[PATCH v2 0/3] Add Keystone2 Remoteproc driver

[PATCH v2 0/3] Add Keystone2 Remoteproc driver

[Suman Anna]

Hi,

This is v2 of the patchset that adds the DT binding and the driver for
loading and booting the DSP devices present on various Keystone2 SoC families.
The current series supports the 66AK2H/K, 66AK2L and 66AK2E SoC families.
The DTS nodes will be posted separately once the binding is accepted,
and dependent patches from Loic are merged. See v1 cover-letter for details.

Main changes are in the binding to address various comments from 
Rob Herring. The driver is updated to construct firmware names based on
alias property. Exact changes are summarized in each patch.

v1:
http://marc.info/?t=149581802500004&r=1&w=2

regards
Suman

Andrew F. Davis (1):
  remoteproc/keystone: Ensure the DSPs are in reset in probe

Suman Anna (2):
  dt-bindings: remoteproc: Add Keystone DSP remoteproc binding
  remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 ++++++
 drivers/remoteproc/Kconfig                         |  13 +
 drivers/remoteproc/Makefile                        |   1 +
 drivers/remoteproc/keystone_remoteproc.c           | 525 +++++++++++++++++++++
 4 files changed, 674 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

-- 
2.12.0

[PATCH v2 0/3] Add Keystone2 Remoteproc driver

[Suman Anna]

Hi,

This is v2 of the patchset that adds the DT binding and the driver for
loading and booting the DSP devices present on various Keystone2 SoC families.
The current series supports the 66AK2H/K, 66AK2L and 66AK2E SoC families.
The DTS nodes will be posted separately once the binding is accepted,
and dependent patches from Loic are merged. See v1 cover-letter for details.

Main changes are in the binding to address various comments from 
Rob Herring. The driver is updated to construct firmware names based on
alias property. Exact changes are summarized in each patch.

v1:
http://marc.info/?t=149581802500004&r=1&w=2

regards
Suman

Andrew F. Davis (1):
  remoteproc/keystone: Ensure the DSPs are in reset in probe

Suman Anna (2):
  dt-bindings: remoteproc: Add Keystone DSP remoteproc binding
  remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 ++++++
 drivers/remoteproc/Kconfig                         |  13 +
 drivers/remoteproc/Makefile                        |   1 +
 drivers/remoteproc/keystone_remoteproc.c           | 525 +++++++++++++++++++++
 4 files changed, 674 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

-- 
2.12.0

[PATCH v2 0/3] Add Keystone2 Remoteproc driver

[Suman Anna]

Hi,

This is v2 of the patchset that adds the DT binding and the driver for
loading and booting the DSP devices present on various Keystone2 SoC families.
The current series supports the 66AK2H/K, 66AK2L and 66AK2E SoC families.
The DTS nodes will be posted separately once the binding is accepted,
and dependent patches from Loic are merged. See v1 cover-letter for details.

Main changes are in the binding to address various comments from 
Rob Herring. The driver is updated to construct firmware names based on
alias property. Exact changes are summarized in each patch.

v1:
http://marc.info/?t=149581802500004&r=1&w=2

regards
Suman

Andrew F. Davis (1):
  remoteproc/keystone: Ensure the DSPs are in reset in probe

Suman Anna (2):
  dt-bindings: remoteproc: Add Keystone DSP remoteproc binding
  remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 ++++++
 drivers/remoteproc/Kconfig                         |  13 +
 drivers/remoteproc/Makefile                        |   1 +
 drivers/remoteproc/keystone_remoteproc.c           | 525 +++++++++++++++++++++
 4 files changed, 674 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

-- 
2.12.0

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Suman Anna]

Add the device tree bindings document for the Texas Instrument's
Keystone 2 DSP remoteproc devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
---
v2 Changes:
 - Modified the patch title
 - Dropped unstable binding status
 - Dropped the 'label' property and replaced the device node description
   to use an alias
 - Renamed 'kick-gpio' to 'kick-gpios'
 - Updated the example
v1: https://patchwork.kernel.org/patch/9750839/

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
 1 file changed, 135 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
new file mode 100644
index 000000000000..162229244d14
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
@@ -0,0 +1,135 @@
+TI Keystone DSP devices
+=======================
+
+The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
+sub-systems that are used to offload some of the processor-intensive tasks or
+algorithms, for achieving various system level goals.
+
+These processor sub-systems usually contain additional sub-modules like L1
+and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
+a dedicated local power/sleep controller etc. The DSP processor core in
+Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
+
+DSP Device Node:
+================
+Each DSP Core sub-system is represented as a single DT node, and should also
+have an alias with the stem 'rproc' defined. Each node has a number of required
+or optional properties that enable the OS running on the host processor (ARM
+CorePac) to perform the device management of the remote processor and to
+communicate with the remote processor.
+
+Required properties:
+--------------------
+The following are the mandatory properties:
+
+- compatible:		Should be one of the following,
+			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
+			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
+			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
+
+- reg:			Should contain an entry for each value in 'reg-names'.
+			Each entry should have the memory region's start address
+			and the size of the region, the representation matching
+			the parent node's '#address-cells' and '#size-cells' values.
+
+- reg-names:		Should contain strings with the following names, each
+			representing a specific internal memory region, and
+			should be defined in this order,
+			     "l2sram", "l1pram", "l1dram"
+
+- clocks: 		Should contain the device's input clock, and should be
+			defined as per the bindings in,
+			Documentation/devicetree/bindings/clock/keystone-gate.txt
+
+- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
+			State Control node, and the register offset of the DSP
+			boot address register within that node's address space.
+
+- resets:		Should contain the phandle to the reset controller node
+			managing the resets for this device, and a reset
+			specifier. Please refer to the following reset bindings
+			for the reset argument specifier as per SoC,
+			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
+			    for 66AK2HK/66AK2L/66AK2E SoCs
+
+- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
+			IP node that is used by the ARM CorePac processor to
+			receive interrupts from the DSP remote processors. See
+			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
+			for details.
+
+- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
+			Each entry should have the interrupt source number used by
+			the remote processor to the host processor. The values should
+			follow the interrupt-specifier format as dictated by the
+			'interrupt-parent' node. The purpose of each is as per the
+			description in the 'interrupt-names' property.
+
+- interrupt-names:	Should contain strings with the following names, each
+			representing a specific interrupt,
+			    "vring" - interrupt for virtio based IPC
+			    "exception" - interrupt for exception notification
+
+- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
+			stack. This will be used to interrupt the remote processor.
+			The gpio device to be used is as per the bindings in,
+			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
+
+Optional properties:
+--------------------
+
+- memory-region:	phandle to the reserved memory node to be associated
+			with the remoteproc device. The reserved memory node
+			can be a CMA memory node, and should be defined as
+			per the bindings in
+			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
+
+
+Example:
+--------
+	/* 66AK2H/K DSP aliases */
+	aliases {
+		rproc0 = &dsp0;
+		rproc1 = &dsp1;
+		rproc2 = &dsp2;
+		rproc3 = &dsp3;
+		rproc4 = &dsp4;
+		rproc5 = &dsp5;
+		rproc6 = &dsp6;
+		rproc7 = &dsp7;
+	};
+
+	/* 66AK2H/K DSP memory node */
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_common_memory: dsp-common-memory@81f800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
+			reusable;
+		};
+	};
+
+	/* 66AK2H/K DSP node */
+	soc {
+		dsp0: dsp@10800000 {
+			compatible = "ti,k2hk-dsp";
+			reg = <0x10800000 0x00100000>,
+			      <0x10e00000 0x00008000>,
+			      <0x10f00000 0x00008000>;
+			reg-names = "l2sram", "l1pram", "l1dram";
+			label = "dsp0";
+			clocks = <&clkgem0>;
+			ti,syscon-dev = <&devctrl 0x40>;
+			resets = <&pscrst 0>;
+			interrupt-parent = <&kirq0>;
+			interrupts = <0 8>;
+			interrupt-names = "vring", "exception";
+			kick-gpios = <&dspgpio0 27 0>;
+			memory-region = <&dsp_common_memory>;
+		};
+
+	};
+
-- 
2.12.0

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Suman Anna]

Add the device tree bindings document for the Texas Instrument's
Keystone 2 DSP remoteproc devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
---
v2 Changes:
 - Modified the patch title
 - Dropped unstable binding status
 - Dropped the 'label' property and replaced the device node description
   to use an alias
 - Renamed 'kick-gpio' to 'kick-gpios'
 - Updated the example
v1: https://patchwork.kernel.org/patch/9750839/

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
 1 file changed, 135 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
new file mode 100644
index 000000000000..162229244d14
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
@@ -0,0 +1,135 @@
+TI Keystone DSP devices
+=======================
+
+The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
+sub-systems that are used to offload some of the processor-intensive tasks or
+algorithms, for achieving various system level goals.
+
+These processor sub-systems usually contain additional sub-modules like L1
+and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
+a dedicated local power/sleep controller etc. The DSP processor core in
+Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
+
+DSP Device Node:
+================
+Each DSP Core sub-system is represented as a single DT node, and should also
+have an alias with the stem 'rproc' defined. Each node has a number of required
+or optional properties that enable the OS running on the host processor (ARM
+CorePac) to perform the device management of the remote processor and to
+communicate with the remote processor.
+
+Required properties:
+--------------------
+The following are the mandatory properties:
+
+- compatible:		Should be one of the following,
+			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
+			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
+			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
+
+- reg:			Should contain an entry for each value in 'reg-names'.
+			Each entry should have the memory region's start address
+			and the size of the region, the representation matching
+			the parent node's '#address-cells' and '#size-cells' values.
+
+- reg-names:		Should contain strings with the following names, each
+			representing a specific internal memory region, and
+			should be defined in this order,
+			     "l2sram", "l1pram", "l1dram"
+
+- clocks: 		Should contain the device's input clock, and should be
+			defined as per the bindings in,
+			Documentation/devicetree/bindings/clock/keystone-gate.txt
+
+- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
+			State Control node, and the register offset of the DSP
+			boot address register within that node's address space.
+
+- resets:		Should contain the phandle to the reset controller node
+			managing the resets for this device, and a reset
+			specifier. Please refer to the following reset bindings
+			for the reset argument specifier as per SoC,
+			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
+			    for 66AK2HK/66AK2L/66AK2E SoCs
+
+- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
+			IP node that is used by the ARM CorePac processor to
+			receive interrupts from the DSP remote processors. See
+			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
+			for details.
+
+- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
+			Each entry should have the interrupt source number used by
+			the remote processor to the host processor. The values should
+			follow the interrupt-specifier format as dictated by the
+			'interrupt-parent' node. The purpose of each is as per the
+			description in the 'interrupt-names' property.
+
+- interrupt-names:	Should contain strings with the following names, each
+			representing a specific interrupt,
+			    "vring" - interrupt for virtio based IPC
+			    "exception" - interrupt for exception notification
+
+- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
+			stack. This will be used to interrupt the remote processor.
+			The gpio device to be used is as per the bindings in,
+			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
+
+Optional properties:
+--------------------
+
+- memory-region:	phandle to the reserved memory node to be associated
+			with the remoteproc device. The reserved memory node
+			can be a CMA memory node, and should be defined as
+			per the bindings in
+			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
+
+
+Example:
+--------
+	/* 66AK2H/K DSP aliases */
+	aliases {
+		rproc0 = &dsp0;
+		rproc1 = &dsp1;
+		rproc2 = &dsp2;
+		rproc3 = &dsp3;
+		rproc4 = &dsp4;
+		rproc5 = &dsp5;
+		rproc6 = &dsp6;
+		rproc7 = &dsp7;
+	};
+
+	/* 66AK2H/K DSP memory node */
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_common_memory: dsp-common-memory@81f800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
+			reusable;
+		};
+	};
+
+	/* 66AK2H/K DSP node */
+	soc {
+		dsp0: dsp@10800000 {
+			compatible = "ti,k2hk-dsp";
+			reg = <0x10800000 0x00100000>,
+			      <0x10e00000 0x00008000>,
+			      <0x10f00000 0x00008000>;
+			reg-names = "l2sram", "l1pram", "l1dram";
+			label = "dsp0";
+			clocks = <&clkgem0>;
+			ti,syscon-dev = <&devctrl 0x40>;
+			resets = <&pscrst 0>;
+			interrupt-parent = <&kirq0>;
+			interrupts = <0 8>;
+			interrupt-names = "vring", "exception";
+			kick-gpios = <&dspgpio0 27 0>;
+			memory-region = <&dsp_common_memory>;
+		};
+
+	};
+
-- 
2.12.0

