   void *p)
+{
+	struct brcmstb_gisb_arb_device *gdev;
+	const char *reason = "panic";
+
+	if (self == &gisb_die_notifier)
+		reason = "die";
+
+	/* iterate over each GISB arb registered handlers */
+	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
+		brcmstb_gisb_arb_decode_addr(gdev, reason);
+
+	return NOTIFY_DONE;
+}
+
 static DEVICE_ATTR(gisb_arb_timeout, S_IWUSR | S_IRUGO,
 		gisb_arb_get_timeout, gisb_arb_set_timeout);
 
@@ -390,6 +423,12 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
 
+	if (list_is_singular(&brcmstb_gisb_arb_device_list)) {
+		register_die_notifier(&gisb_die_notifier);
+		atomic_notifier_chain_register(&panic_notifier_list,
+					       &gisb_panic_notifier);
+	}
+
 	dev_info(&pdev->dev, "registered mem: %p, irqs: %d, %d\n",
 			gdev->base, timeout_irq, tea_irq);
 
-- 
2.12.0

[PATCH v3 4/6] bus: brcmstb_gisb: remove low-level ARM hooks

[Doug Berger]

The ARM architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 30 ------------------------------
 1 file changed, 30 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index a2e1c5c25a3a..3fbc116e6b95 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -28,11 +28,6 @@
 #include <linux/kdebug.h>
 #include <linux/notifier.h>
 
-#ifdef CONFIG_ARM
-#include <asm/bug.h>
-#include <asm/signal.h>
-#endif
-
 #ifdef CONFIG_MIPS
 #include <asm/traps.h>
 #endif
@@ -228,27 +223,6 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 	return 0;
 }
 
-#ifdef CONFIG_ARM
-static int brcmstb_bus_error_handler(unsigned long addr, unsigned int fsr,
-				     struct pt_regs *regs)
-{
-	int ret = 0;
-	struct brcmstb_gisb_arb_device *gdev;
-
-	/* iterate over each GISB arb registered handlers */
-	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
-		ret |= brcmstb_gisb_arb_decode_addr(gdev, "bus error");
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	*/
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return ret;
-}
-#endif
-
 #ifdef CONFIG_MIPS
 static int brcmstb_bus_error_handler(struct pt_regs *regs, int is_fixup)
 {
@@ -415,10 +389,6 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 
 	list_add_tail(&gdev->next, &brcmstb_gisb_arb_device_list);
 
-#ifdef CONFIG_ARM
-	hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
-			"imprecise external abort");
-#endif
 #ifdef CONFIG_MIPS
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
-- 
2.12.0

[PATCH v3 4/6] bus: brcmstb_gisb: remove low-level ARM hooks

[Doug Berger]

The ARM architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/bus/brcmstb_gisb.c | 30 ------------------------------
 1 file changed, 30 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index a2e1c5c25a3a..3fbc116e6b95 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -28,11 +28,6 @@
 #include <linux/kdebug.h>
 #include <linux/notifier.h>
 
-#ifdef CONFIG_ARM
-#include <asm/bug.h>
-#include <asm/signal.h>
-#endif
-
 #ifdef CONFIG_MIPS
 #include <asm/traps.h>
 #endif
@@ -228,27 +223,6 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 	return 0;
 }
 
-#ifdef CONFIG_ARM
-static int brcmstb_bus_error_handler(unsigned long addr, unsigned int fsr,
-				     struct pt_regs *regs)
-{
-	int ret = 0;
-	struct brcmstb_gisb_arb_device *gdev;
-
-	/* iterate over each GISB arb registered handlers */
-	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
-		ret |= brcmstb_gisb_arb_decode_addr(gdev, "bus error");
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	*/
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return ret;
-}
-#endif
-
 #ifdef CONFIG_MIPS
 static int brcmstb_bus_error_handler(struct pt_regs *regs, int is_fixup)
 {
@@ -415,10 +389,6 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 
 	list_add_tail(&gdev->next, &brcmstb_gisb_arb_device_list);
 
