* [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: Kukjin Kim, Krzysztof Kozlowski, devicetree, linux-arm-kernel,
linux-samsung-soc, linux-kernel
Cc: Marek Szyprowski
Hi,
Tested with comparing decompiled DTBs (dtx_diff). No differences.
Best regards,
Krzysztof
Krzysztof Kozlowski (2):
ARM: dts: exynos: Use human-friendly symbols for interrupt flags in
board sources
ARM: dts: exynos: Use human-friendly symbols for GIC interrupt
properties
arch/arm/boot/dts/exynos3250-monk.dts | 6 +-
arch/arm/boot/dts/exynos3250-rinato.dts | 6 +-
arch/arm/boot/dts/exynos4210-origen.dts | 2 +-
arch/arm/boot/dts/exynos4210-trats.dts | 4 +-
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 +-
arch/arm/boot/dts/exynos4412-odroidx.dts | 2 +-
arch/arm/boot/dts/exynos4412-trats2.dts | 8 +--
arch/arm/boot/dts/exynos5.dtsi | 84 +++++++++++------------
arch/arm/boot/dts/exynos5250.dtsi | 8 +--
arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +-
arch/arm/boot/dts/exynos5420.dtsi | 76 ++++++++++----------
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 2 +-
arch/arm/boot/dts/exynos5440.dtsi | 2 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +-
14 files changed, 107 insertions(+), 107 deletions(-)
--
2.9.3
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
Tested with comparing decompiled DTBs (dtx_diff). No differences.
Best regards,
Krzysztof
Krzysztof Kozlowski (2):
ARM: dts: exynos: Use human-friendly symbols for interrupt flags in
board sources
ARM: dts: exynos: Use human-friendly symbols for GIC interrupt
properties
arch/arm/boot/dts/exynos3250-monk.dts | 6 +-
arch/arm/boot/dts/exynos3250-rinato.dts | 6 +-
arch/arm/boot/dts/exynos4210-origen.dts | 2 +-
arch/arm/boot/dts/exynos4210-trats.dts | 4 +-
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 +-
arch/arm/boot/dts/exynos4412-odroidx.dts | 2 +-
arch/arm/boot/dts/exynos4412-trats2.dts | 8 +--
arch/arm/boot/dts/exynos5.dtsi | 84 +++++++++++------------
arch/arm/boot/dts/exynos5250.dtsi | 8 +--
arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +-
arch/arm/boot/dts/exynos5420.dtsi | 76 ++++++++++----------
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 2 +-
arch/arm/boot/dts/exynos5440.dtsi | 2 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 +-
14 files changed, 107 insertions(+), 107 deletions(-)
--
2.9.3
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: Kukjin Kim, Krzysztof Kozlowski, devicetree, linux-arm-kernel,
linux-samsung-soc, linux-kernel
Cc: Marek Szyprowski
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
arch/arm/boot/dts/exynos3250-monk.dts | 6 +++---
arch/arm/boot/dts/exynos3250-rinato.dts | 6 +++---
arch/arm/boot/dts/exynos4210-origen.dts | 2 +-
arch/arm/boot/dts/exynos4210-trats.dts | 4 ++--
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 +++---
arch/arm/boot/dts/exynos4412-odroidx.dts | 2 +-
arch/arm/boot/dts/exynos4412-trats2.dts | 8 ++++----
arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 ++--
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 2 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 ++--
10 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index cccfe4b791d1..accee81da266 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -67,7 +67,7 @@
max77836: subpmic@25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -191,7 +191,7 @@
s2mps14_pmic@66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -414,7 +414,7 @@
fuelgauge@36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index c9f191ca7b9c..118235b72e90 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -58,7 +58,7 @@
max77836: subpmic@25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -295,7 +295,7 @@
s2mps14_pmic@66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -626,7 +626,7 @@
fuelgauge@36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 312650e2450f..084fcc5574ef 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -151,7 +151,7 @@
compatible = "maxim,max8997-pmic";
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <4 0>, <3 0>;
+ interrupts = <4 IRQ_TYPE_NONE>, <3 IRQ_TYPE_NONE>;
max8997,pmic-buck1-dvs-voltage = <1350000>;
max8997,pmic-buck2-dvs-voltage = <1100000>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 1743ca850070..645feffb9239 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -281,7 +281,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&tsp_reg>;
@@ -302,7 +302,7 @@
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 0f1ff792fe44..219d587c5a85 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -32,7 +32,7 @@
power_key {
interrupt-parent = <&gpx1>;
- interrupts = <3 0>;
+ interrupts = <3 IRQ_TYPE_NONE>;
gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
label = "power key";
@@ -266,7 +266,7 @@
max77686: pmic@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&max77686_irq>;
reg = <0x09>;
@@ -484,7 +484,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
+ interrupts = <0 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index 46b931eec228..97882267ef09 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -44,7 +44,7 @@
home_key {
interrupt-parent = <&gpx2>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_HOME>;
label = "home key";
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 82221a00444d..35e9b94b86b8 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -144,7 +144,7 @@
