[PATCH v3 0/8] Various patches for SAMA5D2 backup mode

[PATCH v3 0/8] Various patches for SAMA5D2 backup mode

[Romain Izard]

While the core of the backup mode for SAMA5D2 has been integrated in
v4.13, it is far from complete. Individual controllers in the chip have
drivers that do not support the reset of the registers during suspend,
and they need to be adapted to handle it.

The first patch uses the clock wakeup code from the prototype backup
mode instead of the version integrated in the mainline, as the mainline
version is not stable. During a test loop with two-second backup
suspend, the mainline version will hang in less than one day, whereas
the prototype version has been running the same test for more than a
week without hanging.

While all these patches are provided in a series, the clock, mtd,
usb, pwm and mfd patch do not depend on each other.

Changes in v2:
* drop the IIO patch duplicating existing code
* determine the number of programmable clocks to save dynamically
* declare a required local variable in the tty/serial patch

Changes in v3:
* drop dev_printk changes for PMECC
* rework the resume code for PMECC
* improve comments on PMC clock handling

Romain Izard (8):
  clk: at91: pmc: Wait for clocks when resuming
  clk: at91: pmc: Save SCSR during suspend
  clk: at91: pmc: Support backup for programmable clocks
  mtd: nand: atmel: Avoid ECC errors when leaving backup mode
  ehci-atmel: Power down during suspend is normal
  pwm: atmel-tcb: Support backup mode
  atmel_flexcom: Support backup mode
  tty/serial: atmel: Prevent a warning on suspend

 drivers/clk/at91/clk-programmable.c      |  2 +
 drivers/clk/at91/pmc.c                   | 63 ++++++++++++++++++++++++++-----
 drivers/clk/at91/pmc.h                   |  2 +
 drivers/mfd/atmel-flexcom.c              | 65 ++++++++++++++++++++++++--------
 drivers/mtd/nand/atmel/nand-controller.c |  3 ++
 drivers/mtd/nand/atmel/pmecc.c           | 22 +++++++----
 drivers/mtd/nand/atmel/pmecc.h           |  1 +
 drivers/pwm/pwm-atmel-tcb.c              | 63 ++++++++++++++++++++++++++++++-
 drivers/tty/serial/atmel_serial.c        | 13 +++++++
 drivers/usb/host/ehci-atmel.c            |  3 +-
 10 files changed, 201 insertions(+), 36 deletions(-)

-- 
2.11.0

[PATCH v3 0/8] Various patches for SAMA5D2 backup mode

[Romain Izard]

While the core of the backup mode for SAMA5D2 has been integrated in
v4.13, it is far from complete. Individual controllers in the chip have
drivers that do not support the reset of the registers during suspend,
and they need to be adapted to handle it.

The first patch uses the clock wakeup code from the prototype backup
mode instead of the version integrated in the mainline, as the mainline
version is not stable. During a test loop with two-second backup
suspend, the mainline version will hang in less than one day, whereas
the prototype version has been running the same test for more than a
week without hanging.

While all these patches are provided in a series, the clock, mtd,
usb, pwm and mfd patch do not depend on each other.

Changes in v2:
* drop the IIO patch duplicating existing code
* determine the number of programmable clocks to save dynamically
* declare a required local variable in the tty/serial patch

Changes in v3:
* drop dev_printk changes for PMECC
* rework the resume code for PMECC
* improve comments on PMC clock handling

Romain Izard (8):
  clk: at91: pmc: Wait for clocks when resuming
  clk: at91: pmc: Save SCSR during suspend
  clk: at91: pmc: Support backup for programmable clocks
  mtd: nand: atmel: Avoid ECC errors when leaving backup mode
  ehci-atmel: Power down during suspend is normal
  pwm: atmel-tcb: Support backup mode
  atmel_flexcom: Support backup mode
  tty/serial: atmel: Prevent a warning on suspend

 drivers/clk/at91/clk-programmable.c      |  2 +
 drivers/clk/at91/pmc.c                   | 63 ++++++++++++++++++++++++++-----
 drivers/clk/at91/pmc.h                   |  2 +
 drivers/mfd/atmel-flexcom.c              | 65 ++++++++++++++++++++++++--------
 drivers/mtd/nand/atmel/nand-controller.c |  3 ++
 drivers/mtd/nand/atmel/pmecc.c           | 22 +++++++----
 drivers/mtd/nand/atmel/pmecc.h           |  1 +
 drivers/pwm/pwm-atmel-tcb.c              | 63 ++++++++++++++++++++++++++++++-
 drivers/tty/serial/atmel_serial.c        | 13 +++++++
 drivers/usb/host/ehci-atmel.c            |  3 +-
 10 files changed, 201 insertions(+), 36 deletions(-)

-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v3 1/8] clk: at91: pmc: Wait for clocks when resuming

[Romain Izard]

Wait for the syncronization of all clocks when resuming, not only the
UPLL clock. Do not use regmap_read_poll_timeout, as it will call BUG()
when interrupts are masked, which is the case in here.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/clk/at91/pmc.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 775af473fe11..5c2b26de303e 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -107,10 +107,20 @@ static int pmc_suspend(void)
 	return 0;
 }
 
+static bool pmc_ready(unsigned int mask)
+{
+	unsigned int status;
+
+	regmap_read(pmcreg, AT91_PMC_SR, &status);
+
+	return ((status & mask) == mask) ? 1 : 0;
+}
+
 static void pmc_resume(void)
 {
-	int i, ret = 0;
+	int i;
 	u32 tmp;
+	u32 mask = AT91_PMC_MCKRDY | AT91_PMC_LOCKA;
 
 	regmap_read(pmcreg, AT91_PMC_MCKR, &tmp);
 	if (pmc_cache.mckr != tmp)
@@ -134,13 +144,11 @@ static void pmc_resume(void)
 			     AT91_PMC_PCR_CMD);
 	}
 
-	if (pmc_cache.uckr & AT91_PMC_UPLLEN) {
-		ret = regmap_read_poll_timeout(pmcreg, AT91_PMC_SR, tmp,
-					       !(tmp & AT91_PMC_LOCKU),
-					       10, 5000);
-		if (ret)
-			pr_crit("USB PLL didn't lock when resuming\n");
-	}
+	if (pmc_cache.uckr & AT91_PMC_UPLLEN)
+		mask |= AT91_PMC_LOCKU;
+
+	while (!pmc_ready(mask))
+		cpu_relax();
 }
 
 static struct syscore_ops pmc_syscore_ops = {
-- 
2.11.0

[PATCH v3 1/8] clk: at91: pmc: Wait for clocks when resuming

[Romain Izard]

Wait for the syncronization of all clocks when resuming, not only the
UPLL clock. Do not use regmap_read_poll_timeout, as it will call BUG()
when interrupts are masked, which is the case in here.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/clk/at91/pmc.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 775af473fe11..5c2b26de303e 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -107,10 +107,20 @@ static int pmc_suspend(void)
 	return 0;
 }
 
+static bool pmc_ready(unsigned int mask)
+{
+	unsigned int status;
+
+	regmap_read(pmcreg, AT91_PMC_SR, &status);
+
+	return ((status & mask) == mask) ? 1 : 0;
+}
+
 static void pmc_resume(void)
 {
-	int i, ret = 0;
+	int i;
 	u32 tmp;
+	u32 mask = AT91_PMC_MCKRDY | AT91_PMC_LOCKA;
 
 	regmap_read(pmcreg, AT91_PMC_MCKR, &tmp);
 	if (pmc_cache.mckr != tmp)
@@ -134,13 +144,11 @@ static void pmc_resume(void)
 			     AT91_PMC_PCR_CMD);
 	}
 
-	if (pmc_cache.uckr & AT91_PMC_UPLLEN) {
-		ret = regmap_read_poll_timeout(pmcreg, AT91_PMC_SR, tmp,
-					       !(tmp & AT91_PMC_LOCKU),
-					       10, 5000);
-		if (ret)
-			pr_crit("USB PLL didn't lock when resuming\n");
-	}
+	if (pmc_cache.uckr & AT91_PMC_UPLLEN)
+		mask |= AT91_PMC_LOCKU;
+
+	while (!pmc_ready(mask))
+		cpu_relax();
 }
 
 static struct syscore_ops pmc_syscore_ops = {
-- 
2.11.0

[PATCH v3 2/8] clk: at91: pmc: Save SCSR during suspend

[Romain Izard]

The contents of the System Clock Status Register (SCSR) needs to be
restored into the System Clock Enable Register (SCER).

