* [PATCH] ARM: dts: imx6ul: Remove leading zeroes from unit addresses
@ 2017-09-21 17:01 Marco Franchi
[not found] ` <1506013285-31170-1-git-send-email-marco.franchi-3arQi8VN3Tc@public.gmane.org>
0 siblings, 1 reply; 2+ messages in thread
From: Marco Franchi @ 2017-09-21 17:01 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWPLiZjB17Co1B2eb7JE58TQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
festevam-Re5JQEeQqe8AvxtiuMwx3w, marcofrk-Re5JQEeQqe8AvxtiuMwx3w,
Marco Franchi
The following build warnings are seen with W=1:
Warning (unit_address_format): Node /interrupt-controller@00a01000 unit
name should not have leading 0s
Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit address
format error, expected "900000"
Warning (simple_bus_reg): Node /soc/dma-apbh@01804000 simple-bus unit
address format error, expected "1804000"
(...)
Remove the leading zeroes from unit addresses to fix the warnings.
Signed-off-by: Marco Franchi <marco.franchi-3arQi8VN3Tc@public.gmane.org>
---
arch/arm/boot/dts/imx6ul.dtsi | 142 +++++++++++++++++++++---------------------
1 file changed, 71 insertions(+), 71 deletions(-)
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index f11a241..2057ee6 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -98,7 +98,7 @@
};
};
- intc: interrupt-controller@00a01000 {
+ intc: interrupt-controller@a01000 {
compatible = "arm,gic-400", "arm,cortex-a7-gic";
#interrupt-cells = <3>;
interrupt-controller;
@@ -149,12 +149,12 @@
status = "disabled";
};
- ocram: sram@00900000 {
+ ocram: sram@900000 {
compatible = "mmio-sram";
reg = <0x00900000 0x20000>;
};
- dma_apbh: dma-apbh@01804000 {
+ dma_apbh: dma-apbh@1804000 {
compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
reg = <0x01804000 0x2000>;
interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
@@ -167,7 +167,7 @@
clocks = <&clks IMX6UL_CLK_APBHDMA>;
};
- gpmi: gpmi-nand@01806000 {
+ gpmi: gpmi-nand@1806000 {
compatible = "fsl,imx6q-gpmi-nand";
#address-cells = <1>;
#size-cells = <1>;
@@ -187,21 +187,21 @@
status = "disabled";
};
- aips1: aips-bus@02000000 {
+ aips1: aips-bus@2000000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x02000000 0x100000>;
ranges;
- spba-bus@02000000 {
+ spba-bus@2000000 {
compatible = "fsl,spba-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x02000000 0x40000>;
ranges;
- ecspi1: ecspi@02008000 {
+ ecspi1: ecspi@2008000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
@@ -213,7 +213,7 @@
status = "disabled";
};
- ecspi2: ecspi@0200c000 {
+ ecspi2: ecspi@200c000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
@@ -225,7 +225,7 @@
status = "disabled";
};
- ecspi3: ecspi@02010000 {
+ ecspi3: ecspi@2010000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
@@ -237,7 +237,7 @@
status = "disabled";
};
- ecspi4: ecspi@02014000 {
+ ecspi4: ecspi@2014000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
@@ -249,7 +249,7 @@
status = "disabled";
};
- uart7: serial@02018000 {
+ uart7: serial@2018000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x02018000 0x4000>;
@@ -260,7 +260,7 @@
status = "disabled";
};
- uart1: serial@02020000 {
+ uart1: serial@2020000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x02020000 0x4000>;
@@ -271,7 +271,7 @@
status = "disabled";
};
- uart8: serial@02024000 {
+ uart8: serial@2024000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x02024000 0x4000>;
@@ -282,7 +282,7 @@
status = "disabled";
};
- sai1: sai@02028000 {
+ sai1: sai@2028000 {
#sound-dai-cells = <0>;
compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
reg = <0x02028000 0x4000>;
@@ -297,7 +297,7 @@
status = "disabled";
};
- sai2: sai@0202c000 {
+ sai2: sai@202c000 {
#sound-dai-cells = <0>;
compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
reg = <0x0202c000 0x4000>;
@@ -312,7 +312,7 @@
status = "disabled";
};
- sai3: sai@02030000 {
+ sai3: sai@2030000 {
#sound-dai-cells = <0>;
compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
reg = <0x02030000 0x4000>;
@@ -328,7 +328,7 @@
};
};
- tsc: tsc@02040000 {
+ tsc: tsc@2040000 {
compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
@@ -339,7 +339,7 @@
