[Intel-wired-lan] [next S66 v2 01/11] i40e: update error message when trying to add invalid filters

[Intel-wired-lan] [next S66 v2 01/11] i40e: update error message when trying to add invalid filters

[Alice Michael]

From: Jacob Keller <jacob.e.keller@intel.com>

Re-word the error message displayed when adding a filter with an
invalid flow type. Additionally, report a distinct error message when
the IPv4 protocol is at fault.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
---
 drivers/net/ethernet/intel/i40e/i40e_txrx.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index ebffca0..d45f48c 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -533,14 +533,15 @@ int i40e_add_del_fdir(struct i40e_vsi *vsi,
 			break;
 		default:
 			/* We cannot support masking based on protocol */
-			goto unsupported_flow;
+			dev_info(&pf->pdev->dev, "Unsupported IPv4 protocol 0x%02x\n",
+				 input->ip4_proto);
+			return -EINVAL;
 		}
 		break;
 	default:
-unsupported_flow:
-		dev_info(&pf->pdev->dev, "Could not specify spec type %d\n",
+		dev_info(&pf->pdev->dev, "Unsupported flow type 0x%02x\n",
 			 input->flow_type);
-		ret = -EINVAL;
+		return -EINVAL;
 	}
 
 	/* The buffer allocated here will be normally be freed by
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 02/11] i40e: Swap use of pf->flags and pf->hw_disabled_flags for ATR Eviction

[Alice Michael]

From: Alexander Duyck <alexander.h.duyck@intel.com>

This is a minor cleanup so that we are always updating pf->flags when we
make a change to the private flags instead of updating a mix of either
pf->flags and/or pf->hw_disabled_flags.

In addition I went through and cleaned out all the spots where we were
using the X722 define in regards to this flag.

Lastly since we changed the logic I went through and flushed out any
redundancy and cleaned up the handling of the flags in the Tx path.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
---
 drivers/net/ethernet/intel/i40e/i40e_txrx.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index d45f48c..a9a97dd 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -2263,8 +2263,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 	/* Due to lack of space, no more new filters can be programmed */
 	if (th->syn && (pf->hw_disabled_flags & I40E_FLAG_FD_ATR_ENABLED))
 		return;
-	if ((pf->flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE) &&
-	    (!(pf->hw_disabled_flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE))) {
+	if (pf->flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE) {
 		/* HW ATR eviction will take care of removing filters on FIN
 		 * and RST packets.
 		 */
@@ -2326,8 +2325,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 			I40E_TXD_FLTR_QW1_CNTINDEX_SHIFT) &
 			I40E_TXD_FLTR_QW1_CNTINDEX_MASK;
 
-	if ((pf->flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE) &&
-	    (!(pf->hw_disabled_flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE)))
+	if (pf->flags & I40E_FLAG_HW_ATR_EVICT_CAPABLE)
 		dtype_cmd |= I40E_TXD_FLTR_QW1_ATR_MASK;
 
 	fdir_desc->qindex_flex_ptype_vsi = cpu_to_le32(flex_ptype);
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 02/11] i40e: Swap use of pf->flags and pf->hw_disabled_flags for ATR Eviction

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 02/11] i40e: Swap use of pf->flags and
> pf->hw_disabled_flags for ATR Eviction
> 
> From: Alexander Duyck <alexander.h.duyck@intel.com>
> 
> This is a minor cleanup so that we are always updating pf->flags when we
> make a change to the private flags instead of updating a mix of either
> pf->flags and/or pf->hw_disabled_flags.
> 
> In addition I went through and cleaned out all the spots where we were
> using the X722 define in regards to this flag.
> 
> Lastly since we changed the logic I went through and flushed out any
> redundancy and cleaned up the handling of the flags in the Tx path.
> 
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
> ---
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 03/11] i40e: Decrease the scope of rtnl lock

[Alice Michael]

From: Maciej Sosin <maciej.sosin@intel.com>

Previously rtnl lock was held during whole reset procedure that
was stoping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.

Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
---
 drivers/net/ethernet/intel/i40e/i40e.h         |   2 +-
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c |   6 +-
 drivers/net/ethernet/intel/i40e/i40e_main.c    | 138 +++++++++++++++++--------
 3 files changed, 101 insertions(+), 45 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index 421ea57..686327c 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -837,7 +837,7 @@ void i40e_down(struct i40e_vsi *vsi);
 extern const char i40e_driver_name[];
 extern const char i40e_driver_version_str[];
 void i40e_do_reset_safe(struct i40e_pf *pf, u32 reset_flags);
-void i40e_do_reset(struct i40e_pf *pf, u32 reset_flags);
+void i40e_do_reset(struct i40e_pf *pf, u32 reset_flags, bool lock_acquired);
 int i40e_config_rss(struct i40e_vsi *vsi, u8 *seed, u8 *lut, u16 lut_size);
 int i40e_get_rss(struct i40e_vsi *vsi, u8 *seed, u8 *lut, u16 lut_size);
 void i40e_fill_rss_lut(struct i40e_pf *pf, u8 *lut,
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index c0c1a0c..68c0f20 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -1852,7 +1852,7 @@ static void i40e_diag_test(struct net_device *netdev,
 			 * link then the following link test would have
 			 * to be moved to before the reset
 			 */
-			i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED));
+			i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED), true);
 
 		if (i40e_link_test(netdev, &data[I40E_ETH_TEST_LINK]))
 			eth_test->flags |= ETH_TEST_FL_FAILED;
@@ -1868,7 +1868,7 @@ static void i40e_diag_test(struct net_device *netdev,
 			eth_test->flags |= ETH_TEST_FL_FAILED;
 
 		clear_bit(__I40E_TESTING, &pf->state);
-		i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED));
+		i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED), true);
 
 		if (if_running)
 			i40e_open(netdev);
@@ -4099,7 +4099,7 @@ static int i40e_set_priv_flags(struct net_device *dev, u32 flags)
 	 */
 	if ((changed_flags & I40E_FLAG_VEB_STATS_ENABLED) ||
 	    ((changed_flags & I40E_FLAG_LEGACY_RX) && netif_running(dev)))
-		i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED));
+		i40e_do_reset(pf, BIT(__I40E_PF_RESET_REQUESTED), true);
 
 	return 0;
 }
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 86df489..3d85fc9 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -50,13 +50,16 @@ static const char i40e_copyright[] = "Copyright (c) 2013 - 2014 Intel Corporatio
 
 /* a bit of forward declarations */
 static void i40e_vsi_reinit_locked(struct i40e_vsi *vsi);
-static void i40e_handle_reset_warning(struct i40e_pf *pf);
+static void i40e_handle_reset_warning(struct i40e_pf *pf, bool lock_acquired);
 static int i40e_add_vsi(struct i40e_vsi *vsi);
 static int i40e_add_veb(struct i40e_veb *veb, struct i40e_vsi *vsi);
 static int i40e_setup_pf_switch(struct i40e_pf *pf, bool reinit);
 static int i40e_setup_misc_vector(struct i40e_pf *pf);
 static void i40e_determine_queue_usage(struct i40e_pf *pf);
 static int i40e_setup_pf_filter_control(struct i40e_pf *pf);
+static void i40e_prep_for_reset(struct i40e_pf *pf, bool lock_acquired);
+static int i40e_reset(struct i40e_pf *pf);
+static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired);
 static void i40e_fdir_sb_setup(struct i40e_pf *pf);
 static int i40e_veb_get_bw_info(struct i40e_veb *veb);
 
@@ -5528,6 +5531,8 @@ int i40e_open(struct net_device *netdev)
  * Finish initialization of the VSI.
  *
  * Returns 0 on success, negative value on failure
+ *
+ * Note: expects to be called while under rtnl_lock()
  **/
 int i40e_vsi_open(struct i40e_vsi *vsi)
 {
@@ -5591,7 +5596,7 @@ int i40e_vsi_open(struct i40e_vsi *vsi)
 err_setup_tx:
 	i40e_vsi_free_tx_resources(vsi);
 	if (vsi == pf->vsi[pf->lan_vsi])
-		i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED));
+		i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED), true);
 
 	return err;
 }
@@ -5677,12 +5682,14 @@ int i40e_close(struct net_device *netdev)
  * i40e_do_reset - Start a PF or Core Reset sequence
  * @pf: board private structure
  * @reset_flags: which reset is requested
+ * @lock_acquired: indicates whether or not the lock has been acquired
+ * before this function was called.
  *
  * The essential difference in resets is that the PF Reset
  * doesn't clear the packet buffers, doesn't reset the PE
  * firmware, and doesn't bother the other PFs on the chip.
  **/
-void i40e_do_reset(struct i40e_pf *pf, u32 reset_flags)
+void i40e_do_reset(struct i40e_pf *pf, u32 reset_flags, bool lock_acquired)
 {
 	u32 val;
 
@@ -5728,7 +5735,7 @@ void i40e_do_reset(struct i40e_pf *pf, u32 reset_flags)
 		 * for the Core Reset.
 		 */
 		dev_dbg(&pf->pdev->dev, "PFR requested\n");
-		i40e_handle_reset_warning(pf);
+		i40e_handle_reset_warning(pf, lock_acquired);
 
 	} else if (reset_flags & BIT_ULL(__I40E_REINIT_REQUESTED)) {
 		int v;
@@ -5937,7 +5944,7 @@ static int i40e_handle_lldp_event(struct i40e_pf *pf,
 void i40e_do_reset_safe(struct i40e_pf *pf, u32 reset_flags)
 {
 	rtnl_lock();
-	i40e_do_reset(pf, reset_flags);
+	i40e_do_reset(pf, reset_flags, true);
 	rtnl_unlock();
 }
 
@@ -6339,7 +6346,6 @@ static void i40e_reset_subtask(struct i40e_pf *pf)
 {
 	u32 reset_flags = 0;
 
-	rtnl_lock();
 	if (test_bit(__I40E_REINIT_REQUESTED, &pf->state)) {
 		reset_flags |= BIT(__I40E_REINIT_REQUESTED);
 		clear_bit(__I40E_REINIT_REQUESTED, &pf->state);
@@ -6365,18 +6371,19 @@ static void i40e_reset_subtask(struct i40e_pf *pf)
 	 * precedence before starting a new reset sequence.
 	 */
 	if (test_bit(__I40E_RESET_INTR_RECEIVED, &pf->state)) {
-		i40e_handle_reset_warning(pf);
-		goto unlock;
+		i40e_prep_for_reset(pf, false);
+		i40e_reset(pf);
+		i40e_rebuild(pf, false, false);
 	}
 
 	/* If we're already down or resetting, just bail */
 	if (reset_flags &&
 	    !test_bit(__I40E_DOWN, &pf->state) &&
-	    !test_bit(__I40E_CONFIG_BUSY, &pf->state))
-		i40e_do_reset(pf, reset_flags);
-
-unlock:
-	rtnl_unlock();
+	    !test_bit(__I40E_CONFIG_BUSY, &pf->state)) {
+		rtnl_lock();
+		i40e_do_reset(pf, reset_flags, true);
+		rtnl_unlock();
+	}
 }
 
