[U-Boot] [PATCH v4 00/18] stm32f7: add sdram & gpio drivers

[U-Boot] [PATCH v4 00/18] stm32f7: add sdram & gpio drivers

[Vikas Manocha]

This patchset :
	- adds stm32 sdram driver based on DM
	- adds stm32 gpio driver based on DM
	- uses clock & pin control drivers to replace board specific
	  configurations from code
	- corrects sdram parameters as per correct sdram part
	- adds support for stm32f769 board

Changed in v4:
- rebased to master.

Changed in v3:
- made stm32_gpio_config() static.
- moved common.h inclusion before clk.h

Changed in v2:
- included files in correct order.
- moved the pinctrl specific routine from gpio driver to pinctrl
- used dev_get_addr() instead of fdtdec_get_addr_size_auto_parent() in
  gpio driver.
- pointed gpio name to bank name in device tree blob rather than copy.

Vikas Manocha (18):
  stm32f7: use clock driver to enable qspi controller clock
  stm32f7: sdram: move sdram driver code to ram drivers area
  stm32f7: dm: add driver model support for sdram
  ARM: DT: stm32f7: add sdram pin contol node
  stm32f7: use driver model for sdram initialization
  stm32f7: use clock driver to enable sdram controller clock
  stm32f7: sdram: use sdram device tree node to configure sdram
    controller
  dm: gpio: Add driver for stm32f7 gpio controller
  ARM: DT: stm32f7: add gpio device tree nodes
  stm32f7: use stm32f7 gpio driver supporting driver model
  stm32f746: to switch on user LED1 & read user button
  stm32f7: stm32f746-disco: read memory info from device tree
  stm32f7: enable board info read from device tree
  stm32f7: sdram: correct sdram configuration as per micron sdram
  stm32f7: increase the max no of pin configuration to 70
  stm32f7: move board specific pin muxing to dts
  stm32f7: add support for stm32f769 disco board
  stm32f7: remove not needed configuration from board config

 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/stm32f746-disco.dts              | 132 ++++++++++++
 arch/arm/dts/stm32f746.dtsi                   | 151 ++++++++++---
 arch/arm/dts/stm32f769-disco.dts              | 255 ++++++++++++++++++++++
 arch/arm/include/asm/arch-stm32f7/gpio.h      |  21 +-
 board/st/stm32f746-disco/stm32f746-disco.c    | 299 ++++++--------------------
 configs/stm32f746-disco_defconfig             |   6 +
 doc/device-tree-bindings/ram/st,stm32-fmc.txt |  51 +++++
 drivers/clk/clk_stm32f7.c                     |  39 ----
 drivers/gpio/Kconfig                          |   9 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/stm32f7_gpio.c                   | 135 ++++++++++++
 drivers/pinctrl/pinctrl_stm32.c               |  50 ++++-
 drivers/ram/Kconfig                           |   8 +
 drivers/ram/Makefile                          |   1 +
 drivers/ram/stm32_sdram.c                     | 179 +++++++++++++++
 drivers/spi/stm32_qspi.c                      |  16 +-
 include/configs/stm32f746-disco.h             |  11 +-
 include/dt-bindings/memory/stm32-sdram.h      |  37 ++++
 19 files changed, 1076 insertions(+), 328 deletions(-)
 create mode 100644 arch/arm/dts/stm32f769-disco.dts
 create mode 100644 doc/device-tree-bindings/ram/st,stm32-fmc.txt
 create mode 100644 drivers/gpio/stm32f7_gpio.c
 create mode 100644 drivers/ram/stm32_sdram.c
 create mode 100644 include/dt-bindings/memory/stm32-sdram.h

-- 
1.9.1

[U-Boot] [PATCH v4 01/18] stm32f7: use clock driver to enable qspi controller clock

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746.dtsi |  1 +
 drivers/spi/stm32_qspi.c    | 16 +++++++++++++++-
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index b2b0b5f..883f818 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -78,6 +78,7 @@
 			reg-names = "QuadSPI", "QuadSPI-memory";
 			interrupts = <92>;
 			spi-max-frequency = <108000000>;
+			clocks = <&rcc 0 65>;
 			status = "disabled";
 		};
 		usart1: serial at 40011000 {
diff --git a/drivers/spi/stm32_qspi.c b/drivers/spi/stm32_qspi.c
index 05358eb..f0434a4 100644
--- a/drivers/spi/stm32_qspi.c
+++ b/drivers/spi/stm32_qspi.c
@@ -17,6 +17,7 @@
 #include <errno.h>
 #include <asm/arch/stm32.h>
 #include <asm/arch/stm32_defs.h>
+#include <clk.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -457,7 +458,20 @@ static int stm32_qspi_probe(struct udevice *bus)
 
 	priv->max_hz = plat->max_hz;
 
-	clock_setup(QSPI_CLOCK_CFG);
+#ifdef CONFIG_CLK
+	int ret;
+	struct clk clk;
+	ret = clk_get_by_index(bus, 0, &clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&clk);
+
+	if (ret) {
+		dev_err(bus, "failed to enable clock\n");
+		return ret;
+	}
+#endif
 
 	setbits_le32(&priv->regs->cr, STM32_QSPI_CR_SSHIFT);
 
-- 
1.9.1

[U-Boot] [PATCH v4 02/18] stm32f7: sdram: move sdram driver code to ram drivers area

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 board/st/stm32f746-disco/stm32f746-disco.c | 113 +--------------------------
 configs/stm32f746-disco_defconfig          |   2 +
 drivers/ram/Kconfig                        |   8 ++
 drivers/ram/Makefile                       |   1 +
 drivers/ram/stm32_sdram.c                  | 119 +++++++++++++++++++++++++++++
 5 files changed, 131 insertions(+), 112 deletions(-)
 create mode 100644 drivers/ram/stm32_sdram.c

diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index fdad8d1..1569358 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -10,7 +10,6 @@
 #include <asm/armv7m.h>
 #include <asm/arch/stm32.h>
 #include <asm/arch/gpio.h>
-#include <asm/arch/fmc.h>
 #include <dm/platdata.h>
 #include <dm/platform_data/serial_stm32x7.h>
 #include <asm/arch/stm32_periph.h>
@@ -106,57 +105,8 @@ out:
 	return rv;
 }
 
-static inline u32 _ns2clk(u32 ns, u32 freq)
-{
-	u32 tmp = freq/1000000;
-	return (tmp * ns) / 1000;
-}
-
-#define NS2CLK(ns) (_ns2clk(ns, freq))
-
-/*
- * Following are timings for IS42S16400J, from corresponding datasheet
- */
-#define SDRAM_CAS	3	/* 3 cycles */
-#define SDRAM_NB	1	/* Number of banks */
-#define SDRAM_MWID	1	/* 16 bit memory */
-
-#define SDRAM_NR	0x1	/* 12-bit row */
-#define SDRAM_NC	0x0	/* 8-bit col */
-#define SDRAM_RBURST	0x1	/* Single read requests always as bursts */
-#define SDRAM_RPIPE	0x0	/* No HCLK clock cycle delay */
-
-#define SDRAM_TRRD	NS2CLK(12)
-#define SDRAM_TRCD	NS2CLK(18)
-#define SDRAM_TRP	NS2CLK(18)
-#define SDRAM_TRAS	NS2CLK(42)
-#define SDRAM_TRC	NS2CLK(60)
-#define SDRAM_TRFC	NS2CLK(60)
-#define SDRAM_TCDL	(1 - 1)
-#define SDRAM_TRDL	NS2CLK(12)
-#define SDRAM_TBDL	(1 - 1)
-#define SDRAM_TREF	(NS2CLK(64000000 / 8192) - 20)
-#define SDRAM_TCCD	(1 - 1)
-
-#define SDRAM_TXSR	SDRAM_TRFC	/* Row cycle time after precharge */
-#define SDRAM_TMRD	1		/* Page 10, Mode Register Set */
-
-
-/* Last data in to row precharge, need also comply ineq on page 1648 */
-#define SDRAM_TWR	max(\
-	(int)max((int)SDRAM_TRDL, (int)(SDRAM_TRAS - SDRAM_TRCD)), \
-	(int)(SDRAM_TRC - SDRAM_TRCD - SDRAM_TRP)\
-)
-
-
-#define SDRAM_MODE_BL_SHIFT	0
-#define SDRAM_MODE_CAS_SHIFT	4
-#define SDRAM_MODE_BL		0
-#define SDRAM_MODE_CAS		SDRAM_CAS
-
 int dram_init(void)
 {
-	u32 freq;
 	int rv;
 
 	rv = fmc_setup_gpio();
@@ -164,67 +114,7 @@ int dram_init(void)
 		return rv;
 
 	clock_setup(FMC_CLOCK_CFG);
-
-	/*
-	 * Get frequency for NS2CLK calculation.
-	 */
-	freq = clock_get(CLOCK_AHB) / CONFIG_SYS_RAM_FREQ_DIV;
-
-	writel(
-		CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT
-		| SDRAM_CAS << FMC_SDCR_CAS_SHIFT
-		| SDRAM_NB << FMC_SDCR_NB_SHIFT
-		| SDRAM_MWID << FMC_SDCR_MWID_SHIFT
-		| SDRAM_NR << FMC_SDCR_NR_SHIFT
-		| SDRAM_NC << FMC_SDCR_NC_SHIFT
-		| SDRAM_RPIPE << FMC_SDCR_RPIPE_SHIFT
-		| SDRAM_RBURST << FMC_SDCR_RBURST_SHIFT,
-		&STM32_SDRAM_FMC->sdcr1);
-
-	writel(
-		SDRAM_TRCD << FMC_SDTR_TRCD_SHIFT
-		| SDRAM_TRP << FMC_SDTR_TRP_SHIFT
-		| SDRAM_TWR << FMC_SDTR_TWR_SHIFT
-		| SDRAM_TRC << FMC_SDTR_TRC_SHIFT
-		| SDRAM_TRAS << FMC_SDTR_TRAS_SHIFT
-		| SDRAM_TXSR << FMC_SDTR_TXSR_SHIFT
-		| SDRAM_TMRD << FMC_SDTR_TMRD_SHIFT,
-		&STM32_SDRAM_FMC->sdtr1);
-
-	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_START_CLOCK,
-	       &STM32_SDRAM_FMC->sdcmr);
-
-	udelay(200);	/* 200 us delay, page 10, "Power-Up" */
-	FMC_BUSY_WAIT();
-
-	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_PRECHARGE,
-	       &STM32_SDRAM_FMC->sdcmr);
-
-	udelay(100);
-	FMC_BUSY_WAIT();
-
-	writel((FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_AUTOREFRESH
-		| 7 << FMC_SDCMR_NRFS_SHIFT), &STM32_SDRAM_FMC->sdcmr);
-
-	udelay(100);
-	FMC_BUSY_WAIT();
-
-	writel(FMC_SDCMR_BANK_1 | (SDRAM_MODE_BL << SDRAM_MODE_BL_SHIFT
-		| SDRAM_MODE_CAS << SDRAM_MODE_CAS_SHIFT)
-		<< FMC_SDCMR_MODE_REGISTER_SHIFT | FMC_SDCMR_MODE_WRITE_MODE,
-		&STM32_SDRAM_FMC->sdcmr);
-
-	udelay(100);
-
-	FMC_BUSY_WAIT();
-
-	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_NORMAL,
-	       &STM32_SDRAM_FMC->sdcmr);
-
-	FMC_BUSY_WAIT();
-
-	/* Refresh timer */
-	writel(SDRAM_TREF, &STM32_SDRAM_FMC->sdrtr);
+	stm32_sdram_init();
 
 	/*
 	 * Fill in global info with description of SRAM configuration
@@ -233,7 +123,6 @@ int dram_init(void)
 	gd->bd->bi_dram[0].size  = CONFIG_SYS_RAM_SIZE;
 