-#ifdef CONFIG_ARM
-	hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
-			"imprecise external abort");
-#endif
 #ifdef CONFIG_MIPS
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
-- 
2.12.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v3 4/6] bus: brcmstb_gisb: remove low-level ARM hooks

[Doug Berger]

The ARM architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/brcmstb_gisb.c | 30 ------------------------------
 1 file changed, 30 deletions(-)

diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index a2e1c5c25a3a..3fbc116e6b95 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -28,11 +28,6 @@
 #include <linux/kdebug.h>
 #include <linux/notifier.h>
 
-#ifdef CONFIG_ARM
-#include <asm/bug.h>
-#include <asm/signal.h>
-#endif
-
 #ifdef CONFIG_MIPS
 #include <asm/traps.h>
 #endif
@@ -228,27 +223,6 @@ static int brcmstb_gisb_arb_decode_addr(struct brcmstb_gisb_arb_device *gdev,
 	return 0;
 }
 
-#ifdef CONFIG_ARM
-static int brcmstb_bus_error_handler(unsigned long addr, unsigned int fsr,
-				     struct pt_regs *regs)
-{
-	int ret = 0;
-	struct brcmstb_gisb_arb_device *gdev;
-
-	/* iterate over each GISB arb registered handlers */
-	list_for_each_entry(gdev, &brcmstb_gisb_arb_device_list, next)
-		ret |= brcmstb_gisb_arb_decode_addr(gdev, "bus error");
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	*/
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return ret;
-}
-#endif
-
 #ifdef CONFIG_MIPS
 static int brcmstb_bus_error_handler(struct pt_regs *regs, int is_fixup)
 {
@@ -415,10 +389,6 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
 
 	list_add_tail(&gdev->next, &brcmstb_gisb_arb_device_list);
 
-#ifdef CONFIG_ARM
-	hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
-			"imprecise external abort");
-#endif
 #ifdef CONFIG_MIPS
 	board_be_handler = brcmstb_bus_error_handler;
 #endif
-- 
2.12.0

[PATCH v3 5/6] bus: brcmstb_gisb: enable driver for ARM64 architecture

[Doug Berger]

The ARM64 architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 0a52da439abf..d2a5f1184022 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -57,7 +57,7 @@ config ARM_CCN
 
 config BRCMSTB_GISB_ARB
 	bool "Broadcom STB GISB bus arbiter"
-	depends on ARM || MIPS
+	depends on ARM || ARM64 || MIPS
 	default ARCH_BRCMSTB || BMIPS_GENERIC
 	help
 	  Driver for the Broadcom Set Top Box System-on-a-chip internal bus
-- 
2.12.0

[PATCH v3 5/6] bus: brcmstb_gisb: enable driver for ARM64 architecture

[Doug Berger]

The ARM64 architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/bus/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 0a52da439abf..d2a5f1184022 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -57,7 +57,7 @@ config ARM_CCN
 
 config BRCMSTB_GISB_ARB
 	bool "Broadcom STB GISB bus arbiter"
-	depends on ARM || MIPS
+	depends on ARM || ARM64 || MIPS
 	default ARCH_BRCMSTB || BMIPS_GENERIC
 	help
 	  Driver for the Broadcom Set Top Box System-on-a-chip internal bus
-- 
2.12.0

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v3 5/6] bus: brcmstb_gisb: enable driver for ARM64 architecture

[Doug Berger]

The ARM64 architecture can provide meaningful diagnostic
output from the GISB arbiter solely from interrupts and
notifiers without the need to hook the low level fault
handlers.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/bus/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 0a52da439abf..d2a5f1184022 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -57,7 +57,7 @@ config ARM_CCN
 
 config BRCMSTB_GISB_ARB
 	bool "Broadcom STB GISB bus arbiter"
-	depends on ARM || MIPS
+	depends on ARM || ARM64 || MIPS
 	default ARCH_BRCMSTB || BMIPS_GENERIC
 	help
 	  Driver for the Broadcom Set Top Box System-on-a-chip internal bus
-- 
2.12.0