max77693@66 {
compatible = "maxim,max77693";
interrupt-parent = <&gpx1>;
- interrupts = <5 2>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
reg = <0x66>;
regulators {
@@ -224,7 +224,7 @@
compatible = "capella,cm36651";
reg = <0x18>;
interrupt-parent = <&gpx0>;
- interrupts = <2 2>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
vled-supply = <&ps_als_reg>;
};
};
@@ -573,7 +573,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpm2>;
- interrupts = <3 2>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&ldo23_reg>;
@@ -611,7 +611,7 @@
max77686: max77686_pmic@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x09>;
#clock-cells = <1>;
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 2cd65699a29c..f9a75bfd3f2b 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -603,7 +603,7 @@
max98090: codec@10 {
compatible = "maxim,max98090";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98090_irq>;
@@ -944,7 +944,7 @@
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
index 9493923ec652..c0b85981c6bf 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
@@ -49,7 +49,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index ecf1c916e8fc..953dc8677dc8 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -603,7 +603,7 @@
max98091: codec@10 {
compatible = "maxim,max98091";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98091_irq>;
@@ -913,7 +913,7 @@
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
--
2.9.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: Kukjin Kim, Krzysztof Kozlowski,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Marek Szyprowski
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/exynos3250-monk.dts | 6 +++---
arch/arm/boot/dts/exynos3250-rinato.dts | 6 +++---
arch/arm/boot/dts/exynos4210-origen.dts | 2 +-
arch/arm/boot/dts/exynos4210-trats.dts | 4 ++--
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 +++---
arch/arm/boot/dts/exynos4412-odroidx.dts | 2 +-
arch/arm/boot/dts/exynos4412-trats2.dts | 8 ++++----
arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 ++--
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 2 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 ++--
10 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index cccfe4b791d1..accee81da266 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -67,7 +67,7 @@
max77836: subpmic@25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -191,7 +191,7 @@
s2mps14_pmic@66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -414,7 +414,7 @@
fuelgauge@36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index c9f191ca7b9c..118235b72e90 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -58,7 +58,7 @@
max77836: subpmic@25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -295,7 +295,7 @@
s2mps14_pmic@66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -626,7 +626,7 @@
fuelgauge@36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 312650e2450f..084fcc5574ef 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -151,7 +151,7 @@
compatible = "maxim,max8997-pmic";
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <4 0>, <3 0>;
+ interrupts = <4 IRQ_TYPE_NONE>, <3 IRQ_TYPE_NONE>;
max8997,pmic-buck1-dvs-voltage = <1350000>;
max8997,pmic-buck2-dvs-voltage = <1100000>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 1743ca850070..645feffb9239 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -281,7 +281,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&tsp_reg>;
@@ -302,7 +302,7 @@
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 0f1ff792fe44..219d587c5a85 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -32,7 +32,7 @@
power_key {
interrupt-parent = <&gpx1>;
- interrupts = <3 0>;
+ interrupts = <3 IRQ_TYPE_NONE>;
gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
label = "power key";
@@ -266,7 +266,7 @@
max77686: pmic@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&max77686_irq>;
reg = <0x09>;
@@ -484,7 +484,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
+ interrupts = <0 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index 46b931eec228..97882267ef09 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -44,7 +44,7 @@
home_key {
interrupt-parent = <&gpx2>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_HOME>;
label = "home key";
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 82221a00444d..35e9b94b86b8 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -144,7 +144,7 @@
max77693@66 {
compatible = "maxim,max77693";
interrupt-parent = <&gpx1>;
- interrupts = <5 2>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
reg = <0x66>;
regulators {
@@ -224,7 +224,7 @@
compatible = "capella,cm36651";
reg = <0x18>;
interrupt-parent = <&gpx0>;
- interrupts = <2 2>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
vled-supply = <&ps_als_reg>;
};
};
@@ -573,7 +573,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpm2>;
- interrupts = <3 2>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&ldo23_reg>;
@@ -611,7 +611,7 @@
max77686: max77686_pmic@09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x09>;
#clock-cells = <1>;
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 2cd65699a29c..f9a75bfd3f2b 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -603,7 +603,7 @@