 /**
@@ -6864,10 +6871,12 @@ static void i40e_fdir_teardown(struct i40e_pf *pf)
 /**
  * i40e_prep_for_reset - prep for the core to reset
  * @pf: board private structure
+ * @lock_acquired: indicates whether or not the lock has been acquired
+ * before this function was called.
  *
  * Close up the VFs and other things in prep for PF Reset.
   **/
-static void i40e_prep_for_reset(struct i40e_pf *pf)
+static void i40e_prep_for_reset(struct i40e_pf *pf, bool lock_acquired)
 {
 	struct i40e_hw *hw = &pf->hw;
 	i40e_status ret = 0;
@@ -6882,7 +6891,12 @@ static void i40e_prep_for_reset(struct i40e_pf *pf)
 	dev_dbg(&pf->pdev->dev, "Tearing down internal switch for reset\n");
 
 	/* quiesce the VSIs and their queues that are not already DOWN */
+	/* pf_quiesce_all_vsi modifies netdev structures -rtnl_lock needed */
+	if (!lock_acquired)
+		rtnl_lock();
 	i40e_pf_quiesce_all_vsi(pf);
+	if (!lock_acquired)
+		rtnl_unlock();
 
 	for (v = 0; v < pf->num_alloc_vsi; v++) {
 		if (pf->vsi[v])
@@ -6917,29 +6931,39 @@ static void i40e_send_version(struct i40e_pf *pf)
 }
 
 /**
- * i40e_reset_and_rebuild - reset and rebuild using a saved config
+ * i40e_reset - wait for core reset to finish reset, reset pf if corer not seen
  * @pf: board private structure
- * @reinit: if the Main VSI needs to re-initialized.
  **/
-static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit)
+static int i40e_reset(struct i40e_pf *pf)
 {
 	struct i40e_hw *hw = &pf->hw;
-	u8 set_fc_aq_fail = 0;
 	i40e_status ret;
-	u32 val;
-	u32 v;
 
-	/* Now we wait for GRST to settle out.
-	 * We don't have to delete the VEBs or VSIs from the hw switch
-	 * because the reset will make them disappear.
-	 */
 	ret = i40e_pf_reset(hw);
 	if (ret) {
 		dev_info(&pf->pdev->dev, "PF reset failed, %d\n", ret);
 		set_bit(__I40E_RESET_FAILED, &pf->state);
-		goto clear_recovery;
+		clear_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state);
+	} else {
+		pf->pfr_count++;
 	}
-	pf->pfr_count++;
+	return ret;
+}
+
+/**
+ * i40e_rebuild - rebuild using a saved config
+ * @pf: board private structure
+ * @reinit: if the Main VSI needs to re-initialized.
+ * @lock_acquired: indicates whether or not the lock has been acquired
+ * before this function was called.
+ **/
+static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired)
+{
+	struct i40e_hw *hw = &pf->hw;
+	u8 set_fc_aq_fail = 0;
+	i40e_status ret;
+	u32 val;
+	int v;
 
 	if (test_bit(__I40E_DOWN, &pf->state))
 		goto clear_recovery;
@@ -6984,9 +7008,11 @@ static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit)
 	}
 #endif /* CONFIG_I40E_DCB */
 	/* do basic switch setup */
+	if (!lock_acquired)
+		rtnl_lock();
 	ret = i40e_setup_pf_switch(pf, reinit);
 	if (ret)
-		goto end_core_reset;
+		goto end_unlock;
 
 	/* The driver only wants link up/down and module qualification
 	 * reports from firmware.  Note the negative logic.
@@ -7057,7 +7083,7 @@ static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit)
 		if (ret) {
 			dev_info(&pf->pdev->dev,
 				 "rebuild of Main VSI failed: %d\n", ret);
-			goto end_core_reset;
+			goto end_unlock;
 		}
 	}
 
@@ -7108,6 +7134,9 @@ static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit)
 	/* tell the firmware that we're starting */
 	i40e_send_version(pf);
 
+end_unlock:
+if (!lock_acquired)
+	rtnl_unlock();
 end_core_reset:
 	clear_bit(__I40E_RESET_FAILED, &pf->state);
 clear_recovery:
@@ -7115,16 +7144,38 @@ static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit)
 }
 
 /**
+ * i40e_reset_and_rebuild - reset and rebuild using a saved config
+ * @pf: board private structure
+ * @reinit: if the Main VSI needs to re-initialized.
+ * @lock_acquired: indicates whether or not the lock has been acquired
+ * before this function was called.
+ **/
+static void i40e_reset_and_rebuild(struct i40e_pf *pf, bool reinit,
+				   bool lock_acquired)
+{
+	int ret;
+	/* Now we wait for GRST to settle out.
+	 * We don't have to delete the VEBs or VSIs from the hw switch
+	 * because the reset will make them disappear.
+	 */
+	ret = i40e_reset(pf);
+	if (!ret)
+		i40e_rebuild(pf, reinit, lock_acquired);
+}
+
+/**
  * i40e_handle_reset_warning - prep for the PF to reset, reset and rebuild
  * @pf: board private structure
  *
  * Close up the VFs and other things in prep for a Core Reset,
  * then get ready to rebuild the world.
+ * @lock_acquired: indicates whether or not the lock has been acquired
+ * before this function was called.
  **/
-static void i40e_handle_reset_warning(struct i40e_pf *pf)
+static void i40e_handle_reset_warning(struct i40e_pf *pf, bool lock_acquired)
 {
-	i40e_prep_for_reset(pf);
-	i40e_reset_and_rebuild(pf, false);
+	i40e_prep_for_reset(pf, lock_acquired);
+	i40e_reset_and_rebuild(pf, false, lock_acquired);
 }
 
 /**
@@ -8421,6 +8472,7 @@ static int i40e_pf_config_rss(struct i40e_pf *pf)
  *
  * returns 0 if rss is not enabled, if enabled returns the final rss queue
  * count which may be different from the requested queue count.
+ * Note: expects to be called while under rtnl_lock()
  **/
 int i40e_reconfig_rss_queues(struct i40e_pf *pf, int queue_count)
 {
@@ -8436,11 +8488,11 @@ int i40e_reconfig_rss_queues(struct i40e_pf *pf, int queue_count)
 		u16 qcount;
 
 		vsi->req_queue_pairs = queue_count;
-		i40e_prep_for_reset(pf);
+		i40e_prep_for_reset(pf, true);
 
 		pf->alloc_rss_size = new_rss_size;
 
-		i40e_reset_and_rebuild(pf, true);
+		i40e_reset_and_rebuild(pf, true, true);
 
 		/* Discard the user configured hash keys and lut, if less
 		 * queues are enabled.
@@ -8816,6 +8868,7 @@ static void i40e_clear_rss_lut(struct i40e_vsi *vsi)
  * i40e_set_features - set the netdev feature flags
  * @netdev: ptr to the netdev being adjusted
  * @features: the feature set that the stack is suggesting
+ * Note: expects to be called while under rtnl_lock()
  **/
 static int i40e_set_features(struct net_device *netdev,
 			     netdev_features_t features)
@@ -8839,7 +8892,7 @@ static int i40e_set_features(struct net_device *netdev,
 	need_reset = i40e_set_ntuple(pf, features);
 
 	if (need_reset)
-		i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED));
+		i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED), true);
 
 	return 0;
 }
@@ -9034,6 +9087,8 @@ static int i40e_ndo_fdb_add(struct ndmsg *ndm, struct nlattr *tb[],
  * is to change the mode then that requires a PF reset to
  * allow rebuild of the components with required hardware
  * bridge mode enabled.
+ *
+ * Note: expects to be called while under rtnl_lock()
  **/
 static int i40e_ndo_bridge_setlink(struct net_device *dev,
 				   struct nlmsghdr *nlh,
@@ -9089,7 +9144,8 @@ static int i40e_ndo_bridge_setlink(struct net_device *dev,
 				pf->flags |= I40E_FLAG_VEB_MODE_ENABLED;
 			else
 				pf->flags &= ~I40E_FLAG_VEB_MODE_ENABLED;
-			i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED));
+			i40e_do_reset(pf, BIT_ULL(__I40E_PF_RESET_REQUESTED),
+				      true);
 			break;
 		}
 	}
@@ -11494,7 +11550,7 @@ static pci_ers_result_t i40e_pci_error_detected(struct pci_dev *pdev,
 	/* shutdown all operations */
 	if (!test_bit(__I40E_SUSPENDED, &pf->state)) {
 		rtnl_lock();
-		i40e_prep_for_reset(pf);
+		i40e_prep_for_reset(pf, true);
 		rtnl_unlock();
 	}
 
@@ -11563,7 +11619,7 @@ static void i40e_pci_error_resume(struct pci_dev *pdev)
 		return;
 
 	rtnl_lock();
-	i40e_handle_reset_warning(pf);
+	i40e_handle_reset_warning(pf, true);
 	rtnl_unlock();
 }
 
@@ -11626,7 +11682,7 @@ static void i40e_shutdown(struct pci_dev *pdev)
 	set_bit(__I40E_SUSPENDED, &pf->state);
 	set_bit(__I40E_DOWN, &pf->state);
 	rtnl_lock();
-	i40e_prep_for_reset(pf);
+	i40e_prep_for_reset(pf, true);
 	rtnl_unlock();
 
 	wr32(hw, I40E_PFPM_APM, (pf->wol_en ? I40E_PFPM_APM_APME_MASK : 0));
@@ -11645,7 +11701,7 @@ static void i40e_shutdown(struct pci_dev *pdev)
 		i40e_enable_mc_magic_wake(pf);
 
 	rtnl_lock();
-	i40e_prep_for_reset(pf);
+	i40e_prep_for_reset(pf, true);
 	rtnl_unlock();
 
 	wr32(hw, I40E_PFPM_APM,
@@ -11679,7 +11735,7 @@ static int i40e_suspend(struct pci_dev *pdev, pm_message_t state)
 		i40e_enable_mc_magic_wake(pf);
 
 	rtnl_lock();
-	i40e_prep_for_reset(pf);
+	i40e_prep_for_reset(pf, true);
 	rtnl_unlock();
 
 	wr32(hw, I40E_PFPM_APM, (pf->wol_en ? I40E_PFPM_APM_APME_MASK : 0));
@@ -11727,7 +11783,7 @@ static int i40e_resume(struct pci_dev *pdev)
 	if (test_and_clear_bit(__I40E_SUSPENDED, &pf->state)) {
 		clear_bit(__I40E_DOWN, &pf->state);
 		rtnl_lock();
-		i40e_reset_and_rebuild(pf, false);
+		i40e_reset_and_rebuild(pf, false, true);
 		rtnl_unlock();
 	}
 
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 03/11] i40e: Decrease the scope of rtnl lock

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Cc: Maciej Sosin <maciej.sosin@intel.com>
> Subject: [Intel-wired-lan] [next S66 v2 03/11] i40e: Decrease the scope of rtnl
> lock
> 
> From: Maciej Sosin <maciej.sosin@intel.com>
> 
> Previously rtnl lock was held during whole reset procedure that was stoping
> other PFs running their reset procedures. In the result reset was not handled
> properly and host reset was the only way to recover.
> 
> Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
> Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
> ---
>  drivers/net/ethernet/intel/i40e/i40e.h         |   2 +-
>  drivers/net/ethernet/intel/i40e/i40e_ethtool.c |   6 +-
>  drivers/net/ethernet/intel/i40e/i40e_main.c    | 138 +++++++++++++++++--
> ------
>  3 files changed, 101 insertions(+), 45 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 04/11] i40e: Simplify i40e_detect_recover_hung_queue logic

[Alice Michael]

From: Alan Brady <alan.brady@intel.com>

This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path.  The previous implementation
set a 'hung bit' which would then get cleared while polling.  If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt.  This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.

Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.

Signed-off-by: Alan Brady <alan.brady@intel.com>
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
---
 drivers/net/ethernet/intel/i40e/i40e.h         |  4 --
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c |  1 -
 drivers/net/ethernet/intel/i40e/i40e_main.c    | 59 +++++---------------------
 drivers/net/ethernet/intel/i40e/i40e_txrx.c    | 12 ++----
 drivers/net/ethernet/intel/i40e/i40e_txrx.h    |  3 +-
 5 files changed, 15 insertions(+), 64 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index 2c12900..e987503 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -613,7 +613,6 @@ struct i40e_vsi {
 	u32 tx_busy;
 	u64 tx_linearize;
 	u64 tx_force_wb;
-	u64 tx_lost_interrupt;
 	u32 rx_buf_failed;
 	u32 rx_page_failed;
 
@@ -699,9 +698,6 @@ struct i40e_q_vector {
 
 	u8 num_ringpairs;	/* total number of ring pairs in vector */
 
-#define I40E_Q_VECTOR_HUNG_DETECT 0 /* Bit Index for hung detection logic */
-	unsigned long hung_detected; /* Set/Reset for hung_detection logic */
-
 	cpumask_t affinity_mask;
 	struct irq_affinity_notify affinity_notify;
 
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index 68c0f20..10325b5 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -89,7 +89,6 @@ static const struct i40e_stats i40e_gstrings_misc_stats[] = {
 	I40E_VSI_STAT("rx_unknown_protocol", eth_stats.rx_unknown_protocol),
 	I40E_VSI_STAT("tx_linearize", tx_linearize),
 	I40E_VSI_STAT("tx_force_wb", tx_force_wb),
-	I40E_VSI_STAT("tx_lost_interrupt", tx_lost_interrupt),
 	I40E_VSI_STAT("rx_alloc_fail", rx_buf_failed),
 	I40E_VSI_STAT("rx_pg_alloc_fail", rx_page_failed),
 };
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 33725a5..fcfab36 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -737,7 +737,6 @@ static void i40e_update_vsi_stats(struct i40e_vsi *vsi)
 	struct i40e_eth_stats *oes;
 	struct i40e_eth_stats *es;     /* device's eth stats */
 	u32 tx_restart, tx_busy;
-	u64 tx_lost_interrupt;
 	struct i40e_ring *p;
 	u32 rx_page, rx_buf;
 	u64 bytes, packets;
@@ -763,7 +762,6 @@ static void i40e_update_vsi_stats(struct i40e_vsi *vsi)
 	rx_b = rx_p = 0;
 	tx_b = tx_p = 0;
 	tx_restart = tx_busy = tx_linearize = tx_force_wb = 0;
-	tx_lost_interrupt = 0;
 	rx_page = 0;
 	rx_buf = 0;
 	rcu_read_lock();
@@ -782,7 +780,6 @@ static void i40e_update_vsi_stats(struct i40e_vsi *vsi)
 		tx_busy += p->tx_stats.tx_busy;
 		tx_linearize += p->tx_stats.tx_linearize;
 		tx_force_wb += p->tx_stats.tx_force_wb;
-		tx_lost_interrupt += p->tx_stats.tx_lost_interrupt;
 
 		/* Rx queue is part of the same block as Tx queue */
 		p = &p[1];
@@ -801,7 +798,6 @@ static void i40e_update_vsi_stats(struct i40e_vsi *vsi)
 	vsi->tx_busy = tx_busy;
 	vsi->tx_linearize = tx_linearize;
 	vsi->tx_force_wb = tx_force_wb;
-	vsi->tx_lost_interrupt = tx_lost_interrupt;
 	vsi->rx_page_failed = rx_page;
 	vsi->rx_buf_failed = rx_buf;
 
@@ -4499,16 +4495,15 @@ static int i40e_pf_wait_queues_disabled(struct i40e_pf *pf)
  * @vsi: Pointer to VSI struct
  *
  * This function checks specified queue for given VSI. Detects hung condition.
- * Sets hung bit since it is two step process. Before next run of service task
- * if napi_poll runs, it reset 'hung' bit for respective q_vector. If not,
- * hung condition remain unchanged and during subsequent run, this function
- * issues SW interrupt to recover from hung condition.
+ * We proactively detect hung TX queues by checking if interrupts are disabled
+ * but there are pending descriptors.  If it appears hung, attempt to recover
+ * by triggering a SW interrupt.
  **/
 static void i40e_detect_recover_hung_queue(int q_idx, struct i40e_vsi *vsi)
 {
 	struct i40e_ring *tx_ring = NULL;
 	struct i40e_pf	*pf;
-	u32 head, val, tx_pending_hw;
+	u32 val, tx_pending;
 	int i;
 
 	pf = vsi->back;
@@ -4534,47 +4529,15 @@ static void i40e_detect_recover_hung_queue(int q_idx, struct i40e_vsi *vsi)
 	else
 		val = rd32(&pf->hw, I40E_PFINT_DYN_CTL0);
 
-	head = i40e_get_head(tx_ring);
+	tx_pending = i40e_get_tx_pending(tx_ring);
 
-	tx_pending_hw = i40e_get_tx_pending(tx_ring, false);
-
-	/* HW is done executing descriptors, updated HEAD write back,
-	 * but SW hasn't processed those descriptors. If interrupt is
-	 * not generated from this point ON, it could result into
-	 * dev_watchdog detecting timeout on those netdev_queue,
-	 * hence proactively trigger SW interrupt.
+	/* Interrupts are disabled and TX pending is non-zero,
+	 * trigger the SW interrupt (don't wait). Worst case
+	 * there will be one extra interrupt which may result
+	 * into not cleaning any queues because queues are cleaned.
 	 */
-	if (tx_pending_hw && (!(val & I40E_PFINT_DYN_CTLN_INTENA_MASK))) {
-		/* NAPI Poll didn't run and clear since it was set */
-		if (test_and_clear_bit(I40E_Q_VECTOR_HUNG_DETECT,
-				       &tx_ring->q_vector->hung_detected)) {
-			netdev_info(vsi->netdev, "VSI_seid %d, Hung TX queue %d, tx_pending_hw: %d, NTC:0x%x, HWB: 0x%x, NTU: 0x%x, TAIL: 0x%x\n",
-				    vsi->seid, q_idx, tx_pending_hw,
-				    tx_ring->next_to_clean, head,
-				    tx_ring->next_to_use,
-				    readl(tx_ring->tail));
-			netdev_info(vsi->netdev, "VSI_seid %d, Issuing force_wb for TX queue %d, Interrupt Reg: 0x%x\n",
-				    vsi->seid, q_idx, val);
-			i40e_force_wb(vsi, tx_ring->q_vector);
-		} else {
-			/* First Chance - detected possible hung */
-			set_bit(I40E_Q_VECTOR_HUNG_DETECT,
-				&tx_ring->q_vector->hung_detected);
-		}
-	}
-
-	/* This is the case where we have interrupts missing,
-	 * so the tx_pending in HW will most likely be 0, but we
-	 * will have tx_pending in SW since the WB happened but the
-	 * interrupt got lost.
-	 */
-	if ((!tx_pending_hw) && i40e_get_tx_pending(tx_ring, true) &&
-	    (!(val & I40E_PFINT_DYN_CTLN_INTENA_MASK))) {
-		local_bh_disable();
-		if (napi_reschedule(&tx_ring->q_vector->napi))
-			tx_ring->tx_stats.tx_lost_interrupt++;
-		local_bh_enable();
-	}
+	if (tx_pending && (!(val & I40E_PFINT_DYN_CTLN_INTENA_MASK)))
+		i40e_force_wb(vsi, tx_ring->q_vector);
 }
 
 /**
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index 9b92d00..b4a7bfc 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -711,19 +711,15 @@ void i40e_free_tx_resources(struct i40e_ring *tx_ring)
 /**
  * i40e_get_tx_pending - how many tx descriptors not processed
  * @tx_ring: the ring of descriptors
- * @in_sw: is tx_pending being checked in SW or HW
  *
  * Since there is no access to the ring head register
  * in XL710, we need to use our local copies
  **/
-u32 i40e_get_tx_pending(struct i40e_ring *ring, bool in_sw)
+u32 i40e_get_tx_pending(struct i40e_ring *ring)
 {
 	u32 head, tail;
 
-	if (!in_sw)
-		head = i40e_get_head(ring);
-	else
-		head = ring->next_to_clean;
+	head = i40e_get_head(ring);
 	tail = readl(ring->tail);
 
 	if (head != tail)
@@ -846,7 +842,7 @@ static bool i40e_clean_tx_irq(struct i40e_vsi *vsi,
 		 * them to be written back in case we stay in NAPI.
 		 * In this mode on X722 we do not enable Interrupt.
 		 */
-		unsigned int j = i40e_get_tx_pending(tx_ring, false);
+		unsigned int j = i40e_get_tx_pending(tx_ring);
 
 		if (budget &&
 		    ((j / WB_STRIDE) == 0) && (j > 0) &&
@@ -2185,8 +2181,6 @@ int i40e_napi_poll(struct napi_struct *napi, int budget)
 		return 0;
 	}
 
-	/* Clear hung_detected bit */
-	clear_bit(I40E_Q_VECTOR_HUNG_DETECT, &q_vector->hung_detected);
 	/* Since the actual Tx work is minimal, we can give the Tx a larger
 	 * budget and be more aggressive about cleaning up the Tx descriptors.
 	 */
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
index 2e876ad..f5de511 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
@@ -328,7 +328,6 @@ struct i40e_tx_queue_stats {
 	u64 tx_done_old;
 	u64 tx_linearize;
 	u64 tx_force_wb;
-	u64 tx_lost_interrupt;
 };
 
 struct i40e_rx_queue_stats {
@@ -480,7 +479,7 @@ void i40e_free_tx_resources(struct i40e_ring *tx_ring);
 void i40e_free_rx_resources(struct i40e_ring *rx_ring);
 int i40e_napi_poll(struct napi_struct *napi, int budget);
 void i40e_force_wb(struct i40e_vsi *vsi, struct i40e_q_vector *q_vector);
-u32 i40e_get_tx_pending(struct i40e_ring *ring, bool in_sw);
+u32 i40e_get_tx_pending(struct i40e_ring *ring);
 int __i40e_maybe_stop_tx(struct i40e_ring *tx_ring, int size);
 bool __i40e_chk_linearize(struct sk_buff *skb);
 
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 04/11] i40e: Simplify i40e_detect_recover_hung_queue logic