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Suman Anna]

Add the device tree bindings document for the Texas Instrument's
Keystone 2 DSP remoteproc devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
---
v2 Changes:
 - Modified the patch title
 - Dropped unstable binding status
 - Dropped the 'label' property and replaced the device node description
   to use an alias
 - Renamed 'kick-gpio' to 'kick-gpios'
 - Updated the example
v1: https://patchwork.kernel.org/patch/9750839/

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
 1 file changed, 135 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
new file mode 100644
index 000000000000..162229244d14
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
@@ -0,0 +1,135 @@
+TI Keystone DSP devices
+=======================
+
+The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
+sub-systems that are used to offload some of the processor-intensive tasks or
+algorithms, for achieving various system level goals.
+
+These processor sub-systems usually contain additional sub-modules like L1
+and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
+a dedicated local power/sleep controller etc. The DSP processor core in
+Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
+
+DSP Device Node:
+================
+Each DSP Core sub-system is represented as a single DT node, and should also
+have an alias with the stem 'rproc' defined. Each node has a number of required
+or optional properties that enable the OS running on the host processor (ARM
+CorePac) to perform the device management of the remote processor and to
+communicate with the remote processor.
+
+Required properties:
+--------------------
+The following are the mandatory properties:
+
+- compatible:		Should be one of the following,
+			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
+			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
+			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
+
+- reg:			Should contain an entry for each value in 'reg-names'.
+			Each entry should have the memory region's start address
+			and the size of the region, the representation matching
+			the parent node's '#address-cells' and '#size-cells' values.
+
+- reg-names:		Should contain strings with the following names, each
+			representing a specific internal memory region, and
+			should be defined in this order,
+			     "l2sram", "l1pram", "l1dram"
+
+- clocks: 		Should contain the device's input clock, and should be
+			defined as per the bindings in,
+			Documentation/devicetree/bindings/clock/keystone-gate.txt
+
+- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
+			State Control node, and the register offset of the DSP
+			boot address register within that node's address space.
+
+- resets:		Should contain the phandle to the reset controller node
+			managing the resets for this device, and a reset
+			specifier. Please refer to the following reset bindings
+			for the reset argument specifier as per SoC,
+			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
+			    for 66AK2HK/66AK2L/66AK2E SoCs
+
+- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
+			IP node that is used by the ARM CorePac processor to
+			receive interrupts from the DSP remote processors. See
+			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
+			for details.
+
+- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
+			Each entry should have the interrupt source number used by
+			the remote processor to the host processor. The values should
+			follow the interrupt-specifier format as dictated by the
+			'interrupt-parent' node. The purpose of each is as per the
+			description in the 'interrupt-names' property.
+
+- interrupt-names:	Should contain strings with the following names, each
+			representing a specific interrupt,
+			    "vring" - interrupt for virtio based IPC
+			    "exception" - interrupt for exception notification
+
+- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
+			stack. This will be used to interrupt the remote processor.
+			The gpio device to be used is as per the bindings in,
+			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
+
+Optional properties:
+--------------------
+
+- memory-region:	phandle to the reserved memory node to be associated
+			with the remoteproc device. The reserved memory node
+			can be a CMA memory node, and should be defined as
+			per the bindings in
+			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
+
+
+Example:
+--------
+	/* 66AK2H/K DSP aliases */
+	aliases {
+		rproc0 = &dsp0;
+		rproc1 = &dsp1;
+		rproc2 = &dsp2;
+		rproc3 = &dsp3;
+		rproc4 = &dsp4;
+		rproc5 = &dsp5;
+		rproc6 = &dsp6;
+		rproc7 = &dsp7;
+	};
+
+	/* 66AK2H/K DSP memory node */
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_common_memory: dsp-common-memory@81f800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
+			reusable;
+		};
+	};
+
+	/* 66AK2H/K DSP node */
+	soc {
+		dsp0: dsp@10800000 {
+			compatible = "ti,k2hk-dsp";
+			reg = <0x10800000 0x00100000>,
+			      <0x10e00000 0x00008000>,
+			      <0x10f00000 0x00008000>;
+			reg-names = "l2sram", "l1pram", "l1dram";
+			label = "dsp0";
+			clocks = <&clkgem0>;
+			ti,syscon-dev = <&devctrl 0x40>;
+			resets = <&pscrst 0>;
+			interrupt-parent = <&kirq0>;
+			interrupts = <0 8>;
+			interrupt-names = "vring", "exception";
+			kick-gpios = <&dspgpio0 27 0>;
+			memory-region = <&dsp_common_memory>;
+		};
+
+	};
+
-- 
2.12.0

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Suman Anna]

Add the device tree bindings document for the Texas Instrument's
Keystone 2 DSP remoteproc devices.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
---
v2 Changes:
 - Modified the patch title
 - Dropped unstable binding status
 - Dropped the 'label' property and replaced the device node description
   to use an alias
 - Renamed 'kick-gpio' to 'kick-gpios'
 - Updated the example
v1: https://patchwork.kernel.org/patch/9750839/

 .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
 1 file changed, 135 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
new file mode 100644
index 000000000000..162229244d14
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
@@ -0,0 +1,135 @@
+TI Keystone DSP devices
+=======================
+
+The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
+sub-systems that are used to offload some of the processor-intensive tasks or
+algorithms, for achieving various system level goals.
+
+These processor sub-systems usually contain additional sub-modules like L1
+and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
+a dedicated local power/sleep controller etc. The DSP processor core in
+Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
+
+DSP Device Node:
+================
+Each DSP Core sub-system is represented as a single DT node, and should also
+have an alias with the stem 'rproc' defined. Each node has a number of required
+or optional properties that enable the OS running on the host processor (ARM
+CorePac) to perform the device management of the remote processor and to
+communicate with the remote processor.
+
+Required properties:
+--------------------
+The following are the mandatory properties:
+
+- compatible:		Should be one of the following,
+			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
+			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
+			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
+
+- reg:			Should contain an entry for each value in 'reg-names'.
+			Each entry should have the memory region's start address
+			and the size of the region, the representation matching
+			the parent node's '#address-cells' and '#size-cells' values.
+
+- reg-names:		Should contain strings with the following names, each
+			representing a specific internal memory region, and
+			should be defined in this order,
+			     "l2sram", "l1pram", "l1dram"
+
+- clocks: 		Should contain the device's input clock, and should be
+			defined as per the bindings in,
+			Documentation/devicetree/bindings/clock/keystone-gate.txt
+
+- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
+			State Control node, and the register offset of the DSP
+			boot address register within that node's address space.
+
+- resets:		Should contain the phandle to the reset controller node
+			managing the resets for this device, and a reset
+			specifier. Please refer to the following reset bindings
+			for the reset argument specifier as per SoC,
+			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
+			    for 66AK2HK/66AK2L/66AK2E SoCs
+
+- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
+			IP node that is used by the ARM CorePac processor to
+			receive interrupts from the DSP remote processors. See
+			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
+			for details.
+
+- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
+			Each entry should have the interrupt source number used by
+			the remote processor to the host processor. The values should
+			follow the interrupt-specifier format as dictated by the
+			'interrupt-parent' node. The purpose of each is as per the
+			description in the 'interrupt-names' property.
+
+- interrupt-names:	Should contain strings with the following names, each
+			representing a specific interrupt,
+			    "vring" - interrupt for virtio based IPC
+			    "exception" - interrupt for exception notification
+
+- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
+			stack. This will be used to interrupt the remote processor.
+			The gpio device to be used is as per the bindings in,
+			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
+
+Optional properties:
+--------------------
+
+- memory-region:	phandle to the reserved memory node to be associated
+			with the remoteproc device. The reserved memory node
+			can be a CMA memory node, and should be defined as
+			per the bindings in
+			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
+
+
+Example:
+--------
+	/* 66AK2H/K DSP aliases */
+	aliases {
+		rproc0 = &dsp0;
+		rproc1 = &dsp1;
+		rproc2 = &dsp2;
+		rproc3 = &dsp3;
+		rproc4 = &dsp4;
+		rproc5 = &dsp5;
+		rproc6 = &dsp6;
+		rproc7 = &dsp7;
+	};
+
+	/* 66AK2H/K DSP memory node */
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_common_memory: dsp-common-memory at 81f800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
+			reusable;
+		};
+	};
+
+	/* 66AK2H/K DSP node */
+	soc {
+		dsp0: dsp at 10800000 {
+			compatible = "ti,k2hk-dsp";
+			reg = <0x10800000 0x00100000>,
+			      <0x10e00000 0x00008000>,
+			      <0x10f00000 0x00008000>;
+			reg-names = "l2sram", "l1pram", "l1dram";
+			label = "dsp0";
+			clocks = <&clkgem0>;
+			ti,syscon-dev = <&devctrl 0x40>;
+			resets = <&pscrst 0>;
+			interrupt-parent = <&kirq0>;
+			interrupts = <0 8>;
+			interrupt-names = "vring", "exception";
+			kick-gpios = <&dspgpio0 27 0>;
+			memory-region = <&dsp_common_memory>;
+		};
+
+	};
+
-- 
2.12.0

[PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Suman Anna]

The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).

A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.

The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
---
v2:
 - Construct firmware name using an alias instead of the 'label' property
 - Rename kick-gpio to kick-gpios
v1: https://patchwork.kernel.org/patch/9750831/

 drivers/remoteproc/Kconfig               |  13 +
 drivers/remoteproc/Makefile              |   1 +
 drivers/remoteproc/keystone_remoteproc.c | 515 +++++++++++++++++++++++++++++++
 3 files changed, 529 insertions(+)
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index faad69a1a597..9839b35b6ab3 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -71,6 +71,19 @@ config DA8XX_REMOTEPROC
 	  It's safe to say n here if you're not interested in multimedia
 	  offloading.
 