As the bootloader will restore some clocks by itself, the issue can be
missed as only the USB controller, the LCD controller, the Image Sensor
controller and the programmable clocks will be impacted.

Fix the obvious typo in the suspend/resume code, as the IMR register
does not need to be saved twice.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/clk/at91/pmc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 5c2b26de303e..07dc2861ad3f 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -86,7 +86,7 @@ static int pmc_suspend(void)
 {
 	int i;
 
-	regmap_read(pmcreg, AT91_PMC_IMR, &pmc_cache.scsr);
+	regmap_read(pmcreg, AT91_PMC_SCSR, &pmc_cache.scsr);
 	regmap_read(pmcreg, AT91_PMC_PCSR, &pmc_cache.pcsr0);
 	regmap_read(pmcreg, AT91_CKGR_UCKR, &pmc_cache.uckr);
 	regmap_read(pmcreg, AT91_CKGR_MOR, &pmc_cache.mor);
@@ -129,7 +129,7 @@ static void pmc_resume(void)
 	if (pmc_cache.pllar != tmp)
 		pr_warn("PLLAR was not configured properly by the firmware\n");
 
-	regmap_write(pmcreg, AT91_PMC_IMR, pmc_cache.scsr);
+	regmap_write(pmcreg, AT91_PMC_SCER, pmc_cache.scsr);
 	regmap_write(pmcreg, AT91_PMC_PCER, pmc_cache.pcsr0);
 	regmap_write(pmcreg, AT91_CKGR_UCKR, pmc_cache.uckr);
 	regmap_write(pmcreg, AT91_CKGR_MOR, pmc_cache.mor);
-- 
2.11.0

[PATCH v3 2/8] clk: at91: pmc: Save SCSR during suspend

[Romain Izard]

The contents of the System Clock Status Register (SCSR) needs to be
restored into the System Clock Enable Register (SCER).

As the bootloader will restore some clocks by itself, the issue can be
missed as only the USB controller, the LCD controller, the Image Sensor
controller and the programmable clocks will be impacted.

Fix the obvious typo in the suspend/resume code, as the IMR register
does not need to be saved twice.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/clk/at91/pmc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 5c2b26de303e..07dc2861ad3f 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -86,7 +86,7 @@ static int pmc_suspend(void)
 {
 	int i;
 
-	regmap_read(pmcreg, AT91_PMC_IMR, &pmc_cache.scsr);
+	regmap_read(pmcreg, AT91_PMC_SCSR, &pmc_cache.scsr);
 	regmap_read(pmcreg, AT91_PMC_PCSR, &pmc_cache.pcsr0);
 	regmap_read(pmcreg, AT91_CKGR_UCKR, &pmc_cache.uckr);
 	regmap_read(pmcreg, AT91_CKGR_MOR, &pmc_cache.mor);
@@ -129,7 +129,7 @@ static void pmc_resume(void)
 	if (pmc_cache.pllar != tmp)
 		pr_warn("PLLAR was not configured properly by the firmware\n");
 
-	regmap_write(pmcreg, AT91_PMC_IMR, pmc_cache.scsr);
+	regmap_write(pmcreg, AT91_PMC_SCER, pmc_cache.scsr);
 	regmap_write(pmcreg, AT91_PMC_PCER, pmc_cache.pcsr0);
 	regmap_write(pmcreg, AT91_CKGR_UCKR, pmc_cache.uckr);
 	regmap_write(pmcreg, AT91_CKGR_MOR, pmc_cache.mor);
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v3 3/8] clk: at91: pmc: Support backup for programmable clocks

[Romain Izard]

From: Romain Izard <romain.izard@mobile-devices.fr>

When an AT91 programmable clock is declared in the device tree, register
it into the Power Management Controller driver. On entering suspend mode,
the driver saves and restores the Programmable Clock registers to support
the backup mode for these clocks.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
Changes in v2:
* register PCKs on clock startup
Chnages in v3:
* improve comments on hanling 0 in pmc_register_id and pmc_register_pck
* declare local variables earlier for checkpatch

 drivers/clk/at91/clk-programmable.c |  2 ++
 drivers/clk/at91/pmc.c              | 35 +++++++++++++++++++++++++++++++++++
 drivers/clk/at91/pmc.h              |  2 ++
 3 files changed, 39 insertions(+)

diff --git a/drivers/clk/at91/clk-programmable.c b/drivers/clk/at91/clk-programmable.c
index 85a449cf61e3..0e6aab1252fc 100644
--- a/drivers/clk/at91/clk-programmable.c
+++ b/drivers/clk/at91/clk-programmable.c
@@ -204,6 +204,8 @@ at91_clk_register_programmable(struct regmap *regmap,
 	if (ret) {
 		kfree(prog);
 		hw = ERR_PTR(ret);
+	} else {
+		pmc_register_pck(id);
 	}
 
 	return hw;
diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 07dc2861ad3f..1fa27f4ea538 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -22,6 +22,7 @@
 #include "pmc.h"
 
 #define PMC_MAX_IDS 128
+#define PMC_MAX_PCKS 8
 
 int of_at91_get_clk_range(struct device_node *np, const char *propname,
 			  struct clk_range *range)
@@ -50,6 +51,7 @@ EXPORT_SYMBOL_GPL(of_at91_get_clk_range);
 static struct regmap *pmcreg;
 
 static u8 registered_ids[PMC_MAX_IDS];
+static u8 registered_pcks[PMC_MAX_PCKS];
 
 static struct
 {
@@ -66,8 +68,13 @@ static struct
 	u32 pcr[PMC_MAX_IDS];
 	u32 audio_pll0;
 	u32 audio_pll1;
+	u32 pckr[PMC_MAX_PCKS];
 } pmc_cache;
 
+/*
+ * As Peripheral ID 0 is invalid on AT91 chips, the identifier is stored
+ * without alteration in the table, and 0 is for unused clocks.
+ */
 void pmc_register_id(u8 id)
 {
 	int i;
@@ -82,9 +89,28 @@ void pmc_register_id(u8 id)
 	}
 }
 
+/*
+ * As Programmable Clock 0 is valid on AT91 chips, there is an offset
+ * of 1 between the stored value and the real clock ID.
+ */
+void pmc_register_pck(u8 pck)
+{
+	int i;
+
+	for (i = 0; i < PMC_MAX_PCKS; i++) {
+		if (registered_pcks[i] == 0) {
+			registered_pcks[i] = pck + 1;
+			break;
+		}
+		if (registered_pcks[i] == (pck + 1))
+			break;
+	}
+}
+
 static int pmc_suspend(void)
 {
 	int i;
+	u8 num;
 
 	regmap_read(pmcreg, AT91_PMC_SCSR, &pmc_cache.scsr);
 	regmap_read(pmcreg, AT91_PMC_PCSR, &pmc_cache.pcsr0);
@@ -103,6 +129,10 @@ static int pmc_suspend(void)
 		regmap_read(pmcreg, AT91_PMC_PCR,
 			    &pmc_cache.pcr[registered_ids[i]]);
 	}
+	for (i = 0; registered_pcks[i]; i++) {
+		num = registered_pcks[i] - 1;
+		regmap_read(pmcreg, AT91_PMC_PCKR(num), &pmc_cache.pckr[num]);
+	}
 
 	return 0;
 }
@@ -119,6 +149,7 @@ static bool pmc_ready(unsigned int mask)
 static void pmc_resume(void)
 {
 	int i;
+	u8 num;
 	u32 tmp;
 	u32 mask = AT91_PMC_MCKRDY | AT91_PMC_LOCKA;
 