max98090: codec@10 {
compatible = "maxim,max98090";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98090_irq>;
@@ -944,7 +944,7 @@
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
index 9493923ec652..c0b85981c6bf 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
@@ -49,7 +49,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index ecf1c916e8fc..953dc8677dc8 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -603,7 +603,7 @@
max98091: codec@10 {
compatible = "maxim,max98091";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98091_irq>;
@@ -913,7 +913,7 @@
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: linux-arm-kernel
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
arch/arm/boot/dts/exynos3250-monk.dts | 6 +++---
arch/arm/boot/dts/exynos3250-rinato.dts | 6 +++---
arch/arm/boot/dts/exynos4210-origen.dts | 2 +-
arch/arm/boot/dts/exynos4210-trats.dts | 4 ++--
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 6 +++---
arch/arm/boot/dts/exynos4412-odroidx.dts | 2 +-
arch/arm/boot/dts/exynos4412-trats2.dts | 8 ++++----
arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 ++--
arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi | 2 +-
arch/arm/boot/dts/exynos5800-peach-pi.dts | 4 ++--
10 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index cccfe4b791d1..accee81da266 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -67,7 +67,7 @@
max77836: subpmic at 25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -191,7 +191,7 @@
s2mps14_pmic at 66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -414,7 +414,7 @@
fuelgauge at 36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index c9f191ca7b9c..118235b72e90 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -58,7 +58,7 @@
max77836: subpmic at 25 {
compatible = "maxim,max77836";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
reg = <0x25>;
wakeup-source;
@@ -295,7 +295,7 @@
s2mps14_pmic at 66 {
compatible = "samsung,s2mps14-pmic";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x66>;
wakeup-source;
@@ -626,7 +626,7 @@
fuelgauge at 36 {
compatible = "maxim,max77836-battery";
interrupt-parent = <&gpx1>;
- interrupts = <2 8>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
reg = <0x36>;
};
};
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 312650e2450f..084fcc5574ef 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -151,7 +151,7 @@
compatible = "maxim,max8997-pmic";
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <4 0>, <3 0>;
+ interrupts = <4 IRQ_TYPE_NONE>, <3 IRQ_TYPE_NONE>;
max8997,pmic-buck1-dvs-voltage = <1350000>;
max8997,pmic-buck2-dvs-voltage = <1100000>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 1743ca850070..645feffb9239 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -281,7 +281,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&tsp_reg>;
@@ -302,7 +302,7 @@
reg = <0x66>;
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
max8997,pmic-buck1-uses-gpio-dvs;
max8997,pmic-buck2-uses-gpio-dvs;
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 0f1ff792fe44..219d587c5a85 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -32,7 +32,7 @@
power_key {
interrupt-parent = <&gpx1>;
- interrupts = <3 0>;
+ interrupts = <3 IRQ_TYPE_NONE>;
gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
label = "power key";
@@ -266,7 +266,7 @@
max77686: pmic at 09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&max77686_irq>;
reg = <0x09>;
@@ -484,7 +484,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
+ interrupts = <0 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index 46b931eec228..97882267ef09 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -44,7 +44,7 @@
home_key {
interrupt-parent = <&gpx2>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_HOME>;
label = "home key";
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 82221a00444d..35e9b94b86b8 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -144,7 +144,7 @@
max77693 at 66 {
compatible = "maxim,max77693";
interrupt-parent = <&gpx1>;
- interrupts = <5 2>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
reg = <0x66>;
regulators {
@@ -224,7 +224,7 @@
compatible = "capella,cm36651";
reg = <0x18>;
interrupt-parent = <&gpx0>;
- interrupts = <2 2>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
vled-supply = <&ps_als_reg>;
};
};
@@ -573,7 +573,7 @@
compatible = "melfas,mms114";
reg = <0x48>;
interrupt-parent = <&gpm2>;
- interrupts = <3 2>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
x-size = <720>;
y-size = <1280>;
avdd-supply = <&ldo23_reg>;
@@ -611,7 +611,7 @@
max77686: max77686_pmic at 09 {
compatible = "maxim,max77686";
interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
+ interrupts = <7 IRQ_TYPE_NONE>;
reg = <0x09>;
#clock-cells = <1>;
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 2cd65699a29c..f9a75bfd3f2b 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -603,7 +603,7 @@
max98090: codec at 10 {
compatible = "maxim,max98090";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98090_irq>;
@@ -944,7 +944,7 @@
cros_ec: cros-ec at 0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
index 9493923ec652..c0b85981c6bf 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-audio.dtsi