 	gd->ram_size = CONFIG_SYS_RAM_SIZE;
-
 	return rv;
 }
 
diff --git a/configs/stm32f746-disco_defconfig b/configs/stm32f746-disco_defconfig
index b5457c6..046041a 100644
--- a/configs/stm32f746-disco_defconfig
+++ b/configs/stm32f746-disco_defconfig
@@ -43,3 +43,5 @@ CONFIG_CLK=y
 CONFIG_PINCTRL=y
 # CONFIG_PINCTRL_FULL is not set
 CONFIG_PINCTRL_STM32=y
+CONFIG_RAM=y
+CONFIG_STM32_SDRAM=y
diff --git a/drivers/ram/Kconfig b/drivers/ram/Kconfig
index ff09f22..61afd7a 100644
--- a/drivers/ram/Kconfig
+++ b/drivers/ram/Kconfig
@@ -16,3 +16,11 @@ config SPL_RAM
 	  If this is acceptable and you have a need to use RAM drivers in
 	  SPL, enable this option. It might provide a cleaner interface to
 	  setting up RAM (e.g. SDRAM / DDR) within SPL.
+
+config STM32_SDRAM
+	bool "Enable STM32 SDRAM support"
+	depends on RAM
+	help
+	  STM32F7 family devices support flexible memory controller(FMC) to
+	  support external memories like sdram, psram & nand.
+	  This driver is for the sdram memory interface with the FMC.
diff --git a/drivers/ram/Makefile b/drivers/ram/Makefile
index 0e10249..ecb036d 100644
--- a/drivers/ram/Makefile
+++ b/drivers/ram/Makefile
@@ -6,3 +6,4 @@
 #
 obj-$(CONFIG_RAM) += ram-uclass.o
 obj-$(CONFIG_SANDBOX) += sandbox_ram.o
+obj-$(CONFIG_STM32_SDRAM) += stm32_sdram.o
diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
new file mode 100644
index 0000000..13f8964
--- /dev/null
+++ b/drivers/ram/stm32_sdram.c
@@ -0,0 +1,119 @@
+/*
+ * (C) Copyright 2017
+ * Vikas Manocha, <vikas.manocha@st.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/fmc.h>
+#include <asm/arch/stm32.h>
+
+static inline u32 _ns2clk(u32 ns, u32 freq)
+{
+	u32 tmp = freq/1000000;
+	return (tmp * ns) / 1000;
+}
+
+#define NS2CLK(ns) (_ns2clk(ns, freq))
+
+/*
+ * Following are timings for IS42S16400J, from corresponding datasheet
+ */
+#define SDRAM_CAS	3	/* 3 cycles */
+#define SDRAM_NB	1	/* Number of banks */
+#define SDRAM_MWID	1	/* 16 bit memory */
+
+#define SDRAM_NR	0x1	/* 12-bit row */
+#define SDRAM_NC	0x0	/* 8-bit col */
+#define SDRAM_RBURST	0x1	/* Single read requests always as bursts */
+#define SDRAM_RPIPE	0x0	/* No HCLK clock cycle delay */
+
+#define SDRAM_TRRD	NS2CLK(12)
+#define SDRAM_TRCD	NS2CLK(18)
+#define SDRAM_TRP	NS2CLK(18)
+#define SDRAM_TRAS	NS2CLK(42)
+#define SDRAM_TRC	NS2CLK(60)
+#define SDRAM_TRFC	NS2CLK(60)
+#define SDRAM_TCDL	(1 - 1)
+#define SDRAM_TRDL	NS2CLK(12)
+#define SDRAM_TBDL	(1 - 1)
+#define SDRAM_TREF	(NS2CLK(64000000 / 8192) - 20)
+#define SDRAM_TCCD	(1 - 1)
+
+#define SDRAM_TXSR	SDRAM_TRFC	/* Row cycle time after precharge */
+#define SDRAM_TMRD	1		/* Page 10, Mode Register Set */
+
+
+/* Last data in to row precharge, need also comply ineq on page 1648 */
+#define SDRAM_TWR	max(\
+		(int)max((int)SDRAM_TRDL, (int)(SDRAM_TRAS - SDRAM_TRCD)), \
+		(int)(SDRAM_TRC - SDRAM_TRCD - SDRAM_TRP)\
+		)
+
+
+#define SDRAM_MODE_BL_SHIFT	0
+#define SDRAM_MODE_CAS_SHIFT	4
+#define SDRAM_MODE_BL		0
+#define SDRAM_MODE_CAS		SDRAM_CAS
+
+int stm32_sdram_init(void)
+{
+	u32 freq;
+
+	/*
+	 * Get frequency for NS2CLK calculation.
+	 */
+	freq = clock_get(CLOCK_AHB) / CONFIG_SYS_RAM_FREQ_DIV;
+
+	writel(CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT
+			| SDRAM_CAS << FMC_SDCR_CAS_SHIFT
+			| SDRAM_NB << FMC_SDCR_NB_SHIFT
+			| SDRAM_MWID << FMC_SDCR_MWID_SHIFT
+			| SDRAM_NR << FMC_SDCR_NR_SHIFT
+			| SDRAM_NC << FMC_SDCR_NC_SHIFT
+			| SDRAM_RPIPE << FMC_SDCR_RPIPE_SHIFT
+			| SDRAM_RBURST << FMC_SDCR_RBURST_SHIFT,
+			&STM32_SDRAM_FMC->sdcr1);
+
+	writel(SDRAM_TRCD << FMC_SDTR_TRCD_SHIFT
+			| SDRAM_TRP << FMC_SDTR_TRP_SHIFT
+			| SDRAM_TWR << FMC_SDTR_TWR_SHIFT
+			| SDRAM_TRC << FMC_SDTR_TRC_SHIFT
+			| SDRAM_TRAS << FMC_SDTR_TRAS_SHIFT
+			| SDRAM_TXSR << FMC_SDTR_TXSR_SHIFT
+			| SDRAM_TMRD << FMC_SDTR_TMRD_SHIFT,
+			&STM32_SDRAM_FMC->sdtr1);
+
+	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_START_CLOCK,
+	       &STM32_SDRAM_FMC->sdcmr);
+	udelay(200);	/* 200 us delay, page 10, "Power-Up" */
+	FMC_BUSY_WAIT();
+
+	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_PRECHARGE,
+	       &STM32_SDRAM_FMC->sdcmr);
+	udelay(100);
+	FMC_BUSY_WAIT();
+
+	writel((FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_AUTOREFRESH
+		| 7 << FMC_SDCMR_NRFS_SHIFT), &STM32_SDRAM_FMC->sdcmr);
+	udelay(100);
+	FMC_BUSY_WAIT();
+
+	writel(FMC_SDCMR_BANK_1 | (SDRAM_MODE_BL << SDRAM_MODE_BL_SHIFT
+	       | SDRAM_MODE_CAS << SDRAM_MODE_CAS_SHIFT)
+	       << FMC_SDCMR_MODE_REGISTER_SHIFT | FMC_SDCMR_MODE_WRITE_MODE,
+	       &STM32_SDRAM_FMC->sdcmr);
+	udelay(100);
+	FMC_BUSY_WAIT();
+
+	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_NORMAL,
+	       &STM32_SDRAM_FMC->sdcmr);
+	FMC_BUSY_WAIT();
+
+	/* Refresh timer */
+	writel(SDRAM_TREF, &STM32_SDRAM_FMC->sdrtr);
+
+	return 0;
+}
-- 
1.9.1

[U-Boot] [PATCH v4 03/18] stm32f7: dm: add driver model support for sdram

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 drivers/ram/stm32_sdram.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
index 13f8964..67be61f 100644
--- a/drivers/ram/stm32_sdram.c
+++ b/drivers/ram/stm32_sdram.c
@@ -6,6 +6,8 @@
  */
 
 #include <common.h>
+#include <dm.h>
+#include <ram.h>
 #include <asm/io.h>
 #include <asm/arch/fmc.h>
 #include <asm/arch/stm32.h>
@@ -117,3 +119,32 @@ int stm32_sdram_init(void)
 
 	return 0;
 }
+
+static int stm32_fmc_probe(struct udevice *dev)
+{
+	stm32_sdram_init();
+	return 0;
+}
+
+static int stm32_fmc_get_info(struct udevice *dev, struct ram_info *info)
+{
+	info->size = CONFIG_SYS_RAM_SIZE;
+	return 0;
+}
+
+static struct ram_ops stm32_fmc_ops = {
+	.get_info = stm32_fmc_get_info,
+};
+
+static const struct udevice_id stm32_fmc_ids[] = {
+	{ .compatible = "st,stm32-fmc" },
+	{ }
+};
+
+U_BOOT_DRIVER(stm32_fmc) = {
+	.name = "stm32_fmc",
+	.id = UCLASS_RAM,
+	.of_match = stm32_fmc_ids,
+	.ops = &stm32_fmc_ops,
+	.probe = stm32_fmc_probe,
+};
-- 
1.9.1

[U-Boot] [PATCH v4 04/18] ARM: DT: stm32f7: add sdram pin contol node

[Vikas Manocha]

Also added DT binding doc for stm32 fmc(flexible memory controller).

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts              |  7 ++++
 arch/arm/dts/stm32f746.dtsi                   | 56 +++++++++++++++++++++++++++
 doc/device-tree-bindings/ram/st,stm32-fmc.txt | 51 ++++++++++++++++++++++++
 3 files changed, 114 insertions(+)
 create mode 100644 doc/device-tree-bindings/ram/st,stm32-fmc.txt

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index 07e0ca7..5846b0d 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -1,5 +1,6 @@
 /*
  * Copyright 2016 - Michael Kurz <michi.kurz@gmail.com>
+ * Copyright 2016 - Vikas MANOCHA <vikas.manocha@st.com>
  *
  * Based on:
  * stm32f469-disco.dts from Linux
@@ -76,6 +77,12 @@
 	status = "okay";
 };
 
+&fmc {
+	pinctrl-0 = <&fmc_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &mac {
 	status = "okay";
 	pinctrl-0 = <&ethernet_mii>;
diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index 883f818..3707550 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -1,5 +1,6 @@
 /*
  * Copyright 2016 - Michael Kurz <michi.kurz@gmail.com>
+ * Copyright 2016 - Vikas MANOCHA <vikas.manocha@st.com>
  *
  * Based on:
  * stm32f429.dtsi from Linux
@@ -70,6 +71,12 @@
 			status = "disabled";
 		};
 
+		fmc: fmc at A0000000 {
+			compatible = "st,stm32-fmc";
+			reg = <0xA0000000 0x1000>;
+			u-boot,dm-pre-reloc;
+		};
+
 		qspi: quadspi at A0001000 {
 			compatible = "st,stm32-qspi";
 			#address-cells = <1>;
@@ -143,6 +150,55 @@
 					slew-rate = <2>;
 				};
 			};
+
+			fmc_pins: fmc at 0 {
+				pins {
+					pinmux = <STM32F746_PD10_FUNC_FMC_D15>,
+						 <STM32F746_PD9_FUNC_FMC_D14>,
+						 <STM32F746_PD8_FUNC_FMC_D13>,
+						 <STM32F746_PE15_FUNC_FMC_D12>,
+						 <STM32F746_PE14_FUNC_FMC_D11>,
+						 <STM32F746_PE13_FUNC_FMC_D10>,
+						 <STM32F746_PE12_FUNC_FMC_D9>,
+						 <STM32F746_PE11_FUNC_FMC_D8>,
+						 <STM32F746_PE10_FUNC_FMC_D7>,
+						 <STM32F746_PE9_FUNC_FMC_D6>,
+						 <STM32F746_PE8_FUNC_FMC_D5>,
+						 <STM32F746_PE7_FUNC_FMC_D4>,
+						 <STM32F746_PD1_FUNC_FMC_D3>,
+						 <STM32F746_PD0_FUNC_FMC_D2>,
+						 <STM32F746_PD15_FUNC_FMC_D1>,
+						 <STM32F746_PD14_FUNC_FMC_D0>,
+
+						 <STM32F746_PE1_FUNC_FMC_NBL1>,
+						 <STM32F746_PE0_FUNC_FMC_NBL0>,
+
+						 <STM32F746_PG5_FUNC_FMC_A15_FMC_BA1>,
+						 <STM32F746_PG4_FUNC_FMC_A14_FMC_BA0>,
+
+						 <STM32F746_PG1_FUNC_FMC_A11>,
+						 <STM32F746_PG0_FUNC_FMC_A10>,
+						 <STM32F746_PF15_FUNC_FMC_A9>,
+						 <STM32F746_PF14_FUNC_FMC_A8>,
+						 <STM32F746_PF13_FUNC_FMC_A7>,
+						 <STM32F746_PF12_FUNC_FMC_A6>,
+						 <STM32F746_PF5_FUNC_FMC_A5>,
+						 <STM32F746_PF4_FUNC_FMC_A4>,
+						 <STM32F746_PF3_FUNC_FMC_A3>,
+						 <STM32F746_PF2_FUNC_FMC_A2>,
+						 <STM32F746_PF1_FUNC_FMC_A1>,
+						 <STM32F746_PF0_FUNC_FMC_A0>,
+
+						 <STM32F746_PH3_FUNC_FMC_SDNE0>,
+						 <STM32F746_PH5_FUNC_FMC_SDNWE>,
+						 <STM32F746_PF11_FUNC_FMC_SDNRAS>,
+						 <STM32F746_PG15_FUNC_FMC_SDNCAS>,
+						 <STM32F746_PC3_FUNC_FMC_SDCKE0>,
+						 <STM32F746_PG8_FUNC_FMC_SDCLK>;
+					slew-rate = <2>;
+				};
+			};
+
 		};
 	};
 };
diff --git a/doc/device-tree-bindings/ram/st,stm32-fmc.txt b/doc/device-tree-bindings/ram/st,stm32-fmc.txt
new file mode 100644
index 0000000..3d1392c
--- /dev/null
+++ b/doc/device-tree-bindings/ram/st,stm32-fmc.txt
@@ -0,0 +1,51 @@
+ST, stm32 flexible memory controller Drive
+Required properties:
+- compatible	: "st,stm32-fmc"
+- reg		: fmc controller base address
+- clocks	: fmc controller clock
+u-boot,dm-pre-reloc: flag to initialize memory before relocation.
+
+on-board sdram memory attributes:
+- st,sdram-control : parameters for sdram configuration, in this order:
+  number of columns
+  number of rows
+  memory width
+  number of intenal banks in memory
+  cas latency
+  read burst enable or disable
+  read pipe delay
+
+- st,sdram-timing: timings for sdram, in this order:
+  tmrd
+  txsr
+  tras
+  trc
+  trp
+  trcd
+
+There is device tree include file at :
+include/dt-bindings/memory/stm32-sdram.h to define sdram control and timing
+parameters as MACROS.
+
+Example:
+	fmc: fmc at A0000000 {
+	     compatible = "st,stm32-fmc";
+	     reg = <0xA0000000 0x1000>;
+	     clocks = <&rcc 0 64>;
+	     u-boot,dm-pre-reloc;
+	};
+
+	&fmc {
+		pinctrl-0 = <&fmc_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		mr-nbanks = <1>;
+		/* sdram memory configuration from sdram datasheet */
+	bank1: bank at 0 {
+	       st,sdram-control = /bits/ 8 <NO_COL_8 NO_ROW_12 MWIDTH_16 BANKS_2
+						CAS_3 RD_BURST_EN RD_PIPE_DL_0>;
+	       st,sdram-timing = /bits/ 8 <TMRD_1 TXSR_60 TRAS_42 TRC_60 TRP_18
+						TRCD_18>;
+       };
+}
-- 
1.9.1

[U-Boot] [PATCH v4 05/18] stm32f7: use driver model for sdram initialization

[Vikas Manocha]

As driver model takes care of pin control configuraion, this patch also
removes the sdram/fmc pin configuration.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 board/st/stm32f746-disco/stm32f746-disco.c | 89 +++++++-----------------------
 1 file changed, 19 insertions(+), 70 deletions(-)

diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index 1569358..e1113a6 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -6,6 +6,8 @@
  */
 
 #include <common.h>
+#include <dm.h>
+#include <ram.h>
 #include <asm/io.h>
 #include <asm/armv7m.h>
 #include <asm/arch/stm32.h>
@@ -26,66 +28,8 @@ const struct stm32_gpio_ctl gpio_ctl_gpout = {
 	.af = STM32_GPIO_AF0
 };
 