@@ -143,6 +174,10 @@ static void pmc_resume(void)
 			     pmc_cache.pcr[registered_ids[i]] |
 			     AT91_PMC_PCR_CMD);
 	}
+	for (i = 0; registered_pcks[i]; i++) {
+		num = registered_pcks[i] - 1;
+		regmap_write(pmcreg, AT91_PMC_PCKR(num), pmc_cache.pckr[num]);
+	}
 
 	if (pmc_cache.uckr & AT91_PMC_UPLLEN)
 		mask |= AT91_PMC_LOCKU;
diff --git a/drivers/clk/at91/pmc.h b/drivers/clk/at91/pmc.h
index 858e8ef7e8db..d22b1fa9ecdc 100644
--- a/drivers/clk/at91/pmc.h
+++ b/drivers/clk/at91/pmc.h
@@ -31,8 +31,10 @@ int of_at91_get_clk_range(struct device_node *np, const char *propname,
 
 #ifdef CONFIG_PM
 void pmc_register_id(u8 id);
+void pmc_register_pck(u8 pck);
 #else
 static inline void pmc_register_id(u8 id) {}
+static inline void pmc_register_pck(u8 pck) {}
 #endif
 
 #endif /* __PMC_H_ */
-- 
2.11.0

[PATCH v3 3/8] clk: at91: pmc: Support backup for programmable clocks

[Romain Izard]

From: Romain Izard <romain.izard@mobile-devices.fr>

When an AT91 programmable clock is declared in the device tree, register
it into the Power Management Controller driver. On entering suspend mode,
the driver saves and restores the Programmable Clock registers to support
the backup mode for these clocks.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
Changes in v2:
* register PCKs on clock startup
Chnages in v3:
* improve comments on hanling 0 in pmc_register_id and pmc_register_pck
* declare local variables earlier for checkpatch

 drivers/clk/at91/clk-programmable.c |  2 ++
 drivers/clk/at91/pmc.c              | 35 +++++++++++++++++++++++++++++++++++
 drivers/clk/at91/pmc.h              |  2 ++
 3 files changed, 39 insertions(+)

diff --git a/drivers/clk/at91/clk-programmable.c b/drivers/clk/at91/clk-programmable.c
index 85a449cf61e3..0e6aab1252fc 100644
--- a/drivers/clk/at91/clk-programmable.c
+++ b/drivers/clk/at91/clk-programmable.c
@@ -204,6 +204,8 @@ at91_clk_register_programmable(struct regmap *regmap,
 	if (ret) {
 		kfree(prog);
 		hw = ERR_PTR(ret);
+	} else {
+		pmc_register_pck(id);
 	}
 
 	return hw;
diff --git a/drivers/clk/at91/pmc.c b/drivers/clk/at91/pmc.c
index 07dc2861ad3f..1fa27f4ea538 100644
--- a/drivers/clk/at91/pmc.c
+++ b/drivers/clk/at91/pmc.c
@@ -22,6 +22,7 @@
 #include "pmc.h"
 
 #define PMC_MAX_IDS 128
+#define PMC_MAX_PCKS 8
 
 int of_at91_get_clk_range(struct device_node *np, const char *propname,
 			  struct clk_range *range)
@@ -50,6 +51,7 @@ EXPORT_SYMBOL_GPL(of_at91_get_clk_range);
 static struct regmap *pmcreg;
 
 static u8 registered_ids[PMC_MAX_IDS];
+static u8 registered_pcks[PMC_MAX_PCKS];
 
 static struct
 {
@@ -66,8 +68,13 @@ static struct
 	u32 pcr[PMC_MAX_IDS];
 	u32 audio_pll0;
 	u32 audio_pll1;
+	u32 pckr[PMC_MAX_PCKS];
 } pmc_cache;
 
+/*
+ * As Peripheral ID 0 is invalid on AT91 chips, the identifier is stored
+ * without alteration in the table, and 0 is for unused clocks.
+ */
 void pmc_register_id(u8 id)
 {
 	int i;
@@ -82,9 +89,28 @@ void pmc_register_id(u8 id)
 	}
 }
 
+/*
+ * As Programmable Clock 0 is valid on AT91 chips, there is an offset
+ * of 1 between the stored value and the real clock ID.
+ */
+void pmc_register_pck(u8 pck)
+{
+	int i;
+
+	for (i = 0; i < PMC_MAX_PCKS; i++) {
+		if (registered_pcks[i] == 0) {
+			registered_pcks[i] = pck + 1;
+			break;
+		}
+		if (registered_pcks[i] == (pck + 1))
+			break;
+	}
+}
+
 static int pmc_suspend(void)
 {
 	int i;
+	u8 num;
 
 	regmap_read(pmcreg, AT91_PMC_SCSR, &pmc_cache.scsr);
 	regmap_read(pmcreg, AT91_PMC_PCSR, &pmc_cache.pcsr0);
@@ -103,6 +129,10 @@ static int pmc_suspend(void)
 		regmap_read(pmcreg, AT91_PMC_PCR,
 			    &pmc_cache.pcr[registered_ids[i]]);
 	}
+	for (i = 0; registered_pcks[i]; i++) {
+		num = registered_pcks[i] - 1;
+		regmap_read(pmcreg, AT91_PMC_PCKR(num), &pmc_cache.pckr[num]);
+	}
 
 	return 0;
 }
@@ -119,6 +149,7 @@ static bool pmc_ready(unsigned int mask)
 static void pmc_resume(void)
 {
 	int i;
+	u8 num;
 	u32 tmp;
 	u32 mask = AT91_PMC_MCKRDY | AT91_PMC_LOCKA;
 
@@ -143,6 +174,10 @@ static void pmc_resume(void)
 			     pmc_cache.pcr[registered_ids[i]] |
 			     AT91_PMC_PCR_CMD);
 	}
+	for (i = 0; registered_pcks[i]; i++) {
+		num = registered_pcks[i] - 1;
+		regmap_write(pmcreg, AT91_PMC_PCKR(num), pmc_cache.pckr[num]);
+	}
 
 	if (pmc_cache.uckr & AT91_PMC_UPLLEN)
 		mask |= AT91_PMC_LOCKU;
diff --git a/drivers/clk/at91/pmc.h b/drivers/clk/at91/pmc.h
index 858e8ef7e8db..d22b1fa9ecdc 100644
--- a/drivers/clk/at91/pmc.h
+++ b/drivers/clk/at91/pmc.h
@@ -31,8 +31,10 @@ int of_at91_get_clk_range(struct device_node *np, const char *propname,
 
 #ifdef CONFIG_PM
 void pmc_register_id(u8 id);
+void pmc_register_pck(u8 pck);
 #else
 static inline void pmc_register_id(u8 id) {}
+static inline void pmc_register_pck(u8 pck) {}
 #endif
 
 #endif /* __PMC_H_ */
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Romain Izard]

During backup mode, the contents of all registers will be cleared as the
SoC will be completely powered down. For a product that boots on NAND
Flash memory, the bootloader will obviously use the related controller
to read the Flash and correct any detected error in the memory, before
handling back control to the kernel's resuming entry point.