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 04/11] i40e: Simplify
> i40e_detect_recover_hung_queue logic
> 
> From: Alan Brady <alan.brady@intel.com>
> 
> This patch greatly reduces the unneeded complexity in the
> i40e_detect_recover_hung_queue code path.  The previous implementation
> set a 'hung bit' which would then get cleared while polling.  If the detection
> routine was called a second time with the bit already set, we would issue a
> software interrupt.  This patch makes it such that if interrupts are disabled
> and we have pending TX descriptors, we trigger a software interrupt since in,
> the worst case, queues are already clean and we have an extra interrupt.
> 
> Additionally this patch removes the workaround for lost interrupts as calling
> napi_reschedule in this context can cause software interrupts to fire on the
> wrong CPU.
> 
> Signed-off-by: Alan Brady <alan.brady@intel.com>
> Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
> ---
>  drivers/net/ethernet/intel/i40e/i40e.h         |  4 --
>  drivers/net/ethernet/intel/i40e/i40e_ethtool.c |  1 -
>  drivers/net/ethernet/intel/i40e/i40e_main.c    | 59 +++++---------------------
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c    | 12 ++----
>  drivers/net/ethernet/intel/i40e/i40e_txrx.h    |  3 +-
>  5 files changed, 15 insertions(+), 64 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 05/11] i40e: allow look-up of MAC address from Open Firmware or IDPROM

[Alice Michael]

From: Jacob Keller <jacob.e.keller@intel.com>

Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
---
 drivers/net/ethernet/intel/i40e/i40e_main.c | 29 ++++++++++++++++-------------
 1 file changed, 16 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 1422809..bae5628 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -9317,10 +9317,15 @@ static int i40e_config_netdev(struct i40e_vsi *vsi)
 	if (vsi->type == I40E_VSI_MAIN) {
 		SET_NETDEV_DEV(netdev, &pf->pdev->dev);
 		ether_addr_copy(mac_addr, hw->mac.perm_addr);
-		/* The following steps are necessary to properly keep track of
-		 * MAC-VLAN filters loaded into firmware - first we remove
-		 * filter that is automatically generated by firmware and then
-		 * add new filter both to the driver hash table and firmware.
+		/* The following steps are necessary for two reasons. First,
+		 * some older NVM configurations load a default MAC-VLAN
+		 * filter that will accept any tagged packet, and we want to
+		 * replace this with a normal filter. Additionally, it is
+		 * possible our MAC address was provided by the platform using
+		 * Open Firmware or similar.
+		 *
+		 * Thus, we need to remove the default filter and install one
+		 * specific to the MAC address.
 		 */
 		i40e_rm_default_mac_filter(vsi, mac_addr);
 		spin_lock_bh(&vsi->mac_filter_hash_lock);
@@ -10825,20 +10830,18 @@ static void i40e_print_features(struct i40e_pf *pf)
 
 /**
  * i40e_get_platform_mac_addr - get platform-specific MAC address
- *
  * @pdev: PCI device information struct
  * @pf: board private structure
  *
- * Look up the MAC address in Open Firmware  on systems that support it,
- * and use IDPROM on SPARC if no OF address is found. On return, the
- * I40E_FLAG_PF_MAC will be wset in pf->flags if a platform-specific value
- * has been selected.
+ * Look up the MAC address for the device. First we'll try
+ * eth_platform_get_mac_address, which will check Open Firmware, or arch
+ * specific fallback. Otherwise, we'll default to the stored value in
+ * firmware.
  **/
 static void i40e_get_platform_mac_addr(struct pci_dev *pdev, struct i40e_pf *pf)
 {
-	pf->flags &= ~I40E_FLAG_PF_MAC;
-	if (!eth_platform_get_mac_address(&pdev->dev, pf->hw.mac.addr))
-		pf->flags |= I40E_FLAG_PF_MAC;
+	if (eth_platform_get_mac_address(&pdev->dev, pf->hw.mac.addr))
+		i40e_get_mac_addr(&pf->hw, pf->hw.mac.addr);
 }
 
 /**
@@ -11057,9 +11060,9 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		i40e_aq_stop_lldp(hw, true, NULL);
 	}
 
-	i40e_get_mac_addr(hw, hw->mac.addr);
 	/* allow a platform config to override the HW addr */
 	i40e_get_platform_mac_addr(pdev, pf);
+
 	if (!is_valid_ether_addr(hw->mac.addr)) {
 		dev_info(&pdev->dev, "invalid MAC address %pM\n", hw->mac.addr);
 		err = -EIO;
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 05/11] i40e: allow look-up of MAC address from Open Firmware or IDPROM

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 05/11] i40e: allow look-up of MAC
> address from Open Firmware or IDPROM
> 
> From: Jacob Keller <jacob.e.keller@intel.com>
> 
> Look up the MAC address from the eth_get_platform_mac_address()
> function first before checking what the firmware provides. We already
> handle the case of re-writing the MAC-VLAN filter, so there is no need to add
> extra code for this. However, update the comment where we do this to
> indicate that it does impact the Open Firmware MAC address case.
> 
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
> ---
>  drivers/net/ethernet/intel/i40e/i40e_main.c | 29 ++++++++++++++++-------
> ------
>  1 file changed, 16 insertions(+), 13 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 06/11] i40e: remove extraneous loop in i40e_vsi_wait_queues_disabled

[Alice Michael]

From: Jacob Keller <jacob.e.keller@intel.com>

We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
---
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index bae5628..da9f0be 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -4431,7 +4431,7 @@ static void i40e_pf_unquiesce_all_vsi(struct i40e_pf *pf)
  * i40e_vsi_wait_queues_disabled - Wait for VSI's queues to be disabled
  * @vsi: the VSI being configured
  *
- * This function waits for the given VSI's queues to be disabled.
+ * Wait until all queues on a given VSI have been disabled.
  **/
 static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
 {
@@ -4440,7 +4440,7 @@ static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
 
 	pf_q = vsi->base_queue;
 	for (i = 0; i < vsi->num_queue_pairs; i++, pf_q++) {
-		/* Check and wait for the disable status of the queue */
+		/* Check and wait for the Tx queue */
 		ret = i40e_pf_txq_wait(pf, pf_q, false);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
@@ -4448,11 +4448,7 @@ static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
 				 vsi->seid, pf_q);
 			return ret;
 		}
-	}
-
-	pf_q = vsi->base_queue;
-	for (i = 0; i < vsi->num_queue_pairs; i++, pf_q++) {
-		/* Check and wait for the disable status of the queue */
+		/* Check and wait for the Tx queue */
 		ret = i40e_pf_rxq_wait(pf, pf_q, false);
 		if (ret) {
 			dev_info(&pf->pdev->dev,
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 06/11] i40e: remove extraneous loop in i40e_vsi_wait_queues_disabled

[Shannon Nelson]

On 4/5/2017 4:50 AM, Alice Michael wrote:
> From: Jacob Keller <jacob.e.keller@intel.com>
>
> We can simply check both Tx and Rx queues in a single loop, rather than
> repeating the loop twice.
>
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
> ---
>  drivers/net/ethernet/intel/i40e/i40e_main.c | 10 +++-------
>  1 file changed, 3 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
> index bae5628..da9f0be 100644
> --- a/drivers/net/ethernet/intel/i40e/i40e_main.c
> +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
> @@ -4431,7 +4431,7 @@ static void i40e_pf_unquiesce_all_vsi(struct i40e_pf *pf)
>   * i40e_vsi_wait_queues_disabled - Wait for VSI's queues to be disabled
>   * @vsi: the VSI being configured
>   *
> - * This function waits for the given VSI's queues to be disabled.
> + * Wait until all queues on a given VSI have been disabled.
>   **/
>  static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
>  {
> @@ -4440,7 +4440,7 @@ static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
>
>  	pf_q = vsi->base_queue;
>  	for (i = 0; i < vsi->num_queue_pairs; i++, pf_q++) {
> -		/* Check and wait for the disable status of the queue */
> +		/* Check and wait for the Tx queue */
>  		ret = i40e_pf_txq_wait(pf, pf_q, false);
>  		if (ret) {
>  			dev_info(&pf->pdev->dev,
> @@ -4448,11 +4448,7 @@ static int i40e_vsi_wait_queues_disabled(struct i40e_vsi *vsi)
>  				 vsi->seid, pf_q);
>  			return ret;
>  		}
> -	}
> -
> -	pf_q = vsi->base_queue;
> -	for (i = 0; i < vsi->num_queue_pairs; i++, pf_q++) {
> -		/* Check and wait for the disable status of the queue */
> +		/* Check and wait for the Tx queue */

s/Tx/Rx/

... but at this point the comments probably aren't even needed as the 
function name makes it rather obvious.

sln

>  		ret = i40e_pf_rxq_wait(pf, pf_q, false);
>  		if (ret) {
>  			dev_info(&pf->pdev->dev,
>

[Intel-wired-lan] [next S66 v2 06/11] i40e: remove extraneous loop in i40e_vsi_wait_queues_disabled

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 06/11] i40e: remove extraneous loop
> in i40e_vsi_wait_queues_disabled
> 
> From: Jacob Keller <jacob.e.keller@intel.com>
> 
> We can simply check both Tx and Rx queues in a single loop, rather than
> repeating the loop twice.
> 
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
> ---
>  drivers/net/ethernet/intel/i40e/i40e_main.c | 10 +++-------
>  1 file changed, 3 insertions(+), 7 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 07/11] i40e: remove I40E_FLAG_NEED_LINK_UPDATE

[Alice Michael]

From: Jacob Keller <jacob.e.keller@intel.com>

The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
---
 drivers/net/ethernet/intel/i40e/i40e.h      | 1 -
 drivers/net/ethernet/intel/i40e/i40e_main.c | 1 -
 drivers/net/ethernet/intel/i40evf/i40evf.h  | 1 -
 3 files changed, 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index 110ef42..ef64dc6 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -389,7 +389,6 @@ struct i40e_pf {
 #define I40E_FLAG_MSIX_ENABLED			BIT_ULL(3)
 #define I40E_FLAG_RSS_ENABLED			BIT_ULL(6)
 #define I40E_FLAG_VMDQ_ENABLED			BIT_ULL(7)
-#define I40E_FLAG_NEED_LINK_UPDATE		BIT_ULL(9)
 #define I40E_FLAG_IWARP_ENABLED			BIT_ULL(10)
 #define I40E_FLAG_CLEAN_ADMINQ			BIT_ULL(14)
 #define I40E_FLAG_FILTER_SYNC			BIT_ULL(15)
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index da9f0be..87dff1b 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -11087,7 +11087,6 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	INIT_WORK(&pf->service_task, i40e_service_task);
 	clear_bit(__I40E_SERVICE_SCHED, &pf->state);
-	pf->flags |= I40E_FLAG_NEED_LINK_UPDATE;
 
 	/* NVM bit on means WoL disabled for the port */
 	i40e_read_nvm_word(hw, I40E_SR_NVM_WAKE_ON_LAN, &wol_nvm_bits);
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf.h b/drivers/net/ethernet/intel/i40evf/i40evf.h
index d61ecf6..35ded19 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf.h
+++ b/drivers/net/ethernet/intel/i40evf/i40evf.h
@@ -205,7 +205,6 @@ struct i40evf_adapter {
 #define I40EVF_FLAG_IN_NETPOLL			BIT(4)
 #define I40EVF_FLAG_IMIR_ENABLED		BIT(5)
 #define I40EVF_FLAG_MQ_CAPABLE			BIT(6)
-#define I40EVF_FLAG_NEED_LINK_UPDATE		BIT(7)
 #define I40EVF_FLAG_PF_COMMS_FAILED		BIT(8)
 #define I40EVF_FLAG_RESET_PENDING		BIT(9)
 #define I40EVF_FLAG_RESET_NEEDED		BIT(10)
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 07/11] i40e: remove I40E_FLAG_NEED_LINK_UPDATE