@@ -49,7 +49,7 @@
compatible = "maxim,max98090";
reg = <0x10>;
interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
clocks = <&i2s0 CLK_I2S_CDCLK>;
clock-names = "mclk";
#sound-dai-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index ecf1c916e8fc..953dc8677dc8 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -603,7 +603,7 @@
max98091: codec at 10 {
compatible = "maxim,max98091";
reg = <0x10>;
- interrupts = <2 0>;
+ interrupts = <2 IRQ_TYPE_NONE>;
interrupt-parent = <&gpx0>;
pinctrl-names = "default";
pinctrl-0 = <&max98091_irq>;
@@ -913,7 +913,7 @@
cros_ec: cros-ec at 0 {
compatible = "google,cros-ec-spi";
interrupt-parent = <&gpx1>;
- interrupts = <5 0>;
+ interrupts = <5 IRQ_TYPE_NONE>;
pinctrl-names = "default";
pinctrl-0 = <&ec_spi_cs &ec_irq>;
reg = <0>;
--
2.9.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties
2017-06-02 18:13 ` Krzysztof Kozlowski
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: Kukjin Kim, Krzysztof Kozlowski, devicetree, linux-arm-kernel,
linux-samsung-soc, linux-kernel
Cc: Marek Szyprowski
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
arch/arm/boot/dts/exynos5.dtsi | 84 +++++++++++++++++++--------------------
arch/arm/boot/dts/exynos5250.dtsi | 8 ++--
arch/arm/boot/dts/exynos5420.dtsi | 76 +++++++++++++++++------------------
arch/arm/boot/dts/exynos5440.dtsi | 2 +-
4 files changed, 85 insertions(+), 85 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index b74c5379ca26..66d22521c976 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -55,38 +55,38 @@
interrupt-controller;
samsung,combiner-nr = <32>;
reg = <0x10440000 0x1000>;
- interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>,
- <0 1 IRQ_TYPE_LEVEL_HIGH>,
- <0 2 IRQ_TYPE_LEVEL_HIGH>,
- <0 3 IRQ_TYPE_LEVEL_HIGH>,
- <0 4 IRQ_TYPE_LEVEL_HIGH>,
- <0 5 IRQ_TYPE_LEVEL_HIGH>,
- <0 6 IRQ_TYPE_LEVEL_HIGH>,
- <0 7 IRQ_TYPE_LEVEL_HIGH>,
- <0 8 IRQ_TYPE_LEVEL_HIGH>,
- <0 9 IRQ_TYPE_LEVEL_HIGH>,
- <0 10 IRQ_TYPE_LEVEL_HIGH>,
- <0 11 IRQ_TYPE_LEVEL_HIGH>,
- <0 12 IRQ_TYPE_LEVEL_HIGH>,
- <0 13 IRQ_TYPE_LEVEL_HIGH>,
- <0 14 IRQ_TYPE_LEVEL_HIGH>,
- <0 15 IRQ_TYPE_LEVEL_HIGH>,
- <0 16 IRQ_TYPE_LEVEL_HIGH>,
- <0 17 IRQ_TYPE_LEVEL_HIGH>,
- <0 18 IRQ_TYPE_LEVEL_HIGH>,
- <0 19 IRQ_TYPE_LEVEL_HIGH>,
- <0 20 IRQ_TYPE_LEVEL_HIGH>,
- <0 21 IRQ_TYPE_LEVEL_HIGH>,
- <0 22 IRQ_TYPE_LEVEL_HIGH>,
- <0 23 IRQ_TYPE_LEVEL_HIGH>,
- <0 24 IRQ_TYPE_LEVEL_HIGH>,
- <0 25 IRQ_TYPE_LEVEL_HIGH>,
- <0 26 IRQ_TYPE_LEVEL_HIGH>,
- <0 27 IRQ_TYPE_LEVEL_HIGH>,
- <0 28 IRQ_TYPE_LEVEL_HIGH>,
- <0 29 IRQ_TYPE_LEVEL_HIGH>,
- <0 30 IRQ_TYPE_LEVEL_HIGH>,
- <0 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
};
gic: interrupt-controller@10481000 {
@@ -109,31 +109,31 @@
serial_0: serial@12C00000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C00000 0x100>;
- interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
};
serial_1: serial@12C10000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C10000 0x100>;
- interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
};
serial_2: serial@12C20000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C20000 0x100>;
- interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
};
serial_3: serial@12C30000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C30000 0x100>;
- interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
};
i2c_0: i2c@12C60000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C60000 0x100>;
- interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -143,7 +143,7 @@
i2c_1: i2c@12C70000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C70000 0x100>;
- interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -153,7 +153,7 @@
i2c_2: i2c@12C80000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C80000 0x100>;
- interrupts = <0 58 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -163,7 +163,7 @@
i2c_3: i2c@12C90000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C90000 0x100>;
- interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -180,8 +180,8 @@
rtc: rtc@101E0000 {
compatible = "samsung,s3c6410-rtc";
reg = <0x101E0000 0x100>;
- interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>,
- <0 44 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 79c9c885613a..f35f00464631 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -153,10 +153,10 @@
timer {
compatible = "arm,armv7-timer";
- interrupts = <1 13 0xf08>,
- <1 14 0xf08>,
- <1 11 0xf08>,
- <1 10 0xf08>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
/*
* Unfortunately we need this since some versions
* of U-Boot on Exynos don't set the CNTFRQ register,
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index 0db0bcf8da36..e8c6acfbb751 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -193,7 +193,7 @@
mfc: codec@11000000 {
compatible = "samsung,mfc-v7";
reg = <0x11000000 0x10000>;
- interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MFC>;
clock-names = "mfc";
power-domains = <&mfc_pd>;
@@ -203,7 +203,7 @@
mmc_0: mmc@12200000 {
compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12200000 0x2000>;
@@ -215,7 +215,7 @@
mmc_1: mmc@12210000 {
compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12210000 0x2000>;
@@ -227,7 +227,7 @@
mmc_2: mmc@12220000 {
compatible = "samsung,exynos5420-dw-mshc";