But it does not clean the NAND controller registers after use and on its
side the kernel driver expects the error locator to be powered down and
in a clean state. Add a resume hook for the PMECC error locator, and
reset its registers.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
---
Change in v3:
* keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
  reset the controller after the bootloader has left it enabled.

 drivers/mtd/nand/atmel/nand-controller.c |  3 +++
 drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
 drivers/mtd/nand/atmel/pmecc.h           |  1 +
 3 files changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
index f25eca79f4e5..86c2199380c2 100644
--- a/drivers/mtd/nand/atmel/nand-controller.c
+++ b/drivers/mtd/nand/atmel/nand-controller.c
@@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
 	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
 	struct atmel_nand *nand;
 
+	if (nand->pmecc)
+		atmel_pmecc_resume(nand->pmecc);
+
 	list_for_each_entry(nand, &nc->chips, node) {
 		int i;
 
diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
index 146af8218314..ff09c0f25dd4 100644
--- a/drivers/mtd/nand/atmel/pmecc.c
+++ b/drivers/mtd/nand/atmel/pmecc.c
@@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
 
+void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
+{
+	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+}
+
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op)
 {
 	struct atmel_pmecc *pmecc = user->pmecc;
@@ -797,14 +803,17 @@ EXPORT_SYMBOL_GPL(atmel_pmecc_enable);
 
 void atmel_pmecc_disable(struct atmel_pmecc_user *user)
 {
-	struct atmel_pmecc *pmecc = user->pmecc;
-
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(user->pmecc);
 	mutex_unlock(&user->pmecc->lock);
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_disable);
 
+void atmel_pmecc_resume(struct atmel_pmecc_user *user)
+{
+	atmel_pmecc_reset(user->pmecc);
+}
+EXPORT_SYMBOL_GPL(atmel_pmecc_resume);
+
 int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user)
 {
 	struct atmel_pmecc *pmecc = user->pmecc;
@@ -855,10 +864,7 @@ static struct atmel_pmecc *atmel_pmecc_create(struct platform_device *pdev,
 
 	/* Disable all interrupts before registering the PMECC handler. */
 	writel(0xffffffff, pmecc->regs.base + ATMEL_PMECC_IDR);
-
-	/* Reset the ECC engine */
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(pmecc);
 
 	return pmecc;
 }
diff --git a/drivers/mtd/nand/atmel/pmecc.h b/drivers/mtd/nand/atmel/pmecc.h
index a8ddbfca2ea5..488a90f1965d 100644
--- a/drivers/mtd/nand/atmel/pmecc.h
+++ b/drivers/mtd/nand/atmel/pmecc.h
@@ -63,6 +63,7 @@ void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user);
 
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op);
 void atmel_pmecc_disable(struct atmel_pmecc_user *user);
+void atmel_pmecc_resume(struct atmel_pmecc_user *user);
 int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user);
 int atmel_pmecc_correct_sector(struct atmel_pmecc_user *user, int sector,
 			       void *data, void *ecc);
-- 
2.11.0

[PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Romain Izard]

During backup mode, the contents of all registers will be cleared as the
SoC will be completely powered down. For a product that boots on NAND
Flash memory, the bootloader will obviously use the related controller
to read the Flash and correct any detected error in the memory, before
handling back control to the kernel's resuming entry point.

But it does not clean the NAND controller registers after use and on its
side the kernel driver expects the error locator to be powered down and
in a clean state. Add a resume hook for the PMECC error locator, and
reset its registers.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
---
Change in v3:
* keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
  reset the controller after the bootloader has left it enabled.

 drivers/mtd/nand/atmel/nand-controller.c |  3 +++
 drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
 drivers/mtd/nand/atmel/pmecc.h           |  1 +
 3 files changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
index f25eca79f4e5..86c2199380c2 100644
--- a/drivers/mtd/nand/atmel/nand-controller.c
+++ b/drivers/mtd/nand/atmel/nand-controller.c
@@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
 	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
 	struct atmel_nand *nand;
 
+	if (nand->pmecc)
+		atmel_pmecc_resume(nand->pmecc);
+
 	list_for_each_entry(nand, &nc->chips, node) {
 		int i;
 
diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
index 146af8218314..ff09c0f25dd4 100644
--- a/drivers/mtd/nand/atmel/pmecc.c
+++ b/drivers/mtd/nand/atmel/pmecc.c
@@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
 
+void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
+{
+	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+}
+
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op)
 {
 	struct atmel_pmecc *pmecc = user->pmecc;
@@ -797,14 +803,17 @@ EXPORT_SYMBOL_GPL(atmel_pmecc_enable);
 
 void atmel_pmecc_disable(struct atmel_pmecc_user *user)
 {
-	struct atmel_pmecc *pmecc = user->pmecc;
-
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(user->pmecc);
 	mutex_unlock(&user->pmecc->lock);
 }
 EXPORT_SYMBOL_GPL(atmel_pmecc_disable);
 
+void atmel_pmecc_resume(struct atmel_pmecc_user *user)
+{
+	atmel_pmecc_reset(user->pmecc);
+}
+EXPORT_SYMBOL_GPL(atmel_pmecc_resume);
+
 int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user)
 {
 	struct atmel_pmecc *pmecc = user->pmecc;
@@ -855,10 +864,7 @@ static struct atmel_pmecc *atmel_pmecc_create(struct platform_device *pdev,
 
 	/* Disable all interrupts before registering the PMECC handler. */
 	writel(0xffffffff, pmecc->regs.base + ATMEL_PMECC_IDR);
-
-	/* Reset the ECC engine */
-	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
-	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
+	atmel_pmecc_reset(pmecc);
 
 	return pmecc;
 }
diff --git a/drivers/mtd/nand/atmel/pmecc.h b/drivers/mtd/nand/atmel/pmecc.h
index a8ddbfca2ea5..488a90f1965d 100644
--- a/drivers/mtd/nand/atmel/pmecc.h
+++ b/drivers/mtd/nand/atmel/pmecc.h
@@ -63,6 +63,7 @@ void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user);
 
 int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op);
 void atmel_pmecc_disable(struct atmel_pmecc_user *user);
+void atmel_pmecc_resume(struct atmel_pmecc_user *user);
 int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user);
 int atmel_pmecc_correct_sector(struct atmel_pmecc_user *user, int sector,
 			       void *data, void *ecc);
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Boris Brezillon]

On Wed, 27 Sep 2017 10:35:51 +0200
Romain Izard <romain.izard.pro@gmail.com> wrote:

> During backup mode, the contents of all registers will be cleared as the
> SoC will be completely powered down. For a product that boots on NAND
> Flash memory, the bootloader will obviously use the related controller
> to read the Flash and correct any detected error in the memory, before
> handling back control to the kernel's resuming entry point.
> 
> But it does not clean the NAND controller registers after use and on its
> side the kernel driver expects the error locator to be powered down and
> in a clean state. Add a resume hook for the PMECC error locator, and
> reset its registers.
> 
> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
> ---
> Change in v3:
> * keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
>   reset the controller after the bootloader has left it enabled.
> 
>  drivers/mtd/nand/atmel/nand-controller.c |  3 +++
>  drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
>  drivers/mtd/nand/atmel/pmecc.h           |  1 +
>  3 files changed, 18 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
> index f25eca79f4e5..86c2199380c2 100644
> --- a/drivers/mtd/nand/atmel/nand-controller.c
> +++ b/drivers/mtd/nand/atmel/nand-controller.c
> @@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
>  	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
>  	struct atmel_nand *nand;
>  
> +	if (nand->pmecc)
> +		atmel_pmecc_resume(nand->pmecc);
> +

nand is used uninitialized here, and atmel_pmecc_resume() should be
passed a atmel_pmecc object not a atmel_pmecc_user.

	if (nc->pmecc)
		atmel_pmecc_resume(nc->pmecc);

>  	list_for_each_entry(nand, &nc->chips, node) {
>  		int i;
>  
> diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
> index 146af8218314..ff09c0f25dd4 100644
> --- a/drivers/mtd/nand/atmel/pmecc.c
> +++ b/drivers/mtd/nand/atmel/pmecc.c
> @@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
>  }
>  EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
>  
> +void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
> +{
> +	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
> +	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
> +}

It's not used outside of this file, so it should have a static
specifier. Anyway, I wonder why you don't expose atmel_pmecc_reset()
directly instead of creating this atmel_pmecc_resume() wrapper.