status = "disabled";
};
- pwm1: pwm@02080000 {
+ pwm1: pwm@2080000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x02080000 0x4000>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
@@ -350,7 +350,7 @@
status = "disabled";
};
- pwm2: pwm@02084000 {
+ pwm2: pwm@2084000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x02084000 0x4000>;
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
@@ -361,7 +361,7 @@
status = "disabled";
};
- pwm3: pwm@02088000 {
+ pwm3: pwm@2088000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x02088000 0x4000>;
interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
@@ -372,7 +372,7 @@
status = "disabled";
};
- pwm4: pwm@0208c000 {
+ pwm4: pwm@208c000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x0208c000 0x4000>;
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
@@ -383,7 +383,7 @@
status = "disabled";
};
- can1: flexcan@02090000 {
+ can1: flexcan@2090000 {
compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
reg = <0x02090000 0x4000>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -393,7 +393,7 @@
status = "disabled";
};
- can2: flexcan@02094000 {
+ can2: flexcan@2094000 {
compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
reg = <0x02094000 0x4000>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -403,7 +403,7 @@
status = "disabled";
};
- gpt1: gpt@02098000 {
+ gpt1: gpt@2098000 {
compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
reg = <0x02098000 0x4000>;
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -412,7 +412,7 @@
clock-names = "ipg", "per";
};
- gpio1: gpio@0209c000 {
+ gpio1: gpio@209c000 {
compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
reg = <0x0209c000 0x4000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
@@ -425,7 +425,7 @@
<&iomuxc 16 33 16>;
};
- gpio2: gpio@020a0000 {
+ gpio2: gpio@20a0000 {
compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
reg = <0x020a0000 0x4000>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
@@ -437,7 +437,7 @@
gpio-ranges = <&iomuxc 0 49 16>, <&iomuxc 16 111 6>;
};
- gpio3: gpio@020a4000 {
+ gpio3: gpio@20a4000 {
compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
reg = <0x020a4000 0x4000>;
interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
@@ -449,7 +449,7 @@
gpio-ranges = <&iomuxc 0 65 29>;
};
- gpio4: gpio@020a8000 {
+ gpio4: gpio@20a8000 {
compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
reg = <0x020a8000 0x4000>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
@@ -461,7 +461,7 @@
gpio-ranges = <&iomuxc 0 94 17>, <&iomuxc 17 117 12>;
};
- gpio5: gpio@020ac000 {
+ gpio5: gpio@20ac000 {
compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
reg = <0x020ac000 0x4000>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
@@ -473,7 +473,7 @@
gpio-ranges = <&iomuxc 0 7 10>, <&iomuxc 10 5 2>;
};
- fec2: ethernet@020b4000 {
+ fec2: ethernet@20b4000 {
compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
reg = <0x020b4000 0x4000>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
@@ -490,7 +490,7 @@
status = "disabled";
};
- kpp: kpp@020b8000 {
+ kpp: kpp@20b8000 {
compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
reg = <0x020b8000 0x4000>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -498,14 +498,14 @@
status = "disabled";
};
- wdog1: wdog@020bc000 {
+ wdog1: wdog@20bc000 {
compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
reg = <0x020bc000 0x4000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6UL_CLK_WDOG1>;
};
- wdog2: wdog@020c0000 {
+ wdog2: wdog@20c0000 {
compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
reg = <0x020c0000 0x4000>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
@@ -513,7 +513,7 @@
status = "disabled";
};
- clks: ccm@020c4000 {
+ clks: ccm@20c4000 {
compatible = "fsl,imx6ul-ccm";
reg = <0x020c4000 0x4000>;
interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -523,7 +523,7 @@
clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
};
- anatop: anatop@020c8000 {
+ anatop: anatop@20c8000 {
compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
"syscon", "simple-bus";
reg = <0x020c8000 0x1000>;