- interrupts = <0 77 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12220000 0x1000>;
@@ -325,37 +325,37 @@
pinctrl_0: pinctrl@13400000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x13400000 0x1000>;
- interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
wakeup-interrupt-controller {
compatible = "samsung,exynos4210-wakeup-eint";
interrupt-parent = <&gic>;
- interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
};
};
pinctrl_1: pinctrl@13410000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x13410000 0x1000>;
- interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_2: pinctrl@14000000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x14000000 0x1000>;
- interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_3: pinctrl@14010000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x14010000 0x1000>;
- interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_4: pinctrl@03860000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x03860000 0x1000>;
- interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
};
amba {
@@ -368,7 +368,7 @@
adma: adma@03880000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x03880000 0x1000>;
- interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock_audss EXYNOS_ADMA>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -379,7 +379,7 @@
pdma0: pdma@121A0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x121A0000 0x1000>;
- interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_PDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -390,7 +390,7 @@
pdma1: pdma@121B0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x121B0000 0x1000>;
- interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_PDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -401,7 +401,7 @@
mdma0: mdma@10800000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x10800000 0x1000>;
- interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -412,7 +412,7 @@
mdma1: mdma@11C10000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x11C10000 0x1000>;
- interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -484,7 +484,7 @@
spi_0: spi@12d20000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d20000 0x100>;
- interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma0 5
&pdma0 4>;
dma-names = "tx", "rx";
@@ -500,7 +500,7 @@
spi_1: spi@12d30000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d30000 0x100>;
- interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma1 5
&pdma1 4>;
dma-names = "tx", "rx";
@@ -516,7 +516,7 @@
spi_2: spi@12d40000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d40000 0x100>;
- interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma0 7
&pdma0 6>;
dma-names = "tx", "rx";
@@ -544,7 +544,7 @@
dsi@14500000 {
compatible = "samsung,exynos5410-mipi-dsi";
reg = <0x14500000 0x10000>;
- interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
phys = <&mipi_phy 1>;
phy-names = "dsim";
clocks = <&clock CLK_DSIM1>, <&clock CLK_SCLK_MIPI1>;
@@ -557,7 +557,7 @@
adc: adc@12D10000 {
compatible = "samsung,exynos-adc-v2";
reg = <0x12D10000 0x100>;
- interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TSADC>;
clock-names = "adc";
#io-channel-cells = <1>;
@@ -569,7 +569,7 @@
hsi2c_8: i2c@12E00000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E00000 0x1000>;
- interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -582,7 +582,7 @@
hsi2c_9: i2c@12E10000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E10000 0x1000>;
- interrupts = <0 88 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -595,7 +595,7 @@
hsi2c_10: i2c@12E20000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E20000 0x1000>;
- interrupts = <0 203 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -608,7 +608,7 @@
hdmi: hdmi@14530000 {
compatible = "samsung,exynos5420-hdmi";
reg = <0x14530000 0x70000>;
- interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
<&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
<&clock CLK_MOUT_HDMI>;
@@ -627,7 +627,7 @@
mixer: mixer@14450000 {
compatible = "samsung,exynos5420-mixer";
reg = <0x14450000 0x10000>;
- interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
<&clock CLK_SCLK_HDMI>;
clock-names = "mixer", "hdmi", "sclk_hdmi";
@@ -638,7 +638,7 @@
rotator: rotator@11C00000 {
compatible = "samsung,exynos5250-rotator";
reg = <0x11C00000 0x64>;
- interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_ROTATOR>;
clock-names = "rotator";
iommus = <&sysmmu_rotator>;
@@ -647,7 +647,7 @@
gsc_0: video-scaler@13e00000 {
compatible = "samsung,exynos5-gsc";
reg = <0x13e00000 0x1000>;
- interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_GSCL0>;
clock-names = "gscl";
power-domains = <&gsc_pd>;
@@ -657,7 +657,7 @@
gsc_1: video-scaler@13e10000 {
compatible = "samsung,exynos5-gsc";
reg = <0x13e10000 0x1000>;
- interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_GSCL1>;
clock-names = "gscl";
power-domains = <&gsc_pd>;
@@ -667,7 +667,7 @@
jpeg_0: jpeg@11F50000 {
compatible = "samsung,exynos5420-jpeg";
reg = <0x11F50000 0x1000>;
- interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "jpeg";
clocks = <&clock CLK_JPEG>;
iommus = <&sysmmu_jpeg0>;
@@ -676,7 +676,7 @@
jpeg_1: jpeg@11F60000 {
compatible = "samsung,exynos5420-jpeg";
reg = <0x11F60000 0x1000>;
- interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "jpeg";