[PATCH v3 6/6] bus: brcmstb_gisb: update to support new revision

[Doug Berger]

The 7278 introduces a new version of this core.  This
commit adds support for that revision.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt |  3 ++-
 drivers/bus/brcmstb_gisb.c                              | 10 ++++++++++
 2 files changed, 12 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
index 1eceefb20f01..8a6c3c2e58fe 100644
--- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
+++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
@@ -3,7 +3,8 @@ Broadcom GISB bus Arbiter controller
 Required properties:
 
 - compatible:
-    "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips
+    "brcm,bcm7278-gisb-arb" for V7 28nm chips
+    "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for other 28nm chips
     "brcm,bcm7435-gisb-arb" for newer 40nm chips
     "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips
     "brcm,bcm7038-gisb-arb" for 130nm chips
diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 3fbc116e6b95..68ac3e93b600 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -56,6 +56,15 @@ static const int gisb_offsets_bcm7038[] = {
 	[ARB_ERR_CAP_MASTER]	= -1,
 };
 
+static const int gisb_offsets_bcm7278[] = {
+	[ARB_TIMER]		= 0x008,
+	[ARB_ERR_CAP_CLR]	= 0x7f8,
+	[ARB_ERR_CAP_HI_ADDR]	= -1,
+	[ARB_ERR_CAP_ADDR]	= 0x7e0,
+	[ARB_ERR_CAP_STATUS]	= 0x7f0,
+	[ARB_ERR_CAP_MASTER]	= 0x7f4,
+};
+
 static const int gisb_offsets_bcm7400[] = {
 	[ARB_TIMER]		= 0x00c,
 	[ARB_ERR_CAP_CLR]	= 0x0c8,
@@ -307,6 +316,7 @@ static const struct of_device_id brcmstb_gisb_arb_of_match[] = {
 	{ .compatible = "brcm,bcm7445-gisb-arb", .data = gisb_offsets_bcm7445 },
 	{ .compatible = "brcm,bcm7435-gisb-arb", .data = gisb_offsets_bcm7435 },
 	{ .compatible = "brcm,bcm7400-gisb-arb", .data = gisb_offsets_bcm7400 },
+	{ .compatible = "brcm,bcm7278-gisb-arb", .data = gisb_offsets_bcm7278 },
 	{ .compatible = "brcm,bcm7038-gisb-arb", .data = gisb_offsets_bcm7038 },
 	{ },
 };
-- 
2.12.0

[PATCH v3 6/6] bus: brcmstb_gisb: update to support new revision

[Doug Berger]

The 7278 introduces a new version of this core.  This
commit adds support for that revision.

Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt |  3 ++-
 drivers/bus/brcmstb_gisb.c                              | 10 ++++++++++
 2 files changed, 12 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
index 1eceefb20f01..8a6c3c2e58fe 100644
--- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
+++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
@@ -3,7 +3,8 @@ Broadcom GISB bus Arbiter controller
 Required properties:
 
 - compatible:
-    "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips
+    "brcm,bcm7278-gisb-arb" for V7 28nm chips
+    "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for other 28nm chips
     "brcm,bcm7435-gisb-arb" for newer 40nm chips
     "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips
     "brcm,bcm7038-gisb-arb" for 130nm chips
diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index 3fbc116e6b95..68ac3e93b600 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -56,6 +56,15 @@ static const int gisb_offsets_bcm7038[] = {
 	[ARB_ERR_CAP_MASTER]	= -1,
 };
 