Re: [PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Boris Brezillon]

On Wed, 27 Sep 2017 10:35:51 +0200
Romain Izard <romain.izard.pro@gmail.com> wrote:

> During backup mode, the contents of all registers will be cleared as the
> SoC will be completely powered down. For a product that boots on NAND
> Flash memory, the bootloader will obviously use the related controller
> to read the Flash and correct any detected error in the memory, before
> handling back control to the kernel's resuming entry point.
> 
> But it does not clean the NAND controller registers after use and on its
> side the kernel driver expects the error locator to be powered down and
> in a clean state. Add a resume hook for the PMECC error locator, and
> reset its registers.
> 
> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
> ---
> Change in v3:
> * keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
>   reset the controller after the bootloader has left it enabled.
> 
>  drivers/mtd/nand/atmel/nand-controller.c |  3 +++
>  drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
>  drivers/mtd/nand/atmel/pmecc.h           |  1 +
>  3 files changed, 18 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
> index f25eca79f4e5..86c2199380c2 100644
> --- a/drivers/mtd/nand/atmel/nand-controller.c
> +++ b/drivers/mtd/nand/atmel/nand-controller.c
> @@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
>  	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
>  	struct atmel_nand *nand;
>  
> +	if (nand->pmecc)
> +		atmel_pmecc_resume(nand->pmecc);
> +

nand is used uninitialized here, and atmel_pmecc_resume() should be
passed a atmel_pmecc object not a atmel_pmecc_user.

	if (nc->pmecc)
		atmel_pmecc_resume(nc->pmecc);

>  	list_for_each_entry(nand, &nc->chips, node) {
>  		int i;
>  
> diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
> index 146af8218314..ff09c0f25dd4 100644
> --- a/drivers/mtd/nand/atmel/pmecc.c
> +++ b/drivers/mtd/nand/atmel/pmecc.c
> @@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
>  }
>  EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
>  
> +void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
> +{
> +	writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
> +	writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
> +}

It's not used outside of this file, so it should have a static
specifier. Anyway, I wonder why you don't expose atmel_pmecc_reset()
directly instead of creating this atmel_pmecc_resume() wrapper.

Re: [PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Romain Izard]

2017-09-27 17:08 GMT+02:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> On Wed, 27 Sep 2017 10:35:51 +0200
> Romain Izard <romain.izard.pro@gmail.com> wrote:
>
>> During backup mode, the contents of all registers will be cleared as the
>> SoC will be completely powered down. For a product that boots on NAND
>> Flash memory, the bootloader will obviously use the related controller
>> to read the Flash and correct any detected error in the memory, before
>> handling back control to the kernel's resuming entry point.
>>
>> But it does not clean the NAND controller registers after use and on its
>> side the kernel driver expects the error locator to be powered down and
>> in a clean state. Add a resume hook for the PMECC error locator, and
>> reset its registers.
>>
>> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
>> ---
>> Change in v3:
>> * keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
>>   reset the controller after the bootloader has left it enabled.
>>
>>  drivers/mtd/nand/atmel/nand-controller.c |  3 +++
>>  drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
>>  drivers/mtd/nand/atmel/pmecc.h           |  1 +
>>  3 files changed, 18 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
>> index f25eca79f4e5..86c2199380c2 100644
>> --- a/drivers/mtd/nand/atmel/nand-controller.c
>> +++ b/drivers/mtd/nand/atmel/nand-controller.c
>> @@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
>>       struct atmel_nand_controller *nc = dev_get_drvdata(dev);
>>       struct atmel_nand *nand;
>>
>> +     if (nand->pmecc)
>> +             atmel_pmecc_resume(nand->pmecc);
>> +
>
> nand is used uninitialized here, and atmel_pmecc_resume() should be
> passed a atmel_pmecc object not a atmel_pmecc_user.
>
>         if (nc->pmecc)
>                 atmel_pmecc_resume(nc->pmecc);
>
And yet I thought I correctly tested this code...

:(

>>       list_for_each_entry(nand, &nc->chips, node) {
>>               int i;
>>
>> diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
>> index 146af8218314..ff09c0f25dd4 100644
>> --- a/drivers/mtd/nand/atmel/pmecc.c
>> +++ b/drivers/mtd/nand/atmel/pmecc.c
>> @@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
>>  }
>>  EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
>>
>> +void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
>> +{
>> +     writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
>> +     writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
>> +}
>
> It's not used outside of this file, so it should have a static
> specifier. Anyway, I wonder why you don't expose atmel_pmecc_reset()
> directly instead of creating this atmel_pmecc_resume() wrapper.

I will fix this...

-- 
Romain Izard

Re: [PATCH v3 4/8] mtd: nand: atmel: Avoid ECC errors when leaving backup mode

[Romain Izard]

2017-09-27 17:08 GMT+02:00 Boris Brezillon <boris.brezillon@free-electrons.com>:
> On Wed, 27 Sep 2017 10:35:51 +0200
> Romain Izard <romain.izard.pro@gmail.com> wrote:
>
>> During backup mode, the contents of all registers will be cleared as the
>> SoC will be completely powered down. For a product that boots on NAND
>> Flash memory, the bootloader will obviously use the related controller
>> to read the Flash and correct any detected error in the memory, before
>> handling back control to the kernel's resuming entry point.
>>
>> But it does not clean the NAND controller registers after use and on its
>> side the kernel driver expects the error locator to be powered down and
>> in a clean state. Add a resume hook for the PMECC error locator, and
>> reset its registers.
>>
>> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
>> ---
>> Change in v3:
>> * keep the PMECC disabled when not in use, and use atmel_pmecc_resume to
>>   reset the controller after the bootloader has left it enabled.
>>
>>  drivers/mtd/nand/atmel/nand-controller.c |  3 +++
>>  drivers/mtd/nand/atmel/pmecc.c           | 22 ++++++++++++++--------
>>  drivers/mtd/nand/atmel/pmecc.h           |  1 +
>>  3 files changed, 18 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
>> index f25eca79f4e5..86c2199380c2 100644
>> --- a/drivers/mtd/nand/atmel/nand-controller.c
>> +++ b/drivers/mtd/nand/atmel/nand-controller.c
>> @@ -2530,6 +2530,9 @@ static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
>>       struct atmel_nand_controller *nc = dev_get_drvdata(dev);
>>       struct atmel_nand *nand;
>>
>> +     if (nand->pmecc)
>> +             atmel_pmecc_resume(nand->pmecc);
>> +
>
> nand is used uninitialized here, and atmel_pmecc_resume() should be
> passed a atmel_pmecc object not a atmel_pmecc_user.
>
>         if (nc->pmecc)
>                 atmel_pmecc_resume(nc->pmecc);
>
And yet I thought I correctly tested this code...

:(

>>       list_for_each_entry(nand, &nc->chips, node) {
>>               int i;
>>
>> diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/atmel/pmecc.c
>> index 146af8218314..ff09c0f25dd4 100644
>> --- a/drivers/mtd/nand/atmel/pmecc.c
>> +++ b/drivers/mtd/nand/atmel/pmecc.c
>> @@ -765,6 +765,12 @@ void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
>>  }
>>  EXPORT_SYMBOL_GPL(atmel_pmecc_get_generated_eccbytes);
>>
>> +void atmel_pmecc_reset(struct atmel_pmecc *pmecc)
>> +{
>> +     writel(PMECC_CTRL_RST, pmecc->regs.base + ATMEL_PMECC_CTRL);
>> +     writel(PMECC_CTRL_DISABLE, pmecc->regs.base + ATMEL_PMECC_CTRL);
>> +}
>
> It's not used outside of this file, so it should have a static
> specifier. Anyway, I wonder why you don't expose atmel_pmecc_reset()
> directly instead of creating this atmel_pmecc_resume() wrapper.

I will fix this...