clocks = <&clock CLK_JPEG2>;
iommus = <&sysmmu_jpeg1>;
@@ -696,7 +696,7 @@
tmu_cpu0: tmu@10060000 {
compatible = "samsung,exynos5420-tmu";
reg = <0x10060000 0x100>;
- interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -705,7 +705,7 @@
tmu_cpu1: tmu@10064000 {
compatible = "samsung,exynos5420-tmu";
reg = <0x10064000 0x100>;
- interrupts = <0 183 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -714,7 +714,7 @@
tmu_cpu2: tmu@10068000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x10068000 0x100>, <0x1006c000 0x4>;
- interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -723,7 +723,7 @@
tmu_cpu3: tmu@1006c000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
- interrupts = <0 185 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -732,7 +732,7 @@
tmu_gpu: tmu@100a0000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x100a0000 0x100>, <0x10068000 0x4>;
- interrupts = <0 215 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -804,7 +804,7 @@
sysmmu_scaler1r: sysmmu@0x12890000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x12890000 0x1000>;
- interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
#iommu-cells = <0>;
@@ -813,7 +813,7 @@
sysmmu_scaler2r: sysmmu@0x128A0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128A0000 0x1000>;
- interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
#iommu-cells = <0>;
@@ -872,7 +872,7 @@
sysmmu_jpeg1: sysmmu@0x11F20000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11F20000 0x1000>;
- interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_JPEG2>, <&clock CLK_JPEG2>;
#iommu-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index a4ea018464fc..bc4954e69f7b 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -200,7 +200,7 @@
compatible = "snps,dwmac-3.70a", "snps,dwmac";
reg = <0x00230000 0x8000>;
interrupt-parent = <&gic>;
- interrupts = <GIC_SPI 31 4>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
phy-mode = "sgmii";
clocks = <&clock CLK_GMAC0>;
--
2.9.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties
@ 2017-06-02 18:13 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-02 18:13 UTC (permalink / raw)
To: linux-arm-kernel
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
arch/arm/boot/dts/exynos5.dtsi | 84 +++++++++++++++++++--------------------
arch/arm/boot/dts/exynos5250.dtsi | 8 ++--
arch/arm/boot/dts/exynos5420.dtsi | 76 +++++++++++++++++------------------
arch/arm/boot/dts/exynos5440.dtsi | 2 +-
4 files changed, 85 insertions(+), 85 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index b74c5379ca26..66d22521c976 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -55,38 +55,38 @@
interrupt-controller;
samsung,combiner-nr = <32>;
reg = <0x10440000 0x1000>;
- interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>,
- <0 1 IRQ_TYPE_LEVEL_HIGH>,
- <0 2 IRQ_TYPE_LEVEL_HIGH>,
- <0 3 IRQ_TYPE_LEVEL_HIGH>,
- <0 4 IRQ_TYPE_LEVEL_HIGH>,
- <0 5 IRQ_TYPE_LEVEL_HIGH>,
- <0 6 IRQ_TYPE_LEVEL_HIGH>,
- <0 7 IRQ_TYPE_LEVEL_HIGH>,
- <0 8 IRQ_TYPE_LEVEL_HIGH>,
- <0 9 IRQ_TYPE_LEVEL_HIGH>,
- <0 10 IRQ_TYPE_LEVEL_HIGH>,
- <0 11 IRQ_TYPE_LEVEL_HIGH>,
- <0 12 IRQ_TYPE_LEVEL_HIGH>,
- <0 13 IRQ_TYPE_LEVEL_HIGH>,
- <0 14 IRQ_TYPE_LEVEL_HIGH>,
- <0 15 IRQ_TYPE_LEVEL_HIGH>,
- <0 16 IRQ_TYPE_LEVEL_HIGH>,
- <0 17 IRQ_TYPE_LEVEL_HIGH>,
- <0 18 IRQ_TYPE_LEVEL_HIGH>,
- <0 19 IRQ_TYPE_LEVEL_HIGH>,
- <0 20 IRQ_TYPE_LEVEL_HIGH>,
- <0 21 IRQ_TYPE_LEVEL_HIGH>,
- <0 22 IRQ_TYPE_LEVEL_HIGH>,
- <0 23 IRQ_TYPE_LEVEL_HIGH>,
- <0 24 IRQ_TYPE_LEVEL_HIGH>,
- <0 25 IRQ_TYPE_LEVEL_HIGH>,
- <0 26 IRQ_TYPE_LEVEL_HIGH>,
- <0 27 IRQ_TYPE_LEVEL_HIGH>,
- <0 28 IRQ_TYPE_LEVEL_HIGH>,
- <0 29 IRQ_TYPE_LEVEL_HIGH>,
- <0 30 IRQ_TYPE_LEVEL_HIGH>,
- <0 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
};
gic: interrupt-controller at 10481000 {
@@ -109,31 +109,31 @@
serial_0: serial at 12C00000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C00000 0x100>;
- interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
};
serial_1: serial at 12C10000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C10000 0x100>;
- interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
};
serial_2: serial at 12C20000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C20000 0x100>;
- interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
};
serial_3: serial at 12C30000 {
compatible = "samsung,exynos4210-uart";
reg = <0x12C30000 0x100>;
- interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
};
i2c_0: i2c at 12C60000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C60000 0x100>;
- interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -143,7 +143,7 @@
i2c_1: i2c at 12C70000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C70000 0x100>;
- interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -153,7 +153,7 @@
i2c_2: i2c at 12C80000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C80000 0x100>;
- interrupts = <0 58 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -163,7 +163,7 @@
i2c_3: i2c at 12C90000 {
compatible = "samsung,s3c2440-i2c";
reg = <0x12C90000 0x100>;
- interrupts = <0 59 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
samsung,sysreg-phandle = <&sysreg_system_controller>;
@@ -180,8 +180,8 @@
rtc: rtc at 101E0000 {
compatible = "samsung,s3c6410-rtc";