+static const int gisb_offsets_bcm7278[] = {
+	[ARB_TIMER]		= 0x008,
+	[ARB_ERR_CAP_CLR]	= 0x7f8,
+	[ARB_ERR_CAP_HI_ADDR]	= -1,
+	[ARB_ERR_CAP_ADDR]	= 0x7e0,
+	[ARB_ERR_CAP_STATUS]	= 0x7f0,
+	[ARB_ERR_CAP_MASTER]	= 0x7f4,
+};
+
 static const int gisb_offsets_bcm7400[] = {
 	[ARB_TIMER]		= 0x00c,
 	[ARB_ERR_CAP_CLR]	= 0x0c8,
@@ -307,6 +316,7 @@ static const struct of_device_id brcmstb_gisb_arb_of_match[] = {
 	{ .compatible = "brcm,bcm7445-gisb-arb", .data = gisb_offsets_bcm7445 },
 	{ .compatible = "brcm,bcm7435-gisb-arb", .data = gisb_offsets_bcm7435 },
 	{ .compatible = "brcm,bcm7400-gisb-arb", .data = gisb_offsets_bcm7400 },
+	{ .compatible = "brcm,bcm7278-gisb-arb", .data = gisb_offsets_bcm7278 },
 	{ .compatible = "brcm,bcm7038-gisb-arb", .data = gisb_offsets_bcm7038 },
 	{ },
 };
-- 
2.12.0

Re: [PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Florian Fainelli]

On 03/29/2017 05:29 PM, Doug Berger wrote:
> This patch set contains changes to enable the GISB arbiter driver
> on the latest ARM64 architecture Set-Top Box chips from Broadcom.
> 
> Since the ARM64 architecture does not support the hooking of low
> level fault handlers the driver has been adjusted to depend solely
> on GISB interrupts and notify events to provide diagnostic
> messaging.  The GISB hardware still triggers bus faults for the
> processor so the default low-level aborts will occur and will be
> handled based on the architecture specific kernel implementation.
> 
> While this tends to obsure the GISB error messaging it is still
> reasonable so the same approach is applied to the ARM architecture
> for consistency.
> 
> The patches also correct some issues with the existing driver
> and add the new register map for the GISBv7 hardware first
> appearing in the BCM7278 device.

This all looks great to me, and since there are no more ARM64
dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.

Mark, are you also happy with this v3?

Thanks Doug!

> 
> Changes since v2 at [2]:
>  - Removed code associated with enabling the hooking of ARM64
>    memory faults as well as the code that hooks them for both
>    ARM and ARM64 architectures within the GISB arbiter driver.
>  - Created separate notifiers for die and panic events to
>    prevent list corruption, and substituted the notifier return
>    name for the previous magic number (Thanks Mark!)
> 
> Changes since v1 at [1]:
>  - Removed code associated with hooking SError handling in favor
>    of a registered notifier (Thanks Mark!)
>  - Removed an unnecessary explicit cast (Thanks Gregory!)
> 
> [1] https://lkml.org/lkml/2017/3/24/413
> [2] https://lkml.org/lkml/2017/3/28/1125
> 
> Doug Berger (6):
>   bus: brcmstb_gisb: Use register offsets with writes too
>   bus: brcmstb_gisb: correct support for 64-bit address output
>   bus: brcmstb_gisb: add notifier handling
>   bus: brcmstb_gisb: remove low-level ARM hooks
>   bus: brcmstb_gisb: enable driver for ARM64 architecture
>   bus: brcmstb_gisb: update to support new revision
> 
>  .../devicetree/bindings/bus/brcm,gisb-arb.txt      |   3 +-
>  drivers/bus/Kconfig                                |   2 +-
>  drivers/bus/brcmstb_gisb.c                         | 121 ++++++++++++---------
>  3 files changed, 75 insertions(+), 51 deletions(-)
> 


-- 
Florian

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Florian Fainelli]

On 03/29/2017 05:29 PM, Doug Berger wrote:
> This patch set contains changes to enable the GISB arbiter driver
> on the latest ARM64 architecture Set-Top Box chips from Broadcom.
> 
> Since the ARM64 architecture does not support the hooking of low
> level fault handlers the driver has been adjusted to depend solely
> on GISB interrupts and notify events to provide diagnostic
> messaging.  The GISB hardware still triggers bus faults for the
> processor so the default low-level aborts will occur and will be
> handled based on the architecture specific kernel implementation.
> 
> While this tends to obsure the GISB error messaging it is still
> reasonable so the same approach is applied to the ARM architecture
> for consistency.
> 
> The patches also correct some issues with the existing driver
> and add the new register map for the GISBv7 hardware first
> appearing in the BCM7278 device.