-const struct stm32_gpio_ctl gpio_ctl_fmc = {
-	.mode = STM32_GPIO_MODE_AF,
-	.otype = STM32_GPIO_OTYPE_PP,
-	.speed = STM32_GPIO_SPEED_100M,
-	.pupd = STM32_GPIO_PUPD_NO,
-	.af = STM32_GPIO_AF12
-};
-
-static const struct stm32_gpio_dsc ext_ram_fmc_gpio[] = {
-	/* Chip is LQFP144, see DM00077036.pdf for details */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_10},	/* 79, FMC_D15 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_9},	/* 78, FMC_D14 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_8},	/* 77, FMC_D13 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_15},	/* 68, FMC_D12 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_14},	/* 67, FMC_D11 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_13},	/* 66, FMC_D10 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_12},	/* 65, FMC_D9 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_11},	/* 64, FMC_D8 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_10},	/* 63, FMC_D7 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_9},	/* 60, FMC_D6 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_8},	/* 59, FMC_D5 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_7},	/* 58, FMC_D4 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_1},	/* 115, FMC_D3 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_0},	/* 114, FMC_D2 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_15},	/* 86, FMC_D1 */
-	{STM32_GPIO_PORT_D, STM32_GPIO_PIN_14},	/* 85, FMC_D0 */
-
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_1},	/* 142, FMC_NBL1 */
-	{STM32_GPIO_PORT_E, STM32_GPIO_PIN_0},	/* 141, FMC_NBL0 */
-
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_5},	/* 90, FMC_A15, BA1 */
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_4},	/* 89, FMC_A14, BA0 */
-
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_1},	/* 57, FMC_A11 */
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_0},	/* 56, FMC_A10 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_15},	/* 55, FMC_A9 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_14},	/* 54, FMC_A8 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_13},	/* 53, FMC_A7 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_12},	/* 50, FMC_A6 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_5},	/* 15, FMC_A5 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_4},	/* 14, FMC_A4 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_3},	/* 13, FMC_A3 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_2},	/* 12, FMC_A2 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_1},	/* 11, FMC_A1 */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_0},	/* 10, FMC_A0 */
-
-	{STM32_GPIO_PORT_H, STM32_GPIO_PIN_3},	/* 136, SDRAM_NE */
-	{STM32_GPIO_PORT_F, STM32_GPIO_PIN_11},	/* 49, SDRAM_NRAS */
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_15},	/* 132, SDRAM_NCAS */
-	{STM32_GPIO_PORT_H, STM32_GPIO_PIN_5},	/* 26, SDRAM_NWE */
-	{STM32_GPIO_PORT_C, STM32_GPIO_PIN_3},	/* 135, SDRAM_CKE */
-
-	{STM32_GPIO_PORT_G, STM32_GPIO_PIN_8},	/* 93, SDRAM_CLK */
-};
-
 static int fmc_setup_gpio(void)
 {
-	int rv = 0;
-	int i;
-
 	clock_setup(GPIO_B_CLOCK_CFG);
 	clock_setup(GPIO_C_CLOCK_CFG);
 	clock_setup(GPIO_D_CLOCK_CFG);
@@ -94,19 +38,13 @@ static int fmc_setup_gpio(void)
 	clock_setup(GPIO_G_CLOCK_CFG);
 	clock_setup(GPIO_H_CLOCK_CFG);
 
-	for (i = 0; i < ARRAY_SIZE(ext_ram_fmc_gpio); i++) {
-		rv = stm32_gpio_config(&ext_ram_fmc_gpio[i],
-				&gpio_ctl_fmc);
-		if (rv)
-			goto out;
-	}
-
-out:
-	return rv;
+	return 0;
 }
 
 int dram_init(void)
 {
+	struct udevice *dev;
+	struct ram_info ram;
 	int rv;
 
 	rv = fmc_setup_gpio();
@@ -114,15 +52,26 @@ int dram_init(void)
 		return rv;
 
 	clock_setup(FMC_CLOCK_CFG);
-	stm32_sdram_init();
+
+	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
+	if (rv) {
+		debug("DRAM init failed: %d\n", rv);
+		return rv;
+	}
+	rv = ram_get_info(dev, &ram);
+	if (rv) {
+		debug("Cannot get DRAM size: %d\n", rv);
+		return rv;
+	}
+	debug("SDRAM base=%lx, size=%x\n", ram.base, ram.size);
+	gd->ram_size = ram.size;
 
 	/*
 	 * Fill in global info with description of SRAM configuration
 	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_RAM_BASE;
-	gd->bd->bi_dram[0].size  = CONFIG_SYS_RAM_SIZE;
+	gd->bd->bi_dram[0].size  = ram.size;
 
-	gd->ram_size = CONFIG_SYS_RAM_SIZE;
 	return rv;
 }
 
-- 
1.9.1

[U-Boot] [PATCH v4 06/18] stm32f7: use clock driver to enable sdram controller clock

[Vikas Manocha]

This patch also removes the sdram/fmc clock enable from board specific
code.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746.dtsi                |  1 +
 board/st/stm32f746-disco/stm32f746-disco.c |  2 --
 drivers/ram/stm32_sdram.c                  | 15 +++++++++++++++
 3 files changed, 16 insertions(+), 2 deletions(-)

diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index 3707550..e9fd6f4 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -74,6 +74,7 @@
 		fmc: fmc at A0000000 {
 			compatible = "st,stm32-fmc";
 			reg = <0xA0000000 0x1000>;
+			clocks = <&rcc 0 64>;
 			u-boot,dm-pre-reloc;
 		};
 
diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index e1113a6..370db15 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -51,8 +51,6 @@ int dram_init(void)
 	if (rv)
 		return rv;
 
-	clock_setup(FMC_CLOCK_CFG);
-
 	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
 	if (rv) {
 		debug("DRAM init failed: %d\n", rv);
diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
index 67be61f..67d8855 100644
--- a/drivers/ram/stm32_sdram.c
+++ b/drivers/ram/stm32_sdram.c
@@ -6,6 +6,7 @@
  */
 
 #include <common.h>
+#include <clk.h>
 #include <dm.h>
 #include <ram.h>
 #include <asm/io.h>
@@ -122,6 +123,20 @@ int stm32_sdram_init(void)
 
 static int stm32_fmc_probe(struct udevice *dev)
 {
+#ifdef CONFIG_CLK
+	int ret;
+	struct clk clk;
+	ret = clk_get_by_index(dev, 0, &clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&clk);
+
+	if (ret) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+#endif
 	stm32_sdram_init();
 	return 0;
 }
-- 
1.9.1

[U-Boot] [PATCH v4 07/18] stm32f7: sdram: use sdram device tree node to configure sdram controller

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts         |  10 +++
 drivers/ram/stm32_sdram.c                | 144 +++++++++++++++++++------------
 include/dt-bindings/memory/stm32-sdram.h |  34 ++++++++
 3 files changed, 135 insertions(+), 53 deletions(-)
 create mode 100644 include/dt-bindings/memory/stm32-sdram.h

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index 5846b0d..f098d2e 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -47,6 +47,7 @@
 
 /dts-v1/;
 #include "stm32f746.dtsi"
+#include <dt-bindings/memory/stm32-sdram.h>
 
 / {
 	model = "STMicroelectronics STM32F746-DISCO board";
@@ -81,6 +82,15 @@
 	pinctrl-0 = <&fmc_pins>;
 	pinctrl-names = "default";
 	status = "okay";
+
+	mr-nbanks = <1>;
+	/* sdram memory configuration from sdram datasheet IS42S16400J */
+	bank1: bank at 0 {
+	       st,sdram-control = /bits/ 8 <NO_COL_8 NO_ROW_12 MWIDTH_16 BANKS_2
+	       				    CAS_3 RD_BURST_EN RD_PIPE_DL_0>;
+	       st,sdram-timing = /bits/ 8 <TMRD_1 TXSR_60 TRAS_42 TRC_60 TRP_18
+	       				   TRCD_18>;
+       };
 };
 
 &mac {
diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
index 67d8855..eb1ab94 100644
--- a/drivers/ram/stm32_sdram.c
+++ b/drivers/ram/stm32_sdram.c
@@ -13,6 +13,31 @@
 #include <asm/arch/fmc.h>
 #include <asm/arch/stm32.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
+struct stm32_sdram_control {
+	u8 no_columns;
+	u8 no_rows;
+	u8 memory_width;
+	u8 no_banks;
+	u8 cas_latency;
+	u8 rd_burst;
+	u8 rd_pipe_delay;
+};
+
+struct stm32_sdram_timing {
+	u8 tmrd;
+	u8 txsr;
+	u8 tras;
+	u8 trc;
+	u8 trp;
+	u8 trcd;
+};
+struct stm32_sdram_params {
+	u8 no_sdram_banks;
+	struct stm32_sdram_control sdram_control;
+	struct stm32_sdram_timing sdram_timing;
+};
 static inline u32 _ns2clk(u32 ns, u32 freq)
 {
 	u32 tmp = freq/1000000;
@@ -21,73 +46,53 @@ static inline u32 _ns2clk(u32 ns, u32 freq)
 
 #define NS2CLK(ns) (_ns2clk(ns, freq))
 
-/*
- * Following are timings for IS42S16400J, from corresponding datasheet
- */
-#define SDRAM_CAS	3	/* 3 cycles */
-#define SDRAM_NB	1	/* Number of banks */
-#define SDRAM_MWID	1	/* 16 bit memory */
-
-#define SDRAM_NR	0x1	/* 12-bit row */
-#define SDRAM_NC	0x0	/* 8-bit col */
-#define SDRAM_RBURST	0x1	/* Single read requests always as bursts */
-#define SDRAM_RPIPE	0x0	/* No HCLK clock cycle delay */
-
-#define SDRAM_TRRD	NS2CLK(12)
-#define SDRAM_TRCD	NS2CLK(18)
-#define SDRAM_TRP	NS2CLK(18)
-#define SDRAM_TRAS	NS2CLK(42)
-#define SDRAM_TRC	NS2CLK(60)
-#define SDRAM_TRFC	NS2CLK(60)
-#define SDRAM_TCDL	(1 - 1)
-#define SDRAM_TRDL	NS2CLK(12)
-#define SDRAM_TBDL	(1 - 1)
 #define SDRAM_TREF	(NS2CLK(64000000 / 8192) - 20)
-#define SDRAM_TCCD	(1 - 1)
-
-#define SDRAM_TXSR	SDRAM_TRFC	/* Row cycle time after precharge */
-#define SDRAM_TMRD	1		/* Page 10, Mode Register Set */
-
-
-/* Last data in to row precharge, need also comply ineq on page 1648 */
-#define SDRAM_TWR	max(\
-		(int)max((int)SDRAM_TRDL, (int)(SDRAM_TRAS - SDRAM_TRCD)), \
-		(int)(SDRAM_TRC - SDRAM_TRCD - SDRAM_TRP)\
-		)
-
 
 #define SDRAM_MODE_BL_SHIFT	0
 #define SDRAM_MODE_CAS_SHIFT	4
 #define SDRAM_MODE_BL		0
-#define SDRAM_MODE_CAS		SDRAM_CAS
+#define SDRAM_MODE_CAS		3
+
+#define SDRAM_TRDL	12
 
-int stm32_sdram_init(void)
+int stm32_sdram_init(struct udevice *dev)
 {
 	u32 freq;
+	u32 sdram_twr;
+	struct stm32_sdram_params *params = dev_get_platdata(dev);
 
 	/*
 	 * Get frequency for NS2CLK calculation.
 	 */
 	freq = clock_get(CLOCK_AHB) / CONFIG_SYS_RAM_FREQ_DIV;
+	debug("%s, sdram freq = %d\n", __func__, freq);
+
+	/* Last data in to row precharge, need also comply ineq on page 1648 */
+	sdram_twr = max(
+			max(SDRAM_TRDL, params->sdram_timing.tras
+			    - params->sdram_timing.trcd),
+			params->sdram_timing.trc - params->sdram_timing.trcd
+			- params->sdram_timing.trp
+		       );
 
 	writel(CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT
-			| SDRAM_CAS << FMC_SDCR_CAS_SHIFT
-			| SDRAM_NB << FMC_SDCR_NB_SHIFT
-			| SDRAM_MWID << FMC_SDCR_MWID_SHIFT
-			| SDRAM_NR << FMC_SDCR_NR_SHIFT
-			| SDRAM_NC << FMC_SDCR_NC_SHIFT
-			| SDRAM_RPIPE << FMC_SDCR_RPIPE_SHIFT
-			| SDRAM_RBURST << FMC_SDCR_RBURST_SHIFT,
-			&STM32_SDRAM_FMC->sdcr1);
-
-	writel(SDRAM_TRCD << FMC_SDTR_TRCD_SHIFT
-			| SDRAM_TRP << FMC_SDTR_TRP_SHIFT
-			| SDRAM_TWR << FMC_SDTR_TWR_SHIFT
-			| SDRAM_TRC << FMC_SDTR_TRC_SHIFT
-			| SDRAM_TRAS << FMC_SDTR_TRAS_SHIFT
-			| SDRAM_TXSR << FMC_SDTR_TXSR_SHIFT
-			| SDRAM_TMRD << FMC_SDTR_TMRD_SHIFT,
-			&STM32_SDRAM_FMC->sdtr1);
+		| params->sdram_control.cas_latency << FMC_SDCR_CAS_SHIFT
+		| params->sdram_control.no_banks << FMC_SDCR_NB_SHIFT
+		| params->sdram_control.memory_width << FMC_SDCR_MWID_SHIFT
+		| params->sdram_control.no_rows << FMC_SDCR_NR_SHIFT
+		| params->sdram_control.no_columns << FMC_SDCR_NC_SHIFT
+		| params->sdram_control.rd_pipe_delay << FMC_SDCR_RPIPE_SHIFT
+		| params->sdram_control.rd_burst << FMC_SDCR_RBURST_SHIFT,
+		&STM32_SDRAM_FMC->sdcr1);
+
+	writel(NS2CLK(params->sdram_timing.trcd) << FMC_SDTR_TRCD_SHIFT
+		| NS2CLK(params->sdram_timing.trp) << FMC_SDTR_TRP_SHIFT
+		| NS2CLK(sdram_twr) << FMC_SDTR_TWR_SHIFT
+		| NS2CLK(params->sdram_timing.trc) << FMC_SDTR_TRC_SHIFT
+		| NS2CLK(params->sdram_timing.tras) << FMC_SDTR_TRAS_SHIFT
+		| NS2CLK(params->sdram_timing.txsr) << FMC_SDTR_TXSR_SHIFT
+		| NS2CLK(params->sdram_timing.tmrd) << FMC_SDTR_TMRD_SHIFT,
+		&STM32_SDRAM_FMC->sdtr1);
 
 	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_START_CLOCK,
 	       &STM32_SDRAM_FMC->sdcmr);
@@ -121,11 +126,39 @@ int stm32_sdram_init(void)
 	return 0;
 }
 
+static int stm32_fmc_ofdata_to_platdata(struct udevice *dev)
+{
+	int ret;
+	int node = dev->of_offset;
+	const void *blob = gd->fdt_blob;
+	struct stm32_sdram_params *params = dev_get_platdata(dev);
+
+	params->no_sdram_banks = fdtdec_get_uint(blob, node, "mr-nbanks", 1);
+	debug("%s, no of banks = %d\n", __func__, params->no_sdram_banks);
+
+	fdt_for_each_subnode(node, blob, node) {
+		ret = fdtdec_get_byte_array(blob, node, "st,sdram-control",
+					    (u8 *)&params->sdram_control,
+					    sizeof(params->sdram_control));
+		if (ret)
+			return ret;
+
+		ret = fdtdec_get_byte_array(blob, node, "st,sdram-timing",
+					    (u8 *)&params->sdram_timing,
+					    sizeof(params->sdram_timing));
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
 static int stm32_fmc_probe(struct udevice *dev)
 {
 #ifdef CONFIG_CLK
 	int ret;
 	struct clk clk;
+
 	ret = clk_get_by_index(dev, 0, &clk);
 	if (ret < 0)
 		return ret;
@@ -137,7 +170,10 @@ static int stm32_fmc_probe(struct udevice *dev)
 		return ret;
 	}
 #endif
-	stm32_sdram_init();
+	ret = stm32_sdram_init(dev);
+	if (ret)
+		return ret;
+
 	return 0;
 }
 