+config KEYSTONE_REMOTEPROC
+	tristate "Keystone Remoteproc support"
+	depends on ARCH_KEYSTONE
+	depends on RESET_CONTROLLER
+	depends on REMOTEPROC
+	select RPMSG_VIRTIO
+	help
+	  Say Y here here to support Keystone remote processors (DSP)
+	  via the remote processor framework.
+
+	  It's safe to say N here if you're not interested in the Keystone
+	  DSPs or just want to use a bare minimum kernel.
+
 config QCOM_ADSP_PIL
 	tristate "Qualcomm ADSP Peripheral Image Loader"
 	depends on OF && ARCH_QCOM
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index ffc5e430df27..f1ce5fc8a2f3 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -11,6 +11,7 @@ remoteproc-y				+= remoteproc_elf_loader.o
 obj-$(CONFIG_OMAP_REMOTEPROC)		+= omap_remoteproc.o
 obj-$(CONFIG_WKUP_M3_RPROC)		+= wkup_m3_rproc.o
 obj-$(CONFIG_DA8XX_REMOTEPROC)		+= da8xx_remoteproc.o
+obj-$(CONFIG_KEYSTONE_REMOTEPROC)	+= keystone_remoteproc.o
 obj-$(CONFIG_QCOM_ADSP_PIL)		+= qcom_adsp_pil.o
 obj-$(CONFIG_QCOM_RPROC_COMMON)		+= qcom_common.o
 obj-$(CONFIG_QCOM_Q6V5_PIL)		+= qcom_q6v5_pil.o
diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
new file mode 100644
index 000000000000..6e09ef76f7c7
--- /dev/null
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -0,0 +1,515 @@
+/*
+ * TI Keystone DSP remoteproc driver
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/workqueue.h>
+#include <linux/of_address.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+
+#include "remoteproc_internal.h"
+
+#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
+
+/**
+ * struct keystone_rproc_mem - internal memory structure
+ * @cpu_addr: MPU virtual address of the memory region
+ * @bus_addr: Bus address used to access the memory region
+ * @dev_addr: Device address of the memory region from DSP view
+ * @size: Size of the memory region
+ */
+struct keystone_rproc_mem {
+	void __iomem *cpu_addr;
+	phys_addr_t bus_addr;
+	u32 dev_addr;
+	size_t size;
+};
+
+/**
+ * struct keystone_rproc - keystone remote processor driver structure
+ * @dev: cached device pointer
+ * @rproc: remoteproc device handle
+ * @mem: internal memory regions data
+ * @num_mems: number of internal memory regions
+ * @dev_ctrl: device control regmap handle
+ * @reset: reset control handle
+ * @boot_offset: boot register offset in @dev_ctrl regmap
+ * @irq_ring: irq entry for vring
+ * @irq_fault: irq entry for exception
+ * @kick_gpio: gpio used for virtio kicks
+ * @workqueue: workqueue for processing virtio interrupts
+ */
+struct keystone_rproc {
+	struct device *dev;
+	struct rproc *rproc;
+	struct keystone_rproc_mem *mem;
+	int num_mems;
+	struct regmap *dev_ctrl;
+	struct reset_control *reset;
+	u32 boot_offset;
+	int irq_ring;
+	int irq_fault;
+	int kick_gpio;
+	struct work_struct workqueue;
+};
+
+/* Put the DSP processor into reset */
+static void keystone_rproc_dsp_reset(struct keystone_rproc *ksproc)
+{
+	reset_control_assert(ksproc->reset);
+}
+
+/* Configure the boot address and boot the DSP processor */
+static int keystone_rproc_dsp_boot(struct keystone_rproc *ksproc, u32 boot_addr)
+{
+	int ret;
+
+	if (boot_addr & (SZ_1K - 1)) {
+		dev_err(ksproc->dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n",
+			boot_addr);
+		return -EINVAL;
+	}
+
+	ret = regmap_write(ksproc->dev_ctrl, ksproc->boot_offset, boot_addr);
+	if (ret) {
+		dev_err(ksproc->dev, "regmap_write of boot address failed, status = %d\n",
+			ret);
+		return ret;
+	}
+
+	reset_control_deassert(ksproc->reset);
+
+	return 0;
+}
+
+/*
+ * Process the remoteproc exceptions
+ *
+ * The exception reporting on Keystone DSP remote processors is very simple
+ * compared to the equivalent processors on the OMAP family, it is notified
+ * through a software-designed specific interrupt source in the IPC interrupt
+ * generation register.
+ *
+ * This function just invokes the rproc_report_crash to report the exception
+ * to the remoteproc driver core, to trigger a recovery.
+ */
+static irqreturn_t keystone_rproc_exception_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	rproc_report_crash(ksproc->rproc, RPROC_FATAL_ERROR);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Main virtqueue message workqueue function
+ *
+ * This function is executed upon scheduling of the keystone remoteproc
+ * driver's workqueue. The workqueue is scheduled by the vring ISR handler.
+ *
+ * There is no payload message indicating the virtqueue index as is the
+ * case with mailbox-based implementations on OMAP family. As such, this
+ * handler processes both the Tx and Rx virtqueue indices on every invocation.
+ * The rproc_vq_interrupt function can detect if there are new unprocessed
+ * messages or not (returns IRQ_NONE vs IRQ_HANDLED), but there is no need
+ * to check for these return values. The index 0 triggering will process all
+ * pending Rx buffers, and the index 1 triggering will process all newly
+ * available Tx buffers and will wakeup any potentially blocked senders.
+ *
+ * NOTE:
+ * 1. A payload could be added by using some of the source bits in the
+ *    IPC interrupt generation registers, but this would need additional
+ *    changes to the overall IPC stack, and currently there are no benefits
+ *    of adapting that approach.
+ * 2. The current logic is based on an inherent design assumption of supporting
+ *    only 2 vrings, but this can be changed if needed.
+ */
+static void handle_event(struct work_struct *work)
+{
+	struct keystone_rproc *ksproc =
+		container_of(work, struct keystone_rproc, workqueue);
+
+	rproc_vq_interrupt(ksproc->rproc, 0);
+	rproc_vq_interrupt(ksproc->rproc, 1);
+}
+
+/*
+ * Interrupt handler for processing vring kicks from remote processor
+ */
+static irqreturn_t keystone_rproc_vring_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	schedule_work(&ksproc->workqueue);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Power up the DSP remote processor.
+ *
+ * This function will be invoked only after the firmware for this rproc
+ * was loaded, parsed successfully, and all of its resource requirements
+ * were met.
+ */
+static int keystone_rproc_start(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	int ret;
+
+	INIT_WORK(&ksproc->workqueue, handle_event);
+
+	ret = request_irq(ksproc->irq_ring, keystone_rproc_vring_interrupt, 0,
+			  dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable vring interrupt, ret = %d\n",
+			ret);
+		goto out;
+	}
+
+	ret = request_irq(ksproc->irq_fault, keystone_rproc_exception_interrupt,
+			  0, dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable exception interrupt, ret = %d\n",
+			ret);
+		goto free_vring_irq;
+	}
+
+	ret = keystone_rproc_dsp_boot(ksproc, rproc->bootaddr);
+	if (ret)
+		goto free_exc_irq;
+
+	return 0;
+
+free_exc_irq:
+	free_irq(ksproc->irq_fault, ksproc);
+free_vring_irq:
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+out:
+	return ret;
+}
+
+/*
+ * Stop the DSP remote processor.
+ *
+ * This function puts the DSP processor into reset, and finishes processing
+ * of any pending messages.
+ */
+static int keystone_rproc_stop(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	keystone_rproc_dsp_reset(ksproc);
+	free_irq(ksproc->irq_fault, ksproc);
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+
+	return 0;
+}
+
+/*
+ * Kick the remote processor to notify about pending unprocessed messages.
+ * The vqid usage is not used and is inconsequential, as the kick is performed
+ * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
+ * the remote processor is expected to process both its Tx and Rx virtqueues.
+ */
+static void keystone_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	if (WARN_ON(ksproc->kick_gpio < 0))
+		return;
+
+	gpio_set_value(ksproc->kick_gpio, 1);
+}
+
+/*
+ * Custom function to translate a DSP device address (internal RAMs only) to a
+ * kernel virtual address.  The DSPs can access their RAMs at either an internal
+ * address visible only from a DSP, or at the SoC-level bus address. Both these
+ * addresses need to be looked through for translation. The translated addresses
+ * can be used either by the remoteproc core for loading (when using kernel
+ * remoteproc loader), or by any rpmsg bus drivers.
+ */
+static void *keystone_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	void __iomem *va = NULL;
+	phys_addr_t bus_addr;
+	u32 dev_addr, offset;
+	size_t size;
+	int i;
+
+	if (len <= 0)
+		return NULL;
+
+	for (i = 0; i < ksproc->num_mems; i++) {
+		bus_addr = ksproc->mem[i].bus_addr;
+		dev_addr = ksproc->mem[i].dev_addr;
+		size = ksproc->mem[i].size;
+
+		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
+			/* handle DSP-view addresses */
+			if ((da >= dev_addr) &&
+			    ((da + len) <= (dev_addr + size))) {
+				offset = da - dev_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		} else {
+			/* handle SoC-view addresses */
+			if ((da >= bus_addr) &&
+			    (da + len) <= (bus_addr + size)) {
+				offset = da - bus_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		}
+	}
+
+	return (__force void *)va;
+}
+
+static const struct rproc_ops keystone_rproc_ops = {
+	.start		= keystone_rproc_start,
+	.stop		= keystone_rproc_stop,
+	.kick		= keystone_rproc_kick,
+	.da_to_va	= keystone_rproc_da_to_va,
+};
+
+static int keystone_rproc_of_get_memories(struct platform_device *pdev,
+					  struct keystone_rproc *ksproc)
+{
+	static const char * const mem_names[] = {"l2sram", "l1pram", "l1dram"};
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int num_mems = 0;
+	int i;
+
+	num_mems = ARRAY_SIZE(mem_names);
+	ksproc->mem = devm_kcalloc(ksproc->dev, num_mems,
+				   sizeof(*ksproc->mem), GFP_KERNEL);
+	if (!ksproc->mem)
+		return -ENOMEM;
+
+	for (i = 0; i < num_mems; i++) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   mem_names[i]);
+		ksproc->mem[i].cpu_addr = devm_ioremap_resource(dev, res);
+		if (IS_ERR(ksproc->mem[i].cpu_addr)) {
+			dev_err(dev, "failed to parse and map %s memory\n",
+				mem_names[i]);
+			return PTR_ERR(ksproc->mem[i].cpu_addr);
+		}
+		ksproc->mem[i].bus_addr = res->start;
+		ksproc->mem[i].dev_addr =
+				res->start & KEYSTONE_RPROC_LOCAL_ADDRESS_MASK;
+		ksproc->mem[i].size = resource_size(res);
+
+		/* zero out memories to start in a pristine state */
+		memset((__force void *)ksproc->mem[i].cpu_addr, 0,
+		       ksproc->mem[i].size);
+	}
+	ksproc->num_mems = num_mems;
+
+	return 0;
+}
+
+static int keystone_rproc_of_get_dev_syscon(struct platform_device *pdev,
+					    struct keystone_rproc *ksproc)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	if (!of_property_read_bool(np, "ti,syscon-dev")) {
+		dev_err(dev, "ti,syscon-dev property is absent\n");
+		return -EINVAL;
+	}
+
+	ksproc->dev_ctrl =
+		syscon_regmap_lookup_by_phandle(np, "ti,syscon-dev");
+	if (IS_ERR(ksproc->dev_ctrl)) {
+		ret = PTR_ERR(ksproc->dev_ctrl);
+		return ret;
+	}
+
+	if (of_property_read_u32_index(np, "ti,syscon-dev", 1,
+				       &ksproc->boot_offset)) {
+		dev_err(dev, "couldn't read the boot register offset\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int keystone_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct keystone_rproc *ksproc;
+	struct rproc *rproc;
+	int dsp_id;
+	char *fw_name = NULL;
+	char *template = "keystone-dsp%d-fw";
+	int name_len = 0;
+	int ret = 0;
+
+	if (!np) {
+		dev_err(dev, "only DT-based devices are supported\n");
+		return -ENODEV;
+	}
+
+	dsp_id = of_alias_get_id(np, "rproc");
+	if (dsp_id < 0) {
+		dev_warn(dev, "device does not have an alias id\n");
+		return dsp_id;
+	}
+
+	/* construct a custom default fw name - subject to change in future */
+	name_len = strlen(template); /* assuming a single digit alias */
+	fw_name = devm_kzalloc(dev, name_len, GFP_KERNEL);
+	if (!fw_name)
+		return -ENOMEM;
+	snprintf(fw_name, name_len, template, dsp_id);
+
+	rproc = rproc_alloc(dev, dev_name(dev), &keystone_rproc_ops, fw_name,
+			    sizeof(*ksproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->has_iommu = false;
+	ksproc = rproc->priv;
+	ksproc->rproc = rproc;
+	ksproc->dev = dev;
+
+	ret = keystone_rproc_of_get_dev_syscon(pdev, ksproc);
+	if (ret)
+		goto free_rproc;
+
+	ksproc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(ksproc->reset)) {
+		ret = PTR_ERR(ksproc->reset);
+		goto free_rproc;
+	}
+
+	/* enable clock for accessing DSP internal memories */
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable clock, status = %d\n", ret);
+		pm_runtime_put_noidle(dev);
+		goto disable_rpm;
+	}
+
+	ret = keystone_rproc_of_get_memories(pdev, ksproc);
+	if (ret)
+		goto disable_clk;
+
+	ksproc->irq_ring = platform_get_irq_byname(pdev, "vring");
+	if (ksproc->irq_ring < 0) {
+		ret = ksproc->irq_ring;
+		dev_err(dev, "failed to get vring interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->irq_fault = platform_get_irq_byname(pdev, "exception");
+	if (ksproc->irq_fault < 0) {
+		ret = ksproc->irq_fault;
+		dev_err(dev, "failed to get exception interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->kick_gpio = of_get_named_gpio_flags(np, "kick-gpios", 0, NULL);
+	if (ksproc->kick_gpio < 0) {
+		ret = ksproc->kick_gpio;
+		dev_err(dev, "failed to get gpio for virtio kicks, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	if (of_reserved_mem_device_init(dev))
+		dev_warn(dev, "device does not have specific CMA pool\n");
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
+			ret);
+		goto release_mem;
+	}
+
+	platform_set_drvdata(pdev, ksproc);
+
+	return 0;
+
+release_mem:
+	of_reserved_mem_device_release(dev);
+disable_clk:
+	pm_runtime_put_sync(dev);
+disable_rpm:
+	pm_runtime_disable(dev);
+free_rproc:
+	rproc_free(rproc);
+	return ret;
+}
+
+static int keystone_rproc_remove(struct platform_device *pdev)
+{
+	struct keystone_rproc *ksproc = platform_get_drvdata(pdev);
+
+	rproc_del(ksproc->rproc);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	rproc_free(ksproc->rproc);
+	of_reserved_mem_device_release(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id keystone_rproc_of_match[] = {
+	{ .compatible = "ti,k2hk-dsp", },
+	{ .compatible = "ti,k2l-dsp", },
+	{ .compatible = "ti,k2e-dsp", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, keystone_rproc_of_match);
+
+static struct platform_driver keystone_rproc_driver = {
+	.probe	= keystone_rproc_probe,
+	.remove	= keystone_rproc_remove,
+	.driver	= {
+		.name = "keystone-rproc",
+		.of_match_table = keystone_rproc_of_match,
+	},
+};
+
+module_platform_driver(keystone_rproc_driver);
+
+MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI Keystone DSP Remoteproc driver");
-- 
2.12.0

[PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Suman Anna]

The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).

A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.

The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
---
v2:
 - Construct firmware name using an alias instead of the 'label' property
 - Rename kick-gpio to kick-gpios
v1: https://patchwork.kernel.org/patch/9750831/

 drivers/remoteproc/Kconfig               |  13 +
 drivers/remoteproc/Makefile              |   1 +
 drivers/remoteproc/keystone_remoteproc.c | 515 +++++++++++++++++++++++++++++++
 3 files changed, 529 insertions(+)
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index faad69a1a597..9839b35b6ab3 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -71,6 +71,19 @@ config DA8XX_REMOTEPROC
 	  It's safe to say n here if you're not interested in multimedia
 	  offloading.
 
+config KEYSTONE_REMOTEPROC
+	tristate "Keystone Remoteproc support"
+	depends on ARCH_KEYSTONE
+	depends on RESET_CONTROLLER
+	depends on REMOTEPROC
+	select RPMSG_VIRTIO
+	help
+	  Say Y here here to support Keystone remote processors (DSP)
+	  via the remote processor framework.
+
+	  It's safe to say N here if you're not interested in the Keystone
+	  DSPs or just want to use a bare minimum kernel.
+
 config QCOM_ADSP_PIL
 	tristate "Qualcomm ADSP Peripheral Image Loader"
 	depends on OF && ARCH_QCOM
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index ffc5e430df27..f1ce5fc8a2f3 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -11,6 +11,7 @@ remoteproc-y				+= remoteproc_elf_loader.o
 obj-$(CONFIG_OMAP_REMOTEPROC)		+= omap_remoteproc.o
 obj-$(CONFIG_WKUP_M3_RPROC)		+= wkup_m3_rproc.o
 obj-$(CONFIG_DA8XX_REMOTEPROC)		+= da8xx_remoteproc.o
+obj-$(CONFIG_KEYSTONE_REMOTEPROC)	+= keystone_remoteproc.o
 obj-$(CONFIG_QCOM_ADSP_PIL)		+= qcom_adsp_pil.o
 obj-$(CONFIG_QCOM_RPROC_COMMON)		+= qcom_common.o
 obj-$(CONFIG_QCOM_Q6V5_PIL)		+= qcom_q6v5_pil.o
diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
new file mode 100644
index 000000000000..6e09ef76f7c7
--- /dev/null
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -0,0 +1,515 @@
+/*
+ * TI Keystone DSP remoteproc driver
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/workqueue.h>
+#include <linux/of_address.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+
+#include "remoteproc_internal.h"
+
+#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
+
+/**
+ * struct keystone_rproc_mem - internal memory structure
+ * @cpu_addr: MPU virtual address of the memory region
+ * @bus_addr: Bus address used to access the memory region
+ * @dev_addr: Device address of the memory region from DSP view
+ * @size: Size of the memory region
+ */
+struct keystone_rproc_mem {
+	void __iomem *cpu_addr;
+	phys_addr_t bus_addr;
+	u32 dev_addr;
+	size_t size;
+};
+
+/**
+ * struct keystone_rproc - keystone remote processor driver structure
+ * @dev: cached device pointer
+ * @rproc: remoteproc device handle
+ * @mem: internal memory regions data
+ * @num_mems: number of internal memory regions
+ * @dev_ctrl: device control regmap handle
+ * @reset: reset control handle
+ * @boot_offset: boot register offset in @dev_ctrl regmap
+ * @irq_ring: irq entry for vring
+ * @irq_fault: irq entry for exception
+ * @kick_gpio: gpio used for virtio kicks
+ * @workqueue: workqueue for processing virtio interrupts
+ */
+struct keystone_rproc {
+	struct device *dev;
+	struct rproc *rproc;
+	struct keystone_rproc_mem *mem;
+	int num_mems;
+	struct regmap *dev_ctrl;
+	struct reset_control *reset;
+	u32 boot_offset;
+	int irq_ring;
+	int irq_fault;
+	int kick_gpio;
+	struct work_struct workqueue;
+};
+
+/* Put the DSP processor into reset */
+static void keystone_rproc_dsp_reset(struct keystone_rproc *ksproc)
+{
+	reset_control_assert(ksproc->reset);
+}
+
+/* Configure the boot address and boot the DSP processor */
+static int keystone_rproc_dsp_boot(struct keystone_rproc *ksproc, u32 boot_addr)
+{
+	int ret;
+
+	if (boot_addr & (SZ_1K - 1)) {
+		dev_err(ksproc->dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n",
+			boot_addr);
+		return -EINVAL;
+	}
+
+	ret = regmap_write(ksproc->dev_ctrl, ksproc->boot_offset, boot_addr);
+	if (ret) {
+		dev_err(ksproc->dev, "regmap_write of boot address failed, status = %d\n",
+			ret);
+		return ret;
+	}
+
+	reset_control_deassert(ksproc->reset);
+
+	return 0;
+}
+
+/*
+ * Process the remoteproc exceptions
+ *
+ * The exception reporting on Keystone DSP remote processors is very simple
+ * compared to the equivalent processors on the OMAP family, it is notified
+ * through a software-designed specific interrupt source in the IPC interrupt
+ * generation register.
+ *
+ * This function just invokes the rproc_report_crash to report the exception
+ * to the remoteproc driver core, to trigger a recovery.
+ */
+static irqreturn_t keystone_rproc_exception_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	rproc_report_crash(ksproc->rproc, RPROC_FATAL_ERROR);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Main virtqueue message workqueue function
+ *
+ * This function is executed upon scheduling of the keystone remoteproc
+ * driver's workqueue. The workqueue is scheduled by the vring ISR handler.
+ *
+ * There is no payload message indicating the virtqueue index as is the
+ * case with mailbox-based implementations on OMAP family. As such, this
+ * handler processes both the Tx and Rx virtqueue indices on every invocation.
+ * The rproc_vq_interrupt function can detect if there are new unprocessed
+ * messages or not (returns IRQ_NONE vs IRQ_HANDLED), but there is no need
+ * to check for these return values. The index 0 triggering will process all
+ * pending Rx buffers, and the index 1 triggering will process all newly
+ * available Tx buffers and will wakeup any potentially blocked senders.
+ *
+ * NOTE:
+ * 1. A payload could be added by using some of the source bits in the
+ *    IPC interrupt generation registers, but this would need additional
+ *    changes to the overall IPC stack, and currently there are no benefits
+ *    of adapting that approach.
+ * 2. The current logic is based on an inherent design assumption of supporting
+ *    only 2 vrings, but this can be changed if needed.
+ */
+static void handle_event(struct work_struct *work)
+{
+	struct keystone_rproc *ksproc =
+		container_of(work, struct keystone_rproc, workqueue);
+
+	rproc_vq_interrupt(ksproc->rproc, 0);
+	rproc_vq_interrupt(ksproc->rproc, 1);
+}
+
+/*
+ * Interrupt handler for processing vring kicks from remote processor
+ */
+static irqreturn_t keystone_rproc_vring_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	schedule_work(&ksproc->workqueue);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Power up the DSP remote processor.
+ *
+ * This function will be invoked only after the firmware for this rproc
+ * was loaded, parsed successfully, and all of its resource requirements
+ * were met.
+ */
+static int keystone_rproc_start(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	int ret;
+
+	INIT_WORK(&ksproc->workqueue, handle_event);
+
+	ret = request_irq(ksproc->irq_ring, keystone_rproc_vring_interrupt, 0,
+			  dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable vring interrupt, ret = %d\n",
+			ret);
+		goto out;
+	}
+
+	ret = request_irq(ksproc->irq_fault, keystone_rproc_exception_interrupt,
+			  0, dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable exception interrupt, ret = %d\n",
+			ret);
+		goto free_vring_irq;
+	}
+
+	ret = keystone_rproc_dsp_boot(ksproc, rproc->bootaddr);
+	if (ret)
+		goto free_exc_irq;
+
+	return 0;
+
+free_exc_irq:
+	free_irq(ksproc->irq_fault, ksproc);
+free_vring_irq:
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+out:
+	return ret;
+}
+
+/*
+ * Stop the DSP remote processor.
+ *
+ * This function puts the DSP processor into reset, and finishes processing
+ * of any pending messages.
+ */
+static int keystone_rproc_stop(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	keystone_rproc_dsp_reset(ksproc);
+	free_irq(ksproc->irq_fault, ksproc);
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+
+	return 0;
+}
+
+/*
+ * Kick the remote processor to notify about pending unprocessed messages.
+ * The vqid usage is not used and is inconsequential, as the kick is performed
+ * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
+ * the remote processor is expected to process both its Tx and Rx virtqueues.
+ */
+static void keystone_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	if (WARN_ON(ksproc->kick_gpio < 0))
+		return;
+
+	gpio_set_value(ksproc->kick_gpio, 1);
+}
+
+/*
+ * Custom function to translate a DSP device address (internal RAMs only) to a
+ * kernel virtual address.  The DSPs can access their RAMs at either an internal
+ * address visible only from a DSP, or at the SoC-level bus address. Both these
+ * addresses need to be looked through for translation. The translated addresses
+ * can be used either by the remoteproc core for loading (when using kernel
+ * remoteproc loader), or by any rpmsg bus drivers.
+ */
+static void *keystone_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	void __iomem *va = NULL;
+	phys_addr_t bus_addr;
+	u32 dev_addr, offset;
+	size_t size;
+	int i;
+
+	if (len <= 0)
+		return NULL;
+
+	for (i = 0; i < ksproc->num_mems; i++) {
+		bus_addr = ksproc->mem[i].bus_addr;
+		dev_addr = ksproc->mem[i].dev_addr;
+		size = ksproc->mem[i].size;
+
+		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
+			/* handle DSP-view addresses */
+			if ((da >= dev_addr) &&
+			    ((da + len) <= (dev_addr + size))) {
+				offset = da - dev_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		} else {
+			/* handle SoC-view addresses */
+			if ((da >= bus_addr) &&
+			    (da + len) <= (bus_addr + size)) {
+				offset = da - bus_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		}
+	}
+
+	return (__force void *)va;
+}
+
+static const struct rproc_ops keystone_rproc_ops = {
+	.start		= keystone_rproc_start,
+	.stop		= keystone_rproc_stop,
+	.kick		= keystone_rproc_kick,
+	.da_to_va	= keystone_rproc_da_to_va,
+};
+
+static int keystone_rproc_of_get_memories(struct platform_device *pdev,
+					  struct keystone_rproc *ksproc)
+{
+	static const char * const mem_names[] = {"l2sram", "l1pram", "l1dram"};
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int num_mems = 0;
+	int i;
+
+	num_mems = ARRAY_SIZE(mem_names);
+	ksproc->mem = devm_kcalloc(ksproc->dev, num_mems,
+				   sizeof(*ksproc->mem), GFP_KERNEL);
+	if (!ksproc->mem)
+		return -ENOMEM;
+
+	for (i = 0; i < num_mems; i++) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   mem_names[i]);
+		ksproc->mem[i].cpu_addr = devm_ioremap_resource(dev, res);
+		if (IS_ERR(ksproc->mem[i].cpu_addr)) {
+			dev_err(dev, "failed to parse and map %s memory\n",
+				mem_names[i]);
+			return PTR_ERR(ksproc->mem[i].cpu_addr);
+		}
+		ksproc->mem[i].bus_addr = res->start;
+		ksproc->mem[i].dev_addr =
+				res->start & KEYSTONE_RPROC_LOCAL_ADDRESS_MASK;
+		ksproc->mem[i].size = resource_size(res);
+
+		/* zero out memories to start in a pristine state */
+		memset((__force void *)ksproc->mem[i].cpu_addr, 0,
+		       ksproc->mem[i].size);
+	}
+	ksproc->num_mems = num_mems;
+
+	return 0;
+}
+
+static int keystone_rproc_of_get_dev_syscon(struct platform_device *pdev,
+					    struct keystone_rproc *ksproc)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	if (!of_property_read_bool(np, "ti,syscon-dev")) {
+		dev_err(dev, "ti,syscon-dev property is absent\n");
+		return -EINVAL;
+	}
+
+	ksproc->dev_ctrl =
+		syscon_regmap_lookup_by_phandle(np, "ti,syscon-dev");
+	if (IS_ERR(ksproc->dev_ctrl)) {
+		ret = PTR_ERR(ksproc->dev_ctrl);
+		return ret;
+	}
+
+	if (of_property_read_u32_index(np, "ti,syscon-dev", 1,
+				       &ksproc->boot_offset)) {
+		dev_err(dev, "couldn't read the boot register offset\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int keystone_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct keystone_rproc *ksproc;
+	struct rproc *rproc;
+	int dsp_id;
+	char *fw_name = NULL;
+	char *template = "keystone-dsp%d-fw";
+	int name_len = 0;
+	int ret = 0;
+
+	if (!np) {
+		dev_err(dev, "only DT-based devices are supported\n");
+		return -ENODEV;
+	}
+
+	dsp_id = of_alias_get_id(np, "rproc");
+	if (dsp_id < 0) {
+		dev_warn(dev, "device does not have an alias id\n");
+		return dsp_id;
+	}
+
+	/* construct a custom default fw name - subject to change in future */
+	name_len = strlen(template); /* assuming a single digit alias */
+	fw_name = devm_kzalloc(dev, name_len, GFP_KERNEL);
+	if (!fw_name)
+		return -ENOMEM;
+	snprintf(fw_name, name_len, template, dsp_id);
+
+	rproc = rproc_alloc(dev, dev_name(dev), &keystone_rproc_ops, fw_name,
+			    sizeof(*ksproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->has_iommu = false;
+	ksproc = rproc->priv;
+	ksproc->rproc = rproc;
+	ksproc->dev = dev;
+
+	ret = keystone_rproc_of_get_dev_syscon(pdev, ksproc);
+	if (ret)
+		goto free_rproc;
+
+	ksproc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(ksproc->reset)) {
+		ret = PTR_ERR(ksproc->reset);
+		goto free_rproc;
+	}
+
+	/* enable clock for accessing DSP internal memories */
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable clock, status = %d\n", ret);
+		pm_runtime_put_noidle(dev);
+		goto disable_rpm;
+	}
+
+	ret = keystone_rproc_of_get_memories(pdev, ksproc);
+	if (ret)
+		goto disable_clk;
+
+	ksproc->irq_ring = platform_get_irq_byname(pdev, "vring");
+	if (ksproc->irq_ring < 0) {
+		ret = ksproc->irq_ring;
+		dev_err(dev, "failed to get vring interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->irq_fault = platform_get_irq_byname(pdev, "exception");
+	if (ksproc->irq_fault < 0) {
+		ret = ksproc->irq_fault;
+		dev_err(dev, "failed to get exception interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->kick_gpio = of_get_named_gpio_flags(np, "kick-gpios", 0, NULL);
+	if (ksproc->kick_gpio < 0) {
+		ret = ksproc->kick_gpio;
+		dev_err(dev, "failed to get gpio for virtio kicks, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	if (of_reserved_mem_device_init(dev))
+		dev_warn(dev, "device does not have specific CMA pool\n");
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
+			ret);
+		goto release_mem;
+	}
+
+	platform_set_drvdata(pdev, ksproc);
+
+	return 0;
+
+release_mem:
+	of_reserved_mem_device_release(dev);
+disable_clk:
+	pm_runtime_put_sync(dev);
+disable_rpm:
+	pm_runtime_disable(dev);
+free_rproc:
+	rproc_free(rproc);
+	return ret;
+}
+
+static int keystone_rproc_remove(struct platform_device *pdev)
+{
+	struct keystone_rproc *ksproc = platform_get_drvdata(pdev);
+
+	rproc_del(ksproc->rproc);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	rproc_free(ksproc->rproc);
+	of_reserved_mem_device_release(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id keystone_rproc_of_match[] = {
+	{ .compatible = "ti,k2hk-dsp", },
+	{ .compatible = "ti,k2l-dsp", },
+	{ .compatible = "ti,k2e-dsp", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, keystone_rproc_of_match);
+
+static struct platform_driver keystone_rproc_driver = {
+	.probe	= keystone_rproc_probe,
+	.remove	= keystone_rproc_remove,
+	.driver	= {
+		.name = "keystone-rproc",
+		.of_match_table = keystone_rproc_of_match,
+	},
+};
+
+module_platform_driver(keystone_rproc_driver);
+
+MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI Keystone DSP Remoteproc driver");
-- 
2.12.0

[PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Suman Anna]

The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).

A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.

The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
---
v2:
 - Construct firmware name using an alias instead of the 'label' property
 - Rename kick-gpio to kick-gpios
v1: https://patchwork.kernel.org/patch/9750831/

 drivers/remoteproc/Kconfig               |  13 +
 drivers/remoteproc/Makefile              |   1 +
 drivers/remoteproc/keystone_remoteproc.c | 515 +++++++++++++++++++++++++++++++
 3 files changed, 529 insertions(+)
 create mode 100644 drivers/remoteproc/keystone_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index faad69a1a597..9839b35b6ab3 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -71,6 +71,19 @@ config DA8XX_REMOTEPROC
 	  It's safe to say n here if you're not interested in multimedia
 	  offloading.
 
+config KEYSTONE_REMOTEPROC
+	tristate "Keystone Remoteproc support"
+	depends on ARCH_KEYSTONE
+	depends on RESET_CONTROLLER
+	depends on REMOTEPROC
+	select RPMSG_VIRTIO
+	help
+	  Say Y here here to support Keystone remote processors (DSP)
+	  via the remote processor framework.
+
+	  It's safe to say N here if you're not interested in the Keystone
+	  DSPs or just want to use a bare minimum kernel.
+
 config QCOM_ADSP_PIL
 	tristate "Qualcomm ADSP Peripheral Image Loader"
 	depends on OF && ARCH_QCOM
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index ffc5e430df27..f1ce5fc8a2f3 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -11,6 +11,7 @@ remoteproc-y				+= remoteproc_elf_loader.o
 obj-$(CONFIG_OMAP_REMOTEPROC)		+= omap_remoteproc.o
 obj-$(CONFIG_WKUP_M3_RPROC)		+= wkup_m3_rproc.o
 obj-$(CONFIG_DA8XX_REMOTEPROC)		+= da8xx_remoteproc.o
+obj-$(CONFIG_KEYSTONE_REMOTEPROC)	+= keystone_remoteproc.o
 obj-$(CONFIG_QCOM_ADSP_PIL)		+= qcom_adsp_pil.o
 obj-$(CONFIG_QCOM_RPROC_COMMON)		+= qcom_common.o
 obj-$(CONFIG_QCOM_Q6V5_PIL)		+= qcom_q6v5_pil.o
diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
new file mode 100644
index 000000000000..6e09ef76f7c7
--- /dev/null
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -0,0 +1,515 @@
+/*
+ * TI Keystone DSP remoteproc driver
+ *
+ * Copyright (C) 2015-2017 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/workqueue.h>
+#include <linux/of_address.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/of_gpio.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+
+#include "remoteproc_internal.h"
+
+#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
+
+/**
+ * struct keystone_rproc_mem - internal memory structure
+ * @cpu_addr: MPU virtual address of the memory region
+ * @bus_addr: Bus address used to access the memory region
+ * @dev_addr: Device address of the memory region from DSP view
+ * @size: Size of the memory region
+ */
+struct keystone_rproc_mem {
+	void __iomem *cpu_addr;
+	phys_addr_t bus_addr;
+	u32 dev_addr;
+	size_t size;
+};
+
+/**
+ * struct keystone_rproc - keystone remote processor driver structure
+ * @dev: cached device pointer
+ * @rproc: remoteproc device handle
+ * @mem: internal memory regions data
+ * @num_mems: number of internal memory regions
+ * @dev_ctrl: device control regmap handle
+ * @reset: reset control handle
+ * @boot_offset: boot register offset in @dev_ctrl regmap
+ * @irq_ring: irq entry for vring
+ * @irq_fault: irq entry for exception
+ * @kick_gpio: gpio used for virtio kicks
+ * @workqueue: workqueue for processing virtio interrupts
+ */
+struct keystone_rproc {
+	struct device *dev;
+	struct rproc *rproc;
+	struct keystone_rproc_mem *mem;
+	int num_mems;
+	struct regmap *dev_ctrl;
+	struct reset_control *reset;
+	u32 boot_offset;
+	int irq_ring;
+	int irq_fault;
+	int kick_gpio;
+	struct work_struct workqueue;
+};
+
+/* Put the DSP processor into reset */
+static void keystone_rproc_dsp_reset(struct keystone_rproc *ksproc)
+{
+	reset_control_assert(ksproc->reset);
+}
+
+/* Configure the boot address and boot the DSP processor */
+static int keystone_rproc_dsp_boot(struct keystone_rproc *ksproc, u32 boot_addr)
+{
+	int ret;
+
+	if (boot_addr & (SZ_1K - 1)) {
+		dev_err(ksproc->dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n",
+			boot_addr);
+		return -EINVAL;
+	}
+
+	ret = regmap_write(ksproc->dev_ctrl, ksproc->boot_offset, boot_addr);
+	if (ret) {
+		dev_err(ksproc->dev, "regmap_write of boot address failed, status = %d\n",
+			ret);
+		return ret;
+	}
+
+	reset_control_deassert(ksproc->reset);
+
+	return 0;
+}
+
+/*
+ * Process the remoteproc exceptions
+ *
+ * The exception reporting on Keystone DSP remote processors is very simple
+ * compared to the equivalent processors on the OMAP family, it is notified
+ * through a software-designed specific interrupt source in the IPC interrupt
+ * generation register.
+ *
+ * This function just invokes the rproc_report_crash to report the exception
+ * to the remoteproc driver core, to trigger a recovery.
+ */
+static irqreturn_t keystone_rproc_exception_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	rproc_report_crash(ksproc->rproc, RPROC_FATAL_ERROR);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Main virtqueue message workqueue function
+ *
+ * This function is executed upon scheduling of the keystone remoteproc
+ * driver's workqueue. The workqueue is scheduled by the vring ISR handler.
+ *
+ * There is no payload message indicating the virtqueue index as is the
+ * case with mailbox-based implementations on OMAP family. As such, this
+ * handler processes both the Tx and Rx virtqueue indices on every invocation.
+ * The rproc_vq_interrupt function can detect if there are new unprocessed
+ * messages or not (returns IRQ_NONE vs IRQ_HANDLED), but there is no need
+ * to check for these return values. The index 0 triggering will process all
+ * pending Rx buffers, and the index 1 triggering will process all newly
+ * available Tx buffers and will wakeup any potentially blocked senders.
+ *
+ * NOTE:
+ * 1. A payload could be added by using some of the source bits in the
+ *    IPC interrupt generation registers, but this would need additional
+ *    changes to the overall IPC stack, and currently there are no benefits
+ *    of adapting that approach.
+ * 2. The current logic is based on an inherent design assumption of supporting
+ *    only 2 vrings, but this can be changed if needed.
+ */
+static void handle_event(struct work_struct *work)
+{
+	struct keystone_rproc *ksproc =
+		container_of(work, struct keystone_rproc, workqueue);
+
+	rproc_vq_interrupt(ksproc->rproc, 0);
+	rproc_vq_interrupt(ksproc->rproc, 1);
+}
+
+/*
+ * Interrupt handler for processing vring kicks from remote processor
+ */
+static irqreturn_t keystone_rproc_vring_interrupt(int irq, void *dev_id)
+{
+	struct keystone_rproc *ksproc = dev_id;
+
+	schedule_work(&ksproc->workqueue);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Power up the DSP remote processor.
+ *
+ * This function will be invoked only after the firmware for this rproc
+ * was loaded, parsed successfully, and all of its resource requirements
+ * were met.
+ */
+static int keystone_rproc_start(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	int ret;
+
+	INIT_WORK(&ksproc->workqueue, handle_event);
+
+	ret = request_irq(ksproc->irq_ring, keystone_rproc_vring_interrupt, 0,
+			  dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable vring interrupt, ret = %d\n",
+			ret);
+		goto out;
+	}
+
+	ret = request_irq(ksproc->irq_fault, keystone_rproc_exception_interrupt,
+			  0, dev_name(ksproc->dev), ksproc);
+	if (ret) {
+		dev_err(ksproc->dev, "failed to enable exception interrupt, ret = %d\n",
+			ret);
+		goto free_vring_irq;
+	}
+
+	ret = keystone_rproc_dsp_boot(ksproc, rproc->bootaddr);
+	if (ret)
+		goto free_exc_irq;
+
+	return 0;
+
+free_exc_irq:
+	free_irq(ksproc->irq_fault, ksproc);
+free_vring_irq:
