From: Francisco Iglesias <frasse.iglesias@gmail.com>
To: qemu-devel@nongnu.org
Cc: edgari@xilinx.com, alistai@xilinx.com,
francisco.iglesias@feimtech.se, mar.krzeminski@gmail.com,
peter.maydell@linaro.org
Subject: [Qemu-devel] [PATCH v7 00/13] Add support for the ZynqMP Generic QSPI
Date: Fri, 3 Nov 2017 01:00:56 +0100 [thread overview]
Message-ID: <20171103000109.28244-1-frasse.iglesias@gmail.com> (raw)
Hi,
This patch series is an attempt to add support for the ZynqMP QSPI (consisting
of the Generic QSPI and the legacy QSPI) to the xlnx-zcu102 board and connect
Numonyx n25q512a11 flashes to the QSPI. Also some functionality is added to
m25p80.
The series starts by adding support in m25p80 for continous read out of status
registers, SST flash READ ID commands, bank address register accesses, bulk
erase (0x60) and two Numonyx flashes (n25q512a11 and n25q512a13). Thereafter it
updates the striping behaviour to be bit big endiann in the Xilinx QSPI model
and adds support for RX discard, zero pumping according transfer register and 4
byte LQSPI addresses. Finally it adds support for the ZynqMP Generic QSPI and
adds the ZynqMP QSPI to the xlnx-zcu102 board.
Best regards,
Francisco Iglesias
Changelog:
v6 -> v7
* Moved data_read_loop into a vmstate subsection in patch 'm25p80: Add support
for continuous read out of RDSR and READ_FSR' for not breaking compatibility
against older vmstate versions unless necessary.
* Minor tweaks in patch 'xilinx_spips: Add support for the ZynqMP Generic
QSPI'.
v5 -> v6
* Added data_read_loop to vmstate_m25p80 in patch 'm25p80: Add support for
continuous read out of RDSR and READ_FSR'. Also removed acked-by lines in
the commit message because of this update.
* Reworked patch 'xilinx_spips: Add support for the ZynqMP Generic QSPI'.
* Tweaked commit messages
v4 -> v5
* Added newlines in patch 'xlnx-zcu102: Add support for the ZynqMP QSPI'
v3 -> v4
* Corrected patch 'Add support for SST READ ID 0x90/0xAB commands'
* Corrected patch 'Add support Add support for BRRD/BRWR and BULK_ERASE'
* Minor tweaks in the ZynqMP GQSPI patch for reducing the patch
v2 -> v3
* Tweaked commit messages
* Corrected patch 08 'Make tx/rx_data_bytes more generic and reusable'
* Reworked the patch adding the ZynqMP GQSPI and splitted out another QSPI
related change into an own patch 'Don't set TX FIFO UNDERFLOW at cmd done'
v1 -> v2
* Reset author on commits (due to mailing issues).
Francisco Iglesias (13):
m25p80: Add support for continuous read out of RDSR and READ_FSR
m25p80: Add support for SST READ ID 0x90/0xAB commands
m25p80: Add support for BRRD/BRWR and BULK_ERASE (0x60)
m25p80: Add support for n25q512a11 and n25q512a13
xilinx_spips: Move FlashCMD, XilinxQSPIPS and XilinxSPIPSClass
xilinx_spips: Update striping to be big-endian bit order
xilinx_spips: Add support for RX discard and RX drain
xilinx_spips: Make tx/rx_data_bytes more generic and reusable
xilinx_spips: Add support for zero pumping
xilinx_spips: Add support for 4 byte addresses in the LQSPI
xilinx_spips: Don't set TX FIFO UNDERFLOW at cmd done
xilinx_spips: Add support for the ZynqMP Generic QSPI
xlnx-zcu102: Add support for the ZynqMP QSPI
default-configs/arm-softmmu.mak | 1 +
hw/arm/xlnx-zcu102.c | 23 +
hw/arm/xlnx-zynqmp.c | 26 ++
hw/block/m25p80.c | 71 +++-
hw/ssi/xilinx_spips.c | 899 ++++++++++++++++++++++++++++++++++------
include/hw/arm/xlnx-zynqmp.h | 5 +
include/hw/ssi/xilinx_spips.h | 74 +++-
7 files changed, 961 insertions(+), 138 deletions(-)
--
2.9.3
next reply other threads:[~2017-11-03 0:01 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-11-03 0:00 Francisco Iglesias [this message]
2017-11-03 0:00 ` [Qemu-devel] [PATCH v7 01/13] m25p80: Add support for continuous read out of RDSR and READ_FSR Francisco Iglesias
2017-11-03 16:18 ` mar.krzeminski
2017-11-03 17:25 ` francisco iglesias
2017-11-03 20:34 ` mar.krzeminski
2017-11-03 0:00 ` [Qemu-devel] [PATCH v7 02/13] m25p80: Add support for SST READ ID 0x90/0xAB commands Francisco Iglesias
2017-11-03 0:00 ` [Qemu-devel] [PATCH v7 03/13] m25p80: Add support for BRRD/BRWR and BULK_ERASE (0x60) Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 04/13] m25p80: Add support for n25q512a11 and n25q512a13 Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 05/13] xilinx_spips: Move FlashCMD, XilinxQSPIPS and XilinxSPIPSClass Francisco Iglesias
2017-11-23 0:33 ` Alistair Francis
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 06/13] xilinx_spips: Update striping to be big-endian bit order Francisco Iglesias
2017-11-23 0:36 ` Alistair Francis
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 07/13] xilinx_spips: Add support for RX discard and RX drain Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 08/13] xilinx_spips: Make tx/rx_data_bytes more generic and reusable Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 09/13] xilinx_spips: Add support for zero pumping Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 10/13] xilinx_spips: Add support for 4 byte addresses in the LQSPI Francisco Iglesias
2017-11-23 0:37 ` Alistair Francis
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 11/13] xilinx_spips: Don't set TX FIFO UNDERFLOW at cmd done Francisco Iglesias
2017-11-23 0:39 ` Alistair Francis
2017-11-23 19:51 ` francisco iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 12/13] xilinx_spips: Add support for the ZynqMP Generic QSPI Francisco Iglesias
2017-11-03 0:01 ` [Qemu-devel] [PATCH v7 13/13] xlnx-zcu102: Add support for the ZynqMP QSPI Francisco Iglesias
2017-11-21 18:39 ` [Qemu-devel] [PATCH v7 00/13] Add support for the ZynqMP Generic QSPI Peter Maydell
2017-11-23 0:30 ` Alistair Francis
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171103000109.28244-1-frasse.iglesias@gmail.com \
--to=frasse.iglesias@gmail.com \
--cc=alistai@xilinx.com \
--cc=edgari@xilinx.com \
--cc=francisco.iglesias@feimtech.se \
--cc=mar.krzeminski@gmail.com \
--cc=peter.maydell@linaro.org \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.