-- 
Romain Izard

[PATCH v3 5/8] ehci-atmel: Power down during suspend is normal

[Romain Izard]

When an Atmel SoC is suspended with the backup mode, the USB bus will be
powered down. As this is expected, do not return an error to the driver
core when ehci_resume detects it.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/usb/host/ehci-atmel.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c
index 7440722bfbf0..2a8b9bdc0e57 100644
--- a/drivers/usb/host/ehci-atmel.c
+++ b/drivers/usb/host/ehci-atmel.c
@@ -205,7 +205,8 @@ static int __maybe_unused ehci_atmel_drv_resume(struct device *dev)
 	struct atmel_ehci_priv *atmel_ehci = hcd_to_atmel_ehci_priv(hcd);
 
 	atmel_start_clock(atmel_ehci);
-	return ehci_resume(hcd, false);
+	ehci_resume(hcd, false);
+	return 0;
 }
 
 #ifdef CONFIG_OF
-- 
2.11.0

[PATCH v3 5/8] ehci-atmel: Power down during suspend is normal

[Romain Izard]

When an Atmel SoC is suspended with the backup mode, the USB bus will be
powered down. As this is expected, do not return an error to the driver
core when ehci_resume detects it.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/usb/host/ehci-atmel.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c
index 7440722bfbf0..2a8b9bdc0e57 100644
--- a/drivers/usb/host/ehci-atmel.c
+++ b/drivers/usb/host/ehci-atmel.c
@@ -205,7 +205,8 @@ static int __maybe_unused ehci_atmel_drv_resume(struct device *dev)
 	struct atmel_ehci_priv *atmel_ehci = hcd_to_atmel_ehci_priv(hcd);
 
 	atmel_start_clock(atmel_ehci);
-	return ehci_resume(hcd, false);
+	ehci_resume(hcd, false);
+	return 0;
 }
 
 #ifdef CONFIG_OF
-- 
2.11.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v3 6/8] pwm: atmel-tcb: Support backup mode

[Romain Izard]

Save and restore registers for the PWM on suspend and resume, which
makes hibernation and backup modes possible.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/pwm/pwm-atmel-tcb.c | 63 +++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 61 insertions(+), 2 deletions(-)

diff --git a/drivers/pwm/pwm-atmel-tcb.c b/drivers/pwm/pwm-atmel-tcb.c
index 75db585a2a94..acd3ce8ecf3f 100644
--- a/drivers/pwm/pwm-atmel-tcb.c
+++ b/drivers/pwm/pwm-atmel-tcb.c
@@ -37,11 +37,20 @@ struct atmel_tcb_pwm_device {
 	unsigned period;		/* PWM period expressed in clk cycles */
 };
 
+struct atmel_tcb_channel {
+	u32 enabled;
+	u32 cmr;
+	u32 ra;
+	u32 rb;
+	u32 rc;
+};
+
 struct atmel_tcb_pwm_chip {
 	struct pwm_chip chip;
 	spinlock_t lock;
 	struct atmel_tc *tc;
 	struct atmel_tcb_pwm_device *pwms[NPWM];
+	struct atmel_tcb_channel bkup[NPWM / 2];
 };
 
 static inline struct atmel_tcb_pwm_chip *to_tcb_chip(struct pwm_chip *chip)
@@ -175,12 +184,15 @@ static void atmel_tcb_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 	 * Use software trigger to apply the new setting.
 	 * If both PWM devices in this group are disabled we stop the clock.
 	 */
-	if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC)))
+	if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC))) {
 		__raw_writel(ATMEL_TC_SWTRG | ATMEL_TC_CLKDIS,
 			     regs + ATMEL_TC_REG(group, CCR));
-	else
+		tcbpwmc->bkup[group].enabled = 1;
+	} else {
 		__raw_writel(ATMEL_TC_SWTRG, regs +
 			     ATMEL_TC_REG(group, CCR));
+		tcbpwmc->bkup[group].enabled = 0;
+	}
 
 	spin_unlock(&tcbpwmc->lock);
 }
@@ -263,6 +275,7 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 	/* Use software trigger to apply the new setting */
 	__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
 		     regs + ATMEL_TC_REG(group, CCR));
+	tcbpwmc->bkup[group].enabled = 1;
 	spin_unlock(&tcbpwmc->lock);
 	return 0;
 }
@@ -445,10 +458,56 @@ static const struct of_device_id atmel_tcb_pwm_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, atmel_tcb_pwm_dt_ids);
 
+#ifdef CONFIG_PM_SLEEP
+static int atmel_tcb_pwm_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+	void __iomem *base = tcbpwm->tc->regs;
+	int i;
+
+	for (i = 0; i < (NPWM / 2); i++) {
+		struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+		chan->cmr = readl(base + ATMEL_TC_REG(i, CMR));
+		chan->ra = readl(base + ATMEL_TC_REG(i, RA));
+		chan->rb = readl(base + ATMEL_TC_REG(i, RB));
+		chan->rc = readl(base + ATMEL_TC_REG(i, RC));
+	}
+	return 0;
+}
+
+static int atmel_tcb_pwm_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+	void __iomem *base = tcbpwm->tc->regs;
+	int i;
+
+	for (i = 0; i < (NPWM / 2); i++) {
+		struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+		writel(chan->cmr, base + ATMEL_TC_REG(i, CMR));
+		writel(chan->ra, base + ATMEL_TC_REG(i, RA));
+		writel(chan->rb, base + ATMEL_TC_REG(i, RB));
+		writel(chan->rc, base + ATMEL_TC_REG(i, RC));
+		if (chan->enabled) {
+			writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+				base + ATMEL_TC_REG(i, CCR));
+		}
+	}
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(atmel_tcb_pwm_pm_ops, atmel_tcb_pwm_suspend,
+			 atmel_tcb_pwm_resume);
+
 static struct platform_driver atmel_tcb_pwm_driver = {
 	.driver = {
 		.name = "atmel-tcb-pwm",
 		.of_match_table = atmel_tcb_pwm_dt_ids,
+		.pm = &atmel_tcb_pwm_pm_ops,
 	},
 	.probe = atmel_tcb_pwm_probe,
 	.remove = atmel_tcb_pwm_remove,
-- 
2.11.0

[PATCH v3 6/8] pwm: atmel-tcb: Support backup mode

[Romain Izard]

Save and restore registers for the PWM on suspend and resume, which
makes hibernation and backup modes possible.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/pwm/pwm-atmel-tcb.c | 63 +++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 61 insertions(+), 2 deletions(-)

diff --git a/drivers/pwm/pwm-atmel-tcb.c b/drivers/pwm/pwm-atmel-tcb.c
index 75db585a2a94..acd3ce8ecf3f 100644
--- a/drivers/pwm/pwm-atmel-tcb.c
+++ b/drivers/pwm/pwm-atmel-tcb.c
@@ -37,11 +37,20 @@ struct atmel_tcb_pwm_device {
 	unsigned period;		/* PWM period expressed in clk cycles */
 };
 
+struct atmel_tcb_channel {
+	u32 enabled;
+	u32 cmr;
+	u32 ra;
+	u32 rb;
+	u32 rc;
+};
+
 struct atmel_tcb_pwm_chip {
 	struct pwm_chip chip;
 	spinlock_t lock;
 	struct atmel_tc *tc;
 	struct atmel_tcb_pwm_device *pwms[NPWM];
+	struct atmel_tcb_channel bkup[NPWM / 2];
 };
 
 static inline struct atmel_tcb_pwm_chip *to_tcb_chip(struct pwm_chip *chip)
@@ -175,12 +184,15 @@ static void atmel_tcb_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 	 * Use software trigger to apply the new setting.
 	 * If both PWM devices in this group are disabled we stop the clock.
 	 */
-	if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC)))
+	if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC))) {
 		__raw_writel(ATMEL_TC_SWTRG | ATMEL_TC_CLKDIS,
 			     regs + ATMEL_TC_REG(group, CCR));
-	else
+		tcbpwmc->bkup[group].enabled = 1;
+	} else {
 		__raw_writel(ATMEL_TC_SWTRG, regs +
 			     ATMEL_TC_REG(group, CCR));
+		tcbpwmc->bkup[group].enabled = 0;
+	}
 
 	spin_unlock(&tcbpwmc->lock);
 }
@@ -263,6 +275,7 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
 	/* Use software trigger to apply the new setting */
 	__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
 		     regs + ATMEL_TC_REG(group, CCR));
+	tcbpwmc->bkup[group].enabled = 1;
 	spin_unlock(&tcbpwmc->lock);
 	return 0;
 }
@@ -445,10 +458,56 @@ static const struct of_device_id atmel_tcb_pwm_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, atmel_tcb_pwm_dt_ids);
 