@@ -161,5 +197,7 @@ U_BOOT_DRIVER(stm32_fmc) = {
 	.id = UCLASS_RAM,
 	.of_match = stm32_fmc_ids,
 	.ops = &stm32_fmc_ops,
+	.ofdata_to_platdata = stm32_fmc_ofdata_to_platdata,
 	.probe = stm32_fmc_probe,
+	.platdata_auto_alloc_size = sizeof(struct stm32_sdram_params),
 };
diff --git a/include/dt-bindings/memory/stm32-sdram.h b/include/dt-bindings/memory/stm32-sdram.h
new file mode 100644
index 0000000..4cd6c2b
--- /dev/null
+++ b/include/dt-bindings/memory/stm32-sdram.h
@@ -0,0 +1,34 @@
+#ifndef DT_BINDINGS_STM32_SDRAM_H
+#define DT_BINDINGS_STM32_SDRAM_H
+
+#define NO_COL_8	0x0
+#define NO_COL_9	0x1
+#define NO_COL_10	0x2
+#define NO_COL_11	0x3
+
+#define NO_ROW_11	0x0
+#define NO_ROW_12	0x1
+#define NO_ROW_13	0x2
+
+#define MWIDTH_8	0x0
+#define MWIDTH_16	0x1
+#define MWIDTH_32	0x2
+#define BANKS_2		0x0
+#define BANKS_4		0x1
+#define CAS_1		0x1
+#define CAS_2		0x2
+#define CAS_3		0x3
+#define RD_BURST_EN	0x1
+#define RD_BURST_DIS	0x0
+#define RD_PIPE_DL_0	0x0
+#define RD_PIPE_DL_1	0x1
+#define RD_PIPE_DL_2	0x2
+
+#define TMRD_1		0x1
+#define TXSR_60		60
+#define TRAS_42		42
+#define TRC_60		60
+#define TRP_18		18
+#define TRCD_18		18
+
+#endif
-- 
1.9.1

[U-Boot] [PATCH v4 08/18] dm: gpio: Add driver for stm32f7 gpio controller

[Vikas Manocha]

This patch adds gpio driver supporting driver model for stm32f7 gpio.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc: Christophe KERELLO <christophe.kerello@st.com>
---

Changed in v4:
- rebased to master.

Changed in v3:
- made stm32_gpio_config() static.
- moved common.h inclusion before clk.h

Changes in v2:
- included files in correct order.
- moved the pinctrl specific routine from gpio driver to pinctrl
- used dev_get_addr() instead of fdtdec_get_addr_size_auto_parent() in
  gpio driver.
- pointed gpio name to bank name in device tree blob rather than copy.

 arch/arm/include/asm/arch-stm32f7/gpio.h |  20 ++++-
 drivers/gpio/Kconfig                     |   9 +++
 drivers/gpio/Makefile                    |   1 +
 drivers/gpio/stm32f7_gpio.c              | 135 +++++++++++++++++++++++++++++++
 drivers/pinctrl/pinctrl_stm32.c          |  38 ++++++++-
 5 files changed, 198 insertions(+), 5 deletions(-)
 create mode 100644 drivers/gpio/stm32f7_gpio.c

diff --git a/arch/arm/include/asm/arch-stm32f7/gpio.h b/arch/arm/include/asm/arch-stm32f7/gpio.h
index 2942cd9..45999b4 100644
--- a/arch/arm/include/asm/arch-stm32f7/gpio.h
+++ b/arch/arm/include/asm/arch-stm32f7/gpio.h
@@ -96,6 +96,22 @@ struct stm32_gpio_ctl {
 	enum stm32_gpio_af	af;
 };
 
+struct stm32_gpio_regs {
+	u32 moder;	/* GPIO port mode */
+	u32 otyper;	/* GPIO port output type */
+	u32 ospeedr;	/* GPIO port output speed */
+	u32 pupdr;	/* GPIO port pull-up/pull-down */
+	u32 idr;	/* GPIO port input data */
+	u32 odr;	/* GPIO port output data */
+	u32 bsrr;	/* GPIO port bit set/reset */
+	u32 lckr;	/* GPIO port configuration lock */
+	u32 afr[2];	/* GPIO alternate function */
+};
+
+struct stm32_gpio_priv {
+	struct stm32_gpio_regs *regs;
+};
+
 static inline unsigned stm32_gpio_to_port(unsigned gpio)
 {
 	return gpio / 16;
@@ -106,8 +122,4 @@ static inline unsigned stm32_gpio_to_pin(unsigned gpio)
 	return gpio % 16;
 }
 
-int stm32_gpio_config(const struct stm32_gpio_dsc *gpio_dsc,
-		const struct stm32_gpio_ctl *gpio_ctl);
-int stm32_gpout_set(const struct stm32_gpio_dsc *gpio_dsc, int state);
-
 #endif /* _STM32_GPIO_H_ */
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index dc4108f..7c28e26 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -158,6 +158,15 @@ config PIC32_GPIO
 	help
 	  Say yes here to support Microchip PIC32 GPIOs.
 
+config STM32F7_GPIO
+	bool "ST STM32 GPIO driver"
+	depends on DM_GPIO
+	default y
+	help
+	  Device model driver support for STM32 GPIO controller. It should be
+	  usable on many stm32 families like stm32f4 & stm32H7.
+	  Tested on STM32F7.
+
 config MVEBU_GPIO
 	bool "Marvell MVEBU GPIO driver"
 	depends on DM_GPIO && ARCH_MVEBU
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 27f8068..0ca845f 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -49,6 +49,7 @@ oby-$(CONFIG_SX151X)		+= sx151x.o
 obj-$(CONFIG_SUNXI_GPIO)	+= sunxi_gpio.o
 obj-$(CONFIG_LPC32XX_GPIO)	+= lpc32xx_gpio.o
 obj-$(CONFIG_STM32_GPIO)	+= stm32_gpio.o
+obj-$(CONFIG_STM32F7_GPIO)	+= stm32f7_gpio.o
 obj-$(CONFIG_GPIO_UNIPHIER)	+= gpio-uniphier.o
 obj-$(CONFIG_ZYNQ_GPIO)		+= zynq_gpio.o
 obj-$(CONFIG_VYBRID_GPIO)	+= vybrid_gpio.o
diff --git a/drivers/gpio/stm32f7_gpio.c b/drivers/gpio/stm32f7_gpio.c
new file mode 100644
index 0000000..5e05463
--- /dev/null
+++ b/drivers/gpio/stm32f7_gpio.c
@@ -0,0 +1,135 @@
+/*
+ * (C) Copyright 2017
+ * Vikas Manocha, <vikas.manocha@st.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <fdtdec.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/stm32.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+
+#define MAX_SIZE_BANK_NAME		5
+#define STM32_GPIOS_PER_BANK		16
+#define MODE_BITS(gpio_pin)		(gpio_pin * 2)
+#define MODE_BITS_MASK			3
+#define IN_OUT_BIT_INDEX(gpio_pin)	(1UL << (gpio_pin))
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int stm32_gpio_direction_input(struct udevice *dev, unsigned offset)
+{
+	struct stm32_gpio_priv *priv = dev_get_priv(dev);
+	struct stm32_gpio_regs *regs = priv->regs;
+	int bits_index = MODE_BITS(offset);
+	int mask = MODE_BITS_MASK << bits_index;
+
+	clrsetbits_le32(&regs->moder, mask, STM32_GPIO_MODE_IN << bits_index);
+
+	return 0;
+}
+
+static int stm32_gpio_direction_output(struct udevice *dev, unsigned offset,
+				       int value)
+{
+	struct stm32_gpio_priv *priv = dev_get_priv(dev);
+	struct stm32_gpio_regs *regs = priv->regs;
+	int bits_index = MODE_BITS(offset);
+	int mask = MODE_BITS_MASK << bits_index;
+
+	clrsetbits_le32(&regs->moder, mask, STM32_GPIO_MODE_OUT << bits_index);
+	mask = IN_OUT_BIT_INDEX(offset);
+	clrsetbits_le32(&regs->odr, mask, value ? mask : 0);
+
+	return 0;
+}
+
+static int stm32_gpio_get_value(struct udevice *dev, unsigned offset)
+{
+	struct stm32_gpio_priv *priv = dev_get_priv(dev);
+	struct stm32_gpio_regs *regs = priv->regs;
+
+	return readl(&regs->idr) & IN_OUT_BIT_INDEX(offset) ? 1 : 0;
+}
+
+static int stm32_gpio_set_value(struct udevice *dev, unsigned offset, int value)
+{
+	struct stm32_gpio_priv *priv = dev_get_priv(dev);
+	struct stm32_gpio_regs *regs = priv->regs;
+	int mask = IN_OUT_BIT_INDEX(offset);
+
+	clrsetbits_le32(&regs->odr, mask, value ? mask : 0);
+
+	return 0;
+}
+
+static const struct dm_gpio_ops gpio_stm32_ops = {
+	.direction_input	= stm32_gpio_direction_input,
+	.direction_output	= stm32_gpio_direction_output,
+	.get_value		= stm32_gpio_get_value,
+	.set_value		= stm32_gpio_set_value,
+};
+
+static int gpio_stm32_probe(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+	struct stm32_gpio_priv *priv = dev_get_priv(dev);
+	fdt_addr_t addr;
+	char *name;
+
+	addr = dev_get_addr(dev);
+	if (addr == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	priv->regs = (struct stm32_gpio_regs *)addr;
+	name = (char *)fdtdec_locate_byte_array(gd->fdt_blob,
+						dev_of_offset(dev),
+						"st,bank-name",
+						MAX_SIZE_BANK_NAME);
+	if (!name)
+		return -EINVAL;
+	uc_priv->bank_name = name;
+	uc_priv->gpio_count = STM32_GPIOS_PER_BANK;
+	debug("%s, addr = 0x%p, bank_name = %s\n", __func__, (u32 *)priv->regs,
+	      uc_priv->bank_name);
+
+#ifdef CONFIG_CLK
+	struct clk clk;
+	int ret;
+	ret = clk_get_by_index(dev, 0, &clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&clk);
+
+	if (ret) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+	debug("clock enabled for device %s\n", dev->name);
+#endif
+
+	return 0;
+}
+
+static const struct udevice_id stm32_gpio_ids[] = {
+	{ .compatible = "st,stm32-gpio" },
+	{ }
+};
+
+U_BOOT_DRIVER(gpio_stm32) = {
+	.name	= "gpio_stm32",
+	.id	= UCLASS_GPIO,
+	.of_match = stm32_gpio_ids,
+	.probe	= gpio_stm32_probe,
+	.ops	= &gpio_stm32_ops,
+	.flags	= DM_FLAG_PRE_RELOC | DM_UC_FLAG_SEQ_ALIAS,
+	.priv_auto_alloc_size	= sizeof(struct stm32_gpio_priv),
+};
diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c
index aa2c440..0e74d05 100644
--- a/drivers/pinctrl/pinctrl_stm32.c
+++ b/drivers/pinctrl/pinctrl_stm32.c
@@ -1,10 +1,45 @@
 #include <common.h>
-#include <asm/arch/gpio.h>
 #include <dm.h>
 #include <dm/pinctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define MODE_BITS_MASK			3
+#define OSPEED_MASK			3
+#define PUPD_MASK			3
+#define OTYPE_MSK			1
+#define AFR_MASK			0xF
+
+static int stm32_gpio_config(struct gpio_desc *desc,
+			     const struct stm32_gpio_ctl *ctl)
+{
+	struct stm32_gpio_priv *priv = dev_get_priv(desc->dev);
+	struct stm32_gpio_regs *regs = priv->regs;
+	u32 index;
+
+	if (!ctl || ctl->af > 15 || ctl->mode > 3 || ctl->otype > 1 ||
+	    ctl->pupd > 2 || ctl->speed > 3)
+		return -EINVAL;
+
+	index = (desc->offset & 0x07) * 4;
+	clrsetbits_le32(&regs->afr[desc->offset >> 3], AFR_MASK << index,
+			ctl->af << index);
+
+	index = desc->offset * 2;
+	clrsetbits_le32(&regs->moder, MODE_BITS_MASK << index,
+			ctl->mode << index);
+	clrsetbits_le32(&regs->ospeedr, OSPEED_MASK << index,
+			ctl->speed << index);
+	clrsetbits_le32(&regs->pupdr, PUPD_MASK << index, ctl->pupd << index);
+
+	index = desc->offset;
+	clrsetbits_le32(&regs->otyper, OTYPE_MSK << index, ctl->otype << index);
+
+	return 0;
+}
 static int prep_gpio_dsc(struct stm32_gpio_dsc *gpio_dsc, u32 port_pin)
 {
 	gpio_dsc->port = (port_pin & 0xF000) >> 12;
@@ -18,6 +53,7 @@ static int prep_gpio_dsc(struct stm32_gpio_dsc *gpio_dsc, u32 port_pin)
 static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
 {
 	gpio_fn &= 0x00FF;
+	gpio_ctl->af = 0;
 
 	switch (gpio_fn) {
 	case 0:
-- 
1.9.1

[U-Boot] [PATCH v4 09/18] ARM: DT: stm32f7: add gpio device tree nodes

[Vikas Manocha]

Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts |  12 +++++
 arch/arm/dts/stm32f746.dtsi      | 111 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 123 insertions(+)

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index f098d2e..f830aa9 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -65,6 +65,18 @@
 	aliases {
 		serial0 = &usart1;
 		spi0 = &qspi;
+		/* Aliases for gpios so as to use sequence */
+		gpio0 = &gpioa;
+		gpio1 = &gpiob;
+		gpio2 = &gpioc;
+		gpio3 = &gpiod;
+		gpio4 = &gpioe;
+		gpio5 = &gpiof;
+		gpio6 = &gpiog;
+		gpio7 = &gpioh;
+		gpio8 = &gpioi;
+		gpio9 = &gpioj;
+		gpio10 = &gpiok;
 	};
 };
 
diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index e9fd6f4..865d5cf 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -114,6 +114,117 @@
 			u-boot,dm-pre-reloc;
 			pins-are-numbered;
 
+			gpioa: gpio at 40020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x0 0x400>;
+				clocks = <&rcc 0 0>;
+				st,bank-name = "GPIOA";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpiob: gpio at 40020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x400 0x400>;
+				clocks = <&rcc 0 1>;
+				st,bank-name = "GPIOB";
+				u-boot,dm-pre-reloc;
+			};
+
+
+			gpioc: gpio at 40020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x800 0x400>;
+				clocks = <&rcc 0 2>;
+				st,bank-name = "GPIOC";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpiod: gpio at 40020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0xc00 0x400>;
+				clocks = <&rcc 0 3>;
+				st,bank-name = "GPIOD";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpioe: gpio at 40021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x1000 0x400>;
+				clocks = <&rcc 0 4>;
+				st,bank-name = "GPIOE";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpiof: gpio at 40021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x1400 0x400>;
+				clocks = <&rcc 0 5>;
+				st,bank-name = "GPIOF";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpiog: gpio at 40021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x1800 0x400>;
+				clocks = <&rcc 0 6>;
+				st,bank-name = "GPIOG";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpioh: gpio at 40021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc 0 7>;
+				st,bank-name = "GPIOH";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpioi: gpio at 40022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x2000 0x400>;
+				clocks = <&rcc 0 8>;
+				st,bank-name = "GPIOI";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpioj: gpio at 40022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x2400 0x400>;
+				clocks = <&rcc 0 9>;
+				st,bank-name = "GPIOJ";
+				u-boot,dm-pre-reloc;
+			};
+
+			gpiok: gpio at 40022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				compatible = "st,stm32-gpio";
+				reg = <0x2800 0x400>;
+				clocks = <&rcc 0 10>;
+				st,bank-name = "GPIOK";
+				u-boot,dm-pre-reloc;
+			};
+
 			usart1_pins_a: usart1 at 0 {
 				pins1 {
 					pinmux = <STM32F746_PA9_FUNC_USART1_TX>;
-- 
1.9.1

[U-Boot] [PATCH v4 10/18] stm32f7: use stm32f7 gpio driver supporting driver model

[Vikas Manocha]

With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.

Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/include/asm/arch-stm32f7/gpio.h   |  1 +
 board/st/stm32f746-disco/stm32f746-disco.c | 70 ++----------------------------
 configs/stm32f746-disco_defconfig          |  4 ++
 drivers/clk/clk_stm32f7.c                  | 39 -----------------
 drivers/pinctrl/pinctrl_stm32.c            |  9 +++-
 include/configs/stm32f746-disco.h          |  1 -
 6 files changed, 15 insertions(+), 109 deletions(-)

diff --git a/arch/arm/include/asm/arch-stm32f7/gpio.h b/arch/arm/include/asm/arch-stm32f7/gpio.h
index 45999b4..56e469e 100644
--- a/arch/arm/include/asm/arch-stm32f7/gpio.h
+++ b/arch/arm/include/asm/arch-stm32f7/gpio.h
@@ -7,6 +7,7 @@
 
 #ifndef _STM32_GPIO_H_
 #define _STM32_GPIO_H_
+#include <asm/gpio.h>
 
 enum stm32_gpio_port {
 	STM32_GPIO_PORT_A = 0,
diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index 370db15..45a2c47 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -20,37 +20,12 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-const struct stm32_gpio_ctl gpio_ctl_gpout = {
-	.mode = STM32_GPIO_MODE_OUT,
-	.otype = STM32_GPIO_OTYPE_PP,
-	.speed = STM32_GPIO_SPEED_50M,
-	.pupd = STM32_GPIO_PUPD_NO,
-	.af = STM32_GPIO_AF0
-};
-
-static int fmc_setup_gpio(void)
-{
-	clock_setup(GPIO_B_CLOCK_CFG);
-	clock_setup(GPIO_C_CLOCK_CFG);
-	clock_setup(GPIO_D_CLOCK_CFG);
-	clock_setup(GPIO_E_CLOCK_CFG);
-	clock_setup(GPIO_F_CLOCK_CFG);
-	clock_setup(GPIO_G_CLOCK_CFG);
-	clock_setup(GPIO_H_CLOCK_CFG);
-
-	return 0;
-}
-
 int dram_init(void)
 {
 	struct udevice *dev;
 	struct ram_info ram;
 	int rv;
 
-	rv = fmc_setup_gpio();
-	if (rv)
-		return rv;
-
 	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
 	if (rv) {
 		debug("DRAM init failed: %d\n", rv);
@@ -73,37 +48,21 @@ int dram_init(void)
 	return rv;
 }
 
-int uart_setup_gpio(void)
-{
-	clock_setup(GPIO_A_CLOCK_CFG);
-	clock_setup(GPIO_B_CLOCK_CFG);
-	return 0;
-}
-
 #ifdef CONFIG_ETH_DESIGNWARE
-
 static int stmmac_setup(void)
 {
 	clock_setup(SYSCFG_CLOCK_CFG);
 	/* Set >RMII mode */
 	STM32_SYSCFG->pmc |= SYSCFG_PMC_MII_RMII_SEL;
-
-	clock_setup(GPIO_A_CLOCK_CFG);
-	clock_setup(GPIO_C_CLOCK_CFG);
-	clock_setup(GPIO_G_CLOCK_CFG);
 	clock_setup(STMMAC_CLOCK_CFG);
 
 	return 0;
 }
-#endif
 
-#ifdef CONFIG_STM32_QSPI
-
-static int qspi_setup(void)
+int board_early_init_f(void)
 {
-	clock_setup(GPIO_B_CLOCK_CFG);
-	clock_setup(GPIO_D_CLOCK_CFG);
-	clock_setup(GPIO_E_CLOCK_CFG);
+	stmmac_setup();
+
 	return 0;
 }
 #endif
@@ -113,29 +72,6 @@ u32 get_board_rev(void)
 	return 0;
 }
 
-int board_early_init_f(void)
-{
-	int res;
-
-	res = uart_setup_gpio();
-	if (res)
-		return res;
-
-#ifdef CONFIG_ETH_DESIGNWARE
-	res = stmmac_setup();
-	if (res)
-		return res;
-#endif
-
-#ifdef CONFIG_STM32_QSPI
-	res = qspi_setup();
-	if (res)
-		return res;
-#endif
-
-	return 0;
-}
-
 int board_init(void)
 {
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
diff --git a/configs/stm32f746-disco_defconfig b/configs/stm32f746-disco_defconfig
index 046041a..5e86a76 100644
--- a/configs/stm32f746-disco_defconfig
+++ b/configs/stm32f746-disco_defconfig
@@ -24,6 +24,7 @@ CONFIG_CMD_DNS=y
 CONFIG_CMD_LINK_LOCAL=y
 CONFIG_CMD_TIMER=y
 CONFIG_OF_CONTROL=y
+CONFIG_DM_SEQ_ALIAS=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETCONSOLE=y
 # CONFIG_MMC is not set
@@ -45,3 +46,6 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_STM32=y
 CONFIG_RAM=y
 CONFIG_STM32_SDRAM=y
+CONFIG_DM_GPIO=y
+CONFIG_STM32F7_GPIO=y
+CONFIG_SYS_MALLOC_F_LEN=0xC00
diff --git a/drivers/clk/clk_stm32f7.c b/drivers/clk/clk_stm32f7.c
index 0d86395..da3c204 100644
--- a/drivers/clk/clk_stm32f7.c
+++ b/drivers/clk/clk_stm32f7.c
@@ -228,56 +228,17 @@ static int stm32_clk_enable(struct clk *clk)
 void clock_setup(int peripheral)
 {
 	switch (peripheral) {
-	case GPIO_A_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_A_EN);
-		break;
-	case GPIO_B_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_B_EN);
-		break;
-	case GPIO_C_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_C_EN);
-		break;
-	case GPIO_D_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_D_EN);
-		break;
-	case GPIO_E_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_E_EN);
-		break;
-	case GPIO_F_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_F_EN);
-		break;
-	case GPIO_G_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_G_EN);
-		break;
-	case GPIO_H_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_H_EN);
-		break;
-	case GPIO_I_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_I_EN);
-		break;
-	case GPIO_J_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_J_EN);
-		break;
-	case GPIO_K_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
-		break;
 	case SYSCFG_CLOCK_CFG:
 		setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
 		break;
 	case TIMER2_CLOCK_CFG:
 		setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
 		break;
-	case FMC_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
-		break;
 	case STMMAC_CLOCK_CFG:
 		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_EN);
 		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
 		setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
 		break;
-	case QSPI_CLOCK_CFG:
-		setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
-		break;
 	default:
 		break;
 	}
diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c
index 0e74d05..01f0429 100644
--- a/drivers/pinctrl/pinctrl_stm32.c
+++ b/drivers/pinctrl/pinctrl_stm32.c
@@ -121,11 +121,16 @@ static int stm32_pinctrl_set_state_simple(struct udevice *dev,
 		if (len < 0)
 			return -EINVAL;
 		for (i = 0; i < len; i++) {
+			struct gpio_desc desc;
 			debug("%s: pinmux = %x\n", __func__, *(pin_mux + i));
 			prep_gpio_dsc(&gpio_dsc, *(pin_mux + i));
 			prep_gpio_ctl(&gpio_ctl, *(pin_mux + i), args.node);
-
-			rv = stm32_gpio_config(&gpio_dsc, &gpio_ctl);
+			rv = uclass_get_device_by_seq(UCLASS_GPIO,
+						      gpio_dsc.port, &desc.dev);
+			if (rv)
+				return rv;
+			desc.offset = gpio_dsc.pin;
+			rv = stm32_gpio_config(&desc, &gpio_ctl);
 			debug("%s: rv = %d\n\n", __func__, rv);
 			if (rv)
 				return rv;
diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index de3d661..e917ba9 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -30,7 +30,6 @@
 #define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_SIZE			(8 << 10)
 
-#define CONFIG_STM32_GPIO
 #define CONFIG_STM32_FLASH
 #define CONFIG_STM32X7_SERIAL
 
-- 
1.9.1

[U-Boot] [PATCH v4 11/18] stm32f746: to switch on user LED1 & read user button

[Vikas Manocha]

All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts           | 10 ++++++++
 board/st/stm32f746-disco/stm32f746-disco.c | 37 ++++++++++++++++++++++++++++++
 include/configs/stm32f746-disco.h          |  1 +
 3 files changed, 48 insertions(+)

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index f830aa9..8e4576b 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -78,6 +78,16 @@
 		gpio9 = &gpioj;
 		gpio10 = &gpiok;
 	};
+
+	led1 {
+		compatible = "st,led1";
+		led-gpio = <&gpioi 1 0>;
+	};
+
+	button1 {
+		compatible = "st,button1";
+		button-gpio = <&gpioi 11 0>;
+	};
 };
 
 &clk_hse {
diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index 45a2c47..52c1900 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -17,6 +17,7 @@
 #include <asm/arch/stm32_periph.h>
 #include <asm/arch/stm32_defs.h>
 #include <asm/arch/syscfg.h>
+#include <asm/gpio.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -72,6 +73,42 @@ u32 get_board_rev(void)
 	return 0;
 }
 
+int board_late_init(void)
+{
+	struct gpio_desc gpio = {};
+	int node;
+
+	node = fdt_node_offset_by_compatible(gd->fdt_blob, 0, "st,led1");
+	if (node < 0)
+		return -1;
+
+	gpio_request_by_name_nodev(gd->fdt_blob, node, "led-gpio", 0, &gpio,
+				   GPIOD_IS_OUT);
+
+	if (dm_gpio_is_valid(&gpio)) {
+		dm_gpio_set_value(&gpio, 0);
+		mdelay(10);
+		dm_gpio_set_value(&gpio, 1);
+	}
+
+	/* read button 1*/
+	node = fdt_node_offset_by_compatible(gd->fdt_blob, 0, "st,button1");
+	if (node < 0)
+		return -1;
+
+	gpio_request_by_name_nodev(gd->fdt_blob, node, "button-gpio", 0, &gpio,
+				   GPIOD_IS_IN);
+
+	if (dm_gpio_is_valid(&gpio)) {
+		if (dm_gpio_get_value(&gpio))
+			puts("usr button is at HIGH LEVEL\n");
+		else
+			puts("usr button is at LOW LEVEL\n");
+	}
+
+	return 0;
+}
+
 int board_init(void)
 {
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index e917ba9..48ac441 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -75,4 +75,5 @@
 
 #define CONFIG_CMD_MEM
 #define CONFIG_CMD_CACHE
+#define CONFIG_BOARD_LATE_INIT
 #endif /* __CONFIG_H */
-- 
1.9.1

[U-Boot] [PATCH v4 12/18] stm32f7: stm32f746-disco: read memory info from device tree

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4:
- Rebased to master as dram_init_banksize() prototype is changed.
Changed in v3: None
Changed in v2: None

 board/st/stm32f746-disco/stm32f746-disco.c | 42 +++++++++++++++++++++---------
 drivers/ram/stm32_sdram.c                  |  1 -
 include/configs/stm32f746-disco.h          |  6 +----
 3 files changed, 31 insertions(+), 18 deletions(-)

diff --git a/board/st/stm32f746-disco/stm32f746-disco.c b/board/st/stm32f746-disco/stm32f746-disco.c
index 52c1900..dc3a9dc 100644
--- a/board/st/stm32f746-disco/stm32f746-disco.c
+++ b/board/st/stm32f746-disco/stm32f746-disco.c
@@ -21,32 +21,51 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+int get_memory_base_size(fdt_addr_t *mr_base, fdt_addr_t *mr_size)
+{
+	int mr_node;
+
+	mr_node = fdt_path_offset(gd->fdt_blob, "/memory");
+	if (mr_node < 0)
+		return mr_node;
+	*mr_base = fdtdec_get_addr_size_auto_noparent(gd->fdt_blob, mr_node,
+						      "reg", 0, mr_size, false);
+	debug("mr_base = %lx, mr_size= %lx\n", *mr_base, *mr_size);
+
+	return 0;
+}
 int dram_init(void)
 {
 	struct udevice *dev;
-	struct ram_info ram;
 	int rv;
+	fdt_addr_t mr_base, mr_size;
 
 	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
 	if (rv) {
 		debug("DRAM init failed: %d\n", rv);
 		return rv;
 	}
-	rv = ram_get_info(dev, &ram);
-	if (rv) {
-		debug("Cannot get DRAM size: %d\n", rv);
+
+	rv = get_memory_base_size(&mr_base, &mr_size);
+	if (rv)
 		return rv;
-	}
-	debug("SDRAM base=%lx, size=%x\n", ram.base, ram.size);
-	gd->ram_size = ram.size;
+	gd->ram_size = mr_size;
+	gd->ram_top = mr_base;
 
+	return rv;
+}
+
+int dram_init_banksize(void)
+{
+	fdt_addr_t mr_base, mr_size;
+	get_memory_base_size(&mr_base, &mr_size);
 	/*
 	 * Fill in global info with description of SRAM configuration
 	 */
-	gd->bd->bi_dram[0].start = CONFIG_SYS_RAM_BASE;
-	gd->bd->bi_dram[0].size  = ram.size;
+	gd->bd->bi_dram[0].start = mr_base;
+	gd->bd->bi_dram[0].size  = mr_size;
 
-	return rv;
+	return 0;
 }
 
 #ifdef CONFIG_ETH_DESIGNWARE
@@ -111,7 +130,6 @@ int board_late_init(void)
 
 int board_init(void)
 {
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
+	gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
 	return 0;
 }
diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
index eb1ab94..5e09f35 100644
--- a/drivers/ram/stm32_sdram.c
+++ b/drivers/ram/stm32_sdram.c
@@ -179,7 +179,6 @@ static int stm32_fmc_probe(struct udevice *dev)
 
 static int stm32_fmc_get_info(struct udevice *dev, struct ram_info *info)
 {
-	info->size = CONFIG_SYS_RAM_SIZE;
 	return 0;
 }
 
diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index 48ac441..349ee3a 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -16,11 +16,7 @@
  * Configuration of the external SDRAM memory
  */
 #define CONFIG_NR_DRAM_BANKS		1
-#define CONFIG_SYS_RAM_SIZE		(8 * 1024 * 1024)
-#define CONFIG_SYS_RAM_CS		1
-#define CONFIG_SYS_RAM_FREQ_DIV		2
-#define CONFIG_SYS_RAM_BASE		0xC0000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_RAM_BASE
+#define CONFIG_SYS_RAM_FREQ_DIV         2
 #define CONFIG_SYS_LOAD_ADDR		0xC0400000
 #define CONFIG_LOADADDR			0xC0400000
 
-- 
1.9.1

[U-Boot] [PATCH v4 13/18] stm32f7: enable board info read from device tree

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 include/configs/stm32f746-disco.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index 349ee3a..73a316d 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -72,4 +72,5 @@
 #define CONFIG_CMD_MEM
 #define CONFIG_CMD_CACHE
 #define CONFIG_BOARD_LATE_INIT
+#define CONFIG_DISPLAY_BOARDINFO
 #endif /* __CONFIG_H */
-- 
1.9.1

[U-Boot] [PATCH v4 14/18] stm32f7: sdram: correct sdram configuration as per micron sdram

[Vikas Manocha]

Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.

Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts         | 13 +++++---
 drivers/ram/stm32_sdram.c                | 55 ++++++++++----------------------
 include/configs/stm32f746-disco.h        |  1 -
 include/dt-bindings/memory/stm32-sdram.h | 15 +++++----
 4 files changed, 33 insertions(+), 51 deletions(-)

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index 8e4576b..e720ff1 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -106,12 +106,15 @@
 	status = "okay";
 
 	mr-nbanks = <1>;
-	/* sdram memory configuration from sdram datasheet IS42S16400J */
+	/* Memory configuration from sdram datasheet MT48LC_4M32_B2B5-6A */
 	bank1: bank at 0 {
-	       st,sdram-control = /bits/ 8 <NO_COL_8 NO_ROW_12 MWIDTH_16 BANKS_2
-	       				    CAS_3 RD_BURST_EN RD_PIPE_DL_0>;
-	       st,sdram-timing = /bits/ 8 <TMRD_1 TXSR_60 TRAS_42 TRC_60 TRP_18
-	       				   TRCD_18>;
+	       st,sdram-control = /bits/ 8 <NO_COL_8 NO_ROW_12 MWIDTH_16 BANKS_4
+	       				    CAS_3 SDCLK_2 RD_BURST_EN
+					    RD_PIPE_DL_0>;
+	       st,sdram-timing = /bits/ 8 <TMRD_2 TXSR_6 TRAS_4 TRC_6 TWR_2
+	       				   TRP_2 TRCD_2>;
+		/* refcount = (64msec/total_row_sdram)*freq - 20 */
+	       st,sdram-refcount = < 1542 >;
        };
 };
 
diff --git a/drivers/ram/stm32_sdram.c b/drivers/ram/stm32_sdram.c
index 5e09f35..48b4979 100644
--- a/drivers/ram/stm32_sdram.c
+++ b/drivers/ram/stm32_sdram.c
@@ -21,6 +21,7 @@ struct stm32_sdram_control {
 	u8 memory_width;
 	u8 no_banks;
 	u8 cas_latency;
+	u8 sdclk;
 	u8 rd_burst;
 	u8 rd_pipe_delay;
 };
@@ -31,51 +32,25 @@ struct stm32_sdram_timing {
 	u8 tras;
 	u8 trc;
 	u8 trp;
+	u8 twr;
 	u8 trcd;
 };
 struct stm32_sdram_params {
 	u8 no_sdram_banks;
 	struct stm32_sdram_control sdram_control;
 	struct stm32_sdram_timing sdram_timing;
+	u32 sdram_ref_count;
 };
-static inline u32 _ns2clk(u32 ns, u32 freq)
-{
-	u32 tmp = freq/1000000;
-	return (tmp * ns) / 1000;
-}
-
-#define NS2CLK(ns) (_ns2clk(ns, freq))
-
-#define SDRAM_TREF	(NS2CLK(64000000 / 8192) - 20)
 
 #define SDRAM_MODE_BL_SHIFT	0
 #define SDRAM_MODE_CAS_SHIFT	4
 #define SDRAM_MODE_BL		0
-#define SDRAM_MODE_CAS		3
-
-#define SDRAM_TRDL	12
 
 int stm32_sdram_init(struct udevice *dev)
 {
-	u32 freq;
-	u32 sdram_twr;
 	struct stm32_sdram_params *params = dev_get_platdata(dev);
 
-	/*
-	 * Get frequency for NS2CLK calculation.
-	 */
-	freq = clock_get(CLOCK_AHB) / CONFIG_SYS_RAM_FREQ_DIV;
-	debug("%s, sdram freq = %d\n", __func__, freq);
-
-	/* Last data in to row precharge, need also comply ineq on page 1648 */
-	sdram_twr = max(
-			max(SDRAM_TRDL, params->sdram_timing.tras
-			    - params->sdram_timing.trcd),
-			params->sdram_timing.trc - params->sdram_timing.trcd
-			- params->sdram_timing.trp
-		       );
-
-	writel(CONFIG_SYS_RAM_FREQ_DIV << FMC_SDCR_SDCLK_SHIFT
+	writel(params->sdram_control.sdclk << FMC_SDCR_SDCLK_SHIFT
 		| params->sdram_control.cas_latency << FMC_SDCR_CAS_SHIFT
 		| params->sdram_control.no_banks << FMC_SDCR_NB_SHIFT
 		| params->sdram_control.memory_width << FMC_SDCR_MWID_SHIFT
@@ -85,13 +60,13 @@ int stm32_sdram_init(struct udevice *dev)
 		| params->sdram_control.rd_burst << FMC_SDCR_RBURST_SHIFT,
 		&STM32_SDRAM_FMC->sdcr1);
 
-	writel(NS2CLK(params->sdram_timing.trcd) << FMC_SDTR_TRCD_SHIFT
-		| NS2CLK(params->sdram_timing.trp) << FMC_SDTR_TRP_SHIFT
-		| NS2CLK(sdram_twr) << FMC_SDTR_TWR_SHIFT
-		| NS2CLK(params->sdram_timing.trc) << FMC_SDTR_TRC_SHIFT
-		| NS2CLK(params->sdram_timing.tras) << FMC_SDTR_TRAS_SHIFT
-		| NS2CLK(params->sdram_timing.txsr) << FMC_SDTR_TXSR_SHIFT
-		| NS2CLK(params->sdram_timing.tmrd) << FMC_SDTR_TMRD_SHIFT,
+	writel(params->sdram_timing.trcd << FMC_SDTR_TRCD_SHIFT
+		| params->sdram_timing.trp << FMC_SDTR_TRP_SHIFT
+		| params->sdram_timing.twr << FMC_SDTR_TWR_SHIFT
+		| params->sdram_timing.trc << FMC_SDTR_TRC_SHIFT
+		| params->sdram_timing.tras << FMC_SDTR_TRAS_SHIFT
+		| params->sdram_timing.txsr << FMC_SDTR_TXSR_SHIFT
+		| params->sdram_timing.tmrd << FMC_SDTR_TMRD_SHIFT,
 		&STM32_SDRAM_FMC->sdtr1);
 
 	writel(FMC_SDCMR_BANK_1 | FMC_SDCMR_MODE_START_CLOCK,
@@ -110,7 +85,7 @@ int stm32_sdram_init(struct udevice *dev)
 	FMC_BUSY_WAIT();
 
 	writel(FMC_SDCMR_BANK_1 | (SDRAM_MODE_BL << SDRAM_MODE_BL_SHIFT
-	       | SDRAM_MODE_CAS << SDRAM_MODE_CAS_SHIFT)
+	       | params->sdram_control.cas_latency << SDRAM_MODE_CAS_SHIFT)
 	       << FMC_SDCMR_MODE_REGISTER_SHIFT | FMC_SDCMR_MODE_WRITE_MODE,
 	       &STM32_SDRAM_FMC->sdcmr);
 	udelay(100);
@@ -121,7 +96,7 @@ int stm32_sdram_init(struct udevice *dev)
 	FMC_BUSY_WAIT();
 
 	/* Refresh timer */
-	writel(SDRAM_TREF, &STM32_SDRAM_FMC->sdrtr);
+	writel((params->sdram_ref_count) << 1, &STM32_SDRAM_FMC->sdrtr);
 
 	return 0;
 }
@@ -142,12 +117,14 @@ static int stm32_fmc_ofdata_to_platdata(struct udevice *dev)
 					    sizeof(params->sdram_control));
 		if (ret)
 			return ret;
-
 		ret = fdtdec_get_byte_array(blob, node, "st,sdram-timing",
 					    (u8 *)&params->sdram_timing,
 					    sizeof(params->sdram_timing));
 		if (ret)
 			return ret;
+
+		params->sdram_ref_count = fdtdec_get_int(blob, node,
+						"st,sdram-refcount", 8196);
 	}
 
 	return 0;
diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index 73a316d..cc0f8fd 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -16,7 +16,6 @@
  * Configuration of the external SDRAM memory
  */
 #define CONFIG_NR_DRAM_BANKS		1
-#define CONFIG_SYS_RAM_FREQ_DIV         2
 #define CONFIG_SYS_LOAD_ADDR		0xC0400000
 #define CONFIG_LOADADDR			0xC0400000
 
diff --git a/include/dt-bindings/memory/stm32-sdram.h b/include/dt-bindings/memory/stm32-sdram.h
index 4cd6c2b..89b719a 100644
--- a/include/dt-bindings/memory/stm32-sdram.h
+++ b/include/dt-bindings/memory/stm32-sdram.h
@@ -18,17 +18,20 @@
 #define CAS_1		0x1
 #define CAS_2		0x2
 #define CAS_3		0x3
+#define SDCLK_2		0x2
 #define RD_BURST_EN	0x1
 #define RD_BURST_DIS	0x0
 #define RD_PIPE_DL_0	0x0
 #define RD_PIPE_DL_1	0x1
 #define RD_PIPE_DL_2	0x2
 
-#define TMRD_1		0x1
-#define TXSR_60		60
-#define TRAS_42		42
-#define TRC_60		60
-#define TRP_18		18
-#define TRCD_18		18
+/* Timing = value +1 cycles */
+#define TMRD_2		(2 - 1)
+#define TXSR_6		(6 - 1)
+#define TRAS_4		(4 - 1)
+#define TRC_6		(6 - 1)
+#define TWR_2		(2 - 1)
+#define TRP_2		(2 - 1)
+#define TRCD_2		(2 - 1)
 
 #endif
-- 
1.9.1

[U-Boot] [PATCH v4 15/18] stm32f7: increase the max no of pin configuration to 70

[Vikas Manocha]

The number of pins to be configured could be more than 50 e.g. in case
of sdram controller, there are about 56 pins (32 data lines, 12 address
& some control signals).

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 drivers/pinctrl/pinctrl_stm32.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c
index 01f0429..d7b5ea3 100644
--- a/drivers/pinctrl/pinctrl_stm32.c
+++ b/drivers/pinctrl/pinctrl_stm32.c
@@ -7,6 +7,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define MAX_PINS_ONE_IP			70
 #define MODE_BITS_MASK			3
 #define OSPEED_MASK			3
 #define PUPD_MASK			3
@@ -95,7 +96,7 @@ static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
 static int stm32_pinctrl_set_state_simple(struct udevice *dev,
 					  struct udevice *periph)
 {
-	u32 pin_mux[50];
+	u32 pin_mux[MAX_PINS_ONE_IP];
 	struct fdtdec_phandle_args args;
 	int rv, len;
 
-- 
1.9.1

[U-Boot] [PATCH v4 16/18] stm32f7: move board specific pin muxing to dts

[Vikas Manocha]

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/stm32f746-disco.dts | 90 ++++++++++++++++++++++++++++++++++++++++
 arch/arm/dts/stm32f746.dtsi      | 86 --------------------------------------
 2 files changed, 90 insertions(+), 86 deletions(-)

diff --git a/arch/arm/dts/stm32f746-disco.dts b/arch/arm/dts/stm32f746-disco.dts
index e720ff1..2c7fa79 100644
--- a/arch/arm/dts/stm32f746-disco.dts
+++ b/arch/arm/dts/stm32f746-disco.dts
@@ -94,6 +94,96 @@
 	clock-frequency = <25000000>;
 };
 