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 07/11] i40e: remove
> I40E_FLAG_NEED_LINK_UPDATE
> 
> From: Jacob Keller <jacob.e.keller@intel.com>
> 
> The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
> definitions.
> 
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
> ---
>  drivers/net/ethernet/intel/i40e/i40e.h      | 1 -
>  drivers/net/ethernet/intel/i40e/i40e_main.c | 1 -
> drivers/net/ethernet/intel/i40evf/i40evf.h  | 1 -
>  3 files changed, 3 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 08/11] i40e: clean up historic deprecated flag definitions

[Alice Michael]

From: Jacob Keller <jacob.e.keller@intel.com>

Since an early commit a few flags have no longer
been used. Remove these definitions to reduce code clutter.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
---
 drivers/net/ethernet/intel/i40e/i40e.h | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index ef64dc6..e987503 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -390,11 +390,8 @@ struct i40e_pf {
 #define I40E_FLAG_RSS_ENABLED			BIT_ULL(6)
 #define I40E_FLAG_VMDQ_ENABLED			BIT_ULL(7)
 #define I40E_FLAG_IWARP_ENABLED			BIT_ULL(10)
-#define I40E_FLAG_CLEAN_ADMINQ			BIT_ULL(14)
 #define I40E_FLAG_FILTER_SYNC			BIT_ULL(15)
 #define I40E_FLAG_SERVICE_CLIENT_REQUESTED	BIT_ULL(16)
-#define I40E_FLAG_PROCESS_MDD_EVENT		BIT_ULL(17)
-#define I40E_FLAG_PROCESS_VFLR_EVENT		BIT_ULL(18)
 #define I40E_FLAG_SRIOV_ENABLED			BIT_ULL(19)
 #define I40E_FLAG_DCB_ENABLED			BIT_ULL(20)
 #define I40E_FLAG_FD_SB_ENABLED			BIT_ULL(21)
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 08/11] i40e: clean up historic deprecated flag definitions

[Shannon Nelson]

On 4/5/2017 4:51 AM, Alice Michael wrote:
> From: Jacob Keller <jacob.e.keller@intel.com>
>
> Since an early commit a few flags have no longer
> been used. Remove these definitions to reduce code clutter.

Why not combine this with the previous patch?
sln

>
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
> ---
>  drivers/net/ethernet/intel/i40e/i40e.h | 3 ---
>  1 file changed, 3 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
> index ef64dc6..e987503 100644
> --- a/drivers/net/ethernet/intel/i40e/i40e.h
> +++ b/drivers/net/ethernet/intel/i40e/i40e.h
> @@ -390,11 +390,8 @@ struct i40e_pf {
>  #define I40E_FLAG_RSS_ENABLED			BIT_ULL(6)
>  #define I40E_FLAG_VMDQ_ENABLED			BIT_ULL(7)
>  #define I40E_FLAG_IWARP_ENABLED			BIT_ULL(10)
> -#define I40E_FLAG_CLEAN_ADMINQ			BIT_ULL(14)
>  #define I40E_FLAG_FILTER_SYNC			BIT_ULL(15)
>  #define I40E_FLAG_SERVICE_CLIENT_REQUESTED	BIT_ULL(16)
> -#define I40E_FLAG_PROCESS_MDD_EVENT		BIT_ULL(17)
> -#define I40E_FLAG_PROCESS_VFLR_EVENT		BIT_ULL(18)
>  #define I40E_FLAG_SRIOV_ENABLED			BIT_ULL(19)
>  #define I40E_FLAG_DCB_ENABLED			BIT_ULL(20)
>  #define I40E_FLAG_FD_SB_ENABLED			BIT_ULL(21)
>

[Intel-wired-lan] [next S66 v2 08/11] i40e: clean up historic deprecated flag definitions

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 08/11] i40e: clean up historic
> deprecated flag definitions
> 
> From: Jacob Keller <jacob.e.keller@intel.com>
> 
> Since an early commit a few flags have no longer been used. Remove these
> definitions to reduce code clutter.
> 
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: I3589be4622574e747013cd4dc403e18b039f4965
> ---
>  drivers/net/ethernet/intel/i40e/i40e.h | 3 ---
>  1 file changed, 3 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 09/11] i40e/i40evf: Add support for using order 1 pages with a 3K buffer

[Alice Michael]

From: Alexander Duyck <alexander.h.duyck@intel.com>

There are situations where adding padding to the front and back of an Rx
buffer will require that we add additional padding.  Specifically if
NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would need
to use 2K buffers which leaves us with no room for the padding.

To preemptively address these cases I am adding support for 3K buffers to
the Rx path so that we can provide the additional padding needed in the
event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7
---
 drivers/net/ethernet/intel/i40e/i40e_main.c     |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_txrx.c     | 27 +++++++++++++------------
 drivers/net/ethernet/intel/i40e/i40e_txrx.h     | 12 +++++++++++
 drivers/net/ethernet/intel/i40evf/i40e_txrx.c   | 27 +++++++++++++------------
 drivers/net/ethernet/intel/i40evf/i40e_txrx.h   | 12 +++++++++++
 drivers/net/ethernet/intel/i40evf/i40evf_main.c |  6 ++++++
 6 files changed, 60 insertions(+), 27 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 89f3659..859c8e1 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -3085,7 +3085,8 @@ static int i40e_vsi_configure_rx(struct i40e_vsi *vsi)
 #endif
 	} else {
 		vsi->max_frame = I40E_MAX_RXBUFFER;
-		vsi->rx_buf_len = I40E_RXBUFFER_2048;
+		vsi->rx_buf_len = (PAGE_SIZE < 8192) ? I40E_RXBUFFER_3072 :
+						       I40E_RXBUFFER_2048;
 	}
 
 	/* set up individual rings */
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index e95428c..bee1672 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -1138,14 +1138,15 @@ void i40e_clean_rx_ring(struct i40e_ring *rx_ring)
 		dma_sync_single_range_for_cpu(rx_ring->dev,
 					      rx_bi->dma,
 					      rx_bi->page_offset,
-					      I40E_RXBUFFER_2048,
+					      rx_ring->rx_buf_len,
 					      DMA_FROM_DEVICE);
 
 		/* free resources associated with mapping */
 		dma_unmap_page_attrs(rx_ring->dev, rx_bi->dma,
-				     PAGE_SIZE,
+				     i40e_rx_pg_size(rx_ring),
 				     DMA_FROM_DEVICE,
 				     I40E_RX_DMA_ATTR);
+
 		__page_frag_cache_drain(rx_bi->page, rx_bi->pagecnt_bias);
 
 		rx_bi->page = NULL;
@@ -1267,7 +1268,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 	}
 
 	/* alloc new page for storage */
-	page = dev_alloc_page();
+	page = dev_alloc_pages(i40e_rx_pg_order(rx_ring));
 	if (unlikely(!page)) {
 		rx_ring->rx_stats.alloc_page_failed++;
 		return false;
@@ -1275,7 +1276,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 
 	/* map page for use */
 	dma = dma_map_page_attrs(rx_ring->dev, page, 0,
-				 PAGE_SIZE,
+				 i40e_rx_pg_size(rx_ring),
 				 DMA_FROM_DEVICE,
 				 I40E_RX_DMA_ATTR);
 
@@ -1283,7 +1284,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 	 * there isn't much point in holding memory we can't use
 	 */
 	if (dma_mapping_error(rx_ring->dev, dma)) {
-		__free_pages(page, 0);
+		__free_pages(page, i40e_rx_pg_order(rx_ring));
 		rx_ring->rx_stats.alloc_page_failed++;
 		return false;
 	}
@@ -1343,7 +1344,7 @@ bool i40e_alloc_rx_buffers(struct i40e_ring *rx_ring, u16 cleaned_count)
 		/* sync the buffer for use by the device */
 		dma_sync_single_range_for_device(rx_ring->dev, bi->dma,
 						 bi->page_offset,
-						 I40E_RXBUFFER_2048,
+						 rx_ring->rx_buf_len,
 						 DMA_FROM_DEVICE);
 
 		/* Refresh the desc even if buffer_addrs didn't change
@@ -1645,9 +1646,6 @@ static inline bool i40e_page_is_reusable(struct page *page)
  **/
 static bool i40e_can_reuse_rx_page(struct i40e_rx_buffer *rx_buffer)
 {
-#if (PAGE_SIZE >= 8192)
-	unsigned int last_offset = PAGE_SIZE - I40E_RXBUFFER_2048;
-#endif
 	unsigned int pagecnt_bias = rx_buffer->pagecnt_bias;
 	struct page *page = rx_buffer->page;
 
@@ -1660,7 +1658,9 @@ static bool i40e_can_reuse_rx_page(struct i40e_rx_buffer *rx_buffer)
 	if (unlikely((page_count(page) - pagecnt_bias) > 1))
 		return false;
 #else
-	if (rx_buffer->page_offset > last_offset)
+#define I40E_LAST_OFFSET \
+	(SKB_WITH_OVERHEAD(PAGE_SIZE) - I40E_RXBUFFER_2048)
+	if (rx_buffer->page_offset > I40E_LAST_OFFSET)
 		return false;
 #endif
 
@@ -1694,7 +1694,7 @@ static void i40e_add_rx_frag(struct i40e_ring *rx_ring,
 			     unsigned int size)
 {
 #if (PAGE_SIZE < 8192)
-	unsigned int truesize = I40E_RXBUFFER_2048;
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
 	unsigned int truesize = SKB_DATA_ALIGN(size);
 #endif
@@ -1755,7 +1755,7 @@ static struct sk_buff *i40e_construct_skb(struct i40e_ring *rx_ring,
 {
 	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
 #if (PAGE_SIZE < 8192)
-	unsigned int truesize = I40E_RXBUFFER_2048;
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
 	unsigned int truesize = SKB_DATA_ALIGN(size);
 #endif
@@ -1821,7 +1821,8 @@ static void i40e_put_rx_buffer(struct i40e_ring *rx_ring,
 		rx_ring->rx_stats.page_reuse_count++;
 	} else {
 		/* we are not reusing the buffer so unmap it */
-		dma_unmap_page_attrs(rx_ring->dev, rx_buffer->dma, PAGE_SIZE,
+		dma_unmap_page_attrs(rx_ring->dev, rx_buffer->dma,
+				     i40e_rx_pg_size(rx_ring),
 				     DMA_FROM_DEVICE, I40E_RX_DMA_ATTR);
 		__page_frag_cache_drain(rx_buffer->page,
 					rx_buffer->pagecnt_bias);
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
index bc66ec4..2f61853 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
@@ -119,6 +119,7 @@ enum i40e_dyn_idx_t {
 #define I40E_RXBUFFER_256   256
 #define I40E_RXBUFFER_1536  1536  /* 128B aligned standard Ethernet frame */
 #define I40E_RXBUFFER_2048  2048
+#define I40E_RXBUFFER_3072  3072  /* Used for large frames w/ padding */
 #define I40E_MAX_RXBUFFER   9728  /* largest size for single descriptor */
 