reg = <0x101E0000 0x100>;
- interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>,
- <0 44 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 79c9c885613a..f35f00464631 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -153,10 +153,10 @@
timer {
compatible = "arm,armv7-timer";
- interrupts = <1 13 0xf08>,
- <1 14 0xf08>,
- <1 11 0xf08>,
- <1 10 0xf08>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
/*
* Unfortunately we need this since some versions
* of U-Boot on Exynos don't set the CNTFRQ register,
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index 0db0bcf8da36..e8c6acfbb751 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -193,7 +193,7 @@
mfc: codec at 11000000 {
compatible = "samsung,mfc-v7";
reg = <0x11000000 0x10000>;
- interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MFC>;
clock-names = "mfc";
power-domains = <&mfc_pd>;
@@ -203,7 +203,7 @@
mmc_0: mmc at 12200000 {
compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12200000 0x2000>;
@@ -215,7 +215,7 @@
mmc_1: mmc at 12210000 {
compatible = "samsung,exynos5420-dw-mshc-smu";
- interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12210000 0x2000>;
@@ -227,7 +227,7 @@
mmc_2: mmc at 12220000 {
compatible = "samsung,exynos5420-dw-mshc";
- interrupts = <0 77 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12220000 0x1000>;
@@ -325,37 +325,37 @@
pinctrl_0: pinctrl at 13400000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x13400000 0x1000>;
- interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
wakeup-interrupt-controller {
compatible = "samsung,exynos4210-wakeup-eint";
interrupt-parent = <&gic>;
- interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
};
};
pinctrl_1: pinctrl at 13410000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x13410000 0x1000>;
- interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_2: pinctrl at 14000000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x14000000 0x1000>;
- interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_3: pinctrl at 14010000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x14010000 0x1000>;
- interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
};
pinctrl_4: pinctrl at 03860000 {
compatible = "samsung,exynos5420-pinctrl";
reg = <0x03860000 0x1000>;
- interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
};
amba {
@@ -368,7 +368,7 @@
adma: adma at 03880000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x03880000 0x1000>;
- interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock_audss EXYNOS_ADMA>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -379,7 +379,7 @@
pdma0: pdma at 121A0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x121A0000 0x1000>;
- interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_PDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -390,7 +390,7 @@
pdma1: pdma at 121B0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x121B0000 0x1000>;
- interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_PDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -401,7 +401,7 @@
mdma0: mdma at 10800000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x10800000 0x1000>;
- interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -412,7 +412,7 @@
mdma1: mdma at 11C10000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x11C10000 0x1000>;
- interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
@@ -484,7 +484,7 @@
spi_0: spi at 12d20000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d20000 0x100>;
- interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma0 5
&pdma0 4>;
dma-names = "tx", "rx";
@@ -500,7 +500,7 @@
spi_1: spi at 12d30000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d30000 0x100>;
- interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma1 5
&pdma1 4>;
dma-names = "tx", "rx";
@@ -516,7 +516,7 @@
spi_2: spi at 12d40000 {
compatible = "samsung,exynos4210-spi";
reg = <0x12d40000 0x100>;
- interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&pdma0 7
&pdma0 6>;
dma-names = "tx", "rx";
@@ -544,7 +544,7 @@
dsi at 14500000 {
compatible = "samsung,exynos5410-mipi-dsi";
reg = <0x14500000 0x10000>;
- interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
phys = <&mipi_phy 1>;
phy-names = "dsim";
clocks = <&clock CLK_DSIM1>, <&clock CLK_SCLK_MIPI1>;
@@ -557,7 +557,7 @@
adc: adc at 12D10000 {
compatible = "samsung,exynos-adc-v2";
reg = <0x12D10000 0x100>;
- interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TSADC>;
clock-names = "adc";
#io-channel-cells = <1>;
@@ -569,7 +569,7 @@
hsi2c_8: i2c at 12E00000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E00000 0x1000>;
- interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -582,7 +582,7 @@
hsi2c_9: i2c at 12E10000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E10000 0x1000>;
- interrupts = <0 88 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -595,7 +595,7 @@
hsi2c_10: i2c at 12E20000 {
compatible = "samsung,exynos5250-hsi2c";
reg = <0x12E20000 0x1000>;
- interrupts = <0 203 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
@@ -608,7 +608,7 @@
hdmi: hdmi at 14530000 {
compatible = "samsung,exynos5420-hdmi";
reg = <0x14530000 0x70000>;
- interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