+&pinctrl {
+	usart1_pins_a: usart1 at 0	{
+		pins1 {
+		       pinmux = <STM32F746_PA9_FUNC_USART1_TX>;
+				bias-disable;
+				drive-push-pull;
+				slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32F746_PB7_FUNC_USART1_RX>;
+			bias-disable;
+		};
+	};
+
+	ethernet_mii: mii at 0 {
+	      pins {
+		      pinmux = <STM32F746_PG13_FUNC_ETH_MII_TXD0_ETH_RMII_TXD0>,
+			     <STM32F746_PG14_FUNC_ETH_MII_TXD1_ETH_RMII_TXD1>,
+			     <STM32F746_PG11_FUNC_ETH_MII_TX_EN_ETH_RMII_TX_EN>,
+			     <STM32F746_PA2_FUNC_ETH_MDIO>,
+			     <STM32F746_PC1_FUNC_ETH_MDC>,
+			     <STM32F746_PA1_FUNC_ETH_MII_RX_CLK_ETH_RMII_REF_CLK>,
+			     <STM32F746_PA7_FUNC_ETH_MII_RX_DV_ETH_RMII_CRS_DV>,
+			     <STM32F746_PC4_FUNC_ETH_MII_RXD0_ETH_RMII_RXD0>,
+			     <STM32F746_PC5_FUNC_ETH_MII_RXD1_ETH_RMII_RXD1>;
+		      slew-rate = <2>;
+	      };
+	};
+
+	qspi_pins: qspi at 0 {
+		pins {
+			pinmux = <STM32F746_PB2_FUNC_QUADSPI_CLK>,
+			       <STM32F746_PB6_FUNC_QUADSPI_BK1_NCS>,
+			       <STM32F746_PD11_FUNC_QUADSPI_BK1_IO0>,
+			       <STM32F746_PD12_FUNC_QUADSPI_BK1_IO1>,
+			       <STM32F746_PD13_FUNC_QUADSPI_BK1_IO3>,
+			       <STM32F746_PE2_FUNC_QUADSPI_BK1_IO2>;
+			slew-rate = <2>;
+		};
+	};
+
+	fmc_pins: fmc at 0 {
+		pins {
+			pinmux = <STM32F746_PD10_FUNC_FMC_D15>,
+				 <STM32F746_PD9_FUNC_FMC_D14>,
+				 <STM32F746_PD8_FUNC_FMC_D13>,
+				 <STM32F746_PE15_FUNC_FMC_D12>,
+				 <STM32F746_PE14_FUNC_FMC_D11>,
+				 <STM32F746_PE13_FUNC_FMC_D10>,
+				 <STM32F746_PE12_FUNC_FMC_D9>,
+				 <STM32F746_PE11_FUNC_FMC_D8>,
+				 <STM32F746_PE10_FUNC_FMC_D7>,
+				 <STM32F746_PE9_FUNC_FMC_D6>,
+				 <STM32F746_PE8_FUNC_FMC_D5>,
+				 <STM32F746_PE7_FUNC_FMC_D4>,
+				 <STM32F746_PD1_FUNC_FMC_D3>,
+				 <STM32F746_PD0_FUNC_FMC_D2>,
+				 <STM32F746_PD15_FUNC_FMC_D1>,
+				 <STM32F746_PD14_FUNC_FMC_D0>,
+
+				 <STM32F746_PE1_FUNC_FMC_NBL1>,
+				 <STM32F746_PE0_FUNC_FMC_NBL0>,
+
+				 <STM32F746_PG5_FUNC_FMC_A15_FMC_BA1>,
+				 <STM32F746_PG4_FUNC_FMC_A14_FMC_BA0>,
+
+				 <STM32F746_PG1_FUNC_FMC_A11>,
+				 <STM32F746_PG0_FUNC_FMC_A10>,
+				 <STM32F746_PF15_FUNC_FMC_A9>,
+				 <STM32F746_PF14_FUNC_FMC_A8>,
+				 <STM32F746_PF13_FUNC_FMC_A7>,
+				 <STM32F746_PF12_FUNC_FMC_A6>,
+				 <STM32F746_PF5_FUNC_FMC_A5>,
+				 <STM32F746_PF4_FUNC_FMC_A4>,
+				 <STM32F746_PF3_FUNC_FMC_A3>,
+				 <STM32F746_PF2_FUNC_FMC_A2>,
+				 <STM32F746_PF1_FUNC_FMC_A1>,
+				 <STM32F746_PF0_FUNC_FMC_A0>,
+
+				 <STM32F746_PH3_FUNC_FMC_SDNE0>,
+				 <STM32F746_PH5_FUNC_FMC_SDNWE>,
+				 <STM32F746_PF11_FUNC_FMC_SDNRAS>,
+				 <STM32F746_PG15_FUNC_FMC_SDNCAS>,
+				 <STM32F746_PC3_FUNC_FMC_SDCKE0>,
+				 <STM32F746_PG8_FUNC_FMC_SDCLK>;
+			  slew-rate = <2>;
+		};
+	};
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/dts/stm32f746.dtsi b/arch/arm/dts/stm32f746.dtsi
index 865d5cf..ac24d98 100644
--- a/arch/arm/dts/stm32f746.dtsi
+++ b/arch/arm/dts/stm32f746.dtsi
@@ -225,92 +225,6 @@
 				u-boot,dm-pre-reloc;
 			};
 
-			usart1_pins_a: usart1 at 0 {
-				pins1 {
-					pinmux = <STM32F746_PA9_FUNC_USART1_TX>;
-					bias-disable;
-					drive-push-pull;
-					slew-rate = <2>;
-				};
-				pins2 {
-					pinmux = <STM32F746_PB7_FUNC_USART1_RX>;
-					bias-disable;
-				};
-			};
-			ethernet_mii: mii at 0 {
-				pins {
-					pinmux = <STM32F746_PG13_FUNC_ETH_MII_TXD0_ETH_RMII_TXD0>,
-						 <STM32F746_PG14_FUNC_ETH_MII_TXD1_ETH_RMII_TXD1>,
-						 <STM32F746_PG11_FUNC_ETH_MII_TX_EN_ETH_RMII_TX_EN>,
-						 <STM32F746_PA2_FUNC_ETH_MDIO>,
-						 <STM32F746_PC1_FUNC_ETH_MDC>,
-						 <STM32F746_PA1_FUNC_ETH_MII_RX_CLK_ETH_RMII_REF_CLK>,
-						 <STM32F746_PA7_FUNC_ETH_MII_RX_DV_ETH_RMII_CRS_DV>,
-						 <STM32F746_PC4_FUNC_ETH_MII_RXD0_ETH_RMII_RXD0>,
-						 <STM32F746_PC5_FUNC_ETH_MII_RXD1_ETH_RMII_RXD1>;
-					slew-rate = <2>;
-				};
-			};
-			qspi_pins: qspi at 0{
-				pins {
-					pinmux = <STM32F746_PB2_FUNC_QUADSPI_CLK>,
-						 <STM32F746_PB6_FUNC_QUADSPI_BK1_NCS>,
-						 <STM32F746_PD11_FUNC_QUADSPI_BK1_IO0>,
-						 <STM32F746_PD12_FUNC_QUADSPI_BK1_IO1>,
-						 <STM32F746_PD13_FUNC_QUADSPI_BK1_IO3>,
-						 <STM32F746_PE2_FUNC_QUADSPI_BK1_IO2>;
-					slew-rate = <2>;
-				};
-			};
-
-			fmc_pins: fmc at 0 {
-				pins {
-					pinmux = <STM32F746_PD10_FUNC_FMC_D15>,
-						 <STM32F746_PD9_FUNC_FMC_D14>,
-						 <STM32F746_PD8_FUNC_FMC_D13>,
-						 <STM32F746_PE15_FUNC_FMC_D12>,
-						 <STM32F746_PE14_FUNC_FMC_D11>,
-						 <STM32F746_PE13_FUNC_FMC_D10>,
-						 <STM32F746_PE12_FUNC_FMC_D9>,
-						 <STM32F746_PE11_FUNC_FMC_D8>,
-						 <STM32F746_PE10_FUNC_FMC_D7>,
-						 <STM32F746_PE9_FUNC_FMC_D6>,
-						 <STM32F746_PE8_FUNC_FMC_D5>,
-						 <STM32F746_PE7_FUNC_FMC_D4>,
-						 <STM32F746_PD1_FUNC_FMC_D3>,
-						 <STM32F746_PD0_FUNC_FMC_D2>,
-						 <STM32F746_PD15_FUNC_FMC_D1>,
-						 <STM32F746_PD14_FUNC_FMC_D0>,
-
-						 <STM32F746_PE1_FUNC_FMC_NBL1>,
-						 <STM32F746_PE0_FUNC_FMC_NBL0>,
-
-						 <STM32F746_PG5_FUNC_FMC_A15_FMC_BA1>,
-						 <STM32F746_PG4_FUNC_FMC_A14_FMC_BA0>,
-
-						 <STM32F746_PG1_FUNC_FMC_A11>,
-						 <STM32F746_PG0_FUNC_FMC_A10>,
-						 <STM32F746_PF15_FUNC_FMC_A9>,
-						 <STM32F746_PF14_FUNC_FMC_A8>,
-						 <STM32F746_PF13_FUNC_FMC_A7>,
-						 <STM32F746_PF12_FUNC_FMC_A6>,
-						 <STM32F746_PF5_FUNC_FMC_A5>,
-						 <STM32F746_PF4_FUNC_FMC_A4>,
-						 <STM32F746_PF3_FUNC_FMC_A3>,
-						 <STM32F746_PF2_FUNC_FMC_A2>,
-						 <STM32F746_PF1_FUNC_FMC_A1>,
-						 <STM32F746_PF0_FUNC_FMC_A0>,
-
-						 <STM32F746_PH3_FUNC_FMC_SDNE0>,
-						 <STM32F746_PH5_FUNC_FMC_SDNWE>,
-						 <STM32F746_PF11_FUNC_FMC_SDNRAS>,
-						 <STM32F746_PG15_FUNC_FMC_SDNCAS>,
-						 <STM32F746_PC3_FUNC_FMC_SDCKE0>,
-						 <STM32F746_PG8_FUNC_FMC_SDCLK>;
-					slew-rate = <2>;
-				};
-			};
-
 		};
 	};
 };
-- 
1.9.1

[U-Boot] [PATCH v4 17/18] stm32f7: add support for stm32f769 disco board

[Vikas Manocha]

This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.

To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 arch/arm/dts/Makefile            |   3 +-
 arch/arm/dts/stm32f769-disco.dts | 255 +++++++++++++++++++++++++++++++++++++++
 2 files changed, 257 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/stm32f769-disco.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index a2c0717..4456ced 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -184,7 +184,8 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 
 dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb
 
-dtb-$(CONFIG_STM32F7) += stm32f746-disco.dtb
+dtb-$(CONFIG_STM32F7) += stm32f746-disco.dtb \
+	stm32f769-disco.dtb
 
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
diff --git a/arch/arm/dts/stm32f769-disco.dts b/arch/arm/dts/stm32f769-disco.dts
new file mode 100644
index 0000000..6591cc8
--- /dev/null
+++ b/arch/arm/dts/stm32f769-disco.dts
@@ -0,0 +1,255 @@
+/*
+ * Copyright 2016 - Vikas Manocha <vikas.manocha@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f746.dtsi"
+#include <dt-bindings/memory/stm32-sdram.h>
+
+/ {
+	model = "STMicroelectronics STM32F769-DISCO board";
+	compatible = "st,stm32f769-disco", "st,stm32f7";
+
+	chosen {
+		bootargs = "root=/dev/ram rdinit=/linuxrc";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0xC0000000 0x1000000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+		spi0 = &qspi;
+		/* Aliases for gpios so as to use sequence */
+		gpio0 = &gpioa;
+		gpio1 = &gpiob;
+		gpio2 = &gpioc;
+		gpio3 = &gpiod;
+		gpio4 = &gpioe;
+		gpio5 = &gpiof;
+		gpio6 = &gpiog;
+		gpio7 = &gpioh;
+		gpio8 = &gpioi;
+		gpio9 = &gpioj;
+		gpio10 = &gpiok;
+	};
+
+	led1 {
+		compatible = "st,led1";
+		led-gpio = <&gpioj 5 0>;
+	};
+
+	button1 {
+		compatible = "st,button1";
+		button-gpio = <&gpioa 0 0>;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&pinctrl {
+	usart1_pins_a: usart1 at 0	{
+		pins1 {
+		       pinmux = <STM32F746_PA9_FUNC_USART1_TX>;
+				bias-disable;
+				drive-push-pull;
+				slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32F746_PA10_FUNC_USART1_RX>;
+			bias-disable;
+		};
+	};
+
+	ethernet_mii: mii at 0 {
+	      pins {
+		      pinmux = <STM32F746_PG13_FUNC_ETH_MII_TXD0_ETH_RMII_TXD0>,
+			     <STM32F746_PG14_FUNC_ETH_MII_TXD1_ETH_RMII_TXD1>,
+			     <STM32F746_PG11_FUNC_ETH_MII_TX_EN_ETH_RMII_TX_EN>,
+			     <STM32F746_PA2_FUNC_ETH_MDIO>,
+			     <STM32F746_PC1_FUNC_ETH_MDC>,
+			     <STM32F746_PA1_FUNC_ETH_MII_RX_CLK_ETH_RMII_REF_CLK>,
+			     <STM32F746_PA7_FUNC_ETH_MII_RX_DV_ETH_RMII_CRS_DV>,
+			     <STM32F746_PC4_FUNC_ETH_MII_RXD0_ETH_RMII_RXD0>,
+			     <STM32F746_PC5_FUNC_ETH_MII_RXD1_ETH_RMII_RXD1>;
+		      slew-rate = <2>;
+	      };
+	};
+
+	qspi_pins: qspi at 0 {
+		pins {
+			pinmux = <STM32F746_PB2_FUNC_QUADSPI_CLK>,
+			       <STM32F746_PB6_FUNC_QUADSPI_BK1_NCS>,
+			       <STM32F746_PC9_FUNC_QUADSPI_BK1_IO0>,
+			       <STM32F746_PC10_FUNC_QUADSPI_BK1_IO1>,
+			       <STM32F746_PD13_FUNC_QUADSPI_BK1_IO3>,
+			       <STM32F746_PE2_FUNC_QUADSPI_BK1_IO2>;
+			slew-rate = <2>;
+		};
+	};
+
+	fmc_pins: fmc at 0 {
+		  pins {
+			  pinmux = <STM32F746_PI10_FUNC_FMC_D31>,
+				 <STM32F746_PI9_FUNC_FMC_D30>,
+				 <STM32F746_PI7_FUNC_FMC_D29>,
+				 <STM32F746_PI6_FUNC_FMC_D28>,
+				 <STM32F746_PI3_FUNC_FMC_D27>,
+				 <STM32F746_PI2_FUNC_FMC_D26>,
+				 <STM32F746_PI1_FUNC_FMC_D25>,
+				 <STM32F746_PI0_FUNC_FMC_D24>,
+				 <STM32F746_PH15_FUNC_FMC_D23>,
+				 <STM32F746_PH14_FUNC_FMC_D22>,
+				 <STM32F746_PH13_FUNC_FMC_D21>,
+				 <STM32F746_PH12_FUNC_FMC_D20>,
+				 <STM32F746_PH11_FUNC_FMC_D19>,
+				 <STM32F746_PH10_FUNC_FMC_D18>,
+				 <STM32F746_PH9_FUNC_FMC_D17>,
+				 <STM32F746_PH8_FUNC_FMC_D16>,
+
+				 <STM32F746_PD10_FUNC_FMC_D15>,
+				 <STM32F746_PD9_FUNC_FMC_D14>,
+				 <STM32F746_PD8_FUNC_FMC_D13>,
+				 <STM32F746_PE15_FUNC_FMC_D12>,
+				 <STM32F746_PE14_FUNC_FMC_D11>,
+				 <STM32F746_PE13_FUNC_FMC_D10>,
+				 <STM32F746_PE12_FUNC_FMC_D9>,
+				 <STM32F746_PE11_FUNC_FMC_D8>,
+				 <STM32F746_PE10_FUNC_FMC_D7>,
+				 <STM32F746_PE9_FUNC_FMC_D6>,
+				 <STM32F746_PE8_FUNC_FMC_D5>,
+				 <STM32F746_PE7_FUNC_FMC_D4>,
+				 <STM32F746_PD1_FUNC_FMC_D3>,
+				 <STM32F746_PD0_FUNC_FMC_D2>,
+				 <STM32F746_PD15_FUNC_FMC_D1>,
+				 <STM32F746_PD14_FUNC_FMC_D0>,
+
+				 <STM32F746_PI5_FUNC_FMC_NBL3>,
+				 <STM32F746_PI4_FUNC_FMC_NBL2>,
+				 <STM32F746_PE1_FUNC_FMC_NBL1>,
+				 <STM32F746_PE0_FUNC_FMC_NBL0>,
+
+				 <STM32F746_PG5_FUNC_FMC_A15_FMC_BA1>,
+				 <STM32F746_PG4_FUNC_FMC_A14_FMC_BA0>,
+
+				 <STM32F746_PG1_FUNC_FMC_A11>,
+				 <STM32F746_PG0_FUNC_FMC_A10>,
+				 <STM32F746_PF15_FUNC_FMC_A9>,
+				 <STM32F746_PF14_FUNC_FMC_A8>,
+				 <STM32F746_PF13_FUNC_FMC_A7>,
+				 <STM32F746_PF12_FUNC_FMC_A6>,
+				 <STM32F746_PF5_FUNC_FMC_A5>,
+				 <STM32F746_PF4_FUNC_FMC_A4>,
+				 <STM32F746_PF3_FUNC_FMC_A3>,
+				 <STM32F746_PF2_FUNC_FMC_A2>,
+				 <STM32F746_PF1_FUNC_FMC_A1>,
+				 <STM32F746_PF0_FUNC_FMC_A0>,
+
+				 <STM32F746_PH3_FUNC_FMC_SDNE0>,
+				 <STM32F746_PH5_FUNC_FMC_SDNWE>,
+				 <STM32F746_PF11_FUNC_FMC_SDNRAS>,
+				 <STM32F746_PG15_FUNC_FMC_SDNCAS>,
+				 <STM32F746_PH2_FUNC_FMC_SDCKE0>,
+				 <STM32F746_PG8_FUNC_FMC_SDCLK>;
+			  slew-rate = <2>;
+		  };
+	  };
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&fmc {
+	pinctrl-0 = <&fmc_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mr-nbanks = <1>;
+	/* Memory configuration from sdram datasheet MT48LC_4M32_B2B5-6A */
+	bank1: bank at 0 {
+	       st,sdram-control = /bits/ 8 <NO_COL_8 NO_ROW_12 MWIDTH_32 BANKS_4
+	       				    CAS_3 SDCLK_2 RD_BURST_EN
+					    RD_PIPE_DL_0>;
+	       st,sdram-timing = /bits/ 8 <TMRD_2 TXSR_6 TRAS_4 TRC_6 TWR_2
+	       				   TRP_2 TRCD_2>;
+		/* refcount = (64msec/total_row_sdram)*freq - 20 */
+	       st,sdram-refcount = < 1542 >;
+       };
+};
+
+&mac {
+	status = "okay";
+	pinctrl-0 = <&ethernet_mii>;
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
+	};
+};
+
+&qspi {
+	pinctrl-0 = <&qspi_pins>;
+	status = "okay";
+
+	qflash0: n25q128a {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "micron,n25q128a13", "spi-flash";
+			spi-max-frequency = <108000000>;
+			spi-tx-bus-width = <1>;
+			spi-rx-bus-width = <1>;
+			memory-map = <0x90000000 0x1000000>;
+			reg = <0>;
+	};
+};
-- 
1.9.1