 /* NOTE: netdev_alloc_skb reserves up to 64 bytes, NET_IP_ALIGN means we
@@ -389,6 +390,17 @@ struct i40e_ring_container {
 #define i40e_for_each_ring(pos, head) \
 	for (pos = (head).ring; pos != NULL; pos = pos->next)
 
+static inline unsigned int i40e_rx_pg_order(struct i40e_ring *ring)
+{
+#if (PAGE_SIZE < 8192)
+	if (ring->rx_buf_len > (PAGE_SIZE / 2))
+		return 1;
+#endif
+	return 0;
+}
+
+#define i40e_rx_pg_size(_ring) (PAGE_SIZE << i40e_rx_pg_order(_ring))
+
 bool i40e_alloc_rx_buffers(struct i40e_ring *rxr, u16 cleaned_count);
 netdev_tx_t i40e_lan_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
 void i40e_clean_tx_ring(struct i40e_ring *tx_ring);
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index 95e383a..6b60c19 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -509,14 +509,15 @@ void i40evf_clean_rx_ring(struct i40e_ring *rx_ring)
 		dma_sync_single_range_for_cpu(rx_ring->dev,
 					      rx_bi->dma,
 					      rx_bi->page_offset,
-					      I40E_RXBUFFER_2048,
+					      rx_ring->rx_buf_len,
 					      DMA_FROM_DEVICE);
 
 		/* free resources associated with mapping */
 		dma_unmap_page_attrs(rx_ring->dev, rx_bi->dma,
-				     PAGE_SIZE,
+				     i40e_rx_pg_size(rx_ring),
 				     DMA_FROM_DEVICE,
 				     I40E_RX_DMA_ATTR);
+
 		__page_frag_cache_drain(rx_bi->page, rx_bi->pagecnt_bias);
 
 		rx_bi->page = NULL;
@@ -638,7 +639,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 	}
 
 	/* alloc new page for storage */
-	page = dev_alloc_page();
+	page = dev_alloc_pages(i40e_rx_pg_order(rx_ring));
 	if (unlikely(!page)) {
 		rx_ring->rx_stats.alloc_page_failed++;
 		return false;
@@ -646,7 +647,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 
 	/* map page for use */
 	dma = dma_map_page_attrs(rx_ring->dev, page, 0,
-				 PAGE_SIZE,
+				 i40e_rx_pg_size(rx_ring),
 				 DMA_FROM_DEVICE,
 				 I40E_RX_DMA_ATTR);
 
@@ -654,7 +655,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 	 * there isn't much point in holding memory we can't use
 	 */
 	if (dma_mapping_error(rx_ring->dev, dma)) {
-		__free_pages(page, 0);
+		__free_pages(page, i40e_rx_pg_order(rx_ring));
 		rx_ring->rx_stats.alloc_page_failed++;
 		return false;
 	}
@@ -714,7 +715,7 @@ bool i40evf_alloc_rx_buffers(struct i40e_ring *rx_ring, u16 cleaned_count)
 		/* sync the buffer for use by the device */
 		dma_sync_single_range_for_device(rx_ring->dev, bi->dma,
 						 bi->page_offset,
-						 I40E_RXBUFFER_2048,
+						 rx_ring->rx_buf_len,
 						 DMA_FROM_DEVICE);
 
 		/* Refresh the desc even if buffer_addrs didn't change
@@ -1006,9 +1007,6 @@ static inline bool i40e_page_is_reusable(struct page *page)
  **/
 static bool i40e_can_reuse_rx_page(struct i40e_rx_buffer *rx_buffer)
 {
-#if (PAGE_SIZE >= 8192)
-	unsigned int last_offset = PAGE_SIZE - I40E_RXBUFFER_2048;
-#endif
 	unsigned int pagecnt_bias = rx_buffer->pagecnt_bias;
 	struct page *page = rx_buffer->page;
 
@@ -1021,7 +1019,9 @@ static bool i40e_can_reuse_rx_page(struct i40e_rx_buffer *rx_buffer)
 	if (unlikely((page_count(page) - pagecnt_bias) > 1))
 		return false;
 #else
-	if (rx_buffer->page_offset > last_offset)
+#define I40E_LAST_OFFSET \
+	(SKB_WITH_OVERHEAD(PAGE_SIZE) - I40E_RXBUFFER_2048)
+	if (rx_buffer->page_offset > I40E_LAST_OFFSET)
 		return false;
 #endif
 
@@ -1055,7 +1055,7 @@ static void i40e_add_rx_frag(struct i40e_ring *rx_ring,
 			     unsigned int size)
 {
 #if (PAGE_SIZE < 8192)
-	unsigned int truesize = I40E_RXBUFFER_2048;
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
 	unsigned int truesize = SKB_DATA_ALIGN(size);
 #endif
@@ -1116,7 +1116,7 @@ static struct sk_buff *i40e_construct_skb(struct i40e_ring *rx_ring,
 {
 	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
 #if (PAGE_SIZE < 8192)
-	unsigned int truesize = I40E_RXBUFFER_2048;
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
 	unsigned int truesize = SKB_DATA_ALIGN(size);
 #endif
@@ -1182,7 +1182,8 @@ static void i40e_put_rx_buffer(struct i40e_ring *rx_ring,
 		rx_ring->rx_stats.page_reuse_count++;
 	} else {
 		/* we are not reusing the buffer so unmap it */
-		dma_unmap_page_attrs(rx_ring->dev, rx_buffer->dma, PAGE_SIZE,
+		dma_unmap_page_attrs(rx_ring->dev, rx_buffer->dma,
+				     i40e_rx_pg_size(rx_ring),
 				     DMA_FROM_DEVICE, I40E_RX_DMA_ATTR);
 		__page_frag_cache_drain(rx_buffer->page,
 					rx_buffer->pagecnt_bias);
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
index 3bb4d73..dc82f65 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
@@ -106,6 +106,7 @@ enum i40e_dyn_idx_t {
 #define I40E_RXBUFFER_256   256
 #define I40E_RXBUFFER_1536  1536  /* 128B aligned standard Ethernet frame */
 #define I40E_RXBUFFER_2048  2048
+#define I40E_RXBUFFER_3072  3072  /* Used for large frames w/ padding */
 #define I40E_MAX_RXBUFFER   9728  /* largest size for single descriptor */
 
 /* NOTE: netdev_alloc_skb reserves up to 64 bytes, NET_IP_ALIGN means we
@@ -376,6 +377,17 @@ struct i40e_ring_container {
 #define i40e_for_each_ring(pos, head) \
 	for (pos = (head).ring; pos != NULL; pos = pos->next)
 
+static inline unsigned int i40e_rx_pg_order(struct i40e_ring *ring)
+{
+#if (PAGE_SIZE < 8192)
+	if (ring->rx_buf_len > (PAGE_SIZE / 2))
+		return 1;
+#endif
+	return 0;
+}
+
+#define i40e_rx_pg_size(_ring) (PAGE_SIZE << i40e_rx_pg_order(_ring))
+
 bool i40evf_alloc_rx_buffers(struct i40e_ring *rxr, u16 cleaned_count);
 netdev_tx_t i40evf_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
 void i40evf_clean_tx_ring(struct i40e_ring *tx_ring);
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf_main.c b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
index 2f8f599..95d5c04 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf_main.c
+++ b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
@@ -694,6 +694,12 @@ static void i40evf_configure_rx(struct i40evf_adapter *adapter)
 	/* Legacy Rx will always default to a 2048 buffer size. */
 #if (PAGE_SIZE < 8192)
 	if (!(adapter->flags & I40EVF_FLAG_LEGACY_RX)) {
+		/* For jumbo frames on systems with 4K pages we have to use
+		 * an order 1 page, so we might as well increase the size
+		 * of our Rx buffer to make better use of the available space
+		 */
+		rx_buf_len = I40E_RXBUFFER_3072;
+
 		/* We use a 1536 buffer size for configurations with
 		 * standard Ethernet mtu.  On x86 this gives us enough room
 		 * for shared info and 192 bytes of padding.
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 09/11] i40e/i40evf: Add support for using order 1 pages with a 3K buffer

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 09/11] i40e/i40evf: Add support for
> using order 1 pages with a 3K buffer
> 
> From: Alexander Duyck <alexander.h.duyck@intel.com>
> 
> There are situations where adding padding to the front and back of an Rx
> buffer will require that we add additional padding.  Specifically if
> NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would
> need to use 2K buffers which leaves us with no room for the padding.
> 
> To preemptively address these cases I am adding support for 3K buffers to
> the Rx path so that we can provide the additional padding needed in the
> event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
> 
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7
> ---
>  drivers/net/ethernet/intel/i40e/i40e_main.c     |  3 ++-
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c     | 27 +++++++++++++----------
> --
>  drivers/net/ethernet/intel/i40e/i40e_txrx.h     | 12 +++++++++++
>  drivers/net/ethernet/intel/i40evf/i40e_txrx.c   | 27 +++++++++++++---------
> ---
>  drivers/net/ethernet/intel/i40evf/i40e_txrx.h   | 12 +++++++++++
>  drivers/net/ethernet/intel/i40evf/i40evf_main.c |  6 ++++++
>  6 files changed, 60 insertions(+), 27 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 10/11] i40e/i40evf: Add support for padding start of frames

[Alice Michael]

From: Alexander Duyck <alexander.h.duyck@intel.com>

This patch adds padding to the start of frames to make room for headroom
for us to eventually start using build_skb.  Right now we guarantee at
least NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
available.  For example on x86 the headroom should be 192 bytes.

On systems that have too large of a cache line size to support storing 1.5K
padding and shared info we default to using 3K buffers and reserve
everything that isn't used for skb_shared_info or the data buffer for
headroom.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a
---
 drivers/net/ethernet/intel/i40e/i40e_main.c     |  9 +++-
 drivers/net/ethernet/intel/i40e/i40e_txrx.c     | 15 +++++-
 drivers/net/ethernet/intel/i40e/i40e_txrx.h     | 70 ++++++++++++++++++++++++-
 drivers/net/ethernet/intel/i40evf/i40e_txrx.c   | 15 +++++-
 drivers/net/ethernet/intel/i40evf/i40e_txrx.h   | 70 ++++++++++++++++++++++++-
 drivers/net/ethernet/intel/i40evf/i40evf_main.c |  8 ++-
 6 files changed, 179 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 859c8e1..273f9aa 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -3038,6 +3038,12 @@ static int i40e_configure_rx_ring(struct i40e_ring *ring)
 		return -ENOMEM;
 	}
 
+	/* configure Rx buffer alignment */
+	if (!vsi->netdev || (vsi->back->flags & I40E_FLAG_LEGACY_RX))
+		clear_ring_build_skb_enabled(ring);
+	else
+		set_ring_build_skb_enabled(ring);
+
 	/* cache tail for quicker writes, and clear the reg before use */
 	ring->tail = hw->hw_addr + I40E_QRX_TAIL(pf_q);
 	writel(0, ring->tail);
@@ -3079,7 +3085,8 @@ static int i40e_vsi_configure_rx(struct i40e_vsi *vsi)
 		vsi->max_frame = I40E_MAX_RXBUFFER;
 		vsi->rx_buf_len = I40E_RXBUFFER_2048;
 #if (PAGE_SIZE < 8192)
-	} else if (vsi->netdev->mtu <= ETH_DATA_LEN) {
+	} else if (!I40E_2K_TOO_SMALL_WITH_PADDING &&
+		   (vsi->netdev->mtu <= ETH_DATA_LEN)) {
 		vsi->max_frame = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
 		vsi->rx_buf_len = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
 #endif
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index bee1672..4b31aec 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -1248,6 +1248,17 @@ static inline void i40e_release_rx_desc(struct i40e_ring *rx_ring, u32 val)
 }
 