This all looks great to me, and since there are no more ARM64
dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.

Mark, are you also happy with this v3?

Thanks Doug!

> 
> Changes since v2 at [2]:
>  - Removed code associated with enabling the hooking of ARM64
>    memory faults as well as the code that hooks them for both
>    ARM and ARM64 architectures within the GISB arbiter driver.
>  - Created separate notifiers for die and panic events to
>    prevent list corruption, and substituted the notifier return
>    name for the previous magic number (Thanks Mark!)
> 
> Changes since v1 at [1]:
>  - Removed code associated with hooking SError handling in favor
>    of a registered notifier (Thanks Mark!)
>  - Removed an unnecessary explicit cast (Thanks Gregory!)
> 
> [1] https://lkml.org/lkml/2017/3/24/413
> [2] https://lkml.org/lkml/2017/3/28/1125
> 
> Doug Berger (6):
>   bus: brcmstb_gisb: Use register offsets with writes too
>   bus: brcmstb_gisb: correct support for 64-bit address output
>   bus: brcmstb_gisb: add notifier handling
>   bus: brcmstb_gisb: remove low-level ARM hooks
>   bus: brcmstb_gisb: enable driver for ARM64 architecture
>   bus: brcmstb_gisb: update to support new revision
> 
>  .../devicetree/bindings/bus/brcm,gisb-arb.txt      |   3 +-
>  drivers/bus/Kconfig                                |   2 +-
>  drivers/bus/brcmstb_gisb.c                         | 121 ++++++++++++---------
>  3 files changed, 75 insertions(+), 51 deletions(-)
> 


-- 
Florian

Re: [PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Mark Rutland]

On Thu, Mar 30, 2017 at 09:33:32AM -0700, Florian Fainelli wrote:
> On 03/29/2017 05:29 PM, Doug Berger wrote:
> > This patch set contains changes to enable the GISB arbiter driver
> > on the latest ARM64 architecture Set-Top Box chips from Broadcom.
> > 
> > Since the ARM64 architecture does not support the hooking of low
> > level fault handlers the driver has been adjusted to depend solely
> > on GISB interrupts and notify events to provide diagnostic
> > messaging.  The GISB hardware still triggers bus faults for the
> > processor so the default low-level aborts will occur and will be
> > handled based on the architecture specific kernel implementation.
> > 
> > While this tends to obsure the GISB error messaging it is still
> > reasonable so the same approach is applied to the ARM architecture
> > for consistency.
> > 
> > The patches also correct some issues with the existing driver
> > and add the new register map for the GISBv7 hardware first
> > appearing in the BCM7278 device.
> 
> This all looks great to me, and since there are no more ARM64
> dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.
> 
> Mark, are you also happy with this v3?

It looks fine by me.

Thanks,
Mark.

Re: [PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Mark Rutland]

On Thu, Mar 30, 2017 at 09:33:32AM -0700, Florian Fainelli wrote:
> On 03/29/2017 05:29 PM, Doug Berger wrote:
> > This patch set contains changes to enable the GISB arbiter driver
> > on the latest ARM64 architecture Set-Top Box chips from Broadcom.
> > 
> > Since the ARM64 architecture does not support the hooking of low
> > level fault handlers the driver has been adjusted to depend solely
> > on GISB interrupts and notify events to provide diagnostic
> > messaging.  The GISB hardware still triggers bus faults for the
> > processor so the default low-level aborts will occur and will be
> > handled based on the architecture specific kernel implementation.
> > 
> > While this tends to obsure the GISB error messaging it is still
> > reasonable so the same approach is applied to the ARM architecture
> > for consistency.
> > 
> > The patches also correct some issues with the existing driver
> > and add the new register map for the GISBv7 hardware first
> > appearing in the BCM7278 device.
> 
> This all looks great to me, and since there are no more ARM64
> dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.
> 
> Mark, are you also happy with this v3?