+#ifdef CONFIG_PM_SLEEP
+static int atmel_tcb_pwm_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+	void __iomem *base = tcbpwm->tc->regs;
+	int i;
+
+	for (i = 0; i < (NPWM / 2); i++) {
+		struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+		chan->cmr = readl(base + ATMEL_TC_REG(i, CMR));
+		chan->ra = readl(base + ATMEL_TC_REG(i, RA));
+		chan->rb = readl(base + ATMEL_TC_REG(i, RB));
+		chan->rc = readl(base + ATMEL_TC_REG(i, RC));
+	}
+	return 0;
+}
+
+static int atmel_tcb_pwm_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+	void __iomem *base = tcbpwm->tc->regs;
+	int i;
+
+	for (i = 0; i < (NPWM / 2); i++) {
+		struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+		writel(chan->cmr, base + ATMEL_TC_REG(i, CMR));
+		writel(chan->ra, base + ATMEL_TC_REG(i, RA));
+		writel(chan->rb, base + ATMEL_TC_REG(i, RB));
+		writel(chan->rc, base + ATMEL_TC_REG(i, RC));
+		if (chan->enabled) {
+			writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+				base + ATMEL_TC_REG(i, CCR));
+		}
+	}
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(atmel_tcb_pwm_pm_ops, atmel_tcb_pwm_suspend,
+			 atmel_tcb_pwm_resume);
+
 static struct platform_driver atmel_tcb_pwm_driver = {
 	.driver = {
 		.name = "atmel-tcb-pwm",
 		.of_match_table = atmel_tcb_pwm_dt_ids,
+		.pm = &atmel_tcb_pwm_pm_ops,
 	},
 	.probe = atmel_tcb_pwm_probe,
 	.remove = atmel_tcb_pwm_remove,
-- 
2.11.0

[PATCH v3 7/8] atmel_flexcom: Support backup mode

[Romain Izard]

The controller used by a flexcom module is configured at boot, and left
alone after this. As the configuration will be lost after backup mode,
restore the state of the flexcom driver on resume.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/mfd/atmel-flexcom.c | 65 ++++++++++++++++++++++++++++++++++-----------
 1 file changed, 50 insertions(+), 15 deletions(-)

diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
index 064bde9cff5a..ef1235c4a179 100644
--- a/drivers/mfd/atmel-flexcom.c
+++ b/drivers/mfd/atmel-flexcom.c
@@ -39,34 +39,44 @@
 #define FLEX_MR_OPMODE(opmode)	(((opmode) << FLEX_MR_OPMODE_OFFSET) &	\
 				 FLEX_MR_OPMODE_MASK)
 
+struct atmel_flexcom {
+	void __iomem *base;
+	u32 opmode;
+	struct clk *clk;
+};
 
 static int atmel_flexcom_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
-	struct clk *clk;
 	struct resource *res;
-	void __iomem *base;
-	u32 opmode;
+	struct atmel_flexcom *afc;
 	int err;
+	u32 val;
+
+	afc = devm_kzalloc(&pdev->dev, sizeof(*afc), GFP_KERNEL);
+	if (!afc)
+		return -ENOMEM;
 
-	err = of_property_read_u32(np, "atmel,flexcom-mode", &opmode);
+	platform_set_drvdata(pdev, afc);
+
+	err = of_property_read_u32(np, "atmel,flexcom-mode", &afc->opmode);
 	if (err)
 		return err;
 
-	if (opmode < ATMEL_FLEXCOM_MODE_USART ||
-	    opmode > ATMEL_FLEXCOM_MODE_TWI)
+	if (afc->opmode < ATMEL_FLEXCOM_MODE_USART ||
+	    afc->opmode > ATMEL_FLEXCOM_MODE_TWI)
 		return -EINVAL;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	afc->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(afc->base))
+		return PTR_ERR(afc->base);
 
-	clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
+	afc->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(afc->clk))
+		return PTR_ERR(afc->clk);
 
-	err = clk_prepare_enable(clk);
+	err = clk_prepare_enable(afc->clk);
 	if (err)
 		return err;
 
@@ -76,9 +86,10 @@ static int atmel_flexcom_probe(struct platform_device *pdev)
 	 * inaccessible and are read as zero. Also the external I/O lines of the
 	 * Flexcom are muxed to reach the selected device.
 	 */
-	writel(FLEX_MR_OPMODE(opmode), base + FLEX_MR);
+	val = FLEX_MR_OPMODE(afc->opmode);
+	writel(val, afc->base + FLEX_MR);
 
-	clk_disable_unprepare(clk);
+	clk_disable_unprepare(afc->clk);
 
 	return devm_of_platform_populate(&pdev->dev);
 }
@@ -89,10 +100,34 @@ static const struct of_device_id atmel_flexcom_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
 
+#ifdef CONFIG_PM_SLEEP
+static int atmel_flexcom_resume(struct device *dev)
+{
+	struct atmel_flexcom *afc = dev_get_drvdata(dev);
+	int err;
+	u32 val;
+
+	err = clk_prepare_enable(afc->clk);
+	if (err)
+		return err;
+
+	val = FLEX_MR_OPMODE(afc->opmode),
+	writel(val, afc->base + FLEX_MR);
+
+	clk_disable_unprepare(afc->clk);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(atmel_flexcom_pm_ops, NULL,
+			 atmel_flexcom_resume);
+
 static struct platform_driver atmel_flexcom_driver = {
 	.probe	= atmel_flexcom_probe,
 	.driver	= {
 		.name		= "atmel_flexcom",
+		.pm		= &atmel_flexcom_pm_ops,
 		.of_match_table	= atmel_flexcom_of_match,
 	},
 };
-- 
2.11.0

[PATCH v3 7/8] atmel_flexcom: Support backup mode

[Romain Izard]

The controller used by a flexcom module is configured at boot, and left
alone after this. As the configuration will be lost after backup mode,
restore the state of the flexcom driver on resume.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 drivers/mfd/atmel-flexcom.c | 65 ++++++++++++++++++++++++++++++++++-----------
 1 file changed, 50 insertions(+), 15 deletions(-)

diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
index 064bde9cff5a..ef1235c4a179 100644
--- a/drivers/mfd/atmel-flexcom.c
+++ b/drivers/mfd/atmel-flexcom.c
@@ -39,34 +39,44 @@
 #define FLEX_MR_OPMODE(opmode)	(((opmode) << FLEX_MR_OPMODE_OFFSET) &	\
 				 FLEX_MR_OPMODE_MASK)
 
+struct atmel_flexcom {
+	void __iomem *base;
+	u32 opmode;
+	struct clk *clk;
+};
 
 static int atmel_flexcom_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
-	struct clk *clk;
 	struct resource *res;
-	void __iomem *base;
-	u32 opmode;
+	struct atmel_flexcom *afc;
 	int err;
+	u32 val;
+
+	afc = devm_kzalloc(&pdev->dev, sizeof(*afc), GFP_KERNEL);
+	if (!afc)
+		return -ENOMEM;
 