 /**
+ * i40e_rx_offset - Return expected offset into page to access data
+ * @rx_ring: Ring we are requesting offset of
+ *
+ * Returns the offset value for ring into the data buffer.
+ */
+static inline unsigned int i40e_rx_offset(struct i40e_ring *rx_ring)
+{
+	return ring_uses_build_skb(rx_ring) ? I40E_SKB_PAD : 0;
+}
+
+/**
  * i40e_alloc_mapped_page - recycle or make a new page
  * @rx_ring: ring to use
  * @bi: rx_buffer struct to modify
@@ -1291,7 +1302,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 
 	bi->dma = dma;
 	bi->page = page;
-	bi->page_offset = 0;
+	bi->page_offset = i40e_rx_offset(rx_ring);
 
 	/* initialize pagecnt_bias to 1 representing we fully own page */
 	bi->pagecnt_bias = 1;
@@ -1696,7 +1707,7 @@ static void i40e_add_rx_frag(struct i40e_ring *rx_ring,
 #if (PAGE_SIZE < 8192)
 	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
-	unsigned int truesize = SKB_DATA_ALIGN(size);
+	unsigned int truesize =	SKB_DATA_ALIGN(size + i40e_rx_offset(rx_ring));
 #endif
 
 	skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, rx_buffer->page,
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
index 2f61853..f5de511 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
@@ -135,6 +135,58 @@ enum i40e_dyn_idx_t {
 #define I40E_RX_DMA_ATTR \
 	(DMA_ATTR_SKIP_CPU_SYNC | DMA_ATTR_WEAK_ORDERING)
 
+/* Attempt to maximize the headroom available for incoming frames.  We
+ * use a 2K buffer for receives and need 1536/1534 to store the data for
+ * the frame.  This leaves us with 512 bytes of room.  From that we need
+ * to deduct the space needed for the shared info and the padding needed
+ * to IP align the frame.
+ *
+ * Note: For cache line sizes 256 or larger this value is going to end
+ *	 up negative.  In these cases we should fall back to the legacy
+ *	 receive path.
+ */
+#if (PAGE_SIZE < 8192)
+#define I40E_2K_TOO_SMALL_WITH_PADDING \
+((NET_SKB_PAD + I40E_RXBUFFER_1536) > SKB_WITH_OVERHEAD(I40E_RXBUFFER_2048))
+
+static inline int i40e_compute_pad(int rx_buf_len)
+{
+	int page_size, pad_size;
+
+	page_size = ALIGN(rx_buf_len, PAGE_SIZE / 2);
+	pad_size = SKB_WITH_OVERHEAD(page_size) - rx_buf_len;
+
+	return pad_size;
+}
+
+static inline int i40e_skb_pad(void)
+{
+	int rx_buf_len;
+
+	/* If a 2K buffer cannot handle a standard Ethernet frame then
+	 * optimize padding for a 3K buffer instead of a 1.5K buffer.
+	 *
+	 * For a 3K buffer we need to add enough padding to allow for
+	 * tailroom due to NET_IP_ALIGN possibly shifting us out of
+	 * cache-line alignment.
+	 */
+	if (I40E_2K_TOO_SMALL_WITH_PADDING)
+		rx_buf_len = I40E_RXBUFFER_3072 + SKB_DATA_ALIGN(NET_IP_ALIGN);
+	else
+		rx_buf_len = I40E_RXBUFFER_1536;
+
+	/* if needed make room for NET_IP_ALIGN */
+	rx_buf_len -= NET_IP_ALIGN;
+
+	return i40e_compute_pad(rx_buf_len);
+}
+
+#define I40E_SKB_PAD i40e_skb_pad()
+#else
+#define I40E_2K_TOO_SMALL_WITH_PADDING false
+#define I40E_SKB_PAD (NET_SKB_PAD + NET_IP_ALIGN)
+#endif
+
 /**
  * i40e_test_staterr - tests bits in Rx descriptor status and error fields
  * @rx_desc: pointer to receive descriptor (in le64 format)
@@ -341,7 +393,8 @@ struct i40e_ring {
 	u8 packet_stride;
 
 	u16 flags;
-#define I40E_TXR_FLAGS_WB_ON_ITR	BIT(0)
+#define I40E_TXR_FLAGS_WB_ON_ITR		BIT(0)
+#define I40E_RXR_FLAGS_BUILD_SKB_ENABLED	BIT(1)
 
 	/* stats structs */
 	struct i40e_queue_stats	stats;
@@ -369,6 +422,21 @@ struct i40e_ring {
 					 */
 } ____cacheline_internodealigned_in_smp;
 
+static inline bool ring_uses_build_skb(struct i40e_ring *ring)
+{
+	return !!(ring->flags & I40E_RXR_FLAGS_BUILD_SKB_ENABLED);
+}
+
+static inline void set_ring_build_skb_enabled(struct i40e_ring *ring)
+{
+	ring->flags |= I40E_RXR_FLAGS_BUILD_SKB_ENABLED;
+}
+
+static inline void clear_ring_build_skb_enabled(struct i40e_ring *ring)
+{
+	ring->flags &= ~I40E_RXR_FLAGS_BUILD_SKB_ENABLED;
+}
+
 enum i40e_latency_range {
 	I40E_LOWEST_LATENCY = 0,
 	I40E_LOW_LATENCY = 1,
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index 6b60c19..d96f10a 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -619,6 +619,17 @@ static inline void i40e_release_rx_desc(struct i40e_ring *rx_ring, u32 val)
 }
 
 /**
+ * i40e_rx_offset - Return expected offset into page to access data
+ * @rx_ring: Ring we are requesting offset of
+ *
+ * Returns the offset value for ring into the data buffer.
+ */
+static inline unsigned int i40e_rx_offset(struct i40e_ring *rx_ring)
+{
+	return ring_uses_build_skb(rx_ring) ? I40E_SKB_PAD : 0;
+}
+
+/**
  * i40e_alloc_mapped_page - recycle or make a new page
  * @rx_ring: ring to use
  * @bi: rx_buffer struct to modify
@@ -662,7 +673,7 @@ static bool i40e_alloc_mapped_page(struct i40e_ring *rx_ring,
 
 	bi->dma = dma;
 	bi->page = page;
-	bi->page_offset = 0;
+	bi->page_offset = i40e_rx_offset(rx_ring);
 
 	/* initialize pagecnt_bias to 1 representing we fully own page */
 	bi->pagecnt_bias = 1;
@@ -1057,7 +1068,7 @@ static void i40e_add_rx_frag(struct i40e_ring *rx_ring,
 #if (PAGE_SIZE < 8192)
 	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
 #else
-	unsigned int truesize = SKB_DATA_ALIGN(size);
+	unsigned int truesize =	SKB_DATA_ALIGN(size + i40e_rx_offset(rx_ring));
 #endif
 
 	skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, rx_buffer->page,
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
index dc82f65..901282c 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
@@ -122,6 +122,58 @@ enum i40e_dyn_idx_t {
 #define I40E_RX_DMA_ATTR \
 	(DMA_ATTR_SKIP_CPU_SYNC | DMA_ATTR_WEAK_ORDERING)
 
+/* Attempt to maximize the headroom available for incoming frames.  We
+ * use a 2K buffer for receives and need 1536/1534 to store the data for
+ * the frame.  This leaves us with 512 bytes of room.  From that we need
+ * to deduct the space needed for the shared info and the padding needed
+ * to IP align the frame.
+ *
+ * Note: For cache line sizes 256 or larger this value is going to end
+ *	 up negative.  In these cases we should fall back to the legacy
+ *	 receive path.
+ */
+#if (PAGE_SIZE < 8192)
+#define I40E_2K_TOO_SMALL_WITH_PADDING \
+((NET_SKB_PAD + I40E_RXBUFFER_1536) > SKB_WITH_OVERHEAD(I40E_RXBUFFER_2048))
+
+static inline int i40e_compute_pad(int rx_buf_len)
+{
+	int page_size, pad_size;
+
+	page_size = ALIGN(rx_buf_len, PAGE_SIZE / 2);
+	pad_size = SKB_WITH_OVERHEAD(page_size) - rx_buf_len;
+
+	return pad_size;
+}
+
+static inline int i40e_skb_pad(void)
+{
+	int rx_buf_len;
+
+	/* If a 2K buffer cannot handle a standard Ethernet frame then
+	 * optimize padding for a 3K buffer instead of a 1.5K buffer.
+	 *
+	 * For a 3K buffer we need to add enough padding to allow for
+	 * tailroom due to NET_IP_ALIGN possibly shifting us out of
+	 * cache-line alignment.
+	 */
+	if (I40E_2K_TOO_SMALL_WITH_PADDING)
+		rx_buf_len = I40E_RXBUFFER_3072 + SKB_DATA_ALIGN(NET_IP_ALIGN);
+	else
+		rx_buf_len = I40E_RXBUFFER_1536;
+
+	/* if needed make room for NET_IP_ALIGN */
+	rx_buf_len -= NET_IP_ALIGN;
+
+	return i40e_compute_pad(rx_buf_len);
+}
+
+#define I40E_SKB_PAD i40e_skb_pad()
+#else
+#define I40E_2K_TOO_SMALL_WITH_PADDING false
+#define I40E_SKB_PAD (NET_SKB_PAD + NET_IP_ALIGN)
+#endif
+
 /**
  * i40e_test_staterr - tests bits in Rx descriptor status and error fields
  * @rx_desc: pointer to receive descriptor (in le64 format)
@@ -328,7 +380,8 @@ struct i40e_ring {
 	u8 packet_stride;
 
 	u16 flags;
-#define I40E_TXR_FLAGS_WB_ON_ITR	BIT(0)
+#define I40E_TXR_FLAGS_WB_ON_ITR		BIT(0)
+#define I40E_RXR_FLAGS_BUILD_SKB_ENABLED	BIT(1)
 
 	/* stats structs */
 	struct i40e_queue_stats	stats;
@@ -356,6 +409,21 @@ struct i40e_ring {
 					 */
 } ____cacheline_internodealigned_in_smp;
 