It looks fine by me.

Thanks,
Mark.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Mark Rutland]

On Thu, Mar 30, 2017 at 09:33:32AM -0700, Florian Fainelli wrote:
> On 03/29/2017 05:29 PM, Doug Berger wrote:
> > This patch set contains changes to enable the GISB arbiter driver
> > on the latest ARM64 architecture Set-Top Box chips from Broadcom.
> > 
> > Since the ARM64 architecture does not support the hooking of low
> > level fault handlers the driver has been adjusted to depend solely
> > on GISB interrupts and notify events to provide diagnostic
> > messaging.  The GISB hardware still triggers bus faults for the
> > processor so the default low-level aborts will occur and will be
> > handled based on the architecture specific kernel implementation.
> > 
> > While this tends to obsure the GISB error messaging it is still
> > reasonable so the same approach is applied to the ARM architecture
> > for consistency.
> > 
> > The patches also correct some issues with the existing driver
> > and add the new register map for the GISBv7 hardware first
> > appearing in the BCM7278 device.
> 
> This all looks great to me, and since there are no more ARM64
> dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.
> 
> Mark, are you also happy with this v3?

It looks fine by me.

Thanks,
Mark.

Re: [PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Florian Fainelli]

On 03/30/2017 11:19 AM, Mark Rutland wrote:
> On Thu, Mar 30, 2017 at 09:33:32AM -0700, Florian Fainelli wrote:
>> On 03/29/2017 05:29 PM, Doug Berger wrote:
>>> This patch set contains changes to enable the GISB arbiter driver
>>> on the latest ARM64 architecture Set-Top Box chips from Broadcom.
>>>
>>> Since the ARM64 architecture does not support the hooking of low
>>> level fault handlers the driver has been adjusted to depend solely
>>> on GISB interrupts and notify events to provide diagnostic
>>> messaging.  The GISB hardware still triggers bus faults for the
>>> processor so the default low-level aborts will occur and will be
>>> handled based on the architecture specific kernel implementation.
>>>
>>> While this tends to obsure the GISB error messaging it is still
>>> reasonable so the same approach is applied to the ARM architecture
>>> for consistency.
>>>
>>> The patches also correct some issues with the existing driver
>>> and add the new register map for the GISBv7 hardware first
>>> appearing in the BCM7278 device.
>>
>> This all looks great to me, and since there are no more ARM64
>> dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.
>>
>> Mark, are you also happy with this v3?
> 
> It looks fine by me.

Series applied to drivers/next, thanks everyone!
-- 
Florian

[PATCH v3 0/6] bus: brcmstb_gisb: add support for GISBv7 arbiter

[Florian Fainelli]

On 03/30/2017 11:19 AM, Mark Rutland wrote:
> On Thu, Mar 30, 2017 at 09:33:32AM -0700, Florian Fainelli wrote:
>> On 03/29/2017 05:29 PM, Doug Berger wrote:
>>> This patch set contains changes to enable the GISB arbiter driver
>>> on the latest ARM64 architecture Set-Top Box chips from Broadcom.
>>>
>>> Since the ARM64 architecture does not support the hooking of low
>>> level fault handlers the driver has been adjusted to depend solely
>>> on GISB interrupts and notify events to provide diagnostic
>>> messaging.  The GISB hardware still triggers bus faults for the
>>> processor so the default low-level aborts will occur and will be
>>> handled based on the architecture specific kernel implementation.
>>>
>>> While this tends to obsure the GISB error messaging it is still
>>> reasonable so the same approach is applied to the ARM architecture
>>> for consistency.
>>>
>>> The patches also correct some issues with the existing driver
>>> and add the new register map for the GISBv7 hardware first
>>> appearing in the BCM7278 device.
>>
>> This all looks great to me, and since there are no more ARM64
>> dependencies I can take this via the Broadcom ARM/ARM64 SoC pull requests.
>>
>> Mark, are you also happy with this v3?
> 
> It looks fine by me.

Series applied to drivers/next, thanks everyone!
-- 
Florian