[U-Boot] [PATCH v4 18/18] stm32f7: remove not needed configuration from board config

[Vikas Manocha]

This patch removes:
	- CONFIG_CMD_MEM: enabled by default
	- CONFIG_DESIGNWARE_ETH : not being used anywhere.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
---
Changed in v4: None
Changed in v3: None
Changed in v2: None

 include/configs/stm32f746-disco.h | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/include/configs/stm32f746-disco.h b/include/configs/stm32f746-disco.h
index cc0f8fd..1ee5815 100644
--- a/include/configs/stm32f746-disco.h
+++ b/include/configs/stm32f746-disco.h
@@ -28,7 +28,6 @@
 #define CONFIG_STM32_FLASH
 #define CONFIG_STM32X7_SERIAL
 
-#define CONFIG_DESIGNWARE_ETH
 #define CONFIG_DW_GMAC_DEFAULT_DMA_PBL	(8)
 #define CONFIG_DW_ALTDESCRIPTOR
 #define CONFIG_MII
@@ -67,8 +66,6 @@
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
-
-#define CONFIG_CMD_MEM
 #define CONFIG_CMD_CACHE
 #define CONFIG_BOARD_LATE_INIT
 #define CONFIG_DISPLAY_BOARDINFO
-- 
1.9.1

[U-Boot] [PATCH v4 00/18] stm32f7: add sdram & gpio drivers

[Vikas MANOCHA]

Hi Tom,

> -----Original Message-----
> From: Vikas MANOCHA
> Sent: Monday, April 10, 2017 3:03 PM
> To: u-boot at lists.denx.de
> Cc: Vikas MANOCHA <vikas.manocha@st.com>
> Subject: [PATCH v4 00/18] stm32f7: add sdram & gpio drivers
> 
> This patchset :
> 	- adds stm32 sdram driver based on DM
> 	- adds stm32 gpio driver based on DM
> 	- uses clock & pin control drivers to replace board specific
> 	  configurations from code
> 	- corrects sdram parameters as per correct sdram part
> 	- adds support for stm32f769 board
> 

Please apply this patchset whenever you get time.

Cheers,
Vikas

> Changed in v4:
> - rebased to master.
> 
> Changed in v3:
> - made stm32_gpio_config() static.
> - moved common.h inclusion before clk.h
> 
> Changed in v2:
> - included files in correct order.
> - moved the pinctrl specific routine from gpio driver to pinctrl
> - used dev_get_addr() instead of fdtdec_get_addr_size_auto_parent() in
>   gpio driver.
> - pointed gpio name to bank name in device tree blob rather than copy.
> 
> Vikas Manocha (18):
>   stm32f7: use clock driver to enable qspi controller clock
>   stm32f7: sdram: move sdram driver code to ram drivers area
>   stm32f7: dm: add driver model support for sdram
>   ARM: DT: stm32f7: add sdram pin contol node
>   stm32f7: use driver model for sdram initialization
>   stm32f7: use clock driver to enable sdram controller clock
>   stm32f7: sdram: use sdram device tree node to configure sdram
>     controller
>   dm: gpio: Add driver for stm32f7 gpio controller
>   ARM: DT: stm32f7: add gpio device tree nodes
>   stm32f7: use stm32f7 gpio driver supporting driver model
>   stm32f746: to switch on user LED1 & read user button
>   stm32f7: stm32f746-disco: read memory info from device tree
>   stm32f7: enable board info read from device tree
>   stm32f7: sdram: correct sdram configuration as per micron sdram
>   stm32f7: increase the max no of pin configuration to 70
>   stm32f7: move board specific pin muxing to dts
>   stm32f7: add support for stm32f769 disco board
>   stm32f7: remove not needed configuration from board config
> 
>  arch/arm/dts/Makefile                         |   3 +-
>  arch/arm/dts/stm32f746-disco.dts              | 132 ++++++++++++
>  arch/arm/dts/stm32f746.dtsi                   | 151 ++++++++++---
>  arch/arm/dts/stm32f769-disco.dts              | 255 ++++++++++++++++++++++
>  arch/arm/include/asm/arch-stm32f7/gpio.h      |  21 +-
>  board/st/stm32f746-disco/stm32f746-disco.c    | 299 ++++++--------------------
>  configs/stm32f746-disco_defconfig             |   6 +
>  doc/device-tree-bindings/ram/st,stm32-fmc.txt |  51 +++++
>  drivers/clk/clk_stm32f7.c                     |  39 ----
>  drivers/gpio/Kconfig                          |   9 +
>  drivers/gpio/Makefile                         |   1 +
>  drivers/gpio/stm32f7_gpio.c                   | 135 ++++++++++++
>  drivers/pinctrl/pinctrl_stm32.c               |  50 ++++-
>  drivers/ram/Kconfig                           |   8 +
>  drivers/ram/Makefile                          |   1 +
>  drivers/ram/stm32_sdram.c                     | 179 +++++++++++++++
>  drivers/spi/stm32_qspi.c                      |  16 +-
>  include/configs/stm32f746-disco.h             |  11 +-
>  include/dt-bindings/memory/stm32-sdram.h      |  37 ++++
>  19 files changed, 1076 insertions(+), 328 deletions(-)  create mode 100644 arch/arm/dts/stm32f769-disco.dts  create mode 100644
> doc/device-tree-bindings/ram/st,stm32-fmc.txt
>  create mode 100644 drivers/gpio/stm32f7_gpio.c  create mode 100644 drivers/ram/stm32_sdram.c  create mode 100644 include/dt-
> bindings/memory/stm32-sdram.h
> 
> --
> 1.9.1

[U-Boot] [PATCH v4 00/18] stm32f7: add sdram & gpio drivers

[Tom Rini]

On Mon, Apr 24, 2017 at 07:39:55PM +0000, Vikas MANOCHA wrote:
> Hi Tom,
> 
> > -----Original Message-----
> > From: Vikas MANOCHA
> > Sent: Monday, April 10, 2017 3:03 PM
> > To: u-boot at lists.denx.de
> > Cc: Vikas MANOCHA <vikas.manocha@st.com>
> > Subject: [PATCH v4 00/18] stm32f7: add sdram & gpio drivers
> > 
> > This patchset :
> > 	- adds stm32 sdram driver based on DM
> > 	- adds stm32 gpio driver based on DM
> > 	- uses clock & pin control drivers to replace board specific
> > 	  configurations from code
> > 	- corrects sdram parameters as per correct sdram part
> > 	- adds support for stm32f769 board
> > 
> 
> Please apply this patchset whenever you get time.

Thanks.  I'll pick this up early next cycle.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170427/0688c2b4/attachment.sig>

[U-Boot] [U-Boot, v4, 01/18] stm32f7: use clock driver to enable qspi controller clock

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:50PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/f60f1b90/attachment.sig>

[U-Boot] [U-Boot, v4, 02/18] stm32f7: sdram: move sdram driver code to ram drivers area

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:51PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/07116877/attachment.sig>

[U-Boot] [U-Boot, v4, 03/18] stm32f7: dm: add driver model support for sdram

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:52PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/74e461eb/attachment.sig>

[U-Boot] [U-Boot, v4, 04/18] ARM: DT: stm32f7: add sdram pin contol node

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:53PM -0700, Vikas Manocha wrote:

> Also added DT binding doc for stm32 fmc(flexible memory controller).
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/f52cf117/attachment.sig>

[U-Boot] [U-Boot, v4, 05/18] stm32f7: use driver model for sdram initialization

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:54PM -0700, Vikas Manocha wrote:

> As driver model takes care of pin control configuraion, this patch also
> removes the sdram/fmc pin configuration.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/112e479e/attachment.sig>

[U-Boot] [U-Boot, v4, 06/18] stm32f7: use clock driver to enable sdram controller clock

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:55PM -0700, Vikas Manocha wrote:

> This patch also removes the sdram/fmc clock enable from board specific
> code.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/7a3045fc/attachment.sig>

[U-Boot] [U-Boot, v4, 07/18] stm32f7: sdram: use sdram device tree node to configure sdram controller

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:56PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/cf4df822/attachment.sig>

[U-Boot] [U-Boot, v4, 08/18] dm: gpio: Add driver for stm32f7 gpio controller

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:57PM -0700, Vikas Manocha wrote:

> This patch adds gpio driver supporting driver model for stm32f7 gpio.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/994851c9/attachment.sig>

[U-Boot] [U-Boot, v4, 09/18] ARM: DT: stm32f7: add gpio device tree nodes

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:58PM -0700, Vikas Manocha wrote:

> Also created alias for gpios for stm32f7 discovery board. Based on these
> aliases, it would be possible to get gpio devices by sequence.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/32f78fd1/attachment.sig>

[U-Boot] [U-Boot, v4, 10/18] stm32f7: use stm32f7 gpio driver supporting driver model

[Tom Rini]

On Mon, Apr 10, 2017 at 03:02:59PM -0700, Vikas Manocha wrote:

> With this gpio driver supporting DM, there is no need to enable clocks
> for different gpios (for pin muxing) in the board specific code.
> 
> Need to increase the allocatable area required before relocation from 0x400 to
> 0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/b84b5d44/attachment.sig>

[U-Boot] [U-Boot, v4, 11/18] stm32f746: to switch on user LED1 & read user button

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:00PM -0700, Vikas Manocha wrote:

> All discovery boards have one user button & one user LED. Here we are
> just reading the button status & switching ON the user LED.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/69d6203b/attachment.sig>

[U-Boot] [U-Boot, v4, 12/18] stm32f7: stm32f746-disco: read memory info from device tree

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:01PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/0c1653c0/attachment.sig>

[U-Boot] [U-Boot, v4, 13/18] stm32f7: enable board info read from device tree

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:02PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/7b2722e6/attachment.sig>

[U-Boot] [U-Boot, v4, 14/18] stm32f7: sdram: correct sdram configuration as per micron sdram

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:03PM -0700, Vikas Manocha wrote:

> Actually the sdram memory on stm32f746 discovery board is micron part
> MT48LC_4M32_B2B5_6A. This patch does the modification required in the
> device tree node & driver for the same.
> 
> Also we are passing here all the timing parameters in terms of clock
> cycles, so no need to convert time(ns or ms) to cycles.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/1f63679b/attachment.sig>

[U-Boot] [U-Boot, v4, 15/18] stm32f7: increase the max no of pin configuration to 70

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:04PM -0700, Vikas Manocha wrote:

> The number of pins to be configured could be more than 50 e.g. in case
> of sdram controller, there are about 56 pins (32 data lines, 12 address
> & some control signals).
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/2fb870d7/attachment.sig>

[U-Boot] [U-Boot, v4, 16/18] stm32f7: move board specific pin muxing to dts

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:05PM -0700, Vikas Manocha wrote:

> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/c1446e73/attachment.sig>

[U-Boot] [U-Boot, v4, 17/18] stm32f7: add support for stm32f769 disco board

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:06PM -0700, Vikas Manocha wrote:

> This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
> 512KB RAM.
> STM32F769 lines offer the performance of the Cortex-M7 core (with double
> precision floating point unit) running up to 216 MHz.
> 
> To compile for stm32f769 board, use same defconfig as stm32f746-disco,
> the only difference is to pass "DEVICE_TREE=stm32f769-disco".
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/ea9c6ad9/attachment.sig>

[U-Boot] [U-Boot, v4, 18/18] stm32f7: remove not needed configuration from board config

[Tom Rini]

On Mon, Apr 10, 2017 at 03:03:07PM -0700, Vikas Manocha wrote:

> This patch removes:
> 	- CONFIG_CMD_MEM: enabled by default
> 	- CONFIG_DESIGNWARE_ETH : not being used anywhere.
> 
> Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
> cc: Christophe KERELLO <christophe.kerello@st.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170508/1e6f8a53/attachment.sig>