@@ -580,7 +580,7 @@
};
};
- usbphy1: usbphy@020c9000 {
+ usbphy1: usbphy@20c9000 {
compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
reg = <0x020c9000 0x1000>;
interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
@@ -589,7 +589,7 @@
fsl,anatop = <&anatop>;
};
- usbphy2: usbphy@020ca000 {
+ usbphy2: usbphy@20ca000 {
compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
reg = <0x020ca000 0x1000>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
@@ -598,7 +598,7 @@
fsl,anatop = <&anatop>;
};
- snvs: snvs@020cc000 {
+ snvs: snvs@20cc000 {
compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
reg = <0x020cc000 0x4000>;
@@ -628,17 +628,17 @@
};
};
- epit1: epit@020d0000 {
+ epit1: epit@20d0000 {
reg = <0x020d0000 0x4000>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
};
- epit2: epit@020d4000 {
+ epit2: epit@20d4000 {
reg = <0x020d4000 0x4000>;
interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
};
- src: src@020d8000 {
+ src: src@20d8000 {
compatible = "fsl,imx6ul-src", "fsl,imx51-src";
reg = <0x020d8000 0x4000>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -646,7 +646,7 @@
#reset-cells = <1>;
};
- gpc: gpc@020dc000 {
+ gpc: gpc@20dc000 {
compatible = "fsl,imx6ul-gpc", "fsl,imx6q-gpc";
reg = <0x020dc000 0x4000>;
interrupt-controller;
@@ -655,18 +655,18 @@
interrupt-parent = <&intc>;
};
- iomuxc: iomuxc@020e0000 {
+ iomuxc: iomuxc@20e0000 {
compatible = "fsl,imx6ul-iomuxc";
reg = <0x020e0000 0x4000>;
};
- gpr: iomuxc-gpr@020e4000 {
+ gpr: iomuxc-gpr@20e4000 {
compatible = "fsl,imx6ul-iomuxc-gpr",
"fsl,imx6q-iomuxc-gpr", "syscon";
reg = <0x020e4000 0x4000>;
};
- gpt2: gpt@020e8000 {
+ gpt2: gpt@20e8000 {
compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
reg = <0x020e8000 0x4000>;
interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
@@ -675,7 +675,7 @@
clock-names = "ipg", "per";
};
- sdma: sdma@020ec000 {
+ sdma: sdma@20ec000 {
compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
"fsl,imx35-sdma";
reg = <0x020ec000 0x4000>;
@@ -687,7 +687,7 @@
fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
};
- pwm5: pwm@020f0000 {
+ pwm5: pwm@20f0000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x020f0000 0x4000>;
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
@@ -698,7 +698,7 @@
status = "disabled";
};
- pwm6: pwm@020f4000 {
+ pwm6: pwm@20f4000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x020f4000 0x4000>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
@@ -709,7 +709,7 @@
status = "disabled";
};
- pwm7: pwm@020f8000 {
+ pwm7: pwm@20f8000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x020f8000 0x4000>;
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
@@ -720,7 +720,7 @@
status = "disabled";
};
- pwm8: pwm@020fc000 {
+ pwm8: pwm@20fc000 {
compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
reg = <0x020fc000 0x4000>;
interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
@@ -732,14 +732,14 @@
};
};
- aips2: aips-bus@02100000 {
+ aips2: aips-bus@2100000 {
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x02100000 0x100000>;
ranges;
- usbotg1: usb@02184000 {
+ usbotg1: usb@2184000 {
compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
reg = <0x02184000 0x200>;
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
@@ -753,7 +753,7 @@
status = "disabled";
};
- usbotg2: usb@02184200 {
+ usbotg2: usb@2184200 {
compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
reg = <0x02184200 0x200>;
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
@@ -766,13 +766,13 @@
status = "disabled";
};
- usbmisc: usbmisc@02184800 {
+ usbmisc: usbmisc@2184800 {
#index-cells = <1>;
compatible = "fsl,imx6ul-usbmisc", "fsl,imx6q-usbmisc";
reg = <0x02184800 0x200>;
};
- fec1: ethernet@02188000 {
+ fec1: ethernet@2188000 {
compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
reg = <0x02188000 0x4000>;
interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
@@ -789,7 +789,7 @@
status = "disabled";
};
- usdhc1: usdhc@02190000 {
+ usdhc1: usdhc@2190000 {
compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
reg = <0x02190000 0x4000>;
interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -801,7 +801,7 @@
status = "disabled";
};
- usdhc2: usdhc@02194000 {
+ usdhc2: usdhc@2194000 {
compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
reg = <0x02194000 0x4000>;
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -813,7 +813,7 @@
status = "disabled";
};
- adc1: adc@02198000 {
+ adc1: adc@2198000 {
compatible = "fsl,imx6ul-adc", "fsl,vf610-adc";
reg = <0x02198000 0x4000>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
@@ -825,7 +825,7 @@
status = "disabled";
};
- i2c1: i2c@021a0000 {
+ i2c1: i2c@21a0000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
@@ -835,7 +835,7 @@
status = "disabled";
};
- i2c2: i2c@021a4000 {
+ i2c2: i2c@21a4000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
@@ -845,7 +845,7 @@
status = "disabled";
};
- i2c3: i2c@021a8000 {
+ i2c3: i2c@21a8000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
@@ -855,18 +855,18 @@
status = "disabled";
};
- mmdc: mmdc@021b0000 {
+ mmdc: mmdc@21b0000 {
compatible = "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc";
reg = <0x021b0000 0x4000>;
};
- ocotp: ocotp-ctrl@021bc000 {
+ ocotp: ocotp-ctrl@21bc000 {
compatible = "fsl,imx6ul-ocotp", "syscon";
reg = <0x021bc000 0x4000>;
clocks = <&clks IMX6UL_CLK_OCOTP>;
};
- lcdif: lcdif@021c8000 {
+ lcdif: lcdif@21c8000 {
compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
reg = <0x021c8000 0x4000>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
@@ -877,7 +877,7 @@
status = "disabled";
};
- qspi: qspi@021e0000 {
+ qspi: qspi@21e0000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
@@ -890,7 +890,7 @@
status = "disabled";
};
- uart2: serial@021e8000 {
+ uart2: serial@21e8000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x021e8000 0x4000>;
@@ -901,7 +901,7 @@
status = "disabled";
};
- uart3: serial@021ec000 {
+ uart3: serial@21ec000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x021ec000 0x4000>;
@@ -912,7 +912,7 @@
status = "disabled";
};
- uart4: serial@021f0000 {
+ uart4: serial@21f0000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x021f0000 0x4000>;
@@ -923,7 +923,7 @@
status = "disabled";
};
- uart5: serial@021f4000 {
+ uart5: serial@21f4000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x021f4000 0x4000>;
@@ -934,7 +934,7 @@
status = "disabled";
};
- i2c4: i2c@021f8000 {
+ i2c4: i2c@21f8000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
@@ -944,7 +944,7 @@
status = "disabled";
};
- uart6: serial@021fc000 {
+ uart6: serial@21fc000 {
compatible = "fsl,imx6ul-uart",
"fsl,imx6q-uart";
reg = <0x021fc000 0x4000>;
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] ARM: dts: imx6ul: Remove leading zeroes from unit addresses
[not found] ` <1506013285-31170-1-git-send-email-marco.franchi-3arQi8VN3Tc@public.gmane.org>
@ 2017-10-13 4:53 ` Shawn Guo
0 siblings, 0 replies; 2+ messages in thread
From: Shawn Guo @ 2017-10-13 4:53 UTC (permalink / raw)
To: Marco Franchi
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWPLiZjB17Co1B2eb7JE58TQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
festevam-Re5JQEeQqe8AvxtiuMwx3w, marcofrk-Re5JQEeQqe8AvxtiuMwx3w
On Thu, Sep 21, 2017 at 02:01:25PM -0300, Marco Franchi wrote:
> The following build warnings are seen with W=1:
>
> Warning (unit_address_format): Node /interrupt-controller@00a01000 unit
> name should not have leading 0s
> Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit address
> format error, expected "900000"
> Warning (simple_bus_reg): Node /soc/dma-apbh@01804000 simple-bus unit
> address format error, expected "1804000"
> (...)
>
> Remove the leading zeroes from unit addresses to fix the warnings.
>
> Signed-off-by: Marco Franchi <marco.franchi-3arQi8VN3Tc@public.gmane.org>
Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2017-10-13 4:53 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-09-21 17:01 [PATCH] ARM: dts: imx6ul: Remove leading zeroes from unit addresses Marco Franchi
[not found] ` <1506013285-31170-1-git-send-email-marco.franchi-3arQi8VN3Tc@public.gmane.org>
2017-10-13 4:53 ` Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.