+static inline bool ring_uses_build_skb(struct i40e_ring *ring)
+{
+	return !!(ring->flags & I40E_RXR_FLAGS_BUILD_SKB_ENABLED);
+}
+
+static inline void set_ring_build_skb_enabled(struct i40e_ring *ring)
+{
+	ring->flags |= I40E_RXR_FLAGS_BUILD_SKB_ENABLED;
+}
+
+static inline void clear_ring_build_skb_enabled(struct i40e_ring *ring)
+{
+	ring->flags &= ~I40E_RXR_FLAGS_BUILD_SKB_ENABLED;
+}
+
 enum i40e_latency_range {
 	I40E_LOWEST_LATENCY = 0,
 	I40E_LOW_LATENCY = 1,
diff --git a/drivers/net/ethernet/intel/i40evf/i40evf_main.c b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
index 95d5c04..e4136ce 100644
--- a/drivers/net/ethernet/intel/i40evf/i40evf_main.c
+++ b/drivers/net/ethernet/intel/i40evf/i40evf_main.c
@@ -704,7 +704,8 @@ static void i40evf_configure_rx(struct i40evf_adapter *adapter)
 		 * standard Ethernet mtu.  On x86 this gives us enough room
 		 * for shared info and 192 bytes of padding.
 		 */
-		if (netdev->mtu <= ETH_DATA_LEN)
+		if (!I40E_2K_TOO_SMALL_WITH_PADDING &&
+		    (netdev->mtu <= ETH_DATA_LEN))
 			rx_buf_len = I40E_RXBUFFER_1536 - NET_IP_ALIGN;
 	}
 #endif
@@ -712,6 +713,11 @@ static void i40evf_configure_rx(struct i40evf_adapter *adapter)
 	for (i = 0; i < adapter->num_active_queues; i++) {
 		adapter->rx_rings[i].tail = hw->hw_addr + I40E_QRX_TAIL1(i);
 		adapter->rx_rings[i].rx_buf_len = rx_buf_len;
+
+		if (adapter->flags & I40EVF_FLAG_LEGACY_RX)
+			clear_ring_build_skb_enabled(&adapter->rx_rings[i]);
+		else
+			set_ring_build_skb_enabled(&adapter->rx_rings[i]);
 	}
 }
 
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 10/11] i40e/i40evf: Add support for padding start of frames

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 10/11] i40e/i40evf: Add support for
> padding start of frames
> 
> From: Alexander Duyck <alexander.h.duyck@intel.com>
> 
> This patch adds padding to the start of frames to make room for headroom
> for us to eventually start using build_skb.  Right now we guarantee at least
> NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
> available.  For example on x86 the headroom should be 192 bytes.
> 
> On systems that have too large of a cache line size to support storing 1.5K
> padding and shared info we default to using 3K buffers and reserve
> everything that isn't used for skb_shared_info or the data buffer for
> headroom.
> 
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a
> ---
>  drivers/net/ethernet/intel/i40e/i40e_main.c     |  9 +++-
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c     | 15 +++++-
>  drivers/net/ethernet/intel/i40e/i40e_txrx.h     | 70
> ++++++++++++++++++++++++-
>  drivers/net/ethernet/intel/i40evf/i40e_txrx.c   | 15 +++++-
>  drivers/net/ethernet/intel/i40evf/i40e_txrx.h   | 70
> ++++++++++++++++++++++++-
>  drivers/net/ethernet/intel/i40evf/i40evf_main.c |  8 ++-
>  6 files changed, 179 insertions(+), 8 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 11/11] i40e/i40evf: Use build_skb to build frames

[Alice Michael]

From: Alexander Duyck <alexander.h.duyck@intel.com>

This patch is meant to improve the performance of the Rx path.
Specifically by using build_skb we have several distinct advantages.

In the case of small frames we were previously using a copy-break approach.
This means that we were allocating a page fragment to use for skb->head,
and were having to copy the packet into that region.  Both of those calls
are now avoided since we just build the skb around the data.

In the case of large frames the gains are much more significant.
Specifically we were having to allocate skb->head, and copy the headers as
before.  However in addition we were having to parse the header using
eth_get_headlen which could be quite expensive.  All of this is avoided by
building the frame around the data.  I have seen gains as high as 30% when
using VXLAN for instance due to just header pulling overhead.

Finally with all this in place it also sets us up to start looking at
enabling XDP.  Specifically we now have a path in which the data is in the
page and the frame is built around it.  So if we parse it with XDP before
we call build_skb we can take care of any necessary processing there.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Change-ID: Id4bdd618e94473d41f892417e5d8019639e421e3
---
 drivers/net/ethernet/intel/i40e/i40e_txrx.c   | 47 +++++++++++++++++++++++++++
 drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 47 +++++++++++++++++++++++++++
 2 files changed, 94 insertions(+)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
index 4b31aec..b4a7bfc 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c
@@ -1816,6 +1816,51 @@ static struct sk_buff *i40e_construct_skb(struct i40e_ring *rx_ring,
 }
 
 /**
+ * i40e_build_skb - Build skb around an existing buffer
+ * @rx_ring: rx descriptor ring to transact packets on
+ * @rx_buffer: rx buffer to pull data from
+ * @size: size of buffer to add to skb
+ *
+ * This function builds an skb around an existing Rx buffer, taking care
+ * to set up the skb correctly and avoid any memcpy overhead.
+ */
+static struct sk_buff *i40e_build_skb(struct i40e_ring *rx_ring,
+				      struct i40e_rx_buffer *rx_buffer,
+				      unsigned int size)
+{
+	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
+#if (PAGE_SIZE < 8192)
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
+#else
+	unsigned int truesize = SKB_DATA_ALIGN(size);
+#endif
+	struct sk_buff *skb;
+
+	/* prefetch first cache line of first page */
+	prefetch(va);
+#if L1_CACHE_BYTES < 128
+	prefetch(va + L1_CACHE_BYTES);
+#endif
+	/* build an skb around the page buffer */
+	skb = build_skb(va - I40E_SKB_PAD, truesize);
+	if (unlikely(!skb))
+		return NULL;
+
+	/* update pointers within the skb to store the data */
+	skb_reserve(skb, I40E_SKB_PAD);
+	__skb_put(skb, size);
+
+	/* buffer is used by skb, update page_offset */
+#if (PAGE_SIZE < 8192)
+	rx_buffer->page_offset ^= truesize;
+#else
+	rx_buffer->page_offset += truesize;
+#endif
+
+	return skb;
+}
+
+/**
  * i40e_put_rx_buffer - Clean up used buffer and either recycle or free
  * @rx_ring: rx descriptor ring to transact packets on
  * @rx_buffer: rx buffer to pull data from
@@ -1939,6 +1984,8 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
 		/* retrieve a buffer from the ring */
 		if (skb)
 			i40e_add_rx_frag(rx_ring, rx_buffer, skb, size);
+		else if (ring_uses_build_skb(rx_ring))
+			skb = i40e_build_skb(rx_ring, rx_buffer, size);
 		else
 			skb = i40e_construct_skb(rx_ring, rx_buffer, size);
 
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
index d96f10a..7f1341c 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c
@@ -1177,6 +1177,51 @@ static struct sk_buff *i40e_construct_skb(struct i40e_ring *rx_ring,
 }
 
 /**
+ * i40e_build_skb - Build skb around an existing buffer
+ * @rx_ring: rx descriptor ring to transact packets on
+ * @rx_buffer: rx buffer to pull data from
+ * @size: size of buffer to add to skb
+ *
+ * This function builds an skb around an existing Rx buffer, taking care
+ * to set up the skb correctly and avoid any memcpy overhead.
+ */
+static struct sk_buff *i40e_build_skb(struct i40e_ring *rx_ring,
+				      struct i40e_rx_buffer *rx_buffer,
+				      unsigned int size)
+{
+	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
+#if (PAGE_SIZE < 8192)
+	unsigned int truesize = i40e_rx_pg_size(rx_ring) / 2;
+#else
+	unsigned int truesize = SKB_DATA_ALIGN(size);
+#endif
+	struct sk_buff *skb;
+
+	/* prefetch first cache line of first page */
+	prefetch(va);
+#if L1_CACHE_BYTES < 128
+	prefetch(va + L1_CACHE_BYTES);
+#endif
+	/* build an skb around the page buffer */
+	skb = build_skb(va - I40E_SKB_PAD, truesize);
+	if (unlikely(!skb))
+		return NULL;
+
+	/* update pointers within the skb to store the data */
+	skb_reserve(skb, I40E_SKB_PAD);
+	__skb_put(skb, size);
+
+	/* buffer is used by skb, update page_offset */
+#if (PAGE_SIZE < 8192)
+	rx_buffer->page_offset ^= truesize;
+#else
+	rx_buffer->page_offset += truesize;
+#endif
+
+	return skb;
+}
+
+/**
  * i40e_put_rx_buffer - Clean up used buffer and either recycle or free
  * @rx_ring: rx descriptor ring to transact packets on
  * @rx_buffer: rx buffer to pull data from
@@ -1295,6 +1340,8 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
 		/* retrieve a buffer from the ring */
 		if (skb)
 			i40e_add_rx_frag(rx_ring, rx_buffer, skb, size);
+		else if (ring_uses_build_skb(rx_ring))
+			skb = i40e_build_skb(rx_ring, rx_buffer, size);
 		else
 			skb = i40e_construct_skb(rx_ring, rx_buffer, size);
 
-- 
2.9.3

[Intel-wired-lan] [next S66 v2 11/11] i40e/i40evf: Use build_skb to build frames

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 11/11] i40e/i40evf: Use build_skb to
> build frames
> 
> From: Alexander Duyck <alexander.h.duyck@intel.com>
> 
> This patch is meant to improve the performance of the Rx path.
> Specifically by using build_skb we have several distinct advantages.
> 
> In the case of small frames we were previously using a copy-break approach.
> This means that we were allocating a page fragment to use for skb->head,
> and were having to copy the packet into that region.  Both of those calls are
> now avoided since we just build the skb around the data.
> 
> In the case of large frames the gains are much more significant.
> Specifically we were having to allocate skb->head, and copy the headers as
> before.  However in addition we were having to parse the header using
> eth_get_headlen which could be quite expensive.  All of this is avoided by
> building the frame around the data.  I have seen gains as high as 30% when
> using VXLAN for instance due to just header pulling overhead.
> 
> Finally with all this in place it also sets us up to start looking at enabling XDP.
> Specifically we now have a path in which the data is in the page and the
> frame is built around it.  So if we parse it with XDP before we call build_skb
> we can take care of any necessary processing there.
> 
> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
> Change-ID: Id4bdd618e94473d41f892417e5d8019639e421e3
> ---
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c   | 47
> +++++++++++++++++++++++++++
>  drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 47
> +++++++++++++++++++++++++++
>  2 files changed, 94 insertions(+)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

[Intel-wired-lan] [next S66 v2 01/11] i40e: update error message when trying to add invalid filters

[Bowers, AndrewX]

> -----Original Message-----
> From: Intel-wired-lan [mailto:intel-wired-lan-bounces at lists.osuosl.org] On
> Behalf Of Alice Michael
> Sent: Wednesday, April 5, 2017 4:51 AM
> To: Michael, Alice <alice.michael@intel.com>; intel-wired-
> lan at lists.osuosl.org
> Subject: [Intel-wired-lan] [next S66 v2 01/11] i40e: update error message
> when trying to add invalid filters
> 
> From: Jacob Keller <jacob.e.keller@intel.com>
> 
> Re-word the error message displayed when adding a filter with an invalid
> flow type. Additionally, report a distinct error message when the IPv4
> protocol is at fault.
> 
> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
> Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
> ---
>  drivers/net/ethernet/intel/i40e/i40e_txrx.c | 9 +++++----
>  1 file changed, 5 insertions(+), 4 deletions(-)

Tested-by: Andrew Bowers <andrewx.bowers@intel.com>