-	err = of_property_read_u32(np, "atmel,flexcom-mode", &opmode);
+	platform_set_drvdata(pdev, afc);
+
+	err = of_property_read_u32(np, "atmel,flexcom-mode", &afc->opmode);
 	if (err)
 		return err;
 
-	if (opmode < ATMEL_FLEXCOM_MODE_USART ||
-	    opmode > ATMEL_FLEXCOM_MODE_TWI)
+	if (afc->opmode < ATMEL_FLEXCOM_MODE_USART ||
+	    afc->opmode > ATMEL_FLEXCOM_MODE_TWI)
 		return -EINVAL;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	afc->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(afc->base))
+		return PTR_ERR(afc->base);
 
-	clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
+	afc->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(afc->clk))
+		return PTR_ERR(afc->clk);
 
-	err = clk_prepare_enable(clk);
+	err = clk_prepare_enable(afc->clk);
 	if (err)
 		return err;
 
@@ -76,9 +86,10 @@ static int atmel_flexcom_probe(struct platform_device *pdev)
 	 * inaccessible and are read as zero. Also the external I/O lines of the
 	 * Flexcom are muxed to reach the selected device.
 	 */
-	writel(FLEX_MR_OPMODE(opmode), base + FLEX_MR);
+	val = FLEX_MR_OPMODE(afc->opmode);
+	writel(val, afc->base + FLEX_MR);
 
-	clk_disable_unprepare(clk);
+	clk_disable_unprepare(afc->clk);
 
 	return devm_of_platform_populate(&pdev->dev);
 }
@@ -89,10 +100,34 @@ static const struct of_device_id atmel_flexcom_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
 
+#ifdef CONFIG_PM_SLEEP
+static int atmel_flexcom_resume(struct device *dev)
+{
+	struct atmel_flexcom *afc = dev_get_drvdata(dev);
+	int err;
+	u32 val;
+
+	err = clk_prepare_enable(afc->clk);
+	if (err)
+		return err;
+
+	val = FLEX_MR_OPMODE(afc->opmode),
+	writel(val, afc->base + FLEX_MR);
+
+	clk_disable_unprepare(afc->clk);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(atmel_flexcom_pm_ops, NULL,
+			 atmel_flexcom_resume);
+
 static struct platform_driver atmel_flexcom_driver = {
 	.probe	= atmel_flexcom_probe,
 	.driver	= {
 		.name		= "atmel_flexcom",
+		.pm		= &atmel_flexcom_pm_ops,
 		.of_match_table	= atmel_flexcom_of_match,
 	},
 };
-- 
2.11.0

[PATCH v3 8/8] tty/serial: atmel: Prevent a warning on suspend

[Romain Izard]

The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter

As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.

After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.

Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
---
 drivers/tty/serial/atmel_serial.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 7551cab438ff..ce45b4ada0bf 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -171,6 +171,7 @@ struct atmel_uart_port {
 	bool			has_hw_timer;
 	struct timer_list	uart_timer;
 
+	bool			tx_stopped;
 	bool			suspended;
 	unsigned int		pending;
 	unsigned int		pending_status;
@@ -380,6 +381,10 @@ static int atmel_config_rs485(struct uart_port *port,
  */
 static u_int atmel_tx_empty(struct uart_port *port)
 {
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+	if (atmel_port->tx_stopped)
+		return TIOCSER_TEMT;
 	return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
 		TIOCSER_TEMT :
 		0;
@@ -485,6 +490,7 @@ static void atmel_stop_tx(struct uart_port *port)
 	 * is fully transmitted.
 	 */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
+	atmel_port->tx_stopped = true;
 
 	/* Disable interrupts */
 	atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
@@ -521,6 +527,7 @@ static void atmel_start_tx(struct uart_port *port)
 
 	/* re-enable the transmitter */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+	atmel_port->tx_stopped = false;
 }
 
 /*
@@ -1866,6 +1873,7 @@ static int atmel_startup(struct uart_port *port)
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	/* enable xmit & rcvr */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	setup_timer(&atmel_port->uart_timer,
 			atmel_uart_timer_callback,
@@ -2122,6 +2130,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	/* disable receiver and transmitter */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
+	atmel_port->tx_stopped = true;
 
 	/* mode */
 	if (port->rs485.flags & SER_RS485_ENABLED) {
@@ -2207,6 +2216,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 	atmel_uart_writel(port, ATMEL_US_BRGR, quot);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	/* restore interrupts */
 	atmel_uart_writel(port, ATMEL_US_IER, imr);
@@ -2450,6 +2460,7 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
 
 	/* Make sure that tx path is actually able to send characters */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+	atmel_port->tx_stopped = false;
 
 	uart_console_write(port, s, count, atmel_console_putchar);
 
@@ -2511,6 +2522,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
 {
 	int ret;
 	struct uart_port *port = &atmel_ports[co->index].uart;
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 	int baud = 115200;
 	int bits = 8;
 	int parity = 'n';
@@ -2528,6 +2540,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
 	atmel_uart_writel(port, ATMEL_US_IDR, -1);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
-- 
2.11.0

[PATCH v3 8/8] tty/serial: atmel: Prevent a warning on suspend

[Romain Izard]

The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter

As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.

After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.

Signed-off-by: Romain Izard <romain.izard.pro-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Tested-by: Nicolas Ferre <nicolas.ferre-UWL1GkI3JZL3oGB3hsPCZA@public.gmane.org>
Acked-by: Nicolas Ferre <nicolas.ferre-UWL1GkI3JZL3oGB3hsPCZA@public.gmane.org>
Acked-by: Richard Genoud <richard.genoud-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 drivers/tty/serial/atmel_serial.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 7551cab438ff..ce45b4ada0bf 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -171,6 +171,7 @@ struct atmel_uart_port {
 	bool			has_hw_timer;
 	struct timer_list	uart_timer;
 
+	bool			tx_stopped;
 	bool			suspended;
 	unsigned int		pending;
 	unsigned int		pending_status;
@@ -380,6 +381,10 @@ static int atmel_config_rs485(struct uart_port *port,
  */
 static u_int atmel_tx_empty(struct uart_port *port)
 {
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+	if (atmel_port->tx_stopped)
+		return TIOCSER_TEMT;
 	return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
 		TIOCSER_TEMT :
 		0;
@@ -485,6 +490,7 @@ static void atmel_stop_tx(struct uart_port *port)
 	 * is fully transmitted.
 	 */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
+	atmel_port->tx_stopped = true;
 
 	/* Disable interrupts */
 	atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
@@ -521,6 +527,7 @@ static void atmel_start_tx(struct uart_port *port)
 
 	/* re-enable the transmitter */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+	atmel_port->tx_stopped = false;
 }
 
 /*
@@ -1866,6 +1873,7 @@ static int atmel_startup(struct uart_port *port)
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	/* enable xmit & rcvr */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	setup_timer(&atmel_port->uart_timer,
 			atmel_uart_timer_callback,
@@ -2122,6 +2130,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	/* disable receiver and transmitter */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
+	atmel_port->tx_stopped = true;
 
 	/* mode */
 	if (port->rs485.flags & SER_RS485_ENABLED) {
@@ -2207,6 +2216,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 	atmel_uart_writel(port, ATMEL_US_BRGR, quot);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	/* restore interrupts */
 	atmel_uart_writel(port, ATMEL_US_IER, imr);
@@ -2450,6 +2460,7 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
 
 	/* Make sure that tx path is actually able to send characters */
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+	atmel_port->tx_stopped = false;
 
 	uart_console_write(port, s, count, atmel_console_putchar);
 
@@ -2511,6 +2522,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
 {
 	int ret;
 	struct uart_port *port = &atmel_ports[co->index].uart;
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
 	int baud = 115200;
 	int bits = 8;
 	int parity = 'n';
@@ -2528,6 +2540,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
 	atmel_uart_writel(port, ATMEL_US_IDR, -1);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
 	atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+	atmel_port->tx_stopped = false;
 
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html