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+out:
+	return ret;
+}
+
+/*
+ * Stop the DSP remote processor.
+ *
+ * This function puts the DSP processor into reset, and finishes processing
+ * of any pending messages.
+ */
+static int keystone_rproc_stop(struct rproc *rproc)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	keystone_rproc_dsp_reset(ksproc);
+	free_irq(ksproc->irq_fault, ksproc);
+	free_irq(ksproc->irq_ring, ksproc);
+	flush_work(&ksproc->workqueue);
+
+	return 0;
+}
+
+/*
+ * Kick the remote processor to notify about pending unprocessed messages.
+ * The vqid usage is not used and is inconsequential, as the kick is performed
+ * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
+ * the remote processor is expected to process both its Tx and Rx virtqueues.
+ */
+static void keystone_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+
+	if (WARN_ON(ksproc->kick_gpio < 0))
+		return;
+
+	gpio_set_value(ksproc->kick_gpio, 1);
+}
+
+/*
+ * Custom function to translate a DSP device address (internal RAMs only) to a
+ * kernel virtual address.  The DSPs can access their RAMs at either an internal
+ * address visible only from a DSP, or at the SoC-level bus address. Both these
+ * addresses need to be looked through for translation. The translated addresses
+ * can be used either by the remoteproc core for loading (when using kernel
+ * remoteproc loader), or by any rpmsg bus drivers.
+ */
+static void *keystone_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
+{
+	struct keystone_rproc *ksproc = rproc->priv;
+	void __iomem *va = NULL;
+	phys_addr_t bus_addr;
+	u32 dev_addr, offset;
+	size_t size;
+	int i;
+
+	if (len <= 0)
+		return NULL;
+
+	for (i = 0; i < ksproc->num_mems; i++) {
+		bus_addr = ksproc->mem[i].bus_addr;
+		dev_addr = ksproc->mem[i].dev_addr;
+		size = ksproc->mem[i].size;
+
+		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
+			/* handle DSP-view addresses */
+			if ((da >= dev_addr) &&
+			    ((da + len) <= (dev_addr + size))) {
+				offset = da - dev_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		} else {
+			/* handle SoC-view addresses */
+			if ((da >= bus_addr) &&
+			    (da + len) <= (bus_addr + size)) {
+				offset = da - bus_addr;
+				va = ksproc->mem[i].cpu_addr + offset;
+				break;
+			}
+		}
+	}
+
+	return (__force void *)va;
+}
+
+static const struct rproc_ops keystone_rproc_ops = {
+	.start		= keystone_rproc_start,
+	.stop		= keystone_rproc_stop,
+	.kick		= keystone_rproc_kick,
+	.da_to_va	= keystone_rproc_da_to_va,
+};
+
+static int keystone_rproc_of_get_memories(struct platform_device *pdev,
+					  struct keystone_rproc *ksproc)
+{
+	static const char * const mem_names[] = {"l2sram", "l1pram", "l1dram"};
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int num_mems = 0;
+	int i;
+
+	num_mems = ARRAY_SIZE(mem_names);
+	ksproc->mem = devm_kcalloc(ksproc->dev, num_mems,
+				   sizeof(*ksproc->mem), GFP_KERNEL);
+	if (!ksproc->mem)
+		return -ENOMEM;
+
+	for (i = 0; i < num_mems; i++) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   mem_names[i]);
+		ksproc->mem[i].cpu_addr = devm_ioremap_resource(dev, res);
+		if (IS_ERR(ksproc->mem[i].cpu_addr)) {
+			dev_err(dev, "failed to parse and map %s memory\n",
+				mem_names[i]);
+			return PTR_ERR(ksproc->mem[i].cpu_addr);
+		}
+		ksproc->mem[i].bus_addr = res->start;
+		ksproc->mem[i].dev_addr =
+				res->start & KEYSTONE_RPROC_LOCAL_ADDRESS_MASK;
+		ksproc->mem[i].size = resource_size(res);
+
+		/* zero out memories to start in a pristine state */
+		memset((__force void *)ksproc->mem[i].cpu_addr, 0,
+		       ksproc->mem[i].size);
+	}
+	ksproc->num_mems = num_mems;
+
+	return 0;
+}
+
+static int keystone_rproc_of_get_dev_syscon(struct platform_device *pdev,
+					    struct keystone_rproc *ksproc)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	if (!of_property_read_bool(np, "ti,syscon-dev")) {
+		dev_err(dev, "ti,syscon-dev property is absent\n");
+		return -EINVAL;
+	}
+
+	ksproc->dev_ctrl =
+		syscon_regmap_lookup_by_phandle(np, "ti,syscon-dev");
+	if (IS_ERR(ksproc->dev_ctrl)) {
+		ret = PTR_ERR(ksproc->dev_ctrl);
+		return ret;
+	}
+
+	if (of_property_read_u32_index(np, "ti,syscon-dev", 1,
+				       &ksproc->boot_offset)) {
+		dev_err(dev, "couldn't read the boot register offset\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int keystone_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct keystone_rproc *ksproc;
+	struct rproc *rproc;
+	int dsp_id;
+	char *fw_name = NULL;
+	char *template = "keystone-dsp%d-fw";
+	int name_len = 0;
+	int ret = 0;
+
+	if (!np) {
+		dev_err(dev, "only DT-based devices are supported\n");
+		return -ENODEV;
+	}
+
+	dsp_id = of_alias_get_id(np, "rproc");
+	if (dsp_id < 0) {
+		dev_warn(dev, "device does not have an alias id\n");
+		return dsp_id;
+	}
+
+	/* construct a custom default fw name - subject to change in future */
+	name_len = strlen(template); /* assuming a single digit alias */
+	fw_name = devm_kzalloc(dev, name_len, GFP_KERNEL);
+	if (!fw_name)
+		return -ENOMEM;
+	snprintf(fw_name, name_len, template, dsp_id);
+
+	rproc = rproc_alloc(dev, dev_name(dev), &keystone_rproc_ops, fw_name,
+			    sizeof(*ksproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->has_iommu = false;
+	ksproc = rproc->priv;
+	ksproc->rproc = rproc;
+	ksproc->dev = dev;
+
+	ret = keystone_rproc_of_get_dev_syscon(pdev, ksproc);
+	if (ret)
+		goto free_rproc;
+
+	ksproc->reset = devm_reset_control_get(dev, NULL);
+	if (IS_ERR(ksproc->reset)) {
+		ret = PTR_ERR(ksproc->reset);
+		goto free_rproc;
+	}
+
+	/* enable clock for accessing DSP internal memories */
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable clock, status = %d\n", ret);
+		pm_runtime_put_noidle(dev);
+		goto disable_rpm;
+	}
+
+	ret = keystone_rproc_of_get_memories(pdev, ksproc);
+	if (ret)
+		goto disable_clk;
+
+	ksproc->irq_ring = platform_get_irq_byname(pdev, "vring");
+	if (ksproc->irq_ring < 0) {
+		ret = ksproc->irq_ring;
+		dev_err(dev, "failed to get vring interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->irq_fault = platform_get_irq_byname(pdev, "exception");
+	if (ksproc->irq_fault < 0) {
+		ret = ksproc->irq_fault;
+		dev_err(dev, "failed to get exception interrupt, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	ksproc->kick_gpio = of_get_named_gpio_flags(np, "kick-gpios", 0, NULL);
+	if (ksproc->kick_gpio < 0) {
+		ret = ksproc->kick_gpio;
+		dev_err(dev, "failed to get gpio for virtio kicks, status = %d\n",
+			ret);
+		goto disable_clk;
+	}
+
+	if (of_reserved_mem_device_init(dev))
+		dev_warn(dev, "device does not have specific CMA pool\n");
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
+			ret);
+		goto release_mem;
+	}
+
+	platform_set_drvdata(pdev, ksproc);
+
+	return 0;
+
+release_mem:
+	of_reserved_mem_device_release(dev);
+disable_clk:
+	pm_runtime_put_sync(dev);
+disable_rpm:
+	pm_runtime_disable(dev);
+free_rproc:
+	rproc_free(rproc);
+	return ret;
+}
+
+static int keystone_rproc_remove(struct platform_device *pdev)
+{
+	struct keystone_rproc *ksproc = platform_get_drvdata(pdev);
+
+	rproc_del(ksproc->rproc);
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	rproc_free(ksproc->rproc);
+	of_reserved_mem_device_release(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id keystone_rproc_of_match[] = {
+	{ .compatible = "ti,k2hk-dsp", },
+	{ .compatible = "ti,k2l-dsp", },
+	{ .compatible = "ti,k2e-dsp", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, keystone_rproc_of_match);
+
+static struct platform_driver keystone_rproc_driver = {
+	.probe	= keystone_rproc_probe,
+	.remove	= keystone_rproc_remove,
+	.driver	= {
+		.name = "keystone-rproc",
+		.of_match_table = keystone_rproc_of_match,
+	},
+};
+
+module_platform_driver(keystone_rproc_driver);
+
+MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI Keystone DSP Remoteproc driver");
-- 
2.12.0

[PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Suman Anna]

From: "Andrew F. Davis" <afd@ti.com>

The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
---
v2: No code changes

 drivers/remoteproc/keystone_remoteproc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
index 6e09ef76f7c7..5f776bfd674a 100644
--- a/drivers/remoteproc/keystone_remoteproc.c
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -456,6 +456,16 @@ static int keystone_rproc_probe(struct platform_device *pdev)
 	if (of_reserved_mem_device_init(dev))
 		dev_warn(dev, "device does not have specific CMA pool\n");
 
+	/* ensure the DSP is in reset before loading firmware */
+	ret = reset_control_status(ksproc->reset);
+	if (ret < 0) {
+		dev_err(dev, "failed to get reset status, status = %d\n", ret);
+		goto release_mem;
+	} else if (ret == 0) {
+		WARN(1, "device is not in reset\n");
+		keystone_rproc_dsp_reset(ksproc);
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
-- 
2.12.0

[PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Suman Anna]

From: "Andrew F. Davis" <afd@ti.com>

The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
---
v2: No code changes

 drivers/remoteproc/keystone_remoteproc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
index 6e09ef76f7c7..5f776bfd674a 100644
--- a/drivers/remoteproc/keystone_remoteproc.c
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -456,6 +456,16 @@ static int keystone_rproc_probe(struct platform_device *pdev)
 	if (of_reserved_mem_device_init(dev))
 		dev_warn(dev, "device does not have specific CMA pool\n");
 
+	/* ensure the DSP is in reset before loading firmware */
+	ret = reset_control_status(ksproc->reset);
+	if (ret < 0) {
+		dev_err(dev, "failed to get reset status, status = %d\n", ret);
+		goto release_mem;
+	} else if (ret == 0) {
+		WARN(1, "device is not in reset\n");
+		keystone_rproc_dsp_reset(ksproc);
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
-- 
2.12.0

[PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Suman Anna]

From: "Andrew F. Davis" <afd@ti.com>

The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
---
v2: No code changes

 drivers/remoteproc/keystone_remoteproc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
index 6e09ef76f7c7..5f776bfd674a 100644
--- a/drivers/remoteproc/keystone_remoteproc.c
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -456,6 +456,16 @@ static int keystone_rproc_probe(struct platform_device *pdev)
 	if (of_reserved_mem_device_init(dev))
 		dev_warn(dev, "device does not have specific CMA pool\n");
 
+	/* ensure the DSP is in reset before loading firmware */
+	ret = reset_control_status(ksproc->reset);
+	if (ret < 0) {
+		dev_err(dev, "failed to get reset status, status = %d\n", ret);
+		goto release_mem;
+	} else if (ret == 0) {
+		WARN(1, "device is not in reset\n");
+		keystone_rproc_dsp_reset(ksproc);
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
-- 
2.12.0

[PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Suman Anna]

From: "Andrew F. Davis" <afd@ti.com>

The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.

Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna at ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
---
v2: No code changes

 drivers/remoteproc/keystone_remoteproc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/remoteproc/keystone_remoteproc.c b/drivers/remoteproc/keystone_remoteproc.c
index 6e09ef76f7c7..5f776bfd674a 100644
--- a/drivers/remoteproc/keystone_remoteproc.c
+++ b/drivers/remoteproc/keystone_remoteproc.c
@@ -456,6 +456,16 @@ static int keystone_rproc_probe(struct platform_device *pdev)
 	if (of_reserved_mem_device_init(dev))
 		dev_warn(dev, "device does not have specific CMA pool\n");
 
+	/* ensure the DSP is in reset before loading firmware */
+	ret = reset_control_status(ksproc->reset);
+	if (ret < 0) {
+		dev_err(dev, "failed to get reset status, status = %d\n", ret);
+		goto release_mem;
+	} else if (ret == 0) {
+		WARN(1, "device is not in reset\n");
+		keystone_rproc_dsp_reset(ksproc);
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "failed to add register device with remoteproc core, status = %d\n",
-- 
2.12.0

Re: [PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Rob Herring]

On Wed, Jun 07, 2017 at 07:24:45PM -0500, Suman Anna wrote:
> Add the device tree bindings document for the Texas Instrument's
> Keystone 2 DSP remoteproc devices.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> ---
> v2 Changes:
>  - Modified the patch title
>  - Dropped unstable binding status
>  - Dropped the 'label' property and replaced the device node description
>    to use an alias
>  - Renamed 'kick-gpio' to 'kick-gpios'
>  - Updated the example
> v1: https://patchwork.kernel.org/patch/9750839/
> 
>  .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
>  1 file changed, 135 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> 
> diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> new file mode 100644
> index 000000000000..162229244d14
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> @@ -0,0 +1,135 @@
> +TI Keystone DSP devices
> +=======================
> +
> +The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
> +sub-systems that are used to offload some of the processor-intensive tasks or
> +algorithms, for achieving various system level goals.
> +
> +These processor sub-systems usually contain additional sub-modules like L1
> +and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
> +a dedicated local power/sleep controller etc. The DSP processor core in
> +Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
> +
> +DSP Device Node:
> +================
> +Each DSP Core sub-system is represented as a single DT node, and should also
> +have an alias with the stem 'rproc' defined. Each node has a number of required
> +or optional properties that enable the OS running on the host processor (ARM
> +CorePac) to perform the device management of the remote processor and to
> +communicate with the remote processor.
> +
> +Required properties:
> +--------------------
> +The following are the mandatory properties:
> +
> +- compatible:		Should be one of the following,
> +			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
> +			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
> +			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
> +
> +- reg:			Should contain an entry for each value in 'reg-names'.
> +			Each entry should have the memory region's start address
> +			and the size of the region, the representation matching
> +			the parent node's '#address-cells' and '#size-cells' values.
> +
> +- reg-names:		Should contain strings with the following names, each
> +			representing a specific internal memory region, and
> +			should be defined in this order,
> +			     "l2sram", "l1pram", "l1dram"
> +
> +- clocks: 		Should contain the device's input clock, and should be
> +			defined as per the bindings in,
> +			Documentation/devicetree/bindings/clock/keystone-gate.txt
> +
> +- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
> +			State Control node, and the register offset of the DSP
> +			boot address register within that node's address space.
> +
> +- resets:		Should contain the phandle to the reset controller node
> +			managing the resets for this device, and a reset
> +			specifier. Please refer to the following reset bindings
> +			for the reset argument specifier as per SoC,
> +			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
> +			    for 66AK2HK/66AK2L/66AK2E SoCs
> +
> +- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
> +			IP node that is used by the ARM CorePac processor to
> +			receive interrupts from the DSP remote processors. See
> +			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
> +			for details.
> +
> +- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
> +			Each entry should have the interrupt source number used by
> +			the remote processor to the host processor. The values should
> +			follow the interrupt-specifier format as dictated by the
> +			'interrupt-parent' node. The purpose of each is as per the
> +			description in the 'interrupt-names' property.
> +
> +- interrupt-names:	Should contain strings with the following names, each
> +			representing a specific interrupt,
> +			    "vring" - interrupt for virtio based IPC
> +			    "exception" - interrupt for exception notification
> +
> +- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
> +			stack. This will be used to interrupt the remote processor.
> +			The gpio device to be used is as per the bindings in,
> +			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
> +
> +Optional properties:
> +--------------------
> +
> +- memory-region:	phandle to the reserved memory node to be associated
> +			with the remoteproc device. The reserved memory node
> +			can be a CMA memory node, and should be defined as
> +			per the bindings in
> +			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
> +
> +
> +Example:
> +--------
> +	/* 66AK2H/K DSP aliases */
> +	aliases {
> +		rproc0 = &dsp0;
> +		rproc1 = &dsp1;
> +		rproc2 = &dsp2;
> +		rproc3 = &dsp3;
> +		rproc4 = &dsp4;
> +		rproc5 = &dsp5;
> +		rproc6 = &dsp6;
> +		rproc7 = &dsp7;
> +	};
> +
> +	/* 66AK2H/K DSP memory node */
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		dsp_common_memory: dsp-common-memory@81f800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
> +			reusable;
> +		};
> +	};
> +
> +	/* 66AK2H/K DSP node */
> +	soc {
> +		dsp0: dsp@10800000 {
> +			compatible = "ti,k2hk-dsp";
> +			reg = <0x10800000 0x00100000>,
> +			      <0x10e00000 0x00008000>,
> +			      <0x10f00000 0x00008000>;
> +			reg-names = "l2sram", "l1pram", "l1dram";
> +			label = "dsp0";

Need to drop this. With that,

Acked-by: Rob Herring <robh@kernel.org>

> +			clocks = <&clkgem0>;
> +			ti,syscon-dev = <&devctrl 0x40>;
> +			resets = <&pscrst 0>;
> +			interrupt-parent = <&kirq0>;
> +			interrupts = <0 8>;
> +			interrupt-names = "vring", "exception";
> +			kick-gpios = <&dspgpio0 27 0>;
> +			memory-region = <&dsp_common_memory>;
> +		};
> +
> +	};
> +
> -- 
> 2.12.0
> 

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Rob Herring]