<&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
<&clock CLK_MOUT_HDMI>;
@@ -627,7 +627,7 @@
mixer: mixer at 14450000 {
compatible = "samsung,exynos5420-mixer";
reg = <0x14450000 0x10000>;
- interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
<&clock CLK_SCLK_HDMI>;
clock-names = "mixer", "hdmi", "sclk_hdmi";
@@ -638,7 +638,7 @@
rotator: rotator at 11C00000 {
compatible = "samsung,exynos5250-rotator";
reg = <0x11C00000 0x64>;
- interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_ROTATOR>;
clock-names = "rotator";
iommus = <&sysmmu_rotator>;
@@ -647,7 +647,7 @@
gsc_0: video-scaler at 13e00000 {
compatible = "samsung,exynos5-gsc";
reg = <0x13e00000 0x1000>;
- interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_GSCL0>;
clock-names = "gscl";
power-domains = <&gsc_pd>;
@@ -657,7 +657,7 @@
gsc_1: video-scaler at 13e10000 {
compatible = "samsung,exynos5-gsc";
reg = <0x13e10000 0x1000>;
- interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_GSCL1>;
clock-names = "gscl";
power-domains = <&gsc_pd>;
@@ -667,7 +667,7 @@
jpeg_0: jpeg at 11F50000 {
compatible = "samsung,exynos5420-jpeg";
reg = <0x11F50000 0x1000>;
- interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "jpeg";
clocks = <&clock CLK_JPEG>;
iommus = <&sysmmu_jpeg0>;
@@ -676,7 +676,7 @@
jpeg_1: jpeg at 11F60000 {
compatible = "samsung,exynos5420-jpeg";
reg = <0x11F60000 0x1000>;
- interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "jpeg";
clocks = <&clock CLK_JPEG2>;
iommus = <&sysmmu_jpeg1>;
@@ -696,7 +696,7 @@
tmu_cpu0: tmu at 10060000 {
compatible = "samsung,exynos5420-tmu";
reg = <0x10060000 0x100>;
- interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -705,7 +705,7 @@
tmu_cpu1: tmu at 10064000 {
compatible = "samsung,exynos5420-tmu";
reg = <0x10064000 0x100>;
- interrupts = <0 183 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -714,7 +714,7 @@
tmu_cpu2: tmu at 10068000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x10068000 0x100>, <0x1006c000 0x4>;
- interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -723,7 +723,7 @@
tmu_cpu3: tmu at 1006c000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
- interrupts = <0 185 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -732,7 +732,7 @@
tmu_gpu: tmu at 100a0000 {
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x100a0000 0x100>, <0x10068000 0x4>;
- interrupts = <0 215 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
#include "exynos5420-tmu-sensor-conf.dtsi"
@@ -804,7 +804,7 @@
sysmmu_scaler1r: sysmmu at 0x12890000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x12890000 0x1000>;
- interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_MSCL1>, <&clock CLK_MSCL1>;
#iommu-cells = <0>;
@@ -813,7 +813,7 @@
sysmmu_scaler2r: sysmmu at 0x128A0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128A0000 0x1000>;
- interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_MSCL2>, <&clock CLK_MSCL2>;
#iommu-cells = <0>;
@@ -872,7 +872,7 @@
sysmmu_jpeg1: sysmmu at 0x11F20000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11F20000 0x1000>;
- interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "sysmmu", "master";
clocks = <&clock CLK_SMMU_JPEG2>, <&clock CLK_JPEG2>;
#iommu-cells = <0>;
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index a4ea018464fc..bc4954e69f7b 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -200,7 +200,7 @@
compatible = "snps,dwmac-3.70a", "snps,dwmac";
reg = <0x00230000 0x8000>;
interrupt-parent = <&gic>;
- interrupts = <GIC_SPI 31 4>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
phy-mode = "sgmii";
clocks = <&clock CLK_GMAC0>;
--
2.9.3
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags
2017-06-02 18:13 ` Krzysztof Kozlowski
@ 2017-06-07 19:05 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-07 19:05 UTC (permalink / raw)
To: Kukjin Kim, devicetree, linux-arm-kernel, linux-samsung-soc,
linux-kernel
Cc: Marek Szyprowski
On Fri, Jun 02, 2017 at 08:13:44PM +0200, Krzysztof Kozlowski wrote:
> Hi,
>
> Tested with comparing decompiled DTBs (dtx_diff). No differences.
>
For the record: applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags
@ 2017-06-07 19:05 ` Krzysztof Kozlowski
0 siblings, 0 replies; 9+ messages in thread
From: Krzysztof Kozlowski @ 2017-06-07 19:05 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jun 02, 2017 at 08:13:44PM +0200, Krzysztof Kozlowski wrote:
> Hi,
>
> Tested with comparing decompiled DTBs (dtx_diff). No differences.
>
For the record: applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2017-06-07 19:05 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-06-02 18:13 [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags Krzysztof Kozlowski
2017-06-02 18:13 ` Krzysztof Kozlowski
2017-06-02 18:13 ` [PATCH 1/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources Krzysztof Kozlowski
2017-06-02 18:13 ` Krzysztof Kozlowski
2017-06-02 18:13 ` Krzysztof Kozlowski
2017-06-02 18:13 ` [PATCH 2/2] ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties Krzysztof Kozlowski
2017-06-02 18:13 ` Krzysztof Kozlowski
2017-06-07 19:05 ` [PATCH 0/2] ARM: dts: exynos: Use human-friendly symbols for interrupt flags Krzysztof Kozlowski
2017-06-07 19:05 ` Krzysztof Kozlowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.