On Wed, Jun 07, 2017 at 07:24:45PM -0500, Suman Anna wrote:
> Add the device tree bindings document for the Texas Instrument's
> Keystone 2 DSP remoteproc devices.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> ---
> v2 Changes:
>  - Modified the patch title
>  - Dropped unstable binding status
>  - Dropped the 'label' property and replaced the device node description
>    to use an alias
>  - Renamed 'kick-gpio' to 'kick-gpios'
>  - Updated the example
> v1: https://patchwork.kernel.org/patch/9750839/
> 
>  .../bindings/remoteproc/ti,keystone-rproc.txt      | 135 +++++++++++++++++++++
>  1 file changed, 135 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> 
> diff --git a/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> new file mode 100644
> index 000000000000..162229244d14
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/ti,keystone-rproc.txt
> @@ -0,0 +1,135 @@
> +TI Keystone DSP devices
> +=======================
> +
> +The TI Keystone 2 family of SoCs usually have one or more (upto 8) TI DSP Core
> +sub-systems that are used to offload some of the processor-intensive tasks or
> +algorithms, for achieving various system level goals.
> +
> +These processor sub-systems usually contain additional sub-modules like L1
> +and/or L2 caches/SRAMs, an Interrupt Controller, an external memory controller,
> +a dedicated local power/sleep controller etc. The DSP processor core in
> +Keystone 2 SoCs is usually a TMS320C66x CorePac processor.
> +
> +DSP Device Node:
> +================
> +Each DSP Core sub-system is represented as a single DT node, and should also
> +have an alias with the stem 'rproc' defined. Each node has a number of required
> +or optional properties that enable the OS running on the host processor (ARM
> +CorePac) to perform the device management of the remote processor and to
> +communicate with the remote processor.
> +
> +Required properties:
> +--------------------
> +The following are the mandatory properties:
> +
> +- compatible:		Should be one of the following,
> +			    "ti,k2hk-dsp" for DSPs on Keystone 2 66AK2H/K SoCs
> +			    "ti,k2l-dsp" for DSPs on Keystone 2 66AK2L SoCs
> +			    "ti,k2e-dsp" for DSPs on Keystone 2 66AK2E SoCs
> +
> +- reg:			Should contain an entry for each value in 'reg-names'.
> +			Each entry should have the memory region's start address
> +			and the size of the region, the representation matching
> +			the parent node's '#address-cells' and '#size-cells' values.
> +
> +- reg-names:		Should contain strings with the following names, each
> +			representing a specific internal memory region, and
> +			should be defined in this order,
> +			     "l2sram", "l1pram", "l1dram"
> +
> +- clocks: 		Should contain the device's input clock, and should be
> +			defined as per the bindings in,
> +			Documentation/devicetree/bindings/clock/keystone-gate.txt
> +
> +- ti,syscon-dev:	Should be a pair of the phandle to the Keystone Device
> +			State Control node, and the register offset of the DSP
> +			boot address register within that node's address space.
> +
> +- resets:		Should contain the phandle to the reset controller node
> +			managing the resets for this device, and a reset
> +			specifier. Please refer to the following reset bindings
> +			for the reset argument specifier as per SoC,
> +			Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
> +			    for 66AK2HK/66AK2L/66AK2E SoCs
> +
> +- interrupt-parent:	Should contain a phandle to the Keystone 2 IRQ controller
> +			IP node that is used by the ARM CorePac processor to
> +			receive interrupts from the DSP remote processors. See
> +			Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
> +			for details.
> +
> +- interrupts: 		Should contain an entry for each value in 'interrupt-names'.
> +			Each entry should have the interrupt source number used by
> +			the remote processor to the host processor. The values should
> +			follow the interrupt-specifier format as dictated by the
> +			'interrupt-parent' node. The purpose of each is as per the
> +			description in the 'interrupt-names' property.
> +
> +- interrupt-names:	Should contain strings with the following names, each
> +			representing a specific interrupt,
> +			    "vring" - interrupt for virtio based IPC
> +			    "exception" - interrupt for exception notification
> +
> +- kick-gpios: 		Should specify the gpio device needed for the virtio IPC
> +			stack. This will be used to interrupt the remote processor.
> +			The gpio device to be used is as per the bindings in,
> +			Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
> +
> +Optional properties:
> +--------------------
> +
> +- memory-region:	phandle to the reserved memory node to be associated
> +			with the remoteproc device. The reserved memory node
> +			can be a CMA memory node, and should be defined as
> +			per the bindings in
> +			Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
> +
> +
> +Example:
> +--------
> +	/* 66AK2H/K DSP aliases */
> +	aliases {
> +		rproc0 = &dsp0;
> +		rproc1 = &dsp1;
> +		rproc2 = &dsp2;
> +		rproc3 = &dsp3;
> +		rproc4 = &dsp4;
> +		rproc5 = &dsp5;
> +		rproc6 = &dsp6;
> +		rproc7 = &dsp7;
> +	};
> +
> +	/* 66AK2H/K DSP memory node */
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		dsp_common_memory: dsp-common-memory at 81f800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00000008 0x1f800000 0x00000000 0x800000>;
> +			reusable;
> +		};
> +	};
> +
> +	/* 66AK2H/K DSP node */
> +	soc {
> +		dsp0: dsp at 10800000 {
> +			compatible = "ti,k2hk-dsp";
> +			reg = <0x10800000 0x00100000>,
> +			      <0x10e00000 0x00008000>,
> +			      <0x10f00000 0x00008000>;
> +			reg-names = "l2sram", "l1pram", "l1dram";
> +			label = "dsp0";

Need to drop this. With that,

Acked-by: Rob Herring <robh@kernel.org>

> +			clocks = <&clkgem0>;
> +			ti,syscon-dev = <&devctrl 0x40>;
> +			resets = <&pscrst 0>;
> +			interrupt-parent = <&kirq0>;
> +			interrupts = <0 8>;
> +			interrupt-names = "vring", "exception";
> +			kick-gpios = <&dspgpio0 27 0>;
> +			memory-region = <&dsp_common_memory>;
> +		};
> +
> +	};
> +
> -- 
> 2.12.0
> 

Re: [PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Santosh Shilimkar]

6/7/2017 5:24 PM, Suman Anna wrote:
> The Texas Instrument's Keystone 2 family of SoCs has 1 or more
> TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
> a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
> that can be configured and partitioned as either RAM and/or Cache,
> and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
> External Memory Controller (EMC), Extended Memory Controller (XMC)
> with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
> Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
> Controller (PDC).
> 
> A new remoteproc module is added to perform the device management of
> these DSP devices. The driver expects the firmware names to be of the
> form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
> uses the standard remoteproc core ELF loader. The support is limited
> to images only using the DSP internal memories at the moment. This
> remoteproc driver is also designed to work with virtio, and uses the
> IPC Generation registers for performing the virtio signalling and
> getting notified of exceptions.
> 
> The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
> SoCs.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> ---

Acked-by: Santosh Shilimkar <ssantosh@kernel.org>

Re: [PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Santosh Shilimkar]

6/7/2017 5:24 PM, Suman Anna wrote:
> The Texas Instrument's Keystone 2 family of SoCs has 1 or more
> TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
> a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
> that can be configured and partitioned as either RAM and/or Cache,
> and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
> External Memory Controller (EMC), Extended Memory Controller (XMC)
> with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
> Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
> Controller (PDC).
> 
> A new remoteproc module is added to perform the device management of
> these DSP devices. The driver expects the firmware names to be of the
> form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
> uses the standard remoteproc core ELF loader. The support is limited
> to images only using the DSP internal memories at the moment. This
> remoteproc driver is also designed to work with virtio, and uses the
> IPC Generation registers for performing the virtio signalling and
> getting notified of exceptions.
> 
> The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
> SoCs.
> 
> Signed-off-by: Suman Anna <s-anna-l0cyMroinI0@public.gmane.org>
> Signed-off-by: Sam Nelson <sam.nelson-l0cyMroinI0@public.gmane.org>
> Signed-off-by: Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org>
> ---

Acked-by: Santosh Shilimkar <ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 2/3] remoteproc/keystone: Add a remoteproc driver for Keystone 2 DSPs

[Santosh Shilimkar]

6/7/2017 5:24 PM, Suman Anna wrote:
> The Texas Instrument's Keystone 2 family of SoCs has 1 or more
> TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
> a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
> that can be configured and partitioned as either RAM and/or Cache,
> and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
> External Memory Controller (EMC), Extended Memory Controller (XMC)
> with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
> Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
> Controller (PDC).
> 
> A new remoteproc module is added to perform the device management of
> these DSP devices. The driver expects the firmware names to be of the
> form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
> uses the standard remoteproc core ELF loader. The support is limited
> to images only using the DSP internal memories at the moment. This
> remoteproc driver is also designed to work with virtio, and uses the
> IPC Generation registers for performing the virtio signalling and
> getting notified of exceptions.
> 
> The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
> SoCs.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> ---

Acked-by: Santosh Shilimkar <ssantosh@kernel.org>

Re: [PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> From: "Andrew F. Davis" <afd@ti.com>
> 
> The DSPs are expected to be in reset when the driver probes a device.
> If the DSPs are out of reset in probe, the system may crash when the
> firmware is being loaded. So, add a check to make sure the DSP resets
> are asserted, and if not, throw a eye-catchy warning and assert the
> resets specifically.
> 
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> [s-anna@ti.com: replace warning with a WARN]
> Signed-off-by: Suman Anna <s-anna@ti.com>
> ---
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>

Re: [PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> From: "Andrew F. Davis" <afd-l0cyMroinI0@public.gmane.org>
> 
> The DSPs are expected to be in reset when the driver probes a device.
> If the DSPs are out of reset in probe, the system may crash when the
> firmware is being loaded. So, add a check to make sure the DSP resets
> are asserted, and if not, throw a eye-catchy warning and assert the
> resets specifically.
> 
> Signed-off-by: Andrew F. Davis <afd-l0cyMroinI0@public.gmane.org>
> [s-anna-l0cyMroinI0@public.gmane.org: replace warning with a WARN]
> Signed-off-by: Suman Anna <s-anna-l0cyMroinI0@public.gmane.org>
> ---
Acked-by: Santosh Shilimkar <ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 3/3] remoteproc/keystone: Ensure the DSPs are in reset in probe

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> From: "Andrew F. Davis" <afd@ti.com>
> 
> The DSPs are expected to be in reset when the driver probes a device.
> If the DSPs are out of reset in probe, the system may crash when the
> firmware is being loaded. So, add a check to make sure the DSP resets
> are asserted, and if not, throw a eye-catchy warning and assert the
> resets specifically.
> 
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> [s-anna at ti.com: replace warning with a WARN]
> Signed-off-by: Suman Anna <s-anna@ti.com>
> ---
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>

Re: [PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> Add the device tree bindings document for the Texas Instrument's
> Keystone 2 DSP remoteproc devices.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> ---
> v2 Changes:
>   - Modified the patch title
>   - Dropped unstable binding status
>   - Dropped the 'label' property and replaced the device node description
>     to use an alias
>   - Renamed 'kick-gpio' to 'kick-gpios'
>   - Updated the example

Looks reasonable to me. Ofcourse you need Rob's ack for this one.

Acked-by: Santosh Shilimkar <ssantosh@kernel.org>

Re: [PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> Add the device tree bindings document for the Texas Instrument's
> Keystone 2 DSP remoteproc devices.
> 
> Signed-off-by: Suman Anna <s-anna-l0cyMroinI0@public.gmane.org>
> Signed-off-by: Sam Nelson <sam.nelson-l0cyMroinI0@public.gmane.org>
> ---
> v2 Changes:
>   - Modified the patch title
>   - Dropped unstable binding status
>   - Dropped the 'label' property and replaced the device node description
>     to use an alias
>   - Renamed 'kick-gpio' to 'kick-gpios'
>   - Updated the example

Looks reasonable to me. Ofcourse you need Rob's ack for this one.

Acked-by: Santosh Shilimkar <ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 1/3] dt-bindings: remoteproc: Add Keystone DSP remoteproc binding

[Santosh Shilimkar]

On 6/7/2017 5:24 PM, Suman Anna wrote:
> Add the device tree bindings document for the Texas Instrument's
> Keystone 2 DSP remoteproc devices.
> 
> Signed-off-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Sam Nelson <sam.nelson@ti.com>
> ---
> v2 Changes:
>   - Modified the patch title
>   - Dropped unstable binding status
>   - Dropped the 'label' property and replaced the device node description
>     to use an alias
>   - Renamed 'kick-gpio' to 'kick-gpios'
>   - Updated the example

Looks reasonable to me. Ofcourse you need Rob's ack for this one.

Acked-by: Santosh Shilimkar <ssantosh